Seiko Epson AE-WLU5000 Wireless LAN Module User Manual Statement FCC 20160421

Seiko Epson Corporation Wireless LAN Module Statement FCC 20160421

Contents

Users Manual (Statement)

Download: Seiko Epson AE-WLU5000 Wireless LAN Module User Manual Statement  FCC   20160421
Mirror Download [FCC.gov]Seiko Epson AE-WLU5000 Wireless LAN Module User Manual Statement  FCC   20160421
Document ID3014785
Application IDMB2/JBlhmyY71O1RcMlRlw==
Document DescriptionUsers Manual (Statement)
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize0.86kB (10768 bits)
Date Submitted2016-06-02 00:00:00
Date Available2016-06-02 00:00:00
Creation Date2016-05-24 17:55:04
Producing SoftwareGPL Ghostscript 9.04
Document Lastmod2016-05-24 17:55:04
Document TitleStatement _FCC __20160421
Document CreatorPDFCreator Version 1.2.3
Document Author: kelelee

Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter
or antenna.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the
following: “Contains FCC ID: BKMAE-WLU5000”. The grantee's FCC ID
can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
Producer                        : GPL Ghostscript 9.04
Keywords                        : ()
Modify Date                     : 2016:05:24 17:55:04+08:00
Create Date                     : 2016:05:24 17:55:04+08:00
Creator Tool                    : PDFCreator Version 1.2.3
About                           : 326d2ec5-23f1-11e6-0000-fc7be71948c..›.2016-05-24T17:55:04+08:00
Document ID                     : uuid:326d2ec5-23f1-11e6-0000-fc7be71948cŸ3c..
Format                          : application/pdf
Title                           : Statement _FCC __20160421
Creator                         : kelelee
Description                     : ()
Author                          : kelelee
Subject                         : 
EXIF Metadata provided by EXIF.tools
FCC ID Filing: BKMAE-WLU5000

Navigation menu