Sharp HRO00217 Smart Phone User Manual

Sharp Corporation Smart Phone

User Manual

Download: Sharp HRO00217 Smart Phone User Manual
Mirror Download [FCC.gov]Sharp HRO00217 Smart Phone User Manual
Document ID2585947
Application IDEZA8W/68v6A97woFIJK7hQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize103.36kB (1291986 bits)
Date Submitted2015-04-15 00:00:00
Date Available2015-07-14 00:00:00
Creation Date2015-04-06 11:18:47
Document Lastmod2015-04-07 14:23:29
Document TitleUser Manual

General Inquiries

(Business hours: 9:00 a.m. to 8:00 p.m.)
0120-005-250 (toll free)
※ Service available in: English, Portuguese, Chinese,
Spanish.
※ Unavailable from part of IP phones.
(Business hours: 9:00 a.m. to 8:00 p.m. (open all year
round))
■From DOCOMO mobile phones
(In Japanese only)
Repairs
(Business hours: 24 hours (open all year round))
■From DOCOMO mobile phones
(In Japanese only)
(No prefix) 113 (toll free)
※ Unavailable from land-line phones, etc.
■From land-line phones (In Japanese only)
0120-800-000 (toll free)
※ Unavailable from part of IP phones.
(No prefix) 151 (toll free)
※ Unavailable from land-line phones, etc.
■From land-line phones (In Japanese only)
0120-800-000 (toll free)
※ Unavailable from part of IP phones.
● Please confirm the phone number before you dial.
● For Applications or Repairs and After-Sales Service, please contact the above-mentioned information center or the docomo
Shop etc. near you on the NTT DOCOMO website.
NTT DOCOMO website https://www.nttdocomo.co.jp/english/
SH-03G
For loss, theft, malfunction, and inquiries while overseas (24-hour reception)
■From DOCOMO mobile phones
International call access code
for the country you stay
-81-3-6832-6600* (toll free)
INSTRUCTION MANUAL
* You are charged a call fee to Japan when calling from a land-line phone, etc.
※ If you use SH-03G, you should dial the number +81-3-6832-6600 (to enter “+”, touch and hold “0”).
■From land-line phones 
Universal number
international prefix
-8000120-0151*
* You might be charged a domestic call fee according to the call rate for the country you stay.
※ For international call access codes for major countries and universal number international prefix, refer to DOCOMO website.
● If you lose your handset or have it stolen, immediately take the steps necessary for suspending the use of
the handset.
● If the handset you purchased is damaged, bring your handset to a repair counter specified by DOCOMO
after returning to Japan.
Don’t forget your mobile phone… or your manners!
When using your mobile phone in a public place, don’t forget to show common courtesy and consideration for others around you.
Sales:
Manufacturer: SHARP Corporation
’15.● (1st Edition)
15● TU*** 1
’15.●
SH-03G_E.book
0 ページ
2015年4月6日
月曜日
午前10時30分
Introduction
Thank you for purchasing “SH-03G”.
Be sure to read this manual before and during use to ensure proper operation.
Checking operation method
Basic package
Quick Start Guide (Basic package)
(in Japanese only)
This guide describes operations of basic functions.
User's Manual (App of the handset)
(in Japanese only)
This manual describes detailed guidance and
operations of functions.
In the home screen, [R]/[Instruction Manual]
User's Manual (in PDF format)
This manual describes detailed guidance and
operations of functions.
Download from the DOCOMO website
(https://www.nttdocomo.co.jp/english/support/
trouble/manual/download/index.html)
※ The URL and contents are subject to change without
prior notice.
The screens and illustrations in this manual are shown as
examples. The actual screens and illustrations may differ.
The explanations in this manual are based on the case when
the home app is docomo LIVE UX and the setting of kisekae is
[Red]. If you change the home app, operation procedures etc.
may be different from the explanations of this manual.
Note that “SH-03G” is referred to as “handset” in this manual.
This manual refers to microSD Card, microSDHC Card or
microSDXC Card as “microSD Card” or “microSD”.
Reproduction of this manual in part or in whole without prior
permission is prohibited.
The contents of this manual are subject to change without
prior notice.
SH-03G
(includes warranty)
Quick Start Guide
(in Japanese only)
TV/Mobacas antenna
cable SH01
Notes on usage
(in Japanese only)
For optional parts (sold separately) compatible with the handset,
refer to the DOCOMO website.
(https://www.nttdocomo.co.jp/product/option/)(in Japanese only)
SH-03G_E_01.fm
[0/12]
~~~~~ ~~~~~ ~~~~~ ~~~~~ ~~~~~
SH-03G_E.book
4 ページ
2015年4月6日
月曜日
午前10時30分
Precautions (ALWAYS FOLLOW
THESE DIRECTIONS)
Handling the handset, adapters, docomo
nano UIM card and TV/Mobacas antenna
cable (general)
Before use, read these “Precautions” carefully and use your
handset properly.
Keep this manual in a safe place for future reference.
These precautions contain information intended to prevent bodily
injury to the user and to surrounding people, as well as damage
to property, and must be observed at all times.
The following symbols indicate the different degrees of injury
or damage that may occur if information provided is not
observed and the handset is used improperly.
Danger
Danger
Do not use, store or leave the equipment in
locations subject to high temperatures (near a fire
or heating unit, in a kotatsu, under direct sunlight,
inside a vehicle on a hot day, etc.).
May cause fires, burns or bodily injury.
Do not place the equipment inside cooking
appliances such as microwave ovens or pressure
cookers.
This symbol indicates that
“death or serious bodily injury
may directly and immediately
result from improper use”.
Warning
This symbol indicates that
“death or serious bodily injury
may result from improper use”.
Caution
This symbol indicates that
“minor injury and/or property
damage may result from
improper use”.
May cause fires, burns, bodily injury or electric shock.
Do not attempt to disassemble or modify the
equipment.
May cause fires, burns, bodily injury or electric shock.
Do not get the equipment wet with water, drinking
water, pet urine, sweat, etc.
May cause fires, burns, bodily injury or electric shock.
Refer to the following for details on waterproofness.
nP. 10 “Waterproof”
Do not allow liquids (water, drinking water, pet
urine, sweat, etc.) to get inside the charger
terminal, external connector terminal or earphone/
microphone terminal.
The following symbols indicate specific directions.
Indicates a
prohibited action.
Indicates not to
handle the device
with wet hands.
Indicates not to
disassemble the
device.
Indicates that
instructions
specified are
compulsory (must
be followed).
Indicates not to use
the device near
water or get it wet.
Indicates that the
power cord must be
unplugged from the
outlet.
May cause fires, burns, bodily injury or electric shock.
Refer to the following for details on waterproofness.
nP. 10 “Waterproof”
Use only optional parts specified by NTT DOCOMO
for use with the handset.
May cause fires, burns, bodily injury or electric shock.
Warning
Do not subject the equipment to strong force or
impacts or throw it.
May cause fires, burns, bodily injury or electric shock.
Do not allow conductive materials (such as metal
objects and pencil lead) to come into contact with
the charger terminal, external connector terminal or
earphone/microphone terminal. In addition, do not
insert such objects.
“Precautions” is explained in the following six sections.
Handling the handset, adapters, docomo nano UIM card and TV/
Mobacas antenna cable (general). . . . . . . . . . . . . . . . . . . . . P. 4
Handling the handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 5
Handling adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 6
Handling docomo nano UIM card . . . . . . . . . . . . . . . . . . . . . P. 7
Handling near electronic medical equipment . . . . . . . . . . . . P. 7
Material list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 7
May cause fires, burns, bodily injury or electric shock.
Do not cover or wrap the equipment with bedding
etc. when using or charging.
May cause fires or burns.
Be sure to turn off the handset and not to charge
the battery in locations such as gas stations where
flammable gas may be generated.
May cause a gas explosion or fire.
To use Osaifu-Keitai in locations such as gas stations, be
sure to turn off the power in advance (If NFC/Osaifu-Keitai
lock is set, disable the lock before turning off the power).
SH-03G_E_01.fm
[4/12]
Contents/Precautions
SH-03G_E.book
5 ページ
2015年4月6日
月曜日
午前10時30分
If you notice anything unusual, such as an unusual
odor, overheating, discoloration or deformation
during use, charging or storage, immediately follow
the instructions below.
Unplug the power plug from the outlet or
cigarette lighter socket.
Turn off the handset.
Warning
Do not point the illuminated light directly at
someone's eyes. Especially when you shoot still
pictures or videos of young children, keep 1 m or
more distance from them.
May cause fires, burns, bodily injury or electric shock.
Do not use Mobile light near people's faces. Eyesight may
be temporarily affected leading to accidents.
Caution
Do not allow water or other liquids, metal,
flammable material or other foreign objects to enter
the docomo nano UIM card slot or microSD Card
slot on the handset.
Do not leave the equipment on unstable surfaces,
such as on a wobbly table or sloped surface.
May cause fires, burns, bodily injury or electric shock.
May fall and cause injury.
Do not shine the mobile light at anyone driving a
car or other vehicles.
Do not store the equipment in locations that are
subject to humidity, dust or high temperatures.
May prevent a driver from driving safely and cause a traffic
accident.
May cause fires, burns or electric shock.
Turn off the handset or set it to Airplane mode
before going aboard an airplane.
If being used by a child, have a guardian teach him/
her the proper handling procedures. In addition,
check that the child is using the equipment as
directed.
Since using the handset on airplanes is restricted, follow the
instructions given by the respective airlines.
May interfere with the operation of electronic devices
installed on the airplane.
If you commit a prohibited act while using the handset on an
airplane, you may be punished by law.
May result in bodily injury etc.
Keep the equipment out of the reach of young
children.
A young child may swallow the equipment, or suffer bodily
injury or electric shock.
Follow the instructions given by the respective
medical facility regarding the use of the handset in
a hospital.
Be very careful when using the handset connected
to an adapter continuously for a long time.
Turn off the handset in areas where the use of mobile
phones is prohibited.
May interfere with the operation of electronic devices and
electronic medical equipment.
The handset or adapter may become warm if you use an
app or video call, watch a video or TV, etc. for a long time
while charging.
Directly touching a warmed part for a long time may cause
redness, itching, rashes, etc. on your skin, or result in
low-temperature burns depending on your constitution or
health condition.
Keep the handset away from the ears during a call
in which hands-free is set or while the ringtone is
ringing.
When you attach the earphone/microphone etc. to
the handset to play games, music, etc., do not
make the volume too loud.
Handling the handset
Excessively high volume may damage your hearing.
Also, it may prevent you from hearing ambient sounds and
cause an accident.
The following is the type of the internal battery built into the
handset.
Label
Battery type
Li-ion00
Lithium-ion
If you have a weak heart, take extra precautions
when setting functions such as the vibrator and
ringtone volume for incoming calls.
May have harmful effects on your heart.
Danger
If you are using electronic medical equipment etc.,
contact the respective manufacturer or dealer to
check whether the operation of the equipment is
affected by signals.
Do not throw the handset into a fire or heat it.
The internal battery may catch fire, explode, overheat or
leak.
May interfere with the operation of electronic medical
equipment etc.
Do not apply excessive force on the handset such
as by puncturing it, hitting it with a hammer or
stepping on it.
Turn off the handset near high-precision electronic
devices or devices that use weak electronic
signals.
The internal battery may catch fire, explode, overheat or
leak.
May interfere with the operation of electronic devices.
※ Take particular care with the following devices
If the battery fluid etc. comes into contact with your
eyes, do not rub your eyes but immediately rinse
your eyes with clean water. Then seek prompt
medical treatment.
Hearing aids, implanted cardiac pacemakers, implanted
cardioverter-defibrillators or other electronic medical
equipment. Fire alarms, automatic doors, and other
equipment controlled by electronic signals. If you use an
implanted cardiac pacemaker, implanted
cardioverter-defibrillator or other electronic medical
equipment, contact the respective manufacturer or dealer to
check whether the operation of the equipment is affected by
signals.
May result in loss of eyesight.
SH-03G_E_01.fm
[5/12]
Contents/Precautions
SH-03G_E.book
6 ページ
2015年4月6日
月曜日
午前10時30分
If the battery fluid etc. leaks, do not get the liquid on
your skin (face, hands, etc.).
If the display part or camera lens is damaged, be
careful of broken glass and the exposed inside of
the handset.
May result in loss of eyesight or harm to your skin.
If the liquid etc. comes into contact with your eyes, mouth,
skin or clothes, immediately rinse the contacted area with
clean water.
If the liquid etc. comes into contact with your eyes or mouth,
seek medical treatment immediately after rinsing the
contacted area.
Tape is pasted on the back of the display while the surface
of the display is covered by a protective film so as to
minimize the possibility of glass scattering. However,
touching the broken or exposed parts may cause bodily
injury.
If the internal battery leaks or emits an unusual
odor, immediately stop using the handset and
move it away from any naked flames or fire.
Handling adapters
The battery fluid is flammable and could ignite, causing a
fire or explosion.
Warning
Caution
Do not use if the cord of the adapter is damaged.
May cause fires, burns or electric shock.
Do not swing the handset by its strap etc.
May hit you or others around you, resulting in an accident
such as bodily injury.
Never use the AC adapter in humid locations such
as a bathroom.
Do not use a damaged handset.
May cause fires, burns or electric shock.
May cause fires, burns, bodily injury or electric shock.
The DC adapter should only be used in negative
grounded vehicles. Never use it in positive
grounded vehicles.
For using a motion sensor and geomagnetic
sensor, check the safety around, hold the handset
and do not swing it more than necessary.
May cause fires, burns or electric shock.
Do not touch adapters if you hear thunder.
May cause an accident such as bodily injury.
May cause electric shock.
If the display is broken and the liquid crystal then
leaks, do not get the liquid on your skin (face,
hands, etc.).
Do not short-circuit the charger terminal when
connected to an outlet or cigarette lighter socket.
Also, do not allow any part of your body (hands,
fingers, etc.) to come into contact with the charger
terminal.
May result in loss of eyesight or harm to your skin.
If the liquid crystal comes into contact with your eyes or
mouth, immediately rinse the contacted area with clean
water and seek medical treatment.
If the liquid crystal comes into contact with your skin or
clothes, immediately wipe the liquid crystal off with alcohol
etc., and rinse the contacted area with soap etc.
May cause fires, burns or electric shock.
Do not place heavy objects on the cord of the
adapter.
The surface of the display is covered with a
protective film for ensuring the security
(shatterproof property of reinforced glass panel)
against any damages caused by the handset being
dropped or receiving a strong impact etc. Do not
remove the film forcibly or damage it.
May cause fires, burns or electric shock.
When plugging/unplugging an AC adapter into/from
the outlet, do not allow metallic straps or other
metallic objects to come into contact with the
prongs of the plug.
May cause fires, burns or electric shock.
Using the handset with the film removed may cause bodily
injury if the display gets damaged.
Do not apply excessive force on an adapter by
moving it up/down or to the left/right with the
adapter connected to the handset.
Do not dispose of the handset in ordinary garbage.
May cause fires or damage to the environment. Take the
unnecessary handset to a sales outlet such as a docomo
Shop or follow the instructions by a local institution that
handles used handsets.
May cause fires, burns, bodily injury or electric shock.
Never try to connect the microUSB plug when the
handset or AC adapter is wet.
Inserting the microUSB plug while the equipment is wet may
cause short circuit when you charge the battery and lead to
abnormal overheat, malfunction, fires or burns due to water,
foreign objects, etc. adhering to the handset or microUSB
plug though the handset provides waterproof performance.
If you use the handset in a vehicle, contact the
vehicle manufacturer or dealer to check whether
the operation of the vehicle is affected by signals.
May interfere with the operation of electronic equipment in
some vehicle models. In this case, stop using the handset.
Do not handle the cord or charger terminal of the
adapters or outlet with wet hands.
Use of the handset may cause itching, rashes,
eczema, etc. depending on your constitution or
health condition. If this occurs, immediately stop
using the handset and seek medical treatment.
May cause fires, burns or electric shock.
For details on materials of each part nP. 7 “Material list”
Look at the display in a well-lit place, keeping a
certain distance from the screen.
Otherwise, eyesight may be weakened.
SH-03G_E_01.fm
[6/12]
Contents/Precautions
SH-03G_E.book
7 ページ
2015年4月6日
月曜日
午前10時30分
Always use the specified power supply and voltage.
When using overseas, use the AC adapter that is
available overseas.
Handling near electronic medical equipment
Warning
Using the incorrect voltage may cause fires, burns or
electric shock.
AC adapter: 100V AC
DC adapter: 12/24V DC (for negative grounded vehicles
only)
AC adapter available overseas: 100 to 240V AC (Connect
only with a household AC outlet)
If you have electronic medical equipment such as
an implanted cardiac pacemaker or an implanted
cardioverter-defibrillator, always carry or use your
handset at least 15 cm away from your implant.
Electromagnetic signals may have harmful effects on the
operation of the electronic medical equipment.
If the fuse in the DC adapter blows, always replace
it with a specified fuse.
Patients receiving medical treatment away from a
medical facility (e.g. home treatment) who are using
electronic medical equipment other than implanted
cardiac pacemakers or implanted
cardioverter-defibrillators should consult the
respective manufacturers etc. for information
regarding the effects of signals on the equipment.
May cause fires, burns or electric shock. Refer to the
respective manuals for information on specified fuses.
Wipe off any dust on the power plug.
May cause fires, burns or electric shock.
Fully plug the AC adapter into the outlet.
May cause fires, burns or electric shock.
Electromagnetic signals may have harmful effects on the
operation of the electronic medical equipment.
Always grasp the adapters when unplugging the
power plug from the outlet or cigarette lighter
socket. Do not forcibly pull by the cord of the
adapter.
If there is any chance that the distance between the
handset and a person closest to you may get
shorter than 15 cm such as when you cannot freely
move around, set the handset not to emit radio
wave in advance (by setting Airplane mode, turning
the power off, etc.).
May cause fires, burns or electric shock.
When plugging/unplugging an adapter into/from
the handset, plug/unplug the adapter horizontally
and straightly, not applying excessive force on it.
Somebody nearby may be equipped with electronic medical
equipment such as an implanted cardiac pacemaker or an
implanted cardioverter-defibrillator. Electromagnetic signals
may have harmful effects on the operation of the electronic
medical equipment.
May cause fires, burns, bodily injury or electric shock.
Unplug the power plug from the outlet or cigarette
lighter socket when not using for a long time.
Follow the instructions given by the respective
medical facilities regarding the use of the handset
on their premises.
May cause fires, burns or electric shock.
Should water or other liquids enter the equipment,
remove the power plug from the outlet or cigarette
lighter socket immediately.
Material list
May cause fires, burns or electric shock.
Handset
Always unplug the power plug from the outlet or
cigarette lighter socket before cleaning the
equipment.
Part
May cause fires, burns or electric shock.
Caution
Do not touch the adapter for a long time when
connected to an outlet or cigarette lighter socket.
May cause burns etc.
Handling docomo nano UIM card
Caution
Display side
Surrounding area of display side
PA resin/UV coating for
surface
Upper surface
PC resin/UV coating for
surface
Bottom surface
Aluminum/Anodizing
Sides (Metal section)
Aluminum/Anodizing
Sides (Resin section)
PC resin
Grip sensor
Aluminum/Anodizing
Incoming/Charging illumination
PC resin
Back
Handset color White: PMMA +
PC resin/UV coating for
surface
Handset color Black, Red:
PET + PC + PET resin/Hard
coating for surface
Surrounding area of back
PA resin/UV coating for
surface
Be careful with the cutting surface when handling
the docomo nano UIM card.
May cause bodily injury.
SH-03G_E_01.fm
[7/12]
Material/Surface treatment
Reinforced glass/Shatterproof
sheet of surface
docomo nano UIM card slot
SUS/Ni plating
microSD Card slot
SUS/Ni plating
Contents/Precautions
SH-03G_E.book
8 ページ
Part
2015年4月6日
月曜日
午前10時30分
The adapter, docomo nano UIM card and TV/Mobacas antenna cable
are not waterproof. Do not use in humid or steamy areas such as
bathrooms and avoid exposing to rain and other forms of moisture. If
they are carried close to the skin, perspiration may cause internal
components to corrode and result in malfunction. Note that if a
problem is found to be due to moisture, the handset and parts are not
covered by warranty and in some cases may be irreparable. Even
when repairs are possible, repair charges will be incurred, since the
damage is not covered by warranty.
Material/Surface treatment
docomo nano UIM card/microSD
Card slot cover
PC resin/UV coating for
surface
Gasket of docomo nano UIM
card/microSD Card slot cover
Silicon rubber
Sticker indicating position for
inserting docomo nano UIM card/ PET resin
microSD Card
Clean only with a soft and dry cloth (such as the type used
for eyeglasses).
Tray for inserting docomo nano
UIM card
POM resin
IMEI plate
PET resin
Screw
SWCH16A/Plating
Power key
PC resin/Deposition
Side key
PC resin/Deposition
Camera panel
Reinforced glass/Printing on
the back
Decoration of camera
Aluminum/Anodizing
Dirty terminals may result in poor connections and loss of power or
insufficient battery charge. Keep the terminals clean with a dry cotton
swab etc.
Be careful with the terminals while cleaning them.
Fingerprint sensor
Epoxy resin/UV coating for
surface
Condensation formed due to rapid changes in temperature may
cause internal corrosion and lead to a malfunction.
Decoration of fingerprint sensor
Handset color White: SUS/Cr
deposition
Handset color Black: SUS/Ti
deposition
Handset color Red: SUS/TiAl
deposition
Mobile light
PC resin
Carrying the equipment in a tightly packed bag or sitting on it put in
your pocket may cause damage to the display, internal components,
etc. or result in a malfunction.
Keeping an external connector device plugged into the external
connector terminal or earphone/microphone terminal may cause
damage or a malfunction.
External connector terminal
SUS/Sn plating, Copper alloy/
Gold plating
May scratch it and cause a malfunction or damage.
Strap pin
PA resin
・ Forceful rubbing of the display with a dry cloth etc. may scratch its
surface.
・ Water drops, dirt, etc. left on the display may cause stains to form
on its surface.
・ Never use chemicals such as alcohol, thinners, benzene or
detergents, as these agents may erase the printing or cause
discoloration.
Occasionally clean terminals with a dry cotton swab etc.
Do not place the equipment near an air conditioning vent.
Do not apply excessive force on the handset etc. when
using it.
Do not rub or scratch the display with metal etc.
Read the respective user's guides supplied with supported
optional parts carefully.
TV/Mobacas antenna cable SH01
Part
Notes about the handset
Material/Surface treatment
Earphone/Microphone terminal
(Outer section)
Olefin system elastomer
Do not forcefully press the surface of the touch panel or
operate with a pointed object such as a fingernail, ballpoint
pen or pin.
Earphone/Microphone terminal
(Middle section)
PBT resin
May damage the touch panel.
Earphone/Microphone terminal
(Inner section)
PA resin
Earphone/Microphone terminal
(Metal section)
Ni base, Phosphor bronze/
Gold plating
Cord
Styrene system elastomer
Connector
Olefin system elastomer
Connector (Connection)
POM resin
Plug (Metal section)
Ni base, Brass/Gold plating
Plug (Resin section)
PP resin
Avoid using the handset in extremely high or low
temperatures.
Use the handset within the range of a temperature between 5°C and
35°C and a humidity between 45% and 85%.
Using the handset close to land-line phones, TVs, radios,
etc. may have harmful effects on the operation of such
equipment. Move as far away as possible from such items
before use.
Keep a separate memo noting information stored on the
handset.
DOCOMO shall not be liable for any loss of content.
Do not drop or otherwise subject the handset to severe
impact.
May cause a malfunction or damage.
When connecting an external connector device to the
external connector terminal or earphone/microphone
terminal, do not put it in obliquely and do not pull it while it
is plugged in.
Handling precautions
General notes
May cause a malfunction or damage.
The handset becomes warm during use or charging but this
is not a malfunction.
Do not leave the camera in direct sunlight.
SH-03G is waterproof, however, do not allow water to get
inside the handset and do not allow accessories or optional
parts to get wet.
May cause discoloration or burn-in of pixels.
Use the handset with the docomo nano UIM card/microSD
Card slot cover closed.
Dust, water, etc. may get inside and cause a malfunction.
SH-03G_E_01.fm
[8/12]
Contents/Precautions
SH-03G_E.book
9 ページ
2015年4月6日
月曜日
午前10時30分
Do not give a strong impact on the fingerprint sensor or
scratch the surface.
Keep a separate memo and note information stored on the
docomo nano UIM card.
May cause not only malfunction of the fingerprint sensor but also
disable authentication.
DOCOMO shall not be liable for any loss of content.
To protect the environment, please take any unneeded
docomo nano UIM cards to a sales outlet such as a docomo
Shop.
Do not damage, touch haphazardly or short-circuit the IC.
Clean the fingerprint sensor with a soft and dry cloth (such
as the type used for eyeglasses).
When the fingerprint sensor is dirty or gets wet on the surface, it
cannot read the fingerprint and may degrade the authentication
performance or cause a malfunction.
May cause data loss or a malfunction.
Do not drop or otherwise subject the docomo nano UIM
card to severe impact.
While using a microSD Card, do not remove the card or turn
off the handset.
May cause a malfunction.
May cause data loss or a malfunction.
Never place a magnetic card near the handset.
Never bend the docomo nano UIM card or place heavy
objects on it.
The stored magnetic data in cash cards, credit cards, telephone
cards, floppy disks, etc. may be erased.
May cause a malfunction.
Do not insert the docomo nano UIM card to the handset with
a label, sticker, etc. attached on the card.
Never place magnetized items near the handset.
Putting highly magnetized items closer may cause an error.
May cause a malfunction.
The internal battery is a consumable product.
Though the battery life varies with use, change the battery if the
battery life is extremely short even after being fully charged. For
details on replacing the internal battery, contact the number listed in
“Repairs” (in Japanese only) on the last page or a repair counter that
DOCOMO specifies.
Notes on using Bluetooth function
The handset supports the security function that meets the
Bluetooth specification for security during communication
using Bluetooth functions. However, the security may not
be sufficient depending on the configuration etc. Take care
of the security while making communication using
Bluetooth function.
Even if any leak of data or information occurs while making
communication using Bluetooth function, DOCOMO shall
not be liable for any loss of content.
Radio frequencies
In the home screen, [R]/[Settings]/[About phone]/
[Authentication] to confirm the radio frequencies the
Bluetooth function of the handset uses. The followings are
the descriptions:
Charge battery in areas where ambient temperature is
between 5°C and 35°C.
The battery life depends on the usage and deterioration of
the battery.
Avoid the following situations when the handset is stored.
 Storage with the internal battery fully charged (immediately after
charging is completed)
 Storage with no battery level (cannot turn the handset on)
May lower the performance or shorten the usable life of the internal
battery.
Approximately 40% is recommended as the proper battery level for
storage.
The surface of the handset uses the aluminum material.
Note that dent and abrasion are easily remained as
aluminum is a soft material.
ӱġ
Notes about adapters
Ӵġ ӵġ
Ӷġ
①
②
③
④
⑤
⑥
Charge the battery in areas where the ambient temperature
is between 5°C and 35°C.
Do not charge the internal battery in the following locations.
 Areas with high humidity or dust, or in areas exposed to frequent
vibrations
 Close to land-line phones, TVs, radios, etc.
Adapters may become warm during charging but this is not
a malfunction.
Do not use the DC adapter to charge the battery when the
car engine is not running.
2.4: This radio equipment uses the 2,400 MHz band.
FH: The modulation system is the FH-SS system.
1: The estimated coverage distance is 10 m or less.
XX: Another modulation system is used.
4: The estimated coverage distance is 40 m or less.
: All radio frequencies between 2,400 MHz and
2,483.5 MHz are used and the frequencies for mobile object
identifiers cannot be avoided.
Cautions on using Bluetooth devices
Bluetooth operates at radio frequencies assigned to the
in-house radio stations for a mobile object identifier that
have to be licensed and are used in production lines of a
factory, specific unlicensed low power radio stations, and
amateur radio stations (hereafter, referred to as “another
radio station”) in addition to industrial, scientific and
medical devices or home electric appliances such as
microwave ovens.
1. Before using the handset, make sure that “another radio
station” is not operating nearby.
2. If radio interference between the handset and “another
radio station” occurs, avoid interference by moving
immediately to another place or “turning off the power”.
3. Contact the number listed in “General Inquiries” on the
last page for further details.
May cause the car battery to run down.
When using an outlet with a feature to prevent the plug from
being removed accidentally, follow the instructions in the
outlet user's guide.
Do not subject to strong impacts. Also, do not deform the
charger terminals.
May cause a malfunction.
Notes about docomo nano UIM card
Do not apply unnecessary force when inserting/removing
the docomo nano UIM card.
Customer is responsible for malfunctions arising from
inserting docomo nano UIM card into a different IC card
reader/writer etc.
Always keep IC area clean.
Clean only with a soft and dry cloth (such as the type used
for eyeglasses).
SH-03G_E_01.fm
[9/12]
Ӳġ ӳġ
Contents/Precautions
SH-03G_E.book
10 ページ
2015年4月6日
月曜日
午前10時30分
Notes about wireless LAN (WLAN)
FeliCa and NFC reader/writer
The FeliCa, NFC reader/writer and P2P function of the
handset use weak radio waves whose handling does not
require a license of radio station.
The frequency in use is the 13.56 MHz band. When another
reader/writer or P2P function is being used nearby, keep
enough distance from it. Make sure that there is no radio
station using the same frequency band in the nearby area.
For use in an aircraft, contact the airline beforehand. Use of
the function may be restricted in some countries.
Check conditions such as regulations of the country/region
to use the function.
Wireless LAN (WLAN) uses radio waves to communicate
information. Therefore, it has an advantage of freely
connecting to the LAN within the service area. On the other
hand, if security setting is not set, it is possible for a
malicious third party to intercept the communication
contents or hack. It is recommended to set security setting
at your own risk and judgement.
Wireless LAN
Do not use wireless LAN near magnetic devices such as electric
appliances or AV/OA devices or in radio waves.
・ Magnetism or radio waves may increase noises or disable
communications (especially when using a microwave oven).
・ When used near TV, radio, etc., reception interference may occur
or channels on the TV screen may be disturbed.
・ If there are multiple wireless LAN access points nearby and the
same channel is used, search may not work correctly.
Caution
Never use the handset that is modified. Using a modified
device violates the Radio Law and/or the
Telecommunications Business Law.
Radio frequencies
In the home screen, [R]/[Settings]/[About phone]/
[Authentication] to confirm the radio frequencies the
WLAN-installed devices use. The followings are the
descriptions:
ӱġ
Ӳġ
The handset follows the regulations regarding the certification of
conformity with technical regulations for specific radio stations etc.
based on the Radio Law and authentication of conformity with
technical regulations for devices etc. based on the
Telecommunications Business Law, and the “Technical Conformity
Mark
” can be displayed on the electronic nameplate of the
handset as a proof. You can see it by operating as follows.
In the home screen, [R]/[Settings]/[About phone]/
[Authentication]
If the screws of the handset are removed and a modification is given
to the inside, the certification of conformity with technical regulations
etc. will become invalid. Never use the handset without the valid
certification etc. Doing so violates the Radio Law and/or the
Telecommunications Business Law.
ӳġ Ӵġ
ӵġ
①
②
③
④
⑤
2.4: This radio equipment uses the 2,400 MHz band.
DS: The modulation system is the DS-SS system.
OF: The modulation system is the OFDM system.
4: The estimated coverage distance is 40 m or less.
: All radio frequencies between 2,400 MHz
and 2,483.5 MHz are used and the frequencies for mobile object
identifiers can be avoided.
Available channels for the handset's wireless LAN are between 1 and
13. Note that other channel access points cannot be connected.
Available channels may vary depending on the country.
For use in an aircraft, contact the airline beforehand.
Be careful when using the handset while driving a motor
vehicle.
Using the handset in hand while driving is regarded as a punishable
act.
However, the punishment has no application in some cases such as
when rescuing sick and injured people or maintaining public safety.
Use the FeliCa reader/writer function only in Japan.
The FeliCa reader/writer function of the handset conforms to the
domestic radio wave standards. Using the function overseas may
result in punishment.
Cautions on using 2.4 GHz devices
WLAN-installed devices operate at radio frequencies
assigned to the in-house radio stations for a mobile object
identifier (radio stations requiring a license) used in
production lines of a factory, specific low power radio
stations (radio stations requiring no license), and amateur
radio stations (radio stations requiring a license) in addition
to industrial, scientific and medical devices or home electric
appliances such as microwave ovens.
1. Before using this device, make sure that the in-house
radio stations for a mobile object identifier, specific low
power radio stations and amateur radio stations are not
operating nearby.
2. If the device causes harmful radio interference to the
in-house radio stations for a mobile object identifier,
immediately change the radio frequency or stop use, and
contact the number listed in “General Inquiries” on the last
page for crosstalk avoidance, etc. (e.g. partition setup).
3. If the device causes radio interference to specific low power
radio stations for a mobile object identifier or amateur radio
stations, contact the number listed in “General Inquiries” on
the last page for further details.
Cautions on using 5 GHz devices
In the 5 GHz frequency band, three bands of 5.2 GHz/5.3
GHz/5.6 GHz band (W52/W53/W56) are available.
・ W52 (5.2 GHz band/36, 40, 44, 48 ch)
・ W53 (5.3 GHz band/52, 56, 60, 64 ch)
・ W56 (5.6 GHz band/100, 104, 108, 112, 116, 120, 124, 128,
132, 136, 140 ch)
Using 5.2 GHz/5.3 GHz band wireless LAN (W52/W53)
outdoors is prohibited by the Radio Law.
Never change the basic software improperly.
This may be regarded as a conversion of software and repairs may be
refused.
Waterproof
SH-03G is waterproof to IPX5*1 and IPX7*2 standards if the
docomo nano UIM card/microSD Card slot cover is securely
closed.
*1 IPX5 means that phone keeps functioning after being subjected
to a jet flow (12.5 liters/min) discharged from a nozzle (inner
diameter: 6.3 mm), from all directions (approximately 3 m from
the handset) for 3 minutes or more.
*2 IPX7 means that SH-03G phone keeps functioning after it is
slowly submerged to depth of 1 m in static tap water at room
temperature, left there for approximately 30 minutes and then
taken out.
What you can do with waterproof of SH-03G
You can call without using an umbrella in the rain (for rainfall of
approximately 20 mm per hour).
10
SH-03G_E_01.fm
[10/12]
Contents/Precautions
SH-03G_E.book
13 ページ
2015年4月6日
月曜日
午前10時30分
d microSD Card slot
e Earphone/Microphone terminal
f Microphone
Use when recording videos.
Use to measure ambient noises for communicating by making
your voices sound clear when using Noise suppression.
Use when talking to emopa.
g Back camera
h a mark
IC card is contained (It cannot be removed).
i Fingerprint sensor
Use to unlock the touch panel etc. by fingerprint
authentication.
j Strap hole
k Mouthpiece/Microphone
Use as a microphone when recording videos or talking to
emopa.
l Speaker
Ringtone, music, etc. can be heard from here.
The other party's voice can be heard from here during a
hands-free call.
m FOMA/Xi antenna*1
n Wi-Fi/Bluetooth antenna*1
o Wi-Fi antenna*1
p Air vent
A vent to remove excess air from the handset.
q TV antenna*1
Before Using the Handset
Part names and functions
*1 The antenna of back is built into the main body. At sides of the
handset, the metal sections of surface are used as the antenna.
Covering the antenna area with your hand may influence the
quality.
*2 Do not cover the sensor area with your hand or paste a sticker
etc. on the sensor area. The sensor may not work properly.
Earphone/Microphone terminal
For details on the corresponding earphone/microphone, refer to
the following website.
(http://k-tai.sharp.co.jp/support/d/sh03g/peripherals.html#!/
earphone_support)(in Japanese only)
Microphone
When using functions which support the microphone, do not
cover the hole of the microphone.
docomo nano UIM card
A docomo nano UIM card is an IC card that records personal
information, such as your phone number.
You cannot use functions such as the phone or packet
communication without inserting a docomo nano UIM card.
In Japan, you cannot call to the emergency number (110, 119 or
118) without inserting a docomo nano UIM card.
A docomo nano UIM card has a security code called PIN code
(nP. 72 “PIN code”).
The handset supports only docomo nano UIM card. If you have a
docomo mini UIM card, UIM or FOMA card, bring it to a docomo
Shop to replace.
Before inserting or removing the docomo nano UIM card, turn off
the power. Hold the handset securely with your hand.
1 GPS antenna*1
2 External connector terminal
3 Incoming/Charging illumination, Grip sensor
4 Proximity sensor/Brightness sensor*2
The proximity sensor detects the distance to the face and
prevents inadvertent operation of touch panel during a call.
The brightness sensor detects the brightness of the
surrounding area and adjusts the brightness of the backlight.
5 Earpiece/Microphone
Use as a microphone when talking to emopa.
6 Display/Touch panel
7 Front camera
8 docomo nano UIM card slot
The tray for inserting the docomo nano UIM card is stowed.
9 docomo nano UIM card/microSD Card slot cover
a Mobile light
b H: Power key
Use to turn the power on/off, etc.
Use to turn the display on/off.
c x/y: Volume UP/DOWN key
Adjusts the volume in each function.
13
SH-03G_E_02.fm
[13/28]
Before Using the Handset
SH-03G_E.book
15 ページ
2015年4月6日
月曜日
午前10時30分
Do not charge for a long time with the power left turned on. If the
handset is left turned on after charging is complete, the internal
battery charge level decreases.
In this case, an AC or DC adapter (sold separately) charges the
battery again. However, depending on the time when the
handset is disconnected from the AC or DC adapter, the battery
charge level may be low or the battery may only be usable for a
short time.
If the handset is left for a long time even after the charging is
completed, the battery level may decrease.
When the battery is empty and the handset is being charged, the
charging illumination may not illuminate immediately. However,
charging is in progress.
If the battery empty alert is displayed and the power cannot be
turned on, charge the battery for a while.
While charging, the handset may not be turned on even when the
charging illumination is illuminated in red. Charge longer and try
turning the power on again.
Frequently recharging the battery when its power is still
remaining enough may shorten the usable life of the internal
battery. It is recommended to use the battery to a certain level
(e.g. after the battery level decreases) before recharging.
When the battery becomes warm, charging may automatically
stop even if the battery has not been fully charged. Charging
automatically resumes after the temperature lowers to an
appropriate temperature.
If you watch Mobacas, receive content, etc. while charging, move
the handset as far away as possible from the power plug section
of the AC adapter.
If you watch TV etc. while charging for a long time, the usable life
of the internal battery may become shorter than estimated.
■ AC adapter and DC adapter
Refer to user's guide of AC Adapter 05 (sold separately) or DC
Adapter 04 (sold separately).
AC Adapter 05 covers from 100 to 240V AC.
The shape of the plug for the AC adapter is for 100V AC (for
domestic use). To use the AC adapter of 100 to 240V AC
overseas, a conversion plug adapter applicable to your country
of stay is required. Do not use a voltage converter for overseas
travel to charge the battery.
Charging with AC adapter/DC adapter
[Read the user's guides of AC Adapter 05 (sold
separately) and DC Adapter 04 (sold separately)]
Following operations describe how to charge with AC Adapter 05
or DC Adapter 04.
1 Insert the microUSB plug of the AC adapter/DC
adapter horizontally into the external connector
terminal on the handset with the side marked
with “B” turned down
: Check the direction (front or rear) of the microUSB plug and
insert it horizontally.
■ Estimated battery life when fully charged
Continuous
talk time
FOMA/3G
Approx. $$ min
GSM
Approx. $$ min
VoLTE (Voice call)
Approx. $$ min
Continuous
stand-by time
FOMA/3G
At rest: Approx. $$ hr (Preferred network type:
LTE/3G/GSM(Auto))
GSM
At rest: Approx. $$ hr (Preferred network type:
LTE/3G/GSM(Auto))
LTE
At rest: Approx. $$ hr (Preferred network type:
LTE/3G/GSM(Auto))
Mobacas
watching time
Approx. $$ min
TV watching
time
Full-Seg: Approx. $$ min
1Seg: Approx. $$ min
Charging
illumination
microUSB plug
External connector
terminal
Keep side marked with “B” down
2 When you erect the AC adapter power plug and
insert it into an outlet or insert the DC adapter
power plug into a car cigarette lighter socket,
the charging illumination illuminates and
charging starts
Power plug
For details on the battery life nP. 93 “Main specifications”
100V AC
outlet
Power plug
■ Internal battery usable life
Internal battery is a consumable product. Battery life per charge
is gradually reduced every time the battery is charged.
When battery life per charge is reduced to approximately half of
the default time, this means that the internal battery is
approaching the end of its usable life. In this case, it is
recommended to replace the battery as soon as possible. For
details on replacing the internal battery, contact the number
listed in “Repairs” (in Japanese only) on the last page or a repair
counter that DOCOMO specifies.
Cigarette
lighter socket
AC adapter
15
SH-03G_E_02.fm
[15/28]
DC adapter
Before Using the Handset
SH-03G_E.book
16 ページ
2015年4月6日
月曜日
午前10時30分
3 When charging is complete, the charging
illumination turns off
4 Remove the AC adapter power plug from the
outlet, or remove the DC adapter power plug
from the car cigarette lighter socket
5 Remove the microUSB plug of the AC adapter/
DC adapter horizontally from the external
connector terminal
Operations in touch panel lock screen
To set/disable the manner mode: y (for at least 2 seconds)
To turn on/off the mobile light: x (for at least 2 seconds)
To activate camera app: [K]
To activate しゃべってコンシェル (Shabette-Concier): [W]
To activate Clock: Touch the clock
To display the detailed information on notifications: Drag the
clock down
To display the status panel: Drag the status bar down
Note that inserting or removing the equipment forcibly may
cause damage to the external connector terminal and the
microUSB plug or result in a malfunction.
When using a DC adapter
The notifications are displayed in the lock screen of the touch
panel. You can make settings for displaying of notifications in
[When device is locked] (nP. 65 “Sound/notification”).
The DC adapter should only be used in negative grounded
vehicles (12 and 24V DC).
Do not use with the car engine shut off. May drain the car
battery.
If you set [エモパー設定] (emopa settings) to ON, various
information delivered by emopa is displayed under the clock.
You can check related websites etc. or make settings for
emopa by touching and holding a piece of information
(nP. 68 “emopa”).
The DC adapter fuse is a consumable product. For
replacement, purchase a new fuse at a nearest auto parts
retailer etc.
Refer to the user's guide of DC Adapter 04 for details.
Mobile light
The mobile light may be automatically turned off if you use the
handset for a long time or the handset becomes warm after the
mobile light is turned on. Also, you may not be able to use the
mobile light if the handset is warm.
Charging with Micro USB Cable 01
You can charge the handset by connecting the handset to a PC
with Micro USB Cable 01 (sold separately).
For details on connecting to a PC nP. 82 “Connecting the
handset and PC”
Basic operation
The followings describe basic operations of the handset such
as operations of the touch panel and navigation keys, and
operations for shooting screenshot.
Turning power on/off
■ Turning power on
1 H (for at least 2 seconds)
Operation of touch panel
: When you turn the power on for the first time, make the initial
settings (nP. 22 “Initial settings”).
The followings describe the operations to use the display
(touch panel).
Operations may differ depending on the function and screen in
use.
■ Turning power off
1 H (for at least 1 second)/[Power off]/[OK]
Cautions when using the touch panel
■ Turning power off forcibly
The touch panel is designed to be lightly touched with your
finger. Do not forcefully press with your finger or a pointed
object (fingernail, ballpoint pen, pin, etc.).
In the following cases, the touch panel may not work even if
you touch it. May cause a malfunction.
Operation with a gloved finger
Operation with the tip of a fingernail
Operation with foreign objects placed on the operation pad
Operation on the touch panel on which a protective sheet,
sticker, etc. is put
Operation while the touch panel is wet
Operation with fingers wet with sweat, water, etc.
You can forcibly turn the power off if the screen does not respond or
the power cannot be turned off.
1 H (for at least 8 seconds)
: Release your finger after the vibrator is activated to turn the
power off.
■ Turning display on/off
The display is turned off when H is pressed or the handset is not
in use for a set length of time.
Press H while the display is turned off to turn it on.
■ Touch panel lock
Operations may be interrupted if you touch an area other than a
confirmation screen or the status bar while the confirmation
screen etc. is displayed.
When the power or the display is turned on, the touch panel is
locked.
Touch [J] to unlock.
16
SH-03G_E_02.fm
[16/28]
Before Using the Handset
SH-03G_E.book
17 ページ
2015年4月6日
月曜日
午前10時30分
: If there are multiple apps supporting the user-aid function,
[q] is displayed and you can select an app to activate.
■ Touch
Touch a key or an item displayed on the screen and then release
your finger from it to select or set it.
■ Full-screen shrink mode
You can reduce the screen to operate the handset with one hand.
1 Slide any of the navigation keys up/slide it to
the left/right until [r]/[p] is displayed
: Repeat the same operation as that done when reducing the
screen to return it to the original size.
: Touch [C] to move the reduced screen or change the size.
■ Touch and hold
When you keep your finger on the touch panel, a menu may appear
depending on the function and screen in use.
■ Slide (Swipe)/Drag
You may not be able to reduce the screen depending on the
screen being displayed.
Move your finger while keeping it on the touch panel to scroll the
screen or move an icon, a widget, etc. to the desired position.
In addition, when you touch a menu or an item by mistake, move
your finger away from it to cancel the selection.
The Full-screen shrink mode is disabled if you switch to
horizontal display or the display is turned off while the
Full-screen shrink mode is set.
■ Retrieving menu
When you touch [{], slide the left edge of the screen to the right,
touch and hold the screen, etc., functions (menus) available in that
screen appear.
Example: App screen
■ Flick
Move your finger like sweeping the touch panel in the home screen
etc. to switch pages.
Menu
■ Pinch out/Pinch in
You may be able to zoom the screen in/out etc. by putting two
fingers on the touch panel and moving them with putting a distance
between two fingers apart (pinch out)/closer (pinch in) depending
on the function and screen in use.
■ Switching the settings
When a check box etc. is displayed beside the setting item, you can
set it enabled/disabled or ON/OFF by touching it.
Example: Call settings screen, Backup & reset screen
[0]: Enabled, [1]: Disabled
Operation while using function
■ Navigation keys
Use the navigation keys displayed at the bottom of the screen to
perform the basic operations.
[t]: ON, [u]: OFF
1 {/v: Back key/Close key
Return to the previous screen.
Close the keyboard.
2 |: Home key
Display the home screen.
3 }: Recent Apps key
Display Quick Launcher or Recent Apps (nP. 27 “Quick
Launcher”, P. 28 “Recent Apps”).
■ Using user-aid function
■ Vertical/Horizontal display
You can quickly activate apps supporting the user-aid function.
The screen display is switched when you tilt the handset.
Vertical/Horizontal display may not be switched even if the
handset is turned depending on the screen being displayed.
Vertical/Horizontal display is not switched if the handset is turned
while it is positioned parallel to the ground.
1 Slide any of the navigation keys up/slide it to
the left/right until [Google] is displayed
17
SH-03G_E_02.fm
[17/28]
Before Using the Handset
SH-03G_E.book
23 ページ
2015年4月6日
月曜日
午前10時30分
3 Select an item
Wi-Fi settings
 Network notification: Set whether to display a notification
icon when an open network is detected.
・ Set it after setting [Wi-Fi] is set to On.
 Scanning always available: Set whether to scan networks by
the location information service and other apps even when
[Wi-Fi] is set to Off.
 Wi-Fi sleep policy: Set whether to disconnect Wi-Fi when the
display is turned off.
 Avoid poor connections: Set whether to use the Wi-Fi
function only when stable Internet connections are available.
 Wi-Fi frequency band: Set the frequency band to use.
 Handover: Set whether to automatically switch access points
to use if you use the handset while moving.
 Mobile/Wi-Fi simultaneous use: Make settings for
simultaneous use of mobile and Wi-Fi networks.
 Install certificates: Install certificates.
 Wi-Fi Direct: Make settings for Wi-Fi Direct.
 Passpoint: Set whether to automatically connect to the
available Passpoint compatible access points when [Wi-Fi] is
set to On.
 MAC address: Confirm the MAC address.
 IP address: Confirm the IP address.
If you use Wi-Fi function of the handset, you can use mail or
Internet by connecting to access points of your home,
corporate network or public wireless LAN service.
Radio interference with Bluetooth devices
Wireless LANs (IEEE 802.11b/g/n) use the same frequency
band (2.4 GHz) as Bluetooth devices. Therefore, using the
wireless LAN device near a Bluetooth device may cause radio
interference, lowering of communication speed, noise or
connection failure. In this case, turn off the Bluetooth device or
keep the handset and the wireless LAN device at least
approximately 10 m away from the Bluetooth device.
Packet communication is also available while [Wi-Fi] is set to On.
Wi-Fi connection is prioritized while Wi-Fi connection is set, but
the connection is automatically switched to that of LTE/3G/GPRS
network once Wi-Fi connection is terminated. Note that packet
communication charges may be incurred in this case.
Refer to the manual of your wireless LAN base unit when using
the access point at home etc.
Operate access point registration near the access point.
If you use the docomo service by using Wi-Fi function, set a
docomo ID in advance. In the home screen, [R]/[Settings]/
[docomo service/cloud]/[docomo ID設定] (Set docomo ID) to
set it.
[Wi-Fi sleep policy]
In the following cases, approximately 15 seconds after display
is turned off, Wi-Fi connection is terminated.
When [When screen turns off] is set
When [Never when charging] is set and the handset is not
charged
The handset automatically connects to Wi-Fi again when the
display is turned on.
1 In the home screen, [R]/[Settings]/[Wi-Fi]
2 Set to On
3 Select an access point
: If you select an access point protected by security, enter the
password (security key) and select [CONNECT].
: To register access points manually: [z]/[Add network]/
enter the network name/set security/[SAVE]
: WPS compatible access points can be easily registered. In
the home screen, [R]/[Settings]/[Wi-Fi]/[z]/[Easy
Settings]/[WPS Push Button]/[WPS Pin Entry] to register an
access point.
: Alternatively, in the home screen, [R]/[Settings]/[Wi-Fi]/
[z]/[Easy Settings]/[AOSS] to connect to an access point.
Follow the instructions on the screen and operate after this
step.
[Handover]
You can set it only when you select [2.4 GHz only] of Wi-Fi
frequency band and [Setting OFF] of Simultaneous use mode
setting.
■ Mobile/Wi-Fi simultaneous use
You can make settings for the function to automatically switch to
mobile networks when communications with Wi-Fi access points
slow down (Smooth change mode) or the function to download
content at high speed using mobile and Wi-Fi networks at the same
time (Dual Speed mode).
Set [Wi-Fi] to On and connect to an access point in advance.
Since packet communication is also used when you use mobile
and Wi-Fi networks at the same time, packet communication
charges may be incurred.
When you select an access point and connect to it with a wrong
password (security key), [Avoided poor Internet connection],
[Authentication problem] or [Connected (Limited)] is displayed.
Confirm the password (security key). When [Avoided poor
Internet connection] or [Connected (Limited)] is displayed after
entering the correct password (security key), you may not have
acquired the correct IP address. Connect to the access point
again after confirming signal status.
1 In the home screen, [R]/[Settings]/[Wi-Fi]
2 [z]/[Advanced]
3 [Mobile/Wi-Fi simultaneous use]
4 Select an item
The registration process using WPS takes a few minutes. After
completion of the registration of the access point, check that the
proper connection to the access point is acquired.
 Simultaneous use mode setting: Set a mode to use.
 Advanced settings: Make settings for applicable access
points and apps, and inapplicable servers.
 Notes: Check the precautions.
: Touch []] of an item to display its explanations.
As for the manual registration of an access point, this function
supports WEP, WPA/WPA2 PSK and 802.1xEAP as the
security setting.
■ Detailed settings
■ Disconnecting
2 [z]/[Advanced]
1 In the home screen, [R]/[Settings]/[Wi-Fi]
2 Select the connected access point/
In the home screen, [R]/[Settings]/[Wi-Fi]
[Disconnect]
: Disconnect with the password retained. The access point
may be automatically connected again such as when the
display is turned on.
23
SH-03G_E_02.fm
[23/28]
Before Using the Handset
SH-03G_E.book
34 ページ
2015年4月6日
月曜日
午前10時30分
Entering touch-tone signals
Call
When using services in which you are required to enter
numbers additionally during a call, such as inquiry about the
balance in your bank account or ticket reservation, enter
pause (,)/wait (;) after entering a phone number to make a call
with an additional number added to the main phone number.
You can use the phone and phonebook, and make settings for
call, voice/answering memo, operations available when calls
are received, etc.
Making a call
■ Adding 2 seconds pause
1 In the home screen, []]/[Dial]
2 Enter a phone number
After making a call to a main phone number, the handset
automatically pauses for 2 seconds and an additional number is
sent.
: Always enter the city code, even when it is a local number.
: You can set to notify/not to notify the other party of your
phone number for each call by adding “186”/“184” to the
head of the phone number.
1 In the home screen, []]/[Dial]
2 Enter a phone number/[|]/[Add 2-sec pause]
3 Enter a number to send/[0]
■ Adding wait
After making a call to a main phone number, the handset
automatically waits and then a screen asking whether to send an
additional number is displayed. Touch [Yes] to send an additional
number.
1 In the home screen, []]/[Dial]
2 Enter a phone number/[|]/[Add wait]
3 Enter a number to send/[0]
4 [Yes] during the call
1 Call
Make a call. Also, if there are outgoing call history items,
touch it to enter the latest one when the phone number
has not been entered.
2 Favorites
Display the contacts set as favorites.
3 Delete
Delete an entered number.
Touch and hold it to delete all the entered numbers.
4 Register
5 Dial
Display the dial screen.
6 Outgoing/Incoming call history
7 Phonebook
Display the phonebook.
Video call
By using video call, you and the other party can talk on the
handset while seeing each other's image. Also, you can switch
between voice call and video call while talking on the handset.
Call charges and packet communication charges are incurred
when making a video call. In addition, packet communication
charges are incurred also when receiving a video call.
Quality of image may differ depending on the usage
environment because suitable communication levels are
applied according to the usage condition.
If you cannot switch to a video call during a voice call,
[Switching to video call failed] is displayed and the voice call
continues.
3 [0]
: To make a video call: [|]/[Video call]
4 [End call] to end the call
You cannot switch the audio output port to a Bluetooth device
during a video call. Set an output port after switching to a voice
call.
If you talk on the handset with your hair put between the
earpiece and your ear, the proximity sensor may not work
properly. The screen may be kept turned on and the call may be
interrupted when the screen is touched accidentally.
Be careful not to cover the speaker section during a video call.
The other party's voice may not be heard well.
While using video call in the background, your image is not sent
to the other party.
VoLTE
VoLTE enables you to use call and video call of high quality.
As for image displayed during a video call, since processes for
displaying image may differ depending on the model to use,
ranges of your image displayed on the handset may differ from
those displayed on the other party's device.
When you use VoLTE, the handset and the other party's device
need to satisfy the following conditions.
They are VoLTE compatible models
They are inside the Xi service area*
Preferred network type is set to [LTE/3G/GSM(Auto)]/[LTE/
3G] (nP. 85 “Preferred network type”)
Call mode setting is set to [VoLTE/3G] (nP. 37 “Call
settings/Other”)
* VoLTE is not available outside the Xi service area or during
international roaming.
34
SH-03G_E_04.fm
[34/40]
Call
SH-03G_E.book
35 ページ
2015年4月6日
月曜日
午前10時30分
Answering a call
Emergency call
Emergency calls
1 When a call is received, the ringtone sounds
Phone number
Police
110
Fire and ambulance
119
Marine emergency
118
and the incoming illumination flashes
Incoming
illumination
The handset supports “Emergency call location notification”.
When you make a call to an emergency number such as 110,
119 and 118, the information of your location (location
information) is automatically notified to the agency that has
received the emergency call (e.g. the police station). Depending
on your location and the reception status of the signal, the
agency that has received the emergency call may not be able to
confirm the exact location.
If you are not sending your caller ID by calling with “184” added
or other means, your location information and phone number
are not notified. However, if the agency that has received the
emergency call considers your location information and phone
number necessary for important purposes, such as life saving,
the agency may retrieve them regardless of your settings.
In addition, the area/timing to introduce “Emergency call
location notification” depends on the state of preparation in
each agency that receives emergency calls.
2 Answer the call
: Operate after touching [3].
Incoming voice call screen
Incoming video call screen
1 Reject call with SMS
Reject the incoming call and send a selected SMS
message to the other party.
2 Reject
Reject the incoming call.
3 Accept
Answer the call.
4 Accept voice
Answer the call using voice call.
5 Accept video
Answer the call using video call.
In Japan, you cannot make a call to the emergency number
(110, 119 or 118) when a docomo nano UIM card is not
inserted, while the PIN code is locked, from the PUK (PIN
Unlock Key) entry screen.
When calling 110, 119 and 118 from your handset, the police or
fire stations may return your call for verification purposes. State
that you are calling from a mobile phone, and give your phone
number and exact present location.
Remain stationary to ensure that the call is not disconnected
while you are on the line, and keep the handset turned on to
receive calls for approximately 10 minutes afterwards.
3 [End call] to end the call
Depending on the region, calls to the police or fire station of the
local area may not be made.
■ Answering a call while display is being turned on
When you make a call to the emergency number (110, 119 or
118) while Reject call setting is set, items of Reject call setting
are set to [OFF].
When a call is received while a screen other than lock screen of the
touch panel is being displayed, the incoming notification is
displayed. You can answer the call by using the notification.
Emergency call may not be available in some networks.
1 When a call is received, the incoming
You cannot make a video call to the emergency number (110,
119 or 118).
notification is displayed at the top of the screen
2 [Accept]/[Accept video]
International call (WORLD CALL)
: Touch the incoming notification to display incoming voice
call/video call screen.
: Flick the incoming notification to the left/right to hide the
notification.
WORLD CALL is an international calling service available from
DOCOMO devices in Japan.
To make an international call through a company other than
DOCOMO, contact the respective companies for instructions.
The caller ID may not be notified or displayed correctly
depending on overseas network operators. In this case, making
a call with incoming call history is not available.
■ Placing a call on hold
1 When a call is received, the ringtone sounds
and the incoming illumination flashes
[Calling Method]
When calling to a land-line phone: 010/country code/area
code (city code)/the other party's phone number/[0]
When calling to a mobile phone: 010/country code/the other
party's mobile phone number/[0]
・ As for the other parties' mobile phone numbers and area codes
(city codes) that begin with “0”, omit the first “0” when entering
(except some countries or regions such as Italy).
・ Alternatively, enter “009130-010” as usual or “+” instead of
“010”.
2 [|]/[Hold]
■ Answering a video call without sending your own
image
1 When a video call is received, the ringtone
sounds and the incoming illumination flashes
2 [|]/[Camera OFF response]
35
SH-03G_E_04.fm
[35/40]
Call
SH-03G_E.book
40 ページ
2015年4月6日
月曜日
午前10時30分
1 Image
2 Registered content
3 Notice
Make settings for Friends notice.
Available only when you are using cloud computing.
4 Edit
Using groups
1 In the home screen, select “ドコモクラウド”
(docomo cloud) folder/[docomo
phonebook]/[Group]
2 Use groups
■ Editing My profile
1 In the home screen, select “ドコモクラウド”
(docomo cloud) folder/[docomo
phonebook]/[My profile]
2 [Edit]
3 Set each item/[Save]
Backing up/Restoring phonebook
1 Account
2 Group icon
3 Group name
4 Add group
Add a group.
5 Groups
6 Number of contacts registered in the group
7 Sort
You can back up/restore the phonebook by using docomo
backup.
For details on backing up/restoring phonebook by using docomo
backup nP. 63 “Backing up to/Restoring from a microSD Card”
You cannot sort groups other than ones created with a docomo
account.
■ Grouping/Ungrouping contacts
1 In the home screen, select “ドコモクラウド”
(docomo cloud) folder/[docomo
phonebook]/[Group]
2 Select a group
3 [Delete member]/[Add member]
4 Select names/[OK]/[OK]
The group function is available on contacts created with a
docomo/Google account etc.
My profile
You can display your phone number registered on the docomo
nano UIM card. You can also register your name, mail
addresses, etc.
1 In the home screen, select “ドコモクラウド”
(docomo cloud) folder/[docomo
phonebook]/[My profile]
2 Check/Use the profile
40
SH-03G_E_04.fm
[40/40]
Call
SH-03G_E.book
41 ページ
2015年4月6日
月曜日
午前10時30分
5 Date and time of the message exchange
Mail/Web Browser
Check the message
You can send and receive messages using docomo mail, SMS,
Gmail, etc., and display websites using Chrome.
docomo mail
You can send and receive mails using mail address of
DOCOMO (@docomo.ne.jp). Pictograms and Deco-mail are
available. Automatic reception is also supported. Mails can be
easily transferred when you have lost the handset or changed
models since sent and received mails are saved on the
docomo mail server. Moreover, you can use the mailing
function on PCs, tablets, etc. if you use a docomo ID.
For details on docomo mail, refer to the DOCOMO website.
1 Destination/Sender
2 Phone call
3 Date and time of the message exchange
4 Message
1 In the home screen, [^]
: Follow the instructions on the screen and operate after this
step.
SMS
Replying message
1 In the home screen, [R]/[Messaging]
2 Select a thread
3 Enter the message/[@]
You can send and receive text messages with mobile phone
numbers serving as destinations.
※For details on the number of characters which can be sent and
received etc., refer to “Short Message Service (SMS)” on the
DOCOMO website.
You can also exchange messages with those who use network of
overseas network operators. Refer to the DOCOMO website.
Forwarding message
1 In the home screen, [R]/[Messaging]
2 Select a thread
3 Touch and hold a message/[Forward]
4 Enter the destination and message/[@]
1 In the home screen, [R]/[Messaging]
2 [0]
3 Enter the destination and message/[@]
You can switch Default SMS app to Hangouts
(nP. 70 “More”).
Deleting message
If destinations are devices owned by those who use network of
overseas network operators, enter “+”, the country code and the
recipient's mobile phone number. If the phone number begins
with “0”, omit the first “0”. Alternatively, enter “010”, the country
code and the phone number.
1 In the home screen, [R]/[Messaging]
2 Select a thread
3 Touch and hold a message/[Delete]/[Delete]
Half-width katakana and special symbols in SMS messages
may not appear correctly for recipient.
Deleting thread
SMS cannot be sent when “186” or “184” is added.
1 In the home screen, [R]/[Messaging]
: To delete all threads: [|]/[Delete all threads]/[Delete]
Displaying message
1 In the home screen, [R]/[Messaging]
2 Select a thread
Setting Messaging
: Messages are grouped into threads according to their
destinations/senders and displayed.
1 In the home screen, [R]/[Messaging]
2 [|]/[Settings]
3 Select an item
 SMS Enabled: Set an app to send and receive SMSs with.
 Delete old messages: When the number of saved messages
reaches its limit, messages are automatically deleted from
the oldest one.
 Text message limit: Set the number of messages to be saved
by thread.
 Preferred storage: Set a save destination for messages.
 Delivery reports: Notify you that sent messages have been
received every time a message is received.
 Manage SIM card messages: Manage messages saved on
the docomo nano UIM card.
1 Image
Displayed if an image of the other party is registered in
the phonebook. Touch to select and use an app
supporting the registered content of the phonebook. If the
person is not registered in the phonebook, you can
register the person in the phonebook after touching it.
2 Number of unread messages
3 Destination/Sender
4 Number of messages in thread
41
SH-03G_E_05.fm
[41/46]
Touch and hold a thread/[1]/[Delete]
Mail/Web Browser
SH-03G_E.book
42 ページ
2015年4月6日
月曜日
午前10時30分
2 Select a mail
Notifications: Notify you that messages have been received
on the status bar.
Sound: Set the ringtone to be rung when a message is
received.
Vibrate: Set the vibrator to be activated when a message is
received.
[Delivery reports]
When you send a message to mobile phones of other carriers,
the notification for confirming that it has been received may not
be sent to you.
1 Box name/Folder name being displayed
Touch [/] to switch or set folders/accounts.
2 Mails
The characters of sender or subject are displayed in thin
characters when a mail is read.
Touch images to checkmark the mails and you can set
them to be deleted/unread/read etc. collectively.
3 Mail search
4 Star icon
Use it as a mark indicating that the mail is special or
supposed to be dealt with later.
You can check starred mails in the Starred folder.
5 Newly compose mail
Email
You can send and receive mails by setting up a mail account
provided by a service provider.
Set up an account in advance (nP. 24 “Setting up mail
account”).
1 In the home screen, [R]/[Email]
2 [(]
3 Compose a mail
3 Check the mail
1 Account
If you set up multiple accounts, you can switch accounts.
2 Destination
When you enter part of a mail address or a name
registered in the phonebook, destination candidates are
displayed.
3 Subject
4 Message
5 File attachment
6 Add destinations
Touch it to add Cc or Bcc.
1 Subject
2 Sender/Destination
If the sender is registered in the phonebook, available
apps supporting the registered content of the phonebook
are displayed after touching the image. If the person is
not registered in the phonebook, you can register the
person in the phonebook after touching the image.
Touch the sender to switch detailed display/simplified
display.
3 Date and time of reception
Touch to display/hide the details of sender, destination or
data and time of reception.
4 Message
5 Attached file
6 Star icon
Use it as a mark indicating that the mail is special or
supposed to be dealt with later.
You can check starred mails in the Starred folder.
7 Menu of each mail
Touch to reply to all, forward or print by mail.
8 Reply
9 Delete
a Unread
4 [,]
Some receiving side models may not be able to receive the
subject completely.
Mails sent from a Gmail account are treated as ones from a PC.
When receiving side models set PC-mail rejection, mails cannot
be sent.
Mails that could not be sent for any reason will be saved in
Unsent as unsent mails.
Depending on the signal status etc., characters may not appear
correctly on the screen of the other party's device.
Attaching file
Files of up to approximately 5 MB can be attached. There are
no limits to the number of files to be attached.
Depending on the receiving side device, files may not be
received or correctly displayed/played. Also, the quality of
videos may deteriorate or videos may be converted to
continuous still pictures.
Displaying mail
The screen may appear different depending on the account to
use.
1 In the home screen, [R]/[Email]
42
SH-03G_E_05.fm
[42/46]
Mail/Web Browser
SH-03G_E.book
43 ページ
2015年4月6日
月曜日
午前10時30分
3 Compose a mail
Replying/Forwarding mail
1 In the home screen, [R]/[Email]
2 Select a mail
3 [)]
: To reply to all: [{] of each mail/[Reply all]
: To forward: [{] of each mail/[Forward]
1 Account
If you set up multiple accounts, you can switch accounts.
2 Destination
When you enter part of a mail address or a name
registered in the phonebook, destination candidates are
displayed.
3 Subject
4 Message
5 File attachment
6 Add destinations
Touch to add Cc or Bcc.
4 Compose a mail
1 Reply type
Touch to switch Reply/Reply all/Forward.
2 Destination
3 Message
4 Quote text
Touch to display/hide the mail of the sender.
You cannot operate it when forwarding mails.
5 Mail of sender
6 Subject
7 Respond inline
Enter the mail of the sender in the message.
4 [,]
Displaying mail
1 In the home screen, select “Google” folder/
[Gmail]
2 Select a thread
: In Gmail, mails are grouped into threads by reply and displayed.
If new mails are replied ones of an existing mail, they are
grouped into the same thread. A new thread is created for newly
composed mails or mails whose subjects have been changed.
5 [,]
Deleting mail
1 In the home screen, [R]/[Email]
: To delete selected mails: Touch the images of mails/[+]/
[OK]
2 Select a mail
3 [+]/[OK]
1 Box name/Label name being displayed
Touch [/] to switch or set displaying types/accounts.
2 Threads
The characters of destination/sender or subject are
displayed in thin characters when all mails in thread are
read.
Touch images to checkmark the threads and you can set
them to be archived/deleted/unread/read etc. collectively.
3 Mail search
4 Number of mails in thread
5 Star icon
Use it as a mark indicating that the thread is special or
supposed to be dealt with later.
You can check starred threads in the Starred folder.
6 Newly compose mail
Setting Email
1 In the home screen, [R]/[Email]
2 [/]/[Settings]
3 Select an item
General settings: Make settings for the whole Email.
Add account: Add account.
Privacy policy: Check the privacy policy.
: Select an account to make settings for the details on the
account such as Signature and Email notifications.
Gmail
Gmail is a mail service provided by Google.
Set up a Google account in advance (nP. 24 “Setting up
Google account etc.”).
1 In the home screen, select “Google” folder/
[Gmail]
2 [(]
43
SH-03G_E_05.fm
[43/46]
Mail/Web Browser
SH-03G_E.book
80 ページ
2015年4月6日
月曜日
午前10時30分
1 In the Bluetooth screen, [z]
2 Select an item
Using Bluetooth function
To register/connect a Bluetooth device, the Bluetooth passkey
may need to be entered. Before starting the registration, decide
one- to sixteen-digit number. Enter the same number on the
handset and the other party's Bluetooth device.
Set the other party's Bluetooth device to the registration stand-by
status in advance.
 Refresh: Search for the Bluetooth device.
 Rename this device: Change the handset's name.
 aptX: Set whether to use aptX®.
 Handsfree setting: Set whether to always have voices output
from the connected Bluetooth compatible hands-free device
during a voice call.
 Show received files: Display the history of data received via
Bluetooth connection.
1 In the home screen, [R]/[Settings]/
[Bluetooth]
2 Set to On
3 Select a Bluetooth device/[PAIR]
[aptX]
When you enable [aptX], sounds may not be output depending
on the Bluetooth device. In this case, disable [aptX].
: The confirmation screen for connection may be displayed.
: Entering the Bluetooth passkey may be necessary
depending on the other party's Bluetooth device. Also, some
Bluetooth devices may start connection after completing
registration.
: To search for Bluetooth devices: [z]/[Refresh]
: Touch [B] of a paired Bluetooth device to set name and
intended purpose of the other party's Bluetooth device.
Sending and receiving by Bluetooth
■ Sending data
Example: Still picture
1 In the home screen, [R]/[Contents
Manager]/[Photo]
You can connect up to seven Bluetooth devices at the same
time. Bluetooth devices may not work properly or the number of
Bluetooth devices which can be connected at the same time
may differ depending on the profile.
Touch and hold a still picture/[Share]/
[Bluetooth]
: Set the receiver's Bluetooth device to the reception stand-by
status.
If you fail to connect a Bluetooth device, connection may
become available after re-registering it.
3 Select a Bluetooth device to connect to
When [Bluetooth] is set to On, the handset is set to receive
registration requests/connection requests from other Bluetooth
devices. Make the setting for displaying the handset's
information on other Bluetooth devices in advance to allow the
handset to be searched for by other Bluetooth devices.
■ Receiving data
1 Data is sent from the sender's Bluetooth device
2 Drag the status bar down/select the incoming
notification/[ACCEPT]
While in connection stand-by, even if a connection request from
a Bluetooth device is received, connection may not be made
depending on the signal status etc.
3 Drag the status bar down/select the received
data
For details on the operations of the other party's Bluetooth
device, refer to the manuals of the Bluetooth device to be used.
Note that if you select [Delete and register] when receiving all
data, all data registered to the target function are deleted.
■ When receiving registration request from Bluetooth
device or connection request from unregistered
Bluetooth device
Receiving all data may not be available depending on the data
type.
When available space in the save destination becomes
insufficient while receiving data, the data being received to that
point are saved and receiving ends.
1 Registration request/Connection request from
Bluetooth device
2 Drag the status bar down/[Pairing request]/
[PAIR]
: When the confirmation screen about the settings on pairing
appears, select [PAIR].
: Entering the Bluetooth passkey may be necessary
depending on the other party's Bluetooth device.
: The confirmation screen for connection may be displayed.
■ Unregistering Bluetooth device
1 In the Bluetooth screen, [B] of the Bluetooth
device to unregister/[FORGET]
■ Disconnecting Bluetooth device
1 In the Bluetooth screen, select the Bluetooth
device to disconnect/[OK]
■ Setting Bluetooth
Set after setting [Bluetooth] to On.
80
SH-03G_E_09.fm
[80/81]
Data Communication
SH-03G_E.book
95 ページ
2015年4月6日
月曜日
午前10時30分
Specific Absorption Rate (SAR) of
Mobile Phones
European RF Exposure Information
Your mobile device is a radio transmitter and receiver. It is
designed not to exceed the limits for exposure to radio waves
recommended by international guidelines. These guidelines were
developed by the independent scientific organization ICNIRP and
include safety margins designed to assure the protection of all
persons, regardless of age and health.
The guidelines use a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit for mobile devices is
2 W/kg and the highest SAR value for this device when tested at
the ear is 0.791 W/kg* and when worn on the body is 0.399 W/kg*.
For body-worn operation, this mobile device has been tested and
meets the RF exposure guidelines when used with an accessory
containing no metal and positioning the handset a minimum of
1.5 cm from the body. Use of other accessories may not ensure
compliance with RF exposure guidelines.
As SAR is measured utilizing the devices highest transmitting
power the actual SAR of this device while operating is typically
below that indicated above. This is due to automatic changes to the
power level of the device to ensure it only uses the minimum level
required to reach the network.
This model SH-03G mobile phone complies with Japanese
technical regulations and international guidelines regarding
exposure to radio waves.
This mobile phone was designed in observance of Japanese
technical regulations regarding exposure to radio waves (*1) and
limits to exposure to radio waves recommended by a set of
equivalent international guidelines. This set of international
guidelines was set out by the International Commission on
Non-Ionizing Radiation Protection (ICNIRP), which is in
collaboration with the World Health Organization (WHO), and the
permissible limits include a substantial safety margin designed to
assure the safety of all persons, regardless of age and health
condition.
The technical regulations and international guidelines set out limits
for radio waves as the Specific Absorption Rate, or SAR, which is
the value of absorbed energy in any 10 grams of tissue over a
6-minute period. The SAR limit for mobile phones is 2.0 W/kg. The
highest SAR value for this mobile phone when tested for use at the
ear is $$ W/kg and when worn on the body is $$ W/kg (*2). There
may be slight differences between the SAR levels for each product,
but they all satisfy the limit.
The actual SAR of this mobile phone while operating can be well
below that indicated above. This is due to automatic changes to the
power level of the device to ensure it only uses the minimum
required to reach the network. Therefore in general, the closer you
are to a base station, the lower the power output of the device.
This mobile phone can be used in positions other than against your
ear. Please keep the mobile phone farther than 1.5 cm away from
your body by using such as a carrying case or a wearable
accessory without including any metals. This mobile phone satisfies
the technical regulations and international guidelines.
The World Health Organization has stated that “a large number of
studies have been performed over the last two decades to assess
whether mobile phones pose a potential health risk. To date, no
adverse health effects have been established as being caused by
mobile phone use.”
Please refer to the WHO website if you would like more detailed
information.
(http://www.who.int/docstore/peh-emf/publications/facts_press/
fact_english.htm)
Please refer to the websites listed below if you would like more
detailed information regarding SAR.
* The tests are carried out in accordance with international
guidelines for testing.
Declaration of Conformity
In some countries/regions including Europe, there are restrictions on the use
of 5GHz WLAN that may limit the use to indoors only.
If you intend to use 5GHz WLAN on the device, check the local laws and
regulations beforehand.
Hereby, Sharp Telecommunications of Europe Ltd, declares that this
SH-03G is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
A copy of the original declaration of conformity can be found at the
following Internet address:
(http://www.sharp.co.jp/k-tai/)(in Japanese only)
FCC Notice
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user's
authority to operate the equipment.
Ministry of Internal Affairs and Communications Website:
(http://www.tele.soumu.go.jp/e/sys/ele/index.htm)
Association of Radio Industries and Businesses Website:
(http://www.arib-emf.org/index02.html)(in Japanese only)
NTT DOCOMO, INC. Website:
(https://www.nttdocomo.co.jp/english/product/sar/)
SHARP Corporation Website:
(http://k-tai.sharp.co.jp/support/sar/)(in Japanese only)
*1 Technical regulations are defined by the Ministerial Ordinance
Related to Radio Law (Article 14-2 of Radio Equipment
Regulations).
*2 Including other radio systems that can be simultaneously used
with Xi/FOMA.
Information to User
This equipment has been tested and found to comply with the limits
of a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation; if this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
1. Reorient/relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
95
SH-03G_E_12.fm
[95/98]
Appendix/Index
SH-03G_E.book
96 ページ
2015年4月6日
月曜日
午前10時30分
4. Consult the dealer or an experienced radio/TV technician for
help.
Export Administration
Regulations
5 GHz WLAN Operation in USA
Within the 5.15-5.25 GHz band, UNII devices are restricted to
indoor operations to reduce any potential for harmful interference to
co-channel Mobile Satellite Services (MSS) operations.
FCC RF Exposure Information
Your handset is a radio transmitter and receiver.
It is designed and manufactured not to exceed the emission limits
for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government.
The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough
evaluation of scientific studies. The standards include a substantial
safety margin designed to assure the safety of all persons,
regardless of age and health.
The exposure standard for wireless handsets employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The
SAR limit set by the FCC is 1.6 W/kg.
The tests are performed in positions and locations (e.g., at the ear
and worn on the body) as required by the FCC for each model. The
highest SAR value for this model handset when tested for use at
the ear is 0.45 W/kg and when worn on the body, as described in this
user guide, is 0.47 W/kg.
For body worn operation, this phone has been tested and meets the
FCC RF exposure guidelines. Please use an accessory designated
for this product or an accessory which contains no metal and which
positions the handset a minimum of 1.5 cm from the body.
The use of accessories that do not satisfy these requirements may
not comply with FCC RF exposure requirements, and should be
avoided.
The FCC has granted an Equipment Authorization for this model
handset with all reported SAR levels evaluated as in compliance
with the FCC RF emission guidelines. SAR information on this
model handset is on file with the FCC and can be found under the
Display Grant section of (http://transition.fcc.gov/oet/ea/fccid/)after
searching on FCC ID APYHRO00217.
Additional information on Specific Absorption Rates (SAR) can be
found on the FCC website at (http://www.fcc.gov/encyclopedia/
radio-frequency-safety).
FCC ID Location
The device is electronically labeled and the FCC ID can be
displayed via the Device info & the Authentication under the Setting
menu.
The Japan Export Administration Regulations (“Foreign
Exchange and Foreign Trade Act” and its related laws) may be
applied to this product and its accessories under certain
conditions. The Export Administration Regulations may also
be applied. To export or reexport the handset and its
accessories, conduct all legally required procedures at your
own risk and expense. For details on the procedures, contact
the Ministry of Economy, Trade and Industry or the US
Department of Commerce.
Intellectual Property Right
Copyrights and rights of portrait
Data with third party copyrights such as text, images, music and
software that is downloaded via Internet websites, acquired by
TV, video, etc. or shot by the handset cannot be duplicated,
altered or publicly transmitted without rightful party's consent.
Only duplicating, quoting, etc. for personal use are permitted
under the Copyright Act.
Even if for personal use, filming and recording may be prohibited
for stage performances, shows, exhibitions, etc.
Also, shooting another's image or posting another's image on
Internet websites without his/her consent may constitute a
violation of one's right to his/her image.
Registered trademarks and trademarks
“FOMA”, “dmenu”, “dmarket”, “おサイフケータイ”, “ToruCa”,
“mopera U”, “Deco-mail”, “i-appli”, “i-mode”, “iD”, “WORLD
WING”, “WORLD CALL”, “iコンシェル”, “sp-mode”, “Xi”, “eトリ
セツ”, “しゃべってコンシェル”, “フォトコレクション”, “LIVE
UX”, the “ToruCa” logo, the “iD” logo, the “i-concier” logo, the
“Osaifu-Keitai” logo, the “Area Mail” logo, the “Media Player”
logo, the “Phonebook” logo, the “dmenu” logo, the “Anshin
Enkaku Support” logo, the “Shabette-Concier” logo, the “docomo
backup” logo, the “My magazine” logo, the “Shoplat” logo and the
“d book MyShelf” logo are trademarks or registered trademarks
of NTT DOCOMO, INC.
“Catch Phone (Call waiting service)” is a registered trademark of
Nippon Telegraph and Telephone Corporation.
Microsoft®, Windows®, Windows Media® and Windows Vista®
are trademarks or registered trademarks of Microsoft
Corporation in the United States and/or other countries.
Oracle and Java are registered trademarks of Oracle and/or its
affiliates.
Other names may be trademarks of their respective owners.
QR code is a registered trademark of Denso Wave Inc.
microSD Logo, microSDHC Logo and microSDXC Logo are
trademarks of SD-3C, LLC.
The handset features LCFONT, developed by Sharp
Corporation, to make the LCD easier to view and read. LCフォン
ト/LCFONT and
Corporation.
are registered trademarks of Sharp
OBEX™ is a trademark of Infrared Data Association®.
a is a registered trademark of FeliCa Networks, Inc.
96
SH-03G_E_12.fm
[96/98]
Appendix/Index
SH-03G_E.book
97 ページ
2015年4月6日
月曜日
午前10時30分
For DTS patents, see h
( ttp://patents.dts.com). Manufactured
under license from DTS Licensing Limited. DTS, the Symbol, &
DTS and the Symbol together are registered trademarks, and
DTS Sound is a trademark of DTS, Inc. © DTS, Inc. All Rights
Reserved.
This product is licensed under the MPEG-4 Systems Patent
Portfolio License for encoding in compliance with the MPEG-4
Systems Standard. An additional license and payment of
royalties are necessary in the following cases.
Data stored or replicated in physical media which is paid for on
a title by title basis.
Data which is paid for on a title by title basis and is transmitted
to an end user for permanent storage and/or use.
Such additional license may be obtained from MPEG LA, LLC.
Contact MPEG LA, LLC for additional details.
This product is licensed under the AVC patent portfolio license
for the personal and noncommercial use of a consumer to (i)
encode video in compliance with the AVC standard (henceforth
referred to as AVC video) and/or (ii) decode AVC video that was
encoded by a consumer engaged in a personal and
noncommercial activity and/or was obtained from a video
provider licensed to provide AVC video. No license is granted or
shall be implied for any other use. Additional information may be
obtained from MPEG LA, L.L.C.
See (http://www.mpegla.com)
This product is licensed under the VC-1 Patent Portfolio License
for the personal and noncommercial use of a consumer to (i)
encode video in compliance with the VC-1 standard (henceforth
referred to as VC-1 video) and/or (ii) decode VC-1 video that was
encoded by a consumer engaged in a personal and
noncommercial activity and/or was obtained from a video
provider licensed to provide VC-1 video. No license is granted or
shall be implied for any other use. Additional information may be
obtained from MPEG LA, L.L.C.
See (http://www.mpegla.com)
Content owners use Microsoft PlayReady™ content access
technology to protect their intellectual property, including
copyrighted content. This device uses PlayReady technology to
access PlayReady-protected content and/or WMDRM-protected
content. If the device fails to properly enforce restrictions on
content usage, content owners may require Microsoft to revoke
the device's ability to consume PlayReady-protected content.
Revocation should not affect unprotected content or content
protected by other content access technologies. Content owners
may require you to upgrade PlayReady to access their content. If
you decline an upgrade, you will not be able to access content
that requires the upgrade.
The abbreviations of operating systems (Japanese versions)
below are used in this manual.
 Windows 8.1 stands for Microsoft® Windows® 8.1, Microsoft®
and AOSS™ are the trademarks of BUFFALO INC.
Wi-Fi® is a registered trademark of Wi-Fi Alliance®.
Wi-Fi Direct™, Miracast™, Wi-Fi Protected Setup™ and Wi-Fi
Protected Setup logo are trademarks of Wi-Fi Alliance®.
The Wi-Fi Protected Setup Mark is a mark of the Wi-Fi Alliance.
Twitter and Twitter logo are trademarks or registered trademarks
of Twitter, Inc.
DLNA®, the DLNA Logo and DLNA CERTIFIED™ are
trademarks, service marks, or certification marks of the Digital
Living Network Alliance.
Sharp Corporation has acquired DLNA certification for the
device.
This product includes software developed by the OpenSSL
Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)
This product includes cryptographic software written by Eric
Young (eay@cryptsoft.com)
Portions Copyright © 2004 Intel Corporation
This product partly uses the software of Intel Corporation.
iWnn of OMRON SOFTWARE Co., Ltd. is used for conversion
methods for Japanese language, and for phrase prediction
methods for English.
iWnn © OMRON SOFTWARE Co., Ltd. 2008-2015 All Rights
Reserved.
iWnn IME © OMRON SOFTWARE Co., Ltd. 2009-2015 All
Rights Reserved.
Shin Go M, the font type installed in this product, is provided by
Morisawa & Company, Ltd.
* Shin Go is a registered trademark of Morisawa & Company,
Ltd.
aptX is a registered trademark of CSR plc.
DigiOn and DiXiM are trademarks of DigiOn, Inc.
VoiceText of HOYA Service Corporation is used for speech
synthesis. VoiceText is a registered trademark of Voiceware
co.,ltd.
“AQUOS”, “ZETA”, “Feel Home”, “Welcome Sheet”, “Slow Talk”,
“VeilView”, “Bright Keep”, “Sweep ON”, “NightCatch”, “エモパー/
emopa”, “S-Shoin” and “AQUOS” logo are trademarks or
registered trademarks of Sharp Corporation.
All other company names and product names are trademarks or
registered trademarks of the respective companies.
Windows® 8.1 Pro and Microsoft® Windows® 8.1 Enterprise.
Windows 8 stands for Microsoft® Windows® 8, Microsoft®
Windows® 8 Pro and Microsoft® Windows® 8 Enterprise.
Windows 7 stands for Microsoft® Windows® 7 (Starter, Home
Basic, Home Premium, Professional, Enterprise and Ultimate).
Windows Vista stands for Windows Vista® (Home Basic,
Home Premium, Business, Enterprise and Ultimate).
The Bluetooth word mark and logos are owned by the Bluetooth
SIG, INC. and any use of such marks by NTT DOCOMO, INC. is
under license. Other trademarks and trade names are those of
their respective owners.
Google, Google logo, Android, Google Play, Google Play logo,
Google+, Google+ logo, Gmail, Gmail logo, Google Calendar™,
Google Calendar logo, Google Maps™, Google Maps logo,
Google Chrome™, Google Chrome logo, Google Voice Search™,
Google Voice Search logo, YouTube, YouTube logo, Google
Drive, Google Drive logo and Google Now are trademarks of
Google Inc.
Others
FeliCa is a contactless IC card technology developed by Sony
Corporation. FeliCa is a registered trademark of Sony
Corporation.
Under the MPEG-4 Visual Patent Portfolio License, customers
have licensed permission for the following use of this product to
engage in non-profit personal use. Other uses are not permitted.
Encoding MPEG-4 standard video (henceforth referred to as
MPEG-4 video).
Decoding an MPEG-4 video that a customer not engaged in
personal commercial activities has encoded.
Decoding an MPEG-4 video obtained from a licensed provider.
For details on other intended uses, contact MPEG LA, LLC.
97
SH-03G_E_12.fm
[97/98]
Appendix/Index
SH-03G_E.book
105 ページ
2015年4月6日
月曜日
Using mobile phone with your manners!
Please be considerate of those around you when using the handset.
Turn off your handset in the following places
 When in an area where use is prohibited
When you are on an airplane or in a hospital, follow the instructions given by
the respective airlines or medical facilities. Turn off the handset in areas
where the use of mobile phones is prohibited.
Set Public Mode in the following places
 While driving
Using the handset in hand while driving is regarded as a punishable act.
However, some cases such as when rescuing sick and injured people or
maintaining public safety are exempted.
午前10時30分
Carrying out various procedures, checking
subscription, etc. online
From the handset dmenu/お客様サポート (Support)/ドコモオ
ンライン手続きの一覧をみる (View lists of the docomo online
procedure) (in Japanese only)
Some services may be charged when you access the website from
overseas.
From a PC My docomo (https://www.nttdocomo.co.jp/mydocomo/)
/ドコモオンライン手続き一覧 (Lists of the docomo online
procedure)/住所や契約内容の変更手続きがしたい (Change your
address or subscription) (in Japanese only)
※ You may not be able to access some website services due to system
maintenance, the content of your subscription, etc.
※ “Network security code” or “docomo ID/Password” is required to use
“ドコモオンライン手続き” (docomo online procedure).
 When in public places such as theaters, movie theaters or
museums
Using the handset in public places where you should be quiet results in
disturbing others.
Be aware of the place to use a mobile phone and the
volume of your voice and ringtone
 Be aware of the volume of your voice when using the handset in
quiet places such as restaurant and hotel lobby.
 Use in places where you do not block a passage in the town.
Be considerate of the privacy of the individuals around
you
 Please be considerate of the privacy of individuals around you
when taking and sending photos using camera-equipped
handset.
Do not use your smartphone while walking
 Using your smartphone while walking on a platform of a train
station, street, etc. may narrow your vision and cause a collision.
 Use your smartphone in a safe place after you stop walking.
These functions ensure manners in public
The handset has convenient functions such as setting not to
answer a call and setting to mute sound of the handset.
Manner mode (nP. 66 “Mode settings”)
Mutes sound of the handset.
※ However, the manner mode cannot mute camera shutter sound.
Public Mode (Phone OFF) (nP. 38 “Network service”)
When a call is received, a message stating that you are in a place that does
not allow the use of mobile phone is played and the call is automatically
disconnected.
Phone vibration (nP. 65 “Sound/notification”)
Notifies you of incoming call with vibration.
Answering memo (nP. 37 “Voice/Answering memo”)
Records callers' messages when you cannot answer the call.
※ Additionally, optional services such as Voice Mail Service
(nP. 38 “Network service”) and Call Forwarding Service
(nP. 38 “Network service”) are available.
We collect your unnecessary mobile phones and
other devices irrespective of carrier. Bring them to a
docomo Shop near you.
※ Intended devices: Mobile phone, PHS, battery
pack, charger and desktop holder (irrespective of
carrier)
SH-03G_E_14.fm
[105/105]
~~~~~ ~~~~~ ~~~~~
~~~~~ ~~~~~

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Create Date                     : 2015:04:06 11:18:47+09:00
Modify Date                     : 2015:04:07 14:23:29+09:00
Has XFA                         : No
Language                        : en
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2015:04:07 14:23:29+09:00
Format                          : application/pdf
Document ID                     : uuid:2f6350cf-8af3-4af8-9cb5-a4db974ddba2
Instance ID                     : uuid:7e2454b0-1733-4511-b86d-64180bd1bb0b
Page Mode                       : UseNone
Page Count                      : 25
EXIF Metadata provided by EXIF.tools
FCC ID Filing: APYHRO00217

Navigation menu