Senstar E7EM0201 Wireless Gate Sensor User Manual

Senstar Corporation Wireless Gate Sensor Wireless Gate Sensor

a href="https://usermanual.wiki/Senstar" itemprop="url"> Senstar >

User Manual

FlexZone Wireless Gate Sensor Page 1FlexZone™Instruction sheet #6G6DA0603-001, Rev ADecember 15, 2015DescriptionThe Wireless Gate Sensor (WGS) operates in conjunction with the FlexZone processor to provide RF-based wireless security protection for gates. The WGS is comprised of two components. The wireless gate sensor module (GSM) a high-sensitivity accelerometer, is attached to the protected gate. The GSM analyzes signals picked up from the fence fabric on the gate and will transmit an alarm when it detects vibration, motion, or positional changes. A wireless gate sensor receiver (GSR) that is mounted on the FlexZone processor receives the transmission and passes on the alarm signal to the FlexZone processor. Alarm data communications are via the FlexZone processor over the Silver Network or by contact closures. Features• 300 m (984 ft.) (nominal) transmission range with the supplied rubber whip antenna (requires direct line of sight)• secure RF transmissions via 128-bit encryption• supervised comm-link (heartbeat monitor, 2 missed transmissions = supervision alarm)Note Setup and operation of the WGS requires as a minimum, Network Manager version 2.20, UCM version 1.37 and FlexZone version 2.4 software.Figure 1 FlexZone Wireless Gate Sensor Module (solar powered)solar powered GSM mounted on sliding gatestainless steel cable ties (2 per side)no connection toauxiliary security deviceWireless Gate Sensor
Specifications Rev APage 2 FlexZone Wireless Gate Sensor• three selectable GSM supervision modes which are based on the position and orientation of the gate sensor module• supervised input for auxiliary device alarm reporting (e.g., magnetic contact)• solar powered - requires 2 hrs indirect sunlight per day (nominal) 5 days run time with no light (from fully charged)• 1 year (nominal) runtime using alkaline D-cell battery; 2+ years using lithium D-cell battery• low power notification transmitted at 25% capacity (solar) 10% capacity (D-cell battery)• emergency backup battery - 30 days run time (nominal)• user-configurable detection parameters and target filters• up to 4 GSMs can report to one receiver• each receiver provides 8 distinct channels (up to 32 GSMs per site - requires 8 FlexZone processors)Specifications• power consumption: GSM 3 mW (avg) GSR 0.5 W• operating voltage: solar / 1.5 V alkaline D-cell battery* OR 3.6 V lithium D-cell battery** battery type and voltage user selectable via shunt on T8 (see Figure 10)• detection frequency response: 0.1 to 400 Hz• transmission range: 300 m (984 ft.) (nominal) requires direct unobstructed line of site • coverage area: 1 to 5 gate panels depending on the height, width, type, and quality of the gateComplianceCanada: Industry Canada Identification Number: Gate Sensor Module 1454B-E7EM0201; Gate Sensor Receiver 1454B-E7BA0300This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Ce dispositif est conforme aux normes CNR d’Industrie Canada applicables aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes : 1) le dispositif ne doit pas produire de brouillage préjudiciable; et 2) il doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. USA: FCC Identification Number: Gate Sensor Module 15T-E7EM0201; Gate Sensor Receiver 15T-E7BA0300Changes or modifications not expressly approved by Senstar Corporation could void the user's authority to operate the equipment.FCC Certification - This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be Note The number of GSMs required to protect a gate varies with the type and size of the gate being protected. To determine the required number of GSMs, install one in a central position and test the gate. If the coverage is inadequate, install two GSMs at a central height and at 1/3 and 2/3 of the width and test the gate. Continue this process until your detection requirements are met (maximum of 4 GSMs per gate).
Download:
Mirror Download [FCC.gov]
Document ID2960459
Application IDGo8GKZ5UlovbTHWOsJAeEw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize113.4kB (1417530 bits)
Date Submitted2016-04-15 00:00:00
Date Available2016-04-15 00:00:00
Creation Date1996-03-12 17:37:42
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2016-01-21 11:07:37
Document TitleWireless Gate Sensor
Document CreatorFrameMaker 12.0.3
Document Author: Senstar
FCC ID Filing: I5TE7EM0201

Navigation menu