Sears 580 75133 Users Manual
580751330 580751330 CRAFTSMAN PRESSURE WASHER - Manuals and Guides L0807093 View the owners manual for your CRAFTSMAN PRESSURE WASHER #580751330. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman PRESSURE WASHER Manual
CRAFTSMAN Power Washer, Gas Manual L0807093 CRAFTSMAN Power Washer, Gas Owner's Manual, CRAFTSMAN Power Washer, Gas installation guides
580.75133 to the manual 8e976832-d74e-4f0b-b9ef-601afeb317b0
2015-02-05
: Sears Sears-580-75133-Users-Manual-399610 sears-580-75133-users-manual-399610 sears pdf
Open the PDF directly: View PDF 
.
Page Count: 18
| Download | |
| Open PDF In Browser | View PDF |
OWNER'S MANUAL MODEL NO. 580.751330 ® 11 O0 PSi AT 1.6 GPM ELECTRnC HnGH PRESSURE WASHER DOUBLE nNSULATED HOURS: o Assembly Mon.- FrL 8 a.m. to 5 p.m (CST) ° Operation o Customer , Service and Adjustment . Repair Parts CAUTION: Read and Follow all Safety Rules and Instructions Responsibilities Before Operating This Equipment SEARS, ROEBUCK Part No 97068 Revision 1 (12/15!95) and CO., Hoffman Estates, IL 60179 U.S.A. iMPORTANT SAFETY INSTRUCT ONS Save these _ RISK WARNING instructions e Highpressurespraycan cause paintchipsor other particlesto become airborne and fly at high speeds OF ELECTROCUTION e Always wear eye protection when you use this equipment when you are in vicinity where the equipment is in use or e Operate the pressure at no more than the PSI fluid pressure rated for your pressure washer • inspect cord before every use Do not use if cord is damaged e Keep all connections dry and off the ground e Do not touch plug with wet hands e Double-insulated ment parts -- When servicing, use only identical replace- e Never move the machine by pulling on high pressure hose the handle provided on the top of the unit e This product shait only be connected to a power supply receptacle protected by a Ground Fault Circuit Interrupter (GFCI) e e Read instruction manual before using Use a respirator or mask whenever there is a chance that vapors may be inhaled Read all instructions with the mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors _ WARNING e High pressure spray may damage fragile items including glass Do not point spray gun at glass when in the high pressure mode e Keep the hose connected to machine or the spray gun while the system is pressurized Disconnecting the hose while the unit is pressurized is dangerous • Hold the spray gun firmly in your hand before you start the unit Failure to do so could result in an injury from a whipping spray gun Do not leave the spray gun unattended while the machine is running o Cleaning area should have adequate slopes and drainage to reduce possibility of a fal! due to slippery surfaces When usin 9 this p.roduct basic I_recautions ways be followed, including the fo owing: e Read all instructions before using the product should al- WARNING To reduce sary when the risk of injury close supervision product Is used near ch dren. is neces- Use e Know how to stop the product and bleed the pressure quickly Be thoroughly familiar with controls e Stay alert Watch what you are doing e Do not operate the product when fatigued or under the influence of alcohol or drugs e Keep water spray away from elect dc wiring or fatal electdc shock may result e Keep operating area clear of al! persons e Do not by-pass any safety device on this machine e Do not leave gun in closed position for more than 5 minutes with pressure washer running This could damage pump _WARNING Risk of injury or injection stream at persons, e e to persons - Do not discharge MAINTENANCE High pressure hose can develop leaks from wear, kinking, abuse, etc. Water spraying from a leak is capable of injecting mateda! into skin Do not point the pressure washer spray at people or animals Do not overreach or stand on unstable footing and balance at all times Operate and store this unit on a stable surface e Inspect hose each time before using it Check all hoses for cuts, leaks, abrasions or bulging of cover, or damage or movement of couplings If any of these conditions exist, replace hose immediately. Never repair high pressure hose. Replace it with another hose that meets minimum pressure rating of your pressure washer e Store in a clean, dry area Ideally, the unit should be stored in a frost-frae room Keep good e Follow the maintenance e This product shall only be connected to a power supply receptacle protected by a Ground Fault Circuit thterruptor (GFCI). This is done to comply with National Electrical Code (NFPA 70) and to provide additional protection from risk of electrical shock e instructions support specified in the manual Save these instructions TRAINING: e Locate this pressure washer in areas away from combustible materials, combustible fumes or dust e Some chemicals or detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning The harmful elements may cause property damage or severe injury e Do not allow CHILDREN time to operate the Pressure Washer at any AND STORAGE: e SERVICING OF A DOUBLE-INSULATED In a double-inselated product, two systems of insulation are provided instead of grounding. No means of grounding is provided on a double-insulated product, nor should a means for grounding be added Servicing a double-insulated product requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace, use only genuine replacement parts A double-insulated product Is marked with the words DOUBLE INSULATION" or "DOUBLE INSULATED" The symbol _may PREPARATION: EXTENSION • Before starting the Pressure Washer in cold weather, check all parts of the equipment and be sure ice has not formed there • Units with broken or missing parts, or without protective housing or covers should NEVER be operated OPERATION: e Do not spray flammable liquids e Never aim the gun at people, animals or plants • For household e High pressure stream of fluid that this equipment can produce can pierce skin and its underlying tissues, leading to serious injury and possible amputation use For indoor or outdoor use PRODUCT also be marked on the product CORDS Use only extension cords that are intended for outside use. These extension cords are Identified by a marking "ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES; STORE iNDOORS WHILE NOT IN USE" Use only extension cords having an electrical rating not less than the rating of the product. Do not use damaged extension cords. Examine extension cord before using and replace if damaged. Do not abuse extension cord and do not yank on any cord to disconnect it. Keep cord away from heat and sharp edges. Always disconnect the extension cord from the receptecie before disconnecting the pressure washer from the extension cord LOOK FOR THIS BECOME SYMBOL ALERT!!! TO POINT YOUR OUT IMPORTANT SAFETY PRECAUTIONS. "ATI'ENTION!!! SAFETY IS INVOLVED," IT MEANS CONGRATULATIONS on your purchase of a Sears Craftsman high pressure washer. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest Sears Service Center/Department or call the 1-800 number listed on the front of this manual. We have competent, well-trained technicians and the proper tools to service or repair this uniL Please read and retain this manual, The instructions will enable you to assemble and maintain your high pressure washer properly. Always observe the "SAFETY RULES." MODEL NUMBER OUTLET PRESSURE 1100 psi FLOW RATE t .6 gpm DETERGENT MIX Use undiluted detergent DETERGENT RATIO 17.1 WATER SUPPLY TEMPERATURE Not to exceed 104°F MOTOR Brush type (universal) RATED VOLTAGE 120 volts CURRENT 13 amperes 580.751330 MAgNTENANCE AGREEMENT SERIAL NUMBER A Sears Maintenance Agreement is available on this product. Contact your nearest Sears store for details. DATE OF CUSTOMER PURCHASE RESPONSIBILITIES o Read and observe the safety rules. THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE PRESSURE WASHER. e Follow regular schedule in maintaining, caring for and using your high pressure washer_ YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE. e Follow the instructions under"Customer Responsibilities" and "Storage" sections of this Owner's Manual_ FULL ONE YEAR WARRANTY ON CRAFTSMAN HIGH PRESSURE WASHER Forone yearfromthe dateof purchase,when thisCraftsman HighPressureWasheris maintainedend operated accordingto the instructionsinthe owner'smanual,Sears willrepair,freeof charge,any defect in material and workmanship If this washeris used for commercialpurposes,this warrantyappliesfor only90 daysfrom the date of purchase If this high pressurewasheris used for rental purposes,thiswarrantyapplies for only30 days afterdate of purchase, This warranty does not cover: Expendableitemssuch as spark plugsand air filters, which become worndudng normal use. _epairs necessary because of operator abuse or negligence, including damage resulting from no water being supplied to pump or failure maintain the equipment asoordlng to the instructionscontained in the owner's manual WARRANTY SERVICE IS AVAILABLE BY RETURNING THE HIGH PRESSURE WASHER TO THE NEAREST SERVICE CENTERJDEPARTMENT THROUGHOUT THE UNITED STATES. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state SEARS, ROEBUCK AND CO., D/817 WA, Hoffman Estates, IL 60179 3 SEARS TABLE OF CONTENTS SAFETY RULES .............................................................. CUSTOMER RESPONSIBILITIES 2 ....................................10 STORAGE ..................................................................... 11 CONTENTS OF HARDWARE PACK .............................. 5 TROUBLESHOOTING 12 ACCESSORIES REPLACEMENT PRODUCT SPECIFICATIONS ............................................. 3 AND ATTACHEMENTS ......................... 5 ASSEMBLY ....................................................................... .................................................. PARTS ............................................ 13-17 6 OPERATION .................................................................. 7-10 iNDEX -AAccessories ............... Assembly Checklist .......................... Removing from Carton ........... Set Up .......................... -R5 Replacement Parts ....... -H- 6 Hardware Pack ........... 6 6 High Pressure Hose ....... 5 6, 7 -MMaintenance Agreement ..... Nozzle .................. --Bin Before starting ............ Before each use .......... 9 10 Cleaning Tips ............. Customer Responsibilities. Check washe_components Electrical supply ........... Extension cords ........... Extensions, wand ........... Safety Rules ............... Siphoning ................ Specifications ................ Storage ...................... 2 10 3 11 Troubleshooting .......... 12 8 U 10 3,10 10 9 9 8 -OOperation Detergent Application ........... g KnowYourPressureWasher. _ 7 Stopping........................ 8 To Turn onWasher ................ 9 Order Parts ........ back page -GGround Fault Gun and Wand Assembly_.. -S- -T-NNozzle, adjustable ............ -C- 3 11 13-17 6-8 4 Utility brush ............. 7, 8 -WWarranty ................... 3 CONTENTS OF HARDWARE PACK Parts packed separately In carton Spray Gun Owner's Manual Utility Bn_sh and Adaptor High Pressure Hose Cleaning Kit Quick-Connect ACCESSORIES AND ATTACHMENTS These accessories and attachments were available when the high pressure washer was purchased_ They are also available at most Sears retail outlets and service centers, Most Sears stores can order these items for you when you provide the model number of your high pressure washer_ Some of these accessories may not apply to your pressure washer_ QUICK CONNECT WITH 2 ADAPTORS GARDEN HOSE 71 _75187 ROTATING BRUSH KIT 71-75199 FLOOR/SIDING BRUSH KIT 71-75190 MULTI-PURPOSE]HOUSE WASH 71-75100 UTILITY BRUSH KIT 71-75189 5 DECK WASH VEHICLE]BOAT 71-75101 WASH 71_75102 DEGREASER 71-75103 ASSEMBLY Read these instructions and Operator's Manual in its entirety before you attempt to assemble or operate your new high pressure washer. Your high pressure washer has, for the most part, been assembled at the factory, except those parts left unassembled_ Before you can operate your new high pressure washer', you must properly connect the high pressure hose. IF YOU HAVE ANY PROBLEMS WITH THE ASSEMBLY OF YOUR PRESSURE WASHER, PLEASE CALL THE PRESSURE WASHER HELPLINE AT 1-800-222-3136. TO REMOVE CARTON PRESSURE WASHER gun and wand assembly FROM ,, Remove holder. from cardboard o Remove all other packing material from box before removing your high pressure washer. FIG. 2 Refer to Page 5, "Contents of Hardware Pack" for an illustrated listing of all the items included with your pressure washer. Become familiar with each piece before assembling pressure washer. Check all contents against illustrations on Page 5 If any parts are missing or damaged, call the Pressure Washer Helpline. at 1-800-222-3136 HOWTO SET UP YOUR PRESSURE HIGH PRESSURE OUTLET WASHER Included with this unit is a quick-connect fitting that you attach to the water inlet. It can separate into two parts -- a male connector and a female connector that contains an inlet screen. Make sure this screen, as well as the intake supply filter, is clean. Attach the male connector of the quick-connect to the intake supply opening on the front of the pump (Fig 1). The water supply will be attached to the female connector. FIG. 3 INTAKE SUPF INTAKE SUPPLY FILTER FEMALE CONNECTOR INLET SCREEN FIG. 1 FIG. 4 = Unravel high pressure hose and attach to spray gun (Fig. 2). Tighten with two adjustable wrenches as illustrated, Do not try to tighten without holding second nut. o To attach the high pressure hose to the unit (Fig 3) push the "O"-ring connector of the hose.into the high pressure outlet and then hand tighten until secure. ,, Attach adjustable nozzle extension to spray gun by inserting threaded end of extension into end of spray gun and tightening the extension by hand until it locks in place (Fig. 4). CHECKLIST 6 ,, Check for proper hose connections (high pressure and water supply) and for tight connections and that there are no kinks, cuts, or damage to the high pressure hose_ ,, Provide proper water supply (not to exceed 104°F)_ ,, Be sure to read "Safety Rules" and "Operation" tions before using the pressure washer, sec- OPERATION KNOW YOUR HIGH PRESSURE WASHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER. Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustments, Save this manual for future reference. DETERGENT INTAKE SUPPLY OPENING PICKUP TUBE AND FILTER • MALE CONNECTOR RLTER INLET SCREEN "A" QUICK-CONNECT ESSURE OUTLET WAND (male connector, see also Fig "A") GUN TURBO NOZZLE FIG. 5 GUN AND WAND ASSEMBLY -- Controls the application of water onto cleaning surface with tdgger device Includes safety latch, UTILITY BRUSH--Used surface. to apply detergent and scrub PRESSURE HOSE DETERGENT PICKUP TUBE AND FILTER-and detergent in outlet water flow, Mixes water HIGH PRESSURE OUTLET -- Connection for high pressure hose, QUICK-CONNECT--Easy supply_ connection forintake water OPEBATBON HOW TO USE YOUR WASHER ADJUSTABLE NOZZLE IF YOU HAVE ANY PROBLEMS OPERATING YOUR PRESSURE WASHER, PLEASE CALL THE PRESSURE WASHER HELPLINE AT 1-800-222-3136. UTILITY STOPPING YOUR PRESSURE WASHER ,,F ADAPTOR FIG. 8 FIG. 7 HOW TO USE ADJUSTABLE NOZZLE FIG. 6 A o If the pressure washer is running, press the ON/OFF switch (Fig 6) o Simply shutting OFF washer will not release pressure in the system. Pull the trigger on the spray wand assembly to relieve the pressure in the hose_ NOTE: A small amount of water will squirt out when you release the pressure WAND EXTENSIONS Your high pressure washer comes equipped with a choice of three wand extensions -- one with an adjustable nozzle (Fig. 7), one with a utility brush (Fig. 8) and turbo nozzle (Not shown)_ Remove the adjustable nozzle extension if you wish to use the utility brush. Attach the Brush Adaptor to the utility brush and then insert the threaded end into the spray gun and hand tighten. NOZZLE IN HIGH PRESSURE MODE PUSH NOZZLE FORWARD FOR LOW PRESSURE MODE AND DETERGENT APPLICATION WARNING: NEVERNEVER ADJUST WHEN SPRAYING. PUT SPRAY HANDS PATTERN IN FRONT OF SPRAY NOZZLE TO ADJUST SPRAY PATTERN. With the adjustable nozzle you can adjust the spray pattern to be either high pressure or low pressure. You can also adjust the spray so it is concentrated in a stream pattern or expanded into a fan pattern. Use this nozzle to apply detergent = Push the nozzle attachment forward when you wish to adjust the spray to low pressure mode (Fig. 9) Pull the nozzle backward to achieve high pressure. ,, Twisting the nozzle adjusts the spray pattern from a narrow stream to an expanded stream. TWIST NOZZLE TO EXPAND SPRAY STREAM FIG. 9 TWIST NOZZLE TO NARROW SPRAY STREAM OPERATaON APPLYING DETERGENT WITH ADJUSTABLE NOZZLE PRESSURE A IMPORTANT: USE SOAPS DESIGNED SPECIFICALLY FOR PRESSURE WASHERS. HOUSEHOLD DETERGENTS ARE NOT RECOMMENDED. IMPORTANT: YOU MUST ATTACH ALL HOSES BEFORE YOU STARTTHE PRESSURE WASHER. STARTING THE PRESSURE WASHER WITHOUT ALL THE HOSES CONNECTED WILL DAMAGE THE PUMP, Pressure washers are useful cleaning tools designed to clean almost any surface in two easy steps, o o o The first step involves applying an appropriate detergent/solvent solution to penetrate and loosen grime. The detergent is applied at low pressure to avoid splashing, overspraying and waste, Leave the solution on surface for 3 to 5 minutes to allow solution to work. WASHING/RINSING WARNING: BE EXTREMELY CAREFUL IF YOU MUST USE PRESSURE WASHER FROM LADDER SCAFFOLD NG OR ANY OTHER RELATIVELY UNSTABLE LOCATION. PRESSURE IN A RUNNING WASHER BUILDS IN THE WAND AS YOU CLIMB. WHEN YOU PRESS THE TRIGGER, THE RECOIL FROM THE INITIAL SPRAY COULD FORCE YOU TO FALL, OR IF YOU ARE TOO CLOSE TO THE CLEANING SURFACE, HIGH PRESSURE COULD FORCE YOU OFF CLIMBING APPARATUS. Hook up water supply (Fig, 12) HIGH PRESSURE HOSE The second step involves cleaning the surface you have prepared with the pressure washer and then rinsing it clean. To apply detergent follow these steps: o o o Prepare your detergent solution as required by your job. Place small filter of the clear, detergent syphoning tube into the detergent container (Fig. 10), Set nozzle to low pressure mode, Detergent cannot be siphoned with nozzle in high pressure mode (see Fig_9), GARDEN HOSE FIG. 12 o Adjust nozzle to select high pressure mode (see Fig 9), NOTE; mode. o FIG. 10 o Start washer and apply detergent to a dry surface, starting from the bottom and working up _, Remove siphon from bottle to stop detergent in low pressure mode. Detergent will not flow when in the high pressure Start washer and work from the top of the surface to the bottom. NOTE: The high pressure mode is most effective when the tip of the wand is held between 8 to 24 inches from the surface being cleaned_ BEFORE STARTING PRESSURE WASHER NOTE: Detergents are most effective applied to a dry surface. To operate the unit you will need the following: HOW TO USE UTILITY o Electrical supply rated for 120 volts at 15 amps, o If using an extension cord, observe the following specifications: = BRUSH You can apply detergent with this nozzle, As you are applying detergent to surface you want to clean, you can also combine the liquid spray with scrubbing to clean very dirty areas, o You cannot adjust the spray pattern with this nozzle. o Store utility brush on top of handle (Fig_ 11)_ I o FIG. 11 9 CABLE LENGTH WIRE GAUGE Up to33 ft (10m) 33 to 66 ft. (tOm to 20m) 14/3 AWG 12/3 AWG Use only extension cords that are intended for outside use. These extension cords are identified by a marking "ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES; STORE iNDOORS WHILE NOT IN USE," Use only extension cords having an electrical rating not lessthan the rating of the producL Do not use damaged extension cord& Examine extension cord before using and replace if damage& Do not abuse extension cord and do not yank on any cord to disconnect iL Keep cord away from heat and sharp edges Always disconnect the extension cord from the receptacle before disconnecting the pressure washer from the extension cord, OPERATUON TO TURN ON WASHER WARNING: NEVER ADJUST SPRAY PATTERN WHEN WATER IS SPRAYING. NEVER PUT HANDS IN FRONT OF SPRAY NOZZLE TO ADJUST SPRAY PATTERN. ALWAYS KEEP HANDS IN THE POSITION SHOWN IN FIG. 9 CAUTION: Gun Idcks back. Use both hands. IMPORTANT: DO NOT RUN PUMP WITHOUT THE WATER SUPPLY CONNECTED AND TURNED ON OR THE PUMP WILL BE DAMAGED° SIPHONING We do not recommend that you siphon your water supply from sources other than from connecting to household water supply. TiPS WARNING: Risk of injury -- Do not discharge stream oratinjection persons. to persons e Check that high pressure hose is attached to pump outlet and that water supply is attached to pump inlet (female connector of quick-connect). o Initially clean an area and then check the surface for damage. If no damage is found, you can assume it is okay to continue cleaning Detergents work best when applied to dry surface. o For most effective cleaning, keep spray nozzle between 8 to 24 inches of cleaning surface. o Turn ON water.. Water supply should not exceed 104°F_ ,= Press trigger on gun and wand assembly to force air from high pressure hose (Fig. 12). o Allow the detergent to soak in between 3-5 minutes before washing and rinsing, = Maintain trigger as shown in Fig 12 and press ON/OFF switch. o For cleaning, start at lower portion of area to be washed and work upward, using long, even overlapping strokes For rinsing, push the nozzle sleeve to high pressure and wait for detergent to clear. Start at the top of area to be rinsed, working down with the same action as for cleaning. © FIG. 13 CUSTONER GENERAL Never use the garden hose inlet to siphon detergent or wax_ o If you get the spray nozzle too close, especially using high pressure mode, you may damage the cleaning surface. o If you have the spray nozzle too far away, the cleaning will not be as effective_ a Do not get closer than 6 inches when cleaning automobile tires. RESPONSIBILUTUES Check and Clean Quick-Connect Screen: Remove quick-connect and examine the inlet screen on the female connector. Clean if clogged or replace the quick-connect inlet screen. RECOMMENDATIONS The warranty of the high pressure washer does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain high pressure washer as instructed in this manual BEFORE o Check High Pressure Hose: High pressure hose can develop leaks from wear, kinking, abuse. Check all hoses for cuts, leaks, abrasions or bulging of cover, or damage or movement of couplings. If any of these conditions exist, replace hose immediately. EACH USE DANGER : WATER SPRAYING FROM A LEAK IS CAPABLE OF INJECTING MATERIAL INTO SKIN. INSPECT HOSE EACH TIME BEFORE USING IT. NEVER REPAIR HIGH PRESSURE HOSE. REPLACE IT WITH ANOTHER HOSE THAT MEETS MINIMUM PRESSURE RATING OF YOUR PRESSURE WASHER. Check Detergent Hose: Examine the filter on the deter; gent hose and clean if clogged. Hose should fit tightly on barbed fitting Examine hose for leaks or tears. Replace the filter or hose if either is damaged. Check Gun and Wand: Examine hose connection and make sure it is secure. Test trigger by pressing it and making sure it springs back into place when released. Put safety latch in ON position and test tdgger. You should not be able to press tdgger. ]0 STORAGE PRESSURE WASHER PUMP Test the pressure washer by operating in the high and low position. Water should not remain in the unit for long periods of time. Sediments of minerals can deposit on pump parts and "freeze" pump action_ After each time you are finished using your pressure washer, follow this procedure: o Flush detergent hose by placing the injector filter into a pail of clear water while running Pressure Washer with nozzle in low pressure mode Flush until you can see clear water flowing through hose, o Shut off the pressure washer, unplug it and let it cool, THEN REMOVE ALL HOSES_ o Store the pressure washer and its components in such a way as to protect it from freezing. o Store in a clean, dry araa. Ideally, the unit should be stored in a frost-free room. o Coil the high pressure hose and inspect it for damage. Cuts in the hose or fraying of it could result in leaks and loss of pressure, Should any damage be found, replace the hose. DO NOT attempt to repair a damaged hose and use it, Replace the hose with the genuine Craftsman parL o FIG. 14 Insert wire into nozzle and turn back and forth to clear obstruction. Drain water from hose and properly store it to prevent cuts and general wear_ NOZZLE MAINTENANCE If the nozzle becomes restricted or clogged with foreign materials, such as din, excessive pump pressure may develop. A partially clogged nozzle can cause a pulsing sensation during use. This generally is not a pump related problem, but rather a clogged or partially restricted nozzle, If the nozzle becomes clogged or partially restricted immediately clean the nozzle. o Disconnect the power supply and tum off the water supplyr O Separate the wand from the gun o Remove the nozzle from the end of the wand using a 2mm or 5/64 alien wrench. o Use a piece of wire or small paper clip to free the foreign materials (Fig. 14) from clogging or restricting the nozzle. ,, Use your water supply to back flush the wand removing additional debris. Back flush for 30 seconds to 1 minute (Fig. 15) Turn wand to stream spray position and move from low to high pressure while flushing ° Reinstall the nozzle into the wand, do not over tighten. o Reconnect wand to the gun, o Reconnect the water supply and turn on the water, o Reconnect the electrical power supply. FIG. 15 ]l TF OUBLESHOOTnNG WARNING: MANY THE ACTIONS YOU ARE ASKED CORRECT ARE PROBLEMS INVOLVE A COMPONENT OFOF THE PRESSURE WASHER. WHEN TO CLEANING ANY PART OF THIS THAT UNIT, TURN OFFCLEANING THE UNIT AND COMPLETELY DISCONNECT THE POWER SUPPLY. PROBLEM Pressure Washer will not start CAUSE CORRECTION 1 No electrical power is available. 1. Check cable, plug, power socket and fuse. 2 Motor overheats. 2 3_ Low voltage 4_ Trigger not open 5. Electrical defect Pressure Washer does not come up to pressure 1. Spray gun is in low pressuremode, 2 Pumpis sucking all 3+ Water filter clogged 4 Pump not bled to remove air High pressurespray is irregular_ No intakeof cleaning agent. 3 4 Press trigger of wand to relieve pressure on the uni[ Allow unit to cool for about 2 min. It should run when you turn it ON again. Length of extension cord is well beyond 66 feel Contact Sears Service Department Open trigger 5 Contact Sears Sevice Department. 1_ Adjust nozzle to high pressure mode. 2. Water hose must be 1/2" diameter Make sure water supply is ON. Make sure water supply is clean. Check all connections for leaks or blockage. Tum OFF the unit, hold trigger in OPEN position to relieve pressure and allow air in line to escape With tdgger still in OPEN position, tum ON the unit Repeat if necessery_ 3_ Clean filter_ 4. Switch OFF washer, press trigger, switch ON washer while pressing tdgger Repeat if necessary. 5_ Pump is defective 5. Contact Sears Service Department. 1_ Nozzle or water supply is restricted. 1. Clean nozzle, check hose and Screens_ 2_ Water supply inadequate. 2. Tum ON water to full position. Operate washer in suction operation with open container. 1. Wrong nozzle setting 2. Nozzle clogged_ 3, Detergent hose filter cloggecL 1, Adjust nozzle to low pressure mode_ 2_ Clean nozzle. ]2 3_ Clean tilter in detergent hose. CRAFSTIVlAN ELECTRIC HIGH PRESSURE WASHER 580.751330 REPAIR PARTS 15 13 9 ITEM 2 3 4 5 6 7 8 9 10 PART NO. 96154 96155 94313 94314 94315 96156 94316 94317 96157 DESCRIPTION SCREW (4 REQ,) MOTOR HOUSING (1 REQ+) GEAR WHEEL (1 REQ,) GASKET (1 REQ,) O-RING (1 REQ) ROTARY SHAFT SEAL (1 REQ,) BEARING (1 REQ+) SWASH PLATE (1 REQ+) ITEM 11 12 13 _4 15 16 17 18 SCREW (1 REQ) 13 PART NO. 96156 94307 94308 94369 96159 94310 94312 94311 DESCRIPTION MOTOR HOUSING (1 REQ) CABLE (2 REQ) SEAL (1 REQ ) CELLULAR RUBBER CORD (1 REQ+) HOUSING COVER (1 REQ+) _NSULATING MAT (1 REQ) MOTOR (1 REQ,) INSULATING MAT (1 REQ) CRAFSTMAN ELECTRIC HiGH PRESSURE WASHER 14 580.75"1330 REPAIR PARTS CRAFSTMAN ITEM 1 ELECTRIC HIGH PRESSURE WASHER PART NO. DESCRIPTION 96160 HOUSING (1 REQ,) 580.751330 SPILL VALVE 1 (REQ,) 2 SLEEVE (1 REQ,) 3 4 96161 SELF-TAPPING SCREW (2 REQ.) 5 96162 SPARE PARTS KIT (1 REQ,) 6 96163 PUMP COVER (1 REQ.) 19,3 x 2Atom O-RING (1 REQ_) 7 6 94304 NOZZLE INSERT (1 REQ,) 9 96164 OVAL HEAD SCREW (4 REQ) 10 94302 10 x 2,5ram O-RING (3 REQ) VALVE (3 REQ) 11 76 x 2ram O-RING (1 REQ) 12 13 96165 CYLINDER HEAD (1 REQ) 14 94303 PISTON (3 REQ,) 15 94305 HELICAL SPRING (3 REQ) 16 96166 HOUStNG (1 REQ,) 17 94306 GROOVED RING (3 REQ,) 18 19 20 21 22 WASHER (3 REQ,) GROOVED RING (3 REQ,) O-RING (3 REQ,) PRESSURE VALVE (3 REQ.) GASKET (1 REQ.) * -- Part Is included with Pump Repair Kit (Part No 94301) ]5 REPAIR PARTS CRAFSTIVIAN ELECTRIC HIGH PRESSURE WASHER 4 580.751330 REPAIR PARTS 21 5 18-- _Z_,_ I 1 17 14 16 16 CRAFSTMAN ITEM ELECTRIC PART NO. HIGH PRESSURE WASHER 580.751330 DESCRIPTION 1 94293 COVER (1 REQ.) 2 94294 FILTER (1 REQ) 3 94295 HOSE (1 REQ) 4 96150 SCREW (7 REQ) 5 94296 ELECTRIC CORD (1 REQ) 6 94297 CORD BUSHING (1 REQ,) 7 94298 SWITCH (1 REQ) 8 96151 BRACKET (1 REQ ) 9 94299 PROTECTING CAP (1 REQ,) 10 96152 SWITCH FRAME(1 REQ) 11 96153 RUBBER BUFFER(4 REQ) 12 96016 QUICK DISCONNECT ADAPTOR (1 REQ) 13 94306 WATER INLET FILTER (1 REQ.) 14 95602 WAND EXTENSION (1 REQ) 15 95563 SPRAY GUN (1 REQ,) 16 95604 HIGH PRESSURE HOSE [25 FT,] 1 (REQ.) 17 88185 UTILITY BRUSH (1 REQ,) 18 95577 ATTACHMENT ADAPTOR (1 REQr) 19 97068 OWNER'S MANUAL (1 REQ) [not shown] 20 95566 TURBO WAND (1 REQ) 21 96017 QUICK DISCONNECT ADAPTOR - MALE (1 REQ,) 17 REPAIR PARTS ® OWNER'S MANUAL 1100 PSi AT 1.6 GPM ELECTRIC HiGH PRESSURE DOUBLE iNSULATED WASHER [-_1 Each High Pressure Washer' has its own model number. MODEL NO. The model number for your pressure washer' will be found on a decal attached to the unit. 580.751330 All parts listed herein may be ordered through Sears, Roebuck and Co Service Centers and most Retail Stores. IF YOU NEED REPAIR SERVICE WHEN ORDERING REPAIR LOWING INFORMATION: OR PARTS e e FOR REPAIR SERVICE CALL THIS TOLL FREE NUMBER PRODUCT--HIGH MODEL PARTS, ALWAYS PRESSURE NUMBER-- GIVE THE FOL- WASHER 580.751330 @ PARTNUMBER 1-800-4_REPAIR e PART DESCRIPTION (1-800-473_7247) FOR REPLACEMENT PARTS INFORMATION AND ORDERING, CALL THIS TOLL FREE NUMBER: 1-800-FON-PART Your Sears merchandise has added value when you consider that Sears has service units nationwide staffed with Sears trained technicians._.professiona! technicians specifically trained on Sears products, having the parts, tools and the equipment to ensure that we meet our pledge to you, we service what we sell (1-800-366-7278) SEARS, ROEBUCK Part No 97068 Revision 1 (12/15/95) and CO., Hoffman Estates, IL 60179 U.S.A. Pdnted in US A
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 18 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Mon Jul 21 04:43:30 2008 Author : Title : Subject :EXIF Metadata provided by EXIF.tools