Senao Networks FS2 Single Line Long Range Cordless Telephone User Manual FreeStyl 2 English Dec052012

Senao Networks, Inc. Single Line Long Range Cordless Telephone FreeStyl 2 English Dec052012

User Manual

Download: Senao Networks FS2 Single Line Long Range Cordless Telephone User Manual FreeStyl 2 English Dec052012
Mirror Download [FCC.gov]Senao Networks FS2 Single Line Long Range Cordless Telephone User Manual FreeStyl 2 English Dec052012
Document ID1857709
Application IDARenPIClWVxCC6zDGXS/cQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize74.23kB (927889 bits)
Date Submitted2012-12-12 00:00:00
Date Available2012-12-12 00:00:00
Creation Date2012-12-05 17:26:35
Producing SoftwareGPL Ghostscript 9.05
Document Lastmod2012-12-12 09:40:19
Document TitleFreeStyl 2_User Manual_English_Dec052012
Document CreatorPDFCreator Version 1.5.0
Document Author: 100237

Table of Contents
User Manual (English)
FreeStyl 2
Digital Long Range Cordless Phone
Safety Instructions ............................................................................. 4
General Safety Instructions............................................................ 4
Product Safety Instructions............................................................ 4
Battery Safety Instructions ............................................................ 6
Regulatory Information...................................................................... 7
Equipment Checklist ........................................................................ 10
Handset Illustration.......................................................................... 11
Handset Features ............................................................................. 13
Basic Handset Features................................................................ 13
Additional Handset Features ....................................................... 15
Base Illustration ............................................................................... 21
Base Features ................................................................................... 21
Base Features ................................................................................... 22
Basic Base Station Features ......................................................... 22
Charger Illustration .......................................................................... 23
Charger Features.............................................................................. 24
Getting Started................................................................................. 25
Base Station Installation .............................................................. 25
Handset and Charger Installation ................................................ 26
Basic Operations .............................................................................. 27
Operation Modes ......................................................................... 27
A. Base Operation Modes ........................................................ 27
B. Handset Operation Modes................................................... 27
Making a Telephone Call.............................................................. 29
Making an 2-Way/ Intercom Call ................................................. 29
Making a Broadcast...................................................................... 30
A. Handset to Handset Calls..................................................... 30
Redial............................................................................................ 31
Receiving a Telephone Call .......................................................... 31
Receiving an Intercom Call........................................................... 32
Ending a Call................................................................................. 33
Adjusting Handset Receiver (Earpiece) Voice Volume ................ 33
~2~
Adjusting Handset Speakerphone Voice Volume ........................ 33
Placing a Call On Hold .................................................................. 33
Mute............................................................................................. 34
Do Not Disturb (Silent Ring)......................................................... 34
Key Guard..................................................................................... 34
Battery Recharge and Replacement ............................................ 35
Advanced Operations....................................................................... 36
Handset Registration ................................................................... 36
Handset Group Subscription........................................................ 37
Call Transfer ................................................................................. 38
Phonebook Operations ................................................................ 39
Call Barring ................................................................................... 43
Programmable Feature Call ......................................................... 45
Caller ID ........................................................................................ 47
Visual Message Waiting Indicator (VMWI) .................................. 48
Adjust Handset Microphone Gain (sensitivity) ............................ 49
Adjust Headset Ring ..................................................................... 49
Baby Monitor ............................................................................... 49
Index................................................................................................. 57
Technical Specifications ................................................................... 61
FCC Part 68 Statement..................................................................... 62
IC CS-03 Statement .......................................................................... 63
Safety Instructions
Caution: Your wireless telephone gives you freedom and flexibility to
stay in touch while you move around. However, when using your phone
equipment, safety instructions should be followed to avoid the risks of
fire, electric shock, injury to person, and damage to property.
General Safety Instructions
1.
2.
When using your wireless phone, ensure your safety and the safety of others:
a.
Always watch where you are walking and standing.
b.
Don’t let a phone call distract you from working safely.
c.
If power goes out, it won’t work, so back-up power is recommended.
In an emergency:
a.
If an emergency occurs, dial the emergency phone number. Remember: if
you are in an area where your phone does not have a clear signal from the
base, it is highly probable that the call may not go through. Locate the
nearest landline telephone or other communications device to call for help.
b.
Emergency calls may not automatically provide emergency personnel with
your name, phone number or location.
3.
Notice to Hearing Aid Users: This phone system is compatible with inductively
coupled hearing aids.
4.
Notice to Cardiac Pacemaker Users: Preliminary studies done by the US FDA
and others have shown that, although interference to the implanted cardiac
pacemaker may occur when operating very closely, wireless telephones “do not
seem to pose a significant problem for pacemaker wearers.” However, until
more is known, FDA suggests that people with pacemakers may want to take
precautions when using or carrying a wireless telephone to ensure that there is
ample distance between the telephone and the pacemaker. Do not carry the
handset in a breast pocket. If you have any reason to suspect that interference
is taking place, turn off your handset immediately.
Product Safety Instructions
~3~
1.
Read and understand all instructions.
2.
Follow all warnings and instructions including those marked on the product.
~4~
3.
Changes or modifications to this product not expressively approved by the
manufacturer will void the warranty and the FCC authorization to operate the
equipment. Use only manufacturer provided accessories.
17. Do not install the base station or the handset charger near microwave ovens,
radios, TV sets, speakers, or other electrical equipment. These appliances may
cause interference to the product or experience interference from the product.
4.
Do not use the telephone near water. Never spill liquid of any kind on this
product.
18. Unplug the base station or the charger adaptor from the power outlet and refer
to an authorized service center under the following conditions:
5.
Unplug the product from the wall telephone jack and power outlet before
cleaning. Do not use liquid or aerosol cleaners. Use damp cloth for cleaning.
6.
Do not place this product on an unstable cart, stand, or table. The product may
fall and cause personal injury or damage to the product or other property.
7.
Power Outage: In the event of a power outage, your handset charger will not
recharge the handset battery, and the base station will not allow you to make
an outgoing call or take an incoming call. Both the charger and the base station
require electricity for operation. You should have a telephone that does not
require electricity available for use during power outage, or have a temporary
backup power supply.
8.
9.
Slots or openings in the product’s housing are provided for ventilation. These
openings must not be blocked or covered. Placing the product on a bed,
carpeting, or other similar surface may block these openings and should be
avoided. This product should never be placed near or over a radiator or heat
register, or in a built-in installation unless proper ventilation is provided.
Never push objects of any kind into this product through housing
slots/openings as they may damage the product, touch dangerous voltage
points or short out parts that could result in fire, electric shock, or injury.
a.
b.
c.
d.
e.
f.
If liquid has been spilled into the product.
When the power supply cord or plug is damaged or frayed.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating
instructions.
If the product has been dropped or housing has been damaged.
If the product shows a distinct change in performance.
Battery Safety Instructions
1.
Use only manufacturer approved Li-ion rechargeable batteries and charger. Do
not use other types of rechargeable batteries or non-rechargeable batteries.
The batteries could short-circuit, and the battery enclosure may be damaged
causing a hazardous condition.
2.
Follow the charging instruction in this manual and instruction labels and
markings in the handset and charger compartments.
3.
The battery should not be charged in the place where the temperature is less
than 0℃ or greater than 40℃
10. This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your
home, consult your dealer or local power company.
4.
Battery must be recycled or disposed of properly. Do not dispose the battery in
a fire. The cells may explode.
5.
11. Do not overload wall power outlets and extension cords as this may result in
fire or electric shock.
Do not dispose of the battery in municipal waste. Check with local codes for
disposal instructions.
6.
12. To avoid electric shock or burn, do not disassemble this product. Send this
product to an authorized service center when service or repair work is required.
Opening or removing covers may expose you to dangerous voltages, electrical
currents or other risks. Incorrect reassembling of the product may cause
electric shock when the product is subsequently used.
Exercise care in handling the batteries in order not to short-circuit the battery
with conductive materials such as rings, bracelets, keys, pocketknife, and coins.
The battery or conductive material may overheat and cause burn or fire.
7.
Do not expose batteries to rain or water.
8.
Do not open or mutilate the battery. Released electrolyte is corrosive and may
cause injury to eyes or skin. The electrolyte may be toxic if swallowed.
13. Avoid using the product during a storm. There may be a risk of electric shock
from lightning.
9.
During charging, the battery heats up. This is normal and is not dangerous.
14. Do not place the product where persons can step, trip, or fall on it.
15. Do not place conductive objects over or near the antenna.
16. Do not use the product to report a gas leak while in the vicinity of the leak.
~5~
~6~
Regulatory Information
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
FreeStyl 2
FCC ID：U2M-FS2
IC：3616C-FS2
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including
interference that may cause undesired operation.
Base Station
Federal Communication Commission Interference Statement
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Federal Communication Commission Interference Statement
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
~7~
This device has been designed to operate with an antenna having a maximum
gain of 1.5 dBi. Antenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The required antenna impedance is 50 ohms.
Portable Handset
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
~8~
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
Equipment Checklist
1.
In a Base + Handset package, please find the following components:
a. Base Station x 1 (antenna installed)
b. Base AC/DC Adaptor x 1
c. Handset x 1 (antenna installed)
d. Desktop Charger x 1
e. Charger AC/DC Adaptor x 1
f. 1100mA Li-ion Battery Pack x 1
g. Telephone Cord x 1
h. CD (User’s Manual), Quick Guide
i. Belt clip x 1
2.
In a Handset package, please find the following components:
a. Handset x 1 (antenna installed)
b. 1100mA Li-ion Battery Pack x 1
c. Desktop Charger x 1
d. Charger AC/DC Adaptor x 1
e. Quick Guide
f. Belt clip x 1
3.
Optional Accessories
a. Outdoor External Antenna Kit for Base Station (including antenna and
cable)
b. Indoor External Antenna Kit for Base Station (including antenna and
cable)
c. Lightning Protection Kit
d. High-gain handset antenna (Long antenna)
e. Headset
f. Antenna Splitter
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with FCC RF exposure compliance requirements, please follow operation
instruction as documented in this manual.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with IC RF exposure compliance requirements, please follow operation
instruction as documented in this manual.
This device has been designed to operate with an antenna having a maximum
gain of 1.5 dBi. Antenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The required antenna impedance is 50 ohms.
~9~
~10~
Handset Illustration
Antenna
Receiver
(Earpiece)
Speaker
Phonebook
Display
Soft key
(2.5mm)
Headset Jack
Soft key
Broadcast
Caller ID / Hold
Talk / Flash
End / Power Off
Battery Cover
Up / Down
Dialing key
Speakerphone
Intercom
Microphone
~11~
~12~
Handset Features
Basic Handset Features
1.
4-line LCD (Liquid Crystal Display)
a. The LCD display has LED (Light Emitting Diode) for backlighting.
st
b. The 1 line of LCD consists of icons.
c. Icons explanation from left to right
(1) RSSI level (Receive Signal Strength Indicator)
During a call, the number of bars is
proportional to the radio signal strength
received.
(2) Link mode
(2.1) Call in-progress (ON/OFF-Hook)
The phone symbol indicates the phone line is
active when making incoming or outgoing call.
(2.2) Intercom in-progress
Indicates if Intercom mode is active
Indicate the Handset ID which is making intercom with.
(3) Speech mode
(3.1) Speaker Indicator
Indicate if the speaker is active
(3.2) Headset mode
(4) Sound and Indication
(4.1) Enable ringer
2.
Ringer
a. Rings to an incoming call and intercom call.
b. Distinctive alert sounds indicating various events:
(1) Single beep: successful key entry.
(2) Double beep: indicates power on/off.
(3) Triple beep: failed operation.
(4) Periodic 1-Long-2-Short beep (every 1 minute): low battery
warning、out of range or call on hold
Re: No any beep for invalid key entry.
3.
TALK/FLASH (
a. Places or answers a telephone or intercom call
b. Sends a Flash signal to phone line to retrieve a dial tone after the call ends,
or to perform the call waiting feature provided by local phone companies
during a call. See page 18 for more information.
Re: Default flash time is 600ms.
4.
SPEAKERPHONE (
Press the key to enable/disable the speakerphone during incoming, outgoing or
intercom call.
5.
2-WAY INTERCOM (
a. Places an intercom call to another handset, a group handset (group paging)
or all registered handsets.
b. Intercom calls are digital, full duplex, and are conducted without the
assistance from the base station.
6.
BROADCAST (
a. Half duplex broadcasting to handsets for immediate announcement
b. Half duplex broadcasting to base stations
(4.2) Disable ringer
(4.3) Ringer and vibrate mode
(4.4) Vibrate mode
(5)
(4.5) Message waiting indicator
Disable PA
Indicate if the incoming broadcast is disabled.
Two-Digit Handset ID
Displays the 2-digit Handset ID of own.
Battery Strength
Number of bars is proportional to the amount of battery time
remaining.
d. The 2nd and 3rd lines of the LCD, maximum 16 characters each, display
status, message, menu selections, or user-editable alphanumerical
characters.
e The last line displays the left and right soft keys.
Re：Press the
key on the left top corner of handset to activate the
broadcast function.
(6)
11
(7)
~13~
7.
Left/Right Soft Keys (
a. Make menu selection.
8.
) /Down(
) Scrolling Keys
Up(
a. Scroll through records and menu selections.
~14~
b. Adjust receiver voice volume when in the Talk mode.
c. Press
to adjust ringer volume when in the Standby mode.
d. Press
to enter phonebook when in the Standby mode.
9.
6.
DND (Do Not Disturb, i.e., Silent Ring)
7.
Call Logs
a. Redial: Stores 10 phone numbers (up to 26 digits each) dialed most
recently. Can perform last-number redial on all 10 numbers.
b. Received & New Call Log: Total 50 entries (16-digit phone number, 16character names, and Date/Time stamp), needs Caller ID service from local
telephone company.
c. Phone numbers and names can be saved into phonebook while in display.
8.
Call Barring: Block outgoing calls and incoming calls.
a. Outgoing call:
a-1. Block the users from dialing long distance calls or international calls
a-2. Up to 5 digits of each call barring setting; up to 5 entries allowed.
END; On/Off Key (
a. Ends a call.
b. Leaves current menu operation, up one level.
c. Press for 3 seconds to turn off the handset.
10. CALLER ID Key (
a. Review caller ID list.
b. Including received and missed caller ID.
Additional Handset Features
1.
Multiple handsets registration
a. Up to 9 handsets can be registered to a base station
b. ID 11-19: individual Handset IDs.
c. ID 91-99: Group IDs. Handsets can “subscribe” from the handset menu to
group(s) and be paged when an intercom caller enters a Group ID.
b.
Incoming call:
b-1. PA On/Off: Enable or disable the broadcast from other handsets or
base station. When PA is Off, the handset can’t receive broadcast from
base station or other registered handsets, but it can broadcast to base
station or other registered handsets.
b-2. Line On/Off: Enable or disable the capability to receive incoming call
from telephone line. When Line is Off, the handset can’t receive incoming
call from telephone line, but it can still make outgoing call.
b-3. Int. On/Off: Enable or disable the intercom from other handsets or
base station. When Int. is Off, the handset can’t receive intercom from base
station or other registered handsets, but it can intercom to base station or
other registered handsets.
c. This changing requires to entering the “Call Settings” (MENU-4-3).
[Note] You need to key in the accurate user ID and password to perform this
feature. The default password is 0000.
2.
Ringer Vibrator
a. Two options for Line (incoming call) ringing & Intercom ringing.
b. Six-level ringer volume selections (Off/Low/Medium/High/Vibrate/ Vibrate
& High) for each option.
c. Eight ringer type selections for each option.
3.
Caller ID
Displays incoming call phone number and name on the LCD (needs Caller ID
service from local telephone company or PBX/Key phone system analog port).
4.
Call waiting with caller ID
nd
st
Displays 2 incoming call information on the same phone line when 1 call is in
progress (needs Call Waiting with Caller ID service from local telephone
company or PBX/Key phone system analog port).
9.
Name tagging with caller ID
Match the caller ID with the phone book entries; once matched, the LCD screen
will display the name or nickname instead of pure caller ID info (needs Call
Waiting with Caller ID service from local telephone company or PBX/Key phone
system analog port).
10. Key-guard
a. When the keyguard is selected, all keys will be locked.
Press UNLOCK (Left) soft key followed by ＊ to release it.
b. The keyguard will be automatically enabled once returning back to idle
mode for 15 seconds.
5.
~15~
Any Key Answer (except
and SILENT Soft Key)
~16~
11. Dialing Prefix
a. Up to 14 digits, including pause(s), one access code can be preprogrammed to be added automatically in front of the dialed number
when dialing from call logs, phonebook, and dial-and-send dialing. See
page 51 for more details.
12. Call Hold
a. Places call on hold.
13. Mute
a. Press MUTE (Left) soft key during talk, the handset microphone will be
muted.
Press UNMUTE (Left) soft key to release it.
14. Phonebook
a. 50 entries, each stores a phone number or handset ID (up to 26 digits) and
name (up to16 characters)
b. Alphabetically sorted display and search by letter.
c. Dial from display.
d. During the stand-by mode, you can enter the phone book by pressing
e.
scrolling key.
Phone book transfer via air
i. Transfer specific phonebook to one handset or all registered handsets.
ii. Transfer all phonebooks to one handset or all registered handsets.
15. Key tone
a. Four-level key tone volume selections (Off/Low/Medium/High).
b. Four key tone type selections.
16. Call Timers
a. Display call time duration for current call during and immediately after the
call.
17. Programmable Feature Call
a. Allows user to pre-program the most frequently used Feature code into
FREESTYL 2.
b. Up to 10 entries can be saved.
c. Once the feature code is programmed, you can quickly perform those
functions during the active call by pressing OPTION soft key.
18. Menu Display
a. To avoid making errors, in the “Call Settings”(MENU-4), “Phone Settings”
(MENU-5) and “Base Settings” (MENU-6), these settings can be hidden.
~17~
b.
c.
Handset password is required before enter Menu Display (MENU-8), the
default handset password is 0000.
When disabling the settings, these setting will no longer be displayed,
unless enabled by entering the Menu Display again.
19. PA On/Off
a. Enable or disable the broadcast function.
b. When PA is Off, the handset can’t receive broadcast from base station or
other registered handsets; But it can broadcast to base station or other
registered handsets.
20. Group Setting
a. Allow handset to subscribe to one or several groups.
Re: Up to 9 groups (91~99) can be subscribed.
21. Custom Name
a. Allow changing the “FREESTYL 2” screen to the desired wording or info,
such as the user’s name.
Re: Up to 32 characters can be entered.
22. Change Pwd
a. Allow changing the handset password which requires entering in Call
Barring (MENU-4-3) and Menu Display (MENU-8) .
Re:Default is 0000.
23. Adjusting DTMF Duration
a. From MENU-6-1 to select variable duration of DTMF tone.
b. Default is 100ms.
c. When entering the Base Settings, PIN is required. Default is 0000.
Re: First verify the line or PBX port is not the issue by testing with another
known good analog telephone. Change this setting only when you have
verified that indeed DTMF digits are not being recognized by the PBX/Key
system. Also, check into adjusting parameters in the PBX as this may
prove more successful in getting DTMF digits to be recognized.
24. Changing the flash time
a. From MENU-6-2 to select flash key timing
b. 9-level (100 ms - 900 ms) timing selections, default= 600 ms.
c. The default value (600 ms) works in most areas. Change only when you are
certain of the new value would work.
~18~
d. When entering the Base Settings, PIN is required. Default is 0000.
Re: Do not change this setting unless you have issues with either answering
inbound calls, or transferring calls. Many newer IP-PBX’s/VOIP Server
type phone systems want a shorter flash time of 200ms or 300ms.
a.
b.
c.
d.
25. Assign next handset ID for new handset
a. Using registered handset from MENU-6 - -3, to assign
a next handset ID to a new handset.
b. If do not assign the next handset ID, the system will automatically assign a
handset ID to a new handset.
c. When entering the Base Settings, PIN is required. Default is 0000.
Re: Handset ID range is 11-19, if all ID’s are taken you will need to reset the
base to start the ID numbering over again. See page 22 for resetting the
base.
26. Clear Handset
a. Using a registered handset, press MENU-6- -4
to remove the other registered handset. (Use this if you are unable to
deregister a handset from the system (a damaged handset for example)
b. Once removing the other registered handset, you will be able to register a
new handset with that ID.
c. When entering the Base Settings, PIN is required. Default is 0000.
Enter MENU-6 to set Base Settings.
Enter “7” to enter Set Time.
Enter 4 digits for MM/DD(Month/Day), then enter 4 digits for hr:mm
(Hour：Minute)
Press SAVE (left soft key) to finish the setting.
30. Mic Gain
Allow(s) changing the handset microphone gain based on the handset in
different environment(s) - Quiet, Normal and Noisy environment.
This requires entering the “Phone Settings” (MENU-5-1).
31. Headset Ring
Allow changing the ringer emitted either from handset speaker or receiver of
headset.
This requires entering the “Phone Settings” (MENU-5-9).
32. Baby Monitor
This setting will change the handset to act as a baby monitor via an intercom
call.
When setting Baby Monitor ON, this dedicated handset will not answer any
incoming calls except the 2-way intercom.
This requires entering the “Call Settings” (MENU-4-5).
27. Change the PIN
To change the base PIN, you will need to go to “Base Settings” (MENU-6-5).
a. Use a registered handset to change PIN from MENU-6-5.
b. When entering the Base Settings, PIN is required. Default is 0000.
28. Auto Hang Up feature
a. Use a registered handset, press MENU-6- -6 to
turn on/off the auto hang up feature. Default password is 0000.
The default of auto hang up is OFF.
b. When enabling the auto-hang up feature, the handset will automatically
hang up the call when the far-end hangs up the call.
Note: Use this feature with caution. The phone will end the call if a linereversal signal (momentary open signal) is detected. Sometimes this
signal is detected erroneously. If this happens often, you may need to
keep this feature turned off.
29. Set Time
The set time function allows user to set date/time to support the DTMF caller
ID (DTMF caller ID doesn’t attach date/time when receiving from PSTN, using
this setting, user is able to review the date/time when the caller ID received).
~19~
~20~
Base Illustration
Base Features
Basic Base Station Features
Page (handset locator only)
/ Registration
Power LED: blue color
In use LED: white
color
1.
Antenna
a. The antenna port has a reversed thread connector; to remove antenna or
cable, turn counterclockwise; to install, turn clockwise. Improper
installation may damage the connector.
b. When using an outdoor antenna, locate the antenna (not the base station
itself) as high as possible for a clear transmission path.
2.
LED
a. Power (blue color): indicates base station has power.
b. In-Use (white color): indicates an active telephone line.
3.
RESET Button
a. Restores base station to factory settings
b. Reset button is intended to prevent accidental system reset.
c. All handsets (including administrator) need to be re-registered after a base
station reset.
4.
Page Button (Locate handset)
To find a misplaced handset; press “PAGE” and all registered handsets will beep
for 30 seconds.
Press “PAGE” again or any key on handset to stop.
Re: “PAGE” is for locating handset only, not able to make intercom with
handset.
5.
Registration Button (PAGE)
Enters registration mode along with handset, assigns handset ID (11-19).
6.
Line Jack
Standard RJ-11C/CA-11A connector to plug in the telephone line
7.
Telephone Jack
Another RJ-11C to plug in the optional answering machine
8.
DC In: to plug in the power adaptor
Base unit Diagram
DC Jack
Phone Jack
Reset Button Line Jack
~21~
~22~
Charger Illustration
Charger Features
1.
DC In
Connects to Charger AC Adaptor.
2.
Handset Charging Slot
a. Charge handset battery when handset is placed in cradle.
b. Refer to the handset LCD for charging status
(1) Charging: battery status bar is running and the LCD screen will show :
“Charging”.
(2) Fully Charged: battery status bar stands still and the LCD screen will
display “Charge Complete”
(3) Charge Fail: If there are any errors during charging mode, the LCD
screen will display “Charge Fail”
3.
It is impossible to overcharge the battery using this charger.
4.
The adaptor for the charging station can be used as travel charger as well.
However, you can’t turn off the power while you charge the handset via travel
charger. A warning message” “Unplug Travel Charger then OFF” will be shown
on the LCD.
Handset charging slot
Notes:
1. Fully charge battery packs before first use.
2. Handset will “power on” automatically when placed in the
charging slot.
3. However if you fully drain the battery, it will take around one
minute for the handset to auto power on.
DC in
~23~
~24~
Getting Started
Handset and Charger Installation
Base Station Installation
1.
There are three possible base station setups:
Base station alone
Base station plus telephone answering device
Base station plus standard telephone
Plug the transformer end of the Charger AC/DC adaptor into a standard AC
electric power outlet, plug the other end into the “DC In” jack on the back of
the Charger.
2.
Install battery pack onto the handset.
3.
Install handset antenna.
4.
Place handset onto the charger slot.
5.
Fully charge the battery for three hours before use.
6.
The phone system is now ready to perform basic functions such as making and
receiving phone calls and intercom calls. No base station or handset
programming is needed for basic operations.
For best performance, maintain at least a distance of 1 meter (about 3 feet)
between the base station and other electronic devices (e.g., TV, computer, stereo,
fax machine, answer machine, cordless phone, etc.)
1.
Install base station antenna.
The base station’s antenna port has a
Reversed-thread connector; to install
antenna or cable, turn clockwise; to
remove, turn counter-clockwise. Improper
installation may damage the connector.
2.
Plug the transformer end of the base
station AC/DC adaptor into a standard AC
electrical power outlet, plug the other end
into the “DC In” jack on the back of the
base station.
a. The base adaptor’s DC plug is same
dimension as the charger’s DC plug.
The charger adaptor’s DC plug can fit
into the base’s DC In jack.
3.
Plug phone cord into the “LINE” Jack
4.
A standard telephone or answering machine can be plugged into the adjacent
jack on the back of the base station marked TEL
~25~
Note:
1. Handset(s) packaged along with a Base Station are preregistered at the factory. If you have a new handset, you will
need to register the handset with the base station in order to
be recognized as a member handset by the base(s) and by
other handsets. See Handset Registration.
2. Fully charge battery packs before the first usage.
~26~
3.
Basic Operations
Menu Tree
Operation Modes
Both the base station and handset have levels of operation at which time only
certain procedures of functions can be performed.
A. Base Operation Modes
1. STANDBY mode- this is the default mode. The page key is active in standby
mode only. The base “Power” (blue color) LED will light up during this mode.
2.
TALK mode- the base station operates in this mode during phone call. The “In
Use” (white color) LED will light up during this mode.
3.
REGISTRATION mode- the base station enters this mode by pressing the PAGE
button for three seconds. The “Power” (blue color) LED will be blinking in
“Registration” mode, also a prompt sound will be emitted.
B. Handset Operation Modes
1. STANDBY mode- this is the default mode.
a. If there is no on-going activity, the handset
automatically goes into SLEEP/STANDBY mode to save
battery power.
b. The handset can be turned off completely by holding
c.
d.
2.
Down the
key for 3 seconds.
The standby screen display (custom name) can be
edited.
The 2-dight number represents the handset ID
MENU mode
a. Press the Right soft function key to activate Menu
mode.
b. In Menu mode, the handset settings and information
contained in memory can be changed.
c. The functions available through the Menu selection
are covered in greater detail from page 53.
d.
Main Menu
1.KeyGuard
SELECT
BACK
The Menu structure display as below:
~27~
~28~
1. Press
key followed by a two-digit handset ID or
Group ID.
Making a Telephone Call
1.
Press
number.
, wait for dial tone, and then enter phone
2. Alternatively, you can enter phone number first then press
key.
When using this method, you can use the CLEAR (Left) and
DELETE (Right) soft keys to edit the number entered.
“Delete” erases the last digit entered. “Clear” erases the
entire line but remains in the dial-and send dialing.
3. Speed dial by accessing the entries in the phone book
(Menu 2)
a. Press
or
scrolling key to enter the phone book
b.
4.
Press
to dial out the number
To abort dialing, press
2. Press
key to end the call.
Notes:
1. Intercom calls can be made regardless if the Base Station is
present.
2. If a Group ID is entered, the first handset (belonging to that
group) that answers will establish a link with the caller. See
Handset Group Subscription.
3. If a link cannot be established, the LCD shows “Paging timeout”
after a 35-second time out.
Making a Broadcast
A. Handset to Handset Calls
1. Broadcasting all handsets
a. Press and hold
key (left top corner of keys) from
key.
one handset.
b. Hear a long “Du…” sound while the initiating handset
broadcasts to all handsets within communication
coverage.
c. Speak the message to be broadcasted once you hear the “Du Du” sound; the
speakerphone of destination handsets will open if it receives a voice.
Notes:
1. If a link cannot be established, the LCD will show “Base not
found” after a 6-second time out.
2. A call duration timer will start displaying the length of the call
after link is established.
Making an 2-Way/ Intercom Call
The FREESTYL 2 Cordless Phone System offers private, Intercom/ 2-way radio calls
independent of base station. Intercom/ 2-way communication can be placed
between handsets.
Re: Pressing and holding the
broadcast.
d. Release
key is needed during the speaking of the
key to end the broadcasting.
2. Broadcasting to only a group of handsets
a. Enter the Group ID and then press and hold
key
(left top corner of keys). See page 37 for instructions on
creating groups
b. Hear a long “Du…” sound while the initiating handset
broadcasting to all handsets.
c. Start to speak the message to be broadcasted once you hear the “Du Du”
sound; the speakerphone of destination handsets will open if it receives a
voice.
Re: the initiating handset press and hold the
~29~
~30~
key is needed during the
speaking of the broadcast.
d. Release
key to end the broadcasting.
If the handset is on the charger cradle (ringer will be
temporarily switched to “Ring” if it has been set to “Vibrate”),
lift the handset and press
key to start conversation.
3. Broadcasting to an individual handset
a. Enter the Handset ID and then press and hold
key
(left top corner of keys).
b. Hear a long “Du…” sound while the initiating handset
broadcast all handsets within communication coverage.
c. Start to speak the message to be broadcasted once you hear the “Du Du”
sound; the speakerphone of destination handsets will be opened if it received
a voice.
Re: the initiating handset press and hold the
speaking of the broadcast.
d. Release
key is needed during the
key to end the broadcasting.
Redial
1. Press REDIAL (Left) soft key.
Notes:
1. You can press SILENT (Left) soft key if you choose to ignore the call.
Unlike turning off the ringer (from the handset menu), the SILENT
key operation is valid only when the phone is actually ringing.
2. If Caller ID service is available, the LCD will display the incoming call
information. If the LCD shows “Private” or “Unknown”, the caller’s
information may have been blocked by the caller or the originating
phone company.
Receiving an Intercom Call
2. The LCD shows the last phone number dialed. To dial this
number, press
Re: You can turn on the “Any Key Talk” from MENU-5-2 which will allow you to
press any key instead of just the talk key, to answer an incoming call.
key.
1. When an intercom call arrives (called from other handsets,
ex. Handset 12), the ringer will ring or vibrate unless the
ringer has been turned off. Press
intercom call.
to answer the
3.
Use
or
key to scroll through the last 10 phone
numbers dialed. Select and press
key to dial the
selected number.
[Note] Intercom numbers (Handset ID) are not stored in the
last 10 numbers dialed log.
2. If the handset is on the charger cradle (ringer will be
temporarily switched to “Ring” if it has been set to
“Vibrate”), lift the handset and press
conversation.
key to start
3. If the handset is not on the cradle and MENU-6-2 “Any Key Talk” setting is “On”,
press any key (except
and the SILENT soft key) to answer.
Receiving a Telephone Call
When an incoming call arrives, the LCD will show the caller ID
message, and the ringer will ring or vibrate unless the ringer
has been turned off.
~31~
Notes:
1. The LCD displays the caller’s Handset ID.
2. You can press the SILENT (Left) soft key if you choose to ignore
the call. Unlike turning off the ringer the SILENT key operation is
valid only for the current incoming call.
~32~
Ending a Call
To end a telephone or intercom call, press
cradle.
2.
key, or place handset into charger
3.
Adjusting Handset Receiver (Earpiece) Voice Volume
back to standby, then other handsets can press
or
to
pick this held call.
Handset LCD displays a call is on hold. An alert tone (double
beep) will occur every 30 seconds to remind the handset user
that a call is still on hold.
If the operation (e.g., call transfer) after putting a call on-hold
fails, the held call may be dropped.
1. Voice volume can only be adjusted during a call.
Mute
2. There are 6 levels of volume selections. Use
key to adjust
or
1. After a link is established, you can press MUTE (Left) soft
key to mute the handset microphone.
3. The new setting remains effective for all future calls until
changed.
2. When mute is active, the other end will not hear your
voice, but still can speak to you.
Adjusting Handset Speakerphone Voice Volume
3. To leave the mute state, press UNMUTE (Left) soft key. Mute is effective only
for the current call.
1. Voice volume can only be adjusted during a call (in
speakerphone mode).
2. There are 6 levels of volume selections. Use
key to adjust
Do Not Disturb (Silent Ring)
or
1. Enter the key sequence MENU-3-1, then select “Off”. Press
SELECT (Left) soft key to confirm your choice. This will turn
off the ringer until it is turn on again from the menu.
Re: When setting the ringer “Off”, the standby screen will
show “Ringer off”.
3. The new setting remains effective for all future calls until
changed.
Placing a Call On Hold
2. For temporary silencing the ringer when an incoming call
arrives, press SILENT (Left) soft key.
1. When a call is in progress, it can be put on hold by pressing
the
key.
Key Guard
2. To return to the conversation, press UNHOLD (Left) soft key
Notes:
1. The call being placed on hold can be “un-hold” by the handset
that puts it on hold. But if after you press the
~33~
1. To prevent accidental dialing, you can press MENU (Right)
soft key, then press“1” to select the KeyGuard option. The
handset keypad is locked. No key entry will be accepted.
key to go
~34~
2. To unlock the keypad, press the UNLOCK (Left) soft key,
then, within 2 seconds, press the digit “＊” to unlock.
Advanced Operations
Handset Registration
3. Once returning back to standby mode for 15 seconds, the
Keyguard will automatically re-enable.
4. Key Guard is in effect until unlocked.
Battery Recharge and Replacement
1.
Charge the battery when one or several of the following things happen:
a. Phone beeps twice (every 60 seconds in talk mode, every 10 minutes in
standby mode).
b. Battery icon is empty.
c. Phone does not respond when a power on/off key
is pressed.
d.
e.
2.
LCD and backlighting become dim.
Talk range shortfall is experienced.
You can replace the handset battery even while on an active phone call by
putting the call on-hold first and then by pressing the
key. To retrieve the
call on hold, press the talk key again after replacing the battery and powering
the handset on.
3.
Battery talk time and standby time vary depending on the talk/standby pattern
and the operating distance. Putting the handset back in the charger cradle as
often as possible is recommended for best performance. Use only
manufacturer provided battery and charger!
1.
If your handset(s) is purchased as part of a system, it has been pre-registered
with the base station at the factory.
2.
If Handset ID shows “00,” that means it is a new handset or the ID has been
erased. You need to register the handset with the base station.
3. Registering Handsets:
a. Press MENU-7 to enter the registration section.
b. Press and hold the base’s PAGE button for 3 seconds
until the In Use LED (white color) lights up and flashes;
The base station will produce a sound to remind you
the base station is in the registration mode.
c. Press handset key “1”. This completes the registration
process. The base station will assign a handset ID
between 11 and 19 automatically. The assigned ID will
be displayed on the handset LCD, indicating successful
registration. If you get a “base has no available ID”
prompt, you will need to reset the base (see page 22).
d. Repeat above steps for all additional handsets.
4. De-registration:
a. You can de-register the handset you’re using from the
base station. De-registration will reset the Handset ID
to 00, erase the system security code, and free up the
handset ID for future registration.(registrations of other
handsets)
b. After deregistration, the handset will not be able to use
the base station to make or receive phone calls, nor can
it intercom other handsets.
c. Press MENU-7 to enter the registration section.
d. Press and hold the base’s PAGE button for 3 seconds
until the In Use LED (white color) lights up and flashes;
The base station will produce a sound to remind you
the base station is in the registration mode.
e. Press the handset number key “2”. This completes the
de-registration process. Upon successful de-
~35~
~36~
registration, the handset display will show “Please
register”.
Notes:
1. The handset can change group affiliations at any time.
2. The base station is not responsible for group assignments.
Consequently, it cannot de-subscribe a handset from a group.
3. When an intercom caller enters a group ID, all handsets
subscribed to this group will ring. The first handset to answer
will establish a link with the caller. Afterward, it is a one-to-one
call, not a one-to-many call.
Notes:
1. The base station has a 30 second registration timeout starting
from pressing the PAGE button. The handset has a 6 second
registration timeout starting from the registration or deregistration option has been selected. The base station and
handset will automatically exit registration mode after
timeout.
2. Repeat registration or de-registration process if unsuccessful.
Call Transfer
While a telephone call is in progress, you can transfer it between different
handsets.
Handset Group Subscription
1. Up to nine handset groups (91-99) can be defined and
handsets can decide which group(s) they want to be in.
2. For example, Group 1 represents the Customer Service
Group, Group 2 represents the Sales Group, and Group 3 is
the Marketing Group. Suppose that Handset 11 wants to
receive incoming rings for all Sales and Marketing related
calls. Then handset 11 will need to “subscribe” to Group 2
and Group 3.
Re: the above wording is in regards to intercom , not incoming calls.
Direct transfer (Unannounced Transfer)
1. Press
key to put the call on hold.
2. Press XFER (Right) soft key, followed by the destination
handset ID, then the held call will be transferred directly.
Call Settings
2.Group Setting
SELECT
After the call transferred to the destination handset, the
original handset will go back to standby mode automatically.
BACK
3. Group Selections:
a. Press handset MENU-4 to enter the Call Settings menu
Press number “2”, handset enters group setting menu.
b.
c. Press OPTION soft key and followed by “1” key to
subscribe the group (“9＃”, ＃:1~9). Enter 1~9.
d. Repeat for all desired groups.
e. Delete group selections by pressing OPTION soft key
and followed by “2” to Unsubscribe the group.
Indirect transfer (Announced Transfer)
If you want to talk to the destination handset before the call is
transferred, you can follow the method below:
1. During the call, press
key, followed by entering the
destination handset ID.
2.
At the destination handset, press the
or
to
answer the intercom call. After talking, press
to end
the intercom call. After an intercom call is ended, the phone
on the other end will also go back to standby mode
~37~
~38~
automatically.
See table below for a list of available characters and
their orders. For example, press 2 once for the
character “A”, twice for “B”, etc.
Notes: If the destination handset does not answer after handset
paging or transferring times out, the call is routed back to the
originating handset.
Notes:
1. When entering a phone number, the cursor automatically advances
to the next digit field. Use
or
scrolling key to move the
cursor backward or forward to insert or delete (the digit above the
cursor, or left of the cursor if cursor is on the right of the last digit).
2. When entering a name, the cursor automatically advances to the
next character field if you press a different key for the next
character. If you need to enter consecutive characters from the
Phonebook Operations
1. You can store up to 50 entries in the phonebook. Each
entry can contain a phone number or handset ID (up to 26
digits) and a name (up to16 characters).
same key, you can wait for the cursor to advance or use
2. To access the phonebook, press MENU (Right) soft key,
followed by 2 ; or press
scrolling key while the
handset is in standby mode.
Main Menu
2.PhoneBook
SELECT
3. To add a new entry:
a. Press ADD (Left) soft key.
b. Enter the name when LCD prompts “Name?” Use
DELETE (Right) soft key to delete the last digit entered.
When completed, press SAVE (Left) soft key to save.
Re: Up to 16 characters can be entered as the name.
BACK
scrolling key to move the cursor backward or forward
manually. Also use
or
to move the cursor to insert (to
the left of the cursor) or delete (the character above the cursor, or
left of the cursor if cursor is on the right of the last character).
3. By default, all letters are entered in upper case. Use the * key to
toggle between upper and lower cases.
4. A “Pause” entry represents a 1 second delay in dialing the following
digits, which is useful when calling a sequence of segmented
numbers (e.g., access code, credit card number, auto-attendant
entries, etc.) Pause is entered by pressing the ＃ key twice (LCD
displays P). Entering pause twice (PP) will result in 2 seconds pause
in the dialing.
c. You will then be prompted to enter a number for the
name just entered.
Re: Up to 26 digits can be entered as the number.
d. After entering the number, press the SAVE (Left) soft
key to save this entry into phonebook.
e. If you enter a phonebook entry without a name, all
records without a name will be placed on the top of the
phonebook list.
f. To enter the name, press the corresponding keypad
number one or more times according to the order of
the character on the key.
~39~
or
~40~
5. Character Table:
Key
＊
b. Press OPTION (Right) soft key to enter the option menu.
Characters and Orders
‘+,.*()&1
ABC2
DEF3
GHI4
JKL5
MNO6
PQRS7
TUV8
WXYZ9
Caps – when in character editing.
＊– when in number editing.
Space & ＃ – when in character editing
# & P (Pause) – when in number editing
c. Press 1 to erase the intended phone entry.
d. LCD will show “Delete entry?” Press YES (Left) soft key to
confirm your change.
8. To edit a phonebook entry:
a. Use
or
scrolling key or the alphabetical search
method to locate the record to be erased or edited.
b. Press OPTION (Right) soft key to enter option menu.
c. Press 2 to edit the intended phone entry.
9.
4.
The entries are alphabetically sorted and stored as a list in an ascending order
(A to Z) from the top of the list.
5.
The first line of LCD display shows name and the 2 line shows the phone
number. If the phone number is longer than 16 digits, press OPTION (Right)
soft key and select Option 3 “View Number” to view the complete number.
6.
To search for a record:
a. Use
scrolling key to enter Phone Book mode.
nd
b.
c.
d.
Press a key that corresponds to the first character of the name you are
looking for.
For example, if you are looking for “EnGenius”, press the number 3 key
once.
Use
for.
or
scrolling key to locate the exact record you are looking
7. To erase a phonebook entry:
a. Use
or
scrolling key or the alphabetical search
method to locate the record to be erased or edited.
~41~
Dial from display:
a.
Press
or
to dial the phone number or Handset ID displayed.
10. To transfer the phonebook to another handset:
To transfer phonebook, both parties have to enter the phonebook transfer
mode first by following below:
a. Press OPTION right soft key followed by 5 or
or
scrolling key to
b.
transfer while handset is in phonebook mode.
For the phone doing the sending, press 1 to enter sending mode.
i. Either press TX ALL(left softkey) to transfer all phonebook entries to
another handset(s)
Note: if you want to transfer all entries from an handset but the entry
is not from beginning (entry #1), it will only transfer the
remaining entries. For example, if you are have 10 entries, and
you start at entry #5, then it only transfers #5 through #10.
ii. Or press TX ONE (right softkey) to transfer just one entry to another
handset(s).
Note: you will need to at the desired entry before going to the TX
ONE option for that particular entry to be transferred.
iii. Press the 2-digit handset ID or group ID, then select all phonebook
entries or one entry to be transferred.
~42~
Re : “00” means all handsets
iv. During phonebook transferring, LCD shows “Sending” and 2-digit
countdown on the LCD will indicate the remaining phonebook
numbers which are still pending to be sent.
c. For the phone that is to receive the phonebook, press 2 to enter receiving
mode.
i. When entering the receiving mode, the LCD will show “Ready”.
ii. To start to receiving the phonebook, the LCD will show “Get
phonebook from Ext. # : xx” (the handset ID that will be doing the
sending).
iii. A beep will be emitted when receiving each phonebook entry.
iv. While receiving phone book entries, a 2-digit countdown on the LCD
will indicate the number of phonebook numbers remaining.
Re: Note: The phonebook transfer is via a wireless interface so there can be
times where some entries are not transferred due to interference. It
is recommended to have handsets in very close range during
transfers.
3. To enter a Call Barring code
a. Once the Call Barring feature is turned on, you can key
in the “Call Barring” code.
Press ADD (Left) soft key then start entering the Call
Barring code after the number is entered, then press
the SAVE (Left) soft key to save.
(1) Up to 5 digits can be entered in as a Barring code. For
example, if you want to block all call dialing to
Manhanttan, NY area, you can enter 1212 as the Call
Barring code.
(2) If the base station is connected behind a PBX system, be
sure to include the outside dial tone digit as well
(example, 9 to dial out).
b. Press OPTION right soft key to delete or edit Call
Barring codes.
c. Up to 5 sets of Call Barring codes can be programmed.
d. If you want to block all outgoing calls, enter ＊＊＊＊
＊ keys followed by, press SAVE (Left) soft key to save.
Doing so will cause all outgoing calls to be restricted.
Call Barring
1. Block the users from dialing long distance or international calls. Call barring can
also be used to block incoming calls from an outside line or other registered
handset.
Note: Entering a password is required (default password is 0000).
2. Press MENU-4-3 to enter Call Barring. Enter the password
of the handset, followed by OK (Left) soft key
Block Outgoing Call
1. Press SELECT left soft key to select “Outgoing” and confirm
your selection.
2. Use
or
scrolling key to switch between On and
Off of this setting. Press SELECT left soft key to confirm
your selection.
Re：
：The default setting of Call Barring is “Off”.
~43~
Block Incoming Calls and blocking intercom or broadcasts
from handsets.
1. Press SELECT left soft key to confirm your selection for
“Incoming”.
Use
or
scrolling key to select blocking item.
a. Press SELECT left soft key to confirm your selection to
block broadcasts.
Press CHANGE left soft key to switch between On and
Off of this setting.
Re: “On” means to be able to receive broadcast from
other hansets or base station. “Off” means to restrict
the broadcast from other handsets or base station. The
default setting is “On”.
~44~
b. Press SELECT left soft key to confirm your selection for
receiving or blocking line calls.
Press CHANGE left soft key to switch between On and
Off of this setting.
Re: “On” means to be able to receive calls from outside
line; “Off” means to restrict calls from outside line.
The default setting is “On”.
c, Press SELECT left soft key to confirm your selection for
receiving or blocking intercom calls.
Press CHANGE left soft key to switch between On and
Off of this setting.
Re: “On” means to be able to receive intercom calls
from other handsets or base station; “Off” means to
restrict intercom calls from other handset or base
station. Default setting is “On”.
Programmable Feature Call
1. If the FREESTYL 2 base station is installed behind a PBX system, you may want to
pre-program some feature calls along with the PBX’s feature codes into the
handset(s).
e. Key in the feature call code of the correspondence PBX
feature i.e. F＊70 (Nortel transfer code).
Press SAVE (Left) soft key to confirm.
Re: “F” represent the Flash signal.
Note: To enter “F” press the talk key.
f. The 1st feature call and correspondence feature call
code you entered will appear on the LCD screen.
g. Press OPTION (Right) soft key to delete or edit the
feature call you programmed into the handset.
h. Repeat the same operation to enter additional (up to
ten) feature call entries.
4. How to use a pre-programmed feature call during an active
phone call.
a. Press OPTION (Right) soft key while the handset is in
talk mode.
b. Press the corresponding number of the feature call of
which you want to use, i.e. press “0” to perform the
“PBX Transfer” in the example.
2. Up to 10 most frequently used feature call codes can be pre-programmed.
3. Naming and entering feature call codes:
a. Press MENU (Right) soft key while the handset is in
standby mode.
b. Press “4”, followed by “4” to enter the “Feature Call”
menu.
c. Press ADD (Left) soft key to add a new entry.
d. Key in the name for the feature call, press SAVE (Left)
soft key to confirm.
~45~
Notes:
1. This feature call would be useful if the FREESTYL 2 base station is
connected behind a PBX system.
2. If you have not pre-programmed any feature calls into the system,
only the “#.Phonebook” will show in the OPTION menu.
3. The FREESTYL 2’s programmable feature call may not function with
all PBX or Key phone systems due to the diversity of various
proprietary systems.
~46~
b. Delete call log:
Caller ID
1. Contact with your local phone company to subscribe to this feature. The phone
system receives and displays Caller ID information transmitted by your local
phone company. This information may include the calling phone number, name,
date, and time. This unit can store up to 50 calls of caller ID information.
2. The display will show the date and time of call on the first line, followed by the
name on the second line, and the phone number on the third line. An unread
record will display “NEW” at the end of the first line of display.
3. When viewing a call record, the number can be dialed, stored to the phonebook, or
deleted.
View Call Log
1. To view the call log, press
to enter the Call Log.
or
key to scroll through the numbers and
Press
names when available.
2.
Press OPTION right soft key, you can
choose save, delete, or clear all.
or
key to
a. Save call log:
(1) Press SELECT right soft key, you can use
or
key to scrool the name, and press DELETE to edit the
name.
Then press SAVE left soft key to save the name.
(2) Use
or
key to scroll through the numbers,
and press DELETE to edit the number.
Then press SAVE left soft key to save the number.
(3) After the above process, the call log number will be
saved into the phonebook.
~47~
(1) Press SELECT right soft key followed by YES left soft
key to confirm deleting.
c. Clear All:
(1) Press SELECT right soft key followed by YES left soft
key to confirm clearing all caller ID records.
Call a Caller ID
1. Press
key, use
or
key to scroll through the call log.
2. When at the display of a caller ID entry, Press
or
to dial this number.
3. The displayed CID number in most cases will be a 10-digit number with
the 3-digit area code followed by the 7-digit telephone number. If the
area code is unnecessary for calling back, you can follow below rule to
adjust the calling back number:
a. Press FORMAT key once, the 3-digit area code will be removed.
b. Press FORMAT key twice, “1” will be added in front of the displayed
number
c. Press FORMAT key three times, it will loop back original displayed
number.
Re. The CID default is 10 digits, when press FORMAT key, it will be
7-digit 11-digit 10-digit in circle.
4.
After the displayed number chosen, press
key to call back.
or
Visual Message Waiting Indicator (VMWI)
VMWI feature is supported via FSK message signaling when received from the
phone company telephone line or PBX system; It will activate a message icon on the
handset display and flash the VOICE MESSAGE LED on the base.
Notes:
1. A subscription to the telephone company voice mail service is required.
~48~
2. If the handset still indicates the icon even after you have listened to all
messages, turn it off by pressing and holding the “Caller ID” key on the
handset.
Adjust Handset Microphone Gain (sensitivity)
The microphone gain setting option is provided so you can adjust microphone
sensitivity custom to your workplace environment (such as a loud, noisy
environment etc.). Note: You may also want to adjust earpiece settings as well if
the workplace environment is extremely loud.
a. Press MENU right soft key while the handset is in standby mode.
When enabling baby monitor mode, the “baby unit” will automatically enter the
monitoring mode via 2-way intercom.
For example, if you set handset A as a “baby unit”, when making an intercom call
from handset B, handset A will automatically enter monitoring mode without
ringing. You will be able to hear all movements around handset A via handset B.
a. Press MENU right soft key while the handset is in standby mode.
b. Press “4” (Call Settings), followed by “5” to enter the “Baby Monitor”
menu.
c. Press “CHANGE” to switch ON or OFF (default is OFF).
Re: To avoid any interruptions while monitoring is active, the handset in
baby monitor mode will not ring from incoming calls, except intercom.
b. Press “5” (Phone Settings), followed by “1” to enter the “Mic. Gain”
menu.
c. Use
or
key to scroll the “Standard”, “Medium” and “Low”
options.
d. If you are using the handset in a quiet environment, like office or
meeting room, the level of “Standard” is recommended.
If you are using the handset in a noisy environment, like a factory or
outdoor place, the level of “Medium” or “Low” is recommended.
Adjust Headset Ring
When using a headset, you can avoid missing a call due to the ringer ringing inside
the headset rather than outside the phone, by changing the ringer to the outside
speaker.
a. Press MENU right soft key while the handset is in standby mode.
b. Press “5” (Phone Settings), followed by “9” to enter the “Headset Ring”
menu.
c. Select “On”, the ringer will be heard in the headset.
Select “Off”, the ringer will be heard from the outside speaker.
Note: Default setting is “On”.
Baby Monitor
You can set any one handset as a “baby unit” to monitor a baby or older person.
~49~
~50~
Menu Operations
1.
Press MENU right soft key to enter menu mode while the phone is in standby
mode.
Re: You can either press
or
, followed by SELECT left soft key to
confirm the selected menu. Or Press the digit directly to confirm the
selected menu. For example, press MENU right soft key followed by 4 and
1 to select Ring Volume.
2.
Press 1 to select KeyGuard (see Key Guard operation on page 34 ).
3.
Press 2 to add, delete, edit, view and edit the phonebook (see Phonebook
instructions on page 39 ).
4.
Press 3 to set Sound settings:
a. Press 1 to select Ring Volume:
There are two options for ring volume: Line (for incoming call) and Intercom
(for intercom calls). Set each option respectively.
b.
When setting each option, use
or
to scroll through 6 options:
“Off”, “Low”, “Medium”, “High”, “Vibrate” and “Vibrate & High”. Press
SELECT left soft key to save selection. Default = Medium.
Press 2 to select Ring Tone:
There are two options for ring tone: Line (ring tone for incoming call) and
Intercom (ringer for intercom call). Set each option respectively.
c.
Use the
or
to scroll through 8 ringer types, press SELECT left soft
key to save the selection. Default = 1.
Press 3 to select Key Volume for when a key is pressed:
d.
Use
or
to scroll through 4 options: Off, Low, Medium, and High.
Press SELECT left soft key to save selection. Default = Medium.
Press 4 to select Key Tone for when a key is pressed:
Use the
or
to scroll through 4 options: 1, 2, 3 and 4. Press SELECT
left soft key to save selection. Default = 1.
5.
Note: Default base pin or password is 0000.
~51~
Press 4 to set Call Settings:
a. Press 1 to set Dial Prefix:
(1)
Press
or
to turn on or off the dial prefix feature. Default =
~52~
(2)
(3)
(4)
(5)
(6)
b.
c.
d.
e.
6.
Press
Press
Press
Press
Off.
If “On” is selected, the handset is prompted to enter the prefix
number (up to 14 digits can be entered).
Use Delete right soft key to delete the prefix number.
Press SAVE left soft key to confirm the selection.
When this feature is turned on, the LCD will prompt the user “Dial
Prefix? Yes or No”. On each outgoing phone call from call logs,
phonebook, and dial-and-send dialing, the current prefix is also
displayed.
Re: the prefix number will be added automatically in front of the
dialed number if the YES left soft key is pressed.
This feature is useful for access code (PBX code for outside dial tone),
a calling card, or credit card calls, etc.
2 to set Group Select: see Handset Group Subscription on page 37 .
3 to set Call Barring: see Call Barring operation on Page 43.
4 to set Feature Call: see Feature Call operation on Page 45.
5 to set Baby Monitor: see Baby Monitor operation on Page 49.
(1) Use CHANGE left soft key to select and confirm “On” or “Off". Default is
“Off”.
(2) Press SAVE left soft key to confirm selection.
f.
(1)
Use
or
3.French).
to scroll through option 1~3 (1.English 2.Spanish
Default is “English”.
(2) Press SAVE (Left) soft key to confirm selection.
g.
Press 7 to set Custom Name:
(1) Enter characters using the Character Table and method discussed in the
Phonebook section (On page 41).
Press 5 to set Phone Settings:
a. Press 1 to set Mic Gain: See Mic Gain operation on Page 49.
b. Press 2 to set Any Key TALK (answering a call by pressing any key versus
only the talk key):
Use CHANGE left soft key to select and confirm “On” or “Off".
Default is “Off”.
Re: When set to “on”, press any key (except
answer the incoming call.
Re: When Set to “On”, the handset will match the caller ID with the phone
book entries. Once matched, the LCD screen will display the name or
nickname instead of pure caller ID info (needs Call Waiting with Caller
ID service from local telephone company along with PBX system if a PBX
system is used).
Press 6 to set Language:
(2) Use
or
to move the cursor backward or forward to insert (to
the left of the cursor) or delete (the character above the cursor, or left
of the cursor if cursor is on the right of the last character).
(3) Press SAVE (Left) soft key to confirm setting.
Re: Once entering the custom name, the greeting of LCD in standby mode
will be changed to what you have entered.
and SILENT key) to
Default greeting is “FREESTYL 2”.
c.
h.
Press 3 to set LCD Contrast:
(1)
Use
or
(1) Enter original password (4 digits) of handset then press OK left soft key
to scroll through option 1~8. Default is 6.
when enter this menu (default password is 0000).
(2) Press SAVE left soft key to confirm selection.
d.
new password.
Use
or
to scroll through option 1~3 (1.8 seconds 2.On
3.Off ). Default is 8 seconds.
(2) Press SAVE left soft key to confirm selection.
e.
(2) Enter new password (4 digits) then press SAVE left soft key to confirm
Press 4 to set LCD Backlight:
(1)
Press 8 to Change Password:
Press 5 to set Name Tag:
~53~
i.
7.
Press 9 to set Headset Ring: See Headset Ring operation on Page 49.
Press 6 to set Base Settings:
When entering this menu, you must enter the Base PIN code first (4 digits).
Re: The PIN code is for Base Settings. Default is 0000.
a. Press 1 to set DTMF Duration.
~54~
(1) Enter the DTMF duration (90~200ms), press OK left soft key to confirm
b.
the setting. Default is 100ms.
Re: Please check with your dealer before changing. If the duration does not
match with the PSTN or PBX setting, some or all of the DTMF digits you
press may not be recognized.
Press 2 select flash key timing. Default is 600ms.
To avoid users changing phone settings such as Call Settings (MENU-4), Phone
Settings (MENU-5) and Base Settings (MENU-6), you can hide these menus.
Re: When entering the Menu Display, you have to enter a password first.
a.
(1) Use CHANGE left soft key to select and confirm on or off.
(1)
c.
d.
e.
f.
g.
Use
or
to scroll through option 1~9 (100~900ms). Or press
digit key (1~9) directly.
(2) Press SELECT left soft key to confirm selection.
Re: The default value (600 ms) works in most areas. Changing this setting
may cause the flash-hook signal to not be recognized properly by the
PSTN line or PBX system. You may need to change this setting if you find
you are unable to properly answer incoming calls, or are unable to
transfer calls. Many of the newer IP-PBX (VOIP server type) systems do
require a flash time of 200ms or 300ms.
Press 3 to set Assign Next HS
(1) Enter the 2-digit handset ID followed by pressing OK left soft key.
(2) Normally when registering a handset, the base will give a handset the
next available registration ID. Assign next will allow you to customize
the next registration ID (as long as it is available and between 11 and
19).
Press 4 to set Clear HS
(1) Enter the 2-digit handset ID followed by pressing OK left soft key.
(2) The base will erase the handset ID from the system.
Press 5 to Change PIN:
(1) Enter the new Base PIN followed by OK left soft key.
Re: Default Base PIN is 0000.
Press 6 to set Auto Hang Up:
(1) Use CHANGE left soft key to select and confirm on or off. The
Re: When setting “on”, the FREESTYL 2 will automatically hang up if the far
end caller has hung up. However, this function depends on if there is a
“dial tone or busy tone” signal sent out by PBX or PSTN, after the call is
hung up. Default = OFF
Press 7 to Set Time to support DTMF Caller ID:
(1) Use SAVE left soft key to select and confirm the Date and Time you
have set (see Set Time operation on page 20).
8.
Press 7 to register and de-register handsets: see Handset Registration operation
on Page 36.
9.
Press 8 to set Menu Display:
~55~
Press 1 to set hiding/un-hiding of the Call Settings menu.
b.
Press 2 to set hiding/un-hiding of the Phone Settings menu.
(1) Use CHANGE left soft key to select and confirm on or off.
c.
Press 3 to set hiding/un-hiding of the Base Settings menu.
(1) Use CHANGE left soft key to select and confirm on or off.
Re: Select “On” means the menu will be displayed on screen. Select “Off” means
the menu will be hidden.
~56~
Call Waiting with Caller ID, 15, 55
Cardiac Pacemaker, 4
Change PIN, 18, 19, 56
Charger Features, 24
Charger Illustration, 23
Index
2-Way Intercom, 14, 29
Adjusting Receiver (Earpiece) Voice Volume, 33
Adjusting Handset Speakerphone Voice Volume, 33
Adjust Handset Microphone Gain, 50
Adjust Headset Ring, 51
Base ID, 48
Base Illustration, 21
Base Operation, 27
Base PIN, 18, 19, 20
Base Station, 5, 6, 9, 10, 14, 15, 20, 22, 25, 26, 27, 28, 30, 36, 43
Base Station Features, 22
Base Station Installation, 25
Battery, 5, 7, 10, 24, 26, 27, 35
Battery Recharge and Replacement, 35
Battery Safety Instructions, 7
Battery Strength, 13
Block Incoming Call, 43
Block Outgoing Call, 43
Broadcast, 14, 16, 18, 31, 44, 49
Broadcasting a Group of Handsets, 30
Broadcasting all Handsets, 30
Broadcasting an Individual Handset, 31
BS Selection, 49
Call Barring, 16, 18, 42, 43, 54
Call Log, 16, 17, 46, 47
Call Timer, 17
Call Transfer, 33, 37
Call Hold, 17
Caller ID, 15, 20, 31, 32, 46, 47, 50, 55, 56
Call in-progress, 13
Call Manager, 49, 50, 54
Call Settings, 16, 18, 20, 37, 49, 50, 51, 54, 57
Call Waiting, 14, 15
~57~
De-registration, 36
DND, 15
Do Not Disturb (Silent Ring), 15, 34
DTMF Tone, 18
DTMF Duration, 18, 56
Electric Shock, 4, 5, 6
Emergency, 4
Equipment Checklist, 10
Flash, 14, 19, 36, 45, 48, 50, 56
Feature Call, 17, 45, 54
General Safety Instructions, 4
Group ID, 15, 30, 38, 42
Group Setting, 18, 37
Group Selections, 37, 54
Handset and Charger Installation, 26
Handset Charging Slot, 24
Handset Features, 13, 15
Handset Group Subscription, 37, 54
Handset ID, 13, 15, 17, 19, 22, 27, 30, 31, 32, 36, 38, 39, 42, 48, 56
Handset Registration, 36, 57
Handset to Handset Call, 30
Hearing Aid, 4
IDLE Mode, 17, 27, 35
~58~
Key Guard, 34, 53
Key Tone, 17, 53
Key Volume, 53
Regulatory Information, 8
REN, 8
Reset Button, 22
Ringer, 14, 15, 20, 31, 32, 34, 51, 53
Ringer Volume, 14, 15
RSSI, 13
Line Jack, 22
Lithium-Ion (Li-Ion), 7, 10
Line Reversal, 56
Safety Instructions, 4
Set Time, 20
SILENT, 15, 32, 34
Spare Battery, 10
Speed Dial, 29
Speakerphone, 14, 30, 31, 33, 48
Subscribe BS, 49
Making a Broadcast, 30
Making a Telephone Call, 29
Making an 2-Way/ Intercom Call, 29
Memory, 27
Menu Display, 18, 57
Menu Mode, 27, 53
Multiple Handsets Registration, 15
Mute, 17, 33
Talk Mode, 14, 27, 46
Talk/Flash, 14
Technical Specifications, 62
Transformer, 25, 26
Two-Digit Address Index, 13
Name Tagging, 15, 55
Outdoor Antenna, 10, 22
Phonebook, 14, 16, 17, 39, 45, 46, 47, 53, 55
Phone Settings, 18, 20, 50, 51, 54, 57
Placing a Call On Hold, 33
Power Outage, 5, 9, 25, 26
Product Safety Instructions, 5
Programmable Flash, 19
Programmable feature call, 17, 45, 46
Vibrator, 15
View Call log, 46
Visual Message Waiting Indicator, 50
Warning Message, 24
Receiving a Telephone Call, 31
Receiving an Intercom Call, 32
Redial, 16, 31
REG, 22, 37, 48
Registration Key, 22
Registration Mode, 22, 27, 36, 48
~59~
~60~
Technical Specifications
Electrical Specifications
Frequency
FCC Part 68 Statement
Channel Spacing
Number of Channels
Modulation
Multiple Access
Frequency Hopping Rate
TDD Frame Length
Number of Slots/Frame
Receiver Sensitivity
Base Station
902-928 MHz
Peak: 27 dBm
Average: 21 dBm
101 kHz
252
Differentially Encoded MSK
Frequency Hopping TDD
100 per second
10 ms
<-111dBm (@ BER 10-2)
Portable Handset
902-928 MHz
Peak: 26 dBm
Average: 20 dBm
101 kHz
252
Differentially Encoded MSK
Frequency Hopping TDD
100 per second
10 ms
<-111dBm (@ BER 10-2)
Antenna Gain
Antenna Connector
Telephone Interface
Channel Coding
Transmission Data Rate
Speech Coding
User Data Rate
Duplex
Number of System ID
Ring Signal
Flash Time
Power Source
2 dBi
Reversed TNC
RJ11 x 2
8 kbps Convolutional + CRC
85.333 kbps
8 kbps G.729AB
64kbps duplex
Time Division Duplex (TDD)
65,536
20-50 Hz, 30-90 Vrms
100-900 ms programmable
AC/DC 5V/1A Adapter
Long: 2.5 dBi; Short: 1.5 dBi
Proprietary
NA
8 kbps Convolutional + CRC
85.333 kbps
8 kbps G.729AB
64kbps duplex
Time Division Duplex (TDD)
65,536
NA
NA
3.7V/1100mAh Li-Ion Battery
550mA
(550/850mA for desktop
charger)
3hours
RF Output Power
Charger Current
Charge Time
Regulation Compliance
NA
NA
FCC Part 15, Part 68
Canada RSS-210, CS03
FCC Part 15, Part 68
Hearing Aid Compatible
Canada RSS-210, CS03
Operating Temperature
0 – 50 °C
-10 – 60 °C
Storage Temperature
-40 – 70 °C
-40 – 70 °C
Humidity
20 – 75 %
20 – 75 %
Notes:
1. NA = Not Applicable.
2. The manufacturer reserves the right to change designs and specifications without
notice.
This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the bottom of FreeStyl 2 base station is a label that
contains, among other information, a product identifier in the format US:
SNIW403BFS2. If requested, this number must be provided to the telephone
company.
Applicable connector jack Universal Service Order Codes (“USOC”) for the
Equipment is RJ11C.
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for this product is part
of the product identifier that has the format US: SNIW403BFS2. The digits
represented by 0.3 are the REN without a decimal point (e.g., 03 is a REN of 0.3).
If this FreeStyl 2 causes harm to the telephone network, the telephone company
will notify you in advance that temporary discontinuance of service may be required.
But if advance notice isn't practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations
or procedures that could affect the operation of the equipment. If this happens
the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this FreeStyl 2, for repair or warranty information,
please contact:
Company: Senao Networks, Inc.
~61~
~62~
Address: 3F, No. 529, Chung Cheng Rd., Hsintien, Taipei, Taiwan, R.O.C.
Tel no.: 886-3-328-9289
If the equipment is causing harm to the telephone network, the telephone company
may request that you disconnect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public
utility commission, public service commission or corporation commission for
information.
If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this equipment does not disable your alarm equipment. If
you have questions about what will disable alarm equipment, consult your
telephone company or a qualified installer.
WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS TO
EMERGENCY NUMBERS:
1) Remain on the line and briefly explain to the dispatcher the reason for the call.
2) Perform such activities in the off-peak hours, such as early morning or late
evenings.
IC CS-03 Statement
''NOTICE: This equipment meets the applicable Industry Canada Terminal
Equipment Technical Specifications. This is confirmed by the registration number.
The abbreviation, IC, before the registration number signifies that registration was
performed based on a Declaration of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that Industry Canada approved
the equipment.”
''NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.3.
The REN assigned to each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface.
The termination on an interface may consist of any combination of devices subject
only to the requirement that the sum of the Ringer Equivalence Numbers of all the
devices does not exceed five.''
~63~
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Annotate, Fill forms, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : GPL Ghostscript 9.05
Keywords                        : 
Modify Date                     : 2012:12:12 09:40:19+08:00
Create Date                     : 2012:12:05 17:26:35+08:00
Creator Tool                    : PDFCreator Version 1.5.0
Metadata Date                   : 2012:12:12 09:40:19+08:00
Document ID                     : uuid:5e866b73-4119-11e2-0000-0f9d5e36f36f
Instance ID                     : uuid:dd7be4ee-3dfe-4109-949c-70c38e792857
Format                          : application/pdf
Title                           : FreeStyl 2_User Manual_English_Dec052012
Creator                         : 100237
Description                     : ()
Page Count                      : 32
Subject                         : 
Author                          : 100237
EXIF Metadata provided by EXIF.tools
FCC ID Filing: U2M-FS2

Navigation menu