Sharp HRO00068 Cellular Transceiver User Manual
Sharp Corporation Cellular Transceiver Manual 1
a href="https://usermanual.wiki/Sharp" itemprop="url">
Sharp >
Manual 2
| Download: | |
| Mirror Download [FCC.gov] | |
| Document ID | 947411 |
| Application ID | FYlgvZePkokzBBd+1eLquw== |
| Document Description | Manual 2 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 125.8kB (1572519 bits) |
| Date Submitted | 2008-05-27 00:00:00 |
| Date Available | 2008-07-11 00:00:00 |
| Creation Date | 2008-05-19 16:24:13 |
| Producing Software | Adobe Acrobat 8.1 |
| Document Lastmod | 2008-05-20 13:54:20 |
| Document Title | Manual 2 |
| Document Creator | Adobe Acrobat 8.1 Combine Files |
![337e15_dt25_7e.fm[337/346]Data Display/Edit/ManagementUse the FOMA terminal’s Infrared port from i-appli software to operate equipment supporting the infrared remote control such as TVs and VCRs. To use the infrared remote control function, download compatible i-appli software.Start i-appli software that supports Ir remote control functions, point the FOMA terminal’s Ir port to the front of the remote control sensor on the TV, VCR or other device to operate, and perform remote control operations. Actual operational methods will differ with each i-appli software application. Control devices from a distance of up to approximately 4 m (Distance will vary depending on the device, the ambient brightness and other factors).Use iC transmission to send and receive data to and from other FOMA terminals which also support iC transmission function. During iC transmission, the FOMA terminal status is the same as when outside the service area, such that making/receiving calls, i-mode, and data communications are not possible. iC transmission is not available while a call is in progress or the IC card is locked. Data that can be sent and received or operations when various lock functions are set are same as for Ir exchange (nP. 333). For details on starting iC transmission from i-appli nP. 251Note When i-appli To is set to [No], i-appli is not activated from Ir exchange. Cannot be activated as i-appli stand-by.Infrared remote controlUsing the infrared remote control functionRemote control operation15°Approx. 4 m15°Infrared portNote When in the Self mode, the Ir remote control function cannot be used. Depending on the device, operation may not run properly. Remote control operation may not run properly directly under fluorescent lights, near other equipment using infrared signals, or in areas of direct sunlight.iC transmissioniC transmissiondt25_E.book 337 ページ ２００８年５月１４日 水曜日 午後３時１１分](https://usermanual.wiki/Sharp/HRO00068.Manual-2/User-Guide-947411-Page-1.png)
![338e15_dt25_7e.fm[338/346]Data Display/Edit/Management Use while placing FeliCa mark (b) of receiving side FOMA terminal on that of sending side FOMA terminal as shown above. Do not move the FOMA terminal until all data are sent and received. Sending and receiving data may be difficult according to other party’s FOMA terminal. In such cases, make the clearance between the FeliCa marks (b) closer or farther, or move them up/down/left/right alternately. During iC transmission, FOMA terminal called LED flashes (nP. 121).Example: Phonebook1In stand-by, press a.2Select a name/C/[Send data]/[iC transmission]/[Send]/[Yes]. In the details screen: Press C/[Send data]/[iC transmission]/[Send]/[Yes].3Place FeliCa mark (b) on that of the other party’s FOMA terminal.1Place FeliCa mark (b) on that of the other party’s FOMA terminal.2Select [Yes]. Terminal security code and authentication password entry are required for sending or receiving all data items. The authentication password is a password exclusively for iC transmission. Before starting data transfer, the sender and receiver must enter the same user-specified four-digit password.Example: Phonebook1In stand-by, press a/C/[Send data]/[iC transmission]/[Send all].2Enter the terminal security code/t. Precautions for using iC transmission functionSending and receiving data individuallySending a single data item <Send>FeliCa markReceiving a single data item <Receive>Note When receiving phonebook, a confirmation message to store in PushTalk phonebook appears. To store, select [Yes]. When multiple phone numbers are stored, select the phone number. However, if the 2in1 mode is set to [B mode], the PushTalk phonebook confirmation screen does not appear.Sending and receiving all data itemsSending all data items <Send all>dt25_E.book 338 ページ ２００８年５月１４日 水曜日 午後３時１１分](https://usermanual.wiki/Sharp/HRO00068.Manual-2/User-Guide-947411-Page-2.png)