Secure Wireless EV-DWV2 Vanishing2 Door/Window Sensor User Manual EV DW4975 user

Secure Wireless, Inc Vanishing2 Door/Window Sensor EV DW4975 user

User manual

Download: Secure Wireless EV-DWV2 Vanishing2 Door/Window Sensor User Manual EV DW4975 user
Mirror Download [FCC.gov]Secure Wireless EV-DWV2 Vanishing2 Door/Window Sensor User Manual EV DW4975 user
Document ID1124823
Application IDFTqHSpSrIDM3aBUD53HMVA==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize3.21kB (40183 bits)
Date Submitted2009-06-15 00:00:00
Date Available2009-06-15 00:00:00
Creation Date2008-09-25 16:47:03
Producing SoftwareGPL Ghostscript 8.15
Document Lastmod2008-09-25 16:47:03
Document TitleMicrosoft Word - EV-DW4975_user.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: jstone

EV-DWV2 Vanishing Door/Window Contact- Installation Manual
Introduction
The EV-DWV2 is a miniature supervised door/window
contact allowing a multitude of applications while
hiding the transmitter on a door or window frame. The
EV-DWV2 uses a replaceable lithium battery and
should last 5 years under normal usage.
Install or Replacing the Battery
The EV-DWV2 uses a Panasonic CR2032 Lithium
Battery and is shipped not installed to save battery life.
Follow the steps below to install or replace the battery.
1) Using a coin or a flat head screw driver, insert into
the notch located on the case and gently twist to open.
Lift up and pull the case outward to open.
2) Insert Battery with + side facing UP.
Use care when installing the battery and observe the
correct polarity when the battery is inserted . Use only
Panasonic Lithium CR2032 batteries for replacement.
WARNING!: Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.
Mount Transmitter and Magnet
1)Mount the EV-DV2 on any window or door frame
using the supplied double strick tape or screws.
2) Find the notch on the outside of the EV-DWV2
enclosure. Align the manget with the nothces and
ensure that the distance is no greater than 5/8 of an
inch.
Enrolling
Refer to your installation manual for enrolling wireless
devices into a DSC control panel.
Temperature Specifications:
The EV-DW4975 is not design to be placed in an
environment where the temperature drops below -10C
or goes above +50C. Temperatures below -10C can
cause the EV-DWV2 to falsely report a low battery
after a few years of service. As the battery depletes over
time the internal impedance increases and at extreme
temperatures below -10C can cause a false positive. If
you choose to use the EV-DWV2 in an environment
below -10C, the battery life can be reduced to as little
as 3 years instead of the specified 5 years of life.
FCC/IC Compliance Statement:
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2008:09:25 16:47:03
Modify Date                     : 2008:09:25 16:47:03
Title                           : Microsoft Word - EV-DW4975_user.doc
Creator                         : PScript5.dll Version 5.2.2
Author                          : jstone
EXIF Metadata provided by EXIF.tools
FCC ID Filing: QNPEV-DWV2

Navigation menu