Sercomm LC4R LTE module User Manual

Sercomm Corporation LTE module

User Manual

Ver 1.6 CONFIDENTIAL Ninja LTE mini PCIe Module LC4R User Guide Version 1.6 This document contains information of a proprietary nature. ALL INFORMATION CONTAINED HEREIN SHALL BE KEPT IN STRICT CONFIDENTIAL. None of this information shall be divulged to persons other than SerComm employees authorized by the nature of their duties to receive information, or individuals and organizations authorized by SerComm in accordance with existing policy regarding release of company information. SerComm Corp. 8F, No. 3-1, YuanQu St., Nan-Kang Taipei 115, Taiwan, R.O.C.
CONFIDENTIAL 2 Change List Revision Date Author Change descriptions 1.0 2015/10/14 Alex Tu Initial release 1.1 2015/10/14 Alex Tu Add CDD ON/OFF 1.2 2015/10/21 Alex Tu Add NAS enable Firmware upgrade 1.3 2015/10/23 Alex Tu Replace 0,0,0 with null after APNNAME in AT+CGDCONT command 1.4 2015/11/23 Alex Tu Add more AT commands 1.5 2016/4/1 Alex Tu Upgrade content update 1.6 2016/6/6 Alex Tu Add FCC statement
CONFIDENTIAL 3 Table of Contents Change List ................................................................................................................................................................................... 2Table of Contents .......................................................................................................................................................................... 31 Product Overview ....................................................................................................................................................................... 71.1 Introduction ......................................................................................................................................................................... 71.2 System Structure ................................................................................................................................................................ 71.3 Network structure ................................................................................................................................................................ 81.4 Federal Communication Commission Interference Statement ......................................................................................... 10Radiation Exposure Statement: .................................................................................................................................................. 102 DM mode.................................................................................................................................................................................. 122.1 Read Band Scan List ........................................................................................................................................................ 122.2 Write Band Scan List ........................................................................................................................................................ 122.3 Update Non-Volatile .......................................................................................................................................................... 122.4 Configure PCI Black List ................................................................................................................................................... 122.5 Show PCI Black List .......................................................................................................................................................... 133 UCFG commands .................................................................................................................................................................... 143.1 Connection Manager Selection ......................................................................................................................................... 143.2 PLMN Search Type ........................................................................................................................................................... 143.3 Set AutoCM Mode ............................................................................................................................................................. 143.4 Set ATCM Mode ............................................................................................................................................................... 153.5 USB Ethernet Interface Enable ......................................................................................................................................... 153.6 USB Ethernet Interface Disable ........................................................................................................................................ 153.7 USB Ethernet Interface Mode ........................................................................................................................................... 153.8 List of PLMN Search Type ................................................................................................................................................ 154 AT Commands ......................................................................................................................................................................... 164.1 Request information commands ....................................................................................................................................... 164.1.1 AT+CGMIRequest manufacture identification ........................................................................................................... 164.1.2 AT+CGMM Request model identification ............................................................................................................... 164.1.3 AT+CGMRRequest revision identification ................................................................................................................. 164.1.4 AT+CGSNRequest product serial number identification ........................................................................................... 164.1.5 AT+CSCSRequest TE character set ......................................................................................................................... 164.1.6 AT+CIMIRequest international mobile subscriber identity ........................................................................................ 174.2 Network service related commands .................................................................................................................................. 184.2.1 AT+COPSPLMN selection ........................................................................................................................................ 18
CONFIDENTIAL 4 4.2.2 AT+CLCKFacility lock ................................................................................................................................................ 184.2.1 AT+CPWDChange password .................................................................................................................................... 194.2.2 AT+CPOLPreferred PLMN list ................................................................................................................................... 194.2.3 AT+CPLSSelection of preferred PLMN list ............................................................................................................... 214.3 Mobile Termination control and status commands ........................................................................................................... 214.3.1 AT+CPASPhone activity status ................................................................................................................................. 214.3.2 AT+CFUNSet phone functionality ............................................................................................................................. 224.3.3 AT+CPINEnter PIN .................................................................................................................................................... 224.3.4 AT+CPUKUnblock PIN2 ............................................................................................................................................ 234.3.5 AT+CSQSignal Quality .............................................................................................................................................. 234.3.6 AT+CCLKClock ......................................................................................................................................................... 244.3.7 AT+CSIMGeneric SIM access ................................................................................................................................... 244.3.8 AT+CRSMRestricted SIM access ............................................................................................................................. 254.3.9 AT+CLACList all available AT commands ................................................................................................................ 264.3.10 AT+CPINCPIN remaining attempt number ............................................................................................................. 264.3.11 AT+CPINRRemaining PIN retries ........................................................................................................................... 274.4 Commands for packet Domain ......................................................................................................................................... 274.4.1 AT+CGDCONTDefine PDP (Packet Data Protocol) Context .................................................................................... 274.4.2 AT+CGDSCONTDefine Secondary PDP Context ..................................................................................................... 294.4.3 AT+CGTFT Traffic Flow Template ............................................................................................................................ 304.4.4 AT+CGATTPS attach or detach ................................................................................................................................ 324.4.5 AT+CGACT PDP Context Activate or Deactivate ..................................................................................................... 334.4.6 AT+CGCMOD PDP Context Modify .............................................................................................................................. 334.4.7 AT+CGDATA Enter data rate .................................................................................................................................... 334.4.8 AT+CGPADDRShow PDP (IP) address .................................................................................................................... 344.4.9 AT+CGEREPPacket Domain event reporting ........................................................................................................... 344.4.10 AT+CEREG EPS network registration status .......................................................................................................... 354.4.11 AT+CGCONTRDP PDP Context Read Dynamic Parameters ................................................................................ 364.4.12 AT+CGSCONTRDP Secondary PDP Context Read Dynamic Parameters............................................................ 374.4.13 AT+CGTFTRDPTraffic Flow Template Read Dynamic parameters ....................................................................... 374.4.14 AT+CGEQOSDefine EPS Quality of Service .......................................................................................................... 394.4.15 AT+CGEQOSRDP EPS Quality of Service Read Dynamic Parameters .................................................................... 404.5 SMS Commands ............................................................................................................................................................... 414.5.1 AT+CSMS ...................................................................................................................................................................... 414.5.2 AT+CPMS ...................................................................................................................................................................... 414.5.3 AT+CMGF ...................................................................................................................................................................... 414.5.4 AT+CSCA ...................................................................................................................................................................... 414.5.5 AT+CSMP ...................................................................................................................................................................... 42
CONFIDENTIAL 5 4.5.6 AT+CMGL ...................................................................................................................................................................... 424.5.7 AT+CMGR ..................................................................................................................................................................... 444.5.8 AT+CMGS ...................................................................................................................................................................... 444.5.9 AT+CMSS ...................................................................................................................................................................... 454.5.10 AT+CMGW ................................................................................................................................................................... 454.5.11 AT+CMGD ................................................................................................................................................................... 454.5.12 AT+CMGC ................................................................................................................................................................... 465 Other commands ..................................................................................................................................................................... 475.1 CDD .................................................................................................................................................................................. 475.1.1 CDD ON (2 Tx) .............................................................................................................................................................. 475.1.2 CDD OFF (1 Tx) ............................................................................................................................................................. 475.2 Q Log Message ................................................................................................................................................................. 485.2.1 PERF: CPU Usage Profile ............................................................................................................................................. 485.2.2 FRAME: LTE Radio Frame Information ......................................................................................................................... 495.2.3 RF: RF Metric ................................................................................................................................................................. 495.2.4 CHAN: Channel Information .......................................................................................................................................... 505.2.5 MEAS: Measurement Result of a Serving Cell .............................................................................................................. 515.2.6 NMEAS: Measurement Result of a Neighbor Cell ......................................................................................................... 525.2.7 L1D: PHY DL statistics ................................................................................................................................................... 525.2.8 L1U: PHY UL Statistics .................................................................................................................................................. 555.2.9 MCS: DL/UL MCS statistics ........................................................................................................................................... 565.2.10 CSI: Channel State Information ................................................................................................................................... 575.2.11 TP: Throughput Statistics ............................................................................................................................................ 585.2.12 MAC ............................................................................................................................................................................. 585.2.13 RLC .............................................................................................................................................................................. 585.2.14 DP: Data-path statistics ............................................................................................................................................... 595.2.15 CIP: Cipher Integrity Statistics ..................................................................................................................................... 595.3 NAS Protocol Binary Decode ............................................................................................................................................ 605.3.1 Install decoder ................................................................................................................................................................ 605.3.2 Copy NAS Data .............................................................................................................................................................. 605.3.3 Paste to Decoder ........................................................................................................................................................... 606 Network Connection Examples ................................................................................................................................................ 616.1 Auto connection (Three bands) ........................................................................................................................................ 616.2 Auto connection (One band, B41 for example) ................................................................................................................ 616.3 Manual Connection (Three bands) ................................................................................................................................... 616.4 Manual Connection (One band only) ................................................................................................................................ 626.5 Disconnect ........................................................................................................................................................................ 62
CONFIDENTIAL 6 6.6 Get IP Address .................................................................................................................................................................. 627 FW Upgrade ............................................................................................................................................................................. 637.1 Using JIG board or CPE board ......................................................................................................................................... 63
CONFIDENTIAL 7 1 Product Overview 1.1 Introduction LC4R module uses GCT GDM7243Q chipset which is a wireless LTE FDD/TDD solution. The chipset inside the module owns a dual core CPU. One of CPU (ARM1) is designed to run LTE modem job; the other CPU (ARM0) is designed for router or other application. In order to get full control, GCT designs three kinds of command sets.  AT commands : 3GPP standard compatible commands to control network connection  DM commands : GCT proprietary commands for calibration and NVM configuration  UCFG commands : GCT proprietary application that manages LTE NVM (Non-Volatile Memory) block used as command based interface at GDM7243 Linux kernel environment. We will use them for different purposes. 1.2 System Structure Figure 1: Device Application for CPE From above diagram, there is an UCM (Unify Connection Manager) application running in ARM0 for connnection function. To simply dial process, using it is good suggestion, and AT commands are required. If more specific dial requirement required, DM/UCFG commands are needed.
CONFIDENTIAL 8 1.3 Network structure GDM7243M network block diagram LC4R chipset, GDM7243Q, doesn’t have WiMAX function. MII ETH is not used either due to mini PCIe form factor, so usb0 is the only interface for network communication. When NAT is enabled, notebook/PC will get IP from DHCP server on br0 interface, it will be like 192.168.0.10. br0 IP is 192.168.0.1. ltepdn0 IP can be retrieved by AT command or DM command Host Interface. LC4R uses USB 2.0 for data communication. USB interface need to be enabled and usb mode need to be configured for different condition.  Connect to test board and Windows PC Auto or RNDIS mode  Connect to Linux OS CDC-EEM or CDC-ECM mode ACM port is a virtual port on USB for AT command access only. We suggested using this interface for AT command because there is no console dump data which mixes with AT command response. Device can be found at /dev/ttyACM0.
CONFIDENTIAL 9 Modem control and monitor are done by UART which is defined in reserved pin 17 & 19 of mini PCIe interface. UART0_TXD and UART0_RXD voltage is 1.8V. Default baud rate is 921600/n/8/1. If CPE board baud rate cannot support such high bit rate, reducing baud rate is doable from UART at boot loader mode or by pre-configuration. To update UART port baudrate, go to boot loader (reboot and press enter key during booting), and follow the commands to update new value. Reboot is still required to take new baudrate working.
CONFIDENTIAL 10 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution:  Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and the maximum antenna gain allowed for use with this device is 4 dBi for B25/B41 and 1 dBi for B26. 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: P27LC4R”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User 1.4 Federal Communication Commission Interference Statement
CONFIDENTIAL 11 The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
CONFIDENTIAL 12 2 DM mode When system boots up, ”DM>” prompt will be seen, then DM mode is active. Some of commands will be introduced in the following section. 2.1 Read Band Scan List Command Response nv bcfgr <cmd=49> <port=0> 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 OK Example: nv bcfgr 49 0 2.2 Write Band Scan List Command Response nv bcfgw <cmd=49> <port=0> <band=41 25 26> OKExample: nv bcfgw 49 0 41 25 26 2.3 Update Non-Volatile Command Response nv bcfgsv <cmd=1> OK Example: nv bcfgsv 1 2.4 Configure PCI Black List This command sets cell black list. Command Response rrc dm cell block [[<earfcn> <pci>]] rrc dm cell block < 'a' or 'd'> [[<earfcn> <start pci> <end pci>]] 'a' : add a cell to the list 'd' : delete a cell from the list start pci : low PCI of the range end pci : high PCI of the range Notice: total 48 records Example: rrc dm cell block a 39650 0 100 rrc dm cell block d 39650 0 100
CONFIDENTIAL 13 2.5 Show PCI Black List Command Response rrc dm cell block ? Cell Black List : 2 (use SIB9:0) >> earfcn: 39950, pci: 0 ~ 100 >> earfcn: 38950, pci: 0 ~ 100
CONFIDENTIAL 14 3 UCFG commands UCFG application needs to be run at Linux kernel. To go to Linux shell, type shell from DM>, Type “exit” to return DM> mode from Llinux shell mode 3.1 Connection Manager Selection Command Response ucfg set config wan lte vendor <value> vendor=<value> <value> : 0 None 1 lteautocm 3.2 PLMN Search Type Command Response ucfg set config wan lte plmn_search_type <value> vendor=<value> <value> : 0 PLMN Search 1 PLMN Search with band 2 PLMN Extension Search 3.3 Set AutoCM Mode To set lteautocm operation mode. If manual connection is designed, manual mode of lteaucm is used Command Response ucfg set config wan lte autocm manual <value> vendor=<value> <value> : 0 Auto 1 Manual
CONFIDENTIAL 15 3.4 Set ATCM Mode To set atcm mode about PDN connect Command Response ucfg set config wan lte atcm use_autocm_req <value> vendor=<value> <value> : 0 By itself 1 Request to lteautocm 3.5 USB Ethernet Interface Enable Command Response ucfg set config lan usbeth ENABLE 1 ENABLE=1 3.6 USB Ethernet Interface Disable Command Response ucfg set config lan usbeth ENABLE 0 ENABLE=0 3.7 USB Ethernet Interface Mode Command Response ucfg set config lan usbeth mode <value> mode=<value> <value> : 0 Auto Detect (Default) 1 RNDIS 2 CDC-EEM 3 CDC-ECM 3.8 List of PLMN Search Type Command Response ucfg set plmn search_list <[type]/[number]/[value]... [type]/[number]/[value]> mode=0 [type] : the type of PLMN Search 1 MRU Search 2 Earfcn Search 3 Band Search 4 Sarfcn Range Search [number] : the count of each PLMN Search type, Max of number is 5 While type=1, means The count of MRU Search While type=2, means The number of earfcn While type=3, means The number of Band While type=4, means The number of Earfcn range [value] : value of each PLMN Search type 1 N/A 2 /earfcn_1/earfcn_2/...../earfcn_[number] 3 /band_1/band_2..../band_[number] 4 /start_earfcn_1/end_earfcn1/...../start_earfcn_[number]/end_earfcn_[number]
CONFIDENTIAL 16 4 AT Commands AT commands can be accessed from UART port and ACM port. 4.1 Request information commands 4.1.1 AT+CGMI Request manufacture identification This command gets the manufacture identification Command Response Value +CGMI <manufacture> +CME ERROR: <err> GCT +CGMI=? 4.1.2 AT+CGMM Request model identification This command gets the model identification Command Response Value +CGMM <model> +CME ERROR: <err> GDM7243R0 +CGMM=? - <model>: The value will be updated to GDM7243Q in next FW release. 4.1.3 AT+CGMR Request revision identification This command gets the revision identification Command Response Value +CGMR <revision> +CME ERROR: <err> FW_VER: 0.2.65.1 +CGMR=? 4.1.4 AT+CGSN Request product serial number identification This command gets the serial number identification Command Response Value +CGSN <sn> IMEI 4.1.5 AT+CSCS Request TE character set Command Response Value +CSCS=[<chset>] +CSCS? +CSCS:<chset> +CSCS=? +CSCS: (list of supported <chset>s)
CONFIDENTIAL 17 4.1.6 AT+CIMI Request international mobile subscriber identity Command Response Value +CIMI <IMSI> +CME ERROR: <err> +CIMI=? - <IMSI>: Interational Mobile Subscriber Identity (string without double quote)
CONFIDENTIAL 18 4.2 Network service related commands 4.2.1 AT+COPS PLMN selection Forces an attemp to select and register the GSM/UMTS network operator Command Possible Response+COPS=? +COPS: ([list of supported<stat> ,long alphanumeric <oper> ,short alphanumeric <oper> ,numeric <oper>[,<Act>] )s][,,(list of supported<mode> s),(list of supported <format> s)] +CME ERROR:<err> +COPS? +COPS: <mode>[,<format>,<oper>[,<Act>]] +COPS=[<mode>[,format>[,<oper>]]] - <stat>: Availability of operator  0 unknown  1 available  2 current  3 forbidden - <oper>: Shows the operator identity in the format set by <format> - <mode>: Registration mode  0 automatic (<oper> field is ignored)  1 manual (<oper> field shall be present, and <AcT> optionally)  2 deregister from network  3 set only <format> (for read command AT+COPS?), do not attempt registration / de-registration (<oper> field is ignored); this value is not applicable in read command response  4 manual/automatic (<oper> field shall be present); if manual selection fails, automatic mode<mode> =0) is entered  5 manual (use plmn extension list) - <format>: Format of <oper> reports  0 long format alphanumeric <oper>  1 short format alphanumeric <oper>  2 numeric <oper> 4.2.2 AT+CLCK Facility lock
CONFIDENTIAL 19 4.2.1 AT+CPWD Change password 4.2.2 AT+CPOL Preferred PLMN list
CONFIDENTIAL 20
CONFIDENTIAL 21 4.2.3 AT+CPLS Selection of preferred PLMN list 4.3 Mobile Termination control and status commands 4.3.1 AT+CPAS Phone activity status
CONFIDENTIAL 22 4.3.2 AT+CFUN Set phone functionality 4.3.3 AT+CPIN Enter PIN
CONFIDENTIAL 23 4.3.4 AT+CPUK Unblock PIN2 4.3.5 AT+CSQ Signal Quality
CONFIDENTIAL 24 4.3.6 AT+CCLK Clock 4.3.7 AT+CSIM Generic SIM access
CONFIDENTIAL 25 4.3.8 AT+CRSM Restricted SIM access
CONFIDENTIAL 26 4.3.9 AT+CLAC List all available AT commands 4.3.10 AT+CPINC PIN remaining attempt number
CONFIDENTIAL 27 4.3.11 AT+CPINR Remaining PIN retries 4.4 Commands for packet Domain 4.4.1 AT+CGDCONT Define PDP (Packet Data Protocol) Context Specifies PDP context parameter values for a PDP context identified by the (local) context identification parameter, <cid>. - [set command] : specifies PDP context parameter values for a PDP context identified by the (local) context identification parameter, <cid>. : a special form of the set command, +CGDCONT=<cid> causes the values for context number <cid> to become undefined. - [read command] : returns the current settings for each defined context. - [test command] : returns values supported as a compound value. Command Response +CGDCONT=[<cid>[,<PDP_type>[,<APN>[, <PD P_addr>[,<d_comp>[,<h_comp>[,<IPv4Addr A lloc>[,<emergency indication>[,<PCSCF_ discovery>[,<IM_CN_Signalling_Flag _Ind>]]]]]]]]]] OK ERROR +CGDCONT? +CGDCONT: <cid>,<PDP_type>,<APN>,<PDP_ad dr>,<d_comp>,<h_comp>[,<IPv4AddrAlloc>[,<emerg
CONFIDENTIAL 28 ency indication>[,<PCSCF_ discovery>[,<IM_CN_Signalling_Flag_ Ind>]]]][<CR><LF>+CGDCONT: <cid>,<PDP_type>,<APN>,<PDP_addr>,<d_comp>, <h_comp>[,<IPv4Add rAlloc>[,<emergency indication>[,<PCSCF_ discovery>[,<IM_CN_Signalling_Flag_ Ind>]]]][...]]+CGDCONT=? +CGDCONT: (range of supported <cid>s),<PDP_type>,,,(list of supported <d_comp>s),(list of supported <h_comp>s),(list of supported <IPv4AddrAlloc>s),(list of supported <emergency indication>s),(list of supported <PCSCF_ discovery>s),(list of supported <IM_CN_Signalling_Flag_Ind>s) [<CR><LF>+CGDCONT: (range of supported <cid>s),<PDP_type>,,,(list of supported <d_comp>s),(list of supported <h_comp>s),(list of supported <IPv4AddrAlloc>s),(list of supported <emergency indication>s),(list of supported <PCSCF_ discovery>s),(list of supported <IM_CN_Signalling_Flag_Ind>s) [...]] - <cid>: numeric; specifies a particular PDP context definition. - <PDP_type>: string; specifies the type of packet data protocol X.25 : ITU-T/CCITT X.25 layer 3 (Obsolete) IP : Internet Protocol IPV6 : Internet Protocol, version 6 IPV4V6 : Virtual <PDP_type> introduced to handle dual IP stack UE capability. OSPIH : Internet Hosted Octect Stream Protocol (Obsolete) PPP : Point to Point Protocol (IETF STD 51) - <APN>: string; a logical name that is used to select the GGSN or the external packet data network - <PDP_addr> for EPS, this field is omitted. - <d_comp>: numeric; controls PDP data compression. 0 - off (default if value is omitted) 1 - on (manufacturer preferred compression) 2 - V.42bis 3 - V.44 Other values are reserved. - <h_comp>: numeric; controls PDP header compression. 0 - off (default if value is omitted) 1 – on (manufacturer preferred compression) 2 - RFC1144 (applicable for SNDCP only) 3 - RFC2507 4 - RFC3095 (applicable for PDCP only) Other values are reserved. - <IPv4AddrAlloc>: numeric; controls how the MT/TA requests to get the IPv4 address information 0 - IPv4 Address Allocation through NAS Signaling (default if omitted) 1 - IPv4 Address Allocated through DHCP - <emergency indication>: a numeric parameter used to indicate whether the PDP context is for emergency bearer services or not. 0 PDP context is not for emergency bearer services - <P-CSCF_discovery>: a numeric parameter influences how the MT/TA requests to get the P-CSCF address, see 3GPP TS 24.229 [89] annex B and annex L. 0 Preference of P-CSCF address discovery not influenced by +CGDCONT 1 Preference of P-CSCF address discovery through NAS Signalling
CONFIDENTIAL 29 2 Preference of P-CSCF address discovery through DHCP - <IM_CN_Signalling_Flag_Ind>: a numeric parameter used to indicate to the network whether the PDP context is for IM CN subsystem-related signalling only or not. 0 UE indicates that the PDP context is not for IM CN subsystem-related signalling only 4.4.2 AT+CGDSCONT Define Secondary PDP Context
CONFIDENTIAL 30 4.4.3 AT+CGTFT Traffic Flow Template
CONFIDENTIAL 31
CONFIDENTIAL 32 4.4.4 AT+CGATT PS attach or detach
CONFIDENTIAL 33 4.4.5 AT+CGACT PDP Context Activate or Deactivate Activate or deactivate the specified PDP context(s). - [execution command] : activate or deactivate the specified PDP context(s). <cid>: is a numeric parameter which specifies a particular PDP context definition. - [read command] : returns the current Packet Domain service state. - [test command] : requests information on the supported PDP context activation states Command Response +CGACT=<state>,<cid> OK ERROR+CGACT? +CGACT: <cid>, <state> [<CR><LF>+CGACT: <cid>, <state>[…]] +CGACT=? +CGACT: (list of supported <state>s) - <state>: indicates the state of PS attachment 0 – deactivated 1 – activated other values are reserved and will result in an ERROR response to the execution command - <cid>: numeric; specifies a particular PDP context definition. 4.4.6 AT+CGCMOD PDP Context Modify 4.4.7 AT+CGDATA Enter data rate
CONFIDENTIAL 34 4.4.8 AT+CGPADDR Show PDP (IP) address 4.4.9 AT+CGEREP Packet Domain event reporting
CONFIDENTIAL 35 4.4.10 AT+CEREG EPS network registration status Reports changes in network registration - [set command] : controls the presentation of an unsolicited result code when there is a change in the MT's EPS network registration status. - [read command] : returns the status of result code presentation and an integer <stat> which shows whether the network has currently indicated the registration of the MT - [test command] : list of supported <n>s Command Response +CEREG=<n> OK ERROR+CEREG? +CEREG: <n>,<stat>[,<lac>,<rac>,<ci>[,<AcT>]] +CME ERROR: <err> +CEREG=? +CEREG: (list of supported <n>s) -<n>: numeric;  0 disable network registration unsolicited result code  1 enable network registration unsolicited result code +CEREG: <stat>  2 enable network registration and location information unsolicited result code +CEREG: <stat>[,<lac>,<rac>,<ci>[,<AcT>]] -<stat>: numeric; EPS registration status  0 not registered, MT is not currently searching an operator to register to  1 registered, home network  2 not registered, but MT is currently trying to attach or searching an operator to register to  3 registration denied  4 unknown  5 registered, roaming -<lac>: string; two byte location area code or tracking area code in hexadecimal format (e.g. "00C3" equals 195 in decimal). -<rac>: string; one byte routing area code in hexadecimal format (e.g. "1C" equals 28 in decimal). If no routing area code is applicable, "00" (equals 00 in decimal) is provided. -<ci>: string; four byte GERAN/UTRAN/E-UTRAN cell ID in hexadecimal format. -<AcT>: numeric; access technology of the registered network
CONFIDENTIAL 36  0 GSM  1 GSM Compact  2 UTRAN  3 GSM w/EGPRS  4 UTRAN w/HSDPA  5 UTRAN w/HSUPA  6 UTRAN w/HSDPA and HSUPA  7 E-UTRAN 4.4.11 AT+CGCONTRDP PDP Context Read Dynamic Parameters - [execution command] : returns the relevant information <bearer_id>, <apn>, <ip_addr>, <subnet_mask>, <gw_addr>, <DNS_prim_addr>, <DNS_sec_addr>, <P-CSCF_prim_addr> and <PCSCF_sec_addr> for a non secondary PDP Context established by the network with the primary context identifier <p_cid> : If the parameter <p_cid> is omitted, the relevant information for all established PDP contexts are returned - [test command] : returns a list of <p_cid>s associated with active contexts Command Response +CGCONTRDP=[<p_cid>] +CGCONTRDP: <p_cid>, <bearer_id>, <apn>[, <ip_addr>, <subnet_mask>[, <gw_addr>[, <DNS_prim_addr>[, <DNS_sec_addr>[, <PCSCF_ prim_addr>[, <P-CSCF_sec_addr>]]]]]] [<CR><LF>+CGCONTRDP: <p_cid>, <bearer_id>, <apn>[, <ip_addr>, <subnet_mask>[, <gw_addr>[, <DNS_prim_addr>[, <DNS_sec_addr>[, <PCSCF_ prim_addr>[, <P-CSCF_sec_addr>]]]]]] […]]+CGCONTRDP=? +CGCONTRDP: (list of <p_cid>s associated - <p_cid>: numeric; specifies a particular non secondary PDP context definition. The parameter is local to the TE-MT interface and is used in other PDP context-related commands. - <bearer_id>: numeric; identifies the bearer, EPS Bearer in EPS and NSAPI in UMTS/GPRS. - <APN>: string; a logical name that was used to select the GGSN or the external packet data network. - <ip_addr>: string; shows the IP Address of the MT. The string is given as dot-separated numeric (0-255) parameters on the form: "a1.a2.a3.a4" for IPv4 or "a1.a2.a3.a4.a5.a6.a7.a8", for IPv6. If the MT has dual stack capabilities the string shows first the dot separated IPv4 Address followed by the dot separated IPv6 Global Prefix Address. The IPv4 address and the IPv6 address parameters are separated by space: "a1.a2.a3.a4 a1:a2:a3:a4:a5:a6:a7:a8" - <subnet_mask>: string; shows the subnet mask for the IP Address of the MT. The string is given as dot-separated numeric (0-255) parameters. If the MT has dual stack capabilities the string shows the dot separated IPV4 subnet mask followed by the dot separated IPV6 subnet mask. The subnet masks are separated by space. - <gw_addr>: string; shows the Gateway Address of the MT. The string is given as dot-separated numeric (0-255) parameters If the MT has dual stack capabilities the parameter shows first the dot separated IPV4 Gateway address followed by the dot separated IPV6 Gateway Address. The gateway addresses are separated by space.
CONFIDENTIAL 37 - <DNS_prim_addr>: string; shows the IP Address of the primary DNS Server. If the MT has dual stack capabilities the parameter shows first the dot separated IPV4 Address, followed by the dot separated IPV6 Address of DNS Server. - <DNS_sec_addr>: string; shows the IP address of the secondary DNS Server. If the MT has dual stack capabilities the parameter shows first the dot separated IPV4 Address, followed by the dot separated IPV6 Address of DNS Server. - <P_CSCF_prim_addr>: string; shows the IP Address of the primary P-CSCF Server. If the MT has dual stack capabilities the parameter shows first the dot separated IPV4 Address, followed by the dot separated IPV6 primary Address of P-CSCF Server. - <P_CSCF_sec_addr>: string; shows the IP Address of the secondary P-CSCF Server. If the MT has dual stack capabilities the parameter shows first the dot separated IPV4 Address, followed by the dot separated IPV6 Address of P-CSCF Server. 4.4.12 AT+CGSCONTRDP Secondary PDP Context Read Dynamic Parameters 4.4.13 AT+CGTFTRDP Traffic Flow Template Read Dynamic parameters
CONFIDENTIAL 38
CONFIDENTIAL 39 4.4.14 AT+CGEQOS Define EPS Quality of Service
CONFIDENTIAL 40 4.4.15 AT+CGEQOSRDP EPS Quality of Service Read Dynamic Parameters
CONFIDENTIAL 41 4.5 SMS Commands 4.5.1 AT+CSMS 4.5.2 AT+CPMS 4.5.3 AT+CMGF 4.5.4 AT+CSCA
CONFIDENTIAL 42 4.5.5 AT+CSMP 4.5.6 AT+CMGL
CONFIDENTIAL 43
CONFIDENTIAL 44 4.5.7 AT+CMGR 4.5.8 AT+CMGS
CONFIDENTIAL 45 4.5.9 AT+CMSS 4.5.10 AT+CMGW 4.5.11 AT+CMGD
CONFIDENTIAL 46 4.5.12 AT+CMGC
CONFIDENTIAL 47 5 Other commands 5.1 CDD 5.1.1 CDD ON (2 Tx) 1. Run the command in shell mode, mount -o remount,rw / 2.Edit script file, vi etc/sysconfig/script/lte_init_script.sh 3.Update mode, chmod +x /etc/sysconfig/script/lte_init_script.sh 4. write "l1u t cdd 1 4" , save file, and reboot 5.1.2 CDD OFF (1 Tx) Update etc/sysconfig/script/lte_init_script.sh with "l1u t cdd 0 4" and save file, reboot.
CONFIDENTIAL 48 5.2 Q Log Message There are three text-DM modes when q log command uses, DM>q 0/1/2.  Interactive mode (q 0) Logging is disabled but command line interface is enabled.  Logging mode (q 1) Logging is enabled but command line interface is disabled.  Verbose mode (q 2) Both logging and CLI are enabled. To enable NAS protocol dump, type DM>dbg nas* -1 before q log command. 5.2.1 PERF: CPU Usage Profile Example: PERF : C(88.4/0.9/7.4/3.3) I(4101) M(H:10.0/2MB P:0.4/0.5/0.1/0.1/2MB)
CONFIDENTIAL 49 5.2.2 FRAME: LTE Radio Frame Information Example: FRAME: CONNECTED CAT5 TDD(2:7,N) Pos=(38245,38247,38247,38247) STI=836 5.2.3 RF: RF Metric
CONFIDENTIAL 50 Example: RF : E(39850,39850) B41 F25160 AFC(R,0:-182:34,-160,H,0x409) AGC(N,0x53:50:55,0x5f:5a:61,0x60:5d:61,0x6b:66:6d) ACI=0 5.2.4 CHAN: Channel Information
CONFIDENTIAL 51 Example: CHAN : 20MHz #A2 TM2 PCI=501 DS(S,96,0,0,0/0.3,0.3) ACE(I) FIB(-1:0:0:-1) CS(17:17:17:16) 5.2.5 MEAS: Measurement Result of a Serving Cell Example: MEAS : CINR(32.1,33.6) RSRP(-75.2,-81.3) RSSI(-49.3,-55.5) RSRQ(-5.9,-5.8) CINR(33.9,32.2) RSRP(-80.2,-87.3) RSSI(-54.3,-61.5) RSRQ(-5.9,-5.8)
CONFIDENTIAL 52 5.2.6 NMEAS: Measurement Result of a Neighbor Cell Example: NMEAS: {39850,501,-75.0,-6.0} 5.2.7 L1D: PHY DL statistics
CONFIDENTIAL 53
CONFIDENTIAL 54 Example: L1D : DCI0=3 DCI={1A(0/3)}{} BLER(0/3,0/0) Dup(0,0) HI(0/4) CFI(796:3:1:0) TB(0,0) TP=1K Layer-Map={1C1L=3,1C2L=0,2C2L=0,2C3L=0,2C4L=0}
CONFIDENTIAL 55 5.2.8 L1U: PHY UL Statistics
CONFIDENTIAL 56 Example: L1U : PUSCH(4)={2(0/3),7(0/1)} PRACH=1 ACK(0/3,0/0) DTX(9,12) PWR(-54.0,-23.3,-48.0,-,-28.1) 5.2.9 MCS: DL/UL MCS statistics Example: MCS : DL={0(0/2),5(0/1)} UL={8(0/4)} PMCH={}
CONFIDENTIAL 57 5.2.10 CSI: Channel State Information Example: CSI : RM(0,10,0,0) A30(0/0/0) P10(10/10/10) RI(0,0,0,0) PMI={} CQI={15(10)}{}
CONFIDENTIAL 58 5.2.11 TP: Throughput Statistics Example: TP : PHY(1K:1K) MAC(1K:1K) RLC(84:79) PDCP(75:73) DIM() IPC(0:0) 5.2.12 MAC Example: MAC : [S] PDU=D{4},U{3}, CE=D{CR1,PAD(0/3)},U{PHR2,BSR(0/3/1),SR(0/2),PAD(0/3)}, I{0,0,0} [S:0] PDU=D{1},U{2} [S:1] PDU=D{2},U{3} [R] RA{0/1}, CE{0,1}, CR{0,0,0} 5.2.13 RLC Example: RLC : [0] PDU=D{T1},U{T1} [1] PDU=D{A1,C1},U{A0/2,C1}, I{0,0,1,0}, STATE=D{1,1},U{2,2}
CONFIDENTIAL 59 5.2.14 DP: Data-path statistics Example: DP : RLC=D0{DC0,AF0,UF0} IPC=D{F0,M0,T0},U{A0,M0,T0} 5.2.15 CIP: Cipher Integrity Statistics Example: CIP : S=0 DL(0,0) UL(0,0) DI(0,0,0) DO(0,0,0) UI(0,0,0) UO(0,0,0) B(0)
CONFIDENTIAL 60 5.3 NAS Protocol Binary Decode 5.3.1 Install decoder Install 3GPP message decoder 5.3.2 Copy NAS Data Copy NAS protocol binary string 5.3.3 Paste to Decoder
CONFIDENTIAL 61 6 Network Connection Examples 6.1 Auto connection (Three bands) Step command Description 1 DM> nv bcfgw 49 0 41 25 26 Write band number into scan list2 DM> nv bcfgsv 1 Write NVRAM back to flash 3 DM>shell Enter shell mode 4 #ucfg set config wan lte vendor 1 Connection manager, lteautocm5 #ucfg set config wan lte autocm manual 0 Lteautocm chooses Auto mode 6 #ucfg set config wan lte atcm use_autocm_req 1 Request to lteautocm 7 #ucfg set config wan lte apntable apn3 ENABLE 1 Enable APN3 8 #ucfg set config wan lte apntable apn3 apn_name <new_APN> Update correct APN, default is internet 9 #reboot 6.2 Auto connection (One band, B41 for example) Step command Description 1 DM> nv bcfgw 49 0 41 Write band number 41 2 DM> nv bcfgsv 1 Write NVRAM back to flash 3 DM>shell Enter shell mode 4 #ucfg set config wan lte vendor 1 Connection manager, lteautocm5 #ucfg set config wan lte autocm manual 0 Lteautocm chooses Auto mode 6 #ucfg set config wan lte atcm use_autocm_req 1 Request to lteautocm 7 #ucfg set config wan lte apntable apn3 ENABLE 1 Enable APN3 8 #ucfg set config wan lte apntable apn3 apn_name <new_APN> Update correct APN, default is internet 9 #reboot 6.3 Manual Connection (Three bands) Step 1 is to configure required information Step command Description 1 DM> nv bcfgw 49 0 41 25 26 Write band number into scan list2 DM> nv bcfgsv 1 Write NVRAM back to flash 3 DM>shell Enter shell mode 4 #ucfg set config wan lte vendor 0 Connection manager, None 5 #ucfg set config wan lte atcm use_autocm_req 0 By itself 6 #ucfg set config wan lte plmn_search_type 2 Search with extension mode 7 #ucfg set plmn search_list 3/3/41/25/26 Assign scan band to scan list 8 #reboot
CONFIDENTIAL 62 Step 2 is using AT commands to enable modem dial up action Step command Description 1 DM>AT+CGDCONT=1,"IPV4V6","APNNAME","",,, APNNAME need to change to your network internet APN name, like ”internet” 2 DM>AT%GPDNTYPE=1,3 Choose APN 3 for internet 3 DM>AT+COPS=5 Choose search extension mode 4 DM>AT+CGACT=1,1 Attached to network 6.4 Manual Connection (One band only) Step 1 is to configure required information Step command Description 1 DM> nv bcfgw 49 0 41 Write band number B41 into scan list 2 DM> nv bcfgsv 1 Write NVRAM back to flash 3 DM>shell Enter shell mode 4 #ucfg set config wan lte vendor 0 Connection manager, None 5 #ucfg set config wan lte atcm use_autocm_req 0 By itself 6 #ucfg set config wan lte plmn_search_type 2 Search with extension mode 7 #ucfg set plmn search_list 3/1/41 Assign scan band to scan list 8 #reboot Step 2 is using AT commands to enable modem dial up action Step command Description 1 DM>AT+CGDCONT=1,"IPV4V6","APNNAME","",,, APNNAME need to change to your network internet APN name, like ”internet” 2 DM>AT%GPDNTYPE=1,3 Choose APN 3 for internet 3 DM>AT+COPS=5 Choose search extension mode 4 DM>AT+CGACT=1,1 Attached to network 6.5 Disconnect Step command Description 1 DM>AT+CGACT=0,1 Deactivate ”1” PDP context 6.6 Get IP Address Step command Description 1 AT+CGCONTRDP=3? Cid=3 Response: AT+CGCONTRDP: 3,6,"internet.lguplus.co.kr","10.118.177.89","10.0.0.166","211.40.215.140","117.111.29.4","","",0 OK Note: ipaddr:10.118.177.879, gateway:10.0.0.166, dns1:211.40.215.140, dns2:117.111.29.4
CONFIDENTIAL 63 7 FW Upgrade 7.1 Using JIG board or CPE board If JIP board is used, GCT LTE window driver and ACM driver are required to install first. When connected PC get IP, 192.168.0.10, from JIG board USB port, GDM7243Q module GUI can be accessed by http://192.168.0.1. Click continuous the web site link to go to main page. If using CPE board, access GCT module by http://192.168.0.1 Select Firmware update from System Link and Select file from filename 1, click update button. For xxx.gz file, RAW Format shall be selected; for xxx.bin, Package Format selected instead. LTE version can be seen from LTEStatus page.

Navigation menu