Secure Wireless EV-F433PS Security Remote Transmitter User Manual 6940 SW DSC WS4938 Panic

Secure Wireless, Inc Security Remote Transmitter 6940 SW DSC WS4938 Panic

User Manual

Belt Clip Assembly and Mounting(Screws not included)Limited WarrantyDigital Security Controls Ltd. warrants that for a period of 12 months from the date of purchase,the product shall be free of defects in materials and workmanship under normal use and that infulfillment of any breach of such warranty, Digital Security Controls Ltd. shall, at its option, repairor replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of Digital Security ControlsLtd. such as lightning, excessive voltage, mechanical shock, water damage, or damage arisingout of abuse, alteration or improper application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of anyand all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. Digital Security Controls Ltd. neither assumesresponsibility for, nor authorizes any other person purporting to act on its behalf to modify or tochange this warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequentialdamages, loss of anticipated profits, loss of time or any other losses incurred by the buyer inconnection with the purchase, installation or operation or failure of this product. Warning: Digital Security Controls Ltd. recommends that the entire system be completely tested on aregular basis. However, despite frequent testing, and due to, but not limited to, criminal tamperingor electrical disruption, it is possible for this product to fail to perform as expected.Important Information: Changes or modifications not expressly approved by Digital SecurityControls Ltd. could void the user’s authority to operate this equipment.FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd.could void your authority to use this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must acceptany interference received, including interference that may cause undesired operation.IC: 160A-WS4938 The term ‘IC:’ before the radio certification number only signifies that IndustryCanada technical specifications were met.©2003 Digital Security Controls Ltd., Toronto, Canada Technical Support: 1-800-387-3630 • www.dsc.comPrinted in Canada 29034684 Rev 001 Direct all comments concerning this publication to pubs@dscltd.comWS4938 Wireless Panic ButtonOperating InstructionsCongratulations on your purchase of the WS4938, DSC’s wirelesspanic button. This unit was designed to transmit an emergency signalfrom any location within the range of the alarm system. Signals from the button will be transmitted whether the system is armed or disarmed.The button is small and lightweight enough to be placed in a shirtpocket or tucked away inside purse. It can also be used with the supplied neck strap or multi-functional clip, which can connect to your belt, car visor or permanently mounted to a convenient location.To activate, press and hold the key for approximately 2 seconds. The LED located on the top of the unit will light up to confirm a signal has been set.Note: Signals will not be received if the key is not within range of the wireless receiver.Activating, Enrolling and ProgrammingTo conserve battery power the unit comes deactivated. To activate simply remove the cover andslide the switch to the ON position (to the left).Enroll the WS4938 using the 6-digit number located on the device. This device is supervised. If the unit is removed from the coverage range a trouble will beindicated on the system. If this is not desired the supervisory bit for this zone must be disabledon the receiver. Please refer to your receiver instruction manual for details on enrolling wirelessdevices and disabling supervision.CompatibilityThe WS4938 is compatible with the following receivers;PC4164-433, PC5132-433, RF5108-433, RF5501-433, NT9005 and NT9010Replacing the BatteriesUnder normal conditions the batteries can last up to 2 years. If the battery is low the trouble light on the controls panel’s keypadwill turn ON.To replace the battery, remove the top cover by inserting a coininto the slot located on the bottom right corner and twist. Removethe screw at he center of the board to expose the batteries.Replace both batteries with Panasonic CR-2025 lithium batteries (see diagram).NOTE: The polarity of the battery must be observed, as shown in the diagram above. Improper handling of lithium batteries may result in heat generation, explosion or fire, which may lead to personal injuries.WARNING: DANGER OF EXPLOSION IF BATTERIES ARE INSTALLED INCORRECTLY.REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THEMANUFACTURER.Keep away from small children. If Batteries are swallowed, promptly see a doctor. Do not try torecharge these batteries. Disposal of used batteries must be made in accordance with the wasterecovery and recycling regulations in your area.

Navigation menu