Seiko Epson FBM291A Bluetooth Interface Board User Manual Bluetooth Interface Board User s Manual
Seiko Epson Corporation Bluetooth Interface Board Bluetooth Interface Board User s Manual
Contents
- 1. User Manual
- 2. 04 User Manual
04 User Manual
Bluetooth Interface Board User’s Manual
1
Bluetooth Interface Board User’s Manual
Rev.02 / Nov-08-2017
Features
The Bluetooth Interface board has the following features:
1) A built-in Bluetooth module
2) Bluetooth 2.1+EDR compatible
3) Power class: Class 2
4) External dimensions: 40 mm × 43 mm
Manufacturer: Seiko Epson Corporation
Model Name: M291A
Product Name: Bluetooth Interface board
Integration to the end product
The Bluetooth Interface Board has to be installed and used in accordance with the technical
description/installation instructions provided by the manufacturer.
The system may only be implemented in the configuration that was authorized. Note that
any changes or modifications to this equipment not expressly approved by the manufacturer
could void the user’s authority to operate this equipment.
Labelling
The Bluetooth Interface board labelled as below.
FCC ID: BKMFBM291A
IC: 1052C-M291A
The proposed FCC ID/IC labels format are to be placed on the module. If FCC ID/IC are not
visible when the module is installed into the system, “Contains FCC ID: BKMFBM291A” and
“Contains IC: 1052C-M291A” shall be placed on the outside of final host system.
Bluetooth Interface Board User’s Manual
2
Regulatory Information
FCC/IC Caution
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
This device complies with part 15 of FCC Rules and Industry Canada’s licence-exempt
RSSs. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Le présent appareil est conforme à la partie 15 des règles de la FCC et aux normes des
CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'appareil doit accepter tout brouillage subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
Bluetooth Interface Board User’s Manual
3
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of
the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF
energy that are deemed to comply without testing of specific absorption rate (SAR).
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC
lignes directrices d'exposition et d’exposition aux fréquences radioélectriques (RF)
CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée
conforme sans évaluation du débit d’absorption spécifique (DAS).
Instructions to OEM Integrators
If other radio devices are to be integrated with this module, an additional evaluation and
FCC/IC submission may be required. Integrators are responsible for such additional
evaluation and FCC/IC submission.