Sercomm SWSCM01N Z-Wave Smart Chime User Manual

Sercomm Corporation Z-Wave Smart Chime Users Manual

a href="https://usermanual.wiki/Sercomm" itemprop="url"> Sercomm >

Users Manual

1 SW-SCM01N QIG V3.0 SW-SCM01N Z-Wave Smart Chime Installation Guide Z-Wave based wireless chime that allows a user to either enable or extend chime functionality with their doorbell and also enable chime functionality for other Z-Wave and security devices in the user's home. The chime will be implemented per the new Sigma Z-Wave Chime device type and command class. Specification Frequency 908 MHz / 916 MHz Operating Temperature Temperature: 0° - 40°C (32° - 104°F); Humidity: 0% - 80% RH (non-condensing) Storage Temperature Temperature: -20° - 70°C (-4° - 158°F); Humidity: 0% - 90% RH (non-condensing) RF Communication Range Open Air: 70M (Max.) LED Indicator LED x1 Power 120VAC Operating Voltage 120V / 60Hz Dimensions (H x W x D) 55mm x 55mm x 37.5mm Compliance FCC and Z-Wave Plus Package Contents Warnings and Cautions • To be installed and/or used in accordance with appropriate electrical codes and regulations. • If you are unsure about any part of these instructions, please consult a qualified electrician. • To reduce the risk of overheating, do not install near heat sources, such as fires, boilers or heating vents. • Do not install the device facing direct sunlight or in a humid location. • Save this instruction sheet. It contains important technical data, which will be useful for future reference.
SW-SCM01N QIG V3.0 2 Operation 1. Paring Button 2. Green LED Indicator Installation 1. Plug the SW-SCM01N into a wall receptacle. Confirm that the receptacle is working properly. If it is controlled by a wall switch, set to ON all the times. Device Functions The table below summarizes functions supported by the Smart Chime. Function Description Add( Inclusion) 1. Follow your Z-Wave controller's instructions on how to put the controller into "Add" mode. 2. Power on the device. 3. The LED will blink during the inclusion process. This process may take up to 30 seconds. 4. If the device is successfully added to the network, the LED will turn off. The device will return to normal operation. If the process fails, try repeating steps 1 - 3 again. You can also press the Paring button once to put the device into "Add" mode again. Remove( Exclusion) 1. Follow your Z-Wave controller's instructions on how to put the controller into "Remove" mode. 2. Press the Pairing button once. 3. The LED will blink for one second while the device is being removed from the network. 4. If the device was successfully removed from the network, all Z-Wave information will be cleared, and the device will go into "Add" mode for 30 seconds.” Reset to Factory Defaults 1. Hold the Paring button for 10 second until the LED lights up. 2. When LED turns off, all Z-Wave information will be cleared and all settings will be reset to factory defaults. 3. The device will go into "Add" mode Note: Please use this procedure only when the network's primary controller is missing or otherwise inoperable. 1 2
Download:
Mirror Download [FCC.gov]
Document ID3970355
Application IDZOvO7jdEW946Gg3A5OsRkw==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize16.97kB (212129 bits)
Date Submitted2018-08-21 00:00:00
Date Available2018-08-22 00:00:00
Creation Date2018-08-08 02:55:07
Producing SoftwareMicrosoft® Word 2016
Document Lastmod2018-08-21 13:41:22
Document TitleUsers Manual
Document CreatorMicrosoft® Word 2016
FCC ID Filing: P27SWSCM01N

Navigation menu