Sensus Metering Systems AMDS1000TR Fixed Microwave Services User Manual 04 0166 User Guide Cover
Sensus Metering Systems Inc. Fixed Microwave Services 04 0166 User Guide Cover
users manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 462894 |
| Application ID | BFFWJWOTf38sAa5gx32DIA== |
| Document Description | users manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 7.77kB (97159 bits) |
| Date Submitted | 2004-08-25 00:00:00 |
| Date Available | 2004-08-25 00:00:00 |
| Creation Date | 2004-08-13 18:11:19 |
| Producing Software | Acrobat Distiller 5.0.5 (Windows) |
| Document Lastmod | 2004-08-13 14:11:52 |
| Document Title | Microsoft Word - 04-0166 User Guide Cover.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | Michael Proffitt |
Narrowband PCS Transmitter Certification Test Report Model: AMDS-1000TR FCC ID: SDBAMDS1000TR ACS Report Number: 04-0166-24D Installation / User’s Guide Model: AMDS-1000TR Advanced Compliance Solutions FCCID: SDBAMDS1000TR AMDS iCon AMR Electric Meter Installation Guidelines Draft Copy INTRODUCTION: The following document briefly describes the installation of an AMDS iCon Transceiver equipped power meter. The scope of the document is to describe how to program the meter after proper installation by trained utility company technicians or licensed electricians. THIS METER IS ONLY TO BE INSTALLED BY QUALIFIED PERSONNEL! PROCEDURE: Confirm that the meter has been installed by a qualified entity or individual. Turn on the hand-held meter-programming device. (Either the Palm “Zire” or customized programming device supplied by utility). Select “Program Electric Meter” when prompted by the meter-programming device. Using the wand attached to the meter-programming device, read the bar code on the front of the power meter (see figure 1 for location). Pass the wand from left to right over the bar code. A successful read will result in a short beep sound being generated from the meter-programming device. After a successful bar code read (i.e. the meter-programming device beeped) the meter-programming device will prompt the operator to “program device with magnetic loop”. The magnetic loop is in the wand attached to the meterprogramming device also. Looking directly at the meter, and mentally superimposing the hands of a clock on the meter face for reference, place the meter-programming wand at the 3:00 position of the meter face, on the side of the plastic meter cover, touching the plastic meter cover with the wand. (See photograph below). Select “Program” on the meter-programming device display. The meterprogramming device will again beep when the meter has been programmed. Contact your supervisor for confirmation of meter operation. FCC INFORMATION: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient of relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet or circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this device not expressly approved by AMDS LLC could void the user’s authority to operate this equipment. Photograph showing bar code position and 3:00 position for programming wand placement on meter.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2004:08:13 18:11:19Z Modify Date : 2004:08:13 14:11:52-04:00 Page Count : 5 Creation Date : 2004:08:13 18:11:19Z Mod Date : 2004:08:13 14:11:52-04:00 Producer : Acrobat Distiller 5.0.5 (Windows) Author : Michael Proffitt Metadata Date : 2004:08:13 14:11:52-04:00 Creator : Michael Proffitt Title : Microsoft Word - 04-0166 User Guide Cover.docEXIF Metadata provided by EXIF.tools