Sequel Technologies SLIMDWS Door/Window Sensor, Slimline User Manual CERTIFICATE OF COMPLIANCE

Download:
Mirror Download [FCC.gov]
Document ID	1151906
Application ID	CnfPKATqJlpMNTD58rEUiQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.35kB (404323 bits)
Date Submitted	2009-08-11 00:00:00
Date Available	2009-08-11 00:00:00
Creation Date	2009-08-10 06:20:53
Producing Software	Adobe PDF Library 9.0
Document Lastmod	2009-08-10 06:21:19
Document Title	CERTIFICATE OF COMPLIANCE
Document Creator	Acrobat PDFMaker 9.1 for Word
Document Author:	Systems Administrator

Rhein Tech Laboratories, Inc.
360 Herndon Parkway
Suite 1400
Herndon, VA 20170
http://www.rheintech.com
Ap p e n d ix G:
Ma n u a l
Please see the following pages.
Client:
Model:
Standard:
FCC ID:
Report #:
Sequel Technologies LLC
STWS-DWS-SLIM
FCC 15.231
V4X-SLIMDWS
2009214
Door/Window Sensor, Slim (STWS-DWS-SLIM)
Installation Instructions
Sequel Technologies, LLC
Document Number: 520-00019 Rev. A
General Description
Reed Switch
The Slim Line Door/Window Sensor (STWS-DWSSLIM) is a door/window sensor developed for use with
the ST security systems. The sensor achieves enhanced
wireless reliability using unique duplex narrow band
frequency diversity, which transmits and receives radio
signals on two separate frequencies.
Additional Information:
• Powered by two AAA alkaline batteries, which can
provide power for up to 5 years.
• Each transmitter has a unique factory-programmed
code that distinguishes itself to the receiver.
• Includes a built-in reed switch that closes if the
magnet is within 1/2” (12mm) of the sensor case.
Mounting hole
Magnet
1/2” Max.
AAA Batteries
Figure 2: DWS-SLIM Circuit Board
Installation
1. Select a sensor location. Avoid mounting the sensor
near the floor. For door mounts, mount the magnet
to the door and the sensor to the door frame.
2. Remove the sensor cover. Press the plastic tabs to
release the cover from the mounting base.
3. Mount the sensor base to the door or window frame.
Use included screws to affix the mounting base,
observing alignment marks shown in Fig 1.
4. Remove the magnet from its base by inserting a
small screw driver into the slot at the end of the
magnet cover. Push in and twist to remove the base.
5. Mount the magnet base within 1/2” of the sensor base.
6. Snap the sensor and magnet onto their mounting
bases. If the sensor has not been enrolled, proceed
to the programming procedure before mounting the
sensor on the base.
Note: It is undesirable to mount the sensor or magnet on a metal surface.
If mounting on metal is unavoidable, use spacers (available from Sequel
Technologies) to reduce transmission problems.
Case Locking Tab (one on each end)
Figure 1: Mounting Base
Programming
To enroll a DWS into system memory:
1. Enter program mode (NEXT + NEXT + NEXT +
 + Installer PIN)
2. The keypad will display “Devices Available.” Select
. The display shows “Auto Enroll On.”
3. To enroll the sensor, remove the circuit board from
the cover, insert batteries in sensor and trip the sensor
(move the magnet away from the reed switch)*.
4. Upon enrollment, the keypad emits one beep and
the display shows the zone number and sensor ID.
Replace the sensor on the mounting base.
5. Continue enrolling additional sensors if desired. When
finished, press  to exit.
* The sensor will only enroll within the first 3 “routine” (reed switch) trips after
power up. If the sensor has already tripped 3 or more times, remove the
batteries, reinstall the batteries, and trip the sensor to enroll.
Testing
The system contains a walk test mode that allows you to
activate any zone/sensor and verify its correct operation
without causing an alarm. An audible tone will occur
with each tested sensor in walk test, with a display to
provide additional feedback.
To initiate a walk test:
1. Press NEXT + NEXT and the keypad will display
LOG TEST RESET.
2. Select  and enter the installer or user PIN.
The display will show WALK COMM.
3. Select  and the keypad will display “Walk
Test Active.”
4. Trip each zone/sensor one at a time and the system
responds with a tone from the keypad.
5. As each tested sensor is added to a scrolling list of tested
sensors, the signal strength will be shown on the LCD
display. A higher value indicates a stronger signal level.
6. Exit walk test mode by pressing .
Specifications
• Compatibility: All Sequel Technologies ST Security
Systems (ST8 requires Expansion Transceiver Module)
• Power: Two AAA alkaline batteries (average battery
life is 3-5 years)
• Transmitting Frequency: 319.5 MHz and 345 MHz
• Supervision Interval: 60 minutes
• Transmit Range: 500 feet, open air
• Sensor Dimensions: 4.21” x .87” x .65” (LxWxD)
• Magnet Dimensions: 1.86” x .41” x .47” (LxWxD)
• Material: High-impact ABS
• Operating Temperature: -30° to 120°F (-34° to 49°C)
• Max. Humidity: 90% relative humidity, non condensing
• Regulatory Approvals: FCC 15, UL (Pending)
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes and/or modifications not approved by Sequel Technologies, LLC could void the user’s
authority to operate the equipment.
FCC ID: V4X-SLIMDWS
Troubleshooting
Problem
Action
• Bring the wireless sensors closer to the
The panel does
EXT and retest. If signals are properly
not respond to
received, the issue may be related to
wireless sensors.
environmental noise or interference.
There are no
•
Distance from the receiver and/or
alarm, chime,
installation environment will affect
or walk test
the sensor signal strength. Reposition
responses.
the sensor and/or EXT if necessary.
The system
indicates a
sensor low
battery.
• Replace the sensor’s battery. Test the
sensor after replacing the battery. Testing
the device allows the system to receive a
signal with the new battery information.
The system
• Check the distance between the
constantly
magnet and reed switch and verify that
indicates that the
the distance is not more than 1/2”.
sensor is open.
Sequel Technologies
2958 Cleveland Ave. N
Roseville, MN 55113 USA
Copyright © 2009 Sequel Technologies, LLC.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Systems Administrator
Create Date                     : 2009:08:10 06:20:53-07:00
Modify Date                     : 2009:08:10 06:21:19-07:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2009:08:10 06:21:19-07:00
Creator Tool                    : Acrobat PDFMaker 9.1 for Word
Format                          : application/pdf
Title                           : CERTIFICATE OF COMPLIANCE
Creator                         : Systems Administrator
Document ID                     : uuid:d6f936a5-83ea-4c50-af14-95c26042837c
Instance ID                     : uuid:1228f266-c2c4-4b99-9a39-886c9686c8ab
Producer                        : Adobe PDF Library 9.0
Page Count                      : 3

EXIF Metadata provided by EXIF.tools