Sercomm SZBSW01 ZigBee Binary Switch User Manual

Sercomm Corporation ZigBee Binary Switch SZ BSW01 QIG 0129

a href="https://usermanual.wiki/Sercomm" itemprop="url"> Sercomm >

SZ-BSW01-User Manual

1 SZ-BSW01 ZigBee Binary Switch Installation Guide SZ-BSW01 can provide "smart" lighting remote control with its embedded radio frequency (RF) technology that is compatible with ZigBee enabled devices. This device is designed to give you one-touch control of your home's lighting. In a ZigBee network, each device is designed to act as a router. These routers will re-transmit the RF signal from one device to another until the signal is received by the final destination. Using RF technology ensures SerComm to provide great signal through all the obstacles and radio dead spots. The plug-in Lamp Module of SZ-BSW01 is compatible with any ZigBee enabled network, regardless of the manufacturer and can also be used with other devices with the ZigBee logo. CAUTION: Remember to have common sense while using the remote control, especially when scheduling unattended devices. There can be some unexpected consequences if used without care. For example, if an empty coffee pot is remotely turned on, and your coffee pot could be damaged from overheating. Or if an electric heater is turned on by remote control while clothing is draped over it, it may result a fire. DO NOT USE the remote for controlling the high power heating appliances such as portable heaters. This device will not control lighting used with electronic low-voltage and high frequency power supply transformers, nor high pressure discharge lamps (HID lighting), which include mercury-vapor, sodium vapor and metal halide lamps. DO NOT change location after unit is enrolled in ZigBee network. Specification Rado Frequency 2.4GHz RF Communication Range Open Aire：100M (Max) LED Indicator Red / Greed LED x 1 Power Source Input：120 VAC, 0.5A, 50-60 Hz Output Max Current 10A Dimensions (H x W x D) 55 mm x 55 mm x 38 mm (2.15” x 2.15” x 1.48”) Operation Temperature 0° - 50°C (32° - 122°F) Storage Temperature -20° - 70°C (-4° - 158°F) Package Contents Warnings and Cautions  To be installed and/or used in accordance with appropriate electrical codes and regulations.  If you are unsure about any part of these instructions, please consult a qualified electrician.
2 To reduce the risk of overheating and possible damage to other equipments, do not install for controlling a motor-operated appliance, fluorescent lighting fixture, or a transformer supplied appliance.  Unplug unit when servicing the connected lighting fixtures.  Save this instruction sheet. It contains important technical data along with testing and troubleshooting information, which will be useful for future reference. LEDs Power (Red/Green) On (Red) - When ON/OFF button is pressed to ON. Blinking (Green):  The LED will blink for 10 seconds when join/leave function is being processed.  The LED will be on for 1 seconds when join/leave function is succeeded and then off Installation NOTE: In order to use SZ-BSW01 in a ZigBee network, the device must be Included into the network by using a Primary Programmer/Remote. Please refer to the Remote Control instruction sheet for complete information. 1. Put the lamp’s plug into SZ-BSW01. 2. Attach the SZ-BSW01 into wall receptacle. Make sure the receptacle is working properly. If it is controlled by a wall switch, which must be set to ON all the times. WARNING: For use with up to 1000 Watts incandescent lights.
Download:
Mirror Download [FCC.gov]
Document ID1995194
Application IDtBBV5j8l8CcWDDOPNxZK/A==
Document DescriptionSZ-BSW01-User Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize9.99kB (124844 bits)
Date Submitted2013-06-19 00:00:00
Date Available2013-06-19 00:00:00
Creation Date2017-10-26 23:49:05
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-10-26 23:49:05
Document TitleMicrosoft Word - SZ-BSW01_QIG_0129.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: kayla.lin
FCC ID Filing: P27SZBSW01

Navigation menu