Sharp HRO00052 UPCS Facsimile Equipment User Manual User Manuel
Sharp Corporation UPCS Facsimile Equipment User Manuel
Sharp >
Contents
- 1. User Manuel
- 2. User Manual Addendum
User Manuel
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 698023 |
| Application ID | ig6hyUKjb2HuSKIuehWQ+w== |
| Document Description | User Manuel |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 154.11kB (1926402 bits) |
| Date Submitted | 2006-08-28 00:00:00 |
| Date Available | 2006-08-28 00:00:00 |
| Creation Date | 2006-08-22 17:25:55 |
| Producing Software | Acrobat 5.0 Scan Plug-in for Windows |
| Document Lastmod | 2006-08-22 17:26:57 |
| Document Title | User Manuel |
| Document Creator | Acrobat 5.0 Scan Plug-in for Windows |
MODEL
UX-D1200SE
FACSIMILE
OPERATION MANUAL
WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTICE
FCC Radiation Exposure Statement:
Fax machine: This equipment complies with FCC radiation exposure limits set forth for at uncontrolled
environment. This equipment should be installed and operated with minimum distance at least 20 cm
between the radiator and persons body (excluding extremities: hands, wrists, feet and legs) and must
not be co-located or operated with any other antenna or transmitter.
Cordless handset: For hand held operation, this phone (Cordless Handset) has been tested and
meets the FCC RF exposure guidelines. Use of other accessories may not ensure compliance with
FCC RF exposure guidelines.
ABOUT THE TELEPHONE CONSUMER PROTECTION ACT OF 1991
"The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer
or other electronic device to send any message via a telephone facsimile machine unless such
message clearly contains in a margin at the top or bottom of each transmitted page or on the first page
of the transmission the following information:
(1) The date and time of transmission.
(2) Identification of either the business, business entity or individual sending the message.
(3) Telephone number of either the sending machine, business, business entity or individual.
In order to program this information into your facsimile machine, please refer to the appropriate
instructions in the operation manual."
Declaration of Conformity
SHARP FACSIMILE, UX-D1200SE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-1163
TEL: 800-237-4277
Trademark information
All other company names and product names appearing in this manual are the trademarks of their
respective owners.
This product contains a CR Coin Lithium Battery which contains Perchlorate Material
- special handling may apply, California residents,
See www.dtsc.ca.gov/hazardouswaste/perchlorate/
Table of Contents
Introduction
A Look at the Operation Panel
1. Installation
Unpacking Checklist. . . . . . . . . . . . .
Setup . . . . . . . . . . . . . . . . . . . . . . . .
Loading Paper . . . . . . . . . . . . . . . . .
Connecting the Power Cord . . . . . . .
Installing the Print Cartridge. . . . . . .
Connecting the Phone Line . . . . . . .
Name and Fax Number . . . . . . . . . .
Setting the Date and Time . . . . . . . .
Setting the Reception Mode. . . . . . .
Volume Settings (Machine) . . . . . . .
Cordless Handset Setup . . . . . . . . .
11
11
11
12
13
13
15
15
16
17
17
18
2. Using the Cordless Handset 20
Making Phone Calls . . . . . . . . . . . . .
During a Phone Call . . . . . . . . . . . . .
Using the Intercom Feature . . . . . . .
Using the Phonebook. . . . . . . . . . . .
Call Log . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . .
Ringer Types . . . . . . . . . . . . . . . . . .
Settings . . . . . . . . . . . . . . . . . . . . . .
Register Handset Settings . . . . . . . .
3. Fax to E-mail
Connecting the Machine . . . . . . . . .
E-mail Settings . . . . . . . . . . . . . . . . .
Storing E-mail Addresses. . . . . . . . .
Fax to E-mail Transmission . . . . . . .
Network Settings . . . . . . . . . . . . . . .
4. Sending Faxes
Transmittable Documents . . . . . . . .
Loading the Document . . . . . . . . . . .
Resolution and Contrast. . . . . . . . . .
Sending a Fax: Normal Dialing . . . .
Sending a Fax: Auto Dialing. . . . . . .
20
20
22
23
25
26
30
31
34
39
39
42
44
45
48
49
49
49
50
51
52
Batch Page Numbering. . . . . . . . . . . 56
Sending a Fax From Memory . . . . . . 56
5. Receiving Faxes
57
Using AUTO Mode . . . . . . . . . . . . . . 57
Using MANUAL Mode. . . . . . . . . . . . 57
TEL/FAX Mode . . . . . . . . . . . . . . . . . 58
Reception to Memory . . . . . . . . . . . . 58
6. Making Copies
59
7. Special Functions
60
Broadcasting . . . . . . . . . . . . . . . . . . . 60
Caller ID (Requires Service) . . . . . . 62
Blocking Unwanted Faxes . . . . . . . . 64
Duplex Scanning. . . . . . . . . . . . . . . . 64
Receiving Faxes to E-mail . . . . . . . . 65
Secure Receive. . . . . . . . . . . . . . . . . 67
8. Option Settings and Print
Settings
69
9. Printing Lists
74
Transaction Report . . . . . . . . . . . . . . 75
10. Maintenance
76
Cleaning the Machine . . . . . . . . . . . . 76
Improving Print Quality . . . . . . . . . . . 77
11. Troubleshooting
80
Problems and Solutions . . . . . . . . . . 80
Messages and Signals . . . . . . . . . . . 85
Clearing Paper Jams . . . . . . . . . . . . 88
Ordering Parts. . . . . . . . . . . . . . . . . . 89
Quick Reference Guide
94
Guía de referencia rápida
96
Index
98
Introduction
Machine specifications
Print cartridge yield 1, 2
Replacement cartridge: SHARP UX-C80B
Ink Save mode ON: Approx. 800 letter pages
Ink Save mode OFF: Approx. 480 letter pages
(The initial cartridge has the same yield as the above
replacement cartridge.)
Paper tray capacity
Letter: Approx. 200 sheets (20-lb. copier paper at room
temperature; maximum stack height should not be
higher than the line on the tray)
Legal: 100 sheets
Recommended paper weight: 20-lb. Copy Bond
Recording system
Thermal inkjet
Print resolution
600 × 600 dpi
Effective printing width
8.0" (203 mm) max.
Fax to E-mail
Yes; requires an Internet connection and a router,
switch, or hub to connect the machine. LAN cable
(10Base-T/100Base-TX straight- through cable) must be
purchased separately.
File formats
Tiff (G4), PDF (G4)
Memory capacity 2
Approximately 100 average pages
Modem speed
14,400 bps with auto fallback to lower speeds.
Transmission time 2
Approx. 6 seconds
Compatibility
ITU-T (CCITT) G3 mode
Compression scheme
MR, MH, MMR
Storable transmission
destinations
Rapid Keys: 36
A, B, C keys: 3 (e-mail only)
Speed Dial numbers: 63
Telephone function
Yes (cannot be used if power fails)
Effective scanning width
8.2" (208 mm) max.
Ink Save mode is initially turned off. To turn on Ink Save mode, see pages 69 and 73.
2 Based
on Sharp Standard Chart at standard resolution, excluding time for protocol
signals (i.e., ITU-T phase C time only).
Applicable telephone line
Public switched telephone network
Reception modes
AUTO, MANUAL, TEL/FAX
Automatic document
feeder
Letter/A4: 20 sheets max. (20-lb. paper; temperature: 64
- 82°F (18 - 28°C); humidity: 45 - 65% RH)
Legal: 5 sheets max.
Input document size
Automatic feeding:
Width: 5.8" to 8.5" (148 to 216 mm)
Length (20 sheets): 5.5" to 11" (140 to 279 mm)
Length (5 sheets): 5.5" to 14" (140 to 356 mm)
Manual feeding:
Width: 2.75" to 8.5" (70 to 216 mm)
Length: 5.5" to 14" (140 to 356 mm)
Scanning Resolution
Standard: 203 x 98 dpi
Fine: 203 x 196 dpi
Super fine: 203 x 391 dpi
Halftone: 203 x 196 dpi
Halftone (grayscale)
64 levels
Contrast control
Automatic/Dark selectable
Copy function
Single/Multi/Sort (99 copies/page)
Display
LCD display, 20 digits x 2 lines
Power requirements
120 V AC, 60 Hz
Power consumption
Standby: 6.5 W, Maximum: 40 W
Operating temperature
60 - 90°F (15 - 32°C)
Humidity
25 - 80% RH
Dimensions
(without attachments)
Width: 15.0" (380 mm)
Depth: 11.0" (280 mm)
Height: 6.1" (156 mm)
Weight
(without attachments)
Approx. 9.7 lbs. (4.4 kg)
Cordless handset specifications
Standard
DECT (Digital Enhanced Cordless
Telecommunications)
GAP (Generic Access Profile)
Frequency
1.92 to 1.93 GHz
Duplex operation
TDMA (Time Division Multiple Access)
Dimensions
Width: 2.0" (51 mm)
Depth: 1.2" (30 mm)
Height: 5.5" (140 mm)
Weight (with battery)
Approx. 0.32 lbs. (143 g)
Battery
Rechargeable 1.2 V Ni-MH battery; capacity:
550 mAh x 3 pcs
Power consumption
Initial charging
Approx. 2.0 W (in standby mode)
Approx. 12 hours for initial charge
(24 hours for full charge) (at room temp.)
Max. 15 hours with one full charge (at room temp.)
Max. 120 hours with one full charge (at room temp.)
Talk time
Battery use time in
standby mode
Talk time (and use time in standby mode) may vary
depending on usage, range from base machine, and
environmental conditions such as temperature.
Accessory cordless
handset
UX-K12 (up to 4 handsets can be added)
As a part of our policy of continuous improvement, SHARP reserves the right to make
design and specification changes for product improvement without prior notice. The
performance specification figures indicated are nominal values of production units.
There may be some deviations from these values in individual units.
Important: This machine is not designed for use on a line which has call waiting, call
forwarding, or certain other special services offered by your telephone company (errors
may occur during transmission and reception of faxes).
This machine is not compatible with digital telephone systems.
Important safety information
Do not disassemble this machine or attempt any procedures not described in this
manual. Refer all servicing to qualified service personnel.
Do not install or use the machine near water, or when you are wet. For example, do not
use the machine near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement, or near a swimming pool. Do not spill any liquids on the machine.
Unplug the machine from the power outlet and telephone jack and consult a qualified
service representative if any of the following situations occur:
- Liquid has been spilled into the machine or the machine has been
exposed to rain or water.
- The machine produces odors, smoke, or unusual noises.
- The power cord is frayed or damaged.
- The machine has been dropped or the housing damaged.
Do not allow anything to rest on the power cord, and do not install the machine where
people may walk on the power cord.
This machine must only be connected to a 120 V, 60 Hz, grounded (3-prong) outlet.
Connecting it to any other kind of outlet will damage the machine and invalidate the
warranty.
Never insert objects of any kind into slots or openings on the machine. This could
create a risk of fire or electric shock. If an object falls into the machine that you cannot
remove, unplug the machine and consult a qualified service representative.
Do not place this machine on an unstable cart, stand or table. The machine could be
seriously damaged if it falls.
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations.
Never touch bare telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote risk of electric shock from lightning.
Do not use a telephone to report a gas leak in the vicinity of the leak.
The power outlet must be installed near the equipment and must be easily accessible.
Batteries
Use only the batteries specified in this manual. Use only the provided charger to
charge the batteries.
Do not use new and old batteries together. Do not use different types of batteries
together.
When replacing batteries, make sure that the "+" and "-" sides are placed correctly.
Do not mutilate the batteries. Corrosive fluid may leak out and cause injury or burns to
the eyes and skin. The fluid may be toxic if swallowed. In case of contact with eyes,
flush with clean water (do not rub), and seek medical attention immediately.
Do not store or carry a battery with other metal objects such as keys or pins. These
may short the battery and cause it to overheat.
Do not allow a battery to become wet.
Do not dispose of a battery in a fire or heat a battery. The battery may explode.
Do not let children replace the batteries.
Do not attempt to recharge a non-rechargeable battery.
Health care facilities and equipment
Radio frequency energy emitted from the cordless handset equipment may cause
medical equipment to malfunction. Verify that any personal medical equipment you are
using is adequately shielded from external radio frequency energy before using the
cordless handset equipment. Do not use the cordless handset equipment in health
care facilities where such use is prohibited.
The RBRCTM Battery Recycling Seal on the Nickel-Metal Hydride (Ni-MH) batteries /
battery packs indicates SHARP is voluntarily participating in an industry program to
collect and recycle these batteries /battery packs at the end of their useful life, when
taken out of service in the United States or Canada. The RBRCTM program provides a
convenient alternative to placing Ni-MH batteries into the trash or municipal waste
stream, which is illegal in some areas. Please call 1-800-822-8837 for information on NiMH battery recycling in your area. SHARP’s involvement in this program is part our
commitment to preserving our environment and conserving our natural resources.
(RBRCTM is a trademark of the Rechargeable Battery Recycling Corporation.)
System PIN number
Please fill in your system PIN in the space provided below. For information on the
System PIN number, see page 35.
A Look at the Operation Panel
01
ABC
02
03
04
05
06
07
08
09
10
11
DEF
12
GHI
JKL
MNO
PQRS
TUV
WXYZ
13
14
15
16
17
18
19
20
COPY/HELP
MENU
STOP
RESOLUTION/
RECEPTION MODE
21
UP
SPEED DIAL
22
23
24
25
26
27
28
29
30
31
INTERCOM/
HOLD
32
33/G1
34/G2
35
DEL
REDIAL
36
B'CAST SECURE
DUPLEX
SPEAKER
DOWN
10
11 12
13
14 15 16
17
18
Note: Affix the Rapid Key labels as shown above.
1 Number keys: Use to dial numbers.
8 STOP key: Press to cancel an
operation before it is completed.
2 SCAN TO E-MAIL key: Press to
send a document to an e-mail
recipient.
9 Group Keys: Multiple fax or e-mail
3 Display: This displays messages to
help you operate the machine.
4 A, B, C keys: An e-mail address
can be stored in each key for onetouch selection (p. 44).
5 RESOLUTION/RECEPTION MODE
key: When a document is in the
feeder, press to adjust the scanning
resolution (p. 50). At any other time,
press to select the reception mode
(p. 17).
6 MENU key: Press this key followed
by the arrow keys to select special
functions and settings.
7 COPY/HELP key: When a
document is in the feeder, press to
make a copy (p. 59). At any other
time, press to print the Help List.
destinations can be stored in each
key for one-touch selection (p. 61).
10 Rapid Keys / letter keys: A fax
number or e-mail address can be
stored in each of these keys for onetouch selection (attach the Rapid
Key labels). When entering text, the
keys are used as letter keys.
11 BROADCAST key: Press to send to
multiple fax or e-mail destinations
(p. 60).
12 SECURE key: Press to use the fax
secure receive function (p. 67).
13 DUPLEX key: Use to scan twosided documents for transmission
and copying (p. 64).
14 SPEED DIAL key: Press to select a
fax or e-mail destination stored in a
2-digit Speed Dial number (pp. 44,
52).
15 INTERCOM/HOLD key: Press to
page the cordless handset or to put
a phone call on hold (p. 58).
17 START/MEMORY key: Press after
dialing to send a fax (p. 51). Press
before dialing to send a fax through
memory (p. 56). Press in the date
and time display to show the
percentage of memory currently
used.
16 SPEAKER key: Press to listen to
the line and fax tones through the
speaker when faxing (p. 51).
Note: This is not a speakerphone.
It cannot be used for speaking.
18 Arrow keys: Use to scroll through
and select settings, and to search
for stored destinations (pp.
6 46, 54).
Letter keys
Use these keys when the display prompts you to enter a name, e-mail address,
or other text.
2 3
DEL
B'CAST
SECURE
DUPLEX
16 17
1 SYMBOL key: Press to enter a
symbol (the character appearing on
the right side of each letter key).
Press again to return to normal letter
entry mode.
2 Caps Lock key: Press to enter
upper case letters. Press again to
return to lower case letter entry.
3 SHIFT key: Hold down to
temporarily change case.
4 Letter keys: Use to enter letters.
5 @key, .com key: Press to
conveniently enter “@” and “.com”
when entering an e-mail address.
6 DEL key: Press to delete the
character marked by the cursor.
When the cursor is to the right of a
line of text, press to backspace and
clear characters. (The cursor can be
moved by pressing
or
.) To
delete all entered characters, hold
down until all characters are
cleared.
18
Cordless handset
6 Phonebook key: Press to dial a
number stored in the handset’s
phonebook (p. 23). Hold down to
dial a number stored in the machine.
During a call, press to start fax
reception.
7 Voice box key: You can store the
number of your voice mail service in
this key. To dial the number, simply
hold down the key (p. 32).
11
12
13
14
9 Lock key: Press to lock the keys on
the cordless handset (p. 33).
10 F (flash) key: Use to access special
services from your phone company
that require subscription (contact
your phone company for details).
10
8 Number keys: Use to dial numbers.
15
16
1 Speaker: The other party’s voice is
heard through the speaker.
2 Display: This displays messages to
help you operate the handset.
3 Program keys: Press one of these
keys to select the function that
appears above it in the bottom (left
or right) corner of the display.
4 Power on / Talk key: Press to turn
on the handset power. Press to
make or answer a phone call.
During a call, press to activate
hands-free talking.
11 Arrow keys: Use to navigate
through settings.
12 Off key: Press to end a call. Hold
down to turn off the power.
13 OK key: Use to enter a setting or
access a sub-menu.
14 Redial key: Press to view or dial a
number from the call log (p. 25).
15 INT (Intercom) key: Press to
transfer a call (p. 21) or use the
intercom function (p. 22).
16 Microphone: Speak into this.
5 C (cancel) key
Press to cancel, delete, or return to
the previous menu.
Cordless handset display
am
1 Battery icon: This indicates the
amount of charge in the batteries.
2 Date and time: This shows the date
and time.
3 Left program key function: This
shows which function is selected
when
is pressed (“Alarm” is
shown above as an example).
4 Cordless handset number: This
shows the number that is assigned
to the cordless handset (“1” is
assigned to the cordless handset
that comes with the machine).
5 Right program key function: This
shows which function is selected
when
is pressed (“Mute” is
shown above as an example).
10
Unpacking Checklist
Setup
Paper Document Received
Handset
exit tray
tray
document
cord
tray
Handset
Remove the packing tape
1 Open the cover (➊) and remove the
tape (➋). (Do not install the print
cartridge yet.)
Phone
line
cord
Print
Rapid
cartridge Key
labels
Manual Setup
guide
Cordless Battery Rechargeable Cordless
handset
handset cover
batteries (3)
charger
2 Close the cover.
Selecting a location
♦ To maximize the talking range of the
cordless handset, install the machine
in a high and central location away
from obstructions such as walls.
♦ Keep the machine away from other
Connect the handset
electrical appliances such as TVs,
microwave ovens, computers, and
other cordless phones.
♦ Do not place the machine in direct
sunlight, or near heaters or air
conditioners.
♦ Keep dust away from the machine.
About condensation
If the machine is moved from a cold to a
warm place, condensation may form on the
scanning glass, preventing proper
document scanning. To remove the
condensation, turn on the power and wait
approximately two hours before using the
machine.
Attach the trays
Attach the received
document tray
11
1. Installation
Unpacking Checklist
1. Installation
Loading Paper
Attach the paper tray
Attach the
document exit tray
and flip out the
extension
2 Pull the paper plate forward and
insert the stack of paper into the
tray, print side up.
The stack must
not be higher
than this line
Pull the received document tray
extension all the way out
• If paper remains in the tray, take it
Loading Paper
out and combine it into a single stack
with the new paper.
• Printing on the reverse side of the
Letter or legal size paper can be
loaded.
Maximum number of sheets
(20-Ib. copy bond paper at room
temperature)
Letter: Approx. 200 sheets
(maximum stack height should not be
higher than the line on the tray)
paper may result in poor print quality.
• Do not use paper that has already
been printed on or is curled.
• Remove received faxes and other
printed output before about 50
sheets (10 legal-size sheets)
accumulate in the received
document tray (otherwise the sheets
may scatter).
Legal size: 100 sheets
1 Fan the paper, and then tap the
edges against a flat surface to even
the stack.
12
If you loaded legal size paper...
You must change the “PAPER SIZE”
setting to “LEGAL” (pp. 69 and 73).
(Before changing the setting, plug in
the power cord and install a print
cartridge as explained in the following
sections.)
If at any time the display shows [ADD
PAPER &] / [PRESS START KEY],
check the paper tray. If the tray is
empty, add paper. If there is paper in
the tray, take it out and then reinsert it.
When finished, press
Connecting the Power Cord
Plug the power cord into a 120 V, 60 Hz,
grounded AC (3-prong) outlet.
Caution! Do not plug the power cord
into any other kind of outlet. This will
damage the machine and is not
covered under the warranty.
Caution! Remove all packing tape
before plugging in the power cord
(see page 11), or damage to the
machine may result.
Installing the Print Cartridge
Print cartridge yield
SHARP UX-C80B replacement
cartridge
Ink Save mode OFF:
Approx. 480 letter pages
Ink Save mode ON:
Approx. 800 letter pages
(The initial cartridge has the same
yield as the replacement cartridge.)
♦ Ink Save mode is initially turned off.
To turn on Ink Save mode, see
pages 69 and 73.
Caution! Do not open the cover while
the machine is printing.
Note: Keep print cartridges sealed in
their packages until you are ready to
install them. It is recommended that you
do not use a cartridge that has been left
unused for a long time after opening, as
the print quality may be considerably
degraded.
♦ Make sure the machine’s power cord
is plugged in and paper is loaded in
the paper tray.
The display will show [CHECK
CARTRIDGE] until you install the print
cartridge.
1 Open the cover (grasp the finger
grip).
♦ It is recommended that you install
surge protectors for the power and
telephone lines. Surge protectors can
be purchased at most telephone
specialty stores.
13
1. Installation
Connecting the Power Cord
Installing the Print Cartridge
If the display shows [PRINTER ERROR]
or [PRINTER ERROR/CHECK PAPER],
open the cover and check for jammed
paper. Remove any jammed paper (see
page 88) and close the cover.
4 Insert the new print cartridge (➊).
Close the holder (➋), making sure it
clicks into place.
2 Remove only the
tape from the new
cartridge.
• Make sure all
tape is removed.
• CAUTION!
DO NOT touch
the gold
contact area
on the
cartridge.
5 Close the cover, pressing firmly on
both front corners.
3 Make sure the cartridge holder is in
the position shown. Place your
fingers on top of the holder and
open the holder release.
Display: [CHANGE CARTRIDGE]/
[1=NEW, 2=OLD].
6 Press
(NEW) if the cartridge
you installed is new.
Display: [NEW CARTRIDGE?] /
[OK:PRESS START]
• CAUTION! DO NOT touch the gold
contact area or pull on the cable.
• If you are replacing the cartridge,
remove the old cartridge. If you are
going to use the old cartridge again,
place it in an air-tight container
(containers for this purpose can be
purchased at most office supply
stores).
14
Press
(OLD) if the cartridge
you installed is old.
7 Press
If you selected "OLD" in the
previous step, this completes the
installation procedure. (Note: If you
find that print quality is not
satisfactory, see p. 77 to align the
print cartridge.)
If you selected "NEW", the machine
will print an alignment page.
Continue with the steps below.
8 In the alignment page, locate the
Connecting the Phone Line
TEL. LINE
jack
line that is closest to a straight line.
Standard (RJ-11C) wall jack
In this example, “15” is
closest to a straight line.
9 Enter the number of the straightest
The machine is initially set for tone
dialing. If you are on a pulse dial line,
change the “DIAL MODE” setting (pp.
69 and 70).
line with the number keys.
• To clear a mistake, press
10 Press
Name and Fax Number
Enter your name and fax number.
♦ Your entered name and fax number
The machine is initially set to print
high quality images, which require
more ink. If you prefer to use less ink
and speed up drying time, change the
“INK SAVE MODE” setting to “ON”
(pp. 69 and 73).
will be printed automatically at the top
of all fax pages you send. (This is
required by FCC regulations.)
1 Press
, then
until [ENTRY
MODE] appears.
2 Press
When the resolution is set to HALF
TONE, the machine is initially set to
print at a slower printing speed to
enable higher quality images. When
using HALF TONE, if you prefer faster
printing at the expense of slightly
reduced image quality, change the
“QUALITY MODE” setting to “NO” (pp.
69 and 73).
MENU
Display: [OWN NUMBER SET]
3 Press
[ENTER FAX #]
4 Enter your fax number with the
number keys (max. 20 digits).
• To insert a space, press
• To clear a mistake, press
15
1. Installation
Connecting the Phone Line
Setting the Date and Time
5 Press
3 Press
• The currently set date appears
6 Enter your name using the letter
(example): [DATE 08-15-2006]
keys (max. 24 characters).
Example: SHARP
• To clear a mistake, press
4 Enter a two-digit number for the
month ("01" for January, "02" for
February, "12" for December, etc.).
• For information on using the text
entry keys, see page 8.
7 Press
[DATE&TIME SET]
STOP
8 Press
Example: January
[DATE 01-15-2006]
• To correct a mistake, press
to
move the cursor back to the mistake
and enter the correct number.
5 Enter a two-digit number for the day
to exit.
("01" to "31").
Example: the 5th
[DATE 01-05-2006]
6 Enter the year (4 digits).
Example:
• The currently set time appears
Setting the Date and Time
7 Enter a two-digit number for the
Set the date and time.
♦ The date and time will be printed
automatically at the top of all fax
pages you send (this is required by
FCC regulations). The date and time
also appear in the display.
1 Press
MENU
, then
, then
Example 9:25:
[TIME 09:25 PM]
8 Press
to select A.M. or
to select P.M.
9 Press
until
[DATE&TIME SET] appears.
16
hour ("01" to "12") and a two-digit
number for the minute ("00" to "59").
until [ENTRY
MODE] appears.
2 Press
(example): [TIME 12:19 PM]
STOP
10 Press
to exit.
[ANTI JUNK #]
Setting the Reception Mode
Volume Settings (Machine)
The machine has three modes for
receiving incoming faxes:
Speaker volume
AUTO mode:
The machine automatically answers all
calls on 4 rings and begins fax
reception.
1 Press
MANUAL mode:
All calls, including faxes, must be
answered by picking up the
machine's handset or an extension
phone connected to the same line.
TEL/FAX mode:
The machine automatically answers all
calls on 2 rings. If the machine detects
that a call is a voice call (including a
manually dialed fax), it makes a special
ringing sound to alert you to answer. If
the machine detects that the call is an
automatically dialed fax, it begins
reception automatically.
To set the reception mode, make sure a
document is not loaded in the
document feeder, and then press
RESOLUTION/
RECEPTION MODE
until the desired mode
appears in the display.
For more information on receiving
faxes, see Chapter 5.
SPEAKER
2 Press
or
to select HIGH,
MIDDLE, or LOW.
• Press
SPEAKER
again to turn off the
speaker.
Handset receiver volume
1 When talking through the handset,
press
or
to select HIGH,
MIDDLE, or LOW.
• The volume reverts to MIDDLE each
time you replace the handset.
• During an intercom call, to optimize
the volume of the machine handset
and cordless handset, the volume
setting indicated in the display may
correspond to a different volume
level than for a regular call.
Ringer volume
1 Press
or
to select HIGH,
MIDDLE, LOW, or OFF. (Make sure
SPEAKER
has not been pressed, the
handset is not lifted, and a
document is not loaded in the
feeder.)
• The ringer will ring once at the
selected level.
2 If you selected “OFF OK ?” to turn
off the ringer, press
17
1. Installation
Setting the Reception Mode
Cordless Handset Setup
Cordless Handset Setup
Cordless handset charger
Plug the AC adapter into a standard
120 V AC outlet.
• Important! The dial pad must face
forward, or the batteries will not
charge.
• Let the batteries charge at least 12
hours the first time.
• The cordless handset and charger
may feel warm while charging. This
is normal.
• The batteries charge automatically
Important: Never cover the charger
and AC adapter with a blanket, cloth, or
other material. Excessive heating may
result and cause fire.
Installing the batteries and
charging the cordless handset
♦ Be sure to read the battery
precautions on page 6.
1 Insert the batteries into the cordless
handset, making sure that the "+"
and "-" sides are placed correctly.
Place the battery cover on the
cordless handset.
2 Remove the protective film from the
display, and place the cordless
handset in the charger.
18
while the cordless handset is in the
charger. The battery icon shows the
charging status. When charging is
finished, the battery icon appears
full.
• The batteries cannot be
overcharged. When not using the
cordless handset, keep it in the
charger to ensure that it is always
charged.
• When the batteries need charging,
the battery indicator will blink in the
display and you will hear beeps
during a phone conversation.
Talking range
Large metal objects, metal structures,
thick walls, and other conditions
reduce the talking range. If you hear
noise or interference while talking on
the cordless handset, move closer to
the machine.
Replacing the batteries
Wiping the charger contacts
Hold down
To ensure that the batteries charge
properly, wipe the charger contacts
once a month with a cotton swab.
on the cordless
handset until “POWER OFF” appears in
the display. Press on the indentation on
the back of the handset to remove the
battery cover.
Install the new batteries as explained in
the previous section.
Charger contacts
Important!
Use only the following batteries:
Certified rechargeable AAA batteries,
NiMH 1.2 V, 550 mAh
♦ Using any other type of battery may
damage the cordless handset. Never
use non-rechargeable batteries.
Please purchase the above batteries at
any store that carries rechargeable
batteries.
Caution:
Danger of explosion if batteries are
incorrectly replaced. Replace only with
the above batteries. Dispose of used
batteries according to the instructions
below.
Additional cordless handsets
You can use up to 4 additional UXK12 cordless handsets with the
machine. Additional UX-K12 cordless
handsets can be purchased at your
dealer or retailer. For information on
setting up an additional cordless
handset for use with the machine, see
the manual that accompanies the UXK12 cordless handset.
Battery disposal
The batteries are Nickel Metal Hydride
batteries. The batteries must be
disposed of properly. Contact local
agencies for information on recycling
and disposal plans in your area.
19
1. Installation
Cordless Handset Setup
Making Phone Calls
2. Using the Cordless Handset
Receiving a call
Making Phone Calls
1 When the cordless handset rings,
Making a call
press
1 Enter the phone number with the
number keys.
• If you make a mistake, press C to
clear the mistake.
• If a pause is required between any of
the digits to access a special service
or an outside line, hold down
until a slash (/) appears.
2 Press
to answer.
2 When you are ready to end the call,
press
Note: If you subscribe to a Caller ID
service from your phone company and
have activated the Caller ID function
(see page 62), the name and/or number
of the caller will appear in the display
when you receive a call.
to dial the number.
3 When you are ready to end the call,
press
During a Phone Call
During a phone call, the following
convenient functions can be used:
Note: You can also make a call by
pressing
to access the line. After
To talk without having to hold the
you hear the dial tone, press the
number keys to dial the number.
handset, press
Adjusting the handset volume
To adjust the handset volume during
a phone call, press or .
Turning the cordless handset on
and off
To turn off the cordless handset when
you are not using it (this will save
battery power), hold down
until
“POWER OFF” appears in the display.
To turn on the cordless handset,
press
20
Hands-free mode
during a call and
set the handset down. (You can also
activate hands-free mode by pressing
(MENU),
or
until
“HANDSFREE” appears, and then
(Activ.).)
♦ To adjust the speaker volume, press
or
♦ To turn off hands-free mode, press
again.
Note that this function cannot be used
when the batteries are low.
During a Phone Call
3 When someone answers on a
If you hear a fax tone after answering a
call on the cordless handset, or if the
other party tells you that they would like
to send a fax, press
. This signals
the machine to begin fax reception.
Note: If the machine detects a fax
signal after you answer a call on the
cordless handset, it will begin reception
automatically.
Placing a call on hold
To place a call on hold, hold down C
until “SECRET MODE” (mute) appears.
When this is done, the microphone is
muted so that the other party cannot
hear you. When you are ready to
resume the call, press C again.
Note: You can also place a call on hold
by pressing
(MENU),
or
until
“SECRET” appears, and then
(Activ.). “SECRET MODE” will appear.
To resume the call, press
C.
(Exit) or
To transfer a call to the machine or
another cordless handset (the cordless
handset must be registered in the
machine), follow these steps:
(MENU),
. (You can also press
or until “CALL
TRANSFER” appears, and then
(Valid.).)
2 Press
or to select the device
(select “HANDSET 0” for the
machine), and press
corded handset, press
to
transfer the call.
• If nobody answers, you can return
to the initial caller by pressing
(MENU), or until “HANGING
UP” appears, and then
• If you pressed
(Valid.).
without waiting
for someone to answer and nobody
answers the transfer call for 30
seconds, the cordless handset will
ring to alert you. Press
to
return to the initial caller.
Transferring a call from the
machine’s corded handset
To transfer a call from the machine’s
corded handset to a cordless handset
(the cordless handset must be
registered in the machine), follow
these steps:
1 Press
Transferring a call
1 Press
cordless handset or the machine’s
INTERCOM/
HOLD
on the machine
(“HOLD” will appear in the display),
and then press the number of the
cordless handset to which you wish
to transfer the call. (To page all
cordless handsets, press
.)
(Note that you will not be able to
hear the cordless handset ringing
through the machine handset.)
2 When the other person answers on
the cordless handset, replace the
machine’s corded handset.
(Call).
21
2. Cordless
Handset
Receiving a fax
Using the Intercom Feature
• If nobody answers, press
INTERCOM/
HOLD
. You
can now press the number of a
different cordless handset, or press
INTERCOM/
HOLD
a second time to return to the
1 Press the number of the cordless
handset, or press
for the
machine, and press
initial caller.
You can check a phone number in the
phonebook (page 23) or call log (page
25) during a call.
1 Press
machine), and then press
2 Press
or to scroll through the
entries in the phonebook or calls in
the call log.
Using the Intercom Feature
The machine and cordless handsets
can be used as an intercom system.
♦ To page another cordless handset, it
must be registered in the machine and
be within range of the machine.
♦ It may not be possible to page another
2 The other person answers by
on the paged
3 When you are ready to end the call,
press
Paging a cordless handset from
the machine (cordless handset
locator)
1 Lift the machine handset.
2 Press
INTERCOM/
HOLD
(“HS No.=” appears in
the display) and then press the
number of the cordless handset. (To
page all cordless handsets, press
.)
3 The selected cordless handset
rings. (This allows you to locate the
cordless handset if you have
misplaced it.)
4 The other person answers by
pressing
on the paged
cordless phone.
22
(Call).
cordless phone, or by picking up the
handset on the machine.
(Valid.).
cordless handset or the machine
when the system is already in use.
, press or
to select the device that you wish to
page (select “HANDSET 0” for the
pressing
(MENU), or until
“PHONEBOOK” or “CALLS”
3 When you have finished, press
• You can also press
Checking the phonebook or call
log
appears, and then
Paging the machine or another
cordless handset
Using the Phonebook
5 When you are ready to end the call,
=1
replace the handset.
2. Cordless
Handset
= A, B, C, a, b, c, 2
= D, E, F, d, e, f, 3
= G, H, I, g, h, i, 4
Using the Phonebook
= J, K, L, j, k, l, 5
= M, N, O, m, n, o, 6
You can store your most frequently
dialed numbers for automatic dialing.
Numbers can be stored in the
phonebook in the cordless handset, or
in the machine. To store a number in the
cordless handset, follow the steps
below.
= P, Q, R, S, p, q, r, s, 7
= T, U, V, t, u, v, 8
= W, X, Y, Z, w, x, y, z, 9
= special characters
= /, space, +, @, -, $, &, %, 0
♦ Up to 100 numbers can be stored in
the phonebook in the cordless
handset. Numbers stored in the
cordless handset can only used by the
cordless handset.
♦ To store a number in the machine, see
page 52. The cordless handset can
also use numbers that are stored in
the machine.
Storing phone numbers in the
cordless handset phonebook
1 Press
to open the phonebook.
(You can also press or until
“PHONEBOOK” appears and press
OK.)
2 Press
or to display “”.
(The first time you store a number in
the phonebook, only “”
appears.) Press
(Valid.).
=#,".:;!?'()_
• To clear a mistake, press C.
• To enter a special character, press
, press or until the desired
character is selected, and press OK.
4 When you have finished entering
the name, press
(Valid.).
5 Press the number keys to enter the
phone number. When finished,
press
(Valid.).
• If a pause is required between any of
the digits to access a special service
or an outside line, hold down
until a slash (/) appears.
6 Press
or to select an icon for
the number.
3 Enter the name of the party.
• To enter a letter, repeatedly press the
number key shown for the letter
below until the letter appears.
23
Using the Phonebook
7 Press
(Valid.).
• The entry is stored.
Editing an entry in the
phonebook
1 Press
Using the phonebook to dial a
number
2 Press
1 Press
3 Press
to open the phonebook.
• To open the phonebook in the
machine, hold down
until the
book opens (or you can select
“”
(Valid.).
(Valid.).
Birthday alarm options
Use the birthday alarm options to
select a ring tone for an alarm, or edit
or delete an alarm.
1 Press
or until
“ACCESSORIES” appears and
press OK.
2 Press
or
and press
to select “BIRTHDAY”,
(Valid.).
3 Press
or to select the desired
birthday alarm.
• To show the name, date, and time of
the birthday alarm, press OK.
4 To perform one of the following
actions, press
(Option), press
or to select the action, and
then press
(Valid.).
• VIEW: Select this to view the name,
date, and time of the selected alarm.
• EDIT ENTRY: Select this to edit the
name, date, and time of the selected
alarm.
• DELETE ENTRY: Select this to
delete the selected alarm.
28
(Valid.).
Accessories
change the ring tone used for the
alarm.
• NEW ENTRY: Select this to add a
new alarm.
5 To exit the menu, press
6 Both handsets are now in monitor
mode. Place the sender handset in
the room to be monitored.
♦ The sender handset will not ring to
notify you when a call comes in.
Therefore it can be placed in a room
where someone is sleeping.
♦ Keep the receiver handset with you.
To answer an incoming call on the
Monitoring a room
If you have two cordless handsets (both
cordless handsets must be registered in
the machine), you can use the cordless
handsets to monitor a room, such as a
baby’s room.
One cordless handset will be placed in
the room to be monitored, and will be in
“sender” mode. The other cordless
handset will be kept with you, and will
be in “receiver” mode.
On the “receiver” handset:
1 Press
or until “ACCESSORIES”
appears and press OK.
2 Press
or
to select “ROOM
MONITOR” and press
3 Press
or
(Valid.).
to select the sender
handset and press
(Call).
On the “sender” handset:
4 The sender handset will ring. Press
on the sender handset to
“answer”.
5 The sender handset display will
receiver handset, press
(ACCEPT). At the end of the call, the
handset will automatically return to
monitor mode.
♦ To make a call on the receiver
handset when it is in monitor mode,
press
(Call) and dial the number.
To stop monitoring from the
sender handset
1 Press
(Stop) on the sender
handset.
2 On the receiver handset, press
to return to the standby
display.
To stop monitoring from the
receiver handset
1 Press
(Stop) and then
on the receiver handset.
(Yes)
2 On the sender handset, press
(Stop) to return to the standby
display.
prompt you to activate monitor
mode. Press
(Yes).
29
2. Cordless
Handset
• RINGER TYPE: Select this to
Ringer Types
• KEYTONE: The beeps that sound
Ringer Types
when keys are pressed.
This menu lets you select the ring tones
that signal calls, and activate/deactivate
the beeps that sound on the cordless
handset.
Changing the ring tone (ringer
type)
You can select the ring tones that signal
incoming calls and intercom calls.
1 Press
or until “RINGER TYPE”
appears and press OK.
2 Press
or to select “EXTERNAL
CALL” or “INTERNAL CALL”
(intercom calls), and press
(Valid.).
3 Press
or
4 Press
or
• CHARGER: The beep that sounds
when you place the cordless
handset in the charger.
4 An information screen indicates the
current status of the selected beep
type (“ON” or “OFF”).
• To change the status, press
(Edit). The status changes on the
screen. Press
(Valid.).
• To keep the status, press
5 To exit the menu, press
(Volume).
to select the desired
ringer volume, and press
(Valid.).
5 To exit the menu, press
sound when the battery is low.
(Valid.).
to select the desired
ring tone, and press
• BATTERY LOW: The beeps that
Activating/deactivating silent
mode
Use this setting to turn off all sounds
made by the cordless handset,
including the ringer, beeps, and alarms.
♦ Important: This setting turns off the
Activating/deactivating beeps
1 Press
or until “RINGER TYPE”
appears and press OK.
2 Press
press
3 Press
or
to select “BEEPS” and
(Valid.).
or
to select one of the
following beep types and press
(Valid).
30
alarms of any alarm or timer functions
that you have activated.
1 Press
or until “RINGER TYPE”
appears and press OK.
2 Press
or
to select “SILENT
MODE” and press
3 Press
(Valid.).
(Yes) to activate silent
mode.
4 To exit the menu, press
Settings
to automatically dial the number by
pressing
The “SETTINGS” menu allows you to
customize certain features of the
cordless handset, use security
functions, and register a cordless
handset in a base.
in the standby screen.)
4 Repeat Step 3 to select a function
for the
2. Cordless
Handset
Settings
key.
5 To exit the menu, press
Selecting the program key
functions
This setting allows you to specify which
functions are selected when the
and
keys are pressed in the standby
screen.
1 Press
or until “SETTINGS”
appears and press OK.
2 Press
or
to select “PROGRAM
KEYS” and press
(Valid.).
3 The screen indicates the function
that is currently assigned to the
key.
• To keep the function, press
(Valid.).
Date and time setting
Note: This setting is normally not
necessary, as the date and time that
appear in the cordless handset display
are received automatically from the
machine.
1 Press
or until “SETTINGS”
appears and press OK.
2 Press
or
and press
to select “DATE/TIME”
(Valid.).
3 The screen indicates the currently
set date. Enter the date in MM/DD/
YY format (two digits for the month,
two digits for the day, and two digits
for the year) and press
• To change the function, press
(Edit). Press or to select one of
the following functions:
SILENCE
ALARM
TIMER
KEY LOCK
NUMBER
REDIAL
(Valid.).
4 The screen indicates the currently
set time. Enter the date in HH/MM
format (two digits for the hour and
two digits for the minute), press or
to select A.M. or P.M., and press
(Valid.).
5 To exit the menu, press
After selecting a function, press
(Valid.).
(Note: “NUMBER” is used to store a
number in the
key, allowing you
31
Settings
Auto pickup / auto hang up
1 Press
The “AUTO PICKUP” function allows
you to answer a call by simply lifting the
cordless handset from the charger
2 Press
(without the need to press
3 If a number is already stored, the
).
or until “SETTINGS”
appears and press OK.
or
to select “VOICE BOX
No”, and press
(Valid.).
number will appear.
The “AUTO HANG UP” function allows
you to end a call by simply replacing the
cordless handset in the charger (without
• To keep the current number, press
the need to press
• To set or change the number, press
).
1 Press
or until “SETTINGS”
appears and press OK.
(Edit). Enter the number (press
C if needed to delete digits) and then
press
2 Press
or to select “AUTO
PICKUP” or “AUTO HANG UP”, and
press
(Valid.).
(Valid.).
4 To exit the menu, press
(Valid.).
3 The screen indicates the current
status of the function (on or off).
• To keep the current status, press
(Valid.).
Use this setting to select the language
that is used in the display.
1 Press
or until “SETTINGS”
appears and press OK.
• To change the status, press
(Edit). When the desired status
appears, press
Display language
or
to select
“LANGUAGE”, and press
(Valid.).
(Valid.).
4 To exit the menu, press
2 Press
3 The screen indicates the currently
selected language.
• To keep the current language, press
Voice box number
If you subscribe to a voice mail service
from your phone company, you can use
this setting to store the phone number
of your voice mail service.
♦ Once you have stored the number of
your voice mail service, you can
automatically dial the number by
simply holding down
32
(Valid.).
• To change the language, press
(Edit). Press
or
to select the
desired language, and press
(Valid.). The newly selected
language will appear.
4 To exit the menu, press
Settings
To lock or unlock the keypad, hold down
until the screen indicates that the
You can also lock the keypad using the
“SECURITY” settings.
1 Press
or until “SETTINGS”
appears and press OK.
or
to select “SECURITY”,
and press
3 Press
or
to select “KEYPAD
(Valid.).
4 To lock the keypad, press
(Yes).
Programming an emergency
number
You can program an “emergency”
number. When the number is activated,
it will be automatically dialled when
is pressed.
Note: To dial regular calls using the
keypad after the emergency number
has been programmed and activated,
you must first enter the number with the
number keys and then press
cannot be pressed before
entering a number).
1 Press
3 Press
or
to select “SECURITY”
(Valid.).
to select
4 The screen indicates the currently
programmed emergency number
and its status (activated or
deactivated).
• To keep the current number and
status, press
(Valid.).
LOCK” and press
or
and press
“EMERGENCY” and press
(Valid.).
keypad is locked or unlocked.
2 Press
2 Press
2. Cordless
Handset
Locking/unlocking the keypad
or until “SETTINGS”
appears and press OK.
(Valid.).
• To change the number or status,
press
(Edit).
Press or to select one of the
following actions:
ACTIVATE: Select this to activate
the number. Press
(Valid.).
DEACTIVATE: Select this to
deactivate the number. Press
(Valid.).
CHANGE NO: Select this to change
the number. Press
(Valid.), enter
the desired number with the number
keys (or press
and select a
number in the phonebook),
and then press
(Valid.) again.
Note that when you change the
number, it is automatically activated.
5 To exit the menu, press
• When the emergency number is
activated, “EMERGENCY” appears
in the message area of the display.
33
Register Handset Settings
Register Handset Settings
4 Select “REGISTRATION” and press
(Valid.).
In order to be used, a cordless handset
must first be registered in the machine
(the base). The cordless handset that
came with the machine is already
registered. To register an additional
cordless handset, follow the steps
below.
♦ If the system PIN number has been
changed to a number other than
“0000” in the machine (see page 35),
or if you are registering the cordless
handset in more than one base, you
must use the personal registration
procedure on page 35 to register the
cordless handset.
♦ A cordless handset can be registered
in up to four bases. To register the
cordless handset in multiple bases,
repeat the personal registration
procedure on page 35 using each
base. To select which base the
cordless handset will normally be
used with, see page 37.
Registering a cordless handset
(regular procedure)
On the cordless handset
1 Press
or until “SETTINGS”
appears and press OK.
2 Press
or
to select “ADVANCED
SET.” and press
3 Press
or
(Valid.).
to select “SET
HANDSET” and press
34
(Valid.).
5 Press
(Yes). The handset enters
registration mode.
On the machine (the base)
1 Press
MENU
, then
until
[REGISTER HS SETTING] appears.
2 Press
twice.
3 Press
• The display will show [WAITING HS
ENTRY] while the machine
communicates with the cordless
handset. When registration is
finished, [HSX REGISTERED] will
appear, where “X” is the number of
the newly registered handset.
• If registration fails, [ABORT HS
ENTRY] will appear.
Register Handset Settings
The system PIN is a 4-digit ID number
that is used to prevent unauthorized
registration of a cordless handset in the
machine. When the system PIN is set to
a number other than 0000 (the initial
factory setting), a cordless handset
must be registered using the personal
registration procedure and the correct
system PIN must be entered on the
cordless handset during registration.
Follow these steps to program a system
PIN in the machine.
1 Press
MENU
, then
until
[REGISTER HS SETTING] appears.
2 Press
, then
until [SYSTEM
Registering a cordless handset
(personal registration)
Use this procedure to register a
cordless handset in the following cases:
♦ The system PIN has been changed to
a number other than “0000”.
♦ You are registering the handset in
multiple bases.
♦ You want to choose the number that is
assigned to the cordless handset.
♦ You want to assign a name to the
base (the machine). This name
appears when you press the OK key
in the standby screen.
On the cordless handset
PIN] appears.
3 Press
1 Press
or until “SETTINGS”
appears and press OK.
4 Enter the current system PIN (4
digits).
2 Press
or
to select “ADVANCED
SET.” and press
• The system PIN is initially set to
0000 at the factory.
5 Press
6 Enter the new system PIN that you
wish to use (4 digits).
7 Press
8 Enter the new system PIN once
again for confirmation.
9 Press
3 Press
or
(Valid.).
to select “SET
HANDSET” and press
(Valid.).
4 Select “PERSON. REGISTR” and
press
(Valid.).
5 Enter the number (1 to 4) that you
would like to assign to the machine
and press
(Valid.).
• This number is used to identify the
machine when the cordless handset
is registered in multiple bases.
STOP
10 Press
to exit.
35
2. Cordless
Handset
Programming a system PIN
Register Handset Settings
6 The current base name appears. If
desired, you can press C to delete
the old base name and then enter a
new name (see Step 3 on page 23).
When the desired name appears,
press
(Valid.).
7 Enter the system PIN (4 digits) of
the machine (see page 35). Press
(Valid.).
• The handset enters registration
mode.
♦ Perform the following steps on the
machine.
1 Press
MENU
, then
until
2 Press
, then
until
[HS DELETE] appears.
MENU
, then
until
[REGISTER HS SETTING] appears.
2 Press
To delete the registration of a cordless
handset from the machine, follow the
steps below. This procedure can be
used if you need to disable a cordless
handset.
[REGISTER HS SETTING] appears.
On the machine (the base)
1 Press
Deleting a cordless handset
twice.
3 Press
4 Enter the number of the handset (1
to 5) that you wish to delete.
3 Press
• Registration begins.
On the cordless handset
1 When the cordless handset display
indicates that registration is finished,
enter the number from 1 to 5 that
you would like to assign to the
handset.
• A number that is already assigned to
another cordless handset cannot be
used.
36
5 Press
6 Enter the system PIN (4 digits) of
the machine (see page 35; if the
system PIN has not been changed
from the intial factory-set PIN, enter
“0000”).
7 Press
to delete the handset.
STOP
8 Press
to exit.
Register Handset Settings
If you prefer that the cordless handset
not be used to start fax reception, follow
the steps below to change the remote
fax reception setting to NO.
♦ Perform the following steps on the
machine.
1 Press
MENU
, then
until
[REGISTER HS SETTING] appears.
2 Press
, then
until
[REMOTE FAX RX] appears.
3 To allow remote fax reception, press
(“YES”). To prohibit remote fax
reception, press
If you have used the personal
registration procedure to register the
cordless handset in more than one
base, the following procedure can be
used to select which base the cordless
handset normally uses.
♦ The initial setting is auto. When auto
is selected (or when the selected
base is not powered on), the cordless
handset uses the first base that is
powered on.
1 Press
or until “SETTINGS”
appears and press OK.
2 Press
or
to select “ADVANCED
SET.” and press
3 Press
or
(Valid.).
to select “SET
HANDSET” and press
STOP
4 Press
(“NO”).
Giving priority to a base
to exit.
4 Press
or
(Valid.).
to select “BASE
PRIORITY” and press
(Valid.).
5 The screen indicates the current
base priority setting.
• To keep the current setting, press
(Valid.).
• To change the setting, press
(Edit). Press or to select
“AUTO” or the desired base (each
base is identified by the number
assigned in Step 5 of the personal
registration procedure), and press
(Valid.).
6 To exit the menu, press
37
2. Cordless
Handset
Disabling fax reception from the
cordless handset
Register Handset Settings
Resetting the handset
Renaming the base
This procedure can be used to reset the
settings on the cordless handset to the
intial (factory default) settings.
To change the name of the base that
appears when you press the OK key in
the standby screen, follow the steps
below.
♦ All settings are reset except for
1 Press
or until “SETTINGS”
appears and press OK.
phonebook entries.
1 Press
or until “SETTINGS”
appears and press OK.
2 Press
or
to select “ADVANCED
SET.” and press
3 Press
or
4 Press
or
5 Press
(Valid.).
to select “RESET
(Valid.).
(Yes) to reset the settings.
6 To exit the menu, press
or
and press
to select “SET
HANDSET” and press
or
to select “ADVANCED
SET.” and press
3 Press
(Valid.).
HANDSET” and press
2 Press
4 Press
or
to select “SET BASE”,
(Valid.).
to select “RENAME
BASE” and press
5 Press
or
(Valid.).
(Valid.).
to select the base that
you wish to rename and press
(Valid.).
6 Enter the new name using the
numeric keys (see Step 3 on page
23). When finished, press
(Valid.).
7 To exit the menu, press
38
3. Fax to E-mail
The Fax to E-mail feature lets you scan
a document and directly send the image
to an e-mail recipient.
♦ This saves you the trouble of scanning
the document into a computer and
sending the scanned file using an email program.
♦ The scanned document is sent as an
Connecting the Machine
Connecting the Machine
The machine is connected using an
Ethernet cable (not included). Please
purchase a 10Base-T/100Base-TX
straight-through (regular) cable.
Connect one end of the cable to the
LAN port on the machine.
3. Fax to
E-mail
attachment to an e-mail message.
The attached file can be in TIFF or
PDF format.
Requirements
To use Fax to E-mail, you must
♦ Have a broadband (cable or DSL)
Internet connection.
♦ Have a broadband router or LAN
switch/hub through which you can
connect the machine to the Internet
(the router is usually connected to a
cable modem or DSL modem).
A typical setup is shown below.
Connect the other end to a LAN port on
your router, switch, or hub.
♦ If you are uncertain which port to
connect the cable to, see the manual
for the router, switch or hub.
♦ The connections can be made with all
devices powered on.
WAN port
Internet
Cable/DSL
modem
LAN cable
LAN cable
LAN ports
(Hub/Switch)
LAN cable
Router
♦ For other questions about how the
machine should be connected,
consult your Internet service provider.
LAN cable
39
Connecting the Machine
IP address
3 Press
The machine requires an IP address to
communicate on the Internet.
If your network is set up to
automatically assign IP addresses, you
do not need to do anything; the
machine will automatically receive an
IP address when it is connected.
• If the machine has automatically
received an IP address and is able
to communicate, [IP ADDRESS/
DHCP: ON] will appear on the top
line of the display, followed by the IP
address on the bottom line. To show
the machine’s host name, press
Automatic assignment of IP addresses
is normally performed by a DHCP
server, which may be a computer,
router, or other device on the network.
(Most routers used on home networks
contain a DHCP server.)
If your network requires that a static
(permanent) IP address be assigned to
the machine, see Network Settings on
page 48 to enter the IP address and
related information.
Checking your IP address and
the connection
To check the machine’s IP address and
verify that the machine is able to
communicate on the network, follow
these steps.
1 Press
MENU
, then
until
[NETWORK SETTING] appears.
2 Press
, then
to show
[NETWORK INFORMATION]
• If a static IP address has been
entered in the machine and the
machine is able to communicate,
[IP ADDRESS/DHCP: OFF] will
appear on the top line of the display,
followed by the IP address on the
bottom line. To show the machine’s
host name, press
• If the machine was unable to
receive an IP address automatically,
or if the router locked up after the
machine received an IP address,
[IP ADDRESS/DHCP: FAIL] /
[192.168. 1 .201] will appear.
“192.168. 1 .201“ is an IP address
that is assigned to the machine for
diagnostic purposes when
connection fails (it cannot be used
for regular communication).
• If a cable has not been connected,
[CHECK CABLE] will appear.
• If [NOW CONNECTING / CHECK
STOP
LATER] appears, press
to exit,
wait briefly, and then repeat the
procedure again.
40
Connecting the Machine
♦ Check the Ethernet cable. Are the
connections secure? Are you using
straight-through (not crossover) cable
for 10Base-T/100Base-TX?
♦ There may be a problem in the router
or other device to which the machine
is connected. Try removing and then
restoring the power to the router (see
the manual for the router).
♦ If [IP ADDRESS/DHCP: FAIL]
appears, remove and then reinsert
the Ethernet cable plug, and repeat
Steps 1 to 3 above. If the same
message appears, check the device
that acts as the DHCP server on your
network (try removing and restoring
the power). If your router is your
DHCP server, make sure that DHCP
is enabled in the router settings. If
your network does not have a DHCP
server, set a static IP address as
explained on page 48.
♦ If a static IP address has been set,
make sure that the network settings
(page 48) are correct .
41
3. Fax to
E-mail
If the machine is unable to
communicate...
E-mail Settings
E-mail Settings
Before the Fax to E-mail function can be
used, you must configure the e-mail
settings.
The e-mail settings specify your
outgoing mail server, as well as your
sender name, sender address, and
other items that appear in the e-mail
message to which scanned image files
are attached.
♦ It is easiest to configure the e-mail
settings in the machine’s Web page.
The machine’s Web page can be
accessed from any computer on the
same network as the machine.
♦ The e-mail settings can also be
configured using the machine’s
operation panel.
Note: If you need to configure “POP
before SMTP” settings, you must use
the Web page.
If you do not know your SMTP server
name or whether or not you need to
configure “POP before SMTP” settings,
ask your Internet service provider.
Accessing the machine’s Web
page
To access the Web page, you will need
to know the machine’s host name or IP
address (usually it is most convenient to
use the host name).
To check the machine’s host name or IP
address, follow the procedure in
Checking your IP address and the
connection (page 40), or print the
Network Settings List (page 74).
42
Type in the host name or IP address of
the machine in the Address bar of the
Web browser on your computer.
The Web page menu will appear. Select
E-mail Setup and configure the
settings. For explanations of the
settings, click Help in the Web page
menu.
Note: If the Web page is used while the
machine is in operation (except for
voice calls using the handset), machine
operation may become unstable.
Using the machine’s operation
panel to configure the settings
Follow the steps below to display the email settings, and then configure each
setting as explained in the table on the
next page.
1 Press
MENU
, then
until
[E-MAIL SETTING] appears.
2 Press
, then
repeatedly until
the setting that you wish to
configure appears.
3 Press
. (Note: This step is not
necessary for the “FILE FORMAT”
setting.)
4 Enter the required information for
the setting as explained in the table
on the next page.
5 After configuring the setting, the
next e-mail setting will appear in the
display. You can configure the next
STOP
setting, or press
to exit.
E-mail Settings
E-mail settings
Enter the required information for each setting as explained below.
This is done in step 4 of the procedure on the previous page.
♦ The sender address and SMTP server settings are required. The other settings are
optional.
♦ Use the letter keys to enter text. For information on using the letter keys, see page 8.
♦ The e-mail subject, e-mail message, and file format that you enter below are default
3. Fax to
E-mail
settings. They will be used if you do not specify these items at the time of
transmission.
Setting
Description
SENDER
NAME
Enter the sender name that will appear in the e-mail message
SENDER
ADDRESS
Enter your sender e-mail address (max. of 128 characters). When
(max. of 50 characters). When finished, press
finished, press
. (Note: Be sure to enter your actual e-mail
address. Return e-mail and undelivered mail reports will be sent to
this address. In addition, some SMTP servers reject outgoing email if a valid sender e-mail address is not entered.)
E-MAIL
SUBJECT
Enter a default subject (max. of 128 characters). When finished,
E-MAIL
MESSAGE
Enter a default message (max. of 256 characters). When finished,
FILE FORMAT
This sets the default format of the file that is created when you
press
press
scan a document. Press
Initial setting: TIFF
SMTP SERVER
for TIFF or
for PDF.
Enter the host name or IP address of your outgoing (SMTP) mail
server (max. of 60 characters). When finished, press
43
Storing E-mail Addresses
Storing E-mail Addresses
You can store e-mail addresses in the
A, B, and C keys, in Rapid Keys, and in
Speed Dial numbers.
♦ An e-mail address stored in a Rapid
Key or the A, B, or C key is selected
by simply pressing that key. A total of
36 Rapid Keys are available.
(Note: Attach the Rapid Key labels as
shown on page 7.)
♦ An e-mail address stored in a Speed
Dial number is selected by pressing
SPEED DIAL
and entering the 2-digit Speed
Dial number. A total of 63 Speed Dial
numbers are available.
Note: Rapid Keys and Speed Dial
numbers are also used for fax (p. 52).
Storing an e-mail address
Follow the steps below to store an email address using the machine’s
operation panel.
♦ E-mail addresses can also be stored
using the machine’s Web page. To
access the Web page, see page 42.
1 Press
MENU
, then
2 To store an e-mail address in the A,
B, or C key, press the desired key
and go directly to Step 4.
To store an e-mail address in a
Rapid Key, press the desired Rapid
Key.
To store an e-mail address in a
44
• If you prefer to have the machine
suggest an available Rapid Key /
Speed Dial number at the end of the
procedure, press
3 Press
to select E-MAIL.
Display: [E-MAIL # MODE]
4 Enter the e-mail address with the
letter and number keys (max. of 128
characters).
• For information on using the letter
keys, see page 8.
• To clear a mistake, press
5 Press
6 Enter the name of the recipient
(max. 20 characters).
7 Press
• If you selected a Rapid Key or
Speed Dial number in Step 2, the
display will briefly show [STORED],
and then [NEW NUMBER]. Go to
Step 8.
• If you did not select a Rapid Key or
Speed Dial number, press
and enter the desired 2-digit
number (01 to 63).
SPEED DIAL
Speed Dial number in Step 2, the
display will show the next available
Rapid Key or Speed Dial number. If
that number is acceptable, press
and go to Step 8. If not, press
the desired Rapid Key, or press the
A, B, or C key, or press
SPEED DIAL
and
enter the desired 2-digit Speed Dial
number, and go to Step 8.
Fax to E-mail Transmission
8 Return to Step 2 to store another eto exit.
Editing and clearing stored email addresses
To make changes to a previously stored
e-mail address, or to clear an address,
follow these steps:
1 Press
MENU
, then
• If you do not wish to change the
name, go directly to Step 7.
7 Press
8 Return to Step 2 to edit or clear
STOP
another address, or press
exit.
to
3. Fax to
E-mail
mail address, or press
6 Make the desired changes to the
name.
STOP
2 Press the key in which the address
is stored (Rapid Key or A, B, or C
key), or press
SPEED DIAL
and enter the
2-digit Speed Dial number in which
the address is stored.
(You can also press
or
until
the name or address appears and
press
.)
Display: [1=EDIT, 2=CLEAR]
3 Press
for EDIT or
Fax to E-mail Transmission
Follow the steps below to send a
document to an e-mail recipient.
♦ The document will be sent as an
attachment to an e-mail message.
for
CLEAR.
• If you selected CLEAR, go to Step 8.
4 If you selected EDIT, make the
desired changes to the address.
• Press
or
to move the cursor
to the character(s) you wish to
change, and then press the
appropriate letter or number key. The
new character will replace the old
character.
• If you do not wish to change the
♦ You can specify the recipient by
directly entering an e-mail address, or
by selecting an address that has been
stored as explained in the previous
section.
1 Flip up the feeder cover (➊) and
adjust the document guides to the
width of your document (➋).
address, go directly to Step 5.
5 Press
45
Fax to E-mail Transmission
2 Insert the
appears, your SMTP server or
sender address has not been
entered in the e-mail settings (p. 42).
document
face down
with the top
edge going
in first.
4 If you need to select or change any
of the e-mail options, press
• Up to 20 letter-size sheets (5 legalsize sheets) can be placed in the
feeder at once.
• For more information on loading the
document, see page 49.
• If desired, press
RESOLUTION/
RECEPTION MODE
• To exit the e-mail options, press
to set the
resolution and contrast (see p. 50).
3 Enter the destination e-mail address
using one of the following methods:
• Press
, press
and enter the address with the letter
and number keys (p. 8). When
finished, press
• If the address has been stored in the
A, B, or C key, press the key.
• If the address has been stored in a
Rapid Key, press the Rapid Key.
• If the address has been stored in a
Speed Dial number, press
SPEED DIAL
and enter the Speed Dial number.
• To search for a stored address, press
(this eliminates
stored fax numbers from the search),
press
or
until the name or
address appears, and press
Note: If [CHECK E-MAIL SETTING]
46
and follow Steps
5 and 6 below. (Note that settings
selected here are temporary. To
make permanent changes, see p.
42.)
If you do not wish to change the email options, go directly to Step 7.
and go to Step 7.
5 Press
or
until the desired
option appears, and press
is not necessary for the FILE
FORMAT setting). Change the
option as explained below (use the
letter keys to enter text and
to delete text; p. 8).
• E-MAIL SUBJECT: Enter a subject
(max. 128 characters). When
finished, press
• E-MAIL MESSAGE: Enter a
message (max. 256 characters).
When finished, press
• FILE FORMAT: Press
for TIFF
or
for PDF. (Make sure the
recipient has an image viewer that
can show images in the selected
format.)
• FILE NAME: Enter a name for the
scanned file (max. 40 characters).
Fax to E-mail Transmission
(If a file name is not entered, the
name “UXB800-yymmddhhmmss”,
where “yymmddhhmmss” is the
year, month, day, hour, minute, and
second the file was created, is
automatically assigned.)
6 When you have finished configuring
the e-mail options, press
. (If the display
shows [PRESS START TO SCAN],
it is not necessary to press
.)
7 Press
to begin transmission.
Note: The recipient may have security
settings in their e-mail program or virus
protection software that prevent the file
attachment from being received or
opened. In this case, ask the recipient
to try changing the settings.
Sending a message only
You can also send a short e-mail
message without including a
document. Perform Steps 3 through 7
of the above procedure (enter the
message in Step 5). After Step 7,
[SEND W/O DOCUMENT?] /
[1=YES,2=NO,W/T DOC.]
will appear. Press
to select
“YES”. The message will be sent.
Error messages
If transmission is not successful
because the machine is unable to
connect to your mail server, one of the
following error messages will appear.
[CONNECTION ERROR]
This appears when communication
does not take place correctly on your
local network, usually due to a problem
with the cable connections. Make sure
that the cable ends are securely
inserted in the LAN ports. Make sure
that the correct cable is being used and
that the cable is good. Make sure that
your router or hub is powered on.
[SERVER ERROR]
This appears when the machine cannot
connect to your mail server or there is
no response from the mail server.
Make sure the SMTP server setting is
correct (p. 43). If you have configured
“POP before SMTP” settings in the
Web pages, make sure these settings
are correct.
[SERVER NOT FOUND] / [SMTP]
This appears when an incorrect host
name is entered for your SMTP server.
Check the SMTP server setting (p. 43).
[SERVER NOT FOUND] / [DHCP]
This appears when the machine is
unable to automatically obtain an IP
address. Restart your router or other
device that acts as your DHCP server.
[CABLE DISCONNECTED]
This may appear below any of the
above messages. Check the same
items as in [CONNECTION ERROR]
above.
If an undelivered mail report is sent
to inform you that your e-mail
message was not successfully
delivered, the report will be sent to
the sender address entered in the email settings (page 42).
47
3. Fax to
E-mail
When finished, press
Network Settings
Network Settings
If your network requires that you assign
a static (permanent) IP address to the
machine, follow the steps below to
disable DHCP (automatic IP address
assigment) and configure the network
settings.
• Consult your network administrator
for the information that must be
entered. After DHCP is disabled, the
settings that must be configured
appear in the following order (these
settings only appear when DHCP is
set to NO):
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
DNS (PRIMARY)
DNS (SECONDARY)
1 Press
MENU
, then
until
[NETWORK SETTING] appears.
twice.
[DHCP] will appear.
for NO (the machine will
not obtain an IP address
automatically).
• [IP ADDRESS] will appear.
(If you wish to configure a different
4 Press
.)
5 Press the number keys to enter the
required number.
• Three digits must be entered in each
segment of the number (the
48
to
move the cursor to the mistake and
enter the correct number.
6 When finished entering the number,
press
7 The next setting will appear in the
display. Repeat Steps 4 through 6
to configure the next setting, or
STOP
press
to exit.
Initializing the network settings
If you need to return the network
settings to their initial state, follow the
steps below.
DHCP and clears the IP address
and related settings.
3 Press
or
• If you make a mistake, press
• Initializing the settings enables
2 Press
setting, press
segments are separated by
periods). If a segment does not have
3 digits, enter zeros as needed.
Example: IP address = 192.168.1.2
You must enter: 192.168.001.002
1 Press
MENU
, then
until
[NETWORK SETTING] appears.
2 Press
twice, then
[INITIALIZE SETTINGS].
3 Press
twice.
to show
Transmittable Documents
Minimum document size/weight
Loading up to 20 sheets at once:
5.8” x 5.5” (148 x 140 mm)
14 lbs. (52 g/m2)
Loading 1 sheet at a time:
2.8” x 5.5” (70 x 140 mm)
14 lbs. (52 g/m2)
Maximum document size/weight
Loading up to 20 sheets at once:
Letter (8.5” x 11”, 216 x 279 mm)
20 lbs. (75 g/m2)
Loading up to 5 sheets at once:
Legal (8.5” x 14”, 216 x 356 mm)
20 lbs. (75 g/m2)
Loading 1 sheet at a time:
Legal (8.5” x 14”, 216 x 356 mm)
42 lbs. (157 g/m2)
The maximum scanning width is 8.2”
(208 mm), and the top and bottom
0.16” (4 mm) of a document cannot
be scanned.
Other restrictions
♦ The scanner cannot recognize yellow,
greenish yellow, or light blue ink.
♦ Remove all clips, staples, and pins
before loading documents in the
feeder (these will damage the
machine).
♦ Ink, glue, or correcting fluid on a
document must be dry before
scanning.
Transmittable Documents
♦ Documents which are taped, torn,
smaller than the minimum size,
carbon backed, easily smudged, or
have a slick, coated surface should be
photocopied, and the copy loaded in
the feeder.
♦ Documents that are curled or have a
wave-like pattern must be flattened.
Loading the Document
Up to 20 letter-size sheets (5 legal-size
sheets) can be placed in the feeder at
once. (If the sheets do not feed or
double feeds occur, reduce the number
of sheets.) The sheets will feed
automatically starting from the bottom
sheet.
♦ To send or copy more than the
maximum number of sheets, place
the additional sheets gently in the
feeder just before the last sheet is
scanned. Do not force the sheets in,
as this may cause double-feeding or
jamming.
♦ For large or thick sheets that must be
loaded one at a time, insert each
sheet into the feeder as the previous
sheet is being scanned. Insert gently
to avoid double-feeding.
1 Flip up the feeder cover (➊) and
adjust the document guides to the
width of your document (➋).
49
4. Sending
Faxes
4. Sending Faxes
Resolution and Contrast
2 Place the document face down with
the top edge going in first, and
insert it all the way into the feeder.
Make sure that the roller draws the
document in.
Resolution and Contrast
You can adjust the resolution and
contrast before sending a document.
♦ The default resolution setting is
STANDARD. The default contrast
setting is AUTO.
♦ Adjust the settings each time you
don't want to use the default settings.
• Display: [READY TO SEND] .
3 Adjust the resolution and/or contrast
settings (p. 50), and then dial the
receiving machine (p. 51).
Removing a document from the
feeder
1 Open the cover (➊) and remove the
document (➋).
Note: The resolution and contrast
settings are only effective for sending;
not for receiving.
Resolution settings
STANDARD Use STANDARD for
ordinary documents.
This provides the fastest
transmission.
FINE
• Caution: Attempting to remove a
document without opening the cover
may damage the feeder mechanism.
Use FINE for documents
containing small letters
or fine drawings.
SUPER FINE Use SUPER FINE for
documents containing
very small letters or very
fine drawings.
HALF TONE Use HALF TONE for
photographs and
illustrations. The original
will be reproduced in 64
shades of gray.
2 Close the cover, pressing down
firmly on both front corners.
50
Contrast settings
AUTO
Use AUTO for normal
documents.
DARK
Use DARK for faint
documents.
Sending a Fax: Normal Dialing
• The resolution/contrast cannot be
adjusted unless the document is
loaded.
2 Press
RESOLUTION/
RECEPTION MODE
one or more times
until the desired resolution and
contrast settings appear in the
display.
• The first time you move through the
list of resolution settings, the contrast
setting AUTO will appear next to
each resolution setting. The second
time you move through the list, the
contrast setting DARK will appear.
Note: In order to transmit in SUPER
FINE resolution, the receiving machine
must also have that resolution. If not,
your machine will automatically step
down to FINE.
If you prefer to use FINE for the
default resolution setting, change the
“FINE PRIORITY” setting (p. 69).
♦ Normal Dialing allows you to listen to
the line and make sure the other fax
machine is responding.
1 Load the document(s).
• If desired, press
RESOLUTION/
RECEPTION MODE
to set the
resolution and/or contrast.
2 Pick up the handset or press
SPEAKER
Listen for the dial tone.
3 Dial the fax number of the receiving
machine (press the number keys).
4 Wait for the connection. You will
4. Sending
Faxes
1 Load the document(s).
either hear a fax tone or the other
person will answer.
• If the other person answers, ask
them to press their Start key (if you
pressed
SPEAKER
, pick up the handset
to speak with them). The receiving
machine will issue a fax tone.
5 When you hear the fax tone, press
. Replace the handset.
• If the transmission is completed
Sending a Fax: Normal Dialing
With Normal Dialing, you pick up the
SPEAKER
handset (or press
) and dial by
pressing the number keys.
♦ If a person answers, you can talk with
them through the handset before
sending the fax.
successfully, the machine will beep
once.
• If an error occurs, the machine will
beep three times and print a
Transaction Report to inform you of
the problem (p. 75).
Note: If the transmission is
unsuccessful and the display shows
[DOCUMENT JAMMED], remove the
document as explained on page 88.
51
Sending a Fax: Auto Dialing
• If you prefer to have the machine
Sending a Fax: Auto Dialing
You can store your most frequently
dialed fax and phone numbers in Rapid
Keys and Speed Dial numbers.
dialed by simply pressing the Rapid
Key. A total of 36 Rapid Keys are
available. (Note: Attach the Rapid Key
labels as shown on page 7.)
to select “FAX”.
Display: [FAX # MODE]
4 Enter the fax or phone number with
the number keys (max. of 32 digits).
(Note: A space cannot be entered.)
• To clear a mistake, press
♦ A number stored in a Speed Dial
number is dialed by pressing
procedure, press
3 Press
♦ A number stored in a Rapid Key is
SPEED DIAL
suggest an available Rapid Key /
Speed Dial number at the end of the
• If a pause is required between any of
the 2-digit Speed Dial number, and
the digits to access a special service
then
or an outside line, press
. A total of 63 Speed Dial
numbers are available.
MENU
. The
pause appears as a hyphen (two
seconds per pause). Several pauses
can be entered in a row.
Note: E-mail addresses can also be
stored in Rapid Keys and Speed Dial
numbers (see page 44).
5 Press
Storing fax and phone numbers
6 Enter the name of the destination
Follow the steps below to store a fax or
phone number using the machine’s
operation panel.
♦ Fax/phone numbers can also be
stored using the machine’s Web page.
To access the Web page, see page
42.
1 Press
MENU
, then
2 To store a number in a Rapid Key,
press the desired Rapid Key.
To store a number in a Speed Dial
number, press
SPEED DIAL
and enter the
desired 2-digit number (01 to 63).
Display: [SELECT DEST. TYPE]
52
(max. 20 characters).
• For information on using the letter
keys, see page 8.
7 Press
• If you selected a Rapid Key or
Speed Dial number in Step 2, the
display will briefly show [STORED],
and then [NEW NUMBER]. Go to
Step 8.
• If you did not select a Rapid Key or
Speed Dial number in Step 2, the
display will show the next available
Rapid Key or Speed Dial number. If
that number is acceptable, press
and go to Step 8. If not, press
Sending a Fax: Auto Dialing
SPEED DIAL
and enter the desired 2-digit
Speed Dial number, and go to Step
8.
8 Return to Step 2 to store another
STOP
number, or press
To make changes to a previously stored
auto-dial number, or clear a number,
follow these steps:
MENU
, then
Dial number) of the number that you
want to edit or clear. (You can also
or
until the number
appears and press
.)
for “EDIT” or
6 Make the desired changes to the
name.
or
to move the cursor
to the letter or letters you wish to
change, and then press the
appropriate letter key. The new letter
will replace the old letter.
• If you do not wish to change the
name, go directly to Step 7.
STOP
another number, or press
to
exit.
Using an auto-dial number to
send a fax
1 Load the document(s).
Display: [1=EDIT, 2=CLEAR]
3 Press
8 Return to Step 2 to edit or clear
and enter the 2-digit Speed
press
5 Press
7 Press
2 Press the Rapid Key (or press
SPEED DIAL
number, go directly to Step 5.
• Press
to exit.
Editing and clearing auto-dial
numbers
1 Press
• If you do not wish to change the
4. Sending
Faxes
the desired Rapid Key, or press
for
“CLEAR”.
• If you selected “CLEAR”, go to Step
7.
If desired, press
RESOLUTION/
RECEPTION MODE
to set the
resolution and/or contrast.
2 Select the fax number using one of
the methods below:
4 If you selected “EDIT”, make the
desired changes to the number.
• Press
or
to move the cursor
to the digit or digits you wish to
change, and then enter the new digit.
The new digit will replace the old
digit.
53
Sending a Fax: Auto Dialing
• Rapid Key Dialing: If the number is
stored in a Rapid Key, press the
Rapid Key.
SPEED DIAL
stored in a Speed Dial number, press
and enter the Speed Dial
number with the number keys. Make
sure the correct destination appears
STOP
in the display (if not, press
then press
, and enter the 2-digit Speed Dial
number with the number keys.
• Speed Dialing: If the number is
SPEED DIAL
Speed Dialing: Lift the handset, press
), and
Search Dialing: Press
or
until
the name or number of the other party
appears, and lift the handset.
(You can also lift the handset first,
search for the number, and then press
.)
Sending a fax by Direct Keypad
Dialing
• Search Dialing: Press
or
until the name or number of the other
party appears in the display, and
Use this method to dial a full fax
number without using the handset .
press
1 Load the document(s).
• If desired, press
3 Dialing and transmission will take
place automatically.
• To cancel transmission, press
RESOLUTION/
RECEPTION MODE
to set the
resolution and/or contrast.
STOP
• If the transmission is completed
successfully, the machine will beep
once.
• If an error occurs, the machine will
beep three times and print a
Transaction Report to inform you of
the problem (p. 75).
Making a voice call with an auto-dial
number
Rapid Key Dialing: Lift the handset
and press the Rapid Key.
2 Enter the number of the receiving
machine with the number keys.
• If a pause is required between any of
the digits to access a special service
or an outside line, press
MENU
. The
pause will appear as a hyphen (two
seconds per pause). Several pauses
can be entered in a row.
3 Check the display. If the number
shown is correct, press
• If the number is not correct, press
STOP
to clear the incorrect digits, and
then re-enter the correct digit(s).
54
Sending a Fax: Auto Dialing
Redial
Automatic redialing
You can automatically redial the last
number dialed on the machine.
If you use auto dialing (including Direct
Keypad Dialing) to send a fax and the
line is busy, the machine will
automatically make three redial
attempts at intervals of five minutes.
• If desired, press
RESOLUTION/
RECEPTION MODE
to set the
resolution and/or contrast.
2 Press
once. Make sure the
display shows the number you wish
to dial.
3 If you are sending a fax, press
During this time, [RECALLING] will
appear in the display, followed by the
attempt number. You will not be able to
dial any other locations while the
message appears.
♦ To clear the message and stop
Dialing begins.
If you are making a phone call, lift
the handset. Dialing begins.
Note: If the transmission is
unsuccessful and [DOCUMENT
JAMMED] appears in the display,
remove the document as explained on
page 88.
STOP
automatic redialing, press
4. Sending
Faxes
1 Load the document(s).
Under certain conditions, automatic
redialing may stop before three
redialing attempts are made.
55
Batch Page Numbering
Batch Page Numbering
Sending a Fax From Memory
Use this feature to add a slash and the
total number of pages to each page
number on transmitted fax pages (for
example, "P. 1/5", "P.2/5", etc.). This
allows the recipient to check for missing
pages.
To increase transmission speed, you
can send a fax through the machine’s
memory. After transmission, the fax is
automatically cleared from memory.
1 Load the document(s).
2 Press
MENU
, then
until [PAGE
Display: [ENTER # (01 - 99)]
4 Enter the total number of pages
(“01” to “99”) with the numeric keys.
RESOLUTION/
RECEPTION MODE
, and dial using
one of the methods below. (Note that
an e-mail destination cannot be
selected.)
3 Press
5 If desired, press
To send a fax through memory, load the
document, press
COUNTER] appears.
Example: 5 pages
Note: If a power failure occurs while
sending a fax from memory, you must
repeat the operation.
to set the
resolution and/or contrast.
6 Dial the receiving machine and
♦ Press a Rapid Key.
♦ Press
SPEED DIAL
, enter a 2-digit Speed
Dial number, and press
♦ Enter the fax number with the number
keys and press
send the fax.
• To cancel a batch number entry,
remove the document from the
♦ Press
repeatedly to select an
auto-dial number and press
STOP
feeder or press
• If the number of pages actually
transmitted is not the same as the
batch number entered, an alarm will
sound and [PAGE COUNT ERROR]
will appear in the display. “PAGE E.”
will also appear in the NOTE column
of the Transaction Report if printed.
56
♦ Press
once to select the last
number dialed and press
If [MEMORY FULL] appears, see If the
memory becomes full on page 61.
Using AUTO Mode
5. Receiving Faxes
Using AUTO Mode
Answering with the machine’s
handset
To select AUTO mode, press
Important: If a document is loaded in
the machine’s feeder, remove it before
performing the steps below.
RESOLUTION/
RECEPTION MODE
(with no document in the
feeder) until [AUTO] appears in the
display.
1 When the machine rings, pick up
the handset.
♦ If you pick up the handset before the
machine answers, you can talk to the
other party and receive a fax as
explained in Using MANUAL Mode
below.
To change the number of rings on
which the machine answers calls,
change the “NUMBER OF RINGS”
setting (p. 69).
The machine automatically reduces
received faxes as needed to fit the
paper. If you prefer to have all faxes
printed at full size, change the
“RECEIVE RATIO” setting (pp. 69
and 72).
Using MANUAL Mode
To select MANUAL mode, press
RESOLUTION/
RECEPTION MODE
(with no document in the
feeder) until [MANUAL] appears in
the display.
In MANUAL mode, you must answer all
calls (even faxes) by picking up the
machine’s handset or an extension
phone connected to the same line.
2 If you hear a fax tone, wait until the
display shows [RECEIVING] and
then replace the handset.
• If [RECEIVING] does not appear (or
if you have set the Fax Signal
Receive setting to NO (pp. 69, 71)),
press
to begin reception.
3 If the other party first speaks with
you and then wants to send a fax,
press
after speaking. (Press
before the sender presses their
Start key.)
• When [RECEIVING] appears in the
display, hang up.
Answering a call on an
extension phone connected to
the same line
1 Answer the extension phone when
it rings.
2 If you hear a soft fax tone, wait until
you hear pronounced, high-pitched
fax tones, then hang up.
3 If the machine doesn't respond, or if
the other party first talks to you and
then wants to send a fax, set the
phone down (do not hang up), walk
57
5. Receiving
Faxes
In AUTO mode, the machine
automatically answers all calls on 4
rings and receives incoming faxes.
TEL/FAX Mode
♦ If your machine doesn't detect a fax
over to the machine, lift the
machine’s handset, and press
• The above step is necessary if you
have set the “FAX SIGNAL RX”
setting to NO (pp. 69 and 71).
Putting a call on hold
To put the other party on hold during a
phone call, press
INTERCOM/
HOLD
. When this is
done, they cannot hear you. You can
put the handset back in the cradle
without breaking the connection. When
you are ready to speak with the other
party again, pick up the handset. If you
did not put the handset back in the
cradle, press
INTERCOM/
HOLD
TEL/FAX Mode
To select TEL/FAX mode, press
(with no document in the
feeder) until [TEL/FAX] appears in
the display.
When the reception mode is set to TEL/
FAX, the machine automatically
answers all calls on 2 rings. After
answering, the machine monitors the
line for about five seconds to see if a
fax tone is being sent.
♦ If the machine detects a fax tone (this
means that the call is an
automatically dialed fax), it will
automatically receive the fax.
58
Note: Only the machine will make the
special ringing sound. An extension
phone will not ring after the machine
initially answers the call.
Reception to Memory
again to resume
conversation.
RESOLUTION/
RECEPTION MODE
tone (this means that the call is a
voice call or manually dialed fax), it
will make a special ringing sound for
15 seconds to alert you to pick up the
machine’s handset (to change the
number of seconds, see p. 69 and
“PSEUDO RING DURATION” on p.
70). If you don't answer within this
time, the machine will send a fax tone
to the other machine to allow the
calling party to send a fax manually.
Incoming faxes will be received to
memory when printing is not possible,
such as when the machine runs out of
paper, the print cartridge needs
replacement, or the paper jams.
When you have received a fax in
memory, [FAX RX IN MEMORY] will
appear in the display, alternating with a
message that indicates the problem.
When you resolve the problem, the
stored faxes will automatically print out.
♦ If you received faxes to memory
because the machine ran out of
paper, be sure to add paper that is
the same size as the paper
previously used, or the fax print-out
size will not match the size of the
printing paper.
6. Making Copies
The machine can be used as a
convenience copier. Follow the steps
below to make copies.
Sorting copies
The machine is initially set to not sort
copies. If you wish to have copies
sorted as shown below, change the
“SORT COPY” setting to YES (pp. 69
and 73).
B C
Not sorted (MULTI COPY)
Sorted (SORT COPY)
B C
Originals
B C
Example: Two copies
each of three originals
If [MEMORY FULL] appears...
If you place many originals in the
feeder, the memory may become full
before all pages can be scanned (the
display will show [MEMORY FULL]). If
this happens, only the pages that were
scanned will be copied and the
remaining pages will automatically feed
out. Repeat the copy procedure for the
remaining pages, including the page
that was being scanned when the
memory became full.
Note: It may not be possible to make a
copy of an original if a high resolution
setting is used and/or the original
contains so much detailed content that
the memory becomes full before
scanning finishes.
1 Load the document(s). (Maximum
of 20 letter sheets or 5 legal sheets.)
• If desired, press
RESOLUTION/
RECEPTION MODE
to set the
resolution and/or contrast.
2 Select the following copy settings as
• Enlarge/reduce: Press
6. Making
Copies
needed:
or
to select 100%, 125%, 135%, 200%,
70%, 88% or 94%.
Default setting: 100%.
• Number of copies per original:
Enter a number from 1 to 99.
Default setting: 1
Example: Press
for two copies
3 When you are ready to begin
COPY/HELP
copying, press
59
Broadcasting
7. Special Functions
5 Press
Broadcasting
You can send the same document to as
many as 20 fax or e-mail destinations in
just one operation.
♦ The destinations must be all fax or all
e-mail. It is not possible to mix fax
and e-mail destinations.
Keys and Speed Dial numbers can be
selected. (It is not possible to enter a
full fax number or e-mail address.)
1 Load the document(s).
• If desired, press
to set the
3 Press
• Press a Rapid Key.
and enter a 2-digit
Speed Dial number.
• Press
or
until the desired
destination appears in the display.
(only for an e-mail
60
destinations, press
destinations, transmission will
begin.
transmission, press
automatically printed out after
Broadcasting is completed. If any
destinations in the "Note" column of
the report are marked "Busy" or
have a communication error code,
you will need to send the document
to those destinations again.
the following methods:
destination).
7 When you have finished selecting
• For fax, a Transaction Report is
4 Select a destination using one of
• Press
when it
to select e-mail
options (see Steps 4 to 6 on page
46). When you are ready to begin
to broadcast to FAX
SPEED DIAL
to scroll through
and check your entered
destinations. To delete a
destinations, you can press
destinations, or
to broadcast
to E-MAIL destinations.
• Press
• You can press
• If you are broadcasting to e-mail
B'CAST
the other desired destinations
(maximum of 20).
• If you are broadcasting to fax
resolution and/or contrast.
2 Press
6 Repeat Steps 4 and 5 for each of
destination, press
appears.
♦ Only destinations stored in Rapid
RESOLUTION/
RECEPTION MODE
to enter the destination.
, or
Broadcasting
If the memory becomes full...
If the memory becomes full during
scanning, [MEMORY FULL] will
appear in the display.
♦ Press
to send the pages which
have been stored up to that point in
memory (the remaining pages will
automatically feed out). After
transmission, the memory will be
cleared and you can send the
remaining pages. You will also need
to send the page which was being
scanned when the memory filled
up.
♦ To cancel the entire transmission,
Storing destinations in Group
Keys
Follow the steps below to store a group
of destinations in a Group Key.
♦ Rapid Keys 33/G1 and 34/G2 can be
used as Group Keys. A key cannot be
simultaneously programmed as both
a Group Key and a Rapid Key.
♦ Up to 20 fax or e-mail destinations
• If desired, press
RESOLUTION/
RECEPTION MODE
to set the
2 Press the appropriate Group Key
).
• If the group is a fax group,
transmission will begin.
♦ Only Rapid Key and Speed Dial
numbers can be stored in a Group
Key. Full numbers cannot be stored.
1 Press
MENU
, then
MODE] appears.
, then
ENTRY] appears.
resolution and/or contrast.
34/G2
e-mail. It is not possible to mix fax and
e-mail destinations.
2 Press
1 Load the document(s).
or
3 Press
(Press
group.)
until [ENTRY
until [GROUP
(SET) to store a group.
(CLEAR) to clear a
• If [GROUP SPACE FULL] appears,
both keys have already been
programmed. Clear one of the keys
and then store a group.
61
7. Special
Functions
If the destinations to which you want to
broadcast have all been stored in one
Group Key (see Storing numbers in
Group Keys which follows), you can
perform the broadcast operation using
the following simplified procedure:
33/G1
to begin transmission, press
♦ The destinations must be all fax or all
Broadcasting using a Group
Key
can press
to
select e-mail options (see Steps 4 to
6 on page 46). When you are ready
can be stored in one Group Key.
STOP
press
• If the group is an e-mail group, you
Caller ID (Requires Service)
4 Press the Group Key that you want
33/G1
to use (
or
). (If you are
clearing a Group Key, press the
Group key that you want to clear
and go to Step 8.)
• If [ALREADY STORED] or [RAPID #
STORED] appears, the key has
already been programmed. Clear the
key or try the other Group Key.
5 Select a destination using one of the
following methods:
• Press a Rapid Key.
• Press
SPEED DIAL
and enter a 2-digit
2 Press
or
until the desired
destination appears in the display.
• Press
, or
(only for an e-mail
destination).
to enter the destination.
the other desired destinations
(maximum of 20).
• You can press
to scroll through
and check your entered destinations.
To delete a destination, press
when it appears.
8 When you have finished entering the
destinations, press
STOP
to exit.
MENU
, then
until [OPTION
, then
until [CALLER-
ID] appears.
3 Press
(YES) to turn on Caller
ID. (To turn off Caller ID, press
and go to Step 7.)
4 If the area code must not be
7 Repeat Steps 5 and 6 for each of
62
If you subscribe to a Caller ID service,
you can have the machine and cordless
handset show the name and number of
the caller when you receive a call.
SETTING] appears.
• Press
9 Press
(Requires Service)
Important: To use this function, you
must subscribe to a Caller ID service
from your phone company. The
machine may not be compatible with
some Caller ID services.
1 Press
Speed Dial number.
6 Press
Caller ID
34/G2
included when you dial a local
phone number (within your area
code), press
to select SET
and enter your area code in Step 5.
(This will remove the area code from
local numbers stored in the Caller
ID list, allowing you to automatically
dial those numbers from the list (see
Caller ID list on page 63).)
If you do not need to have the area
code removed from local numbers
in the Caller ID list, press
go to Step 7.
and
Caller ID (Requires Service)
5 Enter the 3 digits of your area code.
Caller ID list
6 Press
The machine keeps a log of the most
recent 30 calls and faxes you have
received (the Caller ID list). You can
view the list and automatically dial a
number from the list.
STOP
7 Press
to exit.
Note: Some caller ID services may not
provide the name of the caller. In this
case, only the phone number will
appear when you receive a call.
Display messages
♦ The list is only available if you have
Caller ID service and have turned on
the Caller ID function.
♦ After you have received 30 calls, each
new call will delete the oldest call.
NO
SERVICE
No caller information was
received. Make sure that
your service has been
activated.
CALLER-ID Noise on the telephone
line prevented reception of
ERROR
caller information.
OUT OF
AREA
PRIVATE
CALL
The call was made from an
area which does not have
Caller ID service, or the
service is not compatible
with your service.
Caller information was not
provided at the caller’s
request.
♦ The Caller ID list can also be printed.
See page 74.
1 Press
until []
appears.
2 Press
or
to scroll through
the list.
• To exit the list, press
STOP
3 To dial a number, display the
number and:
• Fax: Load the document and press
. Transmission will begin.
• Voice call: Pick up the handset.
Dialing will begin automatically.
Deleting calls from the list
7. Special
Functions
One of the following messages will
appear while the machine rings if caller
information is not available.
To delete a single call from the list,
display the call and press
To delete all calls from the list, hold
down for 3 seconds while viewing
any number in the list.
63
Blocking Unwanted Faxes
Blocking Unwanted Faxes
Duplex Scanning
The Anti Junk Fax function blocks
reception of faxes from a fax number
that you specify.
Duplex Scanning is convenient for
transmitting or copying two-sided
documents. When this function is
selected, you simply feed all pages of
the document through the machine
once, turn the stack of pages over, and
feed the stack through again. The
machine will automatically sort the
pages into the correct order (front of 1st
page, back of 1st page, front of 2nd
page, back of 2nd page, etc.).
♦ If you are using the Caller ID function,
the Anti Junk Fax function will block
voice calls as well as faxes from your
specified Anti Junk Number.
To use this function, enter the fax
number that you want to block. Only one
number can be entered.
♦ Note that any blank sides must be
1 Press
MENU
, then
MODE] appears.
2 Press
, then
until [ENTRY
until [ANTI
JUNK #] appears.
1 Load the documents. Make sure the
3 Press
(SET) to store an Anti
Junk number.
(To clear a previously stored
number, press
go to Step 5.)
included when scanning the pages (if
the number of pages is not equal
each time the machine scans the
stack, an error will result).
(CLEAR) and
4 Enter the number with the number
pages are placed front-side down,
with the first page on the bottom.
• If desired, press
RESOLUTION/
RECEPTION MODE
to set the
resolution and/or contrast.
2 Press
DUPLEX
and then
keys (max. 20 digits).
3 Perform all steps of the desired copy
5 Press
4 When all pages of the document
STOP
6 Press
to exit.
♦ When a fax is blocked (or when a
voice call is blocked if you are using
the Caller ID function), a transaction
report (page 75) will print to inform
you (unless “TRANSACTION LIST” on
page 70 is set to “NEVER PRINT”).
64
or transmission operation.
have been scanned, turn the stack
over (do not change the page order)
and load the stack again.
5 Press
Receiving Faxes to E-mail
You can have incoming faxes from
specified fax numbers (or all fax
numbers) automatically converted to email and forwarded to designated e-mail
recipients.
♦ This provides a convenient means of
forwarding received faxes to someone
who is out of the office.
♦ This function can also be used to
send copies of all received faxes to an
administrator for centralized
document storage.
Storing (or clearing) groups of
originating fax numbers and
forwarding e-mail addresses
To use the Receive Fax to E-mail
function, you must first store one or
more groups of originating fax numbers
and forwarding e-mail addresses.
♦ One originating fax number and one
forwarding e-mail address can be
stored in each group. When a fax is
received, the machine will check each
stored group, and if the originating
number of the received fax matches a
fax number in one of the groups, the
machine will forward the fax to the email address in that group.
♦ You can also omit entry of an
originating fax number in a group and
have faxes from all originating fax
numbers forwarded to the e-mail
address.
1 Press
MENU
, then
until
[RCV FAX TO E-MAIL] appears.
2 Press
, then
to show
[FORWARDING ADDRESS] /
[1=SET, 2=CLEAR]
3 Press
to select “SET”.
• To clear a previously stored group,
press
4 Enter a 2-digit number from “01” to
“10” (this number is used to identify
the group you will store).
• If you are clearing a group, enter the
2-digit number of the group you wish
to clear and go to Step 8.
5 Enter the originating fax number.
• If you wish to have faxes from all
originating fax numbers forwarded,
go directly to Step 6 without entering
a fax number.
6 Press
7 Enter the e-mail address to which
you wish to have the faxes
forwarded.
• For information on using the letter
keys, see page 8.
8 Press
9 Return to Step 4 to store (or clear)
STOP
another group, or press
to exit.
♦ Up to 10 groups can be stored.
65
7. Special
Functions
Receiving Faxes to E-mail
Receiving Faxes to E-mail
Activating (and deactivating)
Receive Fax to E-mail
After you have stored one or more
Receive Fax to E-mail groups, follow the
steps below to activate the Receive Fax
to E-mail function.
1 Press
Printing a report
The machine is initially set to print a fax
forwarding report only when a
fowarding error occurs. If you would like
the machine to print a report each time
it forwards a received fax, follow the
steps below.
MENU
, then
until
[RCV FAX TO E-MAIL] appears.
1 Press
MENU
, then
until
[RCV FAX TO E-MAIL] appears.
2 Press
2 Press
3 Press
to select “ON”.
• To turn off Receive Fax to E-mail,
press
3 Press
(PRINT ERROR ONLY)
to print a report only when an error
to exit.
STOP
4 Press
Printing forwarded faxes
The machine is initially set to not print
received faxes that are forwarded. If you
want the machine to print forwarded
faxes, follow the steps below.
1 Press
MENU
, then
until
[RCV FAX TO E-MAIL] appears.
2 Press
, then
until [PRINT
RECEIVED FAX] appears.
3 Press
to select YES (print
forwarded faxes) or
NO.
STOP
4 Press
66
to exit.
until [REPORT
occurs, or
(ALWAYS PRINT)
to print each time a fax is forwarded.
STOP
4 Press
, then
SETTING] appears.
to select
to exit.
Secure Receive
Activating Secure Receive
Secure Receive
To prevent others from viewing or taking
your received faxes, use the Secure
Receive function. When this function is
activated, received faxes are held in
memory without being printed. To print
the faxes, a 4-digit “secure code” must
be entered.
Setting a secure code
The secure code is used to print
received faxes. Follow the steps below
to set a secure code.
• The secure code can be any 4-digit
number.
SECURE
, then
until
3 Enter a 4-digit secure code.
4 Press
unless a secure code has been set.
1 Press
, then
SECURE
until
[ACTIVATE SECURE RCV.] appears.
2 Press
3 Press
to select “YES”.
STOP
4 Press
to exit.
Printing received faxes
[SECURE # SET] appears.
2 Press
• Secure Receive cannot be activated
• The machine will print the secure
code for your records.
• Take care not lose the print-out or
forget the code. In the event that you
forget the code and have kept no
record, contact Sharp’s Customer
Assistance Center at 1-877-7948675.
When the memory is holding one or
more received faxes, [RECEIVED
SECURE FAX] will appear in the
display. Follow the steps below to print
the faxes.
1 Press
until [SECURE DATA
PRINT] appears.
2 Press
SECURE
3 Enter the 4-digit secure code.
4 Press
• Printing will begin.
• If the wrong code is entered,
7. Special
Functions
1 Press
Follow the steps below to activate
Secure Receive.
[WRONG SECURE #] will appear.
Go back to Step 3.
67
Secure Receive
Deactivating Secure Receive
Clearing the secure code
If you need to deactivate Secure
Receive (faxes will be automatically
printed when received), follow the steps
below.
To clear the secure code, follow the
steps below.
1 Press
SECURE
, then
until
[ACTIVATE SECURE RCV.] appears.
2 Press
• Secure Receive must be deactivated
before you can clear the secure
code.
1 Press
SECURE
, then
until
[SECURE # CLEAR] appears.
3 Press
to select “NO”.
2 Press
4 Enter the 4-digit secure code.
3 Enter the 4-digit secure code.
5 Press
4 Press
• The display will briefly show [NO
SELECTED] and then the date and
time.
• If the wrong code is entered,
[WRONG SECURE #] will appear.
Go back to Step 4.
68
• The display will briefly show
[CLEARED] and then the date and
time.
• If the wrong code is entered,
[WRONG SECURE #] will appear.
Go back to Step 3.
8. Option Settings and Print Settings
The option settings and print settings
allow you to customize the operation of
the machine to better suit your needs.
The option settings are related to
general operation. The print settings are
related to printing.
The option settings and print settings
have been initially configured at the
factory. To change a setting, follow the
steps below to display the desired
setting, and then change the setting as
explained in the tables that follow.
2 Press
, then
repeatedly until
the desired setting appears.
• The option settings and print settings
are described in the tables below
and on the following pages.
3 Enter a selection for the setting by
pressing the number keys as
explained in the table.
4 After entering a selection, the
subsequent option/print setting will
appear in the display. To exit the
STOP
1 Press
MENU
, then
until [OPTION
SETTING] or [PRINT SET-UP]
appears.
settings, press
Option Settings
Make a selection for the displayed setting as explained below.
This is done in step 3 of the above procedure.
Setting
Description
FINE PRIORITY This is used to change the default resolution for faxing from
STANDARD to FINE. Press
(YES) to select FINE, or
(NO) to select STANDARD.
Initial setting: NO (STANDARD)
NUMBER OF
RINGS
This is used to set the number of rings on which the machine
answers calls when the reception mode is set to AUTO. Enter any
number from 2 to 5.
Initial setting: 4 rings.
69
8. Option/Print
Settings
Option Settings
Option Settings
TRANSACTION This sets the condition for printing transaction reports (see page
LIST
75). Press a number key as follows:
(ALWAYS PRINT): Print after every fax transmission,
reception and error.
(ERROR/MEMORY): Print only after an error or memory
operation.
(SEND ONLY): Print after every fax transmission.
(ERROR ONLY): Print only when an error occurs.
(NEVER PRINT): Never print.
Initial setting: ERROR ONLY
DIAL MODE
This sets the dial mode. Press
(TONE) if you are on a tone
dial line, or
(PULSE) if you are on a pulse dial line.
Initial setting: TONE
PSEUDO RING
DURATION
This sets the duration of the special ringing sound that alerts you
to voice calls and manually dialed faxes in TEL/FAX reception
mode. Press a number key as follows:
15 seconds
30 seconds
60 seconds
120 seconds
Initial setting: 15 seconds
70
FAX SIGNAL
RX
The machine will automatically begin reception if you hear a soft
fax tone after answering a call on the machine’s handset or an
extension phone. If you use a computer fax modem to send
documents on the same line, you must turn this function off in
order to prevent the machine from mistakenly attempting to
receive documents from the computer fax modem. Press
(YES) to turn on the the automatic reception function, or
(NO) to turn off the function. If you select NO, you must start
reception manually by pressing
on the machine each time
you hear a soft fax tone after answering a call.
Initial setting: YES
CALLER-ID
AUTO PRINT
OUT
If you subscribe to a Caller ID service from your phone company,
use this setting to have the ID of the caller appear in the display
each time you receive a call. For more information, see page 62.
Initial setting: NO
Press
(YES) to have the machine automatically print an
Activity Report once every 30 send/receive operations. (The
report can still be printed manually at any time.) Press
to turn off Auto Print Out.
Initial setting: NO
ECM MODE
(NO)
Press
(YES) to have any distortions in a transmission due to
noise on the telephone line automatically corrected before printout at the receiving end. This is only effective when the other
machine has ECM as well. Press
(NO) to turn off ECM
mode. (When there is considerable noise on the line, you may find
that ECM slows transmission. Turning off ECM mode may
increase transmission speed.)
Initial setting: YES
71
8. Option/Print
Settings
Option Settings
Print Settings
DIAL TONE
DETECTION
Press
(YES) to have the machine verify the presence of a
dial tone on the line before automatic dialing. Press
(NO) to
turn this function off.
Note: If you select YES and find that the machine is unable to dial,
change the setting to NO.
Initial setting: NO
KEY TONE
Press
(ON) to have the machine sound a beep each time a
key is pressed on the operation panel (this confirms that the key
has been correctly pressed). Press
beep sound.
Initial setting: ON
(OFF) to turn off the
Print Settings
Make a selection for the displayed setting as explained below.
This is done in step 3 of the procedure on page 69.
Setting
RECEIVE
RATIO
Description
Press
(AUTO) to have the machine automatically reduce the
size of received faxes to fit the size of the printing paper. This
ensures that the edges of a fax are not cut off. (Note: AUTO may
not operate if the received fax is too long, contains many fine
graphics or images, or is sent at high resolution. In this case, the
remainder of the fax will be printed on a second page.) Press
(100%) to have all faxes printed at full size (if a fax is too
long to fit on the paper, the remainder will be printed on a second
sheet; note that the cut-off point may occur in the middle of a line).
Initial setting: AUTO
72
PAPER SIZE
This sets the size to which the machine scales received faxes.
Press
(LETTER) if you loaded letter size paper, or
(LEGAL) if you loaded legal size paper.
Initial setting: LETTER
SORT COPY
This setting determines whether or not copies are collated (sorted
into sets) when multiple copies of each original page are made.
Press
(YES) to have copies automatically sorted, or
(NO) to have copies grouped by page.
Initial setting: NO
INK SAVE
MODE
To use less ink and speed up ink drying time when printing faxes
and copies, press
(ON) to turn on Ink Save Mode. If you
prefer a higher quality image, press
Save Mode.
Initial setting: OFF
QUALITY
MODE
(OFF) to turn off Ink
To have the machine print higher quality images by printing slowly
when the resolution is set to HALF TONE, press
(YES) to
turn on Quality Mode. If you prefer faster printing at the expense of
slightly reduced image quality when using HALF TONE, press
(NO) to turn off Quality Mode.
(Note: This setting does not affect the amount of ink used.)
Initial setting: YES
ALIGN
CARTRIDGE
This is used to align the print cartridge to improve print quality.
See page 77.
CLEAN
NOZZLES
This is used to clean the print cartridge nozzles if print quality is
not satisfactory after aligning the print cartridge. See page 77.
73
8. Option/Print
Settings
Print Settings
9. Printing Lists
You can print lists showing settings and
information entered in the machine.
1 Press
MENU
, then
until [LISTING
MODE] appears.
2 Press
3 Press
or
until the desired
list (see below) appears.
• ACTIVITY LIST: This report shows
information on your most recent
transmissions and receptions
(combined maximum of 30). The
headings are the same as in the
Transaction Report (see the next
section). The logged transactions are
erased after the report is printed. To
have the report print automatically
whenever the number of logged
transactions reaches 30, see page
69 and “AUTO PRINT OUT” on page
71.
• DESTINATION LIST: This shows
the fax and e-mail destinations that
have been stored in Rapid Key and
Speed Dial numbers (pp. 44 and 52).
• GROUP LIST: This shows the
destinations that are stored in the
Group Keys (p. 61).
• SETUP LIST: This shows your
currently entered sender’s name,
sender’s number, and anti-junk fax
number, your current selections for
the option settings, print setup, and
receive faxes to e-mail, and a
sample of the header printed at the
top of every fax page you transmit
(HEADER PRINT).
• CALLER-ID LIST: This shows
information on your 30 most recently
received calls and faxes (p. 63).
(This list is only available if you are
using the Caller ID function.)
• RECEIVE FAX TO E-MAIL LIST:
This shows the Receive Fax to Email settings that have been stored
(page 65).
• NETWORK SETTING LIST: This
shows the machine’s current IP
address and other network/Internet
settings (page 48).
4 Press
74
to print the list.
Transaction Report
This report is printed out automatically
after a fax is sent or received to allow
you to check the result. The machine is
initially set to print out the report only
when an error occurs.
♦ The Transaction Report cannot be
printed manually. To change the
condition for automatically printing out
Transaction Reports, see page 69
and “TRANSACTION LIST” on page
70.
Headings in the Transaction Report
SENDER/ The name or fax number of
RECEIVER the other machine.
START
Starting time.
TX/RX
TIME
Total time taken for
transmission/reception.
PAGES
Number of pages.
NOTE
One of the following notes
will appear under NOTE to
indicate whether the fax was
successful, and if not, why it
failed.
OK - Transmission/reception
was successful.
P.FAIL - A power failure
prevented the transaction.
JAM - The printing paper or
document jammed.
BUSY - The fax was not sent
because the line was busy.
COM.E-X - (Where “X” is a
number.) A communication
error occurred. See page 80.
CANCEL - The fax was
canceled because the STOP
key was pressed, no
document was in the feeder,
or the other machine
requested a function that
your machine does not have.
75
9. Printing
Lists
Transaction Report
Cleaning the Machine
10. Maintenance
Cleaning the Machine
Cleaning the scanning glass
and rollers
Any dirt on the scanning glass and
rollers will degrade the quality of
transmitted documents and copies.
Clean these frequently as explained
below.
♦ If the document does not feed or
double-feeds occur, use a cloth
moistened with water to wipe the
rollers.
1 Open the
• Do not wipe off the grease on the
ends of the white roller.
• Make sure that all dirt and stains
(such as correcting fluid) are
removed. Dirt and stains will cause
vertical lines on transmitted images
and copies.
• If the scanning glass is difficult to
clean, try moistening the cloth with
isopropyl alcohol or denatured
alcohol. Take care that no alcohol
gets on the rollers.
• Do not press down on the two front
rollers.
• Use a cloth moistened with alcohol
cover.
2 Rotate the lever so that it points
straight up (➊) and pull it up (➋).
to wipe off any splattered ink on the
inside of the compartment or the
underside of the cover. (Do not wipe
the rollers or rubber sheet with the
alcohol-moistened cloth.)
4 Replace the white roller, inserting
the left end first. Push the lever
down and rotate it back down.
3 Pull the white roller out to the right.
Wipe the scanning glass, rollers,
and rubber sheet with a clean cloth
or swab.
White roller
Scanning
glass
Rollers
76
Rubber sheet
Improving Print Quality
firmly to make sure it clicks into
place.
4 In the page that the machine prints,
locate the line that is closest to a
completely straight line.
In this example, “15” is
closest to a straight line.
Cleaning the housing
Wipe the external parts and surface of
the machine with a dry cloth.
Caution: Do not use benzene or
thinner. These solvents may damage or
discolor the machine.
10. Maintenance
5 Close the cover, pressing down
5 Enter the number of the straightest
line with the number keys.
• To clear a mistake, press
6 Press
[CLEAN NOZZLES]
STOP
Improving Print Quality
7 Press
to exit.
Aligning the print cartridge
If print quality is not satisfactory, first try
aligning the print cartridge.
Cleaning the print cartridge
nozzles
Note: Make sure that paper is loaded
before beginning this procedure.
If print quality is still not satisfactory
after aligning the print cartridge, clean
the print cartridge nozzles.
1 Press
MENU
, then
SET-UP] appears.
until [PRINT
2 Press
, then
until [ALIGN
CARTRIDGE] appears.
3 Press
to print an alignment
page. (To enter an alignment value
without printing a page, press
.)
1 Press
MENU
, then
SET-UP] appears.
until [PRINT
2 Press
, then
until [CLEAN
NOZZLES] appears.
3 Press
• The machine prints a test pattern
similar to the one shown in the
following step.
77
Improving Print Quality
4 Compare the diagonal lines above
the printed bars to the diagonal
lines below the printed bars.
• Look for breaks in the diagonal lines
above the bars. Breaks indicate
clogged nozzles.
Breaks in the diagonal lines at the top
of the page indicate clogged nozzles.
Wiping the print nozzles and
contacts
If you have cleaned the print nozzles as
explained in the previous section at
least three times and print quality is still
not satisfactory, try wiping the print
nozzles and contacts.
1 Open the cover and remove the
print cartridge (see the procedure
beginning on page 13).
• CAUTION! DO NOT touch the gold
contact area of the cartridge or the
contact area of the cartridge holder
with your fingers.
2 Place two or three sheets of paper
Unbroken lines at the bottom of the
page indicate the nozzles were cleaned.
5 If the bottom diagonal lines still
have breaks, repeat Steps 1
through 4 to clean the nozzles
again. Repeat several more times if
necessary.
on a table or other flat surface.
Moisten a clean, lint-free cloth with
warm water and place the cloth on
the paper.
3 Gently press the nozzles against
the cloth for about three seconds,
and then move the cartridge slowly
in the direction shown to wipe the
nozzles.
• If the print quality is still not
satisfactory after cleaning the
nozzles several times, continue with
Step 6.
6 Open the cover and remove and
then reinstall the print cartridge
(see the procedure beginning on
page 13).
7 Repeat the nozzle cleaning
procedure. If the lines are still
broken, wipe the nozzles as
explained in the following section.
78
4 Using another clean section of the
cloth, repeat the above step.
Improving Print Quality
5 Moisten another clean cloth with
Cleaning the cartridge holder
A dirty print cartridge holder may cause
smudges on your printed pages. To
clean the print cartridge holder, open
the cover and remove the print cartridge
(see the procedure beginning on page
13). Wipe the part indicated below with
a damp cloth.
10. Maintenance
warm water. Gently hold the cloth
against the contacts for about 3
seconds, and then wipe in the
direction shown.
6 Using another clean section of the
cloth, repeat the above step.
7 Allow the nozzles and contacts to
dry completely.
8 Reinstall the print cartridge and
repeat the nozzle cleaning
procedure as explained in the
previous section.
• If print quality is still not satisfactory
after the nozzles are cleaned,
replace the print cartridge (see page
13).
About the lithium battery:
The machine uses a lithium battery to
retain settings and information
programmed in the machine when
the power is turned off. Battery power
is consumed primarily when the
power is off. With the power kept
continuously off, the life of the battery
is about 5 years. If the battery dies,
have your dealer or retailer replace it.
Do not try to replace it yourself.
79
Problems and Solutions
11. Troubleshooting
Problems and Solutions
If you have any problems with the machine, first refer to the following
troubleshooting guide. If you cannot solve the problem, call Sharp's Customer
Assistance Center at 1-877-794-8675.
♦ For network connection problems (Fax to E-mail), see page 41.
Line error
Problem
LINE ERROR appears in
the display.
Solution
A line error occurs when your machine cannot
communicate correctly with another fax machine. The
error is usually due to a problem on the phone line.
Try faxing again. If unsuccessful, check the following:
• Check the connection. The cord from the TEL. LINE
jack to the wall jack should be no longer than six feet.
• Make sure there are no modem devices sharing the
same telephone line.
• Check with the other party to make sure their fax
machine is functioning properly.
• Have your telephone line checked for line noise.
• Try connecting the machine to a different phone line.
• If the error persists, the machine may need service.
Dialing and transmission problems
Problem
No dial tone when you
pick up the handset or
press the SPEAKER key.
Solution
• Make sure the handset cord is connected to the
correct jack. See Connect the handset on page 11.
• Make sure that the telephone line is properly
connected to both the TEL. LINE jack and the wall
jack (see page 15).
• Make sure that the telephone line is good.
80
Problems and Solutions
Dialing is not possible.
• Make sure the power cord is properly plugged into a
power outlet.
• Make sure that the telephone line is properly
connected to both the TEL. LINE jack and the wall
jack (see page 15).
• Make sure that the machine is set to the correct
dialing mode for your telephone line. See the
procedure on page 69 and “DIAL MODE” on page 70.
The power is on, but no
transmission takes place.
• Make sure that the receiving machine has paper.
• If the receiving machine is in manual mode with no
attendant, reception will not be possible.
• Pick up the handset and check for a dial tone. Dial the
receiving machine manually and make sure that it is
responding (you should hear a fax tone).
Nothing is printed at the
receiving end.
• Make sure that the document for transmission is
placed face down in the feeder.
A distorted image is
received at the other end.
• Noise on the telephone line may cause distortion. Try
sending the document again.
• Make a copy of the document on your machine. If the
copy is also distorted, your machine may need
service.
Reception and copying problems
Problem
The machine doesn't
receive documents
automatically.
Solution
• Make sure that the reception mode is set to AUTO.
81
11. Troubleshooting
• Check the display for error messages.
Problems and Solutions
The printing paper comes
out blank when you try to
receive a document.
• Make sure that the document is loaded properly in the
feeder of the transmitting machine. Make a copy or
print a report to confirm the printing ability of your
machine.
Print quality is poor.
• The print cartridge may need alignment or cleaning.
See page 77.
The received document is
faint.
• Ask the other party to send higher contrast
documents.
• The print cartridge may need replacement. Make a
copy or print a report to check your machine’s printing
ability.
Received images are
distorted.
• Noise on the telephone line may cause distortion.
Have the other party try sending the document again.
• Make a copy or print a report on your machine. If the
copy or report is also distorted, your machine may
need service.
The quality of copies is
poor and/or dark vertical
lines appear.
• Any dirt or material on the scanning glass will cause
spots to appear on copies and transmitted faxes.
Clean the scanning glass as explained on page 76.
General problems
Problem
Nothing appears in the
display.
Solution
• Make sure the power cord is properly plugged into a
power outlet.
• Connect another electrical appliance to the outlet to
see if it has power.
The machine does not
respond when you press
any of its keys.
• If a beep sound is not made when you press the keys,
unplug the power cord and then plug it in again
several seconds later.
Automatic document
feeding does not work for
transmission or copying.
• Check the size and weight of the document (see
Transmittable Documents on page 49).
82
Problems and Solutions
Cordless handset problems
Solution
The cordless handset
does not operate and
nothing appears in the
display.
• Make sure the batteries are correctly inserted in the
cordless handset (see page 18).
Calls cannot be made or
received on the cordless
handset.
• Make sure the machine is plugged into a power outlet
and has power.
• The batteries may be low. Place the cordless handset
in the charger and let it charge.
• Make sure the telephone line is properly connected to
both the TEL. LINE jack on the machine and the wall
jack (see page 15). (If the telephone line is connected
correctly, you should hear a dial tone when you pick
up the machine handset.)
• The batteries may be low. Place the cordless handset
in the charger and let it charge.
• Calls cannot be made or received while the machine
is being used. Wait until the machine is no longer
being used.
• Calls cannot be made or received during a power
failure.
• You may be outside of the talking range. Move closer
to the machine.
You hear noise or
interference during a call.
• Other electrical appliances may cause interference.
Move away from any electrical appliances.
• Move closer to the machine. Note that large metal
objects, metal structures, and thick walls between the
machine and cordless handset will reduce the talking
range. If needed, try moving the machine to a different
location.
83
11. Troubleshooting
Problem
Problems and Solutions
The batteries do not
charge.
• Make sure the cordless handset is placed in the
charger with the dial pad facing forward.
• Make sure the charger is connected correctly to the
power outlet (see page 18).
• Wipe the charger contacts with a cotton swab.
• Make sure the batteries are correctly inserted in the
cordless handset (see page 18).
• The batteries may need replacement (see page 19).
You hear beeps during a
call.
84
• You will hear beeps during a call and the battery
indicator will blink in the display if the batteries are
low. Place the cordless handset in the charger and let
it recharge. If you hear beeps during a call and need
to continue the call, transfer the call to the machine
(see page 21).
Messages and Signals
Messages and Signals
Display messages
Note: If you have turned on the Caller ID function, see page 63 for display
messages related to Caller ID.
Check the printing paper. If the tray is empty, add paper
and then press
. If there is paper in the tray, make
sure it is inserted correctly (take out the stack, align the
edges evenly, and then reinsert it in the tray) and then
press
CHANGE CARTRIDGE
This message appears after you install or replace the
print cartridge (see page 14).
CHECK CARTRIDGE
The print cartridge is missing and must be installed, or
is not installed correctly.
CONNECTION ERROR
A Fax to E-mail transmission was not successful
because of a communication problem on your local
network. This is usually due to a problem with the cable
connections. Make sure that the cable ends are
securely inserted in the LAN ports. Make sure that the
correct cable is being used and that the cable is good.
Make sure that your router or hub is powered on.
CHECK E-MAIL SETTING Fax to E-mail transmission is not possible because the
SMTP server or the sender address has not been
specified in the e-mail settings (see page 42).
DOCUMENT JAMMED
The original document is jammed. See the following
section, Clearing Paper Jams. Document jams will occur
if you load more than 20 pages at once or load
documents that are too thick (see page 49). The
document may also jam if the receiving machine doesn’t
respond properly when you attempt to send a fax.
FAX RX IN MEMORY
A fax has been received in memory because the print
cartridge needs replacement, you have run out of
printing paper, or the paper is jammed. The fax will print
out automatically when the problem is fixed.
85
11. Troubleshooting
ADD PAPER & /
PRESS START KEY
(alternating messages)
Messages and Signals
INK NEAR EMPTY
The cartridge is nearly empty (approximately one eighth
of the ink remains).
LINE ERROR
Transmission or reception was not successful. Press
STOP
to clear the message and then try again. If the error
persists, see Line error on page 80.
LOW INK
The cartridge is low on ink (approximately one quarter
of the ink remains).
MEMORY FULL
If faxes have been received to memory because printing
is not possible, resolve the problem so that printing can
continue (see Reception to Memory on page 58).
If faxes are being held in memory because the Secure
Receive function has been activated, print the faxes as
explained on page 67.
If you are attempting to broadcast or transmit from
memory, see If the memory becomes full on page 61.
If you are copying, see If MEMORY FULL appears on
page 59.
OUT OF INK
The cartridge is out of ink and must be replaced. Faxes
will be received to memory.
PAPER JAMMED
The printing paper is jammed. See page 88.
PRINTER ERROR
A printer error has occurred. Open the cover, make sure
the print cartridge is installed correctly, and then close
the cover.
PRINTER ERROR/
CHECK PAPER
A paper jam may have occurred. Follow the procedure
on page 88 to clear the jam.
RECALLING
This appears if you attempt to send a fax by auto dialing
and the line is busy or the receiving fax machine does
not answer. Your machine will automatically reattempt
the call. (See Automatic redialing on page 55.)
RECEIVED SECURE FAX A received fax is being held in memory because the
Secure Receive function has been activated. Enter your
secure code to print the fax (see page 67).
86
Messages and Signals
SERVER ERROR
A Fax to E-mail transmission was not successful
because the machine could not connect to your mail
server or there was no response from the mail server.
Make sure the SMTP server setting is correct (p. 43). If
you have configured “POP before SMTP” settings in the
Web pages, make sure these settings are correct. If
[CABLE DISCONNECTED] appears on the bottom line,
see “CONNECTION ERROR” on page 85.
SERVER NOT FOUND/
CABLE DISCONNECTED
See “CONNECTION ERROR” on page 85.
A Fax to E-mail transmission was not successful
because the machine was unable to automatically obtain
an IP address. Restart your router or other device that
acts as your DHCP server.
SERVER NOT FOUND/
SMTP
A Fax to E-mail transmission was not successful
because an incorrect host name is entered for your
SMTP server. Check the SMTP server setting (p. 43).
11. Troubleshooting
SERVER NOT FOUND/
DHCP
Audible signals
Continuous tone
3 seconds
Indicates the end of transmission,
reception, or copying.
Intermittent tone
(3 beeps)
5 seconds
(1 second on, 1
second off)
Indicates incomplete transmission,
reception, or copying.
87
Clearing Paper Jams
2 Replace the white roller, inserting
Clearing Paper Jams
Clearing a jammed document
If the original document doesn’t feed
properly during transmission or copying,
or [DOCUMENT JAMMED] appears in
the display, first try pressing
the left end first. Push the lever
down and rotate it back down
(➊).Close the cover, pressing firmly
on both front corners (➋).
. If the
document doesn't feed out, remove it as
explained below.
Important: Do not try to remove a
jammed document without releasing it
as explained below. This may damage
the feeder mechanism.
1 Open the cover (➊). Rotate the lever
so that points straight up (➋), and
pull it up (➌). Pull the roller out to the
right, and remove the document (➍).
Clearing jammed printing paper
1 Open the cover (➊). Pull the
jammed paper forward or backward
out of the machine as appropriate
(➋), taking care not to tear it.
2 Close the cover, pressing down
firmly on both front corners.
88
Ordering Parts
Ordering Parts
To order parts, contact the parts distribution center located nearest you.
When ordering a part, use the part order number shown below.
Operation manual
Setup Guide
Handset cord
Telephone line cord
Handset
Paper tray
Document exit tray
Received document tray
Rapid Key labels
TINSE4529XHTZ
TCADH3899XHZZ
QCNWG202DXHFW
QCNWG370BXHZZ
DUNTK245DXHPW
LPLTP3435XHSA
LPLTP3434XHSA
LPLTP3442XHSA
TLABH415KXHSC
Part distribution centers
Tritronics, Inc.
1306 Continental Drive
Abingdon, MD 21009
Tel: 1-800-638-3328
Fax: 1-800-888-FAXD
Tritronics, Inc.
1015 NW 52nd Street
Ft. Lauderdale, FL 33309
Tel:1-800-365-8030
Fax: 1-800-999-FAXD
Fox International, Ltd.
23600 Aurora Road
Bedford Heights, OH 44146
Tel: 1-800-321-6993
Fax: 1-800-445-7991
Andrews Electronics
25158 Avenue Stanford
Santa Clarita, CA 91355
Tel: 1-800-274-4666
Fax: 1-805-295-5126
Sharp Accessories and
Supply Center
2130 Townline Road
Peoria, IL 61615
Tel: 1-800-642-2122
89
FCC Regulatory Information
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
ACTA. On the rear of this equipment is a label that contains, among other information, a product
identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the
telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See installation instructions for
details. This equipment connects to the telephone network through a standard USOC RJ-11C
network interface jack.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an
incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as determined by the total
RENs, contact the local telephone company. For products approved after July 23, 2001, the REN
for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The
digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For
earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice isn't
practical, the telephone company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures
that could affect the operation of the equipment. If this happens the telephone company will
provide advance notice in order for you to make necessary modifications to maintain
uninterrupted service.
If trouble is experienced with this equipment, or for repair or warranty information, please contact
Sharp’s Customer Assistance Center. The number is 1-877-794-8675. If the equipment is
causing harm to the telephone network, the telephone company may request that you disconnect
the equipment until the problem is resolved.
This equipment may not be used on coin service provided by the telephone company.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this equipment ID does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualified installer.
This equipment is hearing-aid compatible.
When programming and/or making test calls to emergency numbers:
♦ Remain on the line and briefly explain to the dispatcher the reason for the call.
♦ Perform such activities in the off-peak hours, such as early morning or late evening.
90
S H A R P
Date Revised:
Date Issued: Apr. 25. 2006
MATERIAL SAFETY DATA SHEET (1/3)
MSDS No. B-1029
Section 1. Product and Company Identification
Product Name : Ink cartridge of UX-C80B
Supplier Identification : Sharp Corporation
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
Local suppliers are listed below. Please contact the nearest supplier for additional information.
(Area)
(Country)
(Name and Telephone Number)
North
America
U.S.A.
Sharp Electronics Corporation
Telephone number for information: 1-800-237-4277
Emergency telephone number :
1-800-255-3924
Canada
Sharp Electronics of Canada Ltd.
Telephone number for information : 905-890-2100
Emergency telephone number :
1-800-255-3924
Section 2. Ingredients
Ingredients
Carbon Black
Acrylic Terpolymer
Water Soluble Organic Solvents
Cas No.
Proportion
1333-86-4
Trade
Secret(#)
Trade
Secret(#)
1-5
Hydroxylated Alkane
Trade
Secret(#)
NJTSRN 80100451-5004
7732-18-5
Water
# : Supplier's confidential information
OSHA PEL
ACGIH TLV
3.5 mg/m3 TWA 3.5 mg/m3 TWA
0.1-2
None
None
10-20
None
None
1-10
None
None
60-78
None
None
Section 3. Hazardous Identification
The following information from our supplier is based on testing of the product as a whole and/or characteristics
of components.
Hazard Information : Primary Routes of Exposure: Ingestion, skin contact.
Inhalation :
If ink mist is inhaled, respiratory tract irritation may occur. Exposure not probable with
intended use.
No adverse chronic effects known at intended level of use.
Skin Contact :
Not an irritant. Exposure not probable with intended use. Not a dermal sensitizer.
Eye Contact :
Not an irritant. Exposure not probable with intended use.
Ingestion :
Low acute oral toxicity. Exposure not probable with intended use.
Section 4. First-Aid Measures
Inhalation: If symptoms, such as shortness of breath or persistent coughing are experienced, remove source
of contamination and move individual to fresh air. If symptoms persist, seek medical attention.
Skin Contact: Wash with soap and water. Should irritation occur, seek medical attention.
Eye Contact: Flush immediately with plenty of water. Remove contact lenses and continue flushing for at
least 15 minutes.
If irritation develops and persists, seek medical attention.
Ingestion: Immediately wash mouth out with plenty of water. Do not induce vomiting. Slowly dilute with 1-2 glasses
of water or milk and seek medical attention. Never give anything by mouth to an unconscious person.
Aggravated Conditions : None known
Notes to Physician :
No specific antidote.
Section 5. Fire-Fighting Measures
Flash Point/Range (°C) :
Autoignition Temperature (°C) :
Flammable Limits in Air UEL :
Flammable Limits in Air LEL :
Extinguishing Media :
Hazardous Combustion Products :
Special Exposure Hazards :
Special Protective Equipment :
NFPA Rating :
HMIS Classification :
Not applicable
Not determined
Not determined
Not determined
Carbon dioxide, water spray or fog, dry chemical or foam
Carbon monoxide, carbon dioxide, unidentified organics
None known
NIOSH approved self contained breathing apparatus may be required
if a large number of cartridges are involved.
Health: 1 Flammability: 0 Reactivity: 0
Health: 1 Flammability: 0 Reactivity: 0
91
S H A R P
Date Revised:
Date Issued: :Apr. 25. 2006
MATERIAL SAFETY DATA SHEET (2/3)
MSDS No. B-1029
Section 6. Accidental Release Measures
Personal Precautionary Measures :
Environmental Precautionary :
Procedure for Cleaning/ Absorption :
None required for intended use in printer.
Unless specifically permitted for disposal, keep waste out of sewers,
watersheds, and waterways.
Absorb small spills with cloth or paper towels or other suitable
material. Place in container for disposal. For large spills, dike
around spill with absorbent material. Wash spill site with soap and
water after material pickup is complete. Disposal is subject to
federal, state, local, or provincial regulations.
Section 7. Handling and Storage
Handling : To avoid damage to cartridge and accidental contact with ink
KEEP OUT OF REACH OF CHILDREN.
Storage : Store in a cool, dry place.
Section 8. Exposure Control/Personal Protection
Engineering Controls :
Respiratory Protection :
Gloves :
Skin Protection :
Eyes :
None required.
None required for intended use in printer.
None required for intended use in printer.
None required for intended use in printer.
None required for intended use in printer.
Section 9. Physical and Chemical Properties
Physical State:
Color :
Odor:
Solubility in Water:
Cartridge contains liquid ink
Black
Faint
Fully Miscible
Pressurized:
No
pH:
7.0-8.5
Specific Gravity: Approx. 1.0
Specific Gravity: Approx. 1.0
Section 10. Stability and Reactivity
Chemical Stability :
Hazardous Polymerization :
Conditions to Avoid :
Materials to Avoid :
Hazardous Decomposition Products :
Additional Guidelines :
Stable
Will not occur
None known
None known
Carbon monoxide, carbon dioxide, unidentified organics
None
Section 11. Toxicological Information
Primary Routes of Exposure : Ingestion, skin contact.
Ingestion : Low acute oral toxicity. Exposure not probable with intended use. Based on component
characteristics, gastrointestinal, liver, kidney, and CNS effects are possible if large quantities of
ink are ingested.
Acute Toxicity Oral Rat LD50(mg/kg) : >2000
Inhalation : Low acute inhalation toxicity. Pure carbon black, a minor component of this product, has been
listed by IARC as a group 2B (possible carcinogen). This classification is based on rat "lung
particulate overload" studies performed with airborne particulate carbon black. Toner is not
listed by IARC, NTP, or OSHA.
Aggravated Conditions :
None known
Carcinogenicity Comment : Neither this product nor any of its components present above 0.1% are listed
by IARC, NTP, or OSHA as known carcinogens.
Section 12. Ecological Information
Mobility :
Persistence :
Bioaccumulative :
Other Information :
92
Not determined
Not determined
Not determined
None
S H A R P
Date Revised:
Date Issued: :Apr. 25. 2006
MATERIAL SAFETY DATA SHEET (3/3)
MSDS No. B-1029
Section 13. Disposal Consideration
Waste Disposal:
This product is not a listed hazardous waste in accordance with Federal Regulation 40 CFR Part 261. If
discarded in its purchased form, this product would not be a hazardous waste either by listing or by
characteristic. However, under RCRA, it is the responsibility of the product user to determine at the time of
disposal whether a material has been contaminated and should be classified as a hazardous waste. Disposal
is subject to local, state and federal regulations.
Section 14. Transport Information
DOT Status :
Not classified as a hazardous material or substance under US DOT.
DOT Shipping Name : Not applicable
DOT Reportable Quantity : Not applicable
Hazard Class :
Not applicable
DOT Packing Group :
Not applicable
Section 15. Regulatory Information
TSCA (USA) All ingredients are listed on the Toxic Substances Control Act (TSCA) inventory, have been
registered, or are exempt.
None of the ingredients in this product has a final reportable quantity (RQ) under
SARA / EPCRA (USA) :
Emergency Planning and Community Right-to Know Act (EPCRA)- Section 302
: Extremely Hazardous Substances (EHS) or notification requirements for EHS
under Section 304.
California Proposition 65 : This product contains no known materials at levels which the State of California
has found to cause cancer, birth defects or other reproductive harm - California
Proposition 65.
DSL (Canada) :
All ingredients are listed on the Canadian Domestic Substances List (DSL), have been
registered on the Non-Domestic Substances List (NDSL), or are exempt.
EINECS (Europe) : All ingredients are listed on the European Inventory of Existing Commercial Substances
(EINECS) list, have been registered on the European List of New Chemical Substances
(ELINCS), or are exempt.
ENCS (Japan) :
All ingredients are listed on the Japanese Existing and New Chemical Substances
(ENCS) list,have been registered, or are exempt.
AICS (Australia) : All ingredients are listed in Australian Inventory of Commercial Substances (AICS), or
are registered in Australia.
ECL (Korea) :
All ingredients are listed on the Korean Existing Chemicals List (ECL), have been
registered, or are exempt.
WHMIS Hazard Class (Canada) : Not a WHMIS controlled product.
Section 16. Other Information
Reference :
IARC(1996): IARC monographs on the Evaluation of the Carcinogenic Risk of Chemicals to
Humans, Vol. 65, Printing Process and Printing Inks, Carbon Black and Some Nitro Compounds,
Lyon, pp.149-261
H.Muhle, B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie,
P.Morrow, U.Mohr,
S.Takenaka, and R.Mermelstein(1991) Pulmonary Response to Toner upon Chronic Inhalation
Exposure in Rats.
Fundamental and Applied Toxicology 17, pp.280-299.
Restrictions :
This information relates only to the specific material designated as supplied by the manufacturer.
This information is supplied to us by the manufacturer and Sharp offers no warranties as to its
accuracy and accepts no responsibilities for any typographical errors which may appear on these
sheets. The information on this data sheet represents best opinion as to the proper use in handling
of this product under normal conditions. However, all materials may present unknown hazards and
should be used with caution. Although certain hazards are described herein, we do not guarantee
that these are the only hazards which exist. It is the responsibility of the user to determine the
suitability of this product for each particular use.
Revision Information :
2006/Apr./25 Not applicable in this time due to new issue.
93
Quick Reference Guide
Fax / Fax to E-mail Transmission
Receiving Faxes
Place your document (up to 20 pages)
face down in the document feeder.
Press
RESOLUTION/
RECEPTION MODE
until the desired
reception mode appears in the display.
AUTO mode: The machine
automatically answers and receives
faxes.
Sending a Fax by Normal Dialing
1 Lift the handset or press
begin fax reception, press
SPEAKER
2 Dial the fax number.
3 Wait for the reception tone (if a
person answers, ask them to press
their Start key).
4 Press
MANUAL mode: Answer all calls (even
faxes) by picking up the handset. To
TEL/FAX mode: The machine
automatically answers and receives
faxes. Voice calls are signalled by a
special ringing sound.
Storing Destinations
1 Press
Using a Rapid Key (fax/e-mail)
MENU
, then
2 Press an unused Rapid Key, or
SPEED DIAL
Press the Rapid Key for the destination.
press
Using a Speed Dial number
(fax/e-mail)
2-digit Speed Dial number (01 to
63). (For an e-mail destination, you
can also press the A, B or C key
and go to Step 4.)
1 Press
SPEED DIAL
2 Enter the appropriate 2-digit Speed
Dial number and press
Searching for a destination
(fax/e-mail)
1 Press
or
until the desired
destination appears.
3 Press
and enter an unused
for fax or
for e-
mail.
4 Enter the fax number or the e-mail
address.
5 Press
6 Enter a name with the letter keys.
STOP
2 Press
94
7 Press
and then
Receiving a fax using the cordless
handset
Using the Cordless Phone
Making a call
1 Pick up the cordless handset and
press
To signal the machine to begin fax
reception, press
Storing auto dial numbers
2 When you hear the dial tone, dial
the number.
3 When you are ready to end the call,
press
2 Press
or
and press
Making a call using the phonebook
1 Press
(To open the machine’s phonebook
hold down
1 Press
to display “”
(Valid.).
3 Enter the name of the party (enter
each letter by repeatedly pressing
the number key shown for the letter
below).
=1
.)
= A, B, C, a, b, c, 2
2 Press
or until the name of the
party that you want to call appears.
= D, E, F, d, e, f, 3
= G, H, I, g, h, i, 4
= J, K, L, j, k, l, 5
3 Press
= M, N, O, m, n, o, 6
= P, Q, R, S, p, q, r, s, 7
Receiving a phone call
= T, U, V, t, u, v, 8
1 When the cordless handset rings,
pick it up and press
= W, X, Y, Z, w, x, y, z, 9
= special characters
to answer.
= /, space, +, @, -, $, &, %, 0
2 When you are ready to end the call,
press
Transferring a call
1 Press
, press or to select the
transfer destination (select
“HANDSET 0” for the machine), and
press
(Call).
2 When someone answers, press
to transfer the call.
=#,".:;!?'()_
To clear a mistake, press C.
4 Press
(Valid.).
5 Press the number keys to enter the
phone number (to insert a pause,
hold down
until a slash (/)
appears). When finished, press
(Valid.).
6 Press
or
to select an icon for
the number and press
(Valid.).
95
Guía de referencia rápida
Transmisión de Fax / de Fax a correo
electrónico
Coloque el documento (hasta 20 páginas)
mirando hacia abajo en el alimentador.
Cómo enviar un fax por marcación
normal
Levante el auricular u oprima
Marque el número de fax.
Espere a escuchar el tono de
recepción (si alguien contesta el
teléfono, pídale que oprima la tecla
Start).
Cómo programar números
Oprima
Introduzca el número de 2 dígitos de
marcación abreviada apropiado y
96
Oprima
hasta que
aparezca el número deseado.
, y a continuación
Oprima una tecla rápida no utilizada,
SPEED DIAL
Cómo buscar un número
(fax/correo electrónico)
Oprima
MENU
u oprima
e introduzca un
número de marcación abreviada de 2
dígitos no utilizado (01a 63). (Para
programar una dirección de correo
electrónico, también puede oprimir las
teclas A, B o C y continuar en el Paso
4.)
Cómo utilizar un número de Marcación
abreviada
(fax/correo electrónico)
Oprima
Oprima la Tecla rápida para el número
deseado.
SPEED DIAL
Modo TEL/FAX: El contestador
automáticamente contesta las llamadas y
recibe faxes. Las llamadas de voz se
indican con un sonido de timbre especial.
Cómo utilizar la Tecla rápida (fax/
correo electrónico)
hasta que aparezca el
modo de recepción deseado en el display.
oprima
SPEAKER
oprima
RESOLUTION/
RECEPTION MODE
Modo MANUAL: Contesta todas las
llamadas (incluso las de telefax)
levantando el auricular. Para que
comience la recepción del documento,
Oprima
Oprima
Modo AUTO: El contestador
automáticamente contesta las llamadas y
recibe faxes.
Cómo recibir faxes
Oprima
para fax o
correo electrónico.
Introduzca el número de fax o la
dirección de correo electrónico.
Oprima
Introduzca un nombre con las teclas
de letras.
Oprima
para
STOP
y a continuación
Utilización del teléfono inalámbrico
Para hacer una llamada
1 Levante el auricular inalámbrico y
oprima
Para indicar al aparato que comience a
recibir el documento, oprima
Cómo almacenar números de
marcación automática
2 Marque el número al escuchar el
tono de marcar.
1 Oprima
2 Oprima
3 Si está listo para terminar la
llamada, oprima
Para recibir un fax mediante el
auricular inalámbrico
o para mostrar
“” y oprima
(Valid.).
3 Ingrese el nombre de la persona
Para hacer una llamada usando el
directorio telefónico
(ingrese cada letra oprimiendo
repetidamente la tecla del número
mostrado para la misma).
1 Oprima
(Para abrir el directorio telefónico del
=1
aparato, mantenga oprimido
= D, E, F, d, e, f, 3
= A, B, C, a, b, c, 2
.)
= G, H, I, g, h, i, 4
2 Oprima
o hasta que aparezca el
número de la persona que busca.
= J, K, L, j, k, l, 5
= M, N, O, m, n, o, 6
3 Oprima
= P, Q, R, S, p, q, r, s, 7
= T, U, V, t, u, v, 8
Para recibir una llamada
= W, X, Y, Z, w, x, y, z, 9
1 Cuando suene el timbre del auricular
= caracters especiales
= /, espacio, +, @, -, $, &, %, 0
inalámbrico, levántelo y oprima
para contestar la llamada.
2 Si está listo para terminar la
llamada, oprima
Para transferir una llamada
1 Oprima
, oprima o para
seleccionar el destino al cual desea
transferir la llamada (seleccione
“HANDSET 0” del aparato), y
oprima
(Call).
2 Cuando alguien conteste, oprima
para transferir la llamada.
=#,".:;!?'()_
Para borrar un número equivocado,
oprima C.
4 Oprima
(Valid.).
5 Oprima las teclas de número para
ingresar el número de teléfono (para
ingresar un espacio, mantenga la
tecla
oprimida hasta que
aparezca una diagonal [/]). Cuando
haya terminado, oprima
(Valid.).
6 Oprima
o para seleccionar un
icono para el número y a
continuación oprima
(Valid.).
97
Index
Index
Anti Junk Fax, 64
Audible signals, 87
Auto Print Out (of Activity Report), 71
AUTO reception mode, 17, 57
Auto-dial numbers
Storing, 52
Using, 53
Batch page numbering, 56
Batteries
Disposal, 19
Installing, 18
Replacing, 19
Broadcasting, 60
Caller ID, 62
Caller ID list, 63, 74
Contrast, 50
Copies, 59
Cordless handset
Alarm clock, 26
Auto pickup / auto hang up, 32
Base priority, 37
Beeps, 30
Birthday alarm, 28
Call log, 25
Date and time setting, 31
Deleting, 36
Disabling fax reception, 37
Emergency number, 33
Faxes, receiving, 21
Hands-free mode, 20
Hold, 21
Language, 32
Locking the keypad, 33
Making a call, 20
Monitoring a room, 29
Phonebook, 23
Power, 20
98
Program key functions, 31
Receiver volume, 20
Receiving a call, 20
Registering (personal), 35
Registering (regular), 34
Renaming base, 38
Resetting, 38
Ring tones, 30
Silent mode, 30
System PIN, 35
Talking range, 18
Timer, 27
Transferring a call, 21
Voice box number, 32
Cordless handset charger, 18
Date, setting, 16
Destination List, 74
Dial Mode, 70
Dial tone detection, 72
Dialing
Automatic redialing, 55
Direct Keypad, 54
Normal, 51
Rapid Key, 54
Redialing, 55
Search, 54
Speed, 54
Direct Keypad Dialing, 54
Display messages, 63, 85
Document feeder, 49
Document restrictions, 49
Document sizes, 49
Duplex Scan, 64
ECM mode (Error Correction Mode), 71
E-mail addresses, storing, 44
E-mail message, 43, 46
E-mail options, 46
E-mail settings, 42, 43
E-mail subject, 43, 46
Index
Fax Signal Receive, 71
Fax to E-mail transmission, 45
File format, 43, 46
File name, 46
Fine Priority setting, 69
Network
Cable, 39
Checking connection, 40
Connecting to, 39
Problems, 41
Network Setting List, 74
Network settings, configuring, 48
Network settings, initializing, 48
Normal Dialing, 51
Number of Rings setting, 69
Group Keys, storing, 61
Group keys, using, 61
Group List, 74
Halftone setting, 50
Handset, 11
Handset receiver volume, 17
Hold, 58
Housing, cleaning, 77
Ink Save Mode, 73
Intercom, 22
IP address, 40, 48
Jams, clearing, 88
Key Tone setting, 72
Letters, entering, 8
Line error, 80
Loading paper, 12
Loading the document, 49
MANUAL reception mode, 17, 57
Memory full, 86
Memory, substitute reception to, 58
Ordering parts, 89
Packing tape, removing, 11
Page numbering, batch, 56
Paper jams, clearing, 88
Paper size setting, 73
Paper, loading, 12
Power cord, 13
Print cartridge
Aligning, 77
Cleaning nozzles, 77
Installing, 13
Wiping nozzles, 78
Print cartridge holder, wiping, 79
Pseudo Ring, 70
Quality Mode setting, 73
Rapid Key Dialing, 54
Rapid Key, using for e-mail, 46
Receive Fax to E-mail, 65
Receive Fax to E-mail List, 74
Receive Ratio setting, 72
Reception mode
AUTO, 17, 57
99
Index
MANUAL, 17, 57
TEL/FAX, 17, 58
Redialing, 55
Redialing, automatic, 55
Removing original document, 50
Resolution, 50
Ringer volume, 17
Scanning glass, cleaning, 76
Search Dialing, 54
Searching for stored e-mail address, 46
Secure Receive, 67
Sender address, 43
Sender name, 43
Sender’s name and fax number,
entering, 15
Setup List, 74
SMTP server, 43
Sort Copy, 73
100
Speaker volume, 17
Speed Dial number, using for e-mail, 46
Speed Dialing, 54
TEL. LINE jack, 15
TEL/FAX reception mode, 17, 58
Telephone line cord, 15
Time, setting, 16
Transaction Report, 75
Setting print condition, 70
Transferring calls, 21
Voice calls, 54
Web page in machine, 42
LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this Sharp
brand product (the "Product"), when shipped in its original container, will be free from defective
workmanship and materials, and agrees that it will, at its option, either repair the defect or replace
the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded
item(s) set forth below nor to any product the exterior of which has been damaged or defaced,
which has been subjected to misuse, abnormal service or handling, or which has been altered or
modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set
forth below and provided proof of purchase to the servicer.
To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and
exclusive of, all other warranties, express or implied. Specifically, ALL OTHER WARRANTIES
OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED. ALL EXPRESS AND IMPLIED
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE,
AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, under applicable state law, implied warranties may not validly be disclaimed or excluded, the duration of such
implied warranties is limited to the period(s) from the date of purchase set forth below.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties
other than those described above, or to extend the duration of any warranties beyond the time
period described above on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and
shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the
manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall
constitute full satisfaction of all claims, whether based on contact, negligence, strict liability or
otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects
in the Product which were caused by repairs or attempted repairs performed by anyone other than
an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or
consequential economic or property damage. Some states do not allow limits on warranties or on
remedies for breach in certain transactions; in such state the limits herein may not apply.
Your Product:
Warranty Period for this Product:
Additional items excluded
from warranty coverage:
Where to obtain service:
What to do to obtain service:
Personal Facsimile
Ninety (90) days parts and labor from date of purchase.
Any consumable items such as paper supplied with the
Product.
At a Sharp Authorized Servicer located in the United States.
To find out the location of the nearest Sharp Authorized Servicer,
call Sharp toll free at 1-877-794-8675.
Ship (prepaid) or carry in your Product to a Sharp Authorized Servicer.
Be sure to have proof of purchase available. If you ship or mail the
Product, be sure it is packaged carefully.
For product information or customer assistance, please visit http://www.sharpusa.com on the
World Wide Web or call 1-877-794-8675.
SHARP ELECTRONICS CORPORATION
Sharp Plaza,
Mahwah, New Jersey 07430-1163
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-1163
http://www.sharpusa.com
SHARP CORPORATION
FOR YOUR RECORDS
Please record the model number and serial number below, for easy
reference, in case of loss or theft. These numbers are located on the
rear side of the unit.Space is also provided for other relevant
information.
UX-D1200SE
Model Number
Serial Number
Date of Purchase
Place of Purchase
PRINTED IN THAILAND
(TINSE4529XHTA)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 104 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:e8c0dbf3-7985-4b18-aec3-0238d099014e Modify Date : 2006:08:22 17:26:57+02:00 Create Date : 2006:08:22 17:25:55+02:00 Metadata Date : 2006:08:22 17:26:57+02:00 Document ID : uuid:3aac9255-ac8c-48b7-9af2-2c11894ff71a Format : application/pdf Creator : Acrobat 5.0 Scan Plug-in for Windows Producer : Acrobat 5.0 Scan Plug-in for WindowsEXIF Metadata provided by EXIF.tools