Shandong USR IOT Technology USRGM3 Serial to GPRS Module User Manual
Shandong USR IOT Technology Limited Serial to GPRS Module
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3209102 |
| Application ID | NYTwXJ4N4vMb67r15p0LbA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 174.25kB (2178136 bits) |
| Date Submitted | 2016-11-28 00:00:00 |
| Date Available | 2016-11-28 00:00:00 |
| Creation Date | 2016-06-07 16:04:27 |
| Producing Software | PDFdo.com 5.5.6.0 |
| Document Lastmod | 2016-10-09 17:50:13 |
| Document Title | User Manual |
USR-GM3/GM3s User Manual
www.usriot.com
USR-GM3/GM3s User Guide
(USR-GM3/GM3s )
File version: Ver1.08
USR-GM3/GM3s is highly-integrated UART to GSM/GPRS module, Users can easily make
communication between serial device and cellphone and network device with it.
This module is different from the common modules on the market, it is the smallest GPRS DTU,
plug-and-play device. USR-GM3s will be with SIM card inside, more easier to use, it just need
power supply.
Jinan USR IOT Technology Limited
1 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
Content
USR-GM3/GM3s User Guide......................................................................................................................................... 1
Quick Start.........................................................................................................................................................................3
1.1. Testing environment......................................................................................................................................... 3
1.2. Transmission..................................................................................................................................................... 4
2. Introduction................................................................................................................................................................... 6
2.1. Short Description.............................................................................................................................................. 6
2.2. Characteristic.................................................................................................................................................... 6
2.3. Features.............................................................................................................................................................6
2.4. Application Field................................................................................................................................................7
3. Hardware.......................................................................................................................................................................8
3.1. Pin Description..................................................................................................................................................8
3.1.1. Outside View..........................................................................................................................................8
3.1.2. Pin Assignment（Top）....................................................................................................................... 8
3.1.3. PCB Layout............................................................................................................................................ 8
3.1.4. Pin Description.......................................................................................................................................9
3.1.5. Outside Antenna.................................................................................................................................. 11
3.2. Hardware Block Diagram.............................................................................................................................. 11
4. Module Functions...................................................................................................................................................... 11
4.1. Work Mode...................................................................................................................................................... 12
4.1.1. Switching Work Mode.........................................................................................................................12
4.1.2. Network transmission......................................................................................................................... 12
4.1.3. HTTPD Function................................................................................................................................. 20
4.1.4. SMS Message Transmission.............................................................................................................23
4.2. Register Package........................................................................................................................................... 27
4.2.1. Description........................................................................................................................................... 28
4.2.2. Usage....................................................................................................................................................28
4.3. Heart Beat Package.......................................................................................................................................29
4.3.1. Description........................................................................................................................................... 30
4.3.2. Usage....................................................................................................................................................30
4.4. UART................................................................................................................................................................31
4.4.1. RS485...................................................................................................................................................32
4.4.2. Similar RFC2217.................................................................................................................................32
5. Parameters Setting....................................................................................................................................................33
5.1. Operating AT command.................................................................................................................................34
5.2. AT Command Format.....................................................................................................................................35
5.3. AT Command Set........................................................................................................................................... 37
Appendix A: Contact......................................................................................................................................................54
Appendix B: Disclaimer.................................................................................................................................................55
Appendix C: Update History......................................................................................................................................... 55
Jinan USR IOT Technology Limited
2 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
Quick Start
This chapter is a quick start guide for using USR-GM3/GM3s module. If it is the first time to
use
USR-GM3/GM3s for you, you should read this chapter carefully, and then follow the tips,
try to do
some tests by yourself. It will help you to know about USR-GM3/GM3s generally. If
you have experience of using USR-GM3/GM3s, please escape this chapter.
In this chapter, you will be told how to make communication between serial device and TCP
server. Under default setting, GM3 module works in network transmission mode, it connects
to our TCP test server, address is test.usr.cn, port is 2317. The server will respond what it
receives.
All the software used in this document can be obtained from our website www.usriot.com
www.usriot.com.
You can also access USR customer support center: http://h.usriot.com
http://h.usriot.com.
1.1. Testing environment
The voltage of module is TTL 3.3V, so you should not connect it with computer serial port
directly, an adapter is necessary.
NOTE:
K(Evaluation Kit) , it
1. If it is the first time to use our module for you, please use our EV
EVK(Evaluation
may save you lot of trouble and time.
2. keep default setting in this test.
Jinan USR IOT Technology Limited
3 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
1.2. Transmission
1. Put SIM card into the socket on EVK, connect COM1 to PC’s serial port with cable.
2. Open test software ”USR-TCP232-Test”, set right serial port number and baud rate, and
open it. As the following figure.
3. Power up the EVK with DC 5V adapter, then the POWER led will be on, several seconds
later, the WORK led will twinkle, and then GPRS LINKA led will be on.
Jinan USR IOT Technology Limited
4 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
Meaning of led:
POWER
WORK
GPRS
LINKA
LINKB
DATA
4.
“on” means normal power supply, “off” means power supply failure.
“blink” means running correctly, “off” means not running.
“on” means attached, “off” means attach failure.
“on” means socket A has connected to server, “off” means not connect.
“on” means socket B has connected to server, “off” means not connect.
“blink” means transmission, “off” means no transmission.
Wait for LINKA led on, send data to module via serial port. For example, if you send
“www.usr.cn”, at the same time, the DATA led will be on for a while. Then, you will get
“www.usr.cn” in the receiving window from our test server.
Jinan USR IOT Technology Limited
5 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
2. Introduction
2.1. Short Description
USR-GM3/GM3s is new listing at 2015, it is one embedded GSM module. USR-GM3/GM3s
is designed
for embedded system, it is so small and convenient that you can integrate it to
your system
easily.
2.2. Characteristic
�
�
�
�
�
�
�
�
�
�
�
�
Small and completed function GPRS DTU, transmission between serial and GPRS
Support GSM850/900,DCS1800/1900
Support GSM/GPRS/EDGE, support 2G/3G/4G SIM card, but based on 2G network
Support 2 sockets, Support TCP and UDP
4KB cache for each of sockets, user can choose to cache data or not
Support register package and heart beat package
Support setting parameters via SMS message
Support 4 work modes: SMS message transmission mode, network transmission mode
and HTTPD mode
Support basic and extend AT command sets
Support similar RFC2217
Support flow control: RTS/CTS
Support RS485
2.3. Features
�
�
�
�
�
�
�
Baud rate: 2400, 4800, 9600, 14400, 19200, 28800, 33600, 38400, 57600 115200,
230400, 460800, 921600.
Operating voltage: 3.40V~4.20V
Operating current: average 55mA~80mA, maximum 750mA
Operating temperature: -25~+85°C
Storage temperature: -40~+125°C
Storage humidity: 5%~95%RH
Max TX power : GSM900 class4(2W)，DCS1800 class1(1W)
Jinan USR IOT Technology Limited
6 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
2.4. Application Field
� In power industry, USR-GM3/GM3s can embedded in the electric meter, power application
terminals
and
other
equipment
to
realize
of
reactive
power
compensation monitoring, distribution monitoring, meter collection and copy,
street lamp controlling and other applications, to achieve smart city.
� In Heating field, USR-GM3/GM3s can be embedded in m-BUS concentrator to achieve the
integration of the concentrator and wireless communication.
� In water industry, USR-GM3/GM3s is also plays a significant role in system of water set co
py, water resource management and remote monitoring, wireless communication of water
pipe network monitoring.
� In Environmental protection , USR-GM3/GM3s module can be integrated into the on-line
monitoring system of flue gas on-line monitoring (CEMS), water quality online monitoring.
� In the field of equipment maintenance ( Equipment maintenance field),USR-GM3/GM3s use
in the system of equipment remote monitoring, such as elevator monitoring, air conditioning
monitoring.
� Other GPRS communication applications .
Jinan USR IOT Technology Limited
7 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
3. Hardware
3.1. Pin Description
Outside View
3.1.1.
3.1.1.Outside
Pin Assignment
Top
3.1.2.Pin
Assignment（Top
Top）
3.1.2.
Jinan USR IOT Technology Limited
8 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
PCB Layout
3.1.3.
3.1.3.PCB
Jinan USR IOT Technology Limited
9 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
Pin Description
3.1.4.
3.1.4.Pin
Note: ‘P’ for power, ‘I’ for input, ‘O’ for output, ‘N’ for not connect
Pin
Name
Type
Description
VCC
Power supply，3.4V to 4.2V
VCC
Power supply，3.4V to 4.2V
GND
Power ground
GND
Power ground
Reload
Pull-down 1s restore default setting, >3s restore factory setting
NC
Keep no connecting
RS485
Control RS485 RX/TX
NC
Keep no connecting
Reset
Restart, pull-down 1s for restart
10
GPRS
GPRS status, high for attached, low for not attached
11
LINKA
Socket A status, high for connected, low for not connected
12
LINKB
Socket B status, high for connected, low for not connected
13
DATA
Data status, high for transmission, low for not transmission
14
WORK
Running status, high for normal, low for failure
15
SHUT
Shut down, pull-down for shut module
16
NC
Keep no connecting
17
GND
Power ground
18
SPEAKER-
Speaker negative terminal
19
SPEAKER+
Speaker positive terminal
20
MIC-
Microphone negative terminal
21
MIC+
Microphone positive terminal
22
VSIM
Power supply for SIM card
23
SIM_CLK
Clock line for SIM
24
SIM_DAT
I/O
Data line for SIM
25
SIM_RST
Reset line for SIM
26
NC
Keep no connecting
27
HST_TXD
Upgrade from uart
28
HST_RXD
Upgrade from uart
29
V_PAD
2.8V output
30
NC
Keep no connecting
31
NC
Keep no connecting
32
NC
Keep no connecting
33
NC
Keep no connecting
Jinan USR IOT Technology Limited
10 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
34
NC
Keep no connecting
35
TXD1
TX line for uart1
36
RXD1
RX line for uart1
37
CTS1
CTS line for uart1
38
RTS1
RTS line for uart1
39
GND
Power ground
40
GND
Power ground
41
RF
RF output
42
GND
Power ground
www.usriot.com
Outside Antenna
3.1.5.
3.1.5.Outside
1. The line of Antenna should be short to make the insert loss lower and routed as RF
line strictly to keep 50ohm matching.
2. It’s better to put the antenna pad on the edge of the PCB.
3.2. Hardware Block Diagram
The interface module provides includes: power input, output, on/off control, reset to restart
control, control, restore the factory Settings, working module, analog audio input, output, UART,
SIM, RF antenna.
Jinan USR IOT Technology Limited
11 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
4. Module Functions
4.1. Work Mode
USR-GM3/GM3s module can work in 3 modes
� SMS message transmission mode
� network transmission mode
� HTTPD mode
Switching Work Mode
4.1.1.
4.1.1.Switching
Choose by button you want to work mode
And then select save all parameters
Can save the default parameters for the user, click on the restart after effective working
mode.
Note: if you can't find the above tool buttons please refer to the picture's position on the
drive, you can see the hidden button
Jinan USR IOT Technology Limited
12 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
Network transmission
4.1.2.
4.1.2.Network
4.1.2.1.
Description
TCP/UDP
PC
Internet
data
TCP/UDP
data
GM3
Serial data
Serial device
Under this mode, customer’s serial device can send data to TCP or UDP server via this
module, Module can also receive data from server, and transmit the data to customer’s
serial device.
Customers don’t need to know the detail of communication, just need some simple setting.
GM3 support 2 sockets, socket A and socket B, they are standalone with each other. GM3
only supports TCP Client and UDP Client.
4.1.2.2.
Application Scenarios
If user want to make communication between serial devices and devices on the network,
but in the place where serial device stays using router to connect to network is not
convenient for user. But signal from base station is available, so GM3 module can build a
bridge between serial device and devices on the network .
4.1.2.3.
Usage
Note: All the AT commands terminate with carriage return(0x0D), we ignore it here.
About how to use AT commands, please refer to chapter 5.
We have one software for customers to use, customers can get it from our
http://www.usriot.com/Download/248.html.
website:http://www.usriot.com/Download/248.html.
And we have one software for customers to do serial and network tests, customers can get
http://www.usriot.com/Product/78.html
it from our website:http://www.usriot.com/Product/78.html
http://www.usriot.com/Product/78.html.
Jinan USR IOT Technology Limited
13 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
1. Set TCP server software, log in remote server via remote desktop connection.
Then open network test software, set the parameters as the bellowing.
Jinan USR IOT Technology Limited
14 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
2. Set Module Parameters
1) Set work mode as network transmission
2) Enable socket A
3) Set socket A as TCP client, server address is test.usr.cn(domain), server port is 10000.
3. Restart GM3, wait the connection of socket A has been established, send data to
module via serial port, then you will get data at network server software. And send data
to module via network, then the data will be got at module serial port.
Jinan USR IOT Technology Limited
15 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
Jinan USR IOT Technology Limited
16 / 55
www.usriot.com
tec@usr.cn
USR-GM3/GM3s User Manual
4.1.2.4.
www.usriot.com
Special Type Of Sending Command
Besides under “AT command mode”, customers can also send At commands under network
transmission mode via serial or network. This kind of commands is different from common ones,
customers should add command password and # at the front of common command string,.
Note: every command string should terminate with carriage return. Here we use [0D].
Jinan USR IOT Technology Limited
17 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
4.1.2.4.1. Serial AT Command
1. Set work mode as network transmission.
2. Enable serial command function.
3. Query command password.
After setting successful, restart GM3, then send “usr.cn#AT+VER” via serial.
Then GM3 will respond the firmware version.
Jinan USR IOT Technology Limited
18 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
4.1.2.4.2. Network AT command
1. Enable network command function.
2. Query command password.
Besides, customers need to configure socket A or socket B for network connection, refer to
Jinan USR IOT Technology Limited
19 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
chapter 4.1.2.3. After setting successful, restart GM3. When connection is establishing,
send “usr.cn#AT+VER” from network.
Jinan USR IOT Technology Limited
20 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
HTTPD Function
4.1.3.
4.1.3.HTTPD
4.1.3.1.
Description
HTTP
HTTP
Internet
data
HTTP
data
GM3
server
Serial data
Serial device
Under this mode, customer’s serial device can request data from HTTP server via this
module, Module can also receive data from HTTP server, analysis the data and transmit the
data to customer’s serial device.
Customers don’t need to know the detail of communication, just need some simple setting.
4.1.3.2.
Application Scenarios
If customer want to request data from HTTP server, and customer’s serial device can’t
connect to Internet via a router. But signal from base station is available, so customer can
use GM3 module to make this communication. Customer just need to do some simple
setting, and send request data. GM3 could get the result from HTTP server, and analysis it
to get the useful data, send the data to serial device.
4.1.3.3.
Usage
Note: All the AT commands terminate with carriage return(0x0D), we ignore it here.
About how to use AT commands, please refer to chapter 5.
We have one software for customers to use, customers can get it from our
http://www.usriot.com/Download/248.html.
website:http://www.usriot.com/Download/248.html.
And we have one software for customers to do serial and network tests, customers can get
Jinan USR IOT Technology Limited
21 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
http://www.usriot.com/Product/78.html
it from our website:http://www.usriot.com/Product/78.html
http://www.usriot.com/Product/78.html.
1. Setting
1) Set work mode as HTTPD.
2) Set request type as GET.
3) Set the address of HTTP server as “www.usr.cn”, and set server port as 80.
4) Set the request URL as ”/1.php?”
5) Set request head string.
”Accept:text/html[0D][0A]Accept-Language:zh-CN[0D][0A]User-Age
Mozilla/5.0[0D][0A]Connection: Keep-Alive[0D][0A]
Keep-Alive[0D][0A]””
nt:
NOTE:
[0D] means carriage return, it is 0x0D in hex number. [0A] means line feed, it is
0x0A in hex number. Because this kind of data is not able to be put into AT commands
string, so it is tropical. The rule is two bytes in [] means one byte in hex form.
For example,
Jinan USR IOT Technology Limited
22 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
“[0D]” means carriage return, 0x0D in hex number.
“[20]” means space, 0x20 in hex number.
2. Restart module, then send “data=www.usr.cn” to HTTP server via serial port，you will
get [www.usr.cn] from server.
NOTE: the server “www.usr.cn” is USR’s HTTP test server, if you send
“data=www.usr.cn” to it, it will feed back the data after “=” with “[]” including.
In the step 1, serial device send “data=www.usr.cn” to GM3, then GM3 prepares
package with head information set before, so the package data is:
GET /1.php?data=www.usr.cn HTTP/1.1
Host: www.usr.cn
Accept:text/html
Accept-Language:zh-CN
User-Agent: Mozilla/5.0
Connection: Keep-Alive
HTTP
After sending data, GM3 receives data:
HTTP/1.1 200 OK
Date: Wed, 24 Jun 2015 04:08:35 GMT
Server: Apache/2.0.63 (Win32) mod_ssl/2.0.65 OpenSSL/0.9.8o PHP/5.2.14
X-Powered-By: PHP/5.2.14
Cache-Control: max-age=600
Expires: Wed, 24 Jun 2015 04:18:35 GMT
Content-Length: 19
Keep-Alive: timeout=15, max=99
Connection: Keep-Alive
Content-Type: text/html
[www.usr.cn]
After GM3 receives the above data, it will analysis the information, and send the result to
serial device.
Jinan USR IOT Technology Limited
23 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
SMS Message Transmission
4.1.4.
4.1.4.SMS
4.1.4.1.
Description
Base station
cell
phone
SMS
SMS
GM3
Serial data
Serial
Device
Under this mode, customer’s serial device can send SMS message to a cell phone via this
module, Module can also receive SMS message from cell phone, and transmit the message
in serial data to customer’s serial device.
Customers don’t need to know the detail of communication, just need some simple setting.
4.1.4.2.
Application Scenarios
If user’s device is a serial device, it is placed at remote area. User wants to communicate
with this device by SMS message, to check what status the device is in, or to control the
device.
4.1.4.3.
Usage
Note: All the AT commands terminate with carriage return(0x0D), we ignore it here.
About how to use AT commands, please refer to chapter 5.
We have one software for customers to use, customers can get it from our
http://www.usriot.com/Download/248.html.
website:http://www.usriot.com/Download/248.html.
And we have one software for customers to do serial and network tests, customers can get
http://www.usriot.com/Product/78.html
http://www.usriot.com/Product/78.html.
it from our website:http://www.usriot.com/Product/78.html
Jinan USR IOT Technology Limited
24 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
1. Setting
1) Set the destination phone number.
2) Set work mode as SMS message transmission.
2. Reset module, and send message to module via serial port, then you will get the
message on your cellphone. Then send a message back to module, then you will get
the message from module’s serial port.
Jinan USR IOT Technology Limited
25 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
Jinan USR IOT Technology Limited
26 / 55
www.usriot.com
tec@usr.cn
USR-GM3/GM3s User Manual
4.1.4.4.
www.usriot.com
SMS AT Command
Note: every command string should terminate with carriage return. Here we use [0D].
1. Query command password.
Besides, customers need to configure SMS message transmission, refer to chapter 4.1.4.3.
After setting successful, restart GM3. send “usr.cn#AT+VER” to GM3 from cellphone, then
then you will get response from GM3.
Jinan USR IOT Technology Limited
27 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
4.2. Register Package
Description
4.2.1.Description
4.2.1.
Under network transmission mode, customers can send Register Package, Register Package is
used to make server know what device is sending data, or as a password. Customers can
choose to send register package to network server, or serial device. Register Package could be
sent when network connection is established, or as the head of every TCP/UDP package. The
type of register package could be ICCID ,IMEI, or user-defined data.
4.2.2.
Usage
4.2.2.Usage
1. Enable sending register package.
2. Set the type of register package data. for instance, using user-defined data.
3. Set user-defined register data, for instance, set data as string “www.usr.cn”, you need to
convert it to hex string “7777772E7573722E636E”.
Jinan USR IOT Technology Limited
28 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
4. Set sending type, for instance, send data when connection is established.
Besides, customers need to configure socket A or socket B for network connection, refer to
chapter 4.1.2.3. After setting successful, restart GM3. When connection is establishing,
GM3 will send string “www.usr.cn” to server via socket A and socket B.
Jinan USR IOT Technology Limited
29 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
4.3. Heart Beat Package
Description
4.3.1.Description
4.3.1.
Under network transmission mode, customers can send Heart Beat Package to network server
or serial device.
Sending heart beat data to network server, is used to check if connection is alive. If GM3 sends
data unsuccessful for 3 times, it will try to reconnect to server.
Sending heart beat data to serial device , is usually used to query information from serial device
instead of sending query command from server, To do this can cut some communication flow.
4.3.2.
Usage
4.3.2.Usage
1. Enable sending heart beat package.
2. Set the destination of heart beat package data. for instance, to network server.
3. Set heart beat data, for instance, set data as string “www.usr.cn”, customer need to convert
it to hex string “7777772E7573722E636E”.
4. Set sending period, for instance, 30 seconds.
Jinan USR IOT Technology Limited
30 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
Besides, customers need to configure socket A or socket B for network connection, refer to
chapter 4.1.2.3. After setting successful, restart GM3. When connection is establishing, If
device is idle for 30 seconds, GM3 will send string “www.usr.cn” to server via socket A and
socket B.
4.4. UART
RS485
4.4.1.
4.4.1.RS485
4.4.1.1.
Description
GM3 module supports RS485 function. RS485 is half duplex, the direction of transmitting data
should be controlled manually. If customer enables module’s RS485 function, the pin 7 of
module is used to control the direction of communication.
Refer to command AT+UART
Jinan USR IOT Technology Limited
31 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
4.4.1.2. RS485 Reference Circuit
Similar RFC2217
4.4.2.
4.4.2.Similar
4.4.2.1.
Description
This function is similar to RFC2217. Customer can change the parameters of serial port
dynamically via network. This modification is temporary, when module restarts, the
parameters changed will return back to previous values.
4.4.2.2.
Definition of similar RFC2217
This protocol contains 8 bytes, details as the following form
Jinan USR IOT Technology Limited
32 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
Item
Head
Baud Rate
Bits Parameters
Check Sum
bytes
Refer to the
Sum of Baud Rate
following table
and Bits Parameters
interpretation
Exmaple1
(115200,N,8,1)
Exmaple2
(9600,N,8,1)
Fixed
MSB
data
55 AA 55
01 C2 00
83
46
55 AA 55
00 25 80
83
28
Interpretation of bits parameters
Bits
1:0
Interpretation
Data bits
Stop bits
Enable/disable parity
5:4
7:6
Parity type
No defined
Value
Description
00
Not Used
01
Not Used
10
11
disable
enable
00
ODD
01
EVEN
10
Not Used
11
Not Used
00
Not Used
5. Parameters Setting
Sending AT commands is the only way to set the parameters of GM3 module. There are two
kinds of commands, basic AT commands and extended AT commands.
Jinan USR IOT Technology Limited
33 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
Basic AT commands are used to setting the running parameters of GM3 under SMS
message transmission, network transmission and HTTPD modes.
Extended AT commands are used to design new functions by customers. About how to use
extended AT command, please refer to “GM3 extended AT commands User Guide”.
5.1. Operating AT command
When GM3 works in one of the three modes: SMS message transmission, network
transmission or HTTPD mode. You can get module into “command mode” by sending
specific timing data to it, then send commands to change module’s running parameters. If
changing is done, get module back to previous work mode.
Sending data to module
T1
T2
AT+ENTM
T5
T3
T7
TIME
T4
Sending data to device
T6
OK
+ok
In the above figure, abscissa axis means time, the data above time axis is sent to module
from device, and the data bellow time axis is sent to device from module.
time requirement:
T1 > 200ms
T2 < 50ms
T3 < 50ms
T5 < 3s
Go into command mode:
1.Module is in SMS message transmission, network transmission or HTTPD mode.
2.Device send “+++” to module, then module send ‘a’ to device.
Jinan USR IOT Technology Limited
34 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
3.If device receives ‘a’, it must send ‘a’ to module within 3 seconds.
4.Module receives ‘a’, and sends “+ok” to device.
5.Device receives “+ok”, it means module has gone to temporary command mode, so
device can send AT commands to module.
Back to previous mode:
1. Device send command “AT+ENTM” to module.
2. Module receives “AT+ENTM”, and send “OK” to device.
3. Device receives “OK”, it means module has gone back to previous mode.
5.2. AT Command Format
AT commands work in asking-answering mode, “asking” means device sends commands to
module, “answering” means module responds to device.
Symbol Description:
<>
content inside is necessary.
[]
content inside is not necessary.
{}
range, for example, A~B means the range is from A to B.
carriage return, hex number is 0D.
CMD
command code
OP
operator
PARA
parameter
CR
carriage return
LF
line feed
1) The format of asking
Command string: [CMD][OP][PARA]
Jinan USR IOT Technology Limited
35 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
Code
meaning
www.usriot.com
necessary
AT+
AT command head
Yes
CMD
purpose of command
Yes
OP
action type of command
No
PARA
parameters of command
No
CR
termination of command
Yes
Type of command
type
Command string
description
AT+{CMD}?{CR}
query parameters
AT+{CMD}=?{CR}
Query the value of parameter
AT+{CMD}{CR}
execute action or query parameters
AT+{CMD}={PARAM}{CR}
Set the value of parameter
2) The format of answering
There are two kinds of response, with or without echo.
All the followings are using without echo as examples.
Command string: [CR][LF][+CMD][OP][PARA][CR][LF][OK]
Code
meaning
necessary
CR
carriage return
No
LF
line feed
No
+CMD
response head
No
OP
operator
No
PARA
parameter
No
CR
carriage return
No
LF
line feed
No
CR
carriage return
Yes
LF
line feed
Yes
OK
operating successful
No
CR
carriage return
Yes
LF
line feed
Yes
type
Type of command
Command string
description
successful
<+CMD:>
return parameter
Jinan USR IOT Technology Limited
36 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
5.3. AT Command Set
NO.
command
description
Management commands
help message
restart
query and set enable/disable echo
ENTM
quit from command mode
WKMOD
query or set work mode
CALEN
query or set if allow to call
NATEN
query or set enable/disable network command
UATEN
query or set enable/disable serial port command
CMDPW
query or set command password
10
CACHEN
query or set enable/disable data cache
11
STMSG
query or set welcome message
Configuration commands
12
Save current settings
13
RELD
restore default settings
14
CLEAR
restore factory settings
15
CFGTF
save current setting as default setting
Query information commands
16
VER
query firmware version
17
SN
query SN code
18
ICCID
query CCID code
19
IMEI
query IMEI code
20
CNUM
query the MS ISDN related to the subscriber
UART parameters commands
21
UART
query or set serial port parameters
22
RFCEN
query or set enable/disable similar RFC2117
Socket parameters commands
23
APN
query or set APN code
24
SOCKA
query or set socket A parameters
25
SOCKB
query or set socket B parameters
26
SOCKAEN
query or set enable/disable socket A
27
SOCKBEN
query or set enable/disable socket B
28
SOCKASL
query or set socket A long or short connection
29
SOCKBSL
query or set socket B long or short connection
30
SOCKALK
query socket A connection status
31
SOCKBLK
query socket B connection status
Jinan USR IOT Technology Limited
37 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
Register package parameters commands
32
REGEN
query or set register package type
33
REGTP
query or set register package data type
34
REGID
query or set register ID（used for D2D）
35
REGDT
query or set register user-defined data
36
REGSND
query or set register package sending type
Heartbeat package parameters commands
37
HEARTEN
query or set enable/disable heartbeat
38
HEARTDT
query or set heartbeat data
39
HEARTTP
query or set heartbeat package sending type
40
HEARTTM
query or set heartbeat time
HTTPD parameters commands
41
HTPTP
query or set HTTP request type
42
HTPURL
query or set HTTP URL
43
HTPSV
query or set HTTP server address and port
44
HTPHD
query or set HTTP request head
SMS message parameters commands
45
DSTNUM
query or set destination phone number
46
SMSEND
send SMS message
1) AT+H
� function : help message.
� format :
� query :
AT+H{CR}
{CR}{LF}help message{CR}{LF}{CR}{LF}OK{CR}{LF}
� parameter :
� help message : commands introduction。
2) AT+Z
� function : restart。
� format :
AT+Z{CR}
{CR}{LF}OK{CR}{LF}
3) AT+E
� function : query and set enable/disable echo.
� format :
� Query parameter introductions :
Jinan USR IOT Technology Limited
38 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
AT+E=?{CR}
{CR}{LF}+E:<"on","off">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+E{CR} or AT+E?{CR}
{CR}{LF}+E:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+E=status{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� status : enable or disable echo
� “on” : enable
� “off” : disable
4) AT+ENTM
� function : quit from command mode.
� format :
� setting:
AT+ENTM{CR}
{CR}{LF}OK{CR}{LF}
5) AT+WKMOD
� function : query or set work mode.
� format :
� query parameter introductions:
AT+WKMOD=?{CR}
{CR}{LF}+WKMOD:<"CMD","SMS","NET","HTTPD">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+WKMOD{CR} or AT+WKMOD?{CR}
{CR}{LF}+WKMOD:mode{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+WKMOD=mode{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� mode : work mode
� “CMD” : AT command mode
� “SMS” : SMS message transmission mode
� “NET” : network transmission mode
� “HTTPD” : HTTPD mode
6)
AT+CALEN
Jinan USR IOT Technology Limited
39 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
� function : query or set if allow to call.
� format :
� query parameter introductions:
AT+CALEN=?{CR}
{CR}{LF}+CALEN:<"on","off">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+CALEN{CR} or AT+CALEN?{CR}
{CR}{LF}+CALEN:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+CALEN=status{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� status : enable or disable call
� “on” : enable
� “off” : disable
7) AT+NATEN
� function : query or set enable/disable network command.
� format :
� query parameter introductions:
AT+NATEN=?{CR}
{CR}{LF}+NATEN:<"on","off">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+NATEN{CR} or AT+NATEN?{CR}
{CR}{LF}+NATEN:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+NATEN=status{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� status : enable or disable network command
� “on” : enable
� “off” : disable
8) AT+UATEN
� function : query or set enable/disable serial port command
� format :
� query parameter introductions:
AT+UATEN=?{CR}
{CR}{LF}+UATEN:<"on","off">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+UATEN{CR} or AT+UATEN?{CR}
{CR}{LF}+UATEN:status{CR}{LF}{CR}{LF}OK{CR}{LF}
Jinan USR IOT Technology Limited
40 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
� set parameter:
AT+UATEN=status{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� status : enable or disable serial port command.
� “on” : enable
� “off” : disable
9) AT+CMDPW
� function : query or set command password
� format :
� query parameter introductions:
AT+CMDPW=?{CR}
{CR}{LF}+CMDPW:<"password">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+CMDPW{CR} or AT+CMDPW?{CR}
{CR}{LF}+CMDPW:password{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+CMDPW=password{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� password : command password
10) AT+CACHEN
� function : query or set enable/disable data cache.
� format :
� query parameter introductions:
AT+CACHEN=?{CR}
{CR}{LF}+CACHEN:<"on","off">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+CACHEN{CR} or AT+CACHEN?{CR}
{CR}{LF}+CACHEN:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+CACHEN=status{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� status : enable/disable data cache.
� “on” : enable
� “off” : disable
11) AT+STMSG
Jinan USR IOT Technology Limited
41 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
� function : query or set welcome message.
� format :
� query parameter introductions:
AT+STMSG=?{CR}
{CR}{LF}+STMSG:<"welcome message">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+STMSG{CR} or AT+STMSG?{CR}
{CR}{LF}+STMSG:message{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+STMSG=message{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� message : welcome message，when module powers up, it will show them, this can be
used to check if module starts up normally.
12) AT+S
� function : save current settings.
� format :
� setting:
S{CR}
AT+S
AT+
{CR}{LF}OK{CR}{LF}
13) AT+RELD
� function : restore default settings.
� format :
� setting:
AT+RELD{CR}
{CR}{LF}OK{CR}{LF}
14) AT+CLEAR
� function : restore factory settings.
� format :
� setting:
AT+CLEAR{CR}
{CR}{LF}OK{CR}{LF}
15) AT+CFGTF
� function : save current setting as default setting.
� format :
� setting:
Jinan USR IOT Technology Limited
42 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
AT+CFGTF{CR}
{CR}{LF}OK{CR}{LF}
16) AT+VER
� function : query version.
� format :
� query current value of parameter:
AT+VER{CR} or AT+VER?{CR}
{CR}{LF}+VER:version{CR}{LF}{CR}{LF}OK{CR}{LF}
� parameter :
� version : firmware version
17) AT+SN
� function : query SN code.
� format :
� query current value of parameter:
AT+SN{CR} or AT+SN?{CR}
{CR}{LF}+SN:code{CR}{LF}{CR}{LF}OK{CR}{LF}
� parameter :
� code : SN code
18) AT+ICCID
� function : query ICCID code.
� format :
� query current value of parameter:
AT+ICCID{CR} or AT+ICCID?{CR}
{CR}{LF}+ICCID:code{CR}{LF}{CR}{LF}OK{CR}{LF}
� parameter :
� code : ICCID code
19) AT+IMEI
� function : query IMEI code.
� format :
� query current value of parameter:
AT+IMEI{CR} or AT+IMEI?{CR}
{CR}{LF}+IMEI:code{CR}{LF}{CR}{LF}OK{CR}{LF}
� parameter :
� code : IMEI code
20) AT+CNUM
Jinan USR IOT Technology Limited
43 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
� function : query the MS ISDN related to the subscriber.
� format :
� query current value of parameter:
AT+CNUM{CR} or AT+CNUM?{CR}
{CR}{LF}+CNUM:phone number{CR}{LF}{CR}{LF}OK{CR}{LF}
� parameter :
� phone number : phone number
21) AT+UART
� function : query or set serial port parameters.
� format :
� query parameter introductions:
AT+UART=?{CR}
{CR}{LF}+UART:<2400,4800,9600,14400,19200,28800,33600,38400,57600,115200,
230400,460800,921600>,<"NONE","ODD","EVEN">,<7,8>,<1,2>,<"NONE","CRTS",
"RS485">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+UART{CR} or AT+UART?{CR}
{CR}{LF}+UART:baud,parity,data bit,stop bit,flow
control{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+UART=baud,parity,data bit,stop bit,flow control{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� baud : baud rate
2400,4800,9600,14400,19200,28800,33600,38400,57600,115200,230400,460800,921
600
� parity :
� “NONE” : no parity
� “ODD” : odd parity
� “EVEN” : even parity
� data bit :
� 7 : 7 data bits
� 8 : 8 data bits
� flow control :
� “NONE” : no flow control
� “CRTS” : use RTS/CTS for flow control
� “RS485” : use RS485 function
22) AT+RFCEN
� function : query or set enable/disable similar RFC2117.
� format :
Jinan USR IOT Technology Limited
44 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
� query parameter introductions:
AT+RFCEN=?{CR}
{CR}{LF}+RFCEN:<"on","off">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+RFCEN{CR} or AT+RFCEN?{CR}
{CR}{LF}+RFCEN:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+RFCEN=status{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� status : enable/disable similar RFC2117
� “on” : enable
� “off” : disable
23) AT+APN
� function : query or set APN code.
� format :
� query parameter introductions:
AT+APN=?{CR}
{CR}{LF}+APN:<"code">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+APN{CR} or AT+APN?{CR}
{CR}{LF}+APN:code{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+APN=code{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� code : APN code
24) AT+SOCKA
� function : query or set socket A parameters.
� format :
� query parameter introductions:
AT+SOCKA=?{CR}
{CR}{LF}+SOCKA:<"TCP","UDP">,<"address">,{CR}{LF}{CR}{LF}OK{CR}{
LF}
� query current value of parameter:
AT+SOCKA{CR} or AT+SOCKA?{CR}
{CR}{LF}+SOCKA:protocol,address,port{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+SOCKA=protocol,address,port{CR}
{CR}{LF}OK{CR}{LF}
Jinan USR IOT Technology Limited
45 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
� parameter :
� protocol : communication protocol
� “TCP” : TCP
� “UDP” : UDP
� address : server address, IP or domain name
� port : server port，1~65535
25) AT+SOCKB
� function : query or set socket B parameters.
� format :
� query parameter introductions:
AT+SOCKB=?{CR}
{CR}{LF}+SOCKB:<"TCP","UDP">,<"address">,{CR}{LF}{CR}{LF}OK{CR}{
LF}
� query current value of parameter:
AT+SOCKB{CR} or AT+SOCKB?{CR}
{CR}{LF}+SOCKB:protocol,address,port{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+SOCKB=protocol,address,port{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� protocol : communication protocol
� “TCP” : TCP
� “UDP” : UDP
� address : server address, IP or domain name
� port : server port，1~65535
26) AT+SOCKAEN
� function : query or set enable/disable socket A.
� format :
� query parameter introductions:
AT+SOCKAEN=?{CR}
{CR}{LF}+SOCKAEN:<"on","off">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+SOCKAEN{CR} or AT+SOCKAEN?{CR}
{CR}{LF}+SOCKAEN:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+SOCKAEN=status{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� status : enable or disable socket A
� “on” : enable
Jinan USR IOT Technology Limited
46 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
� “off” : disable
27) AT+SOCKBEN
� function : query or set enable/disable socket B.
� format :
� query parameter introductions:
AT+SOCKBEN=?{CR}
{CR}{LF}+SOCKBEN:<"on","off">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+SOCKBEN{CR} or AT+SOCKBEN?{CR}
{CR}{LF}+SOCKBEN:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+SOCKBEN=status{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� status : enable or disable socket B.
� “on” : enable
� “off” : disable
28) AT+SOCKASL
� function : query or set socket A long or short connection.
� format :
� query parameter introductions:
AT+SOCKASL=?{CR}
{CR}{LF}+SOCKASL:<"short","long">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+SOCKASL{CR} or AT+SOCKASL?{CR}
{CR}{LF}+SOCKASL:type{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+SOCKASL=type{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� type : connection style
� “short” : short connection
� “long” : long connection
29) AT+SOCKBSL
� function : query or set socket B long or short connection.
� format :
� query parameter introductions:
AT+SOCKBSL=?{CR}
Jinan USR IOT Technology Limited
47 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
{CR}{LF}+SOCKBSL:<"short","long">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+SOCKBSL{CR} or AT+SOCKBSL?{CR}
{CR}{LF}+SOCKBSL:type{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+SOCKBSL=type{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� type : connection style
� “short” : short connection
� “long” : long connection
30) AT+SOCKALK
� function : query socket A connection status.
� format :
� query current value of parameter:
AT+SOCKALK{CR} or AT+SOCKALK?{CR}
{CR}{LF}+SOCKALK:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� parameter :
� status : socket A connection status.
� “connected” : connected
� “disconnected” : disconnected
31) AT+SOCKBLK
� function : query socket B connection status.
� format :
� query current value of parameter:
AT+SOCKBLK{CR} or AT+SOCKBLK?{CR}
{CR}{LF}+SOCKBLK:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� parameter :
� status : socket B connection status.
� “connected” : connected
� “disconnected” : disconnected
32) AT+REGEN
� function : query or set enable/disable register package.
� format :
� query parameter introductions:
AT+REGEN=?{CR}
{CR}{LF}+REGEN:<"on","off">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
Jinan USR IOT Technology Limited
48 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
AT+REGEN{CR} or AT+REGEN?{CR}
{CR}{LF}+REGEN:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+REGEN=status{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� status : enable or disable register package
� “on” : enable
� “off” : disable
33) AT+REGTP
� function : query or set register package data type.
� format :
� query parameter introductions:
AT+REGTP=?{CR}
{CR}{LF}+REGTP:<"ICCID","IMEI","REGID","REGDT">{CR}{LF}{CR}{LF}OK{CR}{
LF}
� query current value of parameter:
AT+REGTP{CR} or AT+REGTP?{CR}
{CR}{LF}+REGTP:type{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+REGTP=type{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� type : type of register data
� “ICCID” : ICCID code
� “IMEI” : IMEI code
� “REGID” : register ID ( for D2D function )
� “REGDT” : user-defined data
34) AT+REGID
� function : query or set register ID(used for D2D).
� format :
� query parameter introductions:
AT+REGID=?{CR}
{CR}{LF}+REGID:{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+REGID{CR} or AT+REGID?{CR}
{CR}{LF}+REGID:id{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+REGID=id{CR}
{CR}{LF}OK{CR}{LF}
Jinan USR IOT Technology Limited
49 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
� parameter :
� id : register ID
35) AT+REGDT
� function : query or set register user-defined data.
� format :
� query parameter introductions:
AT+REGDT=?{CR}
{CR}{LF}+REGDT:{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+REGDT{CR} or AT+REGDT?{CR}
{CR}{LF}+REGDT:data{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+REGDT=data{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� data : user-defined register data, hex string, max length is 80 bytes,
for example, “7777772E7573722E636E” means “www.usr.cn” in ASCII.
36) AT+REGSND
� function : query or set register package sending type.
� format :
� query parameter introductions:
AT+REGSND=?{CR}
{CR}{LF}+REGSND:<"link","data","link&data">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+REGSND{CR} or AT+REGSND?{CR}
{CR}{LF}+REGSND:type{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+REGSND=type{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� type : sending type
� “link” : send register data when socket connects
� “data” : send register data as the head of every TCP/UDP package
� “link&data” : support both of above two ways
37) AT+HEARTEN
� function : query or set enable/disable heartbeat.
� format :
� query parameter introductions:
Jinan USR IOT Technology Limited
50 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
AT+HEARTEN=?{CR}
{CR}{LF}+HEARTEN:<"on","off">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+HEARTEN{CR} or AT+HEARTEN?{CR}
{CR}{LF}+HEARTEN:status{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+HEARTEN=status{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� status : enable/disable heartbeat function
� “on” : enable
� “off” : disable
38) AT+HEARTDT
� function : query or set heartbeat data.
� format :
� query parameter introductions:
AT+HEARTDT=?{CR}
{CR}{LF}+HEARTDT:<
{CR}{LF}+HEARTDT:<““data
data””>{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+HEARTDT{CR} or AT+HEARTDT?{CR}
{CR}{LF}+HEARTDT:data{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+HEARTDT=data{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� data : heartbeat data, hex string, max length is 80 bytes,
for example, “7777772E7573722E636E” means “www.usr.cn” in ASCII.
39) AT+HEARTTP
� function : query or set heartbeat package sending type.
� format :
� query parameter introductions:
AT+HEARTTP=?{CR}
{CR}{LF}+HEARTTP:<"COM","NET">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+HEARTTP{CR} or AT+HEARTTP?{CR}
{CR}{LF}+HEARTTP:type{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+HEARTTP=type{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
Jinan USR IOT Technology Limited
51 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
� type : sending type
� “COM” : send data to serial port
� “NET” : send data to network
40) AT+HEARTTM
� function : query or set heartbeat time.
� format :
� query parameter introductions:
AT+HEARTTM=?{CR}
{CR}{LF}+HEARTTM:<"time">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+HEARTTM{CR} or AT+HEARTTM?{CR}
{CR}{LF}+HEARTTM:time{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+HEARTTM=time{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� time : strobe period，unit is second
41) AT+HTPTP
� function : query or set HTTP request type.
� format :
� query parameter introductions:
AT+HTPTP=?{CR}
{CR}{LF}+HTPTP:<"GET","POST">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+HTPTP{CR} or AT+HTPTP?{CR}
{CR}{LF}+HTPTP:type{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+HTPTP=type{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� type : HTTP request type
� “GET” : get
� “POST” : post
42) AT+HTPURL
� function : query or set HTTP URL.
� format :
� query parameter introductions:
AT+HTPURL=?{CR}
Jinan USR IOT Technology Limited
52 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
{CR}{LF}+HTPURL:<"URL">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+HTPURL{CR} or AT+HTPURL?{CR}
{CR}{LF}+HTPURL:URL{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+HTPURL=URL{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� URL : HTTP request URL
43) AT+HTPSV
� function : query or set HTTP server address and port.
� format :
� query parameter introductions:
AT+HTPSV=?{CR}
{CR}{LF}+HTPSV:<"address">,{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+HTPSV{CR} or AT+HTPSV?{CR}
{CR}{LF}+HTPSV:address,port{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+HTPSV=address,port{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� address : server address，IP or domain name
� port : server port，1~65535
44) AT+HTPHD
� function : query or set HTTP request head.
� format :
� query parameter introductions:
AT+HTPHD=?{CR}
{CR}{LF}+HTPHD:<"head">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+HTPHD{CR} or AT+HTPHD?{CR}
{CR}{LF}+HTPHD:head{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+HTPHD=head{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� head : HTTP request head
Jinan USR IOT Technology Limited
53 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
www.usriot.com
45) AT+DSTNUM
� function : query or set destination phone number.
� format :
� query parameter introductions:
AT+DSTNUM=?{CR}
{CR}{LF}+DSTNUM:<"number">{CR}{LF}{CR}{LF}OK{CR}{LF}
� query current value of parameter:
AT+DSTNUM{CR} or AT+DSTNUM?{CR}
{CR}{LF}+DSTNUM:number{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+DSTNUM=number{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� number : destination phone number in “SMS” mode.
46) AT+SMSEND
� function : send SMS message.
� format :
� query parameter introductions:
AT+SMSEND=?{CR}
{CR}{LF}+SMSEND:<"number">,<1,2,3>,<"data">{CR}{LF}{CR}{LF}OK{CR}{LF}
� set parameter:
AT+SMSEND=number,type,data{CR}
{CR}{LF}OK{CR}{LF}
� parameter :
� number : destination phone number
� type: coding scheme
� 1 : ASCII coding，compressed
� 2 : 8 bits coding，not compressed
� 3 : UCS8 coding
� data : content of SMS message
Appendix A: Contact
-----------------------------------------------------------------------------------------------------------------------------Jinan USR IOT Technology Limited
54 / 55
tec@usr.cn
USR-GM3/GM3s User Manual
Company:
Address:
Tel:
Web:
Support :
Email:
www.usriot.com
Jinan USR IOT Technology Limited
Floor 11,Building1,No.1166 Xinluo Street,Gaoxin Distric,Jinan,Shandong,250101 China
86-531-55507297, 86-531-88826739
www.usr
iot
http://
http://www.usr
www.usriot
iot..com
http://h.usriot.com
sales@usr.cn
------------------------------------------------------------------------------------------------------------------------------
Appendix B: Disclaimer
This document provides information about USR-GM3/GM3s modules, this document does
not grant any license to intellectual property rights. Except the responsibility declared in the
product sale clause, USR does not assume any other responsibilities. In addition, USR
does not make any warranties for the sale and use of this product, including the suitability of
the product for a particular purpose, merchantability or fitness for any patent, copyright or
other intellectual property infringement, etc. USR may make changes to specifications and
product descriptions without notice.
Appendix C: Update History
2015-6-20
V1.0
basic version created
2015-6-20
V1.0.6 fix some errors, change reload pin function
2015-9-11
V1.0.7 increased use of setting software method
2015-10-12 V1.1.0 fix some errors, Added some instructions about GM3s
Jinan USR IOT Technology Limited
55 / 55
tec@usr.cn
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
tenna.
receiver is connected.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
FCC INFORMATION (additional)
OEM INTEGRATION INSTRUCTIONS:
This device is intended only for OEM integrators under the following conditions: The
module must be installed in the host equipment such that 20 cm is maintained between
the antenna and users, and the transmitter module may not be co-located with any other
transmitter or antenna. The module shall be only used with the internal antenna(s) that
has been originally tested and certified with this module. As long as 3 conditions above
are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements
required with this module installed (for example, digital device emissions, PC peripheral
requirements, etc.).
Validity of using the module certification:
In the event that these conditions cannot be met (for example certain laptop configurations
or co-location with another transmitter), then the FCC authorization for this module in
combination with the host equipment is no longer considered valid and the FCC ID of the
module cannot be used on the final product. In these circumstances, the OEM integrator
will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End product labeling:
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains FCC ID:
2AJDA-USRGM3”.
Information that must be placed in the end user manual:
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user's manual of the end product which
integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.
This device must be kept away from all persons by 20cm or more and installations using
less distance, or installations using antennas with gain greater than that with which this
was Certified will require additional approvals.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Create Date : 2016:06:07 16:04:27+08:00 Modify Date : 2016:10:09 17:50:13+08:00 Metadata Date : 2016:10:09 17:50:13+08:00 Producer : PDFdo.com 5.5.6.0 Format : application/pdf Document ID : uuid:9edd814c-b85f-4303-9cd2-67ea6b9c4870 Instance ID : uuid:cb0fbf44-f607-419e-b115-60e0cdb22808 Page Count : 57EXIF Metadata provided by EXIF.tools