Sharp HRO00141 Mobile Terminal Equipment User Manual EB W51GJ Quick Tips indd

Sharp Corporation Mobile Terminal Equipment EB W51GJ Quick Tips indd

User Manual

1EB-W51GJEB-WX1GJ Quick TipsCharge the productThe product is not fully charged when you purchase it. Before using the product for the first time or when the battery has run low, charge the battery. ● Only use the specified AC adapter. Using an AC adapter other than the specified type may cause a fire or electric shock. ● If the product is not charged after the prescribed charging time has elapsed, stop charging. Continuing to charge the product may cause a fire or electric shock.1. Insert the power plug of the AC adapter into a power socket.2. Insert the connector of the AC adapter into the product's power/mini-USB connector.Power/mini-USB connectorWhen charging starts, the battery indicator on the front side of the product ( ) turns red. When the product is fully charged, the battery indicator turns off.3. When charging is finished, remove the connector of the AC adapter.4. Disconnect the AC adapter from the power socket.EB-W51GJ_Quick Tips.indd 1EB-W51GJ_Quick Tips.indd 1 2010/11/12 15:34:312010/11/12 15:34:31
2Turn on/off the power Turn on the power1. Press the power key.Rear side of product Turn off the power1. Hold down the power key for 2 seconds.The menu is displayed.2. Tap [電源OFF].3. Tap [OK].Setup STEP 1 : Configure wireless LAN settingsRegister information about the access point you will use. ● Users are liable for communication and connection charges required when using the wireless LAN function. ● These instructions cover the configuration procedure for an access point using AOSS.1. Turn on the power by pressing the power key.2. Tap [端末登録].3. Tap [AOSSで接続].4. Tap [AOSS]. Press the AOSS button on the access point device (the wireless LAN base station).5. When the [AOSS終了] screen appears, tap [OK]. The [登録処理開始] screen appears.EB-W51GJ_Quick Tips.indd 2EB-W51GJ_Quick Tips.indd 2 2010/11/12 15:34:322010/11/12 15:34:32
3 STEP 2 : Register the product1. On the [登録処理開始] screen, tap [登録開始]. After a few seconds, a user ID and password entry screen appears.2. Enter your user ID and password, and tap [ログイン].3. Tap [OK]. Setup is now complete.FCC Notice ● This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ● Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.Information to UserThis equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:EB-W51GJ_Quick Tips.indd 3EB-W51GJ_Quick Tips.indd 3 2010/11/12 15:34:322010/11/12 15:34:32
4Printed in China 6060A121530210L IAC HI c 1. Reorient/relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.4. Consult the dealer or an experienced radio/TV technician for help.FCC RF Exposure InformationYour device is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.EB-W51GJ_Quick Tips.indd 4EB-W51GJ_Quick Tips.indd 4 2010/11/12 15:34:322010/11/12 15:34:32

Navigation menu