Seiko Epson FBWLU6320 2.4GHz Wireless LAN MINI USB module User Manual Install
Seiko Epson Corporation 2.4GHz Wireless LAN MINI USB module Install
Contents
- 1. User Manual (Statements).pdf
- 2. User Manual.pdf
User Manual (Statements).pdf
USA - Federal Communications Commission (FCC)
FCC Radiation Exposure Statement
Interference Statement
These devices comply with Part 15 of the FCC Rules. Operation of the devices
is subject to the following two conditions: (1) The devices may not cause
harmful interference, and (2) The devices must accept any interference that
might cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If the equipment is not installed and used in accordance with
the instructions, the equipment might cause harmful interference to radio
communications. There is no guarantee, however, that such interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception (which can be determined by
turning the equipment off and on), the user is encouraged to try to correct the
interference by taking one or more of the following measures:
Relocate this device.
Increase the separation between the device and the receiver.
Connect the device into an outlet on a circuit different from that of other
electronics.
Consult the dealer or an experienced radio technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the following:
“Contains FCC ID: BKMFBWLU6320”. The grantee's FCC ID can be used only
when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.
Canada. Industry Canada (IC)
This device complies with RSS210 of Industry Canada.
CAUTION: Exposure to Radio Frequency Radiation. The installer of this radio
equipment must ensure that the antenna is located or pointed such that it does
not emit RF field in excess of Health Canada limits for the general population.
Consult Safety Code 6, obtainable from health Canada’s website
www.hc-sc.ca/rpb.
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions
suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec
un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada authorization
is no longer considered valid and the IC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne
peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM
sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une
autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains IC:
1052C-WLU6320”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où
l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue
entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit
visible avec l'inscription suivante: "Contient des IC: 1052C-WLU6320".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de
l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires
requises et avertissements comme indiqué dans ce manuel.
This device is intended only for OEM integrators under the following conditions:
(For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les
conditions suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée
entre l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
Europe. EU Declaration of Conformity
This equipment complies with the essential requirements of the European
Union directive 1999/5/EC.
Български
С настоящето SEIKO EPSON CORPORATION потвърждава, че това
Безжично устройство е в съответствие със задължителните изисквания и
другите приложими разпоредби на Директива 1999/5/EC.
Čeština
SEIKO EPSON CORPORATION tímto prohlašuje, že tento Wireless Device je
ve shodž se základními požadavky a dalšími príslušnými ustanoveními
smernice 1999/5/ES.
Dansk
Undertegnede SEIKO EPSON CORPORATION erklæ rer herved, at følgende
udstyr Wireless Device overholder de væ sentlige krav og øvrige relevante krav
i direktiv 1999/5/EF.
Deutsch
Hiermit erklärt SEIKO EPSON CORPORATION, dass sich das Gerät Wireless
Device in Ü bereinstimmung mit den grundlegenden Anforderungen und den
übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
English
Hereby, SEIKO EPSON CORPORATION declares that this Wireless Device is
in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Eesti
Käesolevaga kinnitab SEIKO EPSON CORPORATION seadme Wireless
Device vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
Español
Por medio de la presente SEIKO EPSON CORPORATION declara que el
Wireless Device cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eλληυικά
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ SEIKO EPSON CORPORATION ΔΗΛΩΝΕΙ ΟΤΙ Wireless
Device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ
ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
Par la présente SEIKO EPSON CORPORATION déclare que l'appareil
Wireless Device est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Italiano
Con la presente SEIKO EPSON CORPORATION dichiara che questo
Wireless Device è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Íslensk
Hér með lýsir SEIKO EPSON CORPORATION yfir Þ ví að Wireless Device er í
samræ mi viðgrunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Latviešu
Ar šo SEIKO EPSON CORPORATION deklarē, ka Wireless Device atbilst
Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem
noteikumiem.
Lietuvių k.
Šiuo SEIKO EPSON CORPORATION deklaruoja, kad šis Wireless Device
atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Magyar
Alulírott, SEIKO EPSON CORPORATION nyilatkozom, hogy a Wireless
Device megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC
irányelv egyéb elõírásainak.
Maltese
Hawnhekk, SEIKO EPSON CORPORATION, jiddikjara li dan Wireless Device
jikkonforma mal-ħtiġijiet essenzja ma provvedimenti oħrajn relevanti li hemm
fid-Dirrettiva 1999/5/EC.
Nederlands
Hierbij verklaart SEIKO EPSON CORPORATION dat het toestel Wireless
Device in overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
Norsk
SEIKO EPSON CORPORATION erklæ rer herved at utstyret Wireless Device
er i samsvar med de grunnleggend krav og øvrige relevante krav i direktiv
1999/5/EF.
Polski
Niniejszym SEIKO EPSON CORPORATION oświadcza, że Wireless Device
jest zgodny z zasadniczymi wymogam oraz pozostałymi stosownymi
postanowieniami Dyrektywy 1999/5/EC.
Português
SEIKO EPSON CORPORATION declara que este Wireless Device está
conforme com os requisitos essenciais e outras disposições da Directiva
1999/5/CE.
Română
Prin aceasta, SEIKO EPSON CORPORATION declară că acest Dispozitiv
Wireless este în conformitate cu cerinţ esenţiale şi alte dispoziţii relevante ale
Directivei 1999/5/CE.
Slovenčina
SEIKO EPSON CORPORATION týmto vyhlasuje, že Wireless Device spĺňa
základné pošiadavky a všetky prĺsluš ustanovenia Smernice 1999/5/ES.
Slovenščina
SEIKO EPSON CORPORATION izjavlja, da je ta Wireless Device v skladu z
bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
Suomi
SEIKO EPSON CORPORATION vakuuttaa täten että Wireless Device
tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Svenska
Härmed intygar SEIKO EPSON CORPORATION att denna Wireless Device
står I överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
France
In all Metropolitan départements, wireless frequencies can be used under the
following conditions, either for public or private use:
Indoor use: maximum power (EIRP) of 100 mW for the entire
2400–2483.5 MHz frequency band.
Outdoor use: maximum power (EIRP) of 100 mW for the 2400–2454 MHz
band and with maximum power (EIRP) of 10 mW for the 2454–2483.5
MHz band.
Taiean NCC Statement
以下警語適用台灣地區
1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得
擅自變更頻率、加大功率或變更原設計之特性及功能。
2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現
象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依
電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科
學及醫療用電波輻射性電機設備之干擾。
3. Note: 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2.
系統廠商應於平台上標示「本產品內含射頻模組: XXXyyyLPDzzzz-x
(NCC ID) 」字樣