Secure Wireless PBTX Handheld Transmitter User Manual PB Manual
Secure Wireless, Inc Handheld Transmitter PB Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 668687 |
| Application ID | vmarredMnY8UV7I7C78oQA== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 11.32kB (141529 bits) |
| Date Submitted | 2006-06-14 00:00:00 |
| Date Available | 2006-06-09 00:00:00 |
| Creation Date | 2006-06-02 00:05:26 |
| Producing Software | Acrobat Distiller 5.0.5 (Windows) |
| Document Lastmod | 2006-06-09 15:10:26 |
| Document Title | Microsoft Word - PB Manual.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | choque |
User Instructions for PBTX Transmitter and PBRX Receiver. Installation: Transmitters are shipped with batteries installed. First verify transmitter is operational by pressing any of the four buttons. The status LED at the top of the transmitter will flash rapidly. If LED does not flash then check batteries. If LED flashes at slower rate then the batteries are low and need to be replaced. Use care when installing the batteries and observe the correct polarity when the batteries are inserted . Use only CR2450N type batteries for replacement. WARNING!: Battery may explode if mistreated or replaced with incorrect type. Do not recharge, disassemble or dispose of in fire. Dispose of used batteries properly. The receiver can now be installed. Secure the receiver to machine so that all wires will not get pinched or fray on sharp edges. If mounting is a high vibration area it is recommended that receiver is mounted with shock mounts. Next, mount antenna to the flat metal part of the machine. For best performance make sure antenna is able to be seen by the transmitter at all times. Operation: Receiver input voltage is +24VDC and is connected to J2 Pin 1. The return (GND) is attached to J2 PIN 2. When power is attached a green LED will turn on. Each button turns on the transmitter and transmits the defined button closure. The receiver then decodes the button and closes the appropriate relay. All relays commons are tied together and to J2 PIN 3. When a relay closes what ever is connected to PIN 3 will then be connected to the output of the activated relay. I.e. by pressing the start key J2 PIN 4 has the potential of J2 PIN3. All buttons can be pressed at the same time as long as any single path does not excide 10A. Functionality: Pressing the green start button on the transmitter will close relay 1 on the receiver. Pressing the red stop button on the transmitter will close relay 2 on the receiver. Pressing the yellow cycle button on the transmitter will close relay 3 on the receiver. Pressing the white ALT button on the transmitter will close relay 4 on the receiver. While pressing the function you can see a LED flashing at the same rate as the transmitter. If LED flashes at a slower rate then not all of the transmitter packets are getting to the receiver. Specificatioins: System Functions Frequency Modulation Data Response time Data security Operating range Temperature Range Approvals 4 Digital on / off 433.92MHz Amplitude Modulation Manchester encoded 60ms 16777216 Unique Addresses 16 Bit CRC 100 Feet -40 to 70 degrees C FCC, Canada ISC, CE Transmitter Size Weight Sealing rating Diagnostics Labeling Antenna Batteries Battery life 4.15” (105.3mm) x 2.17” (55mm) x .86” (21.8mm) 3.5 oz with batteries IP66 NEMA 4X Red TX status / low battery LED Serial #, Model #, Approvals, IEC ICONS Internal 2 x 3V lithium CR2450 40 hours continuous operation Receiver Size Weight Diagnostics Programming Supplied voltage Contact current I /O Connector Antenna 4.54” (115.3mm) x 2.633” (66.8mm) x 1.1” (2.79mm) 7oz Red status (signal, TX low battery) LED Green power LED Learn switch 24VDC 10A maximum Amp 12 Pin Mate-n-lock BNC Rubber Duck FCC/IC Compliance Statement: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2006:06:02 00:05:26Z Modify Date : 2006:06:09 15:10:26-07:00 Page Count : 3 Creation Date : 2006:06:02 00:05:26Z Mod Date : 2006:06:09 15:10:26-07:00 Producer : Acrobat Distiller 5.0.5 (Windows) Author : choque Metadata Date : 2006:06:09 15:10:26-07:00 Creator : choque Title : Microsoft Word - PB Manual.docEXIF Metadata provided by EXIF.tools