Senao Networks PCE3200AH 802.11 bgn PCle Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1890847
Application ID	P6psaQAZry2x1YnIanCQqw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.64kB (170491 bits)
Date Submitted	2013-01-31 00:00:00
Date Available	2013-01-31 00:00:00
Creation Date	2017-10-28 14:09:24
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-28 14:09:24
Document Title	Microsoft Word - PCE3200AH user's manual_bgn_-0131-ok.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	VeraHsu

802.11n/ b/ g PCI e Module
PCE3200AH
User’s Manual
FCC Certification
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user authority to operate the
equipment.
CAU T I ON
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other
channels is not possible.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna
or transmitter.
Integration Manual: Antenna Info (list of approved antennas) generally required for modular approved
transmitters with external antennas
Ant.
Brand
Model Name
Master Wave Technology CO., LTD
98618MNXX001
Master Wave Technology CO., LTD
98618MNXX001
Master Wave Technology CO., LTD
98618MNXX001
No te : The EUT ha s thre e a nte nna s. (3TX/ 3RX)
Antenna Type
Connector
Gain (dBi)
Dipole Antenna
Dip o le Ante nna
Dip o le Ante nna
MMCX
MMCX
MMCX
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC
compliance requirement of the end product, which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users for the
host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth
for an population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm
separation with the antenna while this end product is installed and operated. The end user has to be
informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be
satisfied. The end user has to also be informed that any changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate this equipment. If the size of the
end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be
available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: U2M-PCE3200AH ".
If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be
available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Table of Contents
CHAPTER 1: I NTRODUCTI ON ..........................................................1
FEATURES ................................................................................................1
PHYSI CAL DETAI LS.....................................................................................1
CHAPTER 2: I NSTALLATI ON.............................................................1
FOR WI NDOWS 2000/ XP ...........................................................................1
I nstall Software ................................................................................................................. 1
I nstall Hardware................................................................................................................ 2
Verification ......................................................................................................................... 2
FOR WI NDOWS VI STA ................................................................................2
I nstall Software ................................................................................................................. 2
I nstall Hardware................................................................................................................ 2
Verification ......................................................................................................................... 3
FOR WI NDOWS 7 ......................................................................................3
I nstall Software ................................................................................................................. 3
I nstall Hardware................................................................................................................ 3
Verification ......................................................................................................................... 3
CHAPTER 3: NETWORK CONNECTI ON .........................................4
HOW TO MAKE A CONNECTI ON ....................................................................4
HOW TO ADD A PROFI LE.............................................................................4
CHAPTER 4: UTI LI TY CONFI GURATI ON ......................................5
FOR WI NDOWS 2000/ XP ...........................................................................5
Station Mode ..................................................................................................................... 5
Switch to AP Mode .......................................................................................................... 10
Soft AP mode ................................................................................................................... 10
FOR WI NDOWS VI STA ..............................................................................12
Station Mode ................................................................................................................... 12
Switch to AP Mode .......................................................................................................... 17
Soft AP mode ................................................................................................................... 17
FOR WI NDOWS 7 ....................................................................................18
Station Mode ................................................................................................................... 18
Switch to AP Mode .......................................................................................................... 23
Soft AP mode ................................................................................................................... 23
CHAPTER 5: UNI NSTALL..................................................................25
FOR WI NDOWS 2000/ XP .........................................................................25
FOR WI NDOWS VI STA ..............................................................................25
FOR WI NDOWS 7 ....................................................................................25
Chapter 1:
I ntroduction
PCE3200AH measures just around 15 mm long and 15mm wide that make it hold the distinction of
being the smallest USB dongle in the world at present. PCE3200AH give mobile workers the freedom
of staying connected to the network while roaming around a building or multiple buildings maintaining
access to the Internet, e-mail, networked applications with the best convenience in narrow or crowded
space for it’s ultra micro size.PCE3200AH is expected to be able to reach 150Mbps, which is relatively
lower than normal, but still far more than sufficient to receive media streaming to the from access
point.
Features





3T3R Mode with 450Mbps PHY Rate
Complies with IEEE 802.11n and IEEE 802.11 b/g standards
Supports WEP 64/128, WPA, WPA2
Supports USB 2.0 interface
Chapter 2: I nstallation
For Window s 2000/ XP
I nstall Softw are
Note:
Do not insert the WLAN Module into the computer until the InstallShield
Wizard finished installing.
1. Exit all Windows programs. Insert the included Installation CD into the computer. The CD-ROM
will run automatically. Please click Next to process the installation.
2. When prompt to the following message, please click Install to begin the installation.
3. When the following screen appears, click Finish to restart the computer to complete the software
installation.
-1-
I nstall Hardw are
Note:
Insert the WLAN Module when finished software installation.
Insert the WLAN Module into the USB Port of the computer. The system will automatically detect the
new hardware.
Verification
To verify the device is active in the computer. Go to Start > Control Panel > System > Hardware>
Device Manager. Expand the Network adapters category. If the 802.11n/b/g 2cm Wireless LAN
USB2.0 Adapter is listed here, it means that the device is properly installed and enabled.
For Window s Vista
I nstall Softw are
Note:
Do not insert the WLAN Module into the computer until the InstallShield
Wizard finished installing.
1.
Exit all Windows programs. Insert the included Installation CD into the computer. The CD-ROM
will run automatically. Please click Next to process the installation.
2. When prompt to the following message, please click Install to begin the installation.
3.
When the following screen appears, click Finish to restart the computer to complete the software
installation.
I nstall Hardw are
Note:
Insert the WLAN Module when finished software installation.
Insert the WLAN Module into the USB Port of the computer. The system will automatically detect the
new hardware.
-2-
Verification
To verify the device is active in the computer. Go to Start >Control Panel > Hardware and
Sound > Device Manager. Expand the Network adapters category. If the 802.11n/b/g 2cm
Wireless LAN USB2.0 Adapter is listed here, it means that the device is properly installed and
enabled.
For Window s 7
I nstall Softw are
Note:
Do not insert the WLAN Module into the computer until the InstallShield
Wizard finished installing.
1. Exit all Windows programs. Insert the included Installation CD into the computer. The CD-ROM
will run automatically. Please click Next to process the installation.
2.
3.
When prompt to the following message, please click Install to begin the installation
When the following screen appears, click Finish to restart the computer to complete the software
installation.
I nstall Hardw are
Note:
Insert the WLAN Module when finished software installation.
Insert the WLAN Module into the USB Port of the computer. The system will automatically detect the
new hardware.
Verification
To verify the device is active in the computer. Go to Start > Control Panel > Device Manager.
Expand the Network adapters category. If the 802.11n/b/g 2cm Wireless LAN USB2.0 Adapter is
listed here, it means that the device is properly installed and enabled.
-3-
Chapter 3:
Netw ork Connection
How to Make a Connection
To make a connection with an access point, please follow below steps. Here takes Windows XP OS for
example.
Step 1: After set up the WLAN Module successfully, please launch the Configuration Utility.
There are two ways to launch the utility by:
(1) Double clicking the Intelligent Wireless LAN Utility icon on the desktop.
(2) Or go to Start All Programs Intelligent Wireless Utility  Intelligent Wireless LAN
Utility.
Step 2: Please go to the Available Network tab, the system will automatically scan access points
nearby, or click Refresh button to site survey again.
Step 3: Then, double click preferred access point or click Add to Profile button to make a
connection (if the access point has been set up security, please enter passwords and then click OK.)
How to Add a Profile
After launched Wireless LAN Utility and selected preferred access point, please click Add to Profile
button to enter Wireless Network Properties windows. If the access point has been set up security,
please enter passwords, and then click OK to save profile settings.
After finished above settings, please go to Profile tab to check the profile list (Available Profile(s)).
-4-
Chapter 4:
Utility Configuration
For Window s 2000/ XP
Station Mode
Show Tray Icon: Check to show the wireless adapter icon at the tray.
Disable Adapter: Check this to disable the wireless adapter.
Radio off: Check this to turn OFF radio function.
Close: Click to leave the Intelligent 11n USB Wireless LAN Utility.
General
The General page displays the detail information of current connection.
General Tab
Status
Shows the current connected status. If there is no connection, it will show
Not Associated. If been connected, the system will show Associated.
When connecting, the system will show checking Status.
Speed
Shows the current transmitting rate and receiving rate.
Type
Network type in use, Infrastructure or Ad-Hoc.
Encryption
Shows the encryption type currently in use. Valid value includes WEP,
TKIP, AES, and Not Use.
SSID
Shows the connected access point network name.
Signal Strength
Shows the receiving signal strength.
Link Quality
Shows the connection quality based on signal strength.
MAC Address
The physical address of the WLAN Module.
IP Address
Shows the IP address information.
Subnet Mask
Shows the Subnet Mask information.
Gateway
Shows the default gateway IP address.
Renew IP
Click the Renew IP button to obtain IP address form the connected
gateway.
-5-
Profile
Profile can let users book keeping the favorite wireless setting among home, office, and other public
hot-spot. Users may save multiple profiles, and activate the correct one at preference. The Profile
manager enables users to Add, Remove, Edit, Duplicate and Set Default profiles.
Profile Tab
Profile Name
Here shows a distinctive name of profile in this column.
SSID
The SSID is the unique name shared among all wireless access points in
the wireless network.
Add
Click Add button to add a profile from the drop-down screen.
Profile Name: Users can enter profile name at will.
Network Name (SSID): The SSID is the unique network name
(case-sensitive) shared among all wireless access points in the wireless
network. The name must be identical for all devices and wireless access
points attempting to connect to the same network.
This is a computer-to-computer (ad hoc) network; wireless access
points are not used: This function is selected to enable the ad hoc
network type that computers should be setup at the same channel to
communicate to each other directly without access point, users can share
files and printers between each PC and laptop. User can select channels
form the pull-down menu.
Wireless network security
Network Authentication: There are several types of authentication
modes including Open System, Shared Key, WPA-PSK, WPA2-PSK,
WPA 802.1X, WPA2 802.1X and WEP 802.1X.
Data encryption: For Open System, Shared Key and WEP 802.1X
authentication mode, the selection of encryption type is WEP. For
WPA-PSK, WPA2-PSK, WPA 802.1X and WPA2 802.1X authentication
mode, the encryption type supports both TKIP and AES.
When encryption is set to WEP…
ASCII: Only valid when using WEP encryption algorithm. When key
length is set to 64 bits user can enter 5 ASCII characters (case sensitive),
and 128 bits for 13 ASCII characters (case sensitive).
PASS PHRASE: Only valid when using WEP encryption algorithm.
When key length is set to 64 bits user can enter 10 Hexadecimal characters
(0~9, a~f) and 128 bits for 26 Hexadecimal characters (0~9, a~f).
Key index (advanced): Select 1~4 key index form the pull-down menu,
must match with the connected AP’s key index.
When encryption is set to WPA-PSK/ WPA2-PSK…
Network key: Enter network key at least 8 to 64 characters.
Confirm network key: Enter network key again to confirm.
When encryption is set to WPA 802.1X/ WPA2 802.1X/ WEP
-6-
802.1X…
When users use radius server to authenticate client certificate for WPA
authentication mode (WPA authentication do not support EAP MethodMD5-Challenge).
EAP TYPE:
 TLS: Transport Layer Security. Provides for certificate-based and
mutual authentication of the client and the network. It relies on
client-side and server-side certificates to perform authentication and
can be used to dynamically generate user-based and session-based
WEP keys to secure subsequent communications between the WLAN
client and the access point.
 LEAP: Light Extensible Authentication Protocol. It is an EAP
authentication type used primarily in Cisco Aironet WLANs. It
encrypts data transmissions using dynamically generated WEP keys,
and supports mutual authentication.
 TTLS: Tunnelled Transport Layer Security. This security method
provides for certificate-based, mutual authentication of the client and
network through an encrypted channel. Unlike EAP-TLS, EAP-TTLS
requires only server-side certificates.
 PEAP: Protect Extensible Authentication Protocol. PEAP transport
securely authentication data by using tunnelling between PEAP clients
and an authentication server. PEAP can authenticate wireless LAN
clients using only server-side certificates, thus simplifying the
implementation and administration of a secure wireless LAN.
 MD5:
Message Digest Challenge. Challenge is an EAP
authentication type that provides base-level EAP support. It
provides for only one-way authentication - there is no mutual
authentication of wireless client and the network.
Tunnel: This is enabled under TTLS and PEAP type. For TTLS, the
selections of tunnel are CHAP, MSCHAP, MSCHAP-V2, PAP. For PEAP,
the selections of tunnel are MD5, GTC, TLS and MSCHAP-V2.
Username: Enter the username for server.
Identity: Enter the identity for server.
Domain: Enter the domain of the network.
Password: Enter the password for server.
Certificate: Choose server that issuer of certificates.
Remove
Click Remove button to delete selected profile.
Edit
Click Edit button to edit selected profile.
Duplicate
Click Duplicate button to copy selected profile.
Set Default
Click Set Default button to set selected profile to be connected first.
-7-
Available Network
This page displays the information of surrounding APs from last scan result. The tab lists the
information including SSID, Channel, Encryption, Network Authentication, Signal, Type, BSSID,
Supported Rate (s), and Mode.
Network Tab
SSID
Shows the network name of the access points.
Channel
Shows the currently channel in use.
Encryption
Shows the encryption type currently in use. Valid value includes WEP,
TKIP, AES, None and TKIP/AES.
Network
Authentication
Show the device network authentication.
Signal
Shows transmit power, the amount of power used by a radio transceiver to
send the signal out.
Type
Network type in use, Infrastructure or Ad-Hoc mode.
BSSID
Shows Wireless MAC address.
Supported Rate(s)
Shows the transmitting data rate.
Mode
Supported wireless mode. It may support 802.11b, 802.11g and 802.11n
wireless mode.
Refresh
Click Refresh button to search and rescan the available network.
Add to Profile
Select an available network (SSID) on the list and then click Add to Profile
button to add it into the profile list.
Note
Double click on item to join/create profile.
Status
This tab listed the information about the WLAN Module and connected access point.
-8-
Statistics
The Statistics screen displays the statistics on the current network settings.
Statistics
Tx OK
Shows information of packets successfully sent.
Tx Error
Shows information of packets failed transmit after hitting retry
limit.
Rx OK
Shows information of packets received successfully.
Rx Packet Count
Shows information of packets received successfully.
Rx Retry
Shows information of packets failed transmit after hitting retry
limit.
Rx ICV Error
Shows information of packets received with ICV error.
Reset
Click to reset counters to zero.
WPS
The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to simplify the security
setup and management of Wi-Fi networks. The STA as an Enrollee or external Registrar supports the
configuration setup using PIN (Personal Identification Number) configuration method or PBC (Push
Button Configuration) method through an internal or external Registrar.
WPS Tab
PIN Code
8-digit numbers. It is required to enter PIN Code into Registrar when using
PIN method. When STA is Enrollee, users can use "Renew" button to
re-generate new PIN Code.
Pin Input Config
(PIN)
Click the Pin Input Config (PIN) button to select specific AP to process PIN
Config.
Push Button Config Click this button to connect with AP that supported WPS function within two
minutes. Meanwhile, the AP should also click the PBC button simultaneously.
(PBC)
-9-
About
This page displays the information of the WLAN Module Version.
Sw itch to AP Mode
To access the soft AP mode, please select the Mode on the function list of the Utility to make the
WLAN Module act as a wireless AP.
Soft AP mode
General
General
SSID
Shows the network name of the AP.
BSSID
Shows the MAC address of the AP.
Association Table
This table shows the connected client here.
Config
Click the Config button to set up the Wireless Network Properties.
Network Name (SSID): User can change the network name of this access
point.
Channel: User can select the channel form the pull-down list.
Wireless network security
Network Authentication: There are several types of authentication
modes including Open System, Shared Key, WPA-PSK and WPA2-PSK.
Data encryption: For Open System and Shared Key authentication mode,
the selection of encryption type is WEP. For WPA-PSK, WPA2-PSK,
authentication mode, the encryption type supports both TKIP and AES.
When encryption is set to WEP…
ASCII: Only valid when using WEP encryption algorithm. When key
length is set to 64 bits user can enter 5 ASCII characters (case sensitive),
and 128 bits for 13 ASCII characters (case sensitive).
PASS PHRASE: Only valid when using WEP encryption algorithm.
When key length is set to 64 bits user can enter 10 Hexadecimal characters
(0~9, a~f) and 128 bits for 26 Hexadecimal characters (0~9, a~f).
- 10 -
Key index (advanced): Select 1~4 key index form the pull-down menu,
must match with the connected AP’s key index.
When encryption is set to WPA-PSK/ WPA2-PSK…
Network key: Enter network key at least 8 to 64 characters.
Confirm network key: Enter network key again to confirm.
Advanced
Beacon Interval
The time between two beacons. (The system default is 100 ms.)
DTIM Period
The delivery traffic indication message (DTIM) is an element included in
some beacon frames. User can specify a value from 1 to 255 beacons.
Preamble
Select from the pull-down menu to change the Preamble type into Short
or Long.
Set Defaults
Click to use the system default value.
Apply
Click to apply the above settings.
tatistics
Tx OK
Shows information of packets successfully sent.
Tx Error
Shows information of packets failed transmit after hitting retry
limit.
Rx OK
Shows information of packets received successfully.
Rx Packet Count
Shows information of packets received successfully.
Rx Retry
Shows information of packets failed transmit after hitting retry
limit.
Rx ICV Error
Shows information of packets received with ICV error.
Reset
Click to reset counters to zero.
- 11 -
ICS
This page displays setting Internet connection sharing (ICS). Select a sharing public network and click
Apply button to make a connection.
For Window s Vista
Station Mode
Show Tray Icon: Check to show the wireless adapter icon at the tray.
Disable Adapter: Check this to disable the wireless adapter.
Radio off: Check this to turn OFF radio function.
Close: Click to leave the Intelligent 11n USB Wireless LAN Utility.
General
The General page displays the detail information of current connection.
General Tab
Status
Shows the current connected status. If there is no connection, it will show
Not Associated. If been connected, the system will show Associated.
When connecting, the system will show checking Status.
Speed
Shows the current transmitting rate and receiving rate.
Type
Network type in use, Infrastructure or Ad-Hoc.
Encryption
Shows the encryption type currently in use. Valid value includes WEP,
TKIP, AES, and Not Use.
SSID
Shows the connected access point network name.
Signal Strength
Shows the receiving signal strength.
Link Quality
Shows the connection quality based on signal strength.
MAC Address
The physical address of the WLAN Module.
IP Address
Shows the IP address information.
Subnet Mask
Shows the Subnet Mask information.
Gateway
Shows the default gateway IP address.
Renew IP
Click the Renew IP button to obtain IP address form the connected
gateway.
- 12 -
Profile
Profile can let users book keeping the favorite wireless setting among home, office, and other public
hot-spot. Users may save multiple profiles, and activate the correct one at preference. The Profile
manager enables users to Add, Remove, Edit, Duplicate and Set Default profiles.
Profile Tab
Profile Name
Here shows a distinctive name of profile in this column.
SSID
The SSID is the unique name shared among all wireless access points in
the wireless network.
Add
Click Add button to add a profile from the drop-down screen.
This is a computer-to-computer (ad hoc) network; wireless access
points are not used: This function is selected to enable the ad hoc
network type that computers should be setup at the same channel to
communicate to each other directly without access point, users can share
files and printers between each PC and laptop.
Profile Name: Users can enter profile name at will.
Network Name (SSID): The SSID is the unique network name
(case-sensitive) shared among all wireless access points in the wireless
network. The name must be identical for all devices and wireless access
points attempting to connect to the same network.
Channel: If set to ad hoc network type, user can select channels form the
pull-down menu.
Wireless network security
Network Authentication: There are several types of authentication
modes including Open System, Shared Key, WPA-PSK, WPA2-PSK,
WPA 802.1X, WPA2 802.1X and WEP 802.1X.
Data encryption: For Open System, Shared Key and WEP 802.1X
authentication mode, the selection of encryption type is WEP. For
WPA-PSK, WPA2-PSK, WPA 802.1X and WPA2 802.1X authentication
mode, the encryption type supports both TKIP and AES.
When encryption is set to WEP…
ASCII: Only valid when using WEP encryption algorithm. When key
length is set to 64 bits user can enter 5 ASCII characters (case sensitive),
and 128 bits for 13 ASCII characters (case sensitive).
PASS PHRASE: Only valid when using WEP encryption algorithm.
When key length is set to 64 bits user can enter 10 Hexadecimal characters
(0~9, a~f) and 128 bits for 26 Hexadecimal characters (0~9, a~f).
Key index (advanced): Select 1~4 key index form the pull-down menu,
must match with the connected AP’s key index.
When encryption is set to WPA-PSK/ WPA2-PSK…
Network key: Enter network key at least 8 to 64 characters.
- 13 -
Confirm network key: Enter network key again to confirm.
When encryption is set to WPA 802.1X/ WPA2 802.1X/ WEP
802.1X…
When users use radius server to authenticate client certificate for WPA
authentication mode (WPA authentication do not support EAP MethodMD5-Challenge).
EAP TYPE:
 TLS: Transport Layer Security. Provides for certificate-based and
mutual authentication of the client and the network. It relies on
client-side and server-side certificates to perform authentication and
can be used to dynamically generate user-based and session-based
WEP keys to secure subsequent communications between the WLAN
client and the access point.
 LEAP: Light Extensible Authentication Protocol. It is an EAP
authentication type used primarily in Cisco Aironet WLANs. It
encrypts data transmissions using dynamically generated WEP keys,
and supports mutual authentication.
 TTLS: Tunnelled Transport Layer Security. This security method
provides for certificate-based, mutual authentication of the client and
network through an encrypted channel. Unlike EAP-TLS, EAP-TTLS
requires only server-side certificates.
 PEAP: Protect Extensible Authentication Protocol. PEAP transport
securely authentication data by using tunnelling between PEAP clients
and an authentication server. PEAP can authenticate wireless LAN
clients using only server-side certificates, thus simplifying the
implementation and administration of a secure wireless LAN.
 MD5:
Message Digest Challenge. Challenge is an EAP
authentication type that provides base-level EAP support. It
provides for only one-way authentication - there is no mutual
authentication of wireless client and the network.
Tunnel: This is enabled under TTLS and PEAP type. For TTLS, the
selections of tunnel are CHAP, MSCHAP, MSCHAP-V2, PAP. For PEAP,
the selections of tunnel are MD5, GTC, TLS and MSCHAP-V2.
Username: Enter the username for server.
Identity: Enter the identity for server.
Domain: Enter the domain of the network.
Password: Enter the password for server.
Certificate: Choose server that issuer of certificates.
Remove
Click Remove button to delete selected profile.
Edit
Click Edit button to edit selected profile.
Duplicate
Click Duplicate button to copy selected profile.
Set Default
Click Set Default button to set selected profile to be connected first.
- 14 -
Available Network
This page displays the information of surrounding APs from last scan result. The tab lists the
information including SSID, Channel, Encryption, Network Authentication, Signal, Type, BSSID,
Supported Rate(s), and Mode.
Network Tab
SSID
Shows the network name of the access points.
Channel
Shows the currently channel in use.
Encryption
Shows the encryption type currently in use. Valid value includes WEP, TKIP,
AES, None and TKIP/AES.
Network
Authentication
Show the device network authentication.
Signal
Shows transmit power, the amount of power used by a radio transceiver to
send the signal out.
Type
Network type in use, Infrastructure or Ad-Hoc mode.
BSSID
Shows Wireless MAC address.
Supported Rate(s)
Shows the transmitting data rate.
Mode
Supported wireless mode. It may support 802.11b, 802.11g and 802.11n
wireless mode.
Refresh
Click Refresh button to search and rescan the available network.
Add to Profile
Select an available network (SSID) on the list and then click Add to Profile
button to add it into the profile list.
Note
Double click on item to join/create profile.
Status
This tab listed the information about the WLAN Module and connected access point.
Statistics
The Statistics screen displays the statistics on the current network settings.
- 15 -
Statistics
Tx OK
Shows information of packets successfully sent.
Tx Error
Shows information of packets failed transmit after hitting retry
limit.
Rx OK
Shows information of packets received successfully.
Rx Packet Count
Shows information of packets received successfully.
Rx Retry
Shows information of packets failed transmit after hitting retry
limit.
Rx ICV Error
Shows information of packets received with ICV error.
Reset
Click to reset counters to zero.
WPS
The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to simplify the security
setup and management of Wi-Fi networks. The STA as an Enrollee or external Registrar supports the
configuration setup using PIN (Personal Identification Number) configuration method or PBC (Push
Button Configuration) method through an internal or external Registrar.
WPS Tab
PIN Code
8-digit numbers. It is required to enter PIN Code into Registrar when using
PIN method. When STA is Enrollee, users can use "Renew" button to
re-generate new PIN Code.
Pin Input Config
(PIN)
Click the Pin Input Config (PIN) button to select specific AP to process PIN
Config.
Push Button Config Click this button to connect with AP that supported WPS function within two
minutes. Meanwhile, the AP should also click the PBC button simultaneously.
(PBC)
About
This page displays the information of the WLAN Module Version.
- 16 -
Sw itch to AP Mode
To access the soft AP mode, please select the Mode on the function list of the Utility to make the
WLAN Module act as a wireless AP.
Soft AP mode
General
SSID
Shows the network name of the AP.
BSSID
Shows the MAC address of the AP.
Association Table
This table shows the connected client here.
Config
Click the Config button to set up the Wireless Network Properties.
Network Name (SSID): User can change the network name of this access
point.
Channel: User can select the channel form the pull-down list.
Wireless network security
Network Authentication: There are several types of authentication
modes including Open System, Shared Key, WPA-PSK and WPA2-PSK.
Data encryption: For Open System and Shared Key authentication mode,
the selection of encryption type is WEP. For WPA-PSK, WPA2-PSK,
authentication mode, the encryption type supports both TKIP and AES.
When encryption is set to WEP…
ASCII: Only valid when using WEP encryption algorithm. When key
length is set to 64 bits user can enter 5 ASCII characters (case sensitive),
and 128 bits for 13 ASCII characters (case sensitive).
PASS PHRASE: Only valid when using WEP encryption algorithm.
When key length is set to 64 bits user can enter 10 Hexadecimal characters
(0~9, a~f) and 128 bits for 26 Hexadecimal characters (0~9, a~f).
Key index (advanced): Select 1~4 key index form the pull-down menu,
must match with the connected AP’s key index.
When encryption is set to WPA-PSK/ WPA2-PSK…
Network key: Enter network key at least 8 to 64 characters.
Confirm network key: Enter network key again to confirm.
- 17 -
Advanced
Advanced
Beacon Interval
The time between two beacons. (The system default is 100 ms.)
DTIM Period
The delivery traffic indication message (DTIM) is an element included in
some beacon frames. User can specify a value from 1 to 255 beacons.
Preamble
Select from the pull-down menu to change the Preamble type into Short
or Long.
Set Defaults
Click to use the system default value.
Apply
Click to apply the above settings.
Statistics
Tx OK
Shows information of packets successfully sent.
Tx Error
Shows information of packets failed transmit after hitting retry
limit.
Rx OK
Shows information of packets received successfully.
Rx Packet Count
Shows information of packets received successfully.
Rx Retry
Shows information of packets failed transmit after hitting retry
limit.
Rx ICV Error
Shows information of packets received with ICV error.
Reset
Click to reset counters to zero.
ICS
This page displays setting Internet connection sharing (ICS). Select a sharing public network and click
Apply button to make a connection.
For Window s 7
Station Mode
Show Tray Icon: Check to show the wireless adapter icon at the tray.
Disable Adapter: Check this to disable the wireless adapter.
Radio off: Check this to turn OFF radio function.
Close: Click to leave the Intelligent 11n USB Wireless LAN Utility.
- 18 -
General
The General page displays the detail information of current connection.
General Tab
Status
Shows the current connected status. If there is no connection, it will show
Not Associated. If been connected, the system will show Associated.
When connecting, the system will show checking Status.
Speed
Shows the current transmitting rate and receiving rate.
Type
Network type in use, Infrastructure or Ad-Hoc.
Encryption
Shows the encryption type currently in use. Valid value includes WEP,
TKIP, AES, and Not Use.
SSID
Shows the connected access point network name.
Signal Strength
Shows the receiving signal strength.
Link Quality
Shows the connection quality based on signal strength.
MAC Address
The physical address of the WLAN Module.
IP Address
Shows the IP address information.
Subnet Mask
Shows the Subnet Mask information.
Gateway
Shows the default gateway IP address.
Renew IP
Click the Renew IP button to obtain IP address form the connected
gateway.
Profile
Profile can let users book keeping the favorite wireless setting among home, office, and other public
hot-spot. Users may save multiple profiles, and activate the correct one at preference. The Profile
manager enables users to Add, Remove, Edit, Duplicate and Set Default profiles.
Profile Tab
Profile Name
Here shows a distinctive name of profile in this column.
SSID
The SSID is the unique name shared among all wireless access points in
the wireless network.
Add
Click Add button to add a profile from the drop-down screen.
This is a computer-to-computer (ad hoc) network; wireless access
points are not used: This function is selected to enable the ad hoc
network type that computers should be setup at the same channel to
communicate to each other directly without access point, users can share
files and printers between each PC and laptop.
Profile Name: Users can enter profile name at will.
Network Name (SSID): The SSID is the unique network name
(case-sensitive) shared among all wireless access points in the wireless
network. The name must be identical for all devices and wireless access
- 19 -
points attempting to connect to the same network.
Channel: If set to ad hoc network type, user can select channels form the
pull-down menu.
Wireless network security
Network Authentication: There are several types of authentication
modes including Open System, Shared Key, WPA-PSK, WPA2-PSK,
WPA 802.1X, WPA2 802.1X and WEP 802.1X.
Data encryption: For Open System, Shared Key and WEP 802.1X
authentication mode, the selection of encryption type is WEP. For
WPA-PSK, WPA2-PSK, WPA 802.1X and WPA2 802.1X authentication
mode, the encryption type supports both TKIP and AES.
When encryption is set to WEP…
ASCII: Only valid when using WEP encryption algorithm. When key
length is set to 64 bits user can enter 5 ASCII characters (case sensitive),
and 128 bits for 13 ASCII characters (case sensitive).
PASS PHRASE: Only valid when using WEP encryption algorithm.
When key length is set to 64 bits user can enter 10 Hexadecimal characters
(0~9, a~f) and 128 bits for 26 Hexadecimal characters (0~9, a~f).
Key index (advanced): Select 1~4 key index form the pull-down menu,
must match with the connected AP’s key index.
When encryption is set to WPA-PSK/ WPA2-PSK…
Network key: Enter network key at least 8 to 64 characters.
Confirm network key: Enter network key again to confirm.
When encryption is set to WPA 802.1X/ WPA2 802.1X/ WEP
802.1X…
When users use radius server to authenticate client certificate for WPA
authentication mode (WPA authentication do not support EAP MethodMD5-Challenge).
EAP TYPE:
 TLS: Transport Layer Security. Provides for certificate-based and
mutual authentication of the client and the network. It relies on
client-side and server-side certificates to perform authentication and
can be used to dynamically generate user-based and session-based
WEP keys to secure subsequent communications between the WLAN
client and the access point.
 LEAP: Light Extensible Authentication Protocol. It is an EAP
authentication type used primarily in Cisco Aironet WLANs. It
encrypts data transmissions using dynamically generated WEP keys,
and supports mutual authentication.
 TTLS: Tunnelled Transport Layer Security. This security method
provides for certificate-based, mutual authentication of the client and
network through an encrypted channel. Unlike EAP-TLS, EAP-TTLS
requires only server-side certificates.
 PEAP: Protect Extensible Authentication Protocol. PEAP transport
securely authentication data by using tunnelling between PEAP clients
and an authentication server. PEAP can authenticate wireless LAN
- 20 -
clients using only server-side certificates, thus simplifying the
implementation and administration of a secure wireless LAN.
 MD5:
Message Digest Challenge. Challenge is an EAP
authentication type that provides base-level EAP support. It
provides for only one-way authentication - there is no mutual
authentication of wireless client and the network.
Tunnel: This is enabled under TTLS and PEAP type. For TTLS, the
selections of tunnel are CHAP, MSCHAP, MSCHAP-V2, PAP. For PEAP,
the selections of tunnel are MD5, GTC, TLS and MSCHAP-V2.
Username: Enter the username for server.
Identity: Enter the identity for server.
Domain: Enter the domain of the network.
Password: Enter the password for server.
Certificate: Choose server that issuer of certificates.
Remove
Click Remove button to delete selected profile.
Edit
Click Edit button to edit selected profile.
Duplicate
Click Duplicate button to copy selected profile.
Set Default
Click Set Default button to set selected profile to be connected first.
Available Network
This page displays the information of surrounding APs from last scan result. The tab lists the
information including SSID, Channel, Encryption, Network Authentication, Signal, Type, BSSID,
Supported Rate(s), and Mode.
Network Tab
SSID
Shows the network name of the access points.
Channel
Shows the currently channel in use.
Encryption
Shows the encryption type currently in use. Valid value includes WEP, TKIP,
AES, None and TKIP/AES.
Network
Authentication
Show the device network authentication.
Signal
Shows transmit power, the amount of power used by a radio transceiver to
send the signal out.
Type
Network type in use, Infrastructure or Ad-Hoc mode.
BSSID
Shows Wireless MAC address.
Supported Rate(s)
Shows the transmitting data rate.
Mode
Supported wireless mode. It may support 802.11b, 802.11g and 802.11n
- 21 -
wireless mode.
Refresh
Click Refresh button to search and rescan the available network.
Add to Profile
Select an available network (SSID) on the list and then click Add to Profile
button to add it into the profile list.
Note
Double click on item to join/create profile.
Status
This tab listed the information about the WLAN Module and connected access point.
Statistics
The Statistics screen displays the statistics on the current network settings.
Statistics
Tx OK
Shows information of packets successfully sent.
Tx Error
Shows information of packets failed transmit after hitting retry
limit.
Rx OK
Shows information of packets received successfully.
Rx Packet Count
Shows information of packets received successfully.
Rx Retry
Shows information of packets failed transmit after hitting retry
limit.
Rx ICV Error
Shows information of packets received with ICV error.
Reset
Click to reset counters to zero.
WPS
The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to simplify the security
setup and management of Wi-Fi networks. The STA as an Enrollee or external Registrar supports the
configuration setup using PIN (Personal Identification Number) configuration method or PBC (Push
Button Configuration) method through an internal or external Registrar.
WPS Tab
PIN Code
8-digit numbers. It is required to enter PIN Code into Registrar when using
PIN method. When STA is Enrollee, users can use "Renew" button to
re-generate new PIN Code.
Pin Input Config
(PIN)
Click the Pin Input Config (PIN) button to select specific AP to process PIN
Config.
Push Button Config Click this button to connect with AP that supported WPS function within two
minutes. Meanwhile, the AP should also click the PBC button simultaneously.
(PBC)
- 22 -
About
This page displays the information of the WLAN Module Version.
Sw itch to AP Mode
To access the soft AP mode, please select the Mode on the function list of the Utility to make the
WLAN Module act as a wireless AP.
Soft AP mode
General
General
SSID
Shows the network name of the AP.
BSSID
Shows the MAC address of the AP.
Association Table
This table shows the connected client here.
Config
Click the Config button to set up the Wireless Network Properties.
Network Name (SSID): User can change the network name of this access
point.
Channel: User can select the channel form the pull-down list.
Wireless network security
Network Authentication: There are several types of authentication
modes including Open System, Shared Key, WPA-PSK and WPA2-PSK.
Data encryption: For Open System and Shared Key authentication mode,
the selection of encryption type is WEP. For WPA-PSK, WPA2-PSK,
authentication mode, the encryption type supports both TKIP and AES.
When encryption is set to WEP…
ASCII: Only valid when using WEP encryption algorithm. When key
length is set to 64 bits user can enter 5 ASCII characters (case sensitive),
and 128 bits for 13 ASCII characters (case sensitive).
PASS PHRASE: Only valid when using WEP encryption algorithm.
When key length is set to 64 bits user can enter 10 Hexadecimal characters
(0~9, a~f) and 128 bits for 26 Hexadecimal characters (0~9, a~f).
Key index (advanced): Select 1~4 key index form the pull-down menu,
must match with the connected AP’s key index.
When encryption is set to WPA-PSK/ WPA2-PSK…
Network key: Enter network key at least 8 to 64 characters.
Confirm network key: Enter network key again to confirm.
- 23 -
Advanced
Advanced
Beacon Interval
The time between two beacons. (The system default is 100 ms.)
DTIM Period
The delivery traffic indication message (DTIM) is an element included in
some beacon frames. User can specify a value from 1 to 255 beacons.
Preamble
Select from the pull-down menu to change the Preamble type into Short
or Long.
Set Defaults
Click to use the system default value.
Apply
Click to apply the above settings.
Statistics
Statistics
Tx OK
Shows information of packets successfully sent.
Tx Error
Shows information of packets failed transmit after hitting retry
limit.
Rx OK
Shows information of packets received successfully.
Rx Packet Count
Shows information of packets received successfully.
Rx Retry
Shows information of packets failed transmit after hitting retry
limit.
Rx ICV Error
Shows information of packets received with ICV error.
Reset
Click to reset counters to zero.
ICS
This page displays setting Internet connection sharing (ICS). Select a sharing public network and click
Apply button to make a connection.
- 24 -
Chapter 5: Uninstall
For Window s 2000/ XP
To remove the utility and driver, please refer to below steps. (When removing the utility, the driver will
be removed as well.)
1.
Go to Start All Programs Intelligent Wireless Utility Uninstall –Intelligent.
2.
Click Yes to completely remove the selected application and all of its features.
3.
Then click Finish to complete uninstall.
For Window s Vista
To remove the utility and driver, please refer to below steps. (When removing the utility, the driver will
be removed as well.)
1.
Go to Start  Programs Intelligent Wireless LAN Utility Uninstall –Intelligent.
2.
Click Yes to complete remove the selected application and all of its features.
3.
Finally, click Finish to complete uninstall.
For Window s 7
To remove the utility and driver, please refer to below steps. (When removing the utility, the driver will
be removed as well.)
1.
Go to Start  Programs Intelligent Wireless Utility Uninstall –Intelligent.
2.
Click Yes to complete remove the selected application and all of its features.
3.
Finally, click Finish to complete uninstall.
- 25 -

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : VeraHsu
Create Date                     : 2013:01:31 12:00:01+08:00
Modify Date                     : 2013:01:31 12:50:47+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.5.3 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2013:01:31 12:50:47+08:00
Format                          : application/pdf
Title                           : Microsoft Word - PCE3200AH user's manual_bgn_-0131-ok.doc
Creator                         : VeraHsu
Document ID                     : uuid:b1f4ff4e-2083-44b5-8a1a-4302be4c4406
Instance ID                     : uuid:010f63ad-d5ca-4c14-9bd3-42803e2f87ef
State                           : 1
Version                         : 1.1
Page Count                      : 30

EXIF Metadata provided by EXIF.tools