Shark Steam Mop S3101 Quick Start Manual

Sharp-S3101-Quick-Start-Manual-804814 sharp-s3101-quick-start-manual-804814

: Shark Shark-Shark-Steam-Mop-S3101-Quick-Start-Manual-678913 shark-shark-steam-mop-s3101-quick-start-manual-678913 shark pdf

Open the PDF directly: View PDF .
Page Count: 1

Download
Open PDF In Browser	View PDF

STEAM MOP ASSEMBLY

	

USING YOUR STEAM MOP

2	 Place the cleaning pad on the 	
mop head and press down.  

NOTE: Prime the unit by pumping the handle to release moisture into the pad before use.

STEPS TO A SHARK® CLEAN FLOOR

S3101_N3_QSG_131223

	

1	 SWEEP OR VACUUM YOUR FLOOR	

4

2

Thank you for choosing a

	

We recommend the use of the Shark® Vacuum and/or Sweeper to work
in conjunction with the steam mop for a complete cleaning system.

cord release

Shark Steam Mop!
®

	

2	 SANITIZE WITH A SHARK® STEAM MOP**	
	

Shark® Steam Mops provide 99.9% sanitization* and are great for
cleaning up stuck on dirt, grime, and footprints.

•	99.9% Sanitization* with just water
	

•	Lightweight Powerful Cleaning Performance

1

For extra tough messes, try our new Shark® Steam Energized™ cleanser.
This gentle cleaning solution combines with steam for superior deep
cleaning.

	

3	 REGULAR MAINTENANCE IS KEY	
	

•	Disposable SaniFiber™ Pads are great for quick clean
ups and germy messes

Daily spot cleaning is recommended to keep dirt and grime from
building up in your home.
	

	

1	 Insert the extension
tubes into each other.

•	Washable MicroFiber Pads for long lasting cleaning
performance

The range of convenient, quick clean products from Shark® is
guaranteed to help you keep a clean and sanitized home.

3
	

4	 Plug in the mop and wait 30
second for the unit to heat up.
The push/pull motion releases
the steam as you mop. Steam
output is adjusted by the speed
of your moping motion.

	

3	 Open the water tank cap, use the
filling flask to fill the tank with water,
then replace & tighten the cap.

** TIP: The initial use of the steam mop may cause streaking or clouding due to
the residue from chemicals and polish previously used on your floors. Regular
use of the steam mop will diminish this effect. For stubborn cases, you may
need to rinse the floor with a mixture of one part vinegar and two parts
water. Remember, a clean mop pad is essential for residue removal.

* Under controlled test conditions, results may vary.

For brighter, streak free floors, try

Problem Resolution Checklist

P
P
P
P
P
P

Issue

Resolution

The Shark® Steam Mop will not turn-on.

Ensure the power cord is plugged in correctly to a working 120 volt outlet.

Shark® Steam Mop will not make steam.

Check the water tank. If empty, add water to the steam mop by following the instructions above.

Shark® Steam Mop leaves water on the floor or is
hard to push.

Be sure that the cleaning pad is soaked through and properly affixed to the entire mop head. If the
pad is over saturated, unplug the unit, wait 2 to 3 minutes for the pad to cool, and then replace with
a clean dry mop pad.

Shark® Steam Mop left white spot on the floor.

Check to see if the cleaning pad is soaked through. We recommend that you unplug the unit and
replace the cleaning pad. Make sure that the cleaning pad is attached correctly.

Floors are cloudy, streaky or spotty after steaming.

The initial use of the Steam Mop may cause clouding, streaking, or spotting of floors due to the
residue from chemicals previously used to treat the floor. Be sure to follow the “Steps to a Shark®
Clean Floor”.

Unable to Resolve Your Issue?

ENERGIZED
cleanser
• Breaks down tough
greasy & stuck on messes
• Non-toxic, biodegradable
• Safe around kids & pets†
• Great fresh scent

If you are still having difficulty using the Shark® Steam Mop, call our Customer Care Center at 1-800798-7398.

Cleanser available at select retailers and at

www.sharkclean.com  
or by calling
Looking for Replacement Parts or Accessories? Check out www.sharkclean.com or give our Customer Care Center a call at 1-800-798-7398.

†

When used as directed.

1-800-798-7398

Steam Mop
GETTING
STARTED

Paper: Quality A (Bright White) 157g/m2
Coating: Matte both sides



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2013:12:23 16:09:49-05:00
Metadata Date                   : 2013:12:23 16:10:13-05:00
Modify Date                     : 2013:12:23 16:10:13-05:00
Creator Tool                    : Adobe InDesign CS6 (Macintosh)
Instance ID                     : uuid:29645a20-df79-4e4f-a2fa-f1a7874ecb27
Original Document ID            : xmp.did:01801174072068118CD2B2043B525988
Document ID                     : xmp.id:9612B6963C206811822AB3A9FC85CF85
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:9512B6963C206811822AB3A9FC85CF85
Derived From Document ID        : xmp.did:9688E7B4E22068118083E8042E70E59B
Derived From Original Document ID: xmp.did:01801174072068118CD2B2043B525988
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Macintosh)
History Changed                 : /
History When                    : 2013:12:23 16:09:49-05:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 1
Creator                         : Adobe InDesign CS6 (Macintosh)

EXIF Metadata provided by EXIF.tools