Select Comfort 1000G Adjustable Foundation Remote User Manual

Select Comfort Corp Adjustable Foundation Remote

User Manual

7Remote Control FunctionA Low Battery If low battery indicator is lit up, batteries need to be changed.B Remote Troubleshooting Pressing and holding both Head Massage Down button and Foot Massage Down button for 3 seconds will force the remote into a self-test mode. If LCD displays either “1” or “2” error code, the remote needs to be replaced. 1 – Radio error 2 – Battery circuit error C Position Timer Press to set the current position timer in 15-minute increments up to 180 minutes. Once it reaches 180 minutes, the next increment goes back to 0. Once timer has expired, the foundation will return to the flat position. If a position other than flat is desired, press and hold Custom Preset 1 as you set the position timer. Once the timer has expired, the foundation will return to the Custom Preset 1 position. D Massage Timer Press to set the current massage timer in 15-minute increments up to 180 minutes. Once it reaches 180 minutes, the next increment goes back to 0. Massage timer does not activate the massage feature. Once massage feature is activated and massage timer has expired, the massage feature will stop. Activating the massage timer and setting it to 0 will not turn off the massage.E Custom Preset 1 Press and hold for more than 3 seconds to set current position or function (massage or wave) as the programmed position and/or function. The LCD display will show “1” to indicate that the position and/or function has been set. Press Custom Preset 1 to return the bed to the custom programmed position and/or function. LCD display will show “1” and bed animation of both head and foot sections.F Raise Head/Lower Head Press and hold to raise or lower the head section to reach desired position. LCD will display animation of the head section. G Raise Foot/Lower Foot Press and hold to raise or lower the foot section.H Lounge Press Lounge – the head and foot sections rise to a lounge position. LCD will display bed animation of both head and foot sections.I Flat Press Flat – the head and foot sections go to the flat position and both massage and position timers reset to 0. Pressing the Flat button will automatically turn off all massage features.J Zero Gravity Press Zero Gravity – the head and foot sections raise to 7 degrees.K Head Massage Press and hold for more than 3 seconds to turn the head massage feature on or off. Press the up arrow to increase massage intensity; press the down arrow to decrease massage intensity. LCD display will light up.L Wave Massage Press and hold for more than 3 seconds to turn the wave massage feature on or off. Press the up arrow to increase massage intensity; press the down arrow to decrease massage intensity. LCD display will light up.M Foot Massage Press and hold for more than 3 seconds to turn the foot massage feature on or off. Press the up arrow to increase massage intensity; press the down arrow to decrease massage intensity. LCD display will light up.FlexFit Plus™ Adjustable BaseECFHKLBADGIJM
8Remote Control FunctionFlexFit™ Adjustable BaseA Raise Head/Lower Head Press and hold to raise or lower the head section to reach desired position. LCD will display animation of the head section. B Custom Preset 1 Press and hold for more than 3 seconds to set current position as the programmed position. The LCD display will show “1” to indicate that the position has been set. Press Custom Preset 1 to return the bed to the custom programmed position. LCD display will show “1” and bed animation of both head and foot sections.C Raise Foot/Lower Foot Press and hold to raise or lower the foot section.D Flat Press Flat – the head and foot sections go to the flat position. ABCD
9Remote ProgrammingFLAT BUTTONRAISE HEAD BUTTON2 Program One Remote to an Adjustable BaseBefore beginning, make certain the bed is plugged into a working, grounded electrical outlet. Locate the receiver unit (power down box) and press the Learn button on the power down box for 1 second then release. Press and hold both the Flat and Raise Head buttons on the remote simultaneously for more than 5 seconds. The remote LCD display will blink a few times. The LED on the power down box will flash slowly at first then rapidly to indicate that the remote has been programmed to operate a bed.If programming fails, initiate the programming procedure a second time.1 Power Down BoxIn case of a power outage, press and hold the Learn button on the receiver unit (power down box) to lower the bed to the flat position. This function is only for lowering the bed and will not move the bed to any other position. Once the bed is flat replace the (2) 9 volt batteries.
3 Program One Remote Control to Two BedsBefore beginning, make certain the beds are plugged into a working, grounded electrical outlet. Locate the power down box for bed 1 and press the Learn button on the power down box for 1 second then release. Press and hold both the Flat and Raise Head buttons on the first remote simultaneously for more than 5 seconds. The remote LCD display will blink a few times. The LED on the first power down box will flash slowly at first then rapidly to indicate the remote has been programmed to operate the first bed. Repeat these steps with bed 2. One remote is now programmed to operate two beds.If programming fails, initiate the programming procedure a second time.4 Program Two Remote Controls to Two BedsBefore beginning, make certain the beds are plugged into a working, grounded electrical outlet. Locate the power down box for bed 1 and press the Learn button on the power down box for 1 second then release. Press and hold both the Flat and Raise Head buttons on the first remote simultaneously for more than 5 seconds. The remote LCD display will blink a few times. The LED on the first power down box will flash slowly at first then rapidly to indicate the remote has been programmed to operate the first bed.Repeat these steps with remote 2, then locate the power down box for bed 2 and press the Learn button on the power down box for 1 second and re-lease. Repeat all steps for both remotes on both beds.If programming fails, initiate the programming procedure a second time. NOTE: Operate only one (1) remote at a time. Operating two (2) remote at the same time will momentarily block both RF signals and prevent both remotes from functioning.Remote ProgrammingFLAT BUTTONRAISE HEAD BUTTONFLAT BUTTONRAISE HEAD BUTTONREMOTE 1 REMOTE 2
115 Program Two Remotes to a Split-King Adjustable BaseBefore beginning, make certain the beds are plugged into a working, grounded electrical outlet. Locate the power down box for bed 1 and press the Learn button on the power down box for 1 second then release. Press and hold both the Flat and Raise Head buttons on the first remote simultaneously for more than 5 seconds. The remote LCD display will blink a few times. The LED on the first power down box will flash slowly at first then rapidly to indicate the remote has been programmed to operate the first bed.Wait 90 seconds before proceeding to the second remote.Locate the power down box for bed 2 and press the Learn button on the power down box for 1 second then release. Press and hold both Flat and Raise Head buttons on the second remote simultaneously for more than 5 seconds. The remote LCD display will blink a few times. The LED on the second power down box will flash slowly at first then rapidly to indicate the remote has been programmed to operate the second bed. If programming fails, initiate the programming procedure a second time.NOTE: Operate only one (1) remote at a time. Operating two (2) remotes at the same time will momentarily block both RF signals and prevent both remotes from functioning.6 Separate Remote ControlsBefore beginning, make certain the beds are plugged into a working, grounded electrical outlet. Locate the power down box for bed 1 and press the Learn button on the power down box for 1 second then release. Press and hold both Flat and Raise Head buttons on the first remote simultaneously for more than 5 seconds. The remote LCD display will blink a few times. The LED on the first power down box will flash slowly at first then rapidly to indicate the remote has been programmed to operate the first bed.Wait 90 seconds before proceeding to the second remote.Locate the power down box for bed 2 and press the Learn button on the power down box for 1 second then release. Press and hold both Flat and Raise Head buttons on the second remote simultaneously for more than 5 seconds. The remote LCD display will blink a few times. The LED on the second power down box will flash slowly at first then rapidly to indicate the remote has been programmed to operate the second bed. If programming fails, initiate the programming procedure a second time.NOTE: Operate only one (1) remote at a time. Operating two (2) remotes at the same time will momentarily block both RF signals and prevent both remotes from functioning.FLAT BUTTONFLAT BUTTONRAISE HEAD BUTTONRAISE HEAD BUTTONREMOTE 2REMOTE 2REMOTE 1REMOTE 2Warning: Any attempt to make changes or modifications to the remote (e.g. an intentional radiator) could void the user’s authority to operate the remote according to FCC certification (section 15.231).

Navigation menu