Securitron WTMN1A_24SEP08 WT1 Wiring And Use Instructions I 500 63020 A

User Manual: Securitron WT1 Wiring and Use Instructions Installation Instructions

Open the PDF directly: View PDF .
Page Count: 4

WT1 Wiegand Test Unit : Wiring and Use Instructions

FOR INSTALLATION ASSISTANCE, CALL 1-800-810-WIRE

Copyright © 2008, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part

without the express written permission of ASSA ABLOY Inc. is prohibited.

WTMN1 – PAGE 1

CONTENTS WT1, plastic, 6.25” x 3.5” x 2.375”

AC / DC power adapter

ElectroLynx cable

Wiring harness

As part of their promise to provide innovative, fast and

effective, and higher security solutions to their customers,

ASSA ABLOY Group companies offer ElectroLynx, a universal

quick-connect system that simplifies the electrification of

the door opening. ElectroLynx™ is a trademark of ASSA

ABLOY, Inc.

Designed for compatibility with ASSA ABLOY products and

other Wiegand output devices, the ASSA ABLOY WT1, or

Wiegand Test Unit, is a user-friendly tool that demonstrates

products features and capabilities.

The WT1 also provides field troubleshooting by verifying

proper wiring, card reader data integrity, lock functionality

including lock/unlock, door position status, and request-to-

exit (REX) status.

The WT1 connects directly to Wiegand output for testing.

Connect your product's interface board (if required) to

translate to Wiegand, then connect the WT1 to the interface

board. If your product does not need an interface board to

provide Wiegand output, you may connect it directly to the

WT1.

To connect the WT1 to the product, use the enclosed

ElectroLynx cable; if an interface board is required, connect the

WT1 to the interface board using the enclosed wiring harness.

TEST BOX

PRODUCT

DESCRIPTION

Adapter

End View

n Fail Safe /Fail Secure Selector

o Open Override

p Learn Button

q 12VDC / 24VDC Selector

r To Power Adapter

s To Lock

function of interface module

^ LEDs refer to the following product features:

DPS Door position switch

RX Request to exit

LX Latch bolt monitoring

DX Dead bolt monitoring

CX Cylinder monitoring (not currently in use)

TMPR Tamper

VISUAL

MONITORING

INDICATORS

PWR ON Indicates unit powered

IMPORTANT 1. Disconnect unit to be tested from access control

system before servicing.

2. Installer must be a trained, experienced service

person.

3. Wiring must comply with applicable local electrical

codes, ordinances and regulations.

4. Unit is grounded to Common (-) for Electrostatic

Discharge (ESD) protection. Use appropriate ESD

practices when handling the circuit board, (i.e.

standard grounding precautions). Common (-) must

be grounded to earth (EG) at the power supply.

5. Ensure that no wires are pinched or damaged during

installation.

Install equipment on door according to manufacturer’s instructions. Please refer these websites for installation

instructions at:

INSTALLATION

INSTRUCTIONS

ASSA ABLOY: www.intelligentopenings.com

HES: www.hesinnovations.com

Securitron: www.securitron.com

1 2 34

6

5

6

1 2 34

7

WT1 Wiegand Test Unit : Wiring and Use Instructions

FOR INSTALLATION ASSISTANCE, CALL 1-800-810-WIRE

Copyright © 2008, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part

without the express written permission of ASSA ABLOY Inc. is prohibited.

WTMN1– PAGE 2

CONNECT THE WT1 To connect the WT1, determine whether your lock provides a direct Wiegand output, or if it requires an

interface panel to convert to Wiegand.

If your lock is direct-connect, follow the diagram under the ElectroLynx Wiegand Wiring Diagram. If your

lock requires an interface panel, follow the diagram under Wiring Diagram for Interface Board to WT1.

ElectroLynx Hinge with Pin Connections

Lock Cable ElectroLynx Cable to WT1

ELECTROLYNX

WIEGAND WIRING

DIAGRAM

Use the provided

ElectroLynx cable when the

product has direct Wiegand

output.

Lock to

WT1 Connections

Notes

The System is designed to

be installation friendly with

ElectroLynx quick

connectors.

Hinge With ElectroLynx

Cable Detail

Important

ElectroLynx connectors plug

and lock together in only

one way, as shown. Do NOT

force connectors together.

Reference ElectroLynx

Catalog A7738.

Power Input AC 100 – 240V 800mA 50Hz/60Hz

Power Output The WT1 is capable of supplying a total of 900 MA output to the unit under test.

The 900 MA is the total output for both reader interface and the lock.

PIN ASSIGNMENT TABLE FOR WIRE HARNESS

The following chart shows the wiring assignments for the wire harness included with the WT1. This harness is only used when the lock's

output must first go through an interface board to translate to Wiegand.

See the connection diagram on the following page for how to wire the interface board to the WT1.

PIN # DESCRIPTION WIRE COLOR WIRE CABLE ELYNX CABLE MISCELLANEOUS COMMENTS

1 Reader Power - Black Controller TS1 8 PIN -1 Ground

2 Reader Power + Red Not Used 8 PIN -2 +12 VDC always

3 Wiegand Data 1 White Controller TS4 8 PIN -3 +5 goes to ground for data 1 bit

4 Wiegand Data 0 Green Controller TS4 8 PIN -4 +5 goes to ground for data 0 bit

5 REX Switch NC/NO (Keeper Switch on Strike) Orange Controller TS4 8 PIN -5 LED on when REX used or when Keeper closed

6 REX Switch COM (Keeper Switch on Strike) Blue Controller TS4 8 PIN -6 LED on when REX used or when Keeper closed

7 Beeper Control - Cylinder Switch Brown Not Used Not Used

8 LED Control Yellow Not Used 8 PIN -8 +5 goes to ground to turn LED Green

9 Lock Power Violet Not Used 4 PIN -1 Ground

10 Lock Relay Out Grey Not Used 4 PIN -2 Lock Power+

11 DPS Switch NC/NO Pink Controller TS4 4 PIN -3 LED on when switch closed

12 DPS Switch COM Tan Controller TS4 4 PIN -4 LED on when switch closed

13 Beeper Control Brown Controller TS4 Not Used +5 to turn Beeper on

14 LED Control Yellow Controller TS4 Not Used +5 to turn LED Green

15 Dead Bolt Switch NC/NO White/Orange AUX Board TS1 AUX-2 Not Used LED on when secure (Dead Bolt extended)

16 Latch Bolt Switch NC/NO White/Red AUX Board TS1 AUX-1 Not Used LED on when secure (Latch Bolt extended)

17 Cylinder Switch NC/NO - Spare White/Black Not Used Not Used LED on when Key in use (future)

18 Tamper Relay NC/NO White/Blue Controller TS1 Not Used LED on when Tamper true

19 Lock Power + / Controller Power Red Controller TS1 See Table 1 v.N1 controller can be 12 or 24 (switch selected)

20 Lock Relay IN Violet See Table 1 See Table 1 Use for Fail Secure Lock

Rece

p

tacle

Lockin

g

Mechanism

Plu

g

WT1 Wiegand Test Unit : Wiring and Use Instructions

FOR INSTALLATION ASSISTANCE, CALL 1-800-810-WIRE

Copyright © 2008, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part

without the express written permission of ASSA ABLOY Inc. is prohibited.

WTMN1 – PAGE 3

WIRING DIAGRAM FOR INTERFACE BOARD TO WT1

The following wiring diagram shows how to connect the WT1 wiring harness:

ElectroLynx

To

Interface

Board

Wie

g

and Test Box Wirin

g

Harness Connections

(

re

f

er to Wire Harness Table

)

WT1 Wiegand Test Unit : Wiring and Use Instructions

FOR INSTALLATION ASSISTANCE, CALL 1-800-810-WIRE

Copyright © 2008, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part

without the express written permission of ASSA ABLOY Inc. is prohibited.

WTMN1– PAGE 4

OPERATING

INSTRUCTIONS FOR

ALL CARDS

NOTES: Failure to

connect the WT1 to the

lock before applying

power result in false

reads.

The WT1 is capable of

remembering up to the

last 20 programmed, or

learned, cards. To clear

all cards from memory,

hold down the learn

button while applying

power.

The door device green

LED flashes.

To initialize the test box for all cards:

1. Connect all wires to the WT1 first.

2. Select Fail Safe or Fail Secure according to sample.

3. Select the appropriate solenoid lock voltage (12 or 24 VDC).

4. Apply power to the WT1.

5. Once the door device completes its visual and audio signaling, it will unlock

when ANY Wiegand card is presented.

OPERATING

INSTRUCTIONS FOR

LIMITED NUMBER

OF CARDS

NOTES: Failure to

connect the WT1 to the

lock before applying

power result in false

reads.

The WT1 is capable of

remembering up to the

last 20 programmed, or

learned, cards. To clear

all cards from memory,

hold down the learn

button while applying

power.

The door device green

LED flashes.

To initialize the test box for a limited number of specific cards:

1. Connect all wires to the WT1 first.

2. Select Fail Safe or Fail Secure according to sample.

3. Select the appropriate solenoid lock voltage (12 or 24 VDC).

4. Apply power to the WT1.

5. Present a card to the lock.

6. That card is recognized and added to the list of cards that will unlock the

lock. Other cards will not work until each is presented while holding down

the learn button.

NOTES Once a single card/cards are recognized, the door device will no longer

operate by the presentation of any random card until it is been reset.

To reset the device, cycle the power while holding the learn button until it

flashes three times. Any card will then activate the lock.