Senao Networks PCE4302AN 802.11 ac 2x2 Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3826285
Application ID	q8/lWfMu/FS+XT6paEjwxg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	36.15kB (451892 bits)
Date Submitted	2018-04-23 00:00:00
Date Available	2018-05-02 00:00:00
Creation Date	2018-04-02 15:00:51
Producing Software	Microsoft® Word 2010
Document Lastmod	2018-04-03 14:31:45
Document Title	Users Manual
Document Creator	Microsoft® Word 2010
Document Author:	Windows User

User’s Manual
Model : PCE4302AN
1. Introduction
2.4 / 5 GHz
802.11a/b/g/n/ac
PCE4302AN
867Mbps
The PCE4302AN is adapting the next
generation 2-Stream Wi-Fi technology,
802.11ac. It provides the great improvement
in the performance compared with 802.11n
and achieves wireless performance of up to
867Mbps.
PCE4302AN is a dual band PCIe module to
support both 2.4Ghz and 5Ghz bands.
2. Feature


PCE4302AN
802.11a/b/g/n/ac dual band operation in the 2.4GHz and 5GHz frequency
bands.
Support WPA, TKIP, AES and WAPI hardware-based IEEE 802.11i encryption
engine
3. Hardware Installation
PCE4302AN
3-1. Installation Overview
PCE4302AN wireless module is design for Access Point, Router, IP Cam series and
Network products.
3.2 Safety Recommendations
The safety guidelines are as follows:
 Keep the board area clear and dust-free before, during, and after installation.
 Keep tools away from walk area where you and others could fall over them.
 Do not wear lose clothing or jewelry, such as earrings, bracelets hat could get
caught in the board
 Wear safety glasses if you are working under any conditions that might be
hazardous to your eyes.
 Do not perform any action that creates a potential hazard to people or makes the
equipment unsafe.
 Never attempt to lift an object that is too heavy for one person to handle.
3.3 Maintaining Safety with Electricity
Warning: Before working on a board or working near power supplies, unplug the
power cord on AC units; on DC unit, disconnect the power at the circuit breaker.
Follow these guidelines when working on equipment powered by electricity:
- Do not work alone if potentially hazardous conditions exist anywhere in your
work space.
- Never assume that power is disconnected from a circuit; always check the circuit.
- Extension cables, frayed power cords, and missing safety grounds. If an electrical
accident occurs, proceed as follows:
- Use caution; do not become a victim yourself
- Disconnect power from the system
If possible, send another person to get medical aid. Otherwise, access the
condition of the victim and then call for help.
Determine if the person needs rescue breathing or external cardiac compressions;
then take appropriate action.
3.4 Installing
- Remove the module from its protective packaging
- Avoiding Electrostatic Discharge
- Before your install the module, ground yourself by touching a piece of metal to
avoid electrostatic discharge (EDS).
You shall be able to take the following precautions to prevent damage to the module:
Keep module in its antistatic-shielded bag until you are ready to install it.
Handle the module by its edges.
Ensure the connector is connected to above Model’s board tightly.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your
body.
This device is intended only for OEM integrators under the following
conditions:
1) The antenna must be installed such that 20 cm is maintained
between the antenna and users, and
2) The transmitter module may not be co-located with any other
transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not
be required. However, the OEM integrator is still responsible for testing
their end-product for any additional compliance requirements required
with this module installed
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain
laptop configurations or co-location with another transmitter), then the
FCC authorization is no longer considered valid and the FCC ID can not
be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the
antenna may be installed such that 20 cm may be maintained between
the antenna and users. The final end product must be labeled in a
visible area with the following: “Contains FCC ID: U2M-PCE4302AN”.
The grantee's FCC ID can be used only when all FCC compliance
requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the
end user regarding how to install or remove this RF module in the user’s
manual of the end product which integrates this module.
The end user manual shall include all required regulatory
information/warning as show in this manual.
Industry Canada statement:
This device complies with RSS-247 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-247 d'Industrie Canada applicable
aux appareils radio exempts de licence. Son fonctionnement est sujet aux
deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris
un brouillage susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 22cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC
établies pour un environnement non contrôlé. Cet équipement doit être installé
et utilisé avec un minimum de 22 cm de distance entre la source de
rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions:
(For module device use)
1) The antenna must be installed such that 22 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les
conditions suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 22 cm est
respectée entre l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou
antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires
sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est
toujours responsable des essais sur son produit final pour toutes exigences de
conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada
authorization is no longer considered valid and the IC ID cannot be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour
certaines configurations d'ordinateur portable ou de certaines co-localisation
avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme
valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces
circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y
compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 22 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the following:
“Contains IC: 7280B-120512”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un
dispositif où l'antenne peut être installée de telle sorte qu'une distance de
22cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final
doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient
des IC: 7280B-120512".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à
l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF
dans le manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations
réglementaires requises et avertissements comme indiqué dans ce manuel.
Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz
shall be such that the equipment still complies with the e.i.r.p. limits specified for
point-to-point and non-point-to-point operation as appropriate; and
(iii) Users should also be advised that high-power radars are allocated as primary
users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could
cause interference and/or damage to LE-LAN devices.
Avertissement:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5
850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à
point et l’exploitation non point à point, selon le cas;
(iii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars
de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité)
pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage
et/ou des dommages aux dispositifs LAN-EL.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2018:04:02 15:00:51+08:00
Creator Tool                    : Microsoft® Word 2010
Modify Date                     : 2018:04:03 14:31:45+08:00
Metadata Date                   : 2018:04:03 14:31:45+08:00
Format                          : application/pdf
Creator                         : Windows User
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:ed2b42ca-ff10-449c-a10e-c69a68fd5546
Instance ID                     : uuid:6f6bd489-d819-43b0-a473-d37ab2c626b9
Page Count                      : 9
Language                        : zh-TW
Author                          : Windows User

EXIF Metadata provided by EXIF.tools