Senao Co 2511BGPLUS Wireless Outdoor Bridge User Manual

Senao International Co Ltd Wireless Outdoor Bridge RBmenu ch0

a href="https://usermanual.wiki/Senao-Co" itemprop="url"> Senao Co >

Contents

Manual

SENAOWireless Outdoor BridgeSL-2511BG PLUSUser’s ManualBefore operating the unit, please read this manual thoroughly, and retain itfor future reference.ContentsChapter 1 – Hardware InstallationBefore You Start .................................................................................... 1-1Locate the Router/Bridge and Inline Power Injector Ports ………............ 1-2Preparing Installation ………....................................................….......... 1-3Outdoor Installation ...........................…………………………………… 1-5Chapter 2 – Quick SetupConfigure Requirements ........................................................................ 2-1Configure the RB ......…………………………….................…...….......... 2-4Configure the RB as bridge mode Root AP .......................…...….......... 2-5Configure the RB as Root AP with PPPoE Ethernet connection ........ 2-11Configure the RB as Root AP with dynamic IP address Ethernet …..... 2-13Configure the RB as Root AP with static IP address Ethernet ….......... 2-15Configure the RB as Remote Extension Bridge ....................…...…..... 2-17Chapter 3 – Further ConfigurationConfigure Requirements ........................................................................ 3-2Configure the RB ......…………………………….................…...….......... 3-5Security ……………………………………........................…...…......…. 3-20Configure DHCP server …………………........................…...…......…. 3-24Configure Virtual Server ………………….......................…...…......…. 3-25Configure Routing Table …………………………….........…...…......…. 3-27Configure Bridge …………………………........................…...…......…. 3-28Configure SNMP………………………………………..........…...…......…. 3-29Configuration Review and Apply the New Settings …………….…..…. 3-30Utility …………………………………….........……............…...…......…. 3-31Chapter 4 – Command Line InterfaceAppendix A – Specifications Appendix B – Default Settings Appendix C – Regulatory Compliance Information
1 - 1Chapter 1 Hardware InstallationThis chapter describes the procedures for installing the OutdoorRouter/Bridge.Note: Before you mount the Router/Bridge to a mast or on the side of abuilding, be sure to configure and test the device first.Here’s what you’ll find in this chapter:_ Before You Start_ Locate the Router/Bridge Ports_ Preparing for Installation_ Outdoor InstallationBefore You StartAfter unpacking the system, make sure the following items are present andin good condition, as shown in Figure 1.1:1. MIL-C-5015 style Ethernet Cable 2. Router/Bridge3. Reverse Polarity-N Female RF Cable 4. Cross over Ethernet Cable5. Mast Mounting Kit 6. Wall Mounting Kit7. MIL-C-5015 style RS232 Console Port Cable8. Inline Power Injector 9. AC Power Cord10. User’s Manual1 - 2Locate the Router/Bridge and Inline PowerInjector Ports as shown in Figure 1.2z Special Ethernet port 1 for connecting the MIL-C-5015 style EthernetCablez Special serial port 2 for connecting the MIL-C-5015 style RS-232console port cablez Reverse Polarity-N Male connector 3 for connecting the antenna or RFcable.z Power & Data output port 4 for connecting the other of the MIL-C-5015style Ethernet Cablez Data input port 5 for connecting the Ethernet Cable to a Hub SwitchRouter or a PC.z AC power input port 6 for connecting the power cord.
1 - 3Preparing InstallationBefore installing your Outdoor Wireless LAN system for your outdoorapplication in a hard-to-reach location, we recommend that you configureand test all the devices first.For configuring the Outdoor Router/Bridge, you need follow the quick stepsbelow to power up your Router/Bridge:Step 1: With the unit powered off, attach one end of the RF cable to theantenna connector and then connect the antenna to the other end of the RFcable as shown in Figure 1.3.Step 2 Plug the female end of the power cord into the Inline Power Injector,and then plug the male end of the power cord into a power outlet or powerstrip. The Power LED on the front of the Inline Power Injector will light up.Step 3 Run the cross over Ethernet cable (included in your package) fromData Input Port (on the front of the Inline Power Injector) to the Ethernet Porton a PC.NOTE: This connection is required for setting up initial configuration1 - 4information. After configuration is completed, this cable will be removed, andthen you should run an Ethernet cable from Data Input Port (on the front ofthe Inline Power Injector) to the LAN connection (such as to a hub, bridge ordirectly into a patch panel).Step 4 Plug the MIL-C-5015 style Ethernet connector into the SpecialEthernet port on the back of the Router/Bridge.Step 5 Plug the RJ-45 Ethernet connector (the other end of the SpecialEthernet cable) into the Power & Data Output Port on the front of the InlinePower Injector.When the Router/Bridge receives power over the Ethernet cable, theRouter/Bridge will start its boot sequence and the Active LED on the front ofthe Inline Power Injector will light up.You can configure the Router/Bridge using the HTML browser, such asInternet Explorer or Netscape Navigator from a remote host or PC.(Please consult the “Quick Setup” section).
Download:
Mirror Download [FCC.gov]
Document ID267726
Application IDmp6N5vmWOmhfyzCLJ2PJnA==
Document DescriptionManual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize204.06kB (2550800 bits)
Date Submitted2002-09-04 00:00:00
Date Available2002-09-04 00:00:00
Creation Date2002-09-02 03:18:41
Producing SoftwareAcrobat Distiller 5.0.5 (Windows)
Document Lastmod2002-09-04 14:47:40
Document TitleMicrosoft Word - RBmenu-ch0.doc
Document CreatorADOBEPS4.DRV Version 4.50
Document Author: demi
FCC ID Filing: NI3-2511BGPLUS

Navigation menu