Security Group SSG-T6 Security alarm system User Manual 1
Shenzhen Security Group Corp., Ltd. Security alarm system 1
UserManual.wiki
>
Security Group
>
SSG T6 User Manual
SSG-T6L_FCC_User Manual Rev. 1
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![Control Panel OperationAlarm ControlArm (Away Arm)Press the button on the [Arm ]control panel, the system enters armstate when one beep is heard and thearm LED Indicator lights on.Emergency CallWhen the LCD display is activated, Hold the button for 3 seconds [ ]the system goes into emergentalarming state with siren hooting,meanwhile the panel will auto dial pre-stored alarm phone numbersHome Mode (Part Arm)Press the button on [Home Mode ]the control panel, the system entershome mode when one beep is hearand the home mode LED Indicator lights on. All the normal sensor arearmed except the home mode sensorswhich are disarmed, so that user canmove freely at home.DisarmInput user code (Default: 1234) or admin code (Default: 123456) firstthen press the button, [Disarm ]the system enters disarm state when one beep is heard and the disarm LED Indicator lights on.Note: If Entry/Exit Delay is activated, all zones except the 24-hour zone will enter arm state after the set delay time.0506](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-5.png)
![The control panel has a RFID reader for unlocking the electronic door lock by disarming the system. Just place the RFID tag close to the RFID reader, the blue LED indicator flashes once. The system is disarmed and the electronic door lock is opened (If connected).Access Control SystemIf you input wrong numbers, press button and input again. Press button to [Esc] [Esc]cancel dialing or press button to end a conversation.[Call ]24Function SettingInput the admin code (Default: 123456), and then press to enter setting menu. [Enter] Up Down Enter Confirm Back to last step EscNote: If control panel is connected with extension line, 0# or 9# need to be added in front of the phone number when making phone calls. if the land line is unavailable, system will switch to GSM network, user can make phone calls by inputting phone number directly without 0# or 9#.070813When the control panel is in disarm or home mode state, press button,Type the phone number you wish to call and press . [Call ][Call ]Make Phone CallsThe control panel has a built-in communication module. If the PSTN land line is connected or SIM card is connected properly, and the credit is enough, you can use the panel to make calls.(a)Through SIM card(b)Through landlineWhen the control panel is in disarm or home mode state, press button,Type the phone number you wish to call and press button. [Enter][Call ]Voice MemoPress the button for 1 second to record 10 seconds voice [Record Voice Memo ]message. The circle Play Voice Memo will be flashing to remind you. Users can touch the center of circle to listen to the voice memo. The LED indicator blacks out when the voice memo has been played. Replay by touching it again.The latest voice memo will cover the former message.](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-6.png)
![09 10In the table below,each colummn represents a menu or a sub menu,Each menu or submebu will be displayed on on of the two lines of LCD display.On the LCD display,the current menu,submenu or setting is shown on the line at the bittom,while the previous menu or sub menu is shown on the line at the top.Navigate the select the setting you wish to modify with the keys" " or" ", and enter each menu or sub menu by pressing " "button.EnterHow to use the touch keypad:Delete:Down:Up:Confirm/select:Back/CancelMain Menu Sub menu 1 Sub menu 2 Sub menu 3Phone numbersAccessoriesRemoteAdd a newDelete all?Delete one*Please connect within 30s1=YES 0=NOEnter 01-30RFID TagAdd a newDelete all?Delete one*Please connect within 30s1=YES 0=NOEnter 01-99Wireless sensorsAdd a newDelete all?Delete one*Please connect within 30s1=YES 0=NOEnter 01-99Test modeSystem settingsDate and Time 20xx-xx-xx xx:xxEntry Exit delay Entry delayExit delay* 0-300s* 0-300sAuto arm/disarmAuto arm time 00:00Auto disarm timeOn or Off00:00Control by phone On or OffLine cut alarm On or OffKeypad tones On or OffGSM fail tip On or OffSystem settingsMain Menu Sub menu 1 Sub menu 2 Sub menu 3Access codeAdmin codeUser codeDuress codeOpen door code6 digits:1234564 digits:12344 digits:00004 digits:8888Ring time 0-9Wired sirenSiren alert timeBuilt-in sirenWireless sirenSiren setupON or OFF0-9 minON or OFFON or OFFUser ID 4 digitsArm Upload ON/OFFDisarm Upload ON/OFFCall recycle 0-9Backlight time 0-300sReset 1=Yes 0=NOAboutLanguageEnglish,FrenchGerman,SpanishFinnish,SwedishNorwegian,DanishTialian,ChineseHistory- ----- ------------ ----1-150Phone [1-5] isSMS Num [1-5] isCMS Num [1-2] isSpeed dial Num](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-7.png)
![11 12(1)Add/delete remote&keypadAdd a)Log on setting menu, , choose “Accessories”, press [Enter].b) , choose “Remote”, press .[Enter]c) , choose “Add a new”, press .[Enter]d)Press any button on the remote control within 30s,the control panel will sound a beep,and the LCD will show “ ”.if the remote Add OK,Remote 01-30already has been added before,the control panel will sound 2 beeps and the LCD will show “ ”already exists* When you add more remote control ,the remote control number will add 1 automatically from 01 to 30.DeleteDelete a remote control &keypad[Enter]a)Log on setting menu, ,choose “Accessories”, press .b) , choose “Remote”, press . [Enter]c) , choose “Delete one”, press .[Enter]d)Enter the remote control number(01-30) you want to delete ,the control panel will sound a beep if delete succeeded.Delete all remote control&keypad [Enter]a)Log on setting menu, ,choose “Accessories”, press .b) , choose “Remote”, press .[Enter]c) , choose “Delete all”, press .[Enter]d)Enter “1” delete all the added remote control ,the control panel will sound a beep if delete succeeded.(2).Add/delete RFID tagAdd b)Log on setting menu, ,choose “Accessories”, press .[Enter]b) , choose “RFID tag”, press . [Enter]c) , choose “Add a new”, press .[Enter]d)Swipe the RFID tad on the RFID reader within 30s,the control panel will sound a beep, and the LCD will show “ , RFID tag 01-50”.if the RFID Add OKtag already has been added before ,the control panel will sound 2 beeps and the LCD will show “ s”already exist*When you add more RFID tags ,the RFID tag number will add 1 automatically from 01 to 50.1. Alarm Phone Number Setting2. Add/delete accessoriesBefore enter into setting menu,please disarm the system first.Type the Admin password and then press “Enter” button on the control panel to enter into setting menu.Settings Important: The default language of this alarm system is English, you can change in the [Language] [System Setting] menu of .User can store 5 alarm phone numbers 5 SMS alert phone numbers and 2 CMS numbers.Add phone numbera)Log on setting menu,press ,choose “Phone Numbers”, press .[Enter]b) ,choose the group of phone number you want to add, press .[Enter]c)Input alarm phone numbers, press to save. [Enter]Delete phone number[Enter]a)Log on setting menu, choose “Phone Numbers”, press .b) , choose the group of phone number you want to delete, press .[Enter]c)Press to delete, press to confirm.* [Enter] or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-8.png)
![13 14(3)Add/delete wireless sensorsAdda)Log on setting menu, ,choose “Accessories”, press .[Enter]b) , choose “wireless sensor”, press .[Enter]c) , choose “Add a new”, press .[Enter]d) , choose the type of sensor(Normal sensor/home sensor/delay sensor/24 hour sensor [Enter) , press ].e)Activate the wireless sensor within 30s,the control panel will sound a beep ,and the LCD will show “ ”.if the wireless sensor Add OK,RFID tag 01-50already has been added before ,the control panel will sound 2 beeps and the LCD will show “already exists”What is Normal Sensor/Home sensor/24 hour sensor/Delay sensor? Normal Sensor: In arm mode, when normal sensors are triggered, system will alarm. In disarm mode, when normal sensors are triggered, system will not alarm.Home Sensor: In home mode, only normal sensors will be triggered and home sensors will not be triggered while alarming ,this will allow user to move freely at home.DeleteDelete a RFID taga)Log on setting menu, ,choose “Accessories”,press r].[Enteb) , choose “RFID tag”, press . [Enter]c) , choose “Delete one”, press .[Enter]d)Enter the remote control number(01-50) you want to delete.the control panel will sound a beep if delete succeeded. Delete all remote control&keypada)Log on setting menu, choose “Accessories”, press [Enter].b) , choose “RFID tag”, press . [Enter]c) , choose “Delete all”, press .[Enter]d)Enter “1” delete all the added RFID tag,the control panel will sound a beep if delete succeeded.(4).Test modeTest mode enables you to check whether the remote/RFID tag/wireless sensor has been added successfully.a)Log on setting menu, ,choose “Accessories”, press .[Enter]b) , choose “test mode”, press .[Enter]c)Trigger the accessories you have added before,24 Hour Sensor: Regardless the system is armed or disarmed, when 24 hour sensors are triggered, system will alarm at once.Delay Sensor: In arm mode, when delay sensors are triggered, system will alarm after the entry delay time you have set. (please refer to the Entry delay instruction on page 32).*When you add more wireless sensors ,the wireless sensor number will add 1 automatically from 01 to 50.DeleteDelete a wireless sensora)Log on setting menu, ,choose “Accessories”,press . [Enter]b) , choose “wireless sensor”, press ].[Enterc) , choose “Delete one”, press .[Enter]d)Enter the wireless sensor number(01-50) you want to delete .the control panel will sound a beep if delete succeeded.Delete all wireless sensorsb)Log on setting menu, ,choose “Accessories”, press . [Enter]b) , choose “wireless sensor”, press .[Enter]c) , choose “Delete all”, press . [Enter]d)Enter “1” delete all the added wireless sensor ,the control panel will sound a beep if delete succeeded.press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-9.png)
![15 16(1)Date and Timea)Log on setting menu, ,choose “System setting”, press [Enter].b) , choose “Date and Time”, press ]. [Enterc) to move the pointer ,input current date and time, press to save. [Enter](2)Entry/Exit delayEntry delayEntry delay gives you time to disarm the system upon entry, before an alarm occurs. only the delay sensors are invalid, the non delay sensors will be triggered normally.Log on the menu, , choose “System Settings”, press .[Enter]a) , choose “Entry Exit Delay”, press . [Enter]b) , choose “Entry Delay”, press . [Enter]c)Input time for entry delay; press to save. [Enter]Exit delayExit delay gives you time to exit after arming.a)Log on the menu, , choose “System Settings”, press .[Enter]b) , choose “Entry Exit Delay”, press .[Enter]c) , choose “Exit Delay”, press . [Enter]d)Input time for exit delay; press to save.[Enter] *Entry/exit delay time is calculated in seconds; default is 0 second (off); the range is 0-300 seconds.(3)Auto Arm/DisarmYou can set up the system to arm/disarm automatically at a defined time every day.3.System settings Timing to Arma)Log on the menu, , choose “System Settings”, press .[Enter]b) , choose “Auto Arm/Disarm”, press .[Enter]c) , choose “Auto Arm Time”, press .[Enter]d)Input exact time for arming; press . [Enter]Timing to disarma)log on the menu, , choose “System Settings”, press to confirm.[Enter]b) , choose “Auto Arm/Disarm”, press .[Enter]c) , choose “Auto Disarm Time”, press . [Enter]d)Input exact time for disarming; press .[Enter](4)Control by phone callMethod 1When an alarm is triggered ,the control panel will dial the stored phone numbers ,after picked up ,you can follow the voice promotion to remote control the panelMethod 2a) Dial the telephone number of control panel ,either the number of SIM card in the control panel or the number of landline to which the control panel is connected, after got through ,the voice promotion will guide you to enter access code.b) Enter access code(user code),press " " to confirm.#c) Follow the voice promotion to remote control the panel.Remote Phone Control Instruction TablePhone Buttons Function ExplanationPress [ ]Press [ ]Press [ ]Press [ ]Press [ ]Arm the systemDisarm the systemMonitor on siteTurn on sirenTurn off sirenArm succeedDisarm succeedPress [*] to prolong monitor timeDeter the intrudersSiren stops ringingPress [ ]To exit Remote Phone Control Or hang up the phonepress or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-10.png)
![17 18a) Log on the menu, ,choose “System Settings”, press [Enter].b) , choose “Control by phone”, press .[Enter]c) , choose “on” to turn on this function ,choose “off” to turn off this function, press to confirm [Enter]5)Line cut alarmWhen line cut alarm function is on, the control panel will alarm once the PSTN land line is cut or pulled out even if the built-in siren was set to mute.Turn on/off Line cut alarma)Log on the menu, ,choose “System Settings”, press [Enter] b) , choose “Line cut alarm”, press .[Enter]c) , choose “on” to turn on this function or choose “off” to turn off this function, press [Enter] to confirm.6)GSM fail tipNotification of GSM signal.a)Log on the menu, , choose “System Settings”, press [Enter]b) , choose “GSM fail tip”, press .[Enter]c) , choose “on” to turn on this function or choose “off” to turn off this function, press to confirm.[Enter]7)Keypad TonesActivate or deactivate the sound when typing on the keypad of control panea)Log on the menu, , choose “System Settings”, press [Enter] b) , choose “Keypad Tones”, press .[Enter]c) , choose “on” to turn on this function or choose “off” to turn off this function, press to confirm.[Enter]8)Access codeThe control panel has 3 types of access code, user code, admin code and duress code. Please change all codes before using.press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]Admin CodeYour admin code enables you to enter setting menu.a)Log on the menu, ,choose “System Settings”,press .[Enter]b) , choose “Access Code”, press .[Enter]c) , choose “Admin Code”, press .[Enter]d)LCD display will show “Input 6 Digits”, then input 6 digits for code, press [Enter].(Default Admin Code: 123456)Input the new admin code, press .[Enter]User CodeYour user code enables you to arm/disarm the system on control panel ,and it is the access code requested when call the alarm control panel.a)Log on the menu, ,choose “System Settings”,press .[Enter]b) , choose “Access Code”, press .[Enter]c) , choose “User Code”, press .[Enter]d)LCD display will show “Input 4 Digits”, then input 4 digits for code, press [Enter].(Default User Code: 1234)Input the new user code, press .[Enter]Duress CodeIn case of emergency, when user is requested to disarm the system by force, it's recommended to use the duress code to disarm the alarm system. The panel will silently dial the stored telephone numbers.a)Log on the menu, ,choose “System Settings”,press .[Enter]b) , choose “Access Code”, press .[Enter]c) , choose “Duress Code”, press .[Enter]d)LCD display will show “Input 4 Digits”, then input 4 digits for code, press [Enter].Default Duress Code: 0000)Input the new duress code, press .[Enter]Open Door CodeThis code is used to open the connected electronic lock.a)Log on the menu, ,choose “System Settings”,press .[Enter]b) , choose “Access Code”, press .[Enter]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-11.png)
![19 20c) , choose “Open Door Code”, press .[Enter]d)LCD display will show “Input 4 Digits”, then input 4 digits for code, press [Enter].Default Duress Code: 8888)Input the new Door Open Code, press .[Enter]9)Ring timesThis function enables you to determine the number of times the control panel will ring before taking the phone call.a)Log on the menu, , choose “System Settings”,press [Enter].b) , choose “Ring time”, press .[Enter]c)Input 0~9,press to save[Enter]10)Siren setupWired sirenWired siren is connected to the control panel by wire.Turn On/Off Wired Sirena)Log on the menu, ,choose “System Settings”, press .[Enter]b) , choose “Siren Setup”, press .[Enter]c) , choose “Wired Siren”, press .[Enter]d) , choose “On” or “Off” to turn the wired siren to ON or Off, press [Enter].Built in sirenBuilt in siren is inside of control panel.Turn On/Off built in sirena)Log on the menu, ,choose “System Settings”, press .[Enter]b) , choose “Siren Setup”, press .[Enter]c) , choose “Built in siren”, press .[Enter]d) , choose “On” or “Off” to turn the built in siren to ON or Off, press .[Enter]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]Wireless sirenWireless siren is connected to control panel through radio.Turn On/Off wireless sirena)Log on the menu, ,choose “System Settings”, press .[Enter]b) , choose “Siren Setup”, press .[Enter]c) , choose “wireless siren”, press .[Enter]d) , choose “On” or “Off” to turn the wireless siren to ON or Off, press .[Enter]Set ringing time for all sirensa)Log on the menu, ,choose “System Settings”, press [Enter]b) , choose “Siren Setup”, press .[Enter]c) , choose “Siren Alert Time”, press .[Enter]d)Input the ringing time, press .[Enter]*Siren ringing time is calculated in minutes, default setting is 3 mins ,if you set the time to 0,the siren will not ring out.press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ](11)Connect to CMSPlease ignore this step if users don't need to connect to CMS center.This alarm control panel is full compatible with Contact ID ,when connected to CMS center, control panel will upload contact ID to CMS centerautomatically once the system is triggered.First you sure store the CMS phone number and User ID to the alarm control panel ,which are provided by CMS. Please refer to the instruction of alarm phone number setting for setting the CMS phone number.User ID settinga)Log on the menu; ,choose “System Settings”, press .[Enter]b) ,choose “User ID”, press . [Enter]c)LCD display will show “Input 4 Digits”, input 4 digits user ID, press .[Enter]press or [ ] [ ]press or [ ] [ ]](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-12.png)
![21 22Upload Arm/ Disarm Report to CMS CenterWhen this function is enabled, all arm/disarm reports will be uploaded automatically to CMS so that CMS center can know the status of the alarm system.Turn On/Off Arm/Disarm uploada)After the User ID is set, Log on the menu; , choose “System Settings”, press .[Enter]b) , choose “Arm upload” or "disarm upload", press .[Enter]c) ,choose "On" or "Off" to turn Arm/Disarm upload to On or Off.press or [ ] [ ]press or [ ] [ ]press or [ ] [ ](12)Call recycleThe call recycle enables you to set the number of times the control panel attempts to dails the stored alarm phone numbers.a)Log on the menu, , choose “System Settings”, press . [Enter]b) , choose “Call recycle”, press .[Enter]c)Input the number[0-9], press .[Enter](13)Backlight timeUser can set standby time of the backlight from 0 to 300s.a)Log on the menu, ,choose “System Settings”, press .[Enter]b) ,choose “Backlight Time”, press .[Enter]c)Input time for backlight time; press .[Enter]Backlight time is calculated in seconds; default is 30 seconds.(14)Reseta)Log on the menu, , choose “System Settings”, press .[Enter]b) , choose “Reset”, press to reset the system to default [Enter]setting.Note: All system settings will be restored to default setting. Reset will not delete the accessoriesthat has already coded to the control panel.(15)LanguageBy default the language of alarm control panel is set to English.a)Log on the menu, , choose “System Settings”, press .[Enter]b) , choose “Language”,press [Enter]c)Choose the language you wish to change to ,press to save.[Enter]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]press or [ ] [ ]4.HistoryUsers can check the event logs freely,150 event logs are traceable.a)Log on the menu, , choose “History”, press [Enter].b) to check the event logs.press or [ ] [ ]press or [ ] [ ]](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-13.png)
![27 28ArmPress the button, the system enters [Arm ] arm state when one beep is heard and the arm LED on the control panel is on.Note: If Exit Delay is activated, all zones except the 24-hour zone will enter arm state after the set delay time.Delete/EditYou can swipe left the added control panel to delete or tap the control panel to edit. Turn On/Off passwordYou can tap the lock button to turn On/Off the password, after that you should enter password to logon. Tap to turn On/Off passwordOperation guidance1.Tap the alarm control panel you added to enter into the main page of APP ,you can slide between the pages.2.Under the fist page ,you can Arm ,Disarm, Home Arm the sytem ,and send a voice memo or Two way talk request to alarm panel.3.Under the second page ,you can program the phone number and SMS number of alarm ,change the zones name and RFID tag notification name ,and send a status inquiry command to alarm panel4.Under the third page ,can you set the Entry&Exit delay time ,build-in siren volume and ring time ,modify the disarm password ,change the language and reset the alarm panel to factory setting.AccssoriesRemote controlThe remote control is dainty and delicate, easy to carry. It can be attached to your key ring, or just put into your pockets or purses.When you are about to exit or entry the house, you can use it to arm or disarm the system. In case othe panic button, the alarm will be activated immediately.ArmDisarmStayPanicLED Indicator](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-16.png)
![The window/door sensor can be installed on doors, windows, and any other objectsthat can open and close. The sensor transmits signals to the control panel when a magnet mounted near the sensor is moved away. LED IndicationBlinks once Door/Window ContactDoor/Window contact is triggered29 30DisarmPress the button on the remote [Disarm ]control, the system enters disarm state when two beeps are heard and the disarm LED on the control panel is on.When alarm is activated, the siren will hoot. Press the button, the system is [Disarm ]disarmed . But the LED indicator of triggered zone keeps flashing for further checking. Press button again, the alarming [Disarm ]zone indicator goes out.Home Arm (Part Arm)Press button on the remote control, [Stay ]the system enters home mode when one beep is heard and the home mode LED is on. All the normal sensors are armed except the home mode sensors which are disarmed, so that users can move freely at home.Panic buttonWhenever you press the panic button on the remote control, the system will alarm immediately.LED Status IndicatorTransmitter MagnetPCB Layout12V 23A batteryPCB boardLED Meaning](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-17.png)
![emove the back coveroperly.f 1 cm. f the transmitter and magnet. Make sure the . Make f the transmitter. Secure the transmitter and ed locations with double-sided tapes or screws.operly on the desired s when . Purchase dedicated logic control processing technology and intelligent analysis algorithm, effective resolution of interfering signal and human movement eventing false alarm. It features automatic temperature compensation and resistance to flow technology, adapting to environmental and temperature for halls, hallways, etc. change. It can detect human movement within the 8-meter cone space, suitable signal, prTestInstallationPIR Motion Detector543LED IndicationPCB Layout1. Press the back cover and slide down to r .2. Remove the insulating strip. The contact works immediately.3. Press the button on the remote control. The system switches to the arm [Arm ] status. Separate the transmitter and magnet. The LED is on and the panel alarms. It indicates that the sensor works prNote: There are triangle marks on the side otriangle marks face each other and within the range oNote: Make sure the transmitter and magnet works prlocations. If a metal door is installed, place spacers under the transmitter and magnet. Do not apply the contact to a rolling shuttercontacts for rolling shutternecessary.Mount the transmitter on the frame and the magnet on the door or windowsure the magnet is on the right side omagnet on the desirThe detector adopts digital1. Detecting lens2. LED3. Snap joint4. Test button5. Installation bracketBlinks continuously: Under self-testing state.Blinks once: Intruder is detected.Blinks twice: 3 minutes testing is finished, enters power saving mode.Blinks once per 3 seconds: Low battery indication, LCD shows: Sensor 1-50(Sensor Name) low battery, please change the batteries immediately.Note: If the detector is disassembled,system will sound immediately,and LCD shows "Sensor 1-99(Sensor Name) Sensor Tamper".21AA 1.5V LR6AA 1.5V LR6LED ON / OFF Infrared sensorInfrared sensor Zone settingTamper switch31 32](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-18.png)
![s y 10 y without . At this emains sleeping.ecommended that oom, the system alarms Test3. Trigger the alarmWorking ModeTesting modeAfter self-testing, the detector entertesting mode, and detects once every 10 seconds. After 3 minutes, the LED blinks twice, and the detector enters power saving mode.Hold the test button and load the battery, then release the test button, the detector stands in testing mode, it keeps detecting once everseconds. Exits this status by reloading the batterholding the test button.Power saving modePress the buckle to open the back cover. Remove the insulating strip. After 30-second self-testing, the detector switches to the testing mode. 1. Remove the insulating stripPress the button on the [Arm ]remote control. The system is in the armed state.2. Arm Keep pressing the test button at the back until the siren sounds.Note: The testing mode sustains for 3 minutes. Then, the LED blinks twice, indicating the detector is in the power saving mode. The product features power-saving design. If the detector detects human movement twice in 3 minutes, it will switch to the sleeping state to save powertime, the LED will not blink and no alarm. After no movement within the next 3 minutes, the detector switches back to the working state automatically.Sleep after detecting human movement twiceNote: After the detector is in the sleeping state, ensure no human movement within 3 minutes; otherwise, the detector rIn the sleeping state, it is ryou leave the room after arming the system. Ensure no human movement in 3 minutes. Then, go into the rimmediately.Case 2: Press the test button and then arm.Case 1: Initial start and then arm.3 minutes laterNo human movement within 3 minutesSwitch from sleep to arm.33 34](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-19.png)
![FAQ Phenomena Cause of Malfunction Troubleshoot MethodNo response from control panel operationAccessories cannot connect to control panelNo response from the control panel by operating remote control Power switch is offAC Power failureLithium battery backup power exhausted Panel not in learning statusAccessories not triggered for learningThe control panel has different radio frequency with accessories Remote control is not learned to control panelOpen battery compartment, turn on the powerContact local main power supply bureau Connect to main power with adapterMake sure the panel set in learning statusMake sure the triggered accessories transmitting signal to panel for learning Follow the manual and connect the remote control to panelOut of range between remote control and panelRemote control the panel in proper distanceSignal repeater could be added Please contact retailer for helpRFID card/tag fail to disarmTouch keyboard fail to make related settingRFID card/tag not connected to the panelNot logged onto the setting menu Follow the manual and connectRFID card/tag to the panelInput the correct admin code,press [Enter] and log on menu settingNo response after inserting a SIM cardThe direction of the SIM card is not correctSwitch on the control panel first and then insert the SIM cardThe SIM card is not a GSM SIM cardPlease insert the SIM card again according to the user manualInsert the SIM card first and then switch on the control panelPlease use GSM SIM cardAPP replied" Return data run out" Please check the network of control panel and mobile phone Make sure the network works properlyAPP replied "Control panel offline" Please check the network of control panel Make sure the SIM card of control panel is not indebtedSpecificationsControl PanelWireless Remote ControlPower Supply Alarm Current Transmitting Distance Radio Frequency Housing Material Operating Condition Dimensions (L x W x H) DC 3V (CR2025 Lithium Battery x 1pc)< 7mA< 80m (in open area)315MHz or 433.92MHz (± 75KHz) ABS plasticTemperature -10°C ~+ 55°CRelative Humidity < 80% (non-condensing)58 x 31 x 9.5mmPower SupplyStandby Current Alarm Current Backup Battery Internal Siren Volume Radio Frequency Maximum Stored Phone No. Maximum Remote Controls Maximum Sensors Maximum RFID Tags Maximum Event Logs Housing Material Operating Condition Dimensions (L x W x H) Input DC 12V 500mA, 6Wh < 90mA< 300mABL-5B 3.7V 800mAh rechargeable lithium battery x 2 pcs100dB315MHz or 433.92MHz (±75KHz)5 alarm phone numbers and 2 CMS numbers150 eventsABS plasticTemperature -10°C ~+55 °CRelative Humidity < 80% (non-condensing) 203 x 117 x 25mm41 4230 pcs99 pcs99 pcs](https://usermanual.wiki/Security-Group/SSG-T6/User-Guide-3245623-Page-23.png)
