Sevylor 2000016013 4010006024 User Manual To The A9f55de9 33ee 42cd 8120 7d18a2c8842a

User Manual: Sevylor 2000016013 to the manual

Open the PDF directly: View PDF PDF.
Page Count: 16

DownloadSevylor 2000016013 4010006024 User Manual  To The A9f55de9-33ee-42cd-8120-7d18a2c8842a
Open PDF In BrowserView PDF
®

INFLATABLE BOATS

®

INFLATABLE BOATS
Including the following Model Series:
Fish Hunter™, Super Caravelle, Caravelle,
Colossus™ and HUI

READ THE FOLLOWING
INSTRUCTIONS AND WARNINGS TO AVOID
DROWNING OR SERIOUS INJURY

WARNING:
•• Not a life saving device.
•• Not for use by children without adult supervision.
•• Always wear an approved Personal Flotation Device
(Life Preserver).
•• Do not overload.
•• Never tow from another boat or vehicle.
•• Use only in water away from debris and obstructions.
•• Do not use in high wind, strong currents, open water or
dangerous tides.
•• Be familiar with the area you intend to use the boat.
•• Never allow diving into or from these boats.
•• Never leave in or near water when not in use.
•• Know and follow local water safety rules and boating
regulations.
•• Use only in protected waters.
•• Do not use this product under the influence of alcohol
or drugs.
•• Do not over inflate.
•• Follow inflation sequence on the product.

®

INFLATABLE BOATS

IMPORTANT INFORMATION
The warnings below relate to various situations. Please observe them.

CAUTION!
Denotes a imminent hazard which will result in severe injury if you
do not comply with the instructions.

WARNING!
Reminds you of safety measures which must be observed. Also
denotes unsafe practices which could result in personal injury or
damage to the product or property, if you do not comply with the
instructions.

CAUTION!
It is the owner's responsibility to make sure all users carefully
read and follow the instructions for safe operation of this
product. Observe all local and national laws. Always wear a
Personal Flotation Device approved by the proper authorities.
Please carefully observe the Capacity Plate information which
is printed on the product.

WARNING!
These boats are not meant for towing because the extreme
pressure of the water while towing can tear the eyelets and/or
handles. These boats are not meant to be used in whitewater.
These boats are made of the highest quality materials and comply
with NMMA (National Marine Manufacturers Association) regulations.

CAUTION!
Altering the construction of these boats could jeopardize the safety
of the occupants and will void the limited warranty.

CAUTION!
Keep boat away from gasoline, battery acid, solvents, etc., as they
can damage the boat.

2

®

INFLATABLE BOATS

INFLATION INSTRUCTIONS
CAUTION!
Do not over inflate. Pressurize product to "Inflation Pressure"
stated in the chart for your specific product.

WARNING!
Never use a compressor, CO2 or compressed air to inflate the boat.
Do not let your boat come into contact with sharp, pointed objects.

To inflate using any Sevylor® QuickPump™ unit:
To begin inflation,
open external
stopper and pull to
extend out.

Attach adapter hose
to inflation end of
QuickPump™ unit.
Insert hose and
turn on.

When fully inflated,
seal valve by
pushing in the pump
nozzle to maintain
seal. Gently back
pump out of valve.

Fully remove adapter
and close external
stopper. Valve should
appear depressed
into itself.

To inflate using the Sevylor® Dual Action Hand Pump or other
inflation device:
To begin inflation,
open external
stopper and pull to
extend out.

Insert nozzle of
inflation device into
the extended valve
and turn on or begin
pumping.

To close valve:
Push in with
inflation device until
stopper has been
depressed, sealing
internal stopper.

Fully remove adapter
and close external
stopper.
Valve should appear
depressed into itself.

3

INFLATABLE BOATS
®

IMPORTANT! Inflate the boat chambers in the following order:
1. Inflate the inside all-around safety chamber.
2. Inflate the floor chamber(s).
3. Inflate the bottom tunnel chambers. (These tubular chambers are
only found on Super Caravelle and Fish Hunter™ models.)
4. Inflate the bustle chamber. (This support chamber positioned at
the stern is found only on the large Super Caravelle models.)
5. Inflate the outside main chamber.
The chambers on the boat will be numbered to indicate order of
inflation also. This order of inflation will ensure the proper volume and
buoyancy of the safety chamber.
Note: To inflate the mini double lock valve, which is used on some of
the Sevylor boat floors and seat bottoms, follow the same inflation
instructions above, using the mini double lock valve adapter. The mini
Double Lock™ valve adapter is included with all Sevylor® pumps.
The adapter can be purchased from Customer Service by calling
1-800-835-3278 (Part Number 5010000707).

CAUTION!
Water temperature and weather does affect the pressure in
inflatable products. In cold weather your product will lose some
pressure due to the fact the air will contract. If this occurs, you
may want to add a little air to improve your products performance.
However, in hot weather, the air will expand. You must let some air
out to prevent your product from failing due to overpressure. You
should avoid exposing your product to extreme temperatures (hot
or cold).

DEFLATION INSTRUCTIONS
Deflation instructions using
any Sevylor® QuickPump™
unit:

Deflation instructions using
the Sevylor® Dual Action
Hand Pump:

Remove adapter hose from inflation end and
attach to opposite deflation end of pump.
Repeat same steps as inflation. This will
draw the air out quickly.

Remove adapter hose from inflation port
and attach to deflation port on pump
handle. Repeat same steps as inflation. This
will draw the air out quickly.

4

WARNING!
Do not exceed the certified maximum capacities under any circumstances!
NMMA (ABYC
Standard)

Persons
Capacity

Maximum Payload Capacity

Engine

Inflation
Pressure

Inflation
Pressure

Model #

Persons Only

Persons, Gear,
Motor
(if applicable)

Max. HP Engine

Main
Chamber(s)

Floor
Chamber(s)

HUI 100

1 Pers. or 190
lbs.

190 lbs.

N/A

0.4 PSI

0.4 PSI

HUI 200

2 Pers. or 370
lbs.

370 lbs.

N/A

0.4 PSI

0.4 PSI

HUI 400

4 Pers. or 650
lbs.

650 lbs.

N/A

0.4 PSI

0.4 PSI

®

INFLATABLE BOATS

Your boat is NMMA certified using the ABYC standard.

WARNING!
Do not exceed the certified maximum capacities under any circumstances!
NMMA (ABYC
Standard)

Persons
Capacity

Maximum Payload Capacity

Engine

Inflation
Pressure

Inflation
Pressure

Model #

Persons Only

Persons, Gear,
Motor
(if applicable)

Max. HP Engine

Main
Chamber(s)

Floor
Chamber(s)

Colossus™
2 Person Boat

2 Pers. or
435 lbs.

435 lbs.

N/A

0.5 PSI

0.5 PSI

Colossus™
3 Person Boat

3 Pers. or
680 lbs.

680 lbs.

N/A

0.5 PSI

0.5 PSI

Colossus™
4 Person Boat

4 Pers. or
840 lbs.

840 lbs.

N/A

0.5 PSI

0.5 PSI

WARNING!
Do not exceed the certified maximum capacities under any circumstances!
NMMA (ABYC
Standard)

Persons
Capacity

Maximum Payload Capacity

Engine

Inflation
Pressure

Inflation
Pressure

Model #

Persons Only

Persons, Gear,
Motor
(if applicable)

Max. HP Engine

Main
Chamber(s)

Floor
Chamber(s)

Caravelle
2 Person Boat

2 Pers. or
300 lbs.

360 lbs.

N/A

0.9 PSI

0.9 PSI

Caravelle
3 Person Boat

3 Pers. or
550 lbs.

600 lbs.

12V Electric
Motor (Sevylor
2000004144)

0.9 PSI

0.9 PSI

Caravelle
4 Person Boat

4 Pers. or
600 lbs.

700 lbs.

3.0 *

0.9 PSI

0.9 PSI

Caravelle
5 Person Boat

5 Pers. or
800 lbs.

900 lbs.

3.0 *

0.9 PSI

0.9 PSI

* Requires 2000004146 Motor Mount Kit (sold separately)
for motors other than Sevylor 12 Volt Motor, Model
2000004144

5

WARNING!

NMMA (ABYC
Standard)

Persons
Capacity

Maximum Payload Capacity

Engine

Inflation
Pressure

Inflation
Pressure

Model #

Persons Only

Persons, Gear,
Motor
(if applicable)

Max. HP Engine

Main
Chamber(s)

Floor
Chamber(s)

Fish Hunter™ 3
Person Boat

3 Pers. or
450 lbs.

600 lbs.

2.0 *

0.9 PSI

0.9 PSI

Fish Hunter™ 4
Person Boat

4 Pers. or
650 lbs.

700 lbs.

4.0 *

0.9 PSI

0.9 PSI

Fish Hunter™ 6
Person Boat

6 Pers. or
900 lbs.

1200 lbs.

3.0 *

0.9 PSI

0.9 PSI

Fish Master™ 4
Person Boat

4 Pers. or
800 lbs.

900 lbs.

3.0 *

1.5 PSI

N/A

®

INFLATABLE BOATS

Do not exceed the certified maximum capacities under any circumstances!

* Requires 2000004146 Motor Mount Kit (sold separately)
for motors other than Sevylor 12 Volt Motor, Model
2000004144

WARNING!
Do not exceed the certified maximum capacities under any circumstances!
NMMA (ABYC
Standard)

Persons
Capacity

Maximum Payload Capacity

Engine

Inflation
Pressure

Inflation
Pressure

Model #

Persons Only

Persons, Gear,
Motor
(if applicable)

Max. HP Engine

Main
Chamber(s)

Floor
Chamber(s)

Super Caravelle
2 Person Boat

2 Pers. or
300 lbs.

360 lbs.

12V Electric
Motor (Sevylor
2000004144)

0.9 PSI

0.9 PSI

Super Caravelle
3 Person Boat

3 Pers. or
550 lbs.

600 lbs.

2.0 *

0.9 PSI

0.9 PSI

Super Caravelle
4 Person Boat

4 Pers. or
600 lbs.

700 lbs.

3.5 *

0.9 PSI

0.9 PSI

Super Caravelle
6 Person Boat

6 Pers. or
900 lbs.

1,100 lbs.

3.5 *

0.9 PSI

0.9 PSI

* Requires 2000004146 Motor Mount Kit (sold separately)
for motors other than Sevylor 12 Volt Motor, Model
2000004144

WARNING!
Do not attempt to mount a motor on any boat that does not state a
Max. HP Engine rating.

6

®

INFLATABLE BOATS

SEVYTEST™ GAUGE
Some of the Sevylor® products are equipped with a Sevytest™
gauge. The Sevytest™ device is a pressure gauge, not an inflation
gauge. The Sevytest™ gauge is found on the side wall, inside the
main chamber(s). The purpose is to show you when to let some air
out after the pressure has increased due to temperature change.
The principle of the Sevytest™ gauge is based on the lengthening of
the PVC under the influence of pressure. Once the boat is properly
inflated, note the position of the Sevytest™ indicator. Then periodically check the Sevytest™ gauge and let out enough air to keep the test
strip in the same general area. If the Sevytest™ indicator is in the “+”
zone, add pressure to the product. If the Sevytest™ indicator is in “-”
zone, release pressure from the product.

Add
pressure
Maintain
pressure
in this
zone

Release
pressure

®

7

®

INFLATABLE BOATS

OPERATING INSTRUCTIONS:
•• Follow all local boating regulations and navigation rules.
Familiarize yourself with boating conditions where you plan to
use the boat. Use common sense and caution when operating in
unfamiliar places.
•• Observe the maximum weight the boat can carry and do not
overload past this limit. Over-loading jeopardizes the safety of the
occupants.
•• Be sure all accessories and/or equipment (e.g. oars, life jackets)
are in proper working condition before using the boat. Each
person occupying the boat is to wear an approved Personal
Flotation Device (life preserver).
•• Sharp objects are not to be carried in the boat without adequate
protection or storage.
•• When navigating the boat in any water depth, watch for
submerged or sharp objects that may damage or pierce the
boat’s air chambers.
•• Enter the boat from the port (left) or starboard (right) sides - not
from the fore (front) or aft (back) sides.
•• Never tow with a boat or any other vehicle.

MOTOR MOUNTING
WARNING!
Do not mount a motor on any boat that exceeds the Maximum
Horsepower Rating for your specific boat model.
All Sevylor® boats that have a Horsepower Rating can accept the
Sevylor® 12V Trolling Motor, Model 2000004144 without purchasing
any additional mounting hardware. Refer to 12V Trolling Motor
mounting instructions.
Mounting any motor other than the Sevylor® 12V Trolling Motor,
Model 2000004144, requires the Sevylor® Motor Mount Kit, Model
2000004146, which is sold separately.

CARE & STORAGE:
•• These boats are made of the highest quality materials and
comply with NMMA (National Marine Manufacturers Association)
regulations. Altering the construction of these boats will void the
limited warranty and could jeopardize the safety of the occupants.
•• If your boat has been used in salt water, rinse it off with fresh
water as soon as possible.
•• Remove tar spots or other soiled areas by using a mild soap and
rinsing with fresh water.
•• Be sure your boat is completely dry before storing.
•• The boats may be stored inflated, but do not place any heavy or
sharp objects on it. Storage is best in a dry room.
8

Fittings for
Motor Mount

Carry
Handle

Inflated
Floor
Fittings for
12V Motor
Grab Line

4 Oar locks
Double as Handles

DIN Safety
Chamber

®

INFLATABLE BOATS

Caravelle Models
5 PERSON

Fittings for
Motor Mount

4 PERSON

Carry
Handle

Inflated
Floor
Fittings for
12V Motor
Grab Line

4 Oar locks
Double as Handles

3 PERSON

DIN Safety
Chamber
Fittings for
12V Motor
Inflated
Floor

Grab Line

2 Oar locks
Double as Handles

DIN Safety
Chamber
Fittings for
12V Motor

2 PERSON

Inflated
Floor

Grab Line
2 Oar locks
Double as Handles

DIN Safety
Chamber

9

Fittings for
Motor Mount

Inflatable
Seat
Carry
Handle

Inflatable
Seat
Fittings for
12V Motor
Grab Line
®
Exterior Tunnel 4 Patented Delrin
Swivel Oar Locks
Chambers

DIN Safety
Chamber

®

INFLATABLE BOATS

Super Caravelle Models
6 PERSON

Fittings for
Motor Mount

4 PERSON

Carry
Handle

Inflatable
Seat
Fittings for
12V Motor
Grab Line
Exterior Tunnel 4 Patented Delrin®
Swivel Oar Locks
Chambers

DIN Safety
Chamber

3 PERSON
Fittings for
Motor Mount
Fittings for
12V Motor

Carry
Handle

Grab Line
Exterior Tunnel
Chambers

2 Molded
Oar Locks

DIN Safety
Chamber

2 PERSON
Fittings for
12V Motor

Grab Line

10

Exterior Tunnel
Chambers

2 Molded
Oar Locks

DIN Safety
Chamber

4 PERSON

4 Air
Chambers

Front
Handle

®

INFLATABLE BOATS

Colossus™ Models

Grab Line
4 Oar Locks

8 Rope Holders
with Oar Storage
Clips

3 PERSON

Front
Handle

4 Air
Chambers

Grab Line
2 Oar Locks

8 Rope Holders
with Oar Storage
Clips

2 PERSON

Front
Handle

3 Air
Chambers

Grab Line
2 Oar Locks

8 Rope Holders
with Oar Storage
Clips

11

®

INFLATABLE BOATS

Fish Hunter™ Models
6 PERSON

Oar Holders

Inflatable
Seat

Fishing Rod
Holder

Front Fittings
for 12V Motor

Carry
Handle
Fittings
for Motor
Mount

Carry
Handle

Rear Fittings
for 12V Motor

Grab Line
Exterior Tunnel
Chambers

Inflatable
Seat

4 Swivel
Oar Locks

4 PERSON
Inflatable
Seat

Chafing
Pads

Chafing
Pads

Battery Gear Bag Fishing Rod
Pouch
Holder
Oar Holders
Fishing Rod
Holder

Front Fittings
for 12V Motor

Carry
Handle
Fittings
for Motor
Mount

Carry
Handle

Rear Fittings
for 12V Motor
Inflatable
Seat

Grab Line

Exterior Tunnel
Battery Gear Bag Fishing
4 Swivel
Chambers
Rod Holder
Oar Locks Pouch

3 PERSON
2 Swivel
Oar Locks

Oar Holders

Fishing Rod
Holder

Carry
Handle

12

Fittings for
Motor Mount
and Outboard
Motor up to
2HP and 12V
Motors
Carry
Handle

Grab Line
Exterior Tunnel
Chambers

Gear Bag Chafing
Pads

Inflatable
Seat

HUI 400

DIN Safety Chamber

Carry
Handle

®

INFLATABLE BOATS

HUI Models

Grab Line
4 Oar Locks

HUI 200

Main Chamber

Inflated
Floor- 2
Chambers

DIN Safety Chamber

Grab Line
2 Oar Locks
Main Chamber

HUI 100

2 Oar Locks

Inflated
Floor- 2
Chambers

DIN Safety Chamber

Inflated
Floor- 2
Chambers

Grab Line
Main Chamber

13

IMPORTANT: To properly install the inflatable boat’s grab line, first
inflate the boat. Feed the grab line through the eyelets on each of the
rope holders. Then tie the two loose ends in a square knot at the rear
of the boat.

Square Knot

OAR ASSEMBLY:

(for models with oar included)

®

INFLATABLE BOATS

GRAB LINE INSTALLATION:

Join the two shafts together by screwing them together into the
coupler. Attach the blade to the shafts by screwing in into the bottom
of the shaft.
Replacement Part #2000004151
Coupler
Retainer
Ring

Blade
Shaft

Shaft

The assembled oar is to be inserted into the oar locks from the
outside of the boat. The oar retainer ring is then placed onto the top
half of the assembled oar, from the inside of the boat, to prevent the
oar from sliding into the water (see below).

14

®

INFLATABLE BOATS

REPAIRING SMALL PUNCTURES
For inadvertent punctures, you can repair them with the included
Sevylor® repair patch.
INSTRUCTIONS:
1. Thoroughly clean and dry the damaged area. Completely deflate
if an inflatable article.
2. Cut a portion of the patch to cover the puncture, and allow an
additional ¼” on all sides. Always cut a round or oval patch. Never
leave corners.
3. Be sure the spot is completely dry.
4. Peel the backing from the patch.
5. Adhere the patch to the puncture.
6. Using your thumb or finger apply even pressure across the entire
surface of the patch.
The Sevylor® AirSeal repair kit is also another repair option available
(Model # 2000003730 - not included). Sevylor® AirSeal is a fast,
reliable repair for vinyl inflatables: air mattresses, toys, pools, boats
as well as rainwear, groundsheets, golf bags, etc.
INSTRUCTIONS:
1. Thoroughly clean and dry the damaged area. Completely deflate
if an inflatable article.
2. When the damage is small (a pin hole or tear under 2 inches)
apply a light coat of AirSeal two or three times. Allow five minutes
to dry between each application.
3. For heavier material, e.g. fabric backed vinyl or a vinyl boat, apply
up to five coats allowing a five-minute drying period between
coats.
4. Ensure the AirSeal is completely dry before resuming use of the
article.
5. When the damage is more extensive, cut a patch (with rounded
corners) using any vinyl material. Generously coat the damaged
area spreading the AirSeal at least 3/8” from the torn edges. Apply
the patch and apply AirSeal to all edges of the patch making a
seal between patch and the item being repaired. Allow the article
to dry at least 10 hours before using.
Contains sufficient material for several small repairs.
AirSeal is intended for use with 100% PVC (poly vinyl chloride) only.
Do not use with any other material.
You may purchase the Sevylor® repair patch (Model # 2000003731)
and Sevylor® AirSeal (Model # 2000003730) by calling Coleman
Customer Service at 1-800-835-3278 or going to www.sevylor.com.
15

®

INFLATABLE BOATS

Limited 90 Day Warranty
The Coleman Company, Inc. (“Coleman”) warrants that for a period of 90 days from the date
of original retail purchase, this product will be free from defects in material and workmanship.
Coleman, at its option, will repair or replace this product or any component of the product found to
be defective during the warranty period. Replacement will be made with a new or remanufactured
product or component. If the product is no longer available, replacement may be made with a
similar product of equal or greater value. This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is
not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty
performance. Coleman dealers, service centers, or retail stores selling Sevylor® products do not
have the right to alter, modify or in any way change the terms and conditions of this warranty.
What This Warranty Does Not Cover
This warranty does not cover normal wear of parts, parts that are not genuine Coleman® parts,
or damage resulting from any of the following: negligent use or misuse of the product; commercial
use of the product; use contrary to the operating instructions; disassembly, repair or alteration by
anyone other than Coleman or an authorized service center. Further, the warranty does not cover
Acts of God, such as fire, flood, hurricanes and tornadoes. Warranty void if damage to the product
results from the use of a part other than a genuine Sevylor® part.
COLEMAN SHALL NOT BE LIABLE FOR DEFECTS THAT ARE CAUSED BY THE USE
OF UNAUTHORIZED PARTS OR SERVICE. COLEMAN SHALL NOT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY OR CONDITIONS. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE IS LIMITED IN DURATION TO THE DURATION OF THE ABOVE
WARRANTY OR CONDITIONS. SOME STATES OR JURISDICTIONS DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE.
How to Obtain Warranty Service
Take the product to an authorized Coleman service center. You can find the nearest authorized
Coleman service center by visiting www.coleman.com or calling 1-800-835-3278 or
TDD 1-316-832-8707. If a service center is not conveniently located, attach to the product a tag
that includes your name, address, daytime telephone number and description of the problem.
Include a copy of the original sales receipt. Carefully package the product and send either by
courier or insured mail with shipping and insurance prepaid to:
The Coleman Company, Inc.
3600 North Hydraulic
Wichita, KS 67219
The costs of transporting the product to Coleman or an authorized service center for warranty
service is the responsibility of the purchaser.
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
If you have any questions regarding this warranty please call 1-800-835-3278 or
TDD 1-316-832-8707.

© 2010 The Coleman Company, Inc. All rights reserved.
QuickPump™, Fish Hunter™, Double Lock™ and Colossus™ are trademarks of The Coleman
Company, Inc. Sevylor® is a registered trademark and is a trademark of Sevca, LLC.

®

3600 North Hydraulic • Wichita, KS 67219 U.S.A.
1-800-835-3278 • www.Sevylor.com
4010006024 (20100105)



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Signing Date                    : 2010:01:07 08:55:33-06:00
Signing Authority               : ARE Acrobat Product v8.0 P23 0002337
Annotation Usage Rights         : Create, Delete, Modify, Copy, Import, Export
XMP Toolkit                     : Adobe XMP Core 4.0-c320 44.284297, Sun Apr 15 2007 17:19:00
Instance ID                     : uuid:c4ebdba0-3364-4e05-94da-bc481a7a8f32
Document ID                     : adobe:docid:indd:d027358a-e46c-11de-aa14-98834ea76c29
Rendition Class                 : proof:pdf
Derived From Instance ID        : d0273589-e46c-11de-aa14-98834ea76c29
Derived From Document ID        : adobe:docid:indd:9809dda6-a740-11de-aa24-b1da88f98063
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:43b6b067-d921-11d7-b64a-813019035c22, uuid:942A3DD28DE4DE11875293292645E040, uuid:942A3DD28DE4DE11875293292645E040, uuid:942A3DD28DE4DE11875293292645E040, uuid:942A3DD28DE4DE11875293292645E040, uuid:C14B7DF6F923DE11A410BA7E0D156934, uuid:C14B7DF6F923DE11A410BA7E0D156934, uuid:C14B7DF6F923DE11A410BA7E0D156934, uuid:C14B7DF6F923DE11A410BA7E0D156934, uuid:03497B1EAB66DE11920081DAF2A0F392, uuid:06497B1EAB66DE11920081DAF2A0F392, uuid:f5808a7c-322d-4b65-93a1-60522d4e3afd, uuid:D138CD724D61DE11B7F2B05ECAD28F79, uuid:CA38CD724D61DE11B7F2B05ECAD28F79, uuid:AB882FD2FB61DE11844EF5B33F684A0E, uuid:36444F784C61DE11B7F2B05ECAD28F79, uuid:ACF455515361DE11B7F2B05ECAD28F79, uuid:F867E1E75261DE11B7F2B05ECAD28F79, uuid:BAE4D2575261DE11B7F2B05ECAD28F79, uuid:169206A44F61DE11B7F2B05ECAD28F79, uuid:7450780A5761DE11B7F2B05ECAD28F79, uuid:695D113B5661DE11B7F2B05ECAD28F79, uuid:625D113B5661DE11B7F2B05ECAD28F79, uuid:CDC6A7196061DE11B7F2B05ECAD28F79, uuid:666E9B4C5861DE11B7F2B05ECAD28F79, uuid:666E9B4C5861DE11B7F2B05ECAD28F79, uuid:F1CC529B6461DE11B7F2B05ECAD28F79, uuid:a4447a96-b0eb-442a-ab53-33cf990d9417, uuid:99677106ABA8DE11BEECC334E86D3996, uuid:dd742ca4-e9cb-4e91-8a86-22b71c014e45, uuid:ee858389-4ab7-43f6-b31a-f43f7113f0d0, uuid:1c91b4c7-69ff-422e-be3a-3ae116a1557c, uuid:01097977-3163-4785-82df-bb43fbdc2f53
Manifest Reference Document ID  : adobe:docid:photoshop:43b6b05e-d921-11d7-b64a-813019035c22, uuid:BE4B7DF6F923DE11A410BA7E0D156934, uuid:BE4B7DF6F923DE11A410BA7E0D156934, uuid:BE4B7DF6F923DE11A410BA7E0D156934, uuid:BE4B7DF6F923DE11A410BA7E0D156934, uuid:C04B7DF6F923DE11A410BA7E0D156934, uuid:C04B7DF6F923DE11A410BA7E0D156934, uuid:C04B7DF6F923DE11A410BA7E0D156934, uuid:C04B7DF6F923DE11A410BA7E0D156934, uuid:01497B1EAB66DE11920081DAF2A0F392, uuid:04497B1EAB66DE11920081DAF2A0F392, uuid:7FF6C0CF0F62DE1192B9C19AA8EEC615, uuid:00B499683961DE11B7F2B05ECAD28F79, uuid:03DAE9A13961DE11B7F2B05ECAD28F79, uuid:AA882FD2FB61DE11844EF5B33F684A0E, uuid:BBB105E93961DE11B7F2B05ECAD28F79, uuid:A091C4003A61DE11B7F2B05ECAD28F79, uuid:A2BA713C3A61DE11B7F2B05ECAD28F79, uuid:A3FD6C3F3A61DE11B7F2B05ECAD28F79, uuid:B066F0543A61DE11B7F2B05ECAD28F79, uuid:45295F6C3A61DE11B7F2B05ECAD28F79, uuid:727DCF813A61DE11B7F2B05ECAD28F79, uuid:93B7A4903A61DE11B7F2B05ECAD28F79, uuid:AC186AA43A61DE11B7F2B05ECAD28F79, uuid:3884EED73A61DE11B7F2B05ECAD28F79, uuid:3884EED73A61DE11B7F2B05ECAD28F79, uuid:2DC700A33B61DE11B7F2B05ECAD28F79, uuid:9A677106ABA8DE11BEECC334E86D3996, uuid:98677106ABA8DE11BEECC334E86D3996, uuid:F56E7E27EF61DE11BD17D9484E54A56D, uuid:F76E7E27EF61DE11BD17D9484E54A56D, uuid:F96E7E27EF61DE11BD17D9484E54A56D, uuid:FB6E7E27EF61DE11BD17D9484E54A56D
Create Date                     : 2010:01:05 11:02:19+08:00
Modify Date                     : 2010:01:07 08:55:33-06:00
Metadata Date                   : 2010:01:07 08:55:33-06:00
Creator Tool                    : Adobe InDesign CS3 (5.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 12288 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : 4010006024.indd
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Has XFA                         : No
Page Count                      : 16
Creator                         : Adobe InDesign CS3 (5.0)
EXIF Metadata provided by EXIF.tools

Navigation menu