Senao Co SI-7800B Wireless LAN AP User Manual

Senao International Co Ltd Wireless LAN AP

users manual

SENAO International 第 1 頁，共 17 頁 SI 7800B AP Simple Manual
SENAO International 第 2 頁，共 17 頁 1. Understanding the Hardware 1.1 Hardware Configuration RJ-45 Ethernet Connector – Provides 10 Mbps connectivity to a wired Ethernet LAN. Reset Button – By holding this down for more than 3 seconds, the unit will reset to its factory default settings. Power Supply Connector – Connects to the power adapter. 1.2 Hardware Installation A. Configure your notebook or PC with a wireless LAN card. B. For a wired LAN, connect your PC’s Ethernet port to the unit’s LAN port via an Ethernet cable. C. For WLAN, position the unit in a proper location. D. Plug in the power cord into the power outlet.
SENAO International 第 3 頁，共 17 頁 2. System Consists of Administrator Settings、Firmware Upgrade、Reset、Restore Defaults 1. Administrator Settings Enter new password and then click save and restart
SENAO International 第 4 頁，共 17 頁 2. Firmware Upgrade step 1 step 2 Click Browse to find new Firmware，then click save and restart 3. Reset Click Reset
SENAO International 第 5 頁，共 17 頁 4. Restore Defaults Click Restore Defaults 3. LAN Consists of LAN Settings、DNS Settings 1. LAN Settings Change IP Address、Subnet Mask Default and Gateway and then click save and restart
SENAO International 第 6 頁，共 17 頁 2. DNS Settings Enable DNS Relay Service，change Domain Name Suffix and Primary Domain Name Server Address and then click save and restart 4. Services 1. Network Servives Consists of SNMP Server、DHCP Server、System Log Daemon、Easy Setup Wizard A. SNMP Server step 1 Enable and then click Configure to enter into settings step 2
SENAO International 第 7 頁，共 17 頁 Read only community , enter public Read write community, enter private After modifications, click save and restart
SENAO International 第 8 頁，共 17 頁 B. DHCP Server step 1 Enable and click Configure to enter into settings step 2 Change IP Pool starting Address、IP Pool Ending Address and Lease Time and then click save and restart
SENAO International 第 9 頁，共 17 頁 C. System Log Daemon step 1 Enable and click Configure to enter into settings step 2 Change System Log Daemon IP Address and System Log Daemon Port number and then click save and restart
SENAO International 第 10 頁，共 17 頁 D. Easy Setup Wizard Click Enable to use Easy Setup Wizard
SENAO International 第 11 頁，共 17 頁 5. Wireless Consists of Settings、Operational Mode、Security Settings、MAC Filtering 1. Settings Click save and restart after change 2. Operational Mode Click save and restart after change
SENAO International 第 12 頁，共 17 頁 3. Security Settings Click save and restart after change 4. MAC Filtering Click save and restart after change
SENAO International 第 13 頁，共 17 頁 6. Information Consists of System Status、Wireless Status、Association List、LAN Statistics、Wireless Statistics、DHCP Client List 1. System Status You can find LAN and System Information settings here 2. Wireless Status You can find SSID and Channel settings here
SENAO International 第 14 頁，共 17 頁 3. Association List You can find what wireless LAN or AP are attached to SI 7800B AP 4. LAN Statistics You can find the Total Bytes、Total Packets、Total CRC here
SENAO International 第 15 頁，共 17 頁 5. Wireless Statistics You can find Unicast Packets、Broadcast Packets、Multicast Packets here 6. DHCP Client List You can find which client are connected to server when AP Enable DHCP Sever was used
SENAO International 第 16 頁，共 17 頁 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
SENAO International 第 17 頁，共 17 頁 IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu