Sensys Networks FLEX-RP FLEX RP Repeater User Manual

Sensys Networks, Inc. FLEX RP Repeater FLEX Repeater Data Sheet

a href="https://usermanual.wiki/Sensys-Networks" itemprop="url"> Sensys Networks >

User Manual

1608 4th Street Suite 200 Berkeley CA 94710| info@sensysnetworks.com | P 510.548.4620 F 510.548.8264 1608 4th Street Suite 200 Berkeley CA 94710 | info@sensysnetworks.com| P 510.548.4620 F 510.548.8264 Quick Start Guide: FLEX-RP-B/FLEX-RP-B-LLConnect BatteryUnlatch the two hinges. Open the repeater cover. Open repeater1aWarningsLithium Thionyl Chloride BatteriesSensys Networks uses Lithium Thionyl Chloride batteries in the following products:• SENSORS (VSN240-F, VSN240-T, VSN240-S, VSN240-M, VSN240-F-2, VSN240-T-2)• REPEATERS (RP240-B, RP240-B-LL, RP240-BH, RP240-BH-LL, FLEX-RP-B, FLEX-RP-B-LL)Lithium batteries are widely used in electronic products because they contain more energy per unit-weight than conventional batteries. However, the same properties that deliver high energy density also contribute to potential hazards if the batteries are damaged. Improper use or handling of the batteries may result in leakage or release of battery contents, explosion, or re.Following are the recommendations of the battery manufacturer for proper use and handling of batteries in the Sensys Networks devices mentioned above:• DO NOT CHARGE OR ATTEMPT TO RECHARGE THE BATTERIES (BATTERIES ARE NOT RECHARGEABLE)• DO NOT CRUSH OR PUNCTURE BATTERIES• DO NOT SHORT-CIRCUIT THE BATTERIES• DO NOT FORCE OVER-DISCHARGE OF THE BATTERIES• DO NOT INCINERATE OR EXPOSE BATTERIES TO EXCESSIVE HEATING• DO NOT EXPOSE BATTERY CONTENTS TO WATER• DO DISPOSE OF BATTERIES AND DEVICES CONTAINING BATTERIES IN ACCORDANCE WITH LOCAL REGULATIONSSensys Networks sensors contain no serviceable parts and should never be disassembled. Installation and removal of sensors from pavement should only be done by trained personnel and care should be taken to insure that the sensor casing is not punctured or crushed.Additional safety information is available from the battery’s manufacturer:Sensor battery cell: http://ultralifecorporation.com/download/308/Repeater battery cell: www.ewtbattery.com/en/DownView.asp?ID=9Connect battery cable to circuit-board connector (a). DO NOT PINCH OR STRESS CABLES. Wait approximately ve seconds for LED lights to blink. Close cover; ensure wires are not caught in edges. Latch the two hinges securely.Connect Battery
1608 4th Street Suite 200 Berkeley CA 94710| info@sensysnetworks.com | P 510.548.4620 F 510.548.8264 1608 4th Street Suite 200 Berkeley CA 94710 | info@sensysnetworks.com| P 510.548.4620 F 510.548.8264 Connect to Access PointSelect an access point from the automated list and click Connect. Note: Ensure the box for Load map data is checked before clicking Connect.Select IP addressClick the icon to start TrafcDOT2.Run TrafcDOT2The Main window displays. The map on the Main window populates and congured equipment appears on the map and in the sensor tray at the bottom of the window.Note: Before conguring or reconguring a repeater, ensure the correct repeater is displayed on the map by hovering over the repeater icon with the mouse to view repeater information.Main WindowQuick Start Guide: FLEX-RP-B/FLEX-RP-B-LL
Download:
Mirror Download [FCC.gov]
Document ID2399092
Application IDNqGwLFyJxQkKIXFkV3jUGQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize160.27kB (2003398 bits)
Date Submitted2014-09-24 00:00:00
Date Available2014-09-24 00:00:00
Creation Date2014-08-05 17:12:31
Producing SoftwareAdobe PDF Library 10.0.1
Document Lastmod2014-09-09 13:48:34
Document TitleFLEX Repeater Data Sheet
Document CreatorAdobe InDesign CS6 (Windows)
Document Author: Zenobia Redeaux
FCC ID Filing: TDB-FLEX-RP

Navigation menu