Sean and Stephen 1593-RF07 RF07 WIRELESS PRESENTER User Manual Users manual
Sean & Stephen Corporation RF07 WIRELESS PRESENTER Users manual
Users manual
*145.00mm lfllll fill? Ilfl the RF-07fififiafiifififiéfiflfig e ts‘ial’fisfiflflz 1. tetfillSlSSfiAiuuss eatemsworssresaasee.nusaemmfimt $1 Of’DifiLEDgKfii‘EAIl'Eilkfifi- 2. fiffitéc‘fi’ztblfihfilt‘o‘fi fififlfiifilfitefilufiffilfifii flflififififfififiu—QB— BENEFB.$E§§M§Sl§7xfli§§flifiufl§§mLED%%B§(191014?).5.lDAlaB§i§'F LFflfififlgi’yifiEiflgflfilfififi(EELfilERifiEWQSBSLEDEEFfizTi/f swarm) . Hflflifiéfififiifixfiéfléfli Sigififififfifiifi- 3. seaplane. AWE}. g$i§§§fl2§i§fiif§flfiflfllfi<fififi§ifi§i®. 0 $§i§fi21013§2(§§§%m Wireless Presenter Manual For RF07 0 Instruction: 1_ plug receiver into USB Port,then the LED indicator on the receiver will be normallyon.lf not synchronise with the projector,the LED indicator will be off after 10 seconds,then the device will be on working status. - Synchrony: A source code had been set up before It leave factory, receive and project can be reciprocally used.For one-to-one synchrony status, when the LED indicator normally on(about 10 seconds).p|ease press down the up and down button all at once up to 4 seconds once plug the receipter in.if the synchrony is succssful, the LED will flash 2 times. If the product can’t page uplpage down as usual.please re-synchrony again 3. The red LED indicator will flash when the battery voltage less than 2.4V.(please change for new batteries) 0 Main button and function (Refer to below pic A): LEDi'é‘U—Rlfi LED indicator Receiver Page Up Page Down Green Laser Button fléfii'ci‘fiifi Red Laser Button E H Sean&Stephen it! ° . 1593-RF07 fififlfifix am EEEESQ >15M 0 Specification: , AAAx 2-cs 532 nm Green & 650 nm Red El <1 mW D <5mW 112401 9.2 MM VWndowsZOOO/ME/XPMsta 75.59 zo~30'c $ean&$tephen 1593-RF07 Brand name $3211 111? Enc’oR‘J 5g F5 89 E7? 115 fiiliifi Control Distance Batte x 2 cs 32 nm Green & 650 nm Red 01 léiiiill Ii’Ef-‘fiififfig \ 3 Output Power 0 EE$IE 1 112-4o*19.2 MM 1. %§%fiifiififififififlfl%- 2.MEfiKfifJ—nfiééfillt‘f/JG23KEBEEBQMB- [MI—— Noose. mazemmmseimme: %+:l§ 0 Caution: Eyfifiafigt821539¥§wfigfijfi.§§¢q,fla,§§fi§2l§figtfiflitggggfifi 1. Donotusethisdevicetoaim athuman oranimals'eyes. ennxmzaeeraaeazeafimsg. 2 fi-l—fllfi ' litIflfififlffi‘étfizE133$45;SZQRMfi$fi$t§8ifi§éi§zt§fiififi¥t§ifi§fliEH EDl$FB,#EQ§§%Ti§H§Eti—?fiifililfi snxeexsersasmeeeemezeeee.fimzeeemzfifasezfieals. ffi$fi§§fifi£fii§§flfi§méfilfi2¥fi The device is not a toy.PIease keep it out of the reach from children. *210.00mm —| l— *210.00mm % This equipment has been tested and found to comply with the limits for a Class 8 digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). Operation is subject to the following two conditions: 1)This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Caution! The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. Label and label location “111.80 mm —‘ *145.00mm
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Create Date : 2011:03:30 15:13:41+08:00 Creator : Adobe Acrobat 9.0 Modify Date : 2011:03:30 15:15:36+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Metadata Date : 2011:03:30 15:15:36+08:00 Creator Tool : Adobe Acrobat 9.0 Format : application/pdf Document ID : uuid:907d881c-4155-44de-b6f7-1821cb700971 Instance ID : uuid:a8a4563a-eff5-441d-910c-f3924fe62569 Producer : Adobe Acrobat 9.0 Image Conversion Plug-in Page Count : 1EXIF Metadata provided by EXIF.tools