Semnox Solutions Private SPRW001 Parafait WIFI Color Reader User Manual Manual
Semnox Solutions Private Limited Parafait WIFI Color Reader Manual
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1723624 |
| Application ID | PRTTDwcrjp7zgNG8lZLMMQ== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | Yes |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 57.77kB (722159 bits) |
| Date Submitted | 2012-06-15 00:00:00 |
| Date Available | 2012-11-25 00:00:00 |
| Creation Date | 2012-06-13 09:49:52 |
| Producing Software | Bullzip PDF Printer / www.bullzip.com / Freeware Edition (not registered) |
| Document Lastmod | 2012-06-13 09:49:52 |
| Document Title | Manual |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | pc1 |
2011 SEMNOX SOLUTIONS PVT LTD Authors: HAJA MOHIDEEN. M VINAYAK KAMATH KIRAN KARANKI [PARAFAIT HARDWARE MANUAL] The Document describes the Introduction of PARAFAIT, Functionality of PARAFAIT HARDWARE and Provide Technical Support. PARAFAIT HARDWARE MANUAL 2011 Table of Contents Introduction ........................................................................................................................ 3 Block Diagram .................................................................................................................... 3 Reader ................................................................................................................................................... 4 Interfacing Board ......................................................................................................................... 10 Interface Board – Game Machine ............................................................................ 14 Installation Process ...................................................................................................... 16 SEMNOX SOLUTIONS PVT LTD. Page 2 PARAFAIT HARDWARE MANUAL 2011 Introduction PARAFAIT is cashless solution for Entertainment centers. The System is 100% Wireless and very low power consumption using advanced technologies. The System has fully-fledged interfacing option which can support any types of machines. Block Diagram GAME MACHINE PARAFAIT SERVER INTERFACING BOARDS WiFy Communication WiFy ACCESS POINTS PARAFAIT READER WiFy Communication SEMNOX SOLUTIONS PVT LTD. Page 3 PARAFAIT HARDWARE MANUAL 2011 Reader Functionality Reader is used to interface between the user, server and the game machine.. It generates the commands necessary to communicate with the Access Point w wirelessly, irelessly, pulses necessary to start the Game Machine and count ount the Ticket Dispensing from Game Machine. Hardware Connection Connectors Descriptions J4 10 Pins FRC Connector from Interfacing Board which has power supply (+5v), Back lilight ght power supply (+10v) and iinterfacing logic signals (connecting to the machine) J5 10 Pins FRC Connector from Configuration Keyboard which is used for Configuring the reader There are two ways to configure the wi wi-fi chip 1. Enter through the reader – This is done by pressing the config buttons appropriately as defined in the Reader Configuration documents. But it has SEMNOX SOLUTIONS PVT LTD. Page 4 PARAFAIT HARDWARE MANUAL 2011 been concluded that this is extremely cumbersome for the users and alternate mechanism has to be developed 2. Enter through setting up the ADHOC network - Adhoc is considered as a point-to-point network in which each wi-fi device is linked directly to every other wi-fi device on the adhoc network. In Adhoc mode the module itself creates an "On Demand" network to which we can connect our computer as we connect other networks. IP Addresses are usually assigned through Auto IP. In our case a. When the wifi device is taken into ADHOC network mode, it’ll setup network parafait_:xx:xx – where xx:xx are the last 4 digits of the MAC Address of the wi-fi chip b. The laptop is used to connect to this ADHOC network. It’ll be assigned an IP in the range 169.254.x.x by the device c. The below specified program will then telnet to the wi-fi device and configure the parameters as entered by the user. Connecting to the Adhoc network from the computer 1. Go to network connections and select view wireless networks. 2. Select the parafait_: XX: XX where XX: XX are the last 4 digits of the MAC Address. a. This will be an open network which does not ask for a pass phrase or pass key. b. It will take some time for windows to auto assign an IP and get connected to the network. The IP address assigned by windows auto IP must be on the subnet 169.254.x.y (this can be checked by going to the command prompt and giving the command ipconfig).Obtaining the ip address in the range(169.254.x.y) ensures that the user has got connected to the ADHOC network. SEMNOX SOLUTIONS PVT LTD. Page 5 PARAFAIT HARDWARE MANUAL 2011 Application Details: 1. Click on the wi-fi configuration application to launch the software. a. As the software loads, a status message will be displayed to the user on the connection status (whether the user is connected to the adhoc network). b. The IP address has been set to 169.254.1.1. Click the connect button. c. The application communicates with the device and if the communication is successful, it will take the device to the command mode and the user will be able to view the parameters which have already been set in the reader. Corresponding messages will be displayed to the user (on the connection status, parameter retrieval status etc.).The MAC address of the device too will be displayed to the user. d. For the parameters retrieved, the user has the option to modify the parameters. e. The user has to enter the parameter in the respective text box and click on the apply button to set the parameter. In order to save the changes, the user has to click the save button so that the changes made by him will be stored in the device permanently. The status messages will be shown to the user after he clicks the save button thereby confirming whether the changes have been saved successfully. f. Once the configuration is completed we need to POWER ON the reader. Setting the device to the ADHOC mode: 1. When the reader loads, hold the DOWN button pressed. Then press the UP button to enter the ADHOC mode. Press the UP button again to enter the ADHOC setup. 2. Once the wifi device enters the ADHOC setup, the following configuration settings will be applied to it. SEMNOX SOLUTIONS PVT LTD. Page 6 PARAFAIT HARDWARE MANUAL Parameter Name Value SSID parafait_:xx:xx Join Channel IP DHCP OFF IP Address 169.254.1.1 IP Net Mask 255.255.0.0 2011 3. Reset the reader. 4. While configuring the parameters from the application, hold the reader in the ADHOC mode. This can be accomplished by holding the DOWN button when the reader loads and then pressing the UP button to enter the ADHOC mode and then pressing the DOWN button again to enter the ADHOC HOLD mode. SEMNOX SOLUTIONS PVT LTD. Page 7 PARAFAIT HARDWARE MANUAL 2011 Application Screenshot: Messages The below gives you the clear information about messages displayed. Messages Normal Price : xx VIP Price : xx Card Read Processing … Balance : XXX.XX Play Game. Enjoy… Descriptions Shows the price of the game. When Card reaches the determined threshold the Card becomes the VIP Customer, which is defined by the Management. Validating the Card Swipe. This indicates that the card has been read and is being validated at the server Have sufficient balance to play game, shows the amount remaining in the card. Game SEMNOX SOLUTIONS PVT LTD. Page 8 PARAFAIT HARDWARE MANUAL machine is activated Card is not valid, please check with the cashier Invalid Card Please Retry Low Balance Please recharge Tickets updated Play your way Time Remaining XX Mins XX Secs Time out Tap card to play Please Tap Card Then feed tickets Time left: XX Secs Tickets counted XX Time Elapsed Tickets counted XX Time left: XX Secs Pls tap card... Check Balance Please tap card Card Read 2011 Card doesn’t have sufficient balance, card needs to recharged. Ticket updated at the server. The tickets are recorded against the card used to play the game. For timer based machines, message gives you the remaining time For timer based machines, message tells you the end of the game. For Ticket Eater, Swipe card to feed the tickets. Please refer the Configuration settings of Reader to set the reader as Ticket Eater. This indicates the time within which the ticket has to be fed after the last ticket. If no tickets are fed, it’s assumed that the tickets have been fed and tickets are updated against the swiped card. For Ticket Eater, Time out for counting the ticket & shows the total ticket count. For Ticket Eater, Time left out to swipe card to load the Counted ticket to server. User has provision to feed the tickets and then swipe the card. Once the last ticket is fed, the reader shows amount of time the user has to tap the card. Otherwise, the tickets counted are abandoned (as there is no card to associate with) For Check Balance, Customer can check the status of the Card. Gives the details of Credits, Courtesy, Bonus, Tickets, Games, Time Remaining. Please contact Semnox to set the reader as Check Balance. For Check Balance, checking the status of the SEMNOX SOLUTIONS PVT LTD. Page 9 PARAFAIT HARDWARE MANUAL 2011 Checking Balance... card at the server. Credits: XX For Check Balance, Balance values of the card. Courtesy: XX Time: XX Games is usually for Technician Card. Tickets: XX Games: XX Interfacing Board Functionality Interfacing Board is used to deliver power & interface needed machine signal to PARAFAIT Reader. Primarily there are three connectors and five switches Switches SW1 to SW5 Connectors J1 to J3 Connectors J1 Connector: Connect Ticket Dispensing signals from the game machine (Activation & Sensor Pulse) J2 Connector: Connect Ticket Dispensing signals from Ticket Dispenser (Activation & Sensor Pulse) J3 Connector: Connect Coin signals from the game machine SEMNOX SOLUTIONS PVT LTD. Page 10 PARAFAIT HARDWARE MANUAL 2011 J4 Connector: Connect the FRC Connector from Reader, which carries the power supply & control signals. Switch SW1: Output Sensor pulse pull ups. This is used to generate the sensor pulse in e-ticket mode. SW2: Input Activation signal pull ups. This is used to reduce the noise in the signal. SW3: Output Activation signal pull ups. This is used for proper termination to Ticket Dispenser in e-Ticket mode. SW4: Input Sensor Pulse signal pull ups. This is used to reduce the noise in the signal. SW5: Output Coin pulse pull ups. This is used to generate the Coin pulse to start the game. Interfacing boards can be configured in 3 ways. 1. Non Redemption Machine: In this configuration Parafait Reader control the Game play when a valid tap happens. The only connection required (apart from the power and ground) is the coin pulse. The coin pulse wire is tapped and connected to the interface board using the connector J3. See below table to get detailed pin description. 2. Redemption Machine: In this configuration Parafait Reader Control the Game plays when valid tap happens & controls the ticket out. Use connectors J1, J2, J3 to interface the machine with interfacing board. See below table to get detailed pin descriptions. 3. Ticket Eater: In this configuration Parafait Reader will function as ticket eater and count the tickets and load to the respective card. Use connectors J1 & J2 to interface the machine with Interfacing Board. See below table to get detailed pin descriptions. SEMNOX SOLUTIONS PVT LTD. Page 11 PARAFAIT HARDWARE MANUAL 2011 Hardware Connection Connectors Pin Details J1 1 -> Activation Signal (Input to ticket dispenser from machine) 2 -> Ground 3 -> 12Volt 4 -> Sensor Pulse Signal (output from ticket dispenser to machine) 5 -> NC J2 1 -> Activation Signal (Input to ticket dispenser from machine) 2 -> Ground 3 -> 12Volt 4 -> Sensor Pulse Signal (output from ticket dispenser to machine) 5 -> NC J3 1 -> 12 Volt 2 -> Coin Pulse 1 3 -> Ground 4 -> Coin Pulse 2 5 -> 5 Volt J4 1 -> 5 Volt 2 -> Ground 3 -> Backlight (10 Volt) 4 -> Activation Input 5 -> Sensor Input 6 -> Sensor Pulse Output( In e-Ticket Mode) Descriptions For Ticket Interface, disconnect the ticket dispenser from the machine. Connect the machine signal to J1. For Ticket Interface, disconnect the ticket dispenser from the machine. Connect the ticket dispenser signal to J2. For Coin interface, Connect the coin signal to coin pulse 1 & coin pulse 2 is optional. 5 Volt is optional which we can use for Parafait Reader with Character Display, Please don’t use for color display. Crimp FRC 10 Pin cable with FRC Crimping standard( Arrow on the FRC Female connector denote the first pin, So on both side 1st wire of the cable should connect SEMNOX SOLUTIONS PVT LTD. Page 12 PARAFAIT HARDWARE MANUAL 2011 to 1st pin of FRC Female Connector. Crimping reverse will damage the Reader) 7 -> Ticket Mode 8 -> Coin Pulse 9 - > Ground 10 -> 5 Volt Activation Signal MACHINE TICKET DISPENSER Sensor Pulse Signal Configuration Settings Switch settings are used to configure the different types of machines to Parafait Interfacing Board. Depends on the machine signals need to set switch setting on the interfacing board. Below table will give a brief description on the Switch Settings. Switch SW1 Switch Details 1 -> 5 Volt pull up 2 -> 12 Volt pull up SW2 1 -> 12 Volt pull up 2 -> 5 Volt pull up 3 -> Pull down (Connected to ground through 10K) 4 -> Pull down (Connected to ground through 4.7K) SW3 1 -> 12 Volt pull up 2 -> 5 Volt pull up 3 -> Pull down (Connected to ground through 10K) Descriptions For e-Ticket, Parafait Reader will generate the Sensor Pulse for machine. Check the voltage level of the Sensor Pulse by default & use the respective pull up. To isolate the noise in Activation Signal. When board is configured in Non Redemption machine SW2.2 should be set, so that Activation Signal will be terminated properly. In e-Ticket mode the ticket dispenser will be open so to terminate set the switch. Check the Activation Signal by default SEMNOX SOLUTIONS PVT LTD. Page 13 PARAFAIT HARDWARE MANUAL SW4 SW5 4 -> Pull down (Connected to ground through 4.7K) 1 -> 12 Volt pull up 2 -> 5 Volt pull up 3 -> Pull down (Connected to ground through 10K) 4 -> Pull down (Connected to ground through 4.7K) 1 -> 5 Volt pull up 2 -> 12 Volt pull up 3 -> Short to Ground 4 -> Short to Ground 2011 & use the respective pull up. To isolate the noise in Sensor Pulse. When board is configured in Non Redemption machine SW2.2 should be set, so that activation signal will be terminated properly. To generate correct Coin pulse set this switch. Check the default voltage level of the coin pulse. For ex: For coin logic active low signal on the SW5.3 or SW5.4. When the switches are TURNED ON Coin Pulse 2(J3.4) shouldn’t be connected, and Vice -versa. Interface Board – Game Machine Below section details how the interface board needs to be connected to the game machine. There are two scenarios 1. Coin machine (non ticket) – Here the objective is to generate the coin pulse so that the game machine starts operating. 2. Redemption machine (ticket) – Beyond generating the coin pulse, the ticket dispensing needs to be handled. This needs to handle two modes of operation a. Physical mode – Here the machine dispenses physical tickets. This needs to be counted by the Parafait system b. E-Ticket mode – Here the machine will not dispense physical tickets. We need to give appropriate pulses to the game machine so that the game machines considers that the tickets have been dispensed SEMNOX SOLUTIONS PVT LTD. Page 14 PARAFAIT HARDWARE MANUAL SEMNOX SOLUTIONS PVT LTD. 2011 Page 15 PARAFAIT HARDWARE MANUAL 2011 Installation Process 1. Decide wireless access point positions • Access point should be installed in free space, preferably on ceiling. It is to be installed away from pillars, beams or any other heavy metal structures to deliver maximum signal strength. • 2. Machine level hardware interface • Decide the location on the machine to fix tap reader • Refer flow chart for interface board connections • Connect the reader to the interface board using 10 pin Flat Ribbon Cable (FRC). There are 2 connectors in a reader. P - Connect reader to interface board C - Connect reader to configuration PCB while configuring the machine • On connecting the interface board to power, the LED on the interface board should glow • On connecting the FRC between the reader and the interface board, the interface board LED should glow and display should come up 3. Install Parafait Server in server computer • Refer Parafait Software installation instruction manual to install Parafait Server. Acrobat Document 4. Connect Server to Wi Fi Access Point • Connect WiFi access point to server computer and configure. 5. Enter Game machine details in Parafait Management Studio SEMNOX SOLUTIONS PVT LTD. Page 16 PARAFAIT HARDWARE MANUAL 2011 • Login to Parafait Management Studio. • Open Games, open Game Profile. Categorize the games depending on their types. • Open Games Enter details of games • Open Machines Enter details of the machines like access point name, machine address etc. Mention MAC address of the reader which is installed in the game machine. 6. Turn on Parafait Primary Server • Double click on Parafait Primary server shortcut in server computer to start the server 7. Configure machines to communicate with the access points Refer page 4 for more on reader wifi chip configuration. 8. Issue 2 technician cards for testing • Issue 2 tech cards from Parafait Management Studio • One is Physical ticket card another E-ticket card 9. Testing • Swipe physical ticket card and play games. In case of redemption games, check whether physical ticket dispensed and e-ticket count in the reader are in sync. • Play games using E-ticket card. Check whether e-ticket update is proper. Machine should not through Ticket Error in case of proper e-ticket update. Physical ticket will not be dispensed in this case. SEMNOX SOLUTIONS PVT LTD. Page 17 PARAFAIT HARDWARE MANUAL 2011 Product Details Product Name : Parafait Reader Wireless Model Number :PARARDR001 FCC Id : G7H-SPRW001 IC Id : 10387A-SPRW001 Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution!!! • Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. • This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Part 15B compliance statements for digital devices: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, SEMNOX SOLUTIONS PVT LTD. Page 18 PARAFAIT HARDWARE MANUAL 2011 the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions 1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage adioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with radio frequency exposure limits set forth by Industry Canada for an uncontrolled Environment. This equipment should be installed and operated with minimum distance 20 cm between the device and the user or bystanders. Cet équipement est conforme aux limites d'exposition aux radiofréquences définies par Industrie Canada pourun environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre le dispositif et l'utilisateur ou des tiers. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection SEMNOX SOLUTIONS PVT LTD. Page 19 PARAFAIT HARDWARE MANUAL 2011 against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception n, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Cet équipement a été testé et jugé conforme aux limites de Classe B pour un appareil numérique, en vertu de l’article 15 de la réglementation de la FCC. Ces limites ont été instaurées pour fournir une protection raisonnable contre toute interférence nuisible dans une installation résidentielle. Cet équipement génère, utilise et peut émettre de l’énergie radiofréquence. S’il n’est pas installé et utilisé conformément aux instructions, il peut provoquer des interférences sur les communications radio. Cependant, il n’est pas garanti que des interférences ne se produiront pas dans certaines installations. Si cet équipement cause des interférences à la réception radio ou télévisée (ce qui peut être vérifi é en éteignant l’appareil puis en le remettant sous tension), l’utilisateur peut tenter de les résoudre en suivant une ou plusieurs des mesures ci-après : Réorienter ou déplacer l’antenne réceptrice. Augmenter l’espace entre l’appareil et le récepteur. Brancher l’appareil à une prise de courant différente de celle sur laquelle le récepteur est branché. Pour obtenir de l’aide, contacter le vendeur ou un technician radio/télévision expérimenté. REMARQUE : Toute modifi cation non autorisée expressément par le fabricant responsable de la conformité peut annuler le droit de l’utilisateur à faire fonctionner le produit. SEMNOX SOLUTIONS PVT LTD. Page 20 PARAFAIT HARDWARE MANUAL SEMNOX SOLUTIONS PVT LTD. 2011 Page 21
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 21 Producer : Bullzip PDF Printer / www.bullzip.com / Freeware Edition (not registered) Create Date : 2012:06:13 09:49:52 Modify Date : 2012:06:13 09:49:52 Author : pc1 Title : Creator : PScript5.dll Version 5.2.2EXIF Metadata provided by EXIF.tools