Sharp AR 5316 5316/5320/5316X/5320X Operation Manual GB User To The 28297029 Bea9 4f76 8e91 E8c59bbe5ac6

User Manual: Sharp AR-5316 to the manual

Open the PDF directly: View PDF .
Page Count: 72

MODEL

AR-5316

AR-5320

AR-5316 X

AR-5320 X

DIGITAL MULTIFUNCTIONAL

SYSTEM

OPERATION MANUAL

•BEFORE USING

THE MACHINE

•COPY FUNCTIONS

•PRINTER FUNCTIONS

•USER SETTINGS

•TROUBLESHOOTING

•ROUTINE MAINTENANCE

•PERIPHERAL DEVICES

AND SUPPLIES

•APPENDIX

Page

AR-5316/AR-5316 X

AR-5320/AR-5320 X

HINA

➀

QSZZ

AR-5316-5320-EX.book 1 ページ２００３年１１月２６日　水曜日　午後５時３分

The CE mark logo label is affixed on an equipment in case that the directives described in the

above sentence are applicable to the product. (This sentence is not applicable in any country

where the above directives are not required.)

Warning

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

In some areas, the "POWER" switch positions are marked "I" and " " on the copier

instead of "ON" and "OFF".

If your copier is so marked, please read "I" for "ON" and " " for "OFF".

Caution!

For a complete electrical disconnection, pull out the main plug.

The socket-outlet shall be installed near the equipment and shall be easily

accessible.

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by

93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung

93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la

directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla

direttiva 93/68/EEC.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida

pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de

la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras av

93/68/EEC.

Dette produktet oppfyller betingelsene i derektivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä

93/68/EEC.

Do not make copies of anything which is prohibited from copying by law. The

following items are normally prohibited from copying by national law. Other

items may be prohibited by local law.

● Checks ● Passports ● Driver's licenses

● Money ● Stamps ● Bonds ● Stocks ● Bank drafts

AR-5316-5320-EX.book 1 ページ２００３年１１月２６日　水曜日　午後５時３分

CONTENTS

CAUTIONS................................................................................................................................................. 3

●CAUTIONS ON USING..................................................................................................................................... 3

●IMPORTANT POINTS WHEN SELECTING AN INSTALLATION SITE ........................................................... 3

●CAUTIONS ON HANDLING ............................................................................................................................. 4

●CAUTIONS ON LASER .................................................................................................................................... 4

●ENVIRONMENTAL INFORMATION................................................................................................................. 4

USING THE MANUAL ............................................................................................................................... 5

●ABOUT THE OPERATION MANUALS............................................................................................................. 5

●THE MEANING OF "R" IN ORIGINAL AND PAPER SIZE INDICATIONS ....................................................... 5

●CONVENTIONS USED IN THIS MANUAL....................................................................................................... 5

●SPF ................................................................................................................................................................... 5

●DIFFERENCES BETWEEN MODELS.............................................................................................................. 6

MAIN FEATURES ...................................................................................................................................... 7

1BEFORE USING THE MACHINE

PART NAMES AND FUNCTIONS ..................... 8

●OPERATION PANEL ......................................10

POWER ON AND OFF..................................... 12

●POWER ON ....................................................12

●POWER OFF ..................................................12

LOADING PAPER............................................ 13

●PAPER............................................................13

●LOADING PAPER...........................................14

●CHANGING A TRAY’S PAPER SIZE

SETTING ........................................................16

2COPY FUNCTIONS

NORMAL COPYING ........................................ 18

●MAKING A COPY DARKER OR LIGHTER ....21

●SELECTING THE TRAY.................................21

●SETTING THE NUMBER OF COPIES ...........22

REDUCTION/ENLARGEMENT/ZOOM............ 22

●AUTOMATIC RATIO SELECTION .................22

●MANUAL RATIO SELECTION........................23

●

SELECTING THE VERTICAL AND HORIZONTAL

COPY RATIOS SEPARATELY

............................24

TWO-SIDED COPYING USING THE BYPASS

TRAY................................................................ 26

DUAL PAGE COPYING................................... 27

INTERRUPTING A COPY RUN ....................... 28

3PRINTER FUNCTIONS

USING THE PRINTER MODE ......................... 29

●BASIC PROCEDURE FOR PRINTING.......... 29

●

OPERATION IN COPY AND PRINTER MODES

.... 30

4USER SETTINGS

ADJUSTING THE AUTOMATIC EXPOSURE

LEVEL.............................................................. 31

TONER SAVE MODE AND HIGH IMAGE

QUALITY MODE.............................................. 32

CUSTOMISING SETTINGS ............................. 33

●USER PROGRAMS ....................................... 33

●SELECTING A SETTING FOR A USER

PROGRAM .................................................... 35

SETTINGS FOR AUDITING MODE................. 36

●AUDITING MODE .......................................... 36

●AUDITING MODE SETTINGS ....................... 36

●

SELECTING AUDITING MODE SETTINGS

..... 37

5TROUBLESHOOTING

TROUBLESHOOTING..................................... 40

●MACHINE/COPYING PROBLEMS ................ 41

●PRINTING PROBLEMS................................. 44

INDICATORS AND DISPLAY MESSAGES .... 46

MISFEED REMOVAL ...................................... 47

●MISFEED IN THE SPF .................................. 47

●MISFEED IN THE BYPASS TRAY ................ 48

●MISFEED IN THE MACHINE......................... 49

●MISFEED IN THE UPPER PAPER TRAY ..... 52

●MISFEED IN THE LOWER PAPER TRAY .... 53

REPLACING THE TONER CARTRIDGE ........ 54

AR-5316-5320-EX.book 1 ページ２００３年１１月２６日　水曜日　午後５時３分

6ROUTINE MAINTENANCE

CHECKING THE TOTAL OUTPUT COUNT

AND TONER LEVEL........................................ 55

●CHECKING THE TOTAL OUTPUT COUNT...55

●CHECKING THE TONER LEVEL ...................56

ROUTINE MAINTENANCE.............................. 56

●CLEANING THE DOCUMENT GLASS AND

SPF/DOCUMENT COVER .............................56

●CLEANING THE BYPASS TRAY PAPER

FEED ROLLER ...............................................57

●CLEANING THE TRANSFER CHARGER ......57

PERIPHERAL DEVICES AND SUPPLIES

PERIPHERAL DEVICES.................................. 58

●SINGLE PASS FEEDER.................................58

STORAGE OF SUPPLIES ............................... 59

●PROPER STORAGE ......................................59

8APPENDIX

SPECIFICATIONS ........................................... 60

SOFTWARE LICENSE .................................... 62

INDEX............................................................... 64

AR-5316-5320-EX.book 2 ページ２００３年１１月２６日　水曜日　午後５時３分

CAUTIONS

Follow the cautions below when using this machine.

CAUTIONS ON USING

Warning:

• The fusing area is hot. Exercise care in this area when removing misfed paper.

• Do not look directly at the light source. Doing so may damage your eyes.

Caution:

• Do not switch the machine rapidly on and off. After turning the machine off, wait 10 to 15 seconds before turning it

back on.

• Machine power must be turned off before installing any supplies.

• Place the machine on a firm, level surface.

• Do not install the machine in a humid or dusty location.

• When the machine is not used for a long time, for example, during prolonged holidays, turn the power switch off

and remove the power cord from the outlet.

• When moving the machine, be sure to turn the power switch off and remove the power cord from the outlet.

• Do not cover the machine with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat

dissipation, damaging the machine.

• Use of controls or adjustments or performance of procedures other than those specified herein may result in

hazardous laser radiation exposure.

• The socket-outlet should be installed near the machine and should be easily accessible.

IMPORTANT POINTS WHEN SELECTING AN

INSTALLATION SITE

Improper installation may damage the machine. Please note the following during initial installation and whenever the

machine is moved.

Do not install your machine in areas that are:

If the machine is moved from a cool place to a warm place, condensation may form inside the machine. Operation

in this condition will cause poor copy quality and malfunctions. Leave the machine at room temperature for at least

2 hours before use.

•damp, humid, or very

dusty

•exposed to direct sunlight

•poorly

ventilated

•subject to extreme

temperature or humidity

changes, e.g., near an

air conditioner or

heater.

Caution

AR-5316-5320-EX.book 3 ページ２００３年１１月２６日　水曜日　午後５時３分

The machine should be installed near an accessible power outlet for easy connection and

disconnection.

Be sure to connect the power cord only to a power outlet that meets the specified voltage and

current requirements. Also make certain the outlet is properly grounded.

Be sure to allow the required space around the machine

for servicing and proper ventilation.

CAUTIONS ON HANDLING

Be careful in handling the machine as follows to maintain the performance of this machine.

Do not drop the machine, subject it to shock or strike it against any object.

Store spare toner cartridges in a cool dry place without removing from the package before use.

• If they are exposed to direct sunlight or excessive heat, poor copies may result.

Do not touch the photoconductive drum (green portion).

• Scratches or smudges on the drum will cause dirty copies.

CAUTIONS ON LASER

Trademark acknowledgements

•Microsoft

® Windows® operating system is a trademark or copyright of Microsoft Corporation in the U.S.A. and

other countries.

•

Windows

95, Windows

98, Windows

Me, Windows NT

4.0, Windows

2000, and Windows

XP are trademarks

or copyrights of Microsoft Corporation in the U.S.A. and other countries.

• IBM and PC/AT are trademarks of International Business Machines Corporation.

•

Acrobat

Reader Copyright

Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated.

• All other trademarks and copyrights are the property of their respective owners.

ENVIRONMENTAL INFORMATION

Connect the machine to a power outlet which is not used for other electric appliances. If a lighting fixture is

connected to the same outlet, the light may flicker.

Wave length 785 nm + 10 nm/- 15 nm

Pulse times (8.141 µs ± 0.1 µs)/7 mm

Output power 0.14 mW – 0.22 mW

As an ENERGY STAR® Partner, SHARP has determined that this product meets

the ENERGY STAR® guidelines for energy efficiency.

Note

20 cm (8")

20 cm

(8")

20 cm

(8")

AR-5316-5320-EX.book 4 ページ２００３年１１月２６日　水曜日　午後５時３分

USING THE MANUAL

This machine has been designed to provide convenient copying features in a minimum amount of office space and

with maximum operational ease. To get full use of all machine features, be sure to familiarise yourself with this

manual and the machine. For quick reference during machine use, keep this manual in a handy location.

ABOUT THE OPERATION MANUALS

The operation manuals for the machine are as follows:

Operation Manual (Digital Multifunctional System) (this manual)

This manual contains explanations of the product and procedures for using the machine as a copier.

Online Manual (on the accessory CD-ROM)

This manual explains the procedures for using the machine as a printer.

Software Setup Guide (separate manual)

This manual contains instructions for installing the software that allows the machine to be used with your computer

and procedures for establishing initial printer settings.

THE MEANING OF "R" IN ORIGINAL AND PAPER SIZE

INDICATIONS

An "R" appearing at the end of an original or paper size (A4R (5-1/2" x 8-1/2"R, 8-1/2" x 11"R), etc.) indicates that the

original or paper is oriented horizontally as shown below.

Sizes that can be placed only in the horizontal (landscape) orientation (B4, A3 (8-1/2" x 14", 11" x 17")) do not

contain the "R" in their size indication.

CONVENTIONS USED IN THIS MANUAL

SPF

This operation manual refers to the Single Pass Feeder as the "SPF".

Warns the user that injury may result if the contents of the warning are not properly followed.

Cautions the user that damage to the machine or one of its components may result if the contents

of the caution are not properly followed.

Notes provide information relevant to the machine regarding specifications, functions,

performance, operation and such, that may be useful to the user.

Warning

Caution

Note

AR-5316-5320-EX.book 5 ページ２００３年１１月２６日　水曜日　午後５時３分

DIFFERENCES BETWEEN MODELS

This manual covers the following models.

AB series (metric) and inch series references

Both specifications are quoted where applicable.

For example:

Page 15, step 1 ....................B4 and A3 (8-1/2" x 14" and 11" x 17")

Page 60................................50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%,

200% (50%, 64%, 77%, 95%, 100%, 121%, 129%,

141%, 200%)

Although AB series size indications are shown on the operation panel of this manual, inch series indications are

displayed on the inch series machines.

Model AR-5320/AR-5320 X AR-5316/AR-5316 X

Appearance

(With optional SPF installed) (With optional SPF installed)

Copy speed 20CPM 16CPM

Paper trays Two (250 x 2) One (250 x 1)

The above illustration is used in

instances where a function and/

or the operation of the machine

is the same on both models.

EXTRA

8½

5½

EXTRA

[Inch series][AB series]

AR-5316-5320-EX.book 6 ページ２００３年１１月２６日　水曜日　午後５時３分

MAIN FEATURES

High-speed laser copying

•First-copy time*1 at 300 dpi*2 is only 7.2 seconds .

•Copying speed is 20/16 copies per minute. This is ideal for business use and provides a big boost to workplace

productivity.

*1First-Copy time may vary depending on the power-supply voltage, ambient temperature, and other operating conditions.

*2"dpi" ("dots per inch") is unit that is used to measure resolution. Resolution indicates how much detail can be reproduced in

a printed or scanned image.

High-quality digital image

•High-quality copying at 600 dpi is performed.

•In addition to automatic exposure adjustment, two original modes can be selected: "TEXT" for text-only originals,

and "PHOTO" for photographs. The exposure can be adjusted to five levels in each mode.

•The photo mode copying function allows clear copying of delicate halftone original images such as monochrome

photos and colour photos.

Enhanced copying features

•Zoom copies can be made from 25% to 400% in 1% increments.

(When the SPF is being used, the zoom copy ratio range is 50% to 200%.)

•Continuous copying of up to 999 copies is possible. (Can be changed to a maximum of 99 copies in the user

programs.)

•The user programs allow customised machine settings and management. Access to the machine can be

controlled by enabling audit mode.

Scan once/Print many

•The machine is equipped with a memory buffer allowing the machine to scan an original once and make up to 999

copies of the scanned image. This improves workflow, reduces operating noise from the machine and reduces

wear and tear on the scanning mechanism, which provides for a higher reliability.

Laser printer function

•The accompanying printer driver can be installed to enable use of the machine as a printer. (See the

accompanying Software Setup Guide.)

Environment and people friendly design

•Preheat and auto power shut-off modes are provided to reduce power consumption when the machine is not in

use.

•A universal design has been implemented in the product whereby the height of the operation panel and shape of

the keys are designed to be usable by as many people as possible.

AR-5316-5320-EX.book 7 ページ２００３年１１月２６日　水曜日　午後５時３分

1Chapter 1

BEFORE USING THE MACHINE

This chapter contains basic information that should be read before using the machine.

PART NAMES AND FUNCTIONS

Document feeder cover (when the SPF is installed)

/document cover

Open to make copies from the document glass.

(p.18)

Document glass

Place an original that you wish to scan face down

here. (p.18)

Handles

Use to move the machine.

Power switch

Press to turn the machine power on and off. (p.12)

Operation panel

Contains operation keys and indicator lights. (p.10)

Paper output tray

Copies and prints are deposited to this tray.

Front cover

Open to remove paper misfeeds and perform

machine maintenance. (p.50, p.54)

Paper trays

Each tray holds 250 sheets of paper. (p.14)

Side cover

Open to remove paper misfeeds and perform

machine maintenance.

(p.48, p.57)

Side cover handle

Pull to open the side cover. (p.48)

Bypass tray guides

Adjust to the width of the paper. (p.15)

Bypass tray

Paper including special paper (such as transparency

film) can be fed from the bypass tray. (p.15

p.26)

Bypass tray extension

Pull out when feeding large paper such as B4 and

A3 (8-1/2" x 14" and 11" x 17"). (p.15)

Charger cleaner

Use to clean the transfer charger. (p.57)

USB 1.1 connector

Connect to your computer to use the printer

functions. (Software Setup Guide)

12 13

AR-5316-5320-EX.book 8 ページ２００３年１１月２６日　水曜日　午後５時３分

BEFORE USING THE MACHINE

Parallel connector

Connect to your computer to use the printer

function. (Software Setup Guide)

Document feeder tray (when the SPF is

installed)

Place the original(s) that you wish to scan face up

here. Holds up to 40 originals.

Original guides (when the SPF is installed)

Adjust to the size of the originals.

Feeding roller cover (when the SPF is installed)

Open to remove misfed originals. (p.47)

Right side cover (when the SPF is installed)

Open to remove misfed originals. (p.47)

Exit area (when the SPF is installed)

Originals exit the machine here after copying.

Toner cartridge lock release lever

To replace the toner cartridge, pull out the toner

cartridge while pushing on this lever.

Toner cartridge

Contains toner. (p.54)

Roller rotating knob

Turn to remove misfed paper. (p.49, p.50)

Fusing unit release levers

To remove a paper misfeed from the fusing unit, push

down on these levers and remove the paper. (p.50)

Photoconductive drum

Copy images are formed on the photoconductive

drum.

Fusing unit paper guide

Open to remove misfed paper.

1917

24 25

2726

The fusing unit is hot. Do not touch

the fusing unit when removing misfed

paper. Doing so may cause a burn or

injury.

The model name can be seen on the machines

front cover.

Warning

Note

AR-5316-5320-EX.book 9 ページ２００３年１１月２６日　水曜日　午後５時３分

BEFORE USING THE MACHINE

OPERATION PANEL

ON LINE key ( ) / indicator

Press to toggle the machine between online and

off-line. The indicator lights up when the machine

is online, and goes off when the machine is

off-line. The indicator blinks while the machine is

receiving print data and while printing is paused.

(p.29)

DUAL PAGE COPY key ( ) / indicator

Use to make individual copies of the two pages of

an open book or other two-page original. (p.27)

XY-ZOOM key ( ) / indicator

Press to change the horizontal and vertical copy

ratios independently. (p.24)

AUTO/TEXT/PHOTO key ( / / ) /

indicators

Use to select the exposure mode:

"AUTO", "TEXT", or "PHOTO". (p.21)

AUDIT CLEAR key ( )

Closes an open account. (p.39)

AUTO PAPER SELECT indicator ( )

Paper of the proper size will be automatically

selected depending on the original size and

selected copy ratio when this indicator is on. (p.20)

Alarm indicators

[ ] Maintenance indicator (p.46)

[ ] Toner cartridge replacement required

indicator (p.46)

[ ] Developer replacement required indicator

(p.46)

[ ] Paper required indicator (p.46)

[ ] Misfeed indicator (p.46)

POWER SAVE indicator ( )

Lights up when the machine is in a power save mode.

(p.12)

Display

Shows the set number of copies, as well as the copy

ratio, user program function or setting code, or an

error code when an error occurs.

Copy ratio display key ( )

Hold down when the machine is not in use to

display the copy ratio in the display. (p.24)

ZOOM indicator

Lights up when a zoom ratio is set. (p.24)

Zoom keys ( , )

Use to select any reduction or enlargement copy ratio

from 25% to 400% in increments of 1%. (p.24)

INTERRUPT key ( ) / indicator

Interrupts a copy run. (p.28)

Light and Dark keys ( , ) / indicators

Use to adjust the TEXT or PHOTO exposure level.

(p.21)

ORIGINAL SIZE ENTER key ( ) / ORIGINAL

SIZE indicators

Use to enter the original size. (p.16) The selected

original size will light up.

AUTO

5ACC.#-C

AUTO

ENTER

The example of a display of inch series

200

141

129

121

8½

5½

EXTRA

8½

100

AR-5316/

AR-5316 X

18 21

The indications of the operation panel may differ

depending on the country and the region.

18 21 22

15 16

AR-5316-5320-EX.book 10 ページ２００３年１１月２６日　水曜日　午後５時３分

BEFORE USING THE MACHINE

PAPER SIZE indicators

Light up to show the selected copy paper size. (p.16)

PAPER SIZE ENTER key ( )

Use to set the paper size in the paper trays. (p.16)

SPF indicator (when the SPF is installed)

Lights up when originals are set in the document

feeder tray. (p.19)

TRAY SELECT key ( )

Use to manually select a paper tray. (p.21)

AUTO IMAGE key ( ) / indicator

Press for automatic copy ratio selection. (p.22)

Paper feed location / misfeed location

indicators

The selected paper feed location is shown by a lit

indicator ( ). (p.18)

The general location of misfed paper is shown by a

blinking red indicator ( ). (p.47)

PRESET RATIO selector keys ( , )

/ indicators

Use to select preset reduction/enlargement copy

ratios. (p.23)

Numeric keys

Use to select the desired copy quantity or to make

user program entries. (p.22)

To display the total number of pages output by the

machine, hold the [0] key down. (p.55)

[] key

Use to check the total number of copies made.

(p.55)

START key ( ) /indicator

Press to make a copy (p.18). Also press to exit

"Auto power shut-off" mode and to set a user

program. Copying is possible when the indicator is

on.

CLEAR ALL key ( )

Clears all selected settings and returns the

machine to the initial settings. (p.12)

CLEAR key ( )

Clears the copy quantity display or terminates a

copy run.

AUTO %

INTERRUPT

ZOOM

135

25 400%

AUTO

ENTER

AUTO

ACC.#-C

AUTO %

EXTRA

200

141

122

115

100

(Two-tray model only)

Not used for this machine.

7 8 9

10 11 12

14 15 16 17 18 19 20 21 22 23 24 25 26 27

AR-5316-5320-EX.book 11 ページ２００３年１１月２６日　水曜日　午後５時３分

POWER ON AND OFF

The power switch is located on the left side of the machine.

POWER ON

Turn the power switch to the "ON"

position.

It will take about 45

seconds for the machine

to warm up. While the

machine is warming up,

the POWER SAVE

indicator ( ) will blink.

(The POWER SAVE

indicator ( ) will go off

when the machine is

ready to copy.)

However, you can make desired settings and press

the [START] key ( ) during warm-up. Copying will

start after warm-up.

POWER OFF

Make sure that the machine is not in

operation and then turn the power switch

to the "OFF" position.

If the power switch is

turned off while the

machine is in operation,

a misfeed may occur and

the job that was in

progress will be

cancelled.

Check the following to make sure the machine is not in

operation:

•The START indicator is lit. (Initial state)

•The POWER SAVE indicator ( ) is lit. ("Preheat

mode" or "Auto power shut-off" mode)

Power Save Modes

Preheat mode

This function automatically switches the machine to a low power consumption state if the set duration of time

elapses without the machine being used when the power is on. The POWER SAVE indicator ( ) lights up,

however, the keys on the operation panel can be used. Normal operation automatically resumes when a key on the

operation panel is pressed, an original is placed, or a print job is received.

Auto power shut-off mode

This function automatically switches the machine to a state that consumes even less power than preheat mode if the

set duration of time elapses without the machine being used when the power is on. All lights except the POWER

SAVE indicator ( ) and ON LINE indicator ( ) go off. To resume normal operation, press the [START] key ( ).

Normal operation also resumes automatically when a print job is received. While in auto power shut-off mode, no

keys (except the [START] key ( )) can be used.

•The machine reverts to the initial settings when it is first turned on, when the [CLEAR ALL] key ( ) is pressed,

or when no keys are pressed for the preset "Auto clear" time following the end of a copy job. When the machine

reverts to the initial settings, all settings and functions selected to that point are cancelled. The "Auto clear" time

can be changed in the user settings. (p.33)

•The machine is initially set to automatically enter power save mode if not used for copying or printing, for a

preset period of time. This setting can be changed in the user programs. (p.33)

The machine has two power save modes to reduce overall power consumption thereby

reducing the cost of operation. In addition, these modes conserve natural resources and help

reduce environmental pollution. The two power save modes are "Preheat mode" and "Auto

power shut-off mode".

The preheat activation time and the "Auto power shut-off timer" can be changed using user programs. It is

suggested that you set times that are appropriate for your usage of the machine. (p.33)

Note

Initial settings

The machine assumes the initial settings when it is first turned on, when the [CLEAR ALL] key ( ) is pressed,

and approximately one minute after the last copy is made in any mode.

Copy ratio: 100%, Exposure: Automatic

Copy quantity: 0, All special copier modes: Off

Auto paper selection

: On,

Paper feed station

: The tray selected in the "Default tray setting" in the user programs. (p.34)

AR-5316-5320-EX.book 12 ページ２００３年１１月２６日　水曜日　午後５時３分

LOADING PAPER

The paper required indicator ( ) will light up when there is no copy paper in the selected paper feed tray, or when

the selected paper tray is not installed or is improperly installed.

PAPER

For best results, use only SHARP recommended paper.

*1A5 (5-1/2" x 8-1/2") can be used in the upper paper tray but cannot be used in other trays.

*2When making a large number of copies or prints using 90 g/m2 (24 lbs.) paper, remove the output from the paper output tray

when about 100 pages have been printed. The output may not stack correctly if more than 100 pages are allowed to

accumulate.

*3The number of sheets of the paper which can be set changes with the weight of a paper.

Special papers

Follow these guidelines when using special papers.

●

●●

●Use SHARP recommended transparency film and label sheets. Using other than SHARP recommended

paper may result in misfeeds or smudges on the output. If other than SHARP recommended media must

be used, feed each sheet one at a time using the bypass tray (do not attempt continuous copying or

printing).

●

●●

●There are many varieties of special paper available on the market, and some cannot be used with this

machine. Before using special paper, contact your authorised service representative.

●

●●

●Before using other than SHARP recommended paper, make a test copy to see if the paper is suitable.

Paper tray type Paper type Size Weight Capacity

Paper tray Standard paper

Recycled paper

A5*1

(5-1/2" x 8-1/2"*1 (Invoice))

(8-1/2" x 11" (Letter))

(8-1/2" x 13" (Foolscap))

(8-1/2" x 14" (Legal))

(11" x 17" (Ledger))

56 g/m2 to 90 g/m2 *2

(15 lbs. to 24 lbs. *2)

250 sheets

(Load paper lower

than the line on the

tray)

Bypass tray Standard paper

Recycled paper

A6R to A3

(5-1/2" x 8-1/2" (Invoice)

to 11" x 17" (Ledger))

56 g/m2 to 80 g/m2

(15 lbs. to 20 lbs.)

100 sheets *3

Thick paper Max. 200 g/m2 (54

lbs.)

Load one sheet of

these papers at a

time to the bypass

tray.

Transparency film

Labels

Envelopes International DL

(110 mm x 220 mm)

International C5

(162 mm x 229 mm)

Commercial 9

(3-7/8" x 8-7/8")

Commercial 10

(4-1/8" x 9-1/2")

5 sheets

AR-5316-5320-EX.book 13 ページ２００３年１１月２６日　水曜日　午後５時３分

BEFORE USING THE MACHINE

LOADING PAPER

Make sure that the machine is not copying or printing, and then follow these steps to load paper.

Loading the paper tray

1Gently lift and pull out the paper tray

until it stops.

2Push the pressure plate down until it

locks in place.

Push the centre of the

pressure plate down until

it locks into place.

3Fan the paper.

If the paper is not fanned,

double-feeds or misfeeds

may occur.

4Load paper into the tray.

5Gently push the paper tray into the

machine.

•Do not load paper higher than the line on

the tray (up to 250 sheets).

•Make sure that the paper fits under the tabs

on the right side of the tray.

•Make sure the stack of paper is straight

before loading it. When adding paper, take

the remaining paper out and combine it into

a single stack with the new paper.

Note

If you loaded a different size of paper than

was loaded previously in the tray, go to

"CHANGING A TRAY’S PAPER SIZE

SETTING" (p.16).

Note

AR-5316-5320-EX.book 14 ページ２００３年１１月２６日　水曜日　午後５時３分

BEFORE USING THE MACHINE

Loading the bypass tray

1Unfold the bypass tray.

When feeding large

paper such as B4 and A3

(8-1/2" x 14" and 11" x

17"), pull out the bypass

tray extension.

2Set the paper guides to the copy

paper width.

3Insert the paper (print face down) all

the way into the bypass tray.

To prevent a misfeed,

verify once more that the

paper guides are

adjusted to the width of

the paper.

Important points when inserting paper in the bypass tray

•Up to 100 sheets of standard copy paper can be set in the bypass tray.

•Be sure to place A6, A5 or 5-1/2" x 8-1/2" size paper or envelopes horizontally as shown in the following diagram

().

•When loading envelopes, make sure that they are straight and flat and do not have loosely glued construction

flaps (not the closure flap).

•Special papers except SHARP recommended transparency film, labels, and envelopes must be fed one sheet at a

time through the bypass tray.

•When adding paper, first remove any paper remaining in the tray, combine it with the paper to be added and then

reload as a single stack. The paper to be added must be the same size and type as the paper already in the tray.

•Do not use paper that is smaller than the original. This may cause smudges or unclean images.

•Do not use paper that has already been printed on by a laser printer or plain paper fax machine. This may cause

smudges or unclean images.

If you loaded paper in the bypass tray, press

the [TRAY SELECT] key ( ) to select the

bypass tray. The bypass tray will not be

selected automatically.

Note

Available Not available

AR-5316-5320-EX.book 15 ページ２００３年１１月２６日　水曜日　午後５時３分

BEFORE USING THE MACHINE

Envelopes

Do not use the following envelopes, as misfeeds will occur.

•Envelopes with metal tabs, clasps, strings, holes, or windows.

•Envelopes with rough fibres, carbon paper, or glossy surfaces.

•Envelopes with two or more flaps.

•Envelopes with tape, film, or paper attached to the flap.

•Envelopes with a fold in the flap.

•Envelopes with glue on the flap to be moistened for sealing.

•Envelopes with labels or stamps.

•Envelopes that are slightly inflated with air.

•Envelopes with glue protruding from the seal area.

•Envelopes with part of the seal area peeled off.

CHANGING A TRAY’S PAPER SIZE SETTING

Follow these steps to change a tray’s paper size setting.

1Hold down the [PAPER SIZE ENTER]

key ( ) for more than 5 seconds to

set the selected paper size.

The currently selected

paper feed location

indicator will blink and the

corresponding paper size

(which is currently set)

indicator will light steadily.

All other indicators will go

out.

2If the machine has two paper trays,

use the [TRAY SELECT] key ( ) to

select the paper tray for which you

wish to change the paper size setting.

Each time the [TRAY

SELECT] key ( ) is

pressed, a paper tray will

be indicated with a

blinking paper feed

location indicator.

3Use the [ORIGINAL SIZE ENTER] key

( ) to select the paper size.

The indicator of the

selected paper size lights

up.

•The paper size setting cannot be changed when the machine has stopped temporarily due to running out of

paper or a misfeed, or during interrupt copying.

•During printing (even in copy mode), the paper size setting cannot be changed.

•A5 (5-1/2" x 8-1/2") size paper can only be selected in upper paper tray.

•Do not load paper that is a different size than the paper size setting. Copying will not be possible.

Note

XTRA

ENTER

TRA

AR-5316-5320-EX.book 16 ページ２００３年１１月２６日　水曜日　午後５時３分

BEFORE USING THE MACHINE

4Squeeze the lock lever of the front

guide and slide the front guide to

match the width of the paper, and

move the left guide to the appropriate

slot as marked on the tray.

•The front guide is a slide-type guide. Grasp the

locking knob on the guide and slide the guide to the

indicator line of the paper to be loaded.

•The left guide is an insert-type guide. Remove it and

then insert it at the indicator line of the paper to be

loaded.

•When using 11" x 17" sized paper store the left guide

in the slot at the left front of the paper tray.

5Press the [START] key ( ) and then

the [PAPER SIZE ENTER] key ( ).

To change the paper size

setting of another tray,

repeat steps 2 to 5 after

pressing the [START]

key ( ).

Important points when using the printer mode

•Make sure that the tray's paper size setting is the

same as the tray's paper size setting in the printer

driver. For example, if the tray's paper size setting is

A4R, set "Setting Paper Size" to "A4-R". For more

information, see "CONFIGURING THE PRINTER

DRIVER" in the "Software Setup Guide".

Affix the paper size label for the paper size

selected in step 3 to the label position on the

right end of the tray.

Left guide

Front guide

Note

AR-5316-5320-EX.book 17 ページ２００３年１１月２６日　水曜日　午後５時３分

2Chapter 2

COPY FUNCTIONS

This chapter explains basic copying functions such as normal copying, reduction or enlargement, and exposure adjustment.

NORMAL COPYING

This section explains how to make a regular copy.

If "Auditing mode" has been enabled (p.39), enter your 3-digit account number.

Copying from the document glass

1Open the document cover/SPF, and

place the original.

Place the original face

down on the document

glass. Align it with the

original size scale.

2Close the document cover/SPF.

3Press the [ORIGINAL SIZE ENTER]

key ( ) and select the original size.

When the original size is

selected, the tray with the

same size of paper is

automatically selected.

(Two-tray model only)

●

Make sure that the PAPER SIZE indicator lights up.

If the indicator is not lit, no tray has the same size of

paper as the original. Load paper of the required size

in a tray, or select the bypass tray with the [TRAY

SELECT] key ( ) and copy from the bypass tray.

●The bypass tray must be manually selected.

●

To copy on paper of a different size than the original,

select the paper with the [TRAY SELECT] key ( ).

●

If the ORIGINAL SIZE indicator is blinking, rorate the

original so that it is in the same orientation as the

blinking ORIGINAL SIZE indicator.

4Set the number of copies.

5Press the [START] key ( ) to begin

copying.

The copy is delivered to

the paper output tray.

An original up to A3 (11" x 17") can be placed

on the document glass.

Note

•The paper output tray can hold up to 250

sheets of paper.

•About one minute after copying ends, "Auto

clear" activates and restores the copy

settings to the initial settings. (p.12) The

setting for "Auto clear time" can be changed

in the user programs. (p.33)

•Press the [CLEAR] key ( ) to stop

copying in the middle of a run.

ENTER

XTRA

Note

AR-5316-5320-EX.book 18 ページ２００３年１１月２６日　水曜日　午後５時３分

COPY FUNCTIONS

Copying from the SPF

1Make sure that an original has not

been left on the document glass.

Close the SPF.

2Adjust the original guides to the size

of the original(s).

3Set the original(s) face up in the

document feeder tray.

●Insert the original into the document feeder tray as

far as it will go. When the original is set, the SPF

indicator will light up.

●The ORIGINAL SIZE indicator corresponding to the

size of the original lights up.

●

If the

ORIGINAL

SIZE indicator is blinking, rorate

the original so that it is in the same orientation as the

blinking ORIGINAL SIZE indicator.

●Make sure that the PAPER SIZE indicator is lit.

If the indicator is not lit, no tray has the same size of

paper as the original. Load paper of the required

size in a tray, or select the bypass tray with the

[TRAY SELECT] key ( ) and copy from the

bypass tray.

●The bypass tray must be manually selected.

●To copy on paper of a different size than the

original, select the paper with the [TRAY SELECT]

key ( ).

4Set the number of copies.

5Press the [START] key ( ) to begin

copying.

The copy is delivered to

the paper output tray.

Do not place originals of different sizes

together in the document feeder tray. This

may cause misfeeds.

Note

•The paper output tray can hold up to 250

sheets of paper.

•About one minute after copying ends, "Auto

clear" activates and restores the copy

settings to the initial settings. (p.12) The

setting for "Auto clear" time can be changed

in the user programs. (p.33)

•Press the [CLEAR] key ( ) to stop

copying in the middle of a run.

•If you find it difficult to remove the original

from the document feeder tray, open the

feeding roller cover first and then remove

the original. If you remove the original

without opening the feeding roller cover, the

original may become dirty.

Note

AR-5316-5320-EX.book 19 ページ２００３年１１月２６日　水曜日　午後５時３分

COPY FUNCTIONS

Auto paper select mode (Two-tray model only)

When the AUTO PAPER SELECT indicator ( ) lights up, "Auto paper select mode" is enabled. This function

automatically selects the paper that is the same size as the original A5, A4, A4R, B4, A3 (5-1/2" x 8-1/2", 8-1/2" x

11", 8-1/2" x 11"R, 8-1/2" x 13", 8-1/2" x 14" and 11" x 17") paper. "Auto paper select mode" can be disabled in the

user programs. (p.33)

•The sizes of paper that can be loaded vary by country and region.

•If a zoom setting is selected after placing the original, the paper size that is appropriate for the zoom setting will

be automatically selected.

•"Auto paper select mode" is cancelled if the automatic ratio selection is enabled (p.22) or if a tray is selected

with the [TRAY SELECT] key ( ). Auto paper select resumes operation when the [CLEAR ALL] key ( ) is

pressed or when "Auto clear time" activates.

Removing the document cover

To copy large originals like newspapers, remove the

document cover. To remove the cover, lift straight

up as shown. To replace the cover, do the reverse.

The SPF cannot be removed.

Copying books or originals with folds or

creases

Press down on the document cover/SPF while

copying as shown. If the document cover/SPF is not

completely closed, shadows may appear on the

copy or it may be fuzzy. Straighten originals with

folds or creases well before placing.

Originals that can be used in the SPF

Originals that are A5 to A3 (5-1/2" x 8-1/2" to 11" x

17") and 56 g/m2 to 90 g/m2 (15 lbs. to 24 lbs.) can

be used. A maximum of 40 pages can be placed at

once.

For originals that are B4 (8-1/2" x 14") or larger (B4,

A3 (8-1/2" x 14", 11" x 17")), a maximum of 30

pages can be placed at once.

Originals that cannot be used in the SPF

The following originals cannot be used. These may

cause misfeeds or smudging and unclear images.

•Transparencies, tracing paper, other transparent or

translucent paper, and photographs.

•Carbon paper, thermal paper.

•Originals that are creased, folded, or torn.

•Glued originals, cut-out originals.

•Originals with binder holes.

•Originals printed using an ink ribbon (thermal

transfer printing), originals on thermal transfer

paper.

Stream feeding mode

If "Stream feeding mode" is enabled in the user

programs (p.33), the SPF indicator will blink for

about 5 seconds after all originals are fed. If a new

original is placed in the SPF during this time, the

original will be automatically fed in and copying will

begin.

AUTO

•Make sure that there are no paper clips or

staples on the original.

•Straighten curled originals before placing

them in the document feeder tray. Curled

originals may cause misfeeds.

Note

AR-5316-5320-EX.book 20 ページ２００３年１１月２６日　水曜日　午後５時３分

COPY FUNCTIONS

MAKING A COPY DARKER OR LIGHTER

Automatic exposure adjustment is initially enabled. This function automatically adjusts the copy image according to

the original being copied. If you wish to select the exposure level yourself, follow the steps below. (Select from two

original types and five exposure levels for each original type.) The exposure level used in automatic exposure

adjustment can also be changed. ("ADJUSTING THE AUTOMATIC EXPOSURE LEVEL" (p.31) )

Original types

●

AUTO......Automatic exposure adjustment is enabled and the exposure is automatically adjusted according to the

original being copied. The exposure is lowered for coloured areas and background shadows.

●

TEXT.......The exposure is raised for light areas and lowered for dark backgrounds to make text easier to read.

●

PHOTO ...Halftones in the photo are reproduced with greater clarity.

1Press the [AUTO/TEXT/PHOTO] key

( / / ) to select the original

type.

To adjust the exposure of

a text original manually,

press until the TEXT

indicator ( ) lights.

To copy a photo, press

until the PHOTO

indicator ( ) lights.

2Press the [Light] key ( ) or [Dark]

key ( ) to adjust the exposure.

For a darker image,

press the [Dark] key

( ). For a lighter image,

press the [Light] key

().

If exposure level 2 or 4 is

selected, the two

indicators will light

simultaneously.

SELECTING THE TRAY

If you wish to use a tray other than the automatically selected tray (for example you wish to enlarge or reduce the

copy or use the bypass tray), press the [TRAY SELECT] key ( ) to select the desired tray.

Auto tray switching (Two-tray model only)

If the tray runs out of paper during copying and there is another tray with the same size of paper and the same

feeding orientation (horizontal or vertical), the other tray is automatically selected and copying continues. "Auto tray

switching" can be disabled in the user programs (p.33).

To return to automatic adjustment, press until

the AUTO indicator ( ) lights.

AUTO

Note

AUTO

Exposure value guidelines

1 – 2 Dark originals like newspapers

3 Normal originals

4 – 5 Coloured text or text written in pencil

AUTO

135

Note

•If the desired PAPER SIZE indicator does not light up, change the paper in the tray to the desired paper size.

(p.16)

•Automatic ratio selection (p.22) does not operate when the bypass tray or a tray set for a special paper size is

selected.

Note

AR-5316-5320-EX.book 21 ページ２００３年１１月２６日　水曜日　午後５時３分

COPY FUNCTIONS

SETTING THE NUMBER OF COPIES

Press the numeric keys to set the number of copies.

●The set number of copies appears in the display. A

maximum of 999 copies (factory default setting)

can be set.

●If you wish to make only a single copy, copying is

possible with the display showing "0".

Important note when making a large number

of copies

The maximum number of copies can be changed in

the user programs. (p.34)

When the maximum number of pages (about 250

pages) that can be held in the paper output tray are

output, copying will temporarily stop. When this

happens, promptly remove the copies and press the

[START] key ( ) to resume copying. Copying will

also stop after about 500 pages and 750 pages.

Remove the pages and resume copying in the same

way.

REDUCTION/ENLARGEMENT/ZOOM

The zoom function enables precise copy ratio selection from 25% to 400% in increments of 1%.

There are three ways to enlarge and reduce copies, as explained below.

•Reduction and enlargement ratios can be selected automatically with the [AUTO IMAGE] key ( ).

"AUTOMATIC RATIO SELECTION" (below)

•Reduction and enlargement ratios can be selected manually with the [PRESET RATIO] selector keys

( , ) and/or the [ZOOM] keys ( , ).

"MANUAL RATIO SELECTION" (p.23)

•Separate settings can be selected for the vertical and horizontal ratios.

"SELECTING THE VERTICAL AND HORIZONTAL COPY RATIOS SEPARATELY" (p.24)

Ratios that can be selected will vary depending on whether the original is placed on the document glass or in the

SPF.

AUTOMATIC RATIO SELECTION

1Place the original(s) in the document

feeder tray or on the document glass.

2If the original is placed on the

document glass, select the original

size. (p.18)

3Use the [TRAY SELECT] key ( ) to

select the paper tray with the desired

paper size.

This feature will not work

when using copy paper

of non-standard size or

when using the bypass

tray.

If you enter the wrong number, press the

[CLEAR] key ( ) and enter the correct

number.

Note

AUTO %

Original position Selectable ratios

Document glass 25% – 400%

SPF 50% – 200%

Automatic ratio selection can be used when the

original size is A5, A4, A4R, B4, A3 (5-1/2" x

8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13",

8-1/2" x 14" or 11" x 17"). The sizes of paper

that can be loaded vary by country and region. It

cannot be used for other sizes.

Note

AR-5316-5320-EX.book 22 ページ２００３年１１月２６日　水曜日　午後５時３分

COPY FUNCTIONS

4Press the [AUTO IMAGE] key ( ).

The AUTO IMAGE

indicator ( ) lights

up and the appropriate

ratio for the original size

and paper size is

selected. (The indicator

of the selected ratio will

light up.)

5Set the number of copies and other

copy settings, and then press the

[START] key ( ).

The copy will be delivered to the paper output

tray.

MANUAL RATIO SELECTION

Copies can be reduced down to 25% or enlarged up to 400%. The [PRESET RATIO] selector keys ( , ) can be

pressed to quickly select a ratio from among eight preset ratios. In addition, the [Zoom] keys ( , ) can be

pressed to select the ratio in increments of 1%.

1Place the original(s) in the document

feeder tray or on the document glass.

If the original is placed on the document

glass, select the original size. (p.18)

3Use the [PRESET RATIO] selector

keys ( , ) and [Zoom] keys ( , )

to select the desired copy ratio.

Selecting a preset ratio

Press the [PRESET

RATIO] selector key ( )

to move up through the

preset ratios.

Press the [PRESET

RATIO] selector key ( )

to move down through

the preset ratios.

Fine adjustment of the

ratio

Any ratio from 25% to

400% can be set in

increments of 1%.

Press a [PRESET RATIO] selector key ( or ) to

set the approximate ratio, then press the [Zoom] keys

( or ) to increase or decrease the ratio.

To decrease or increase the zoom ratio rapidly, hold

down the [Zoom] keys ( or ).

When a [Zoom] key ( or ) is pressed, the ZOOM

indicator will light up and the zoom ratio will appear in

the display for about two seconds.

4Set the number of copies and other

copy settings, and then press the

[START] key ( ).

The copy will be delivered to the paper output

tray.

•

If the ORIGINAL SIZE indicator blinks,

change the orientation of the placed original.

•If the copy is made when a PRESET

RATIO selector indicator is blinking, the

copied image may run off the page.

AUTO %

Note

To cancel automatic ratio selection, press the

[AUTO IMAGE] key ( ) again.

Note

AUTO %

200

141

122

115

100

25 400%

ZOOM

•To verify a zoom setting without changing

the zoom ratio, Hold down the [Copy ratio

display] key ( ). When the key is

released, the display will return to the

number of copies display.

•If the copy is made when a PRESET

RATIO selector indicator or the ZOOM

indicator is blinking, the copied image may

run off the page. To ensure that the image

fits on the page, lower the copy ratio until

the indicator stops blinking and lights

steadily.

•If the PAPER SIZE indicator is not lit, there

is no appropriate paper. Load appropriate

paper in a paper tray. (p.14)

To return the ratio to 100%, press the

[PRESET RATIO] selector key ( or )

until the 100% indicator lights up.

Note

AR-5316-5320-EX.book 23 ページ２００３年１１月２６日　水曜日　午後５時３分

COPY FUNCTIONS

SELECTING THE VERTICAL AND HORIZONTAL

COPY RATIOS SEPARATELY

(XY ZOOM copying)

The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently.

Example:

Reduction only in the horizontal direction.

Ratios that can be selected will vary depending on the position of the original.

1Place the original(s) in the document

feeder tray or on the document glass.

2If the original is placed on the

document glass, select the original

size. (p.18)

3Press the [XY-ZOOM] key ( ).

XY-ZOOM Indicator ( )

lights up.

The current value for the

vertical direction will

appear in the display.

4Use the [PRESET RATIO] selector

keys ( , ) and [Zoom] keys ( , )

to change the copy ratio in the vertical

direction.

Press the [PRESET

RATIO] selector keys

( , ) to select a ratio

close to the desired ratio,

and then press the

[Zoom] keys ( , ) to

adjust the ratio in

increments of 1%.

The ratio appears in the

display.

5Press the [Copy ratio display] key

().

The selected ratio for the

vertical direction will be

entered.

•To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and

then the XY ZOOM feature.

•The XY ZOOM feature cannot be used in combination with the AUTO IMAGE function.

Original position Selectable ratios

Document glass 25% – 400%

SPF 50% – 200%

Original Copy

Note

25 400%

ZOOM

AR-5316-5320-EX.book 24 ページ２００３年１１月２６日　水曜日　午後５時３分

COPY FUNCTIONS

6Use the [PRESET RATIO] selector

keys ( , ) and [Zoom] keys ( , )

to change the copy ratio in the

horizontal direction.

Press the [PRESET RATIO] selector keys ( ,

) to select a ratio close to the desired ratio, and

then press the [Zoom] keys ( , ) to adjust

the ratio in increments of 1%.

The ratio appears in the display.

7Press the [Copy ratio display] key

().

The selected ratio for the horizontal direction will

be entered and the display will change to the

number of copies display.

8Set the number of copies and other

copy settings, and then press the

[START] key ( ).

The copy will be delivered to the paper output

tray.

•To verify the copy ratios, press and hold

down the [Copy ratio display] key ( ).

The vertical and horizontal ratios will be

alternately displayed.

•If you need to change the ratios, press the

[PRESET RATIO] selector keys ( , )

and the [Zoom] keys ( , ) to reset the

ratios, beginning with the vertical ratio.

(step 4)

•To cancel XY ZOOM copy, press the

[XY-ZOOM] key ( ). The XY-ZOOM

indicator ( ) will go off, indicating that the

function is cancelled.

Note

AR-5316-5320-EX.book 25 ページ２００３年１１月２６日　水曜日　午後５時３分

TWO-SIDED COPYING USING THE

BYPASS TRAY

To perform manual two-sided copying, follow these steps.

Example: Copying originals A and B onto each side of one sheet of paper

1Copy original A.

2Place original B as shown below.

Vertically-oriented

original:

If the original is oriented

vertically, place it in the

same orientation as

original A.

Horizontally-oriented

original:

If the original is oriented

horizontally, place it with

the top and bottom and

left and right sides

reversed with respect to

the placement of original

3Turn the copy of original A over, and

without changing the position of the

edge closest to you, insert it in the

bypass tray.

Insert the paper all the

way in.

4Select the bypass tray with the [TRAY

SELECT] key ( ), and then press the

[START] key ( ).

The copy is delivered to the paper output tray.

12 1

Original A Original B Copy

Original A

Copied original A

Original A

Copied original A

Original B

•Copies made on the back side of paper

should always be made one sheet at a time

using the bypass tray.

•Straighten curled or wavy paper before

using it. Curled paper may cause misfeeds,

creases, or a poor-quality image.

Original B

Copied

original A

Original B

Copied

original A

Note

AR-5316-5320-EX.book 26 ページ２００３年１１月２６日　水曜日　午後５時３分

DUAL PAGE COPYING

A dual page original can be automatically separated into two pages during copying. This feature is convenient for

making copies of books and other dual page originals on individual sheets of paper.

1Place the original on the document

glass, aligning the division between

the pages with the size marker ( A4

1/2)). Close the document cover

SPF.

Copying will begin from

the page to the right of

the size marker.

2Set the original size to A3 (11" x 17").

3Press the [DUAL PAGE COPY] key

( ) and make sure that the DUAL

PAGE COPY indicator ( ) is lit.

4Make sure that a paper tray with A4

(8-1/2" x 11") size paper is selected.

5Set the number of copies and other

copy settings, and press the [START]

key ( ).

The copy will be delivered to the paper output

tray.

Original Copy

•A4 (8-1/2" x 11") paper is used for dual page copying.

•When used in combination with XY ZOOM copying, enlargement is not possible.

•Dual page copying cannot be used in combination with the enlargement copying.

•Automatic ratio selection cannot be used when dual page copying is used.

•Dual page copying cannot be selected when an original is placed in the SPF.

Note

To keep the copies in the correct page order

when performing dual page copying over

multiple pages, make sure that the original is

always placed on the document glass with the

lower page number to the right.

A4 8

Note

To cancel dual page copying, press the

[DUAL PAGE COPY] key ( ). The

DUAL PAGE COPY indicator ( ) will go

off, indicating that the function is cancelled.

Note

AR-5316-5320-EX.book 27 ページ２００３年１１月２６日　水曜日　午後５時３分

INTERRUPTING A COPY RUN

(Interrupt copying)

A copy run can be temporarily interrupted to allow another copy job to be performed. When the other job is finished,

the copy run will resume using the original copy settings.

1Press the [INTERRUPT] key ( ) to

interrupt the copy run.

The INTERRUPT

indicator will light up and

the machine will revert to

the initial settings. (p.12)

The INTERRUPT

indicator will blink until

the current copy run

stops.

2Remove the previous original(s) and

place the original(s) of the interrupt

copy job.

3Set the number of copies and other

copy settings and then press the

[START] key ( ).

4When the copy job is finished, press

the [INTERRUPT] key ( ) and remove

the original(s).

The INTERRUPT indicator will go off, indicating

that the interrupt function is no longer operating.

The copy settings will automatically revert to the

settings selected for the copy run before the run

was interrupted.

5Replace the previous original(s) and

press the [START] key ( ).

The interrupted copy run will resume.

Interrupt copying is not possible when the user programs are being configured.

Note

•If the SPF is being used, the copy run will

not stop until the set number of copies is

completed.

•If "Auditing mode" is enabled:

"- - -" will appear in the number of copies

display. Enter your 3-digit account number.

Copying will not be possible unless a

correct account number is entered. (p.39)

INTERRUPT

Note

AR-5316-5320-EX.book 28 ページ２００３年１１月２６日　水曜日　午後５時３分

3Chapter 3

PRINTER FUNCTIONS

The machine includes a USB 1.1 connector and a parallel connector as standard equipment.

A computer can be connected to these connectors to use the machine as a printer.

To use the machine as a printer, the printer driver must first be installed as explained in the "Software Setup Guide".

USING THE PRINTER MODE

The procedure for loading paper is the same as for loading copy paper. See "LOADING PAPER". (p.13)

BASIC PROCEDURE FOR PRINTING

The basic procedure for printing is explained below. To use convenient printer functions, see the "Online Manual" or

the printer driver help file.

1Make sure that paper is loaded in the

tray.

The procedure for loading paper is the same as for

copying. See "LOADING PAPER" (p.13) and make

sure the paper that you wish to use is loaded.

2Make sure that the ON LINE indicator

( ) on the operation panel is lit.

If the ON LINE indicator

( ) is not lit, press the [ON

LINE] key ( ). When the

indicator is not lit, the

machine is off-line and

cannot print. When the

indicator is blinking, a print

job is transferred to the

machine.

3Open the file that you wish to print

and select "Print" from the File menu.

4Make sure that the printer driver for

the machine is selected, and select

print settings in the printer driver.

For information on the settings in the printer

driver, see the "Online Manual", the "Software

Setup Guide", or the printer driver help file.

5Click the "Print" button or the "OK"

button to begin printing.

The print job will be delivered to the paper output

tray.

Important points when setting the paper size

•Make sure that the tray's paper size setting is the

same as the tray's paper size setting in the printer

driver. For example, if the tray's paper size setting is

A4R, set "Setting Paper Size" to "A4-R". For more

information, see "CONFIGURING THE PRINTER

DRIVER" in the "Software Setup Guide".

•If a problem occurs in printer mode, see "TROUBLESHOOTING" (p.40).

•When interrupt copying is being performed, printing is not possible.

Note

•Print jobs received while the machine is copying will be stored in memory. When the copy job is finished, the

print jobs will begin printing.

•Printing is not possible when the front or side cover is opened for machine maintenance, or when a misfeed

occurs or the machine runs out of paper or toner, or when the drum cartridge reaches its replacement time.

•If an original misfeed occurs in the SPF, printing will not be possible until the misfed original is removed and the

SPF is restored to a usable state.

Note

Make sure that the paper size setting on the

machine is the same as the paper size set in

the printer driver.

Note

AR-5316-5320-EX.book 29 ページ２００３年１１月２６日　水曜日　午後５時３分

PRINTER FUNCTIONS

Pausing a print job

To pause a print job during printing, press the [ON LINE] key ( ) on the operation panel to switch the machine

off-line. Printing will be paused and the ON LINE indicator ( ) will blink.

To cancel a print job, press the [CLEAR] key ( ) or the [CLEAR ALL] key ( ).

To resume printing, press the [ON LINE] key ( ) to switch the machine online.

When "Use close paper size" is disabled

The PAPER SIZE indicator on the operation panel will blink. You can press the [TRAY SELECT] key ( ) to select a

tray manually, or load paper in the bypass tray and press the [ON LINE] key ( ) to begin printing.

When "Use close paper size" is enabled

Printing will take place using a size of paper that is close to the size of the print image.

OPERATION IN COPY AND PRINTER MODES

Some operations cannot be performed simultaneously when the machine is being used in printer mode or copy

mode.

*1Can be used after pressing the [INTERRUPT] key ( ).

*2Printing will begin when the [CLEAR ALL] key ( ) is pressed after the copy job is finished, or when the [ON LINE] key ( ) is

pressed to switch the machine online. Printing will also begin after the set auto clear time elapses, or after 60 seconds if "Auto

clear time" is disabled.

*3The print job is paused and copying begins.

Modes Copying Printing

Copy Copy key input Yes Yes

During copying Yes*1No*2

Printer During printing Yes*3No

AR-5316-5320-EX.book 30 ページ２００３年１１月２６日　水曜日　午後５時３分

4Chapter 4

USER SETTINGS

This chapter explains how to set the automatic exposure level, toner save mode/high image quality mode, and the

user programs, which are custom settings that control fine points of the machine’s operation.

ADJUSTING THE AUTOMATIC

EXPOSURE LEVEL

The exposure level used in automatic exposure adjustment, which automatically adjusts the copy exposure

according to the original, can be adjusted. If copies tend to be too dark or too light when automatic exposure

adjustment is used, follow the steps below to adjust the automatic exposure level.

The automatic exposure level can be adjusted separately for the document glass and the SPF.

1To adjust the automatic exposure

level in the SPF, place the original in

the SPF. (p.19)

Make sure that the SPF indicator is lit.

2Press the [AUTO/TEXT/PHOTO] key

( / / ) to select "PHOTO"

().

3Hold down the [AUTO/TEXT/PHOTO]

key ( / / ) until the AUTO

indicator ( ) blinks.

The exposure level

indicators show the

current setting.

4Press the [Light] key ( ) or [Dark]

key ( ) to lighten or darken the

automatic exposure level as desired.

5Press the [AUTO/TEXT/PHOTO] key

( / / ) to complete the

setting.

The AUTO indicator ( ) stops blinking and

lights steadily.

The copy and printer cannot be used while the automatic exposure level is being adjusted.

Note

To adjust the automatic exposure level for

copies made from originals placed on the

document glass, proceed to step 2.

Note

AUTO

135

After adjusting the automatic exposure level,

it is recommended that you make a test copy

to check the new level.

135

AUTO

Note

AR-5316-5320-EX.book 31 ページ２００３年１１月２６日　水曜日　午後５時３分

TONER SAVE MODE AND HIGH

IMAGE QUALITY MODE

Toner save mode can be enabled to reduce toner consumption by about 10%.

The high image quality mode improves copy image quality in the automatic and manual exposure modes by

increasing copy density with a slight increase of toner consumption.

To switch between toner save mode and high image quality mode, follow the steps below.

1Press the [AUTO/TEXT/PHOTO] key

( / / ) to select "TEXT"

().

2Hold down the [AUTO/TEXT/PHOTO]

key ( / / ) until the PHOTO

indicator ( ) blinks.

The exposure level

indicators show the

current setting.

3To enable toner save mode, press the

[Light] key ( ). To enable high image

quality mode, press the [Dark] key

().

When enabling toner

save mode, make sure

that "1" is lit.

When enabling high

image quality mode,

make sure that "5" is lit.

4Press the [AUTO/TEXT/PHOTO] key

( / / ) to complete the

setting.

The PHOTO indicator ( ) stops blinking and

lights steadily.

In Europe, high image quality mode is initially selected. In regions other than Europe, toner save mode is initially

selected.

Note

AUTO

135

AUTO

AR-5316-5320-EX.book 32 ページ２００３年１１月２６日　水曜日　午後５時３分

CUSTOMISING SETTINGS

(User programs)

The user programs allow you to customise the machine to match your needs.

USER PROGRAMS

Program

number Program name

Setting codes

(factory default setting

appears in bold)

Explanation

1 Auto clear time

1: OFF

2: 10 sec.

3: 20 sec.

4: 60 sec.

5: 90 sec.

6: 120 sec.

•"Auto clear time" automatically returns the

copy settings to the initial settings (p.12) when

a certain period of time elapses after a copy is

made. This program is used to select the

period of time. "Auto clear time" can also be

disabled.

2 Preheat mode

1: 1 min.

2: 5 min.

3: 30 min.

4: 60 min.

5: 120 min.

6: 240 min.

•This function automatically switches the

machine to a low power consumption state if

the set duration of time elapses without the

machine being used when the power is on.

The POWER SAVE indicator ( ) lights up,

however, the keys on the operation panel can

be used. Normal operation automatically

resumes when a key on the operation panel is

pressed, a print job is received or an original is

placed.

3Auto power shut-off

timer

1: 5 min.

2: 30 min.

3: 60 min.

4: 120 min.

5: 240 min.

•This function automatically switches the

machine to a state that consumes even less

power than preheat mode if the set duration of

time elapses without the machine being used

when the power is on. All lights except the

POWER SAVE indicator ( ) and ON LINE

indicator ( ) go off. To resume normal

operation, press the [START] key ( ).

Normal operation also resumes automatically

when a print job is received. While in auto

power shut-off mode, no keys (except the

[START] key ( )) can be used.

Stream feeding mode

0: OFF

1: ON

•When copying using the SPF, during the

period of time that the SPF indicator blinks

after an original has been scanned

(about 5 seconds), a subsequent original can

be placed and automatically fed into the

machine.

5Auto power shut-off

setting

0: OFF

1: ON

•Use this setting to enable or disable auto

power shut-off.

8Auto paper select

mode

0: OFF

1: ON

•This function automatically selects paper that

is the same size as the original placed in the

SPF, or the same size as that selected with

the [ORIGINAL SIZE ENTER] key ( ) The

function can be disabled.

9 Auto tray switching

0: OFF

1: ON

•If the paper runs out during printing and there

is paper of the same size and orientation in

another tray, this function automatically

switches to that tray (excluding the bypass

tray). The function can be disabled.

10 to 15 Auditing mode –See "AUDITING MODE SETTINGS" (p.36).

ENTER

*1When the SPF is installed.

*2On model with the two trays.

AR-5316-5320-EX.book 33 ページ２００３年１１月２６日　水曜日　午後５時３分

USER SETTINGS

*3AR-5316/AR-5316 X is as follows:

1: Paper tray (factory default),

5: Bypass tray

23 Resolution in

Auto/Text mode

1: 300 dpi

2: 600 dpi

•This setting is used to change the copy

resolution in AUTO and TEXT mode from 600

x 300 dpi to 600 x 600 dpi (high-quality mode).

Scanning is slower when high-quality mode is

used.

25 Key auto repeat 0: OFF

1: ON

•Use this setting to select whether or not

holding down a key causes repeated input of

the key. For keys that normally cause a set

value to increase when held down (for

example, holding down the [ZOOM] key ( ,

)), this program can be used to have the set

value not change when the key is held down.

26 Key press time

1: Minimum

(current response

speed)

2: 0.5 sec.

3: 1.0 sec.

4: 1.5 sec.

5: 2.0 sec.

•Use this setting to select how long a key must

be pressed for the input to be accepted. By

selecting a longer time, you can prevent

settings from being changed by the accidental

pressing of a key.

27 Audible signals volume

1: Short beep

2: Long beep

3: OFF

•This sets the volume of beep signals. (p.35)

28 Base setting beep

signal

0: OFF

1: ON

•Use this to sound a beep when a base setting

is selected. (p.35)

29 Number of copies limit 1: 99 copies

2: 999 copies

•Use this setting to select 99 or 999 for the

maximum number of copies.

30 Use close paper size 0: OFF

1: ON

•When this function is enabled, printing in

printer mode will automatically continue using

a different size of paper if the specified size of

paper runs out in all trays. This feature does

not function in copy mode.

31 Default tray setting

1: Upper paper tray*3

2: Lower paper tray*3

5: Bypass tray*3

•Use this program to select a default tray. This

tray is automatically selected each time the

power is turned on or each time the machine

reverts to the initial settings.

32 Default exposure

mode

1: AUTO

2: TEXT

3: PHOTO

•Use this program to set "AUTO", "TEXT", or

"PHOTO" as the default exposure mode.

Program

number Program name

Setting codes

(factory default setting

appears in bold)

Explanation

AR-5316-5320-EX.book 34 ページ２００３年１１月２６日　水曜日　午後５時３分

USER SETTINGS

SELECTING A SETTING FOR A USER PROGRAM

1Hold down the [Light] key ( ) until

the alarm indicators ( , , , ,

) blink.

The display shows "- -"

with the left hyphen

blinking.

2Enter the program number with the

numeric keys.

•See "USER

PROGRAMS" (p.33 to

p.34) for the program

numbers.

•The selected program

number blinks.

•For example, to select

"Auto clear timer",

press the [1] key.

3Press the [START] key ( ).

•The selected program

number stops blinking

and lights steadily.

•The currently selected

setting code blinks on

the right side of the

display.

4Enter the desired setting code by

pressing a numeric key.

•For the setting codes,

see "USER

PROGRAMS". (p.33 to

p.34)

•The selected setting

code blinks.

•For example, to select

90 seconds, press the

[5] key.

5Press the [START] key ( ).

The selected setting

code stops blinking and

lights steadily.

6Press the [Light] key ( ) to complete

the settings.

The alarm indicators ( , , , , ) go

off and the display returns to the number of

copies display.

Audible signals (key entry beep, invalid key beep, base setting beep)

The machine sounds three different types of beep signals: a key entry beep that sounds when a valid key is

pressed, an invalid key beep that sounds when an invalid key is pressed, and a base setting beep that sounds

when a setting is the same as the base setting (base settings are explained below). The base setting beep is

initially disabled. If you wish to enable the base setting beep, see "Base setting beep signal" on page 34. If you

wish to change the volume of the beep signals or disable them, see "Audible signals volume" on page 34.

The beep patterns of each type of beep signal are as follows:

Key entry beep ......................... One beep

Invalid key beep ......................Two beeps

Base setting beep ................ Three beeps

Base settings

The base settings are preset standard selections for each copy setting. The base settings are as follows:

Copy ratio ........................................ 100%

Light and Dark indicator........................ 3

Paper feed location ....... Upper paper tray

ORIGINAL SIZE..................A4 (8-1/2" x 11")

AUTO/TEXT/PHOTO ( / / )

............................................................ AUTO

If you enter the wrong number, press the

[CLEAR] key ( ) and then enter the correct

number.

135

READ END

Note

If you enter the wrong number, press the

[CLEAR] key ( ) and return to step 2.

To select a setting for another user program,

press the [CLEAR] key ( ) and then return

to step 2.

Note

AUTO

AR-5316-5320-EX.book 35 ページ２００３年１１月２６日　水曜日　午後５時３分

SETTINGS FOR AUDITING MODE

AUDITING MODE

When "Auditing mode" is enabled, a count is kept of the number of copies made by each account (up to 20 accounts

can be established), and the counts can be displayed and totalled as necessary. In "Auditing mode", the display

shows "- - -", and this indicates that a 3-digit account number must be entered in order to use the machine for

copying.

AUDITING MODE SETTINGS

The administrator of the machine should complete the following settings:

•Enable "Auditing mode" (p.38)

•Account number entry (p.38)

Note

Program

number Program name

Setting codes

(factory default settings

are indicated in bold)

Explanation

10 Auditing mode 0: OFF

1: ON

Use to enable or disable "Auditing mode".

"Auditing mode" is initially disabled.

11 Account number entry None Use to set up account numbers. Up to 20

accounts can be established.

12 Account number

change None Use to change an account number.

13 Account number

deletion

0: Delete single account

1: Delete all accounts

Use to delete an account number.

A single account number can be deleted, or all

account numbers at once.

14 Number of copies per

account None

This displays the number of copies made by

each account.

The maximum count is 49,999. If this number is

exceeded, the count will start over from 0.

15 Resetting account

0: Reset single account

1: Reset all accounts

Use to reset the copy count of an account to 0.

The copy count of a single account or of all

accounts can be reset.

AR-5316-5320-EX.book 36 ページ２００３年１１月２６日　水曜日　午後５時３分

USER SETTINGS

SELECTING AUDITING MODE SETTINGS

1Hold down the [Light] key ( ) until

the alarm indicators ( , , , ,

) blink.

The display shows "- -"

with the left hyphen

blinking.

2Enter the program number with the

numeric keys.

•See "AUDITING MODE

SETTINGS" (p.36) for

the program numbers.

•The selected program

number blinks.

•For example, to select

"Auditing mode", enter

"10".

3Press the [START] key ( ).

•The selected program

number stops blinking

and lights steadily.

•The currently selected

setting code blinks on

the right side of the

display.

4Enter the desired setting code for the

program as explained in the detailed

procedures on the following pages.

For the setting codes, see "AUDITING MODE

SETTINGS". (p.36)

5Press the [Light] key ( ) to complete

the settings.

The alarm indicators ( , , , , ) go

off and the display returns to the number of

copies display.

If you enter the wrong number, press the

[CLEAR] key ( ) and then enter the correct

number.

•If you enter the wrong number, press the

[CLEAR] key ( ) and return to step 2.

•If "E" (error code) blinks in the first digit of

the display, press the [CLEAR] key ( )

and return to step 2.

135

READ END

Note

AR-5316-5320-EX.book 37 ページ２００３年１１月２６日　水曜日　午後５時３分

USER SETTINGS

Auditing mode

(program No.10)

1 Press the [1] key to enable "Auditing

mode" or the [0] key to disable it, and then

press the [START] key ( ).

2 Press the [CLEAR] key ( ).

Account number entry

(program No.11)

If 20 accounts have already been established, the

error code "11E" will appear in the display.

1 Use the numeric keys to enter a 3-digit

number (any number except "000") and

then press the [START] key ( ).

2 Press the [CLEAR] key ( ).

Account number change

(program No.12)

Use this procedure to change an account number. If

no account numbers have been established, the error

code "12E" will appear in the display.

1 Press the [Copy ratio display] key ( ) to

select the account number that you wish to

change, and then press the [START] key

().

The display will show 3 blinking hyphens "- - -".

2 Press the numeric keys to enter a new

account number (any 3-digit number

except "000"), and then press the [START]

key ( ).

3 When finished, press the [CLEAR] key

().

Account number deletion

(program No.13)

Use this procedure to delete account numbers. A

single account number can be deleted, or all account

numbers at once.

If no account numbers have been established, the

error code "13E" will appear in the display.

[Deleting all accounts at once]

Press the [1] key and then press the [START]

key ( ).

All account numbers will be deleted.

[Deleting a single account]

1 Press the [0] key, and then press the

[START] key ( ).

2 Select the account number to be deleted

with the [Copy ratio display] key ( ) and

then press the [START] key ( ).

Number of copies per account

(program No.14)

Use this procedure to display the copy count of each

account. If no account numbers have been

established, the error code "14E" will appear in the

display.

1 Select the account number with the [Copy

ratio display] key ( ).

2 Hold down the [0] key.

The copy count of the selected account will appear in

the display while you hold down the [0] key. The count

is displayed sequentially as shown below.

Example: 12,345 copies

3 When finished, press the [CLEAR] key

().

After enabling "Auditing mode", use "Account

number entry" to establish account numbers

for each account (up 20 accounts can be

established).

•If you enter "000" or a number that has

already been stored, the number will blink

in the display. Enter a different number. (Up

to 20 accounts can be established.)

•Repeat the same procedure to enter any

other account numbers that you wish to

establish.

•Keep a record of what group is using each

account number (account names cannot be

stored, so keep a record to prevent

confusion when totalling account values).

•If you enter "000" or a number that has

already been stored, the number will blink

in the display. Enter a different number.

•To change another account number, repeat

steps 1 and 2.

Note

To delete another account number, enter the

program number (13) for account number

deletion and then repeat the procedure for

"Deleting a single account".

•Each A3 (11" x 17") size page is counted as

two pages.

•To view the copy count of another account,

repeat steps 1 and 2.

Note

AR-5316-5320-EX.book 38 ページ２００３年１１月２６日　水曜日　午後５時３分

USER SETTINGS

Resetting account

(program No.15)

The copy count of a single account or all accounts can

be reset to 0. If no account numbers have been

established, the error code "15E" will appear in the

display.

[Resetting all accounts]

Press the [1] key and then press the [START]

key ( ).

The copy counts of all accounts will be deleted.

[Resetting a single account]

1 Press the [0] key, and then press the

[START] key ( ).

2 Select the account number to be reset with

the [Copy ratio display] key ( ) and then

press the [START] key ( ).

Copying when "Auditing mode" is

enabled

When "Auditing mode" is enabled, "- - -" appears in the

display.

1Enter your 3-digit account number

with the numeric keys.

When you enter your account number, "0"

appears in the display to indicate that copying is

possible.

2Follow the appropriate steps to make

the copy.

3When finished, press the [AUDIT

CLEAR] key ( ).

To reset another account number, enter the

program number (15) for account number

deletion and then repeat the procedure for

"Resetting a single account".

Note

If you enter an incorrect number, press the

[CLEAR] key ( ) and then enter the correct

number.

If you are performing an interrupt copy (p.28),

be sure to press the [INTERRUPT] key ( )

when finished to exit interrupt mode.

If a misfeed occurs or the paper runs out

during copying, your session will not end even

if the [AUDIT CLEAR] key ( ) is

pressed.

Note

ACC.#-C

Note

ACC.#-C

AR-5316-5320-EX.book 39 ページ２００３年１１月２６日　水曜日　午後５時３分

5Chapter 5

TROUBLESHOOTING

This chapter describes troubleshooting and misfeed removal.

TROUBLESHOOTING

If you experience difficulty using the machine, check the following troubleshooting guide before calling for service.

Many problems can be easily resolved by the user. If you are unable to solve the problem using the troubleshooting

guide, turn off the power switch and unplug the machine, and contact your authorised service representative.

MACHINE/COPYING PROBLEMS

The machine does not operate. ................................................................................................................. 41

Copies are too dark or too light.................................................................................................................. 41

Blank copies............................................................................................................................................... 41

Part of the image is cut off or there is too much blank space. ................................................................... 41

Wrinkles appear in the paper or the image disappears in places. ............................................................. 41

Paper misfeed............................................................................................................................................ 42

Original size not selected automatically..................................................................................................... 42

Copies are smudged or dirty...................................................................................................................... 43

White or black lines appear on copies. ...................................................................................................... 43

Paper size for a paper tray cannot be set. ................................................................................................. 43

A copy job stops before it is finished.......................................................................................................... 43

The POWER SAVE indicator ( ) is lit. ..................................................................................................... 43

Any one of the alarm indicators ( ,,, ,) is lit or blinking. ..................................................... 43

Lighting fixture flickers. .............................................................................................................................. 43

PRINTING PROBLEMS

The machine does not print. (ON LINE indicator ( ) does not blink.) ....................................................... 44

The machine does not print. (ON LINE indicator ( ) was blinking.) ......................................................... 44

Printing is slow. .......................................................................................................................................... 45

The printed image is light and uneven. ...................................................................................................... 45

The printed image is dirty........................................................................................................................... 45

The printed image is skewed or it runs off the paper. ................................................................................ 45

Any one of the alarm indicators ( ,, , ,) is lit or blinking. ................................................... 45

Removing the software .............................................................................................................................. 45

INDICATORS AND DISPLAY MESSAGES.................................................. 46

MISFEED REMOVAL .................................................................................... 47

REPLACING THE TONER CARTRIDGE...................................................... 54

AR-5316-5320-EX.book 40 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

MACHINE/COPYING PROBLEMS

The following problems are related to the general operation of the machine and copying.

Problem Cause and solution Page

The machine does not operate.

The machine is not plugged into a power outlet.

→Plug the machine into a grounded outlet. –

Power switch OFF.

→Turn the power switch ON. 12

The POWER SAVE indicator ( ) is blinking.

→Indicates that the machine is warming up. Copies cannot be

made until the machine has finished warming up.

The front cover or the side cover is not completely

closed.

→Close the front cover or the side cover.

–

The machine is in auto power shut-off mode.

→In auto power shut-off mode, all lights are off except the POWER

SAVE indicator ( ) and ON LINE indicator ( ). Press the

[START] key ( ) to resume normal operation.

PAPER SIZE indicator is blinking.

→A blinking PAPER SIZE indicator means that the size of paper

loaded in the tray is different from the paper size setting for the

tray. Change the paper size setting.

To clear the display, do one of the following:

•Use the [TRAY SELECT] key ( ) to change the tray selection.

•Open and close the tray.

•Press the [CLEAR ALL] key ( ).

Copies are too dark or too light.

Select the correct original type for the original.

→Select AUTO with the [AUTO/TEXT/PHOTO] key or press the

[Light] key ( ) and [Dark] key ( ) to manually select an

appropriate exposure.

→If the copy is too light or too dark even though AUTO was

selected with the [AUTO/TEXT/PHOTO] key

( / / ), adjust the automatic exposure level.

Blank copies.

The original is not placed face up in the SPF or face down

on the document glass.

→Place the original face up in the SPF or face down on the

document glass.

18, 19

Part of the image is cut off or there

is too much blank space.

The original was not placed in the correct position.

→Place the original correctly. 18, 19

An appropriate ratio was not used for the size of the

original and the size of the paper.

→Press the [AUTO IMAGE] key ( ) to have the copy made

using the appropriate ratio for the original and paper.

The size of paper loaded in the tray was changed without

changing the tray's paper size setting.

→Be sure to change the tray's paper size setting whenever you

change the size of paper loaded in the tray.

Wrinkles appear in the paper or

the image disappears in places.

The paper is outside of the specified size and weight

range.

→Use copy paper within the specified range.

Paper curled or damp.

→Do not use curled or crimped paper. Replace with dry copy paper.

During periods when the machine is not used for a long time,

remove the paper from the tray and store it in a dark place in a

bag to prevent moisture absorption.

–

AUTO

AUTO %

AR-5316-5320-EX.book 41 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

Paper misfeed.

Misfeed occurs.

→To remove the misfeed, see "MISFEED REMOVAL". 47

The paper is outside of the specified size and weight

range.

→Use copy paper within the specified range.

Paper curled or damp.

→Do not use curled or crimped paper. Replace with dry copy paper.

During periods when the machine is not used for a long time,

remove the paper from the tray and store it in a dark place in a

bag to prevent moisture absorption.

–

Paper is not loaded properly.

→Make sure the paper is properly installed. 14

Pieces of paper inside machine.

→Remove all pieces of misfed paper. 47

Too much paper is loaded in the tray.

→If the stack of paper is higher than the indicator line on the tray,

remove some of the paper and reload so that the stack does not

exceed the line.

Some sheets of paper stick together.

→Fan the paper well before loading it. 14

The guides on the bypass tray do not match the width of

the paper.

→Adjust the guides to match the width of the paper.

The bypass tray extension is not pulled out.

→When loading a large size of paper, pull out the extension. 15

The bypass paper feed roller is dirty.

→Clean the roller. 57

A5 (5-1/2" x 8-1/2") paper is loaded in lower paper tray.

→A5 (5-1/2" x 8-1/2") size paper must be loaded in upper paper

tray or the bypass tray.

13, 14

Original size not selected

automatically.

(When the SPF is installed.)

Original(s) curled.

→The original size cannot be correctly detected if the original is

curled or folded. Straighten the original.

–

The original includes any large black solid areas.

→If the original includes any large black solid areas, the original

size may not be detected automatically. Use the [ORIGINAL SIZE

ENTER] key ( ) to select the paper size.

–

The machine is directly exposed to sunlight.

→Install in a location that is not exposed to sunlight. –

Problem Cause and solution Page

ENTER

AR-5316-5320-EX.book 42 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

Copies are smudged or dirty.

The document glass or the underside of the document

cover/SPF is dirty.

→Clean regularly.

Original smudged or blotchy.

→Use a clean original. –

White or black lines appear on

copies.

The scanner glass in the SPF is dirty.

→Clean the long, narrow glass in the SPF. 56

The transfer charger is dirty.

→Clean the transfer charger. 57

Paper size for a paper tray cannot

be set.

Copying or printing is performed.

→Set the paper size after copying is complete. –

The machine has stopped temporarily due to running out

of paper or a misfeed.

→Load paper or remove the misfeed, and then set the paper size.

14, 47

An interrupt copy job is in progress.

→Set the paper size after the interrupt copy job is finished. 28

A copy job stops before it is

finished.

The paper output tray is full.

→Long copy runs are automatically paused every 250 copies.

Remove the copies in the paper output tray and press the

[START] key ( ) to resume copying.

The tray is out of paper.

→Load paper. 14

The POWER SAVE indicator ( ) is

lit.

Any other indicators are lit.

→If other indicators are lit, the machine is in "Preheat mode". Press

any key on the operation panel to resume normal operation.

The POWER SAVE indicator ( ) and ON LINE indicator

( ) are only lit.

→If only the POWER SAVE indicator ( ) and ON LINE indicator

( ) are lit, the machine is in auto power shut-off mode. Press

the [START] key ( ) to resume normal operation.

Any one of the alarm indicators

( , , , , ) is lit or

blinking.

See "INDICATORS AND DISPLAY MESSAGES" to check

the meaning of the alarm indicator and error message in

the display, and take appropriate action.

Lighting fixture flickers.

The same power outlet being used is for the lighting

fixture and the machine.

→Connect the machine to a power outlet which is not used for other

electric appliances.

–

Problem Cause and solution Page

AR-5316-5320-EX.book 43 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

PRINTING PROBLEMS

In addition to this section, troubleshooting information can also be found in the README files for each of the

software programs. To view a README file, see the "Software Setup Guide".

Problem Cause and solution Page

The machine does not print.

(ON LINE indicator ( ) does not

blink.)

The machine is set to off-line mode.

→Press the [ON LINE] key ( ) to turn on the ON LINE indicator

().

The machine is not correctly connected with your

computer.

→Check both ends of the printer cable and make sure you have a

solid connection. Try a known good cable. For information on

cables, see "SPECIFICATIONS".

Copy job is performed.

→Wait until the copy job is complete. –

The port setting is not correct.

→Printing is not possible if the printer driver port setting is not

correct. Set the port correctly.

Software

Setup

Guide

Your machine is not selected correctly in the current

application for the print job.

→When choosing "Print" from the "File" menu located in

applications, be sure you have selected "SHARP AR-XXXX"

(where XXXX is the model name of your machine) printer

displayed in the "Print" dialog box.

–

The printer driver has not been installed properly.

→Follow these steps to check and see if the printer driver is

installed.

1 Click the "start" button, click "Control Panel", click "Printers

and Other Hardware", and then click "Printers and Faxes".

(On Windows 95/98/Me/NT 4.0/2000, click the "Start" button,

select "Settings" and then click "Printers".)

2 The "SHARP AR-XXXX" printer driver icon is not shown

(where XXXX is the model name of your machine).

3 If the icon is shown but you still cannot print, the printer driver

may not have been installed correctly. In this case, delete

AR-5316/5320/5316 X/5320 X Software and then reinstall it.

–

The machine does not print.

(ON LINE indicator ( ) was

blinking.)

The tray size settings are not the same on the machine

and in the printer driver.

→Make sure that the same tray paper size is set on the machine

and in the printer driver. To change the tray paper size setting in

the printer driver, see the Software Setup Guide.

Software

Setup

Guide

The specified size of paper has not been loaded.

→Load the specified size of paper in the paper tray. 14

The PAPER SIZE indicator is blinking.

→When "Use close paper size (user program)" is disabled, the

PAPER SIZE indicator on the operation panel will blink. You can

press the [TRAY SELECT] key ( ) to select a tray manually, or

load paper in the bypass tray and press the [ON LINE] key ( ) to

begin printing.

→When "Use close paper size" is enabled, printing will take place

using a size of paper that is close to the size of the print image.

16, 21

–

AR-5316-5320-EX.book 44 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

Removing the software

If you need to remove the software, follow these steps.

Click the "start" button, and then click

"Control Panel".

On Windows 95/98/Me/NT 4.0/2000, click the

"Start" button, select "Settings", and then click

"Control Panel".

2Click "Add or Remove Programs".

On Windows 95/98/Me/NT 4.0/2000, double-click

the "Add/Remove Programs" icon.

3Select "SHARP AR-5316/5320 Series

Printer Driver" from the list, and

remove the software.

For more information, refer to your operating

manual or to the help files for your operating

system.

Printing is slow.

Simultaneous use of two or more application software

programs.

→

Start printing after quitting all unused application software programs.

–

The printed image is light and

uneven.

The paper is loaded so that printing takes place on the

back side of the paper.

→Some paper types have a front and back side. If the paper is

loaded so that printing takes place on the back side, toner will not

adhere well to the paper and a good image will not be obtained.

The printed image is dirty.

You are using paper that is outside the specified size and

weight range.

→Use copy paper within the specified range.

Paper curled or damp.

→Do not use curled or crimped paper. Replace with dry copy paper.

During periods when the machine is not used for a long time,

remove the paper from the tray and store it in a dark place in a

bag to prevent moisture absorption.

–

You did not set sufficient margins in the paper settings of

your application.

→The top and bottom of the paper may be dirty if the margins are

set outside of the specified print quality area.

→Set the margins in the software application within the specified

print quality area.

–

The printed image is skewed or it

runs off the paper.

The paper loaded in the tray is not the same size as that

specified in the printer driver.

→Check if the "Paper Size" options suit the size of the paper loaded

in the tray.

→If the "Fit To Page" setting is activated, make sure that the paper

size selected from the drop-down list of the "Fit To Paper Size"

option is the same as the size of the loaded paper.

–

The orientation of document setting is not correct.

→Click the "Paper" tab in the printer driver setup screen, and verify

if the "Image Orientation" option is set to your requirements.

–

Paper is not loaded properly.

→Make sure the paper is properly loaded. 14

You did not correctly specify the margins for the

application in use.

→Check the layout of the document margins and the paper size

settings for the application you are using. Also check if the print

settings are specified correctly to suit the paper size.

–

Any one of the alarm indicators

(,, , ,) is lit or

blinking.

See "INDICATORS AND DISPLAY MESSAGES" to check

the meaning of the alarm indicator and error message in

the display, and take appropriate action.

Problem Cause and solution Page

AR-5316-5320-EX.book 45 ページ２００３年１１月２６日　水曜日　午後５時３分

INDICATORS AND DISPLAY

MESSAGES

If one of the following indicators lights up or one of the following messages appears in the display, check the

meaning of the indicator or message in the following table and take appropriate action.

Indication Cause and solution Page

Maintenance

indicator

Steadily

lit

Service by an authorised SHARP service technician is

required. –

Developer

replacement

required indicator

Steadily

lit

Developer is required. Contact your authorised service

representative. –

Toner cartridge

replacement

required indicator

Steadily

lit

Replacement of toner cartridge will be needed soon.

Prepare a new cartridge. –

Blinking

Toner cartridge must be replaced. Replace it with a new one.

Paper required

indicator

Steadily

lit

The tray is out of paper. Load paper. It is also possible that

the tray is not inserted completely into the machine. Make

sure it is inserted correctly.

Misfeed indicator Blinking A paper misfeed has occurred. Remove the misfeed as

explained in "MISFEED REMOVAL". 47

ORIGINAL SIZE indicator Blinking

The original is not placed in the correct orientation. Rotate

the original so that it is in the same orientation as the

blinking ORIGINAL SIZE indicator.

18,19

PAPER SIZE indicator Blinking

A blinking PAPER SIZE indicator means that the size of paper

loaded in the tray is different from the paper size setting for the

tray. Change the paper size setting.

To clear the display, do one of the following:

•Use the [TRAY SELECT] key ( ) to change the tray selection.

•Open and close the tray.

•Press the [CLEAR ALL] key ( ).

[CH] appears in display

Steadily

lit

The front cover or the side cover is open. Close the front

cover or the side cover. –

Blinking

The toner cartridge is not installed correctly. Reinstall the

toner cartridge. If [CH] still blinks in the display after

reinstalling the toner cartridge, contact your authorised

service representative.

Letters and numbers appear

in the display

Turn off the power switch, wait about 10 seconds, and then

turn on the switch again. If this does not clear the message,

write down the code that appears and then unplug the

power cord and contact your authorised. Tell service

representative what code appeared and the circumstances

under which it appeared.

–

When "Use close paper size" is disabled

Press the [TRAY SELECT] key ( ) to manually select the

tray and then press the [ON LINE] key ( ). Printing will

begin. If you are selecting the bypass tray, load paper in the

bypass tray.

Online

manual

Misfeed indicator

Paper required indicator

Maintenance indicator

Toner cartridge replacement

required indicator

Developer replacement required indicator

Display

EXTRA

AR-5316-5320-EX.book 46 ページ２００３年１１月２６日　水曜日　午後５時３分

MISFEED REMOVAL

When a misfeed occurs, the misfeed indicator ( ) and a misfeed location indicator ( ) will blink and the machine

will automatically stop.

Check the blinking misfeed location indicator to identify the location of the misfeed and remove it.

MISFEED IN THE SPF

1Remove the misfed original.

Check sections A, B, and

C in the left shows the

illustration (see the next

page), and remove the

misfed original.

Section A

Open the feeding roller cover and remove the

misfed original from the document feeder tray.

Close the feeding roller cover.

Section B

Open the SPF and rotate the two release rollers

in the direction of the arrow to feed the original

out. Close the SPF and then remove the

original.

If a small original (A5 (5-1/2" x 8-1/2"), etc.) is

misfed, open the right side cover and remove

the original. Close the right side cover.

The paper may tear when you remove a misfeed. In this event, be sure to remove all torn pieces of paper from the

machine, taking care not to touch the photoconductive drum (the green part). Any scratches or damage to the

surface of the drum will cause dirty copies.

Note

(p.47)

(p.48)

(p.52)

AR-5320/AR-5320 X

(p.47)

(p.48)

AR-5316/AR-5316 X

Feeding roller cover

Roller

Right side cover

AR-5316-5320-EX.book 47 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

Section C

Remove the misfed original from the exit area.

If the misfed original cannot be easily removed

from the exit area, open the moveable part of the

document feeder tray and remove the original.

2Open and close the SPF to make the

misfeed location indicator stop

blinking.

You can also make the

misfeed indicator stop

blinking by opening and

closing the feeding roller

cover or the right side

cover.

3Return the originals indicated by the

minus number in the display to the

document feeder tray and press the

[START] key ( ).

Copying will resume from the originals that still

remained when the misfeed occurred.

MISFEED IN THE BYPASS TRAY

1Gently pull the misfed paper out. 2Open and close the side cover.

The misfeed indicator

( ) will go out.

•When closing the side cover, press down

on the handle.

•If the misfeed indicator ( ) does not stop

blinking, check for torn pieces of paper in

the machine.

Note

AR-5316-5320-EX.book 48 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

MISFEED IN THE MACHINE

1Open the bypass tray and the side

cover. 2Check the misfeed location. Remove

the misfed paper following the

instructions for each location in the

illustration below.

A. Misfeed in the paper feed area

1Push gently on both ends of the front

cover.

2Carefully remove the misfed paper.

Turn the roller rotating knob in the

direction of the arrow to assist in

removing it.

Be careful not to tear the

misfed paper during

removal.

3Close the front cover and side cover.

The misfeed indicator

( ) will go out.

If paper is misfed here, go to "B.

Misfeed in the fusing area".

If paper is misfed here, go to "A.

Misfeed in the paper feed area".

If the misfed paper is visible

here, go to "C. Misfeed in the

transport area".

The fusing unit is hot. Do not touch

the fusing unit when removing misfed

paper. Doing so may cause a burn or

injury.

Do not touch the photoconductive drum

(green portion) when removing the misfed

paper. Doing so may damage the drum and

cause smudges on copies.

Roller rotating knob

Warning

Caution

•When closing the front cover, gently hold

both ends.

•When closing the side cover, press on the

handle.

•If the misfeed indicator ( ) does not stop

blinking, check for torn pieces of paper in

the machine.

Note

AR-5316-5320-EX.book 49 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

B. Misfeed in the fusing area

1Push gently on both ends of the front

cover.

2Turn the roller rotating knob in the

direction of the arrow.

3Carefully remove the misfed paper.

Lower the fusing unit release levers to

allow easier removal.

Be careful not to tear the

misfed paper during

removal.

4Lift the fusing unit release levers, to

return them to their operating

positions.

5Close the front cover and side cover.

The misfeed indicator

( ) will go out.

The fusing unit is hot. Do not touch

the fusing unit when removing misfed

paper. Doing so may cause a burn or

injury.

•Do not touch the photoconductive drum

(green portion) when removing the misfed

paper. Doing so may damage the drum and

cause smudges on copies.

•Be careful about unfixed toner on the

misfed paper not to soil your hands or

clothes.

Roller rotating knob

Fusing unit

release lever

Warning

Caution

•When closing the front cover, gently hold

both ends.

•When closing the side cover, press on the

handle.

•If the misfeed indicator ( ) does not stop

blinking, check for torn pieces of paper in

the machine.

Note

AR-5316-5320-EX.book 50 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

C. Misfeed in the transport area

1Open the fusing paper guide by

pressing down the projection on

either side of the guide and remove

the misfed paper.

Be careful not to tear the

misfed paper during

removal.

2If the misfed paper cannot be removed

by the previous step but is visible in

the paper output area, remove the

paper by pulling it into the paper

output area.

Be careful not to tear the

misfed paper during

removal.

3Close the side cover.

The misfeed indicator

( ) will go out.

The fusing unit is hot. Do not touch

the fusing unit when removing misfed

paper. Doing so may cause a burn or

injury.

•When closing the side cover, press on the

handle.

•If the paper was torn, make sure that no

torn pieces remain in the machine.

•If the misfeed indicator ( ) does not stop

blinking, check for torn pieces of paper in

the machine.

Warning

Note

AR-5316-5320-EX.book 51 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

MISFEED IN THE UPPER PAPER TRAY

1Lift and pull out the upper paper tray

and remove the misfed paper.

Be careful not to tear the

misfed paper during

removal.

2Open and close the side cover.

The misfeed indicator

( ) will go out.

3Close the upper paper tray.

Push the upper paper

tray in completely.

Make sure that there is no misfed paper in the tray before pulling it out. (p.49)

Note

•When closing the side cover, press on the

handle.

•If the misfeed indicator ( ) does not stop

blinking, check for torn pieces of paper in

the machine.

Note

AR-5316-5320-EX.book 52 ページ２００３年１１月２６日　水曜日　午後５時３分

TROUBLESHOOTING

MISFEED IN THE LOWER PAPER TRAY

(Two-tray model only)

1Open the lower side cover.

Grasp the handle to open

the lower side cover.

2Remove the misfed paper.

Be careful not to tear the

misfed paper during

removal.

3If the misfed paper is not seen in step

2, lift and pull out the lower paper tray

and remove the misfed paper.

Be careful not to tear the

misfed paper during

removal.

4Close the lower side cover.

The misfeed indicator

( ) will go out.

5Close the lower paper tray.

Make sure that there is no misfed paper in the tray before pulling it out. (p.49)

Note

If the misfeed indicator ( ) does not stop

blinking, check for torn pieces of paper in the

machine.

Note

AR-5316-5320-EX.book 53 ページ２００３年１１月２６日　水曜日　午後５時３分

REPLACING THE TONER CARTRIDGE

When the toner cartridge replacement required indicator ( ) lights up, the toner cartridge will need replacement

soon. Obtain a new cartridge. When the toner cartridge replacement required indicator ( ) blinks, the toner

cartridge must be replaced before copying can be resumed.

Replace the toner cartridge by following the procedure below.

1Push on both ends of the front cover

and open it.

2Pull the toner cartridge out while

pressing the lock release lever.

When pulling out the

toner cartridge, place

your other hand on the

green part of the

cartridge.

3Remove the new toner cartridge from

the bag. Grasp the cartridge on both

sides and shake it horizontally four or

five times. After shaking the cartridge,

remove the tape.

4Insert the toner cartridge along the

guides until it locks in place while

pushing the lock release lever.

If there is any dirt or dust

on the toner cartridge,

remove it before

installing the cartridge.

5Remove the tape from the shutter. Pull

the shutter out of the toner cartridge.

Discard the shutter.

6Close the front cover.

The toner cartridge

replacement required

indicator ( ) will go

out.

When the toner cartridge replacement indicator ( ) lights up, little toner remains and thus copies may be faint.

Note

After removing the toner cartridge, do not

shake it or tap on it. Doing so may cause

toner to leak from the cartridge. Put the old

cartridge immediately in the bag contained in

the box of the new cartridge. Dispose of the

old toner cartridge in accordance with local

regulations.

•Grasp the grip when holding the cartridge.

Do not hold the cartridge by the shutter.

•Be sure to shake the cartridge only before

the tape is removed.

Toner cartridge

lock release lever

Caution

Shutter

tape

4 or 5 times

Caution

•Even after a new toner cartridge is installed,

the toner cartridge replacement required

indicator ( ) may still light up, indicating

that copying cannot be resumed (toner is

not fed sufficiently). In this case, open and

close the front cover. The machine will feed

toner again for about two minutes and then

copying can be resumed.

•Before closing the front cover, make sure

that the toner cartridge is correctly installed.

•When closing the front cover, gently hold

both ends.

Note

AR-5316-5320-EX.book 54 ページ２００３年１１月２６日　水曜日　午後５時３分

6Chapter 6

ROUTINE MAINTENANCE

This chapter explains how to keep the machine operating smoothly, including viewing copy count, the toner level

indicator, and cleaning the machine.

CHECKING THE TOTAL OUTPUT

COUNT AND TONER LEVEL

CHECKING THE TOTAL OUTPUT COUNT

From the "0" display, you can check the total output count, total copy count, as explained below.

The total output count is all pages (for both printing and copying) printed by the machine and the total output count

can be counted up to 999,999.

[Total output count]

Hold down the [0] key.

The total output count

appears sequentially in

two parts while you hold

down the [0] key.

Example: Total number of pages output is 12,345.

[Total copy count]

Hold down the [ ] key.

The count display and

counting method are the

same as for the total

output count.

•Each A3 (11" x 17") size page is counted as

two pages.

•During a copy run, pressing the [0] key

shows the number of completed copy

pages, not the total output count.

Note

The total number of pages printed in printer

mode can be calculated by subtracting the

total copy count from the total output count.

Note

AR-5316-5320-EX.book 55 ページ２００３年１１月２６日　水曜日　午後５時３分

ROUTINE MAINTENANCE

CHECKING THE TONER LEVEL

The toner level is indicated by a 6-level display. Use it as a guideline for replacing the toner cartridge.

1Hold down the [Light] key ( ) until

the alarm indicators ( , , , , )

blink.

The display will show

"- -".

Hold down the [Copy ratio display] key

( ) for more than 5 seconds.

The approximate quantity

of toner remaining will be

indicated in the display

as a percentage. ("100",

"75", "50", "25", "10" is

displayed.) When the

percentage is less than

10%, "LO" will be

displayed.

3Press the [Light] key ( ) to return to

the normal display.

The alarm indicators ( , , , , ) go off.

The display returns to the number of copies

display.

ROUTINE MAINTENANCE

CLEANING THE DOCUMENT GLASS AND SPF/

DOCUMENT COVER

If the document glass, SPF, underside of the document cover, or the scanner for originals coming from the SPF (the

long narrow glass surface on the right side of the document glass) become dirty, the dirt may appear on copies.

Always keep these parts clean.

Stains or dirt on the document glass/SPF will also be copied. Wipe the document glass, document cover portion of

the SPF and the scanning window on the document glass with a soft, clean cloth.

If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents.

135

ZOOM

Do not spray flammable cleaner gas. Gas from the spray may come in contact with the internal

electrical components or high-temperature parts of the fusing unit, creating a risk of fire or

electrical shock.

Warning

AR-5316-5320-EX.book 56 ページ２００３年１１月２６日　水曜日　午後５時３分

ROUTINE MAINTENANCE

CLEANING THE BYPASS TRAY PAPER FEED

ROLLER

If misfeeds occur frequently when feeding envelopes, thick paper, etc. through the bypass tray, wipe the paper feed

roller at the feed slot of the bypass tray with a soft, clean cloth dampened with alcohol or water.

CLEANING THE TRANSFER CHARGER

If copies start becoming streaky or blotchy, the transfer charger may be dirty.

Clean the charger using the following procedure.

1Turn the power switch off.

2Open the bypass tray and the side

cover.

3Lift and pull out the upper paper tray.

4Take the charger cleaner out by

holding the tab.

5Set the charger cleaner onto the

transfer charger and gently slide the

cleaner in the direction indicated by

the arrow two or three times.

If the white sheet metal is

smudged with toner,

wipe it with a soft, clean

cloth.

6Return the charger cleaner to its

original position. Close the upper

paper tray. Close the side cover by

pressing the handle on the cover.

7Turn the power switch on.

Paper feed roller

Charger

cleaner

Slide the charger cleaner from one end to the

other end along the groove of the transfer

charger. If the cleaner is stopped on the way,

smudges on copies may occur.

Note

AR-5316-5320-EX.book 57 ページ２００３年１１月２６日　水曜日　午後５時３分

7Chapter 7

PERIPHERAL DEVICES AND SUPPLIES

Optional equipment and supplies are explained in this chapter. To purchase optional equipment and supplies,

contact your authorised service representative.

PERIPHERAL DEVICES

SINGLE PASS FEEDER

For the names of the parts of the SPF, see "PART NAMES AND FUNCTIONS". (p.8)

Specifications

* The detectable original sizes vary by country and region.

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification

changes for product improvement without prior notice. The performance specification figures indicated are nominal

values of production units. There may be some deviations from these values in individual units.

Note

AR-5320/5320 X AR-5316/5316 X

Single pass feeder

(AR-SP6)

AR-SP6 (Single pass feeder)

Acceptable

original

Weight 56 g/m2 to 90 g/m2 (15 lbs. to 24 lbs.)

Size A5 to A3 (5-1/2" x 8-1/2" to 11" x 17")

(5-1/2 x 8-1/2" size originals cannot be used in the duplex copy mode.)

Capacity Up to 40 sheets (Thickness 4 mm (5/32") and below)

For B4 (8-1/2" x 13") and larger sizes, up to 30 sheets

Detectable original

sizes*

A5, A4, A4R, B4, A3

5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13", 8-1/2" x 14", 11" x 17"

Weight 5.0 kg (11.1 lbs.)

Dimensions 583 mm (W) x 435 mm (D) x 133 mm (H)

(22-61/64" (W) x 17-9/64" (D) x 5-1/4" (H))

AR-5316-5320-EX.book 58 ページ２００３年１１月２６日　水曜日　午後５時３分

STORAGE OF SUPPLIES

Standard supplies for this product that are to be replaced by the user are paper and toner cartridge.

PROPER STORAGE

●Store the supplies in a location that is:

clean and dry,

at a stable temperature,

not exposed to direct sunlight.

●Store paper in the wrapper and lying flat.

Paper stored out of the wrapper or in packages

standing on end may curl or get damp, resulting in

paper misfeeds.

For best copying results, be sure to use only SHARP products.

Only genuine SHARP consumables carry the Genuine Supplies label.

GENUINE SUPPLIES

AR-5316-5320-EX.book 59 ページ２００３年１１月２６日　水曜日　午後５時３分

8Chapter 8

APPENDIX

SPECIFICATIONS

Model AR-5316/5316 X AR-5320/5320 X

Type Digital Multifunctional System, Desktop

Photoconductive type OPC drum

Document glass type Fixed

Copy system Dry, electrostatic transfer

Originals Sheets, bound documents

Original sizes Max. A3 (11" x 17")

Copy size

Max. A3 (11" x 17")

Min. A6 (5-1/2" x 8-1/2") (A6 must be fed from the bypass tray)

Image loss: Max. 4 mm (5/32") (leading and trailing edges)

Max. 4 mm (5/32") (along other edges in total)

Copying speed

(one-sided copying at

100% copy ratio)

9 copies/min.

10 copies/min.

11 copies/min.

12 copies/min.

16 copies/min.

A3 (11" x 17")

B4 (8-1/2" x 14")

8-1/2" x 13"

A4R (8-1/2" x 11"R)

A4, A5 (8-1/2" x 11",

5-1/2" x 8-1/2")

10 copies/min.

11 copies/min.

12 copies/min.

14 copies/min.

15 copies/min.

20 copies/min.

11" x 17"

B4 (8-1/2" x 14", 8-1/2" x 13")

A4R

8-1/2" x 11"R

A4, A5 (8-1/2" x 11",

5-1/2" x 8-1/2")

Continuous copy Max. 999 copies; subtractive counter

First-copy time* Approx. 7.2 sec.

Warm-up time* Approx. 45 sec.

Copy ratio

Variable: 25% to 400%, in 1% increments (total 376 steps)

Fixed preset: 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200%

(50%, 64%, 77%, 95%, 100%, 121%, 129%, 141%, 200%)

Exposure system

Document glass: Moving optical source, slit exposure (stationary platen) with

automatic exposure

SPF: Moving original

Paper feed One automatic feeding paper tray (250

sheets) + bypass tray (100 sheets)

Two automatic feeding paper trays (250

sheets each) + bypass tray (100 sheets)

Fusing system Heat rollers

Developing system Magnetic brush development

Light source Cold cathode fluorescent lamp

Resolution Scan: 600 x 300 dpi Output: 600 x 600 dpi (AUTO/TEXT mode)

Scan: 600 x 600 dpi Output: 600 x 600 dpi (PHOTO mode)

Gradation Scanning: 256

Printing: 2 value

Power supply Local voltage ±10% (For this machine’s power supply requirements, see the name

plate located on the back of the machine.)

Power consumption Max. 1.2 kW

Overall dimensions

(with bypass tray folded) 590 mm (W) x 577 mm (D) (23-15/64" (W) x 22-23/32" (D))

AR-5316-5320-EX.book 60 ページ２００３年１１月２６日　水曜日　午後５時３分

APPENDIX

* The first-copy time and warm-up time may vary depending on the power-supply voltage, ambient temperature, and other

operating conditions.

Printer Function

Weight Approx. 31.3 kg (69.1 lbs.)

(Not including toner cartridge)

Approx. 36.3 kg (80.1 lbs.)

(Not including toner cartridge)

Dimensions 590 mm (W) x 577 mm (D) x470 mm (H)

(23-15/64" (W) x 22-23/32" (D) x 18-33/64" (H))

590 mm (W) x 577 mm (D) x555 mm (H)

(23-15/64" (W) x 22-23/32" (D) x 21-55/64" (H))

Operating conditions Temperature: 15°C to 30°C (59°F to 86°F), Humidity: 20% to 85%

Noise level

Sound Power Level LwA(1B=10dB)

Copying: 6.2[B]

Standby: 3.1[B]

Sound Pressure Level LpA (bystander positions)

Copying: 48[dB(A)]

Standby: 16[dB(A)]

Sound Pressure Level LpA (operator position)

Copying: 50[dB(A)]

Standby: 18[dB(A)]

Noise emission measurement in accordance with ISO 7779.

Emission concentration

(measured according to

RAL-UZ62: Edition Jan.

2002)

Ozone: 0.02 mg/m3 or less

Dust: 0.075 mg/m3 or less

Styrene: 0.07 mg/m3 or less

Print speed 12 ppm

Resolution 600 dpi

Memory 16 MB

Emulation SHARP GDI

Interface IEEE1284 parallel connector/

USB connector (USB1.1)

Interface cables

[Parallel cable]

Shielded bi-directional (IEEE1284) cable (max. length 3 m (10 feet))

Please purchase a commercially available parallel cable.

[USB cable (only for connection to USB 1.1 connector)]

Shielded twisted pair cable (max. length 3 m (10 feet))

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification

changes for product improvement without prior notice. The performance specification figures indicated are

nominal values of production units. There may be some deviations from these values in individual units.

Note

AR-5316-5320-EX.book 61 ページ２００３年１１月２６日　水曜日　午後５時３分

SOFTWARE LICENSE

PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE. BY USING THE

SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE.

1. License. The application, demonstration, system and other software accompanying this License,

whether on disk, in read only memory, or on any other media (the "Software") and related documentation

are licensed to you by SHARP. You own the disk on which the Software is recorded but SHARP and/or

SHARP's Licensors retain title to the Software and related documentation. This License allows you to use

the Software on one or more computers connected to a single printer and make one copy of the Software

in machine-readable form for backup purposes only. You must reproduce on such copy the SHARP

and/or its Licensors that were on the original copy of the Software. You may also transfer all your license

rights in the Software, the backup copy of the Software, the related documentation and a copy of this

License to another party, provided the other party reads and agrees to the terms and conditions of this

License.

2. Restrictions. The Software contains copyrighted material, trade secrets and other proprietary material

which is owned by SHARP and/or its Licensors and in order to protect them you may not decompile,

reverse engineer, disassemble or otherwise reduce the Software to a human-perceivable form. You may

not modify, network, rent, lease, loan, distribute or create derivative works based upon the Software in

whole or in part. You may not electronically transmit the Software from one computer to another or over a

network.

3. Termination. This license is effective until terminated. You may terminate this License at any time by

destroying the Software and related documentation and all copies thereof. This License will terminate

immediately without notice from SHARP and/or SHARP's Licensors if you fail to comply with any provision

of this License. Upon termination you must destroy the Software and related documentation and all copies

thereof.

4. Export Law Assurances. You agree and certify that neither the Software nor any other technical data

received from SHARP, nor the direct product thereof, will be exported outside the United States except as

authorized and as permitted by the laws and regulations of the United States. If the Software has been

rightfully obtained by you outside of the United States, you agree that you will not re-export the Software

nor any other technical data received from SHARP, nor the direct product thereof, except as permitted by

the laws and regulations of the United states and the laws and the regulation of the jurisdiction in which

you obtained the Software.

5. Government End Users. If you are acquiring the Software on behalf of any unit or agency of the

United States Government, the following provisions apply. The Government agrees:

(i) if the Software is supplied to the Department of Defense (DoD), the Software is classified as

"Commercial Computer Software" and the Government is acquiring only "restricted rights" in the Software

and its documentation as that term is defined in Clause 252.227-7013 (c)(1) (Oct., 1988) of the DFARS;

and

(ii) if the Software is supplied to any unit or agency of the United States Government other than DoD, the

Government's rights in the Software and its documentation will be as defined in Clause 52.227-19 (c)(2) of

the FAR or, in the case of NASA, in Clause 18-52.227-86 (d) of the NASA Supplement to the FAR.

AR-5316-5320-EX.book 62 ページ２００３年１１月２６日　水曜日　午後５時３分

6. Limited Warranty on Media. SHARP warrants the disks on which the Software is recorded to be free

from defects in materials and workmanship under normal use for a period of ninety (90) days from the

date of purchase as evidenced by a copy of the receipt. The entire liability of SHARP and/or its Licensors

and your exclusive remedy will be replacement of the disk which fails to meet the limited warranty

provided by this Clause 6. A disk will be replaced when it is returned to SHARP or a SHARP authorized

representative with a copy of the receipt. SHARP will have no responsibility to replace a disk damaged by

accident, abuse or misapplication.

ANY IMPLIED WARRANTIES ON THE DISKS, INCLUDING THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO

NINETY (90) DAYS FROM THE DATE OF DELIVERY. THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION

TO JURISDICTION.

7. Disclaimer of Warranty on Software. You expressly acknowledge and agree that use of the Software

is at your sole risk. The Software and related documentation are provided "AS IS" and without warranty of

any kind and SHARP and SHARP's Licensor(s) (for the purpose of provisions 7 and 8, SHARP and

SHARP's Licensor(s) shall be collectively referred to as "SHARP") EXPRESSLY DISCLAIM ALL

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SHARP

DOES NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE SOFTWARE WILL MEET YOUR

REQUIREMENTS, OR THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR

ERROR-FREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED. FURTHERMORE,

SHARP DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE

RESULTS OF THE USE OF THE SOFTWARE OR RELATED DOCUMENTATION IN TERMS OF THEIR

CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. NO ORAL OR WRITTEN

INFORMATION OR ADVICE GIVEN BY SHARP OR A SHARP AUTHORIZED REPRESENTATIVE

SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.

SHOULD THE SOFTWARE PROVE DEFECTIVE, YOU (AND NOT SHARP OR A SHARP

AUTHORIZED REPRESENTATIVE) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING,

REPAIR OR CORRECTION, SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED

WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.

8. Limitation of Liability. UNDER NO CIRCUMSTANCES INCLUDING NEGLIGENCE, SHALL SHARP

BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT

FROM THE USE OR INABILITY TO USE THE SOFTWARE OR RELATED DOCUMENTATION, EVEN IF

SHARP OR A SHARP AUTHORIZED REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY

OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OR EXCLUSION

OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

In no event shall SHARP's total liability to you for all damages, losses, and causes of action (whether in

contract, tort (including negligence) or otherwise) exceed the amount paid by you for the Software.

9. Controlling Law and Severability. For a portion of the Software related with Apple Macintosh and

Microsoft Windows, this license shall be governed by and construed in accordance with the laws of the

state of California and Washington, respectively. If for any reason a court of competent jurisdiction finds

any provision of this License, or portion thereof, to be unenforceable, that provision of the License shall be

enforced to the maximum extent permissible so as to effect the intent of the parties, and the remainder of

this License shall continue in full force and effect.

10. Complete Agreement. This License constitutes the entire agreement between the parties with

respect to the use of the Software and related documentation, and supersedes all prior or

contemporaneous understandings or agreements, written or oral, regarding such subject matter. No

amendment to or modification of this License will be binding unless in writing and signed by a duly

authorized representative of SHARP.

AR-5316-5320-EX.book 63 ページ２００３年１１月２６日　水曜日　午後５時３分

INDEX

Symbols

[] key..........................................................11, 55

About the operation manuals

- Online Manual.....................................................5

- Operation Manual ...............................................5

- Software Setup Guide.........................................5

Adjusting the automatic exposure level....................31

Alarm indicators .........................10, 35, 37, 43, 45, 46

Appendix ..................................................................60

Audible signals ...................................................34, 35

AUDIT CLEAR key.............................................10, 39

Auditing mode ..................................33, 36, 37, 38, 39

Auto clear ...............................................12, 18, 19, 33

AUTO IMAGE indicator ......................................11, 21

AUTO IMAGE key ..............................................11, 21

AUTO PAPER SELECT indicator ......................10, 20

Auto paper select mode ...........................................20

Auto power shut-off mode ..................................12, 33

Auto tray switching .............................................21, 33

AUTO/TEXT/PHOTO key.......................10, 21, 31, 32

Base setting .......................................................34, 35

Basic procedure for printing .....................................29

Before using the machine ..........................................8

Bypass tray ..............................................8, 13, 15, 26

Bypass tray extension ..........................................8, 15

Bypass tray guides...............................................8, 15

Bypass tray paper feed roller ...................................57

Caution

- Cautions on handling ..........................................4

- Cautions on laser ................................................4

- Cautions on using ...............................................3

- Installation site ....................................................3

Changing a tray’s paper size setting ........................16

Charger cleaner ...................................................8, 57

Checking the total output count................................55

Checking the toner level...........................................56

Cleaning

- Bypass tray paper feed roller ............................57

- Document cover................................................56

- Document glass ................................................56

- SPF ...................................................................56

- Transfer charger ...............................................57

CLEAR ALL key .................................................11, 12

CLEAR key...................................................11, 18, 19

Conventions used in this manual ...............................5

Copy functions .........................................................18

Copy ratio display key ............................10, 23, 38, 56

Dark indicator .....................................................10, 21

Dark key .................................................10, 21, 31, 32

Developer replacement required indicator .........10, 46

Differences between models......................................6

Display ........................................................ 10, 39, 46

Document cover ...................................... 8, 18, 20, 56

Document feeder tray.......................................... 9, 19

Document glass ............................................ 8, 18, 56

DUAL PAGE COPY indicator ........................... 10, 27

DUAL PAGE COPY key .................................... 10, 27

Environmental information ........................................ 4

Exit area .................................................................... 9

Feeding roller cover ............................................ 9, 47

Front cover ................................................................ 8

Fusing unit paper guide....................................... 9, 51

Fusing unit release levers ................................... 9, 50

Handles ..................................................................... 8

High image quality mode......................................... 32

Indicators and display messages ............................ 46

Initial settings .......................................................... 12

INTERRUPT indicator ....................................... 10, 28

INTERRUPT key ............................................... 10, 28

Light indicator.................................................... 10, 21

Light key.................................... 10, 21, 31, 32, 35, 37

Loading paper ................................................... 13, 14

Loading the bypass tray .......................................... 15

Loading the paper tray ............................................ 14

Main features ............................................................ 7

Maintenance indicator ....................................... 10, 46

Making a copy darker or lighter ............................... 21

Misfeed indicator ......................................... 10, 46, 47

Misfeed location indicator............................ 11, 46, 47

Misfeed removal

- Bypass tray ...................................................... 48

- Lower paper tray .............................................. 53

- Machine............................................................ 49

- SPF .................................................................. 47

- Upper paper tray .............................................. 52

Normal copying

- Document glass ............................................... 18

- SPF .................................................................. 19

Numeric keys ........................................ 11, 22, 35, 37

ON LINE indicator ............................................. 10, 29

ON LINE key ..................................................... 10, 29

Operation panel................................................... 8, 10

Original guides .................................................... 9, 19

ORIGINAL SIZE ENTER key ...................... 10, 16, 18

ORIGINAL SIZE indicator ................................. 10, 19

AR-5316-5320-EX.book 64 ページ２００３年１１月２６日　水曜日　午後５時３分

Original types

- AUTO ................................................................21

- PHOTO .............................................................21

- TEXT.................................................................21

Paper........................................................................13

Paper feed location indicator..............................11, 16

Paper output tray........................................................8

Paper required indicator...............................10, 13, 46

PAPER SIZE ENTER key ..................................11, 16

PAPER SIZE indicator ...........................11, 16, 18, 19

Paper tray.................................................8, 14, 52, 53

Parallel connector ......................................................9

Part names and functions ..........................................8

Peripheral devices....................................................58

Photoconductive drum ...........................................4, 9

Power .......................................................................12

Power off ..............................................................8, 12

Power on ..............................................................8, 12

POWER SAVE indicator ....................................10, 12

Power save modes...................................................12

Power switch ........................................................8, 12

Preheat mode.....................................................12, 33

PRESET RATIO selector indicator.....................11, 23

PRESET RATIO selector keys.....................11, 23, 24

Printer functions .......................................................29

Reduction/enlargement/zoom

- Automatic ratio selection...................................22

- Manual ratio selection .......................................23

- XY ZOOM copying ............................................24

Removing the document cover ................................20

Replacing the toner cartridge ...................................54

Right side cover ...................................................9, 47

Roller rotating knob ........................................9, 49, 50

Routine maintenance .........................................55, 56

Selecting the tray .....................................................21

Setting the number of copies ...................................22

Side cover ..................................................................8

Side cover handle ......................................................8

Single pass feeder (SPF) .........................................58

Software license.......................................................62

Specifications ...........................................................60

SPF indicator................................................11, 19, 20

START indicator.................................................11, 12

START key.................................11, 12, 18, 19, 35, 37

Storage of supplies ..................................................59

Stream feeding mode.........................................20, 33

Toner cartridge.................................................... 9, 54

Toner cartridge lock release lever ....................... 9, 54

Toner cartridge replacement required indicator

..... 10, 46, 54

Toner save mode .................................................... 32

Total output count ................................................... 55

Transfer charger...................................................... 57

TRAY SELECT key ................... 11, 16, 18, 19, 21, 22

Troubleshooting

- Machine/copying problems .............................. 41

- Printing problems ............................................. 44

Two-sided copying using the bypass tray ............... 26

USB 1.1 connector .................................................... 8

User programs .................................................. 33, 35

User settings ........................................................... 31

Using the manual ...................................................... 5

Using the printer mode ............................................ 29

XY-ZOOM indicator........................................... 10, 24

XY-ZOOM key................................................... 10, 24

ZOOM indicator................................................. 10, 23

Zoom keys................................................... 10, 23, 24

AR-5316-5320-EX.book 65 ページ２００３年１１月２６日　水曜日　午後５時３分

Copying

Automatic ratio selection ..........................................22

Cancelling a copy run.........................................18, 19

Copying, starting ................................................18, 19

Dual page copying .................................................. 27

Enlargement/reduction ............................................ 22

Exposure adjustment .............................................. 21

Exposure selector ................................................... 21

Interrupt copying ..................................................... 28

Manual ratio selection ............................................. 23

Number of copies, setting ....................................... 22

Original cover, removing ......................................... 20

Original size, specifying .......................................... 18

Original, placing

- Document cover................................................18

- SPF ...................................................................19

Tray selection...........................................................21

Two-sided copies using bypass tray ........................26

XY Zoom ..................................................................24

Machine settings

Auditing mode

- Copies, how to make ........................................39

- Setting procedures............................................37

- Settings .............................................................36

Automatic exposure level, setting ............................31

High image quality mode..........................................32

Toner save mode .....................................................32

User programs .........................................................33

- Setting procedures............................................35

- Settings .............................................................33

Problem occurs

Misfeeds

- Bypass tray ...................................................... 48

- Machine (fusing area) ...................................... 49

- Machine (paper feed area)............................... 49

- Machine (transfer area).................................... 51

- SPF .................................................................. 47

- Tray (Lower paper tray).................................... 53

- Tray (Upper paper tray).................................... 52

Troubleshooting ...................................................... 40

Indicators, lit and blinking

[ ] Developer replacement required indicator .... 46

[ ] Maintenance indicator................................... 46

[ ] Misfeed indicator ..................................... 46, 47

[ ] Paper required indicator ......................... 13, 46

[ ] Toner cartridge replacement required

indicator

- Blinking ............................................... 46, 54

- Lit ........................................................ 46, 54

INDEX BY PURPOSE

AR-5316-5320-EX.book 66 ページ２００３年１１月２６日　水曜日　午後５時３分

MEMO

AR-5316-5320-EX.book 67 ページ２００３年１１月２６日　水曜日　午後５時３分

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

CLASS 1

LASER PRODUCT

LASER KLASSE 1

AR-5316-5320-EX.book 68 ページ２００３年１１月２６日　水曜日　午後５時３分

AR-5316-5320-EX.book 1 ページ２００３年１１月２６日　水曜日　午後５時３分

PRINTED IN CHINA

2003M KS

➀

TINSE1152QSZZ

Printed on 100% post-consumer recycled paper

SHARP CORPORATION

AR-5316/AR-5320/AR-5316 X/AR-5320 X

AR-5316-5320-EX.book 1 ページ２００３年１１月２６日　水曜日　午後５時３分

Sharp AR 5316 5316/5320/5316X/5320X Operation Manual GB User To The 28297029 Bea9 4f76 8e91 E8c59bbe5ac6

Navigation menu

Versions of this User Manual:

Views

Navigation