Sercomm RP131 Wireless PoE Adapter User Manual

Sercomm Corporation Wireless PoE Adapter

User Manual.pdf

RP131 Wireless PoE Adapter Installation Guide Ver.1.1
Page 1 Overview The RP131 (Wireless Adapter) is Wireless client with power supply, it supply the power to the IP camera, it also connect the IP camera to your existing Wireless network.
Page 2 Physical Details Figure 1: RP131(Wireless PoE Adapter)
Page 3 LEDs Power (Green) On - Normal operation. Off - No power. Green On - Associate to WiFi AP Off - Not associate to WiFi AP Flashing - Transmitting/Receiving Data Wireless/WPS Amber On - WPS failed (30 sec) Off - No WPS action or WPS Succeed Flashing - WPS is processing (< 2 min) Ethernet (Green) On - Ethernet connection is active. Off - No Ethernet connection. Flashing - Data is being transmitted or received via the Ethernet Port. PoE (Amber) On - The PoE powered device (PD) is connected and the port is supplying power successfully Off - No PoE powered device (PD) connected
Page 4 Buttons WPS Button Establish a secure connection between the Wireless router (or Access Point) and IP cameraPush-Button-Method - Press and hold the WPS button, but not no more than 3 seconds PIN Method - Press the WPS button and hold for greater than 3 seconds LAN Port Use a standard LAN cable to connect the RP131 to the IP Camera
Page 5 The installation allows the RP131 to directly connect to a wireless router (or Wireless Access Point). You can extend the range of your wireless network.
Page 6 1. Locate the RP131 near the Wireless Access Point while doing the configuration. 2. Make sure the Wireless Access Point is on and working properly. 3. Plug the RP131 into the AC power slot, then the Power LED will remain on. 4. Plug the IP camera into the AC power slot 5. Connect a standard LAN cable from the RP131 to IP camera 6. Push the WPS button on the Wireless Access Point and make sure the Wireless Access Point is in WPS mode. (The LED on the AP will blink and active for 2 minutes.) 7. Push and hold the WPS button on the RP131 for more than 3 seconds. The WPS LED on the device will start blinking for 2 minutes. The RP131 will automatically associate to the Wireless Access Point with the strongest signal and make connections.) 8. The connection of the RP131 and Wireless Access Point is successfully established after the Wireless LED remains on The RP131 (Wireless PoE Adapter) is now ready for use.
Page 7  Dimensions 91.7(L) x 57(W) x 61.2(H) mm Wireless Standards IEEE 802.11 b/g/n Antenna Internal x 2 LEDs 1 * Power 1 * Wireless / WPS 1 * Ethernet 1 * PoE PoE IEEE802.3 af Class 3 Maximum outpout power : 10 Watts DC 48V, 208mA(maximum) Over current protection Data pin : 1, 2, 3, 6 Power pin : 4, 5, 7, 8 Ethernet Interface 1 * RJ45 LAN Port Auto-negotiation, Auto MDI/MDIX Ethernet Standards Ethernet specification IEEE802.3, IEEE802.3u, IEEE802.3x AC Input 100 - 240VAC, 50-60 Hz, 0.8A(maximum) Operating Temperature 0° C to 45° C Storage Temperature -25° C to 70° C Operating 10-90%RH (max) 56.9
Page 8 Humidity Certifications FCC Part 15 Class B Safety Approvals UL Listed (UL60950-1)/cUL CSA No.22-60950-01-03
Page 9 FCC Information to User This device complies with part 15 FCC rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference (2)this device must accept any interference received, including interference that may cause undesired operations. FCC Information to User This device complies with part 15 FCC rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference (2)this device must accept any interference received, including interference thatmay cause undesired operations. This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energyand, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct theinterference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment. This equipment should be installed and operated withminimum distance 20cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available toall US model. Per FCC regulation, all WiFi product marketed in US must fixed toUS operation channels only.

Navigation menu