Sensus Metering Systems WMIN01 AUTOMATIC WATER METER TRANSMITTER User Manual Installation Guide

Sensus Metering Systems AUTOMATIC WATER METER TRANSMITTER Installation Guide

UserManual.wiki >

Sensus Metering Systems >

WMIN01 User Manual

USERS MANUAL

WATER TRANSMITTER INSTALLATION GUIDE The following information contains installation instructions for the Transmitter Unit (MXU). The wiring connections are the same for both inside and pit set installations. Techniques may be different for the actual MXU placement in each type of installation. Recommended Tools and Materials • SR II ® security screw socket with 1/4" nut driver or ratchet wrench • 3M Scotchlok ® UY-2 butt connector “gel-caps” • 3M Scotchlok ® E-9Y stepped jaw crimping tool with wire cutter • Wire stripper tool • Screwdrivers (Phillips and standard blade heads) • Power drill and bit (1/4") • 8 x 1" sheet metal screws • 1/2" Electrical Metallic Tubing (EMT) • Conduit cutting tool • Hammer • Conduit driver • Three-conductor solid wire Wiring Diagram

WIRING INSTRUCTIONS The MXU wiring instructions assume the utility meter with an encoder register has been installed and the proper wire has been run to the MXU installation location. Three-conductor, 22 gauge, solid conductor cable is recommended. (For meter installation, refer to the installation information included in meter shipping cartons.) 1. Using the SR II security socket with ratchet wrench or nut driver, open the MXU enclosure by removing SR II type security screw. Bottom part of enclosure will contain the MXU battery and top part the electronics and connection wires. Connect the three wires from the encoder register to the matching color wires on the MXU. If not already done, strip approximately 2" off outer jacket of the encoder wire cable. The wire colors for each unit should be green, red, and black. Insert two matching color wire ends – red to red, green to green, and black to black into a UY-2 gel-cap with the color button of gel-cap facing away. (This provides a better view of wire positions inside the clear plastic gel-cap enabling the installer to see the wires are completely and properly inserted.) Using gel-cap pliers, squeeze the gel-cap. This will splice the two wires and release the waterproof gel to seal the connection. The splice can be checked by pulling gently on the gel-cap while holding the wires to be sure they are tight and secure. Repeat for the remaining two wire connections. If any of the wire connections are not being used they should be capped at the end with a gel-cap. This is to prevent water intrusion via wicking through the exposed wire ends. 2. Connect the battery to the MXU electronics. Using the gel-cap connecting technique described above, connect the red and white stripe wire from the battery to the red and white stripe wire from the MXU electronics. Repeat the procedure for the black and white stripe wire from the battery to the black and white stripe wire from the MXU. Caution: DO NOT cross connect the black and white and the red and white wires of the MXU and battery pack as this may cause damage to the MXU electronics. 3. (Optional) TouchRead ® Connection – The MXU includes a built-in TouchRead splitter connection to allow the encoder register to be interrogated by both the MXU and a remote TouchRead System sensor. Wall Mount TouchPad – Using two-conductor or three-conductor wire cable and gel-caps, connect wires to each of the green and white stripe wires from the MXU. Note: If three-conductor wire cable is used, the third wire is not utilized for the TouchRead Connection. At the TouchPad connection, connect the same two wires to the terminal screws on the back of the TouchPad. Caution: Be sure there is no bare wire-to-wire contact. (The TouchRead connection is non-polarity sensitive and will work as long as the same color wires are used at both ends of the connection. If three-conductor wire is used, be sure the third “dead” wire is not mistakenly connected at either end.) Pit-set Mount Sensor – The TouchRead pit-set sensor includes a factory-sealed three-conductor wire cable. Proper wire connections are therefore important. To activate the pit-set TouchRead sensor, use only the red and black wires from the sensor. Approximately 2" of the cable’s outer jacket must be stripped from its end to access these wires. Then, using gel-caps, connect the black wire from the sensor to one of the green and white stripe wires from the MXU. Next, connect the red wire from the sensor to the other green and white stripe wire from the MXU. 4. Verify MXU operation prior to final assembly - To verify MXU reading, use a Handheld Terminal (HHT) to interrogate the register and compare to the register odometer reading, register ID number, and MXU ID number. To verify TouchRead reading, use a TouchRead visual reader to display register odometer reading(s) and register ID number(s). If MXU does not function, check all wire connections, redo the connections or change battery pack. (For complete TouchRead installation and troubleshooting, see installation bulletins: TR-728, TR-997, and TR-998.) 5. After wiring connections are completed and MXU operation is verified, align guides of top and bottom parts of MXU and close, bringing the connection wires out the front side, using the wire pass-thru guides located on either side of the security screw. Secure the top and bottom parts of the MXU using the security screw. Caution: DO NOT over-tighten security screw.