Sercomm SZWTD01 ZigBee Water Sensor User Manual Wireless 802 11g Network Camera

Download:
Mirror Download [FCC.gov]
Document ID	2095244
Application ID	EIJCBgyagfj0gUOEOc1M4A==
Document Description	SZ-WTD01 User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.89kB (86173 bits)
Date Submitted	2013-10-18 00:00:00
Date Available	2013-10-18 00:00:00
Creation Date	2013-08-08 14:16:16
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2013-08-08 14:16:27
Document Title	Wireless (802.11g) Network Camera
Document Creator	Acrobat PDFMaker 6.0 for Word
Document Author:	KAREN CHOU

SZ-WTD01 ZigBee Water Sensor Installation Guide
Specification
Frequency
2.4GHz
Battery Type
DC 3V, CR2032x2
Application
Basements, laundry rooms, bathrooms, kitchens etc
Water Sensor Cable Length
3M (10 ft)
Operating Temperature
0° C to 50° C (32° - 122°F)
Storage Temperature
-20° C to 70° C (-4° - 158°F)
Battery Life
2 years
RF Range
Open Air：100M
Dimension
Main Unit: 65 mm x 30 mm x 13 mm (2.60" x 1.18" x 0.51")
Detector Unit: 45 mm x 15 mm x 10 mm (1.77" x 0.59" x 0.39")
Package Contents
Intallation
Intallation
1.
Insert a flat screwdriver into the notch of the casing. Twist carefully to open the front cover.
2.
Install the supplied CR2032 batteries properly.
Note: Please observe the battery polarity to ensure the correct connections while installing the
batteries. Use only the CR2032 batteries for replacement.
3.
Attach the front cover to the device.
4.
Hold the sensor near the top of the door, close to the opening edge of the door. This is the mounting
location for the sensor.
5.
Use either one of the following methods to install the sensor:
•
Remove the back plate of the sensor; use this as the mounting bracket. Use the screwdriver to
secure the back plate to the wall with the screws provided.
•
Use provided adhesive on the sensor. Attach the sensor to the door. Press firmly and hold in place
for a few seconds.
Operation
•
Join Function
SZ-DWS01 v1.0
01/11/12
For "Join" a network, please do the following instruction:
•
•
Put the ZigBee Coordinator into “Permit-Joining” mode.
•
Press the Join/Leave button for less than 1 second. The LED is blinking while processing. If the
sensor has been joined with the ZigBee Coordinator successfully, the Green LED will be on for 2
seconds and then off. The Green LED will be off instantly if failed.
Leave Function
For "Leave" a network, please do the following instruction:
•
Press Join/Leave button for 3 seconds to let the sensor disassociate from the ZigBee Coordinator.
If the sensor has been disassociated successfully with the ZigBee Coordinator, the Green LED
will be on for 1 second and then off.
•
The LED will stay off during the normal operation.
•
The sensor is equipped with a tamper switch. If the cover of sensor is removed, the sensor will send
an alarm to the ZigBee Coordinator. The sensor will be in "Awake" mode before replacing the cover.
SZ-DWS01 v1.0
01/11/12
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment. (Example - use only
shielded interface cables when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
CE Approval
CE Standards
This product complies with the 99/5/EEC directives, including the following safety and EMC standards:
•
EN300328-2
•
EN301489-1/-17
CE Marking Warning
This is a Class B product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
SZ-DWS01 v1.0
01/11/12

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 4
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:1256631d-9d1d-47ed-8a7e-8bc9b76bc8a1
Producer                        : Acrobat Distiller 6.0 (Windows)
Company                         : Accenture
Source Modified                 : D:20130719084941
Headline                        : User Manual
Create Date                     : 2013:08:08 14:16:16+08:00
Creator Tool                    : Acrobat PDFMaker 6.0 for Word
Modify Date                     : 2013:08:08 14:16:27+08:00
Metadata Date                   : 2013:08:08 14:16:27+08:00
Document ID                     : uuid:91100a81-903c-437a-9193-565cfdc9f018
Version ID                      : 6
Format                          : application/pdf
Title                           : Wireless (802.11g) Network Camera
Creator                         : KAREN CHOU
Description                     : User Manual
Subject                         : 
Tagged PDF                      : Yes
Author                          : KAREN CHOU

EXIF Metadata provided by EXIF.tools