Sharp XV Z15000 Operation Manual GB User To The 7d80eb15 401d 481d 8058 56501956d7b4

User Manual: Sharp XV-Z15000 to the manual

Open the PDF directly: View PDF .
Page Count: 66

Download
Open PDF In Browser	View PDF

OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO

FRANÇAIS

XV-Z15000

PROJECTOR
PROJECTEUR
PROYECTOR
PROJETOR

ENGLISH

XV-Z15000

ESPAÑOL
PORTUGUÊS

SHARP CORPORATION

Printed in China
Imprimé en Chine
Impreso en China
Impresso na China
TINS-E012WJZZ
09P01-CH-NM

XVZ15000̲E̲US̲Hyo1-4.indd 1

2008/12/25 15:07:12

SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse.
Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or
and of the
same rating as above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut
off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a
serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue
: Neutral
Brown
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is
marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.
• The wire which is coloured blue must be connected to the terminal which is marked with the letter N
or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with the letter L
or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

XVZ15000̲E̲US̲Hyo1-4.indd 2

2008/12/25 15:07:12

Before using the projector, please read this operation manual carefully.

ENGLISH

Introduction
IMPORTANT
• For your assistance in reporting the loss or theft of
your Projector, please record the Serial Number located on the bottom of the projector and retain this
information.
• Before recycling the packaging, please ensure that
you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on
page 8.

WARNING:

Model No.: XV-Z15000
Serial No.:

High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain
or moisture.
See bottom of projector.

CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING:

The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.

This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

-1

XV-Z15000̲E̲US.indb 1

2008/12/25 14:25:12

INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the operation manual, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY

WARNING:

FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY

Declaration of conformity
SHARP PROJECTOR, MODEL XV-Z15000
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
TEL: 1-800-BE-SHARP (1-800-237-4277)

U.S.A. ONLY

PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal
of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at
1-800-BE-SHARP.
U.S.A. ONLY

Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 50.

This SHARP projector uses a DLP® chip. This very sophisticated panel contains 2,073,600 pixels (micromirrors). As
with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there
are certain acceptable tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life expectancy of the unit.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg

E.U. ONLY

-2

XV-Z15000̲E̲US.indb 2

2008/12/25 14:25:12

Preparing
Introduction
Contents ...........................................................3
How to Read this Operation Manual .............4
IMPORTANT SAFEGUARDS............................5
Accessories .....................................................8
Part Names and Functions .............................9
Using the Remote Control ............................12
Inserting the Batteries.......................................... 12
Usable Range ..................................................... 12

Quick Start
Quick Start .....................................................13

Using
Basic Operation
Turning the Projector On/Off ........................22
Connecting the Power Cord ................................ 22
Turning the Projector On ..................................... 22
Turning the Power Off
(Putting the Projector into Standby Mode) ..... 22

Image Projection ...........................................23
Adjusting the Projected Image ............................. 23
Keystone Correction............................................ 24
Auto V-Keystone Correction ................................ 25
Switching the Input Mode.................................... 26
Adjusting the Vertical and Horizontal Position of the Image ... 26
Displaying the Black Screen Temporarily ............. 27
Freezing a Moving Image..................................... 27
Auto Sync (Auto Sync Adjustment) ...................... 27
Selecting the Picture Mode ................................. 27
Displaying an Enlarged Portion of an Image ......... 28
Switching the Iris Setting ..................................... 28
Hiding the Menu Temporarily (Menu Hide) ........... 28
Switching the Eco+Quiet Mode ........................... 28
Resize Mode ....................................................... 29

Useful Features
Menu Bar Items .............................................31
Using the Menu Screen.................................34
Menu Selections (Adjustments) ........................... 34

Picture Adjustment (“Picture” Menu) ..........36
Selecting the Picture Mode ................................. 36
Adjusting the Image ............................................ 36
Switching the Iris Setting ..................................... 37
Eco+Quiet ........................................................... 37
Using the Advanced ............................................ 37
Correcting Gradation of Video (Gamma Correction) ... 37
Adjusting the Colors ............................................ 37
Adjusting the Bright Boost................................... 39

Reference
Appendix
Maintenance ..................................................47
Maintenance Indicators ................................48
Regarding the Lamp ......................................50
Lamp .................................................................. 50
Caution Concerning the Lamp............................. 50
Replacing the Lamp ............................................ 50
Removing and Installing the Lamp Unit................ 51
Resetting the Lamp Timer ................................... 52

Introduction

Contents
Setup
Setting Up the Projector ...............................15
Setting Up the Projector ...................................... 15
Standard Setup (Front Projection) ........................ 15
Projection (PRJ) Mode......................................... 16
Ceiling-mount Setup ........................................... 16
Screen Size and Projection Distance ................... 17

Connections
Samples of Cables for Connection ..............18
Connecting to Video Equipment ..................19
Connecting to a Computer ...........................20
Controlling the Projector by a Computer ....21

Selecting the Film Mode ...................................... 39
Setting Detail Enhancement ................................ 39
Reducing Image Noise (DNR) .............................. 39
Mosquito Noise Reduction (MNR) ....................... 39
Resetting All Adjustment Items ............................ 39

Computer Image Adjustment (“SIG-ADJ” Menu)...40
Adjusting the Computer Image ............................ 40
Setting the Resolution ......................................... 40
Auto Sync (Auto Sync Adjustment) ...................... 40
Signal Type Setting .............................................. 40
Setting the Video System .................................... 41
Setting the Video Setup....................................... 41
Adjusting the Dynamic Range ............................. 41
Signal Info ........................................................... 41

Adjusting the Projected Image (“SCR-ADJ” Menu) ...42
Setting the Resize Mode ..................................... 42
Adjusting the Image Position ............................... 42
Adjusting the Overscan ....................................... 42
Auto V-Keystone Correction ................................ 43
Keystone Mode Correction .................................. 43
Setting On-screen Display ................................... 44
Setting the Brightness of the Menu Screen.......... 44
Selecting the Background Image ......................... 44
Selecting the Menu Screen Position .................... 44
Reversing/Inverting Projected Images .................. 44
Selecting the On-screen Display Language ......... 44

Adjusting the Projector Function (“PRJ-ADJ” Menu) ...45
Setting Auto Power Off Mode .............................. 45
Setting the Power Save Mode (Economy Mode) ... 45
Setting One Touch Play, System Standby
and Input Name ............................................ 45
Setting the Demo Mode ....................................... 46
Selecting the Transmission Speed (RS-232C) ...... 46
Fan Mode Setting ................................................ 46
Returning the Default Settings ............................. 46
Lamp Timer (Life) ................................................ 46

Connecting Pin Assignments .......................53
RS-232C Specifications and Commands ....54
Computer Compatibility Chart .....................57
Troubleshooting .............................................58
For SHARP Assistance..................................60
Specifications ................................................61
Dimensions ....................................................62
Index ...............................................................63

-3

XV-Z15000̲E̲US.indb 3

2008/12/25 14:25:13

How to Read this Operation Manual
■ The specifications are slightly different, depending on the model. However, you can connect and operate all models
in the same manner.
• In this operation manual, the illustration and the screen display are simplified for explanation, and may differ slightly
from the actual display.

Using the Menu Screen

MENU button

Adjustment buttons
( //?/_)
Adjustment buttons
( //?/_)
RETURN button
ENTER button

ENTER button
RETURN button

Menu Selections (Adjustments)
• This operation can also be performed by using
the buttons on the projector.

1
2

Press MENU.
• The “Picture” menu screen for the selected input mode is displayed.

Press _ or ? to select the menu
screen to adjust on the menu
bar.

Buttons used in this operation

MENU button

Button used in this step
Example: “Picture” menu screen when
COMPONENT is selected for
input mode
Picture
SIG-ADJ
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
IRIS1 (Manual)
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset

SEL./ADJ.
RETURN

SCR-ADJ
PRJ-ADJ
Standard
0
0
0
0
0
0
0
0
High Brightness
On
Off

Menu bar

On-screen display

ENTER
END

-34

Info

............ Indicates safeguards for using the projector.

Note ............ Indicates additional information for setting up and operating the projector.

For Future Reference
Maintenance

P. 47

Troubleshooting

P. 58 and 59

Index

P. 63

-4

XV-Z15000̲E̲US.indb 4

2008/12/25 14:25:13

Introduction

IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE
HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for
its installation, use and servicing.
1. Read Instructions
All the safety and operating instructions should be read before
the product is operated.

2. Retain Instructions
The safety and operating instructions should be retained for
future reference.

3. Heed Warnings
All warnings on the product and in the operating instructions
should be adhered to.

4. Follow Instructions
All operating and use instructions should be followed.

5. Cleaning
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.

6. Attachments
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.

7. Water and Moisture
Do not use this product near water–for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.

8. Accessories
Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product. Any mounting
of the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer.

9. Transportation
A product and cart combination should
be moved with care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination
to overturn.

10. Ventilation
Slots and openings in the cabinet are provided for ventilation
to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.

11. Power Sources
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.

12. Grounding or Polarization
This product is provided with one of the following types of plugs.
If the plug should fail to fit into the power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.

13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.

14. Lightning
For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the cable system.
This will prevent damage to the product due to lightning and
power-line surges.

15. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.

16. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never
spill liquid of any kind on the product.

17. Servicing
Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.

18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the product to normal operation.
e. If the product has been dropped or damaged in any
way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.

19. Replacement Parts
When replacement parts are required, be sure the service
technician has used replace ment parts specified by the
manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock,
or other hazards.

20. Safety Check
Upon completion of any service or repairs to this product, ask
the service technician to perform safety checks to determine
that the product is in proper operating condition.

21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as
recommended by the manufacturer.

22. Heat
This product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.

-5

XV-Z15000̲E̲US.indb 5

2008/12/25 14:25:14

Observe the following safeguards when setting up your projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles
if lamp ruptures. In case of lamp
rupture, contact your nearest Sharp
Authorized Projector Dealer or Service
Center for replacement.
See “Regarding the Lamp” on page
50.

Caution concerning the setup of the projector
■ For minimal servicing and to maintain high image quality,
SHARP recommends that this projector be installed in
an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the vents and lens must be cleaned more often. As
long as the projector is regularly cleaned, use in these
environments will not reduce the overall operation life of
the unit. Internal cleaning should only be performed by
a Sharp Authorized Projector Dealer or Service Center.

Do not set up the projector in places exposed to
direct sunlight or bright light.
■ Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes out
the colors, making viewing difficult. Close the curtains
and dim the lights when setting up the screen in a sunny
or bright room.

Caution regarding placing of the projector
■ Place the projector on a level site within the adjustment
range (9 degrees) of the adjustment foot.

■ After the projector is purchased, a faint smell from the
vent may appear when the power is first turned on. This
is normal and is not a malfunction. It will disappear after
the projector is used for a while.

When using the projector in high-altitude areas
such as mountains (at altitudes of approximately 4,900 feet (1,500 meters) or more)
■ When you use the projector in high-altitude areas with
thin air, set “Fan Mode” to “High”. Neglecting this can
affect the longevity of the optical system.

Warning about placing the projector in a high
position
■ When placing the projector in a high position, make certain it is carefully secure to avoid personal injury caused
by the projector falling down.

Do not subject the projector to hard impact
and/or vibration.
■ Protect the lens so as not to hit or damage the surface
of the lens.

Rest your eyes occasionally.
■ Continuously watching the screen for long hours will
cause eye strain. Take regular breaks to rest your eyes.

Avoid locations with extremes of temperature.
■ The operating temperature of the projector is from 41°F
to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is from –4°F
to 140°F (–20°C to +60°C).

Do not block the exhaust and intake vents.
■ Allow at least 1113/16 inches (30 cm) of space between
the exhaust vent and the nearest wall or obstruction.
■ Ensure that the intake vent and the exhaust vent are not
obstructed.
■ If the cooling fan becomes obstructed, a protection
circuit will automatically put the projector into standby
mode to prevent overheat damage. This does not indicate a malfunction. (See page 48.) Remove the projector
power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust
vents are not blocked, plug the power cord back in and
turn on the projector. This will return the projector to the
normal operating condition.

Caution regarding usage of the projector
■ If you are not to use the projector for a long time or
before moving the projector, make certain you unplug
the power cord from the wall outlet, and disconnect any
other cables connected to it.
■ Do not carry the projector by holding the lens.
■ When storing the projector, ensure that you close the
lens shutter.
■ Do not expose the projector to direct sunlight or place
next to heat sources. Doing so may affect the cabinet
color or cause deformation of the plastic cover.

-6

XV-Z15000̲E̲US.indb 6

2008/12/25 14:25:14

■ When connecting a computer or other audio-visual
equipment to the projector, make the connections AFTER
unplugging the power cord of the projector from the AC
outlet and turning off the equipment to be connected.
■ Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.

Introduction

Other connected equipment

Info
• The cooling fan regulates the internal temperature,
and its performance is automatically controlled.
The sound of the fan may change during projector
operation due to changes in the fan speed. This
does not indicate malfunction.

Using the projector in other countries
■ The power supply voltage and the shape of the plug may
vary depending on the region or country you are using the
projector in. When using the projector overseas, make
sure you use an appropriate power cord for the country
you are in.

Temperature monitor function

■ If the temperature inside the projector increases, due
to blockage of the air vents, or the setting location,
the temperature warning indicator will blink. And if the
temperature keeps on rising, “
” will illuminate in
the lower left corner of the picture with the temperature
warning indicator blinking. If this state continues, the
lamp will turn off, the cooling fan will run and then the
projector will enter standby mode. Refer to “Maintenance
Indicators” on pages 48 and 49 for details.

• The DLP® logo and the DLP® medallion are registered trademarks of Texas Instruments.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other
countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
• All other company or product names are trademarks or registered trademarks of their respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or
discompile the contents thereof.

-7

XV-Z15000̲E̲US.indb 7

2008/12/25 14:25:14

Accessories
Supplied accessories

Remote control

Two AA size batteries

Operation manual

Power cord*
(1)

(2)

For U.S. and
Canada, etc.
(6' (1.8 m))

For Europe,
except U.K.
(6' (1.8 m))

(3)

(4)

For U.K. and
Singapore
(6' (1.8 m))

For Australia,
New Zealand and Oceania
(6' (1.8 m))

* Use the power cord that corresponds to the wall outlet in your country.

Note
x Codes in “< >” are Replacement parts codes.

Optional accessories
■ Lamp unit
■ Ceiling-mount adaptor
■ Ceiling-mount unit

■ 3 RCA to mini D-sub 15 pin cable (10' (3.0 m))

AN-K15LP
AN-60KT
AN-XGCM55 (for U.S.A. only)
AN-TK201
AN-TK202
AN-EP101B
(for U.S.A. only)
AN-C3CP2

Note
x Some of the optional accessories may not be available depending on the region. Please check with your
nearest Sharp Authorized Projector Dealer or Service Center.

-8

Numbers in

Introduction

Part Names and Functions
refer to the main pages in this operation manual where the topic is explained.

Projector
Top View

AUTO V-KEYSTONE
button

For turning the power on
and putting the projector
into standby mode.

13, 22

Power indicator

22, 48

Lamp indicator

22, 48

Temperature warning
indicator

RESIZE button

For switching the picture
size (NORMAL, STRETCH, etc.).

Exhaust vent

ENTER button

INPUT buttons (P/R)

Adjustment buttons (P/R/O/Q)

For selecting the appropriate picture.

For setting items selected or adjusted
on the menu.

For switching input mode.

For selecting menu items.

RETURN button
For returning to the previous menu
screen during menu operations.

MENU button
For displaying adjustment and setting
screens.

Zoom ring

14, 23

Remote control sensor

Intake vent

14, 23

HEIGHT ADJUST lever

22, 27, 51

Adjustment foot

For enlarging/
reducing the picture.

Focus ring
For adjusting the focus.

Lens shutter

Front View

Adjustment foot

PICTURE MODE button

Vertical keystone correction is
performed automatically.

STANDBY/ON button

14, 23

-9

XV-Z15000̲E̲US.indb 9

2008/12/25 14:25:16

Part Names and Functions (Continued)
Projector (Rear View)
Terminals
COMPONENT terminals
Terminal for connecting video
equipment with component
output terminal.

RS-232C terminal
Terminal for
controlling the
projector using a
computer.

18, 19

HDMI1, 2 terminals
Terminal for connecting video
equipment with HDMI output
terminal.

18, 19

Terminal for
connecting video
equipment with an
S-video terminal.

COMPUTER/COMPONENT
input terminal

18, 20

VIDEO input
terminal
Terminal for
connecting
video equipment.

Terminal for computer RGB and
component signals.

Remote control
sensor

S-VIDEO input
terminal

Carrying handle
For carrying the projector.

Security bar
Kensington Security
Standard connector

AC socket
Connect the supplied
power cord.

Using the Carrying Handle
When transporting the projector, carry it by the carrying handle on the side.
• Always close the lens shutter to prevent damage to the lens when transporting
the projector.
• Do not lift or carry the projector by the lens as this may damage the lens.

Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System.
Refer to the information that came with the system for instructions on how to use it to secure the projector.

-10

XV-Z15000̲E̲US.indb 10

2008/12/25 14:25:16

Introduction

Numbers in

refer to the main pages in this operation manual where the topic is explained.

Remote Control
STANDBY button
For putting the projector into
the standby mode.

HDMI1, 2, COMPONENT,
S-VIDEO, VIDEO,
COMPUTER buttons

13, 22

14, 26

AUTO SYNC button

PICTURE MODE button

IRIS 1, 2 buttons

IMAGE SHIFT button

ENTER button

MENU button

RESIZE button

ECO+QUIET button

For switching to the respective
input modes.

FREEZE button
For freezing images.

MAGNIFY buttons
For enlarging/reducing part of the
image.

KEYSTONE button
For entering the Keystone mode.

Adjustment
buttons (P/R/O/Q)

For selecting and adjusting menu
items.

RETURN button
For returning to the previous menu
screen during menu operations.

INPUT button
For switching input mode.

MENU HIDE button
For temporarily hiding menu
screen.

ON button

14, 22

For turning the power on.

For automatically adjusting images
when connected to a computer.
For selecting the appropriate
picture.

For switching “High Brightness”
and “High Contrast”.

For shifting images horizontally
and vertically.
For setting items selected or
adjusted on the menu.

For displaying adjustment and
setting screens.

For switching the picture size
(NORMAL, STRETCH, etc.).

For lowering the noise of the
cooling fan and extending the
lamp life.

-11

XV-Z15000̲E̲US.indb 11

2008/12/25 14:25:16

Using the Remote Control

Inserting the Batteries

Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.

Insert the supplied batteries and
put back the cover.
• Make sure the polarities correctly match
the m and n marks inside the battery
compartment.
• When putting back the cover, be sure that
the cover clicks in place and settles.

30°
30°

Usable Range

23' (7 m)
The remote control can be used to control
the projector within the ranges shown in the
illustration.
Remote
control
sensors

Note
• Remote control sensor is located on both the
front and rear of the projector.
• The signal from the remote control can be
reflected off a screen for easy operation. However, the effective distance of the signal may
differ depending on the screen material.

30°

23' (7 m)

When using the remote control:

• Be sure not to drop, expose to moisture or high
temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the projector away from the fluorescent lamp.

Remote control
signal transmitter
Remote control

Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below

Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them
using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept. Be
sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

-12

XVZ15000̲E̲US̲02.indd 12

2009/01/14 15:42:22

Quick Start
This section provides an example showing how to connect the projector to video equipment that has an HDMI
output terminal with a brief explanation of the steps from connection through to image projection.
For details, see the pages suggested in each step.

3, 7 STANDBY/ON

Quick Start

7 STANDBY button
3 ON button
5 Input Mode

button

Select buttons

6 Zoom ring
5 INPUT button
6 Focus ring

6 Adjustment feet

1. Place the projector facing a screen

Page 15

2. Connect the projector to the video equipment and plug
the power cord into the AC socket of the projector

Pages 18-22

3. Open the lens shutter fully and then turn the projector on
On the projector
2

STANDBY/ON button

Page 22

Press STANDBY/ON on the projector or ON on the
remote control pointing the remote control towards
the projector.
On the remote control
2

ON button

-13

XV-Z15000̲E̲US.indb 13

2008/12/25 14:25:17

Quick Start (Continued)

4. Turn the video equipment on and start playback
Playback

5. Select the input mode

Page 26

Press HDMI1 on the remote control to select “HDMI1” for the Input mode.

HDMI1 button

HDMI1
Component
1080P

• Press HDMI1, HDMI2, COMPONENT, S-VIDEO, VIDEO and COMPUTER on the remote control to
switch the Input mode.
• Press P or R to select your desired input mode when you press INPUT on the remote control or on the
projector.

6. Adjust the projector angle, focus and zoom
1. The focus is adjusted by
rotating the focus ring.

Focus ring

2. Zooming is adjusted by
rotating the zoom ring.

Page 23
3. The projector angle is
adjusted by using the
adjustment feet.

Zoom ring

Adjustment feet
• When the image is distorted
trapezoidally, the keystone
correction is needed.
(See page 24.)

7. Turn the power off

Page 22

Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again
while the confirmation message is displayed, to put the projector into standby mode.
On the projector
1

STANDBY/ON button

On the remote control

On-screen display

STANDBY
button

-14

XV-Z15000̲E̲US.indb 14

2008/12/25 14:25:18

Setting Up the Projector
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and
level.

Note
• The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly
on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when
setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.

Setup

Standard Setup (Front Projection)

■ Place the projector at the required distance from the screen according to the desired picture size.

Example of standard setup
Side View

Screen

H
Lens center

90°

L
Note
• Refer to page 17 for additional information concerning “Screen Size and Projection Distance”.

-15

XV-Z15000̲E̲US.indb 15

2008/12/25 14:25:18

Setting Up the Projector (Continued)
Projection (PRJ) Mode
The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ Mode in “SCR-ADJ” menu. See page 44.)

■ Ceiling mounted, front projection

■ Table mounted, front projection

Menu item ➞ “Ceiling + Front”

Menu item ➞ “Front”

■ Ceiling mounted, rear projection
(with a translucent screen)

■ Table mounted, rear projection
(with a translucent screen)

Menu item ➞ “Rear”

Menu item ➞ “Ceiling + Rear”

Ceiling-mount Setup

■ It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this installation. Before
mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain
the recommended ceiling-mount adaptor and unit (sold separately).

Indication of the Projection Image Size and Projection Distance
For details, refer to “Screen Size and Projection Distance” on page 17.
Example : When using a wide screen (16:9)

Picture Size
500"

436
200"

174

100"
80"

"×98
"

87"
70"× ×49"
39"

Projection
Distance

35"×
20"

(1 1
5. '6
7 "
m
)

(1 4'1
.3 "
m ~4
~ '9
1 "
(2 8' .4
.5 3" m)

m ~
1 ~ 9
(3 0'4 2 '6"
.1 " .9
m~ m
~ 11 )
2 3 '1
(6 0' .6 1"
.3 7" m
m ~ )
~ 23
7. '9
2 "
m
5 )

40"

"×2
45"

-16

XV-Z15000̲E̲US.indb 16

2008/12/25 14:25:19

Screen Size and Projection Distance
When using a wide screen (16:9): In case of displaying the 16:9 picture on the whole of the 16:9 screen.
Diag. (x)
500" (1270 cm)
400" (1016 cm)
300" (762 cm)
250" (635 cm)
200" (508 cm)
150" (381 cm)
120" (305 cm)
100" (254 cm)
80" (203 cm)
60" (152 cm)
40" (102 cm)

Picture (Screen) size
Width
436" (1107 cm)
349" (886 cm)
261" (664 cm)
218" (553 cm)
174" (443 cm)
131" (332 cm)
105" (266 cm)
87" (221 cm)
70" (177 cm)
52" (133 cm)
35" (89 cm)

Height
245" (623 cm)
196" (498 cm)
147" (374 cm)
123" (311 cm)
98" (249 cm)
74" (187 cm)
59" (149 cm)
49" (125 cm)
39" (100 cm)
29" (75 cm)
20" (50 cm)

Projection distance [L]
Minimum [L1]
Maximum [L2]
51'6" (15.7 m)
—
41'2" (12.6 m)
47'6" (14.5 m)
30'11" (9.4 m)
35'8" (10.9 m)
25'9" (7.9 m)
29'8" (9.1 m)
20'7" (6.3 m)
23'9" (7.2 m)
15'5" (4.7 m)
17'10" (5.4 m)
12'4" (3.8 m)
14'3" (4.3 m)
10'4" (3.1 m)
11'11" (3.6 m)
8'3" (2.5 m)
9'6" (2.9 m)
6'2" (1.9 m)
7'2" (2.2 m)
4'1" (1.3 m)
4'9" (1.4 m)

The formula for picture size and projection distance
[Feet/inches]
[m/cm]
L1 (ft) = 0.0314 x / 0.3048
L1 (m) = 0.0314 x
L2 (ft) = 0.0362 x / 0.3048
L2 (m) = 0.0362 x
H (in) = 0.2 x / 2.54
H (cm) = 0.2 x

Setup

x : Picture size (diag.) (in/cm)
L : Projection distance (ft/m)
L1 : Minimum projection distance (ft/m)
L2 : Maximum projection distance (ft/m)
H : Distance from the lens center to the bottom of the image (in/cm)

Distance from the lens center to
the bottom of the image [H]
39 3/8" (100 cm)
31 1/2" (80 cm)
23 5/8" (60 cm)
19 11/16" (50 cm)
15 3/4" (40 cm)
11 13/16" (30 cm)
9 29/64" (24 cm)
7 7/8" (20 cm)
6 19/64" (16 cm)
4 23/32" (12 cm)
3 5/32" (8 cm)

When using a normal screen (4:3) and projecting 4:3 image (NORMAL Mode)
Diag. (x)
400" (1016 cm)
300" (762 cm)
250" (635 cm)
200" (508 cm)
150" (381 cm)
120" (305 cm)
100" (254 cm)
80" (203 cm)
70" (178 cm)
60" (152 cm)
40" (102 cm)

Picture (Screen) size
Width
320" (813 cm)
240" (610 cm)
200" (508 cm)
160" (406 cm)
120" (305 cm)
96" (244 cm)
80" (203 cm)
64" (163 cm)
56" (142 cm)
48" (122 cm)
32" (81 cm)

Height
240" (610 cm)
180" (457 cm)
150" (381 cm)
120" (305 cm)
90" (229 cm)
72" (183 cm)
60" (152 cm)
48" (122 cm)
42" (107 cm)
36" (91 cm)
24" (61 cm)

Projection distance [L]
Minimum [L1]
Maximum [L2]
50'5" (15.4 m)
—
37'10" (11.5 m)
43'7" (13.3 m)
31'6" (9.6 m)
36'4" (11.1 m)
25'3" (7.7 m)
29'1" (8.9 m)
18'11" (5.8 m)
21'10" (6.6 m)
15'2" (4.6 m)
17'5" (5.3 m)
12'7" (3.8 m)
14'6" (4.4 m)
10'1" (3.1 m)
11'8" (3.5 m)
8'10" (2.7 m)
10'2" (3.1 m)
7'7" (2.3 m)
8'9" (2.7 m)
5'1" (1.5 m)
5'10" (1.8 m)

Distance from the lens center to
the bottom of the image [H]
38 35/64" (98 cm)
28 29/32" (73 cm)
24 3/32" (61 cm)
19 17/64" (49 cm)
14 29/64" (37 cm)
11 9/16" (29 cm)
9 41/64" (24 cm)
7 45/64" (20 cm)
6 3/4" (17 cm)
5 25/32" (15 cm)
3 55/64" (10 cm)

The formula for picture size and projection distance
[Feet/inches]
[m/cm]
L1 (ft) = 0.03843 x / 0.3048
L1 (m) = 0.03843 x
L2 (ft) = 0.0443 x / 0.3048
L2 (m) = 0.0443 x
H (in) = 0.24477 x / 2.54
H (cm) = 0.24477 x

When using a normal screen (4:3): In case of setting the 16:9 picture to the full horizontal width of the 4:3 screen.
Diag. (x)
500" (1270 cm)
400" (1016 cm)
300" (762 cm)
250" (635 cm)
200" (508 cm)
150" (381 cm)
120" (305 cm)
100" (254 cm)
80" (203 cm)
70" (178 cm)
60" (152 cm)
40" (102 cm)

Picture (Screen) size
Width
400" (1016 cm)
320" (813 cm)
240" (610 cm)
200" (508 cm)
160" (406 cm)
120" (305 cm)
96" (244 cm)
80" (203 cm)
64" (163 cm)
56" (142 cm)
48" (122 cm)
35" (81 cm)

Height
300" (762 cm)
240" (610 cm)
180" (457 cm)
150" (381 cm)
120" (305 cm)
90" (229 cm)
72" (183 cm)
60" (152 cm)
48" (122 cm)
42" (107 cm)
36" (91 cm)
24" (61 cm)

Projection distance [L]
Minimum [L1]
Maximum [L2]
47'3" (14.4 m)
—
37'10" (11.5 m)
43'7" (13.3 m)
28'4" (8.6 m)
32'8" (10.0 m)
23'8" (7.2 m)
27'3" (8.3 m)
18'11" (5.8 m)
21'10" (6.6 m)
14'2" (4.3 m)
16'4" (5.0 m)
11'4" (3.5 m)
13'1" (4.0 m)
9'5" (2.9 m)
10'11" (3.3 m)
7'7" (2.3 m)
8'9" (2.7 m)
6'7" (2.0 m)
7'8" (2.3 m)
5'8" (1.7 m)
6'6" (2.0 m)
3'9" (1.2 m)
4'4" (1.3 m)

Distance from the lens center to
the bottom of the image [H]
36 9/64" (92 cm)
28 29/32" (73 cm)
21 11/16" (55 cm)
18 1/16" (46 cm)
14 29/64" (37 cm)
10 27/32" (28 cm)
8 43/64" (22 cm)
7 15/64" (18 cm)
5 25/32" (15 cm)
5 1/16" (13 cm)
4 11/32" (11 cm)
2 57/64" (7 cm)

The formula for picture size and projection distance
[Feet/inches]
[m/cm]
L1 (ft) = 0.02882 x / 0.3048
L1 (m) = 0.02882 x
L2 (ft) = 0.03323 x / 0.3048
L2 (m) = 0.03323 x
H (in) = 0.18358 x / 2.54
H (cm) = 0.18358 x

Note
• Refer to page 15 concerning “Projection distance [L]” and “Distance from the lens center to the bottom of
the image [H]”.
• Allow a margin of error in the value in the diagrams above.
-17

XV-Z15000̲E̲US.indb 17

2008/12/25 14:25:19

Samples of Cables for Connection
• For more details of connection and cables, refer to the operation manual of the connecting equipment.
• You may need other cables or connectors not listed below.
Equipment
Video equipment

Terminal on
connected
equipment

Cable

Terminal on the
projector

HDMI output HDMI cable (commercially available)
terminal

HDMI1, 2

Component Component cable (commercially available)
video output
terminal

COMPONENT

(

3 RCA to mini D-sub 15 pin cable
(optional, AN-C3CP2)

S-video
S-video cable (commercially available)
output terminal

COMPUTER/
COMPONENT

S-VIDEO

(
Video output Video cable (commercially available)
terminal

Camera/Video game

Component
video
output
terminal

Page 19)

VIDEO

Cables for a camera or a video game/3 RCA to mini COMPUTER/
D-sub 15 pin cable (optional, AN-C3CP2)
COMPONENT

RCA adaptor plug
(commercially available)

Computer

S-video
output
terminal

Cables for a camera or a video game

S-VIDEO

Video
output
terminal

Cables for a camera or a video game

VIDEO

RGB
output
terminal

RGB cable (commercially available)

COMPUTER/
COMPONENT

(
HDMI output HDMI cable (commercially available)
terminal

Page 20)

HDMI1, 2

-18

XV-Z15000̲E̲US.indb 18

2008/12/25 14:25:20

Connecting to Video Equipment
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the devices
to be connected. After making all connections, turn on the projector and then the other devices.

Connecting Equipment with HDMI Output Terminal to the HDMI Terminal on the Projector
HDMI is a new specialized interface capable of delivering a video and audio signal to the terminal using just one cable.
Since this projector does not support an audio signal by itself, use an amplifier or other audio device.
For video connection, use a cable that conforms to HDMI standards. Using cables that do not conform to HDMI
standards may result in a malfunction.
HDMI-compatible device
To HDMI output terminal
To HDMI1 or 2 terminal

HDMI cable (type A)
(commercially available)

Connections

Note
• HDMI (High-Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition video
signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
• Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the digital
video signal does not degrade when transmitted, and a high-quality image with a simple connection can
be enjoyed.

Connecting to Equipment with S-video Output Terminal
DVD Player, etc.
To S-VIDEO terminal

To S-video output terminal

S-video cable
(commercially available)

Refer to “Samples of Cables for Connection” on page 18 for connecting other equipment.

-19

XV-Z15000̲E̲US.indb 19

2008/12/25 14:25:22

Connecting to a Computer
Ensure that the computer is the last device to be turned on after all the connections are made.

Connecting to a Computer Using the RGB Cable
Computer
To COMPUTER/COMPONENT terminal

To RGB output terminal

RGB cable
(commercially available)

Note
• Refer to “Computer Compatibility Chart” on page 57 for a list of computer signals compatible with the
projector. Use with computer signals other than those listed may cause some of the functions not to work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the computer’s external
output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook
computer). Refer to the specific instructions in your computer’s operation manual to enable your computer’s
external output port.

-20

XV-Z15000̲E̲US.indb 20

2008/12/25 14:25:22

Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control
the projector and check the status of the projector.

When connecting to a computer using an RS-232C serial control cable
Computer

To RS-232C terminal

Connections

RS-232C serial control cable (cross type, commercially available)

Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
• For details on RS-232C specifications and commands, see page 54.

Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may
damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This
may damage your computer.

-21

XV-Z15000̲E̲US.indb 21

2008/12/25 14:25:22

Turning the Projector On/Off

Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
• The power indicator illuminates red, and the
projector enters standby mode.

Turning the Projector On
Note that the connections to external equipment and
power outlet should be done before performing the
operations written below. (See pages 19 to 22.)

Power cord
(supplied)

Info
• English is the factory default language. If you
want to change the on-screen display to another
language, change the language according to the
procedure on page 44.

Open the lens shutter fully and press
STANDBY/ON on the projector or ON
on the remote control.

Power indicator
STANDBY/ON button

• The power indicator illuminates green.
• After the lamp indicator illuminates, the projector is ready to start operation.
• When the lens shutter is closed, the power
indicator blinks alternately green and orange
and the projector does not turn on.

Lamp indicator

Note
• About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green: The lamp is warming up.
Red: The lamp is shut down abnormally or the lamp should be replaced.
• When switching on the projector, a slight
flickering of the image may be experienced
within the first minute after the lamp has
been illuminated. This is normal operation as
the lamp's control circuitry is stabilising the
lamp output characteristics. It should not be
regarded as faulty operation.
• If the projector is put into standby mode and
immediately turned on again, the lamp may
take some time to start projection.

Lens shutter
STANDBY button

ON button

On-screen display

Turning the Power Off (Putting
the Projector into Standby Mode)
Press STANDBY/ON on the projector or
STANDBY on the remote control, then
press that button again while the confirmation message is displayed, to put the
projector into standby mode.
• The projector cannot be turned on while cooling.
-22

XV-Z15000̲E̲US.indb 22

Info
• Direct Power Off function:
You can unplug the power cord from the AC outlet
even if the cooling fan is still running.

2008/12/25 14:25:23

Image Projection

Adjusting the Projected
Image
Zoom ring

1 Adjusting the Focus

Focus ring

You can adjust the focus with the focus ring
on the projector.
Rotate the focus ring to adjust the
focus while watching the projected
image.

2 Adjusting the Picture Size
You can adjust the picture size using the
zoom ring on the projector.
Rotate the zoom ring to enlarge or
shrink the picture size.

3 Adjusting the Height
The height of the projector can be adjusted
using the adjustment feet.
When the screen is above the projector, the
projection image can be made higher by
adjusting the projector.

Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.

Remove your hands from the
HEIGHT ADJUST lever of the
projector after its height has
been finely adjusted.
• The angle of projection is adjustable up
to 9 degrees from the surface on which
the projector is placed.

Basic Operation

HEIGHT ADJUST lever

Make small
adjustments.

Info
Note
• When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the
procedures in Keystone Correction to correct
the distortion. (See pages 24 and 43.)

• Do not apply too much pressure on the projector
when the front adjustment feet come out.
• When lowering the projector, be careful not to get
your fingers caught in the area between the adjustment feet and the projector.
• Hold the projector firmly while lifting or carrying.
• Do not hold by the lens area.

-23

XV-Z15000̲E̲US.indb 23

2008/12/25 14:25:25

Image Projection (Continued)

Keystone Correction
This function can correct distortion of an image
projected toward a spherical or cylindrical screen
as well as trapezoidal distortion of an image on a
flat screen and rotate the image at your arbitrary
angle.

KEYSTONE button
ENTER button

■ Keystone

When the image is projected either from the top or
from the bottom towards the screen at an angle, the
image becomes distorted trapezoidally. The
function for correcting trapezoidal distortion is
called Keystone Correction.

Adjustment buttons
(P/R/O/Q)
RETURN button

Note
• The Keystone Correction can be adjusted up
to an angle of approximately ±12 degrees
with “Auto V-Keystone” and up to an angle
of approximately ±40 degrees with “V-Keystone” and approximately ±30 degrees with
“H-Keystone”.

O, Q button

For horizontal keystone correction

P, R button

For vertical keystone correction

Keystone Correction

H-Keystone Correction:

Press KEYSTONE to enter the
keystone mode.
• The keystone mode list appears.
KEYSTONE MODE
KEYSTONE

V-Keystone Correction:

SPHERE
ROTATION
SEL.

ENTER

END

Press P/R to select “KEYSTONE”,
and then press ENTER.
• The keystone menu guide appears.
KEYSTONE

H: 0

END

ADJUST

TESTPATTERN

RESET

Selectable buttons

V: 0

Note
• To return to the default setting, press RETURN
while the on-screen display of the Keystone
mode is on the screen.

Description

Info

END➞KEYSTONE Exits the keystone mode.
ADJUST➞P/R/O/Q Adjusts the keystone correction.
TESTPATTERN
➞ENTER

Displays the testpattern.

RESET➞RETURN Returns to a default setting.

Press P/R/O/Q to adjust the
Keystone Correction.

• While adjusting the image using Keystone/
Sphere/Rotation Correction, straight lines
and the edges of the image may appear
jagged.

Press KEYSTONE.
• The on-screen display of the Keystone
mode will disappear.

-24

XV-Z15000̲E̲US.indb 24

2008/12/25 14:25:28

■ Sphere

This function can correct distortion of an image
projected toward a spherical or cylindrical screen.

• The rotation menu guide appears.

Press KEYSTONE to enter the
keystone mode.

Selectable items
RETURN
ADJUST
TESTPATTERN
RESET

• The keystone mode list appears. (See
page 24.)

• The sphere menu guide appears.

P, Q button
R, O button

Description

RETURN

Returns to the keystone mode list.

ADJUST

Adjusts the sphere correction.

TESTPATTERN

Displays the testpattern.

RESET

Returns to a default setting.

Description
Returns to the keystone mode list.
Adjusts the rotation correction.
Displays the testpattern.
Returns to a default setting.

Press P/R/O/Q to adjust the
Rotation Correction mode.

Press P/R to select “SPHERE”,
and then press ENTER.
Selectable items

Press P/R to select “ROTATION”,
and then press ENTER.

Rotates the image clockwise.
Rotates the image counterclockwise.

Rotation Correction

Press P/R/O/Q to adjust the
Sphere Correction mode.
Note

P, Q button

For correction of concave distortion

R, O button

For correction of convex distortion

Sphere Correction

Correction of Concave Distortion:

• To return to the default setting, press RETURN while the
on-screen display of the Keystone mode is on the screen.

Press KEYSTONE.
• The on-screen display of the Rotation
Correction mode will disappear.

Correction of Convex Distortion:

Basic Operation

Auto V-Keystone Correction
This function can perform vertical keystone
correction automatically.

Press AUTO V-KEYSTONE on the projector to perform vertical keystone correction
which is automatically activated in response
to the installation angle of the projector.

Note
• To return to the default setting, press RETURN while
the on-screen display of the Keystone mode is on the
screen.

Press KEYSTONE.
• The on-screen display of the Sphere
Correction mode will disappear.

• The on-screen display of the Auto V-Keystone “On” appears when AUTO V-KEYSTONE is pressed once.
• Pressing AUTO V-KEYSTONE again after the on-screen
display of the Auto V-Keystone “On” has appeared
changes the on-screen display of the Auto V-Keystone
“On” to the on-screen display of the Auto V-Keystone
“Off” and the setting of the Auto V-Keystone to “0”.
• Pressing AUTO V-KEYSTONE while adjusting the image using Sphere/Rotation Correction changes Sphere/
Rotation Correction mode to Keystone mode.
AUTO V-KEYSTONE button

■ Rotation

This function rotates the image at an arbitrary angle.

Press KEYSTONE to enter the
keystone mode.
• The keystone mode list appears. (See
page 24.)
-25

XV-Z15000̲E̲US.indb 25

2008/12/25 14:25:29

Image Projection (Continued)

Switching the Input Mode
HDMI1, 2, COMPONENT,
S-VIDEO, VIDEO, COMPUTER
buttons

Select the appropriate input mode for the connected
equipment.

Press HDMI1, 2, COMPONENT,
S-VIDEO, VIDEO or COMPUTER on
the remote control to select the input
mode.

IMAGE SHIFT button
Adjustment buttons
(P/R/O/Q)

• When you press INPUT on the projector or on
the remote control, the INPUT list appears.
Press P/R to switch the INPUT mode.
INPUT list

INPUT button

INPUT
HDMI1

HDMI2
COMPONENT
COMPUTER
S-VIDEO

H-Image Shift

VIDEO

Adjusting the Vertical and
Horizontal Position of the
Image

Press P/R/O/Q to adjust the
vertical and horizontal position
of the image.

Press IMAGE SHIFT to enter the
image shift mode.
• The image shift menu guide appears.
IMAGE SHIFT
END

H: 0

V: 0

ADJUST

Selectable items

\ button

| button

H-Image Shift

Leftward

Rightward

\ button

| button

V-Image Shift
Selectable items

" button

' button

V-Image Shift

Downward

Upward

RESET

Selectable buttons

Description

END➞IMAGE SHIFT Exits the image shift mode.
ADJUST➞P/R/O/Q Adjusts the image shift.

" button

' button

RESET➞RETURN Returns to a default setting.

Note
• To return to the default setting, press
RETURN when the image shift menu guide
is still on the screen.
• Depending on the Resize mode, Picture
mode or the input signal resolution, the range
of the image shift may be limited.
-26

XVZ15000̲E̲US̲05.indd 26

2009/01/16 17:37:35

Displaying the Black Screen
Temporarily

FREEZE button
AUTO SYNC button
PICTURE MODE button

Close the lens shutter to temporarily display a black
screen.

Note
• When you close the lens shutter, the projector
will be turned off automatically after about 30
minutes.

Freezing a Moving Image

Press FREEZE.

Press FREEZE again to return to
the moving image from the currently connected device.

• The projected image is frozen.

Auto Sync function works when detecting input signal
after the projector turns on.

Press AUTO SYNC to manually adjust with
Auto Sync function.

Selecting the Picture Mode
You can select the appropriate picture mode for the
projected image, such as movie or video game.

Press PICTURE MODE.
• When pressing PICTURE MODE, the picture mode
changes in the following order:
Standard

Natural

Dynamic

Game

Movie2

Movie1

Note
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual adjustments. (See page 40.)

Basic Operation

Auto Sync
(Auto Sync Adjustment)

Note
• See page 36 for details on the picture mode.

-27

XV-Z15000̲E̲US.indb 27

2008/12/25 14:25:31

Image Projection (Continued)

MAGNIFY buttons

Displaying an Enlarged
Portion of an Image

IRIS 1, 2 buttons

Graphs, tables and other portions of projected images
can be enlarged. This is helpful when providing more
detailed explanations.

Adjustment buttons
(P/R/O/Q)
RETURN button

Press
MAGNIFY on the remote
control.

MENU HIDE button

• Enlarges the image.
• Pressing
or
MAGNIFY enlarges or
reduces the projected image.

Switching the Iris Setting

Note

Press
×1 ×2

×3

Press

×4

×9

• You can change the location of the enlarged image using P, R, O and Q.

ECO+QUIET button

Press RETURN on the remote control to cancel the operation.
• To return to the default setting (×1), press
RETURN when the on-screen display of the
magnify mode is displayed.

Note
• The selectable magnifications differ depending on the input signal.
• In the following cases, the image will return
to the normal size (×1).
- When switching the INPUT mode.
- When RETURN has been pressed while
the on-screen display of the magnify
mode is displayed.
- When the input signal is changed.
- When the input signal resolution and refresh rate (vertical frequency) change.
- When the Resize mode is changed.
- When the Picture mode is changed.

This function controls the quantity of the projected
light and the contrast of the image.
Press IRIS 1 or 2.

• Each time the button is pressed while the display is
on, the mode changes in the following order:
■ IRIS 1 High Brightness
■ IRIS 2 On

High Contrast

Off

Note
• For details, see page 37.

Hiding the Menu Temporarily
(Menu Hide)
When the menu screen is displayed, you can temporarily hide the menu screen by pressing and holding
MENU HIDE on the remote control. This is useful
when, for example, checking the video adjustment
information.

Switching the Eco+Quiet Mode
Press ECO+QUIET to switch the
Eco+Quiet mode between on and off.
• When the Eco+Quiet Mode is set to “On”, the sound of
the cooling fan will turn down, the power consumption
will decrease, and the lamp life will extend.

Note
• Refer to “Eco+Quiet” on page 37 for details.
-28

XV-Z15000̲E̲US.indb 28

2008/12/25 14:25:31

RESIZE button

Resize Mode
This function allows you to modify or customize the
resize mode to enhance the input image.

Press RESIZE on the projector or on the
remote control.
Note
• The RESIZE function that can be selected
varies depending on the input signal
(resolution and vertical frequency).

RESIZE button

Basic Operation

Resize Mode
RESIZE

Output screen image

NORMAL

The image is displayed with the original aspect ratio.

STRETCH

An image compressed from a 16:9 aspect ratio to a 4:3 aspect ratio
is restored to a 16:9 aspect ratio and displayed at full-screen.

CINEMA ZOOM

A CinemaScope image or an image with a 16:9 aspect ratio is
displayed at full-screen

-29

XV-Z15000̲E̲US.indb 29

2008/12/25 14:25:32

Image Projection (Continued)
RESIZE

Output screen image

ZOOM 14:9

An image with a 14:9 aspect ratio and letterboxing is enlarged while
maintaining the original aspect ratio.

SMART ZOOM

An image with a 4:3 aspect ratio is slightly enlarged.

DOT BY DOT

The image is displayed according to the original input signal.

About Copyrights
• When using the RESIZE function to select an image size with a different aspect ratio to a TV program or
video image, the image will look different from its original appearance. Keep this in mind while choosing an
image size.
• The use of the RESIZE or Overscan function to compress or stretch the image for commercial purposes/public
displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders.
Please use caution.

-30

XV-Z15000̲E̲US.indb 30

2008/12/25 14:25:33

Menu Bar Items
The following shows the items that can be set in the projector.
The selectable items vary depending on the selected input, input signals, or adjustment
values. Items that cannot be selected will be grayed out.
Main menu
Picture
Page 36

“Picture” menu
Picture
SIG-ADJ
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
IRIS1 (Manual)
IRIS2 (Auto)
Eco+Quiet
Advanced
Gamma
C.M.S.1
C.M.S.2
Bright Boost
Film Mode
Detail Enhance
DNR
MNR
Reset

SCR-ADJ
PRJ-ADJ
Standard
0
0
0
0
0
0
0
0
High Brightness
On
Off
0
On
Off
Off
Auto
0
Off
Off

SEL./ADJ.
RETURN

Sub menu
Picture Mode
Page 36
Contrast –30

+30

Bright

+30

–30

Color

–30

+30

Tint

–30

+30

Sharp

–30

+30

Red

–30

+30

Blue

–30

+30

CLR Temp –2

Standard
Natural
Dynamic
Movie1
Movie2
Game

Page 36
IRIS1 (Manual)
Page 37

High Brightness
High Contrast

IRIS2 (Auto)
Page 37

On
Off

Eco+Quiet
Page 37

On
Off

Advanced
Page 37

Gamma
–2
Page 37

Reset
Page 39

C.M.S.1
Page 37

Select Color
Hue

ENTER
END

Saturation
Value
Effect
C.M.S.1

“C.M.S.1” menu
C.M.S.1
Select Color
Hue
Saturation
Value
Effect
C.M.S.1
Reset
Return

Reset

On
Off

Return
C.M.S.2
Page 37

0
0
0
0

Select Color
Hue
Saturation

Value
Effect
C.M.S.2

On
Off

Useful Features

Reset
Return

SEL./ADJ.
RETURN

ENTER
END

Bright Boost
Page 39

On
Off

Film Mode
Page 39

Auto
Off

Detail
–30
Enhance

+30

Page 39
DNR
Page 39
MNR
Page 39

Off
Level 1
Level 2
Level 3

-31

XV-Z15000̲E̲US.indb 31

2008/12/25 14:25:33

Menu Bar Items (Continued)
Main menu

“SIG-ADJ” menu
Picture
SIG-ADJ
Clock
Phase
H-Pos
V-Pos
Reset
Resolution
Auto Sync
Signal Type
Video System
Video Setup
Dynamic Range

SCR-ADJ
0
0
0
0

Signal Info : 1080P
H : XX.X
kHz/
SEL./ADJ.
RETURN

PRJ-ADJ

On
Auto
Auto
0 IRE
Auto

V : XX.X
ENTER
END

SIG-ADJ
Page 40

Sub menu
Clock –150
Page 40

+150

Phase –30
Page 40

+30

H-Pos –150
Page 40

+150

V-Pos –60
Page 40

+60

Reset
Resolution
Page 40
Hz

Auto Sync
Page 40

On
Off

Signal Type
Page 40

Auto
RGB
Component

Video System
Page 41

Auto
PAL
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60

Video Setup

0 IRE
7.5 IRE

Page 41
Dynamic Range
Page 41

Auto
Standard
Enhanced

Signal Info :
Page 41

-32

XV-Z15000̲E̲US.indb 32

2008/12/25 14:25:33

Main menu

“SCR-ADJ” menu
Picture
SIG-ADJ
Resize
H-Image Shift
V-Image Shift
Overscan
Auto V-Keystone
Keystone Mode
H-Keystone
V-Keystone
Sphere
Rotation
OSD Display
OSD Brightness
Background
Menu Position
PRJ Mode
Language

SCR-ADJ
PRJ-ADJ
Normal
0
0
On

SCR-ADJ
Page 42

Keystone
0
0
0
0
On
Standard
Logo
Upper Left
Front
English

SEL./ADJ.
RETURN

Main menu
PRJ-ADJ

SCR-ADJ
On
Off
Off
Off

PRJ-ADJ

Page 45

Keystone
Sphere
Rotation

On
Off
Standard
Level 1
Level 2

Background
Page 44

Logo
Blue
None

Menu Position
Page 44

Center
Upper Right
Lower Right
Upper Left
Lower Left

PRJ Mode
Page 44

Front
Ceiling + Front
Rear
Ceiling + Rear

Language
Page 44

English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português

polski
Magyar
Türkçe

Sub menu
Auto Power Off
Page 45
Economy Mode
Page 45
One Touch Play
Page 45

Off
9600bps
Normal

On
Off

System Standby
Page 45

On
Off

Useful Features

Picture
SIG-ADJ
Auto Power Off
Economy Mode
One Touch Play
System Standby
Input Name
Demo Mode
RS-232C
Fan Mode
All Reset

Page 42
H-Image Shift –30 +30
Page 42
V-Image Shift –30 +30
Page 42
Overscan
Page 42
Auto V-Keystone
Page 43
Keystone Mode
Page 43
H-Keystone –60 +60
Page 43
V-Keystone –100 +100
Page 43
Sphere
Page 43
Rotation
Page 44
OSD Display
Page 44
OSD Brightness
Page 44

ENTER
END

“PRJ-ADJ” menu

Sub menu
Resize

On
Off
On
Off
On
Off

Input Name
Page 46

Lamp Timer (Life)
SEL./ADJ.
RETURN

X h

XX min ( XX% )
ENTER
END

Demo Mode
Page 46

On
Off

RS-232C

9600bps
38400bps
115200bps

Page 46
Fan Mode
Page 46

Normal
High

All Reset
Page 46
Lamp Timer (Life)
Page 46

-33

XV-Z15000̲E̲US.indb 33

2008/12/25 14:25:34

Using the Menu Screen

MENU button

Adjustment buttons
('/"/\/|)
Adjustment buttons
('/"/\/|)
RETURN button
ENTER button

ENTER button
RETURN button

MENU button

Menu Selections (Adjustments)
• This operation can also be performed by using
the buttons on the projector.

1
2

Press MENU.

• The “Picture” menu screen for the selected input mode is displayed.

Press | or \ to select the menu
screen to adjust on the menu
bar.

Example: “Picture” menu screen when
COMPONENT is selected for
input mode
Picture
SIG-ADJ
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
IRIS1 (Manual)
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset

SEL./ADJ.
RETURN

SCR-ADJ
PRJ-ADJ
Standard
0
0
0
0
0
0
0
0
High Brightness
On
Off

Menu bar

ENTER
END

-34

XV-Z15000̲E̲US.indb 34

2008/12/25 14:25:34

Press ' or " to select the item
you want to adjust.
(Example: Selecting “Bright”)

To adjust the projected
image while viewing it
Press ENTER.

• The selected adjustment item (e.g.
“Bright”) will be displayed at the bottom
of the screen.
• When ' or " is pressed, the next
item will be displayed. (e.g. “Bright” is
replaced with “Color” by pressing ".)

Singleadjustment
item

Picture
SIG-ADJ
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
IRIS1 (Manual)
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset

SCR-ADJ
PRJ-ADJ
Standard
0
0
0
0
0
0
0
0
High Brightness
On
Off

SEL./ADJ.
RETURN

Bright

ENTER
END

Note
• Press RETURN to return to the previous screen.

Press | or \ to adjust the item
selected.
• The adjustment is stored.
• For some menu items, press | to display its submenu and press ' or "
to select an adjustment item, and then
press ENTER.

Press MENU.

• The menu screen will disappear.

Useful Features
-35

XV-Z15000̲E̲US.indb 35

2008/12/25 14:25:34

Picture Adjustment (“Picture” Menu)
Picture
SIG-ADJ
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
IRIS1 (Manual)
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset

Menu operation ⇒ Page 34

SCR-ADJ
PRJ-ADJ
Standard
0
0
0
0
0
0
0
0
High Brightness
On
Off

IRIS2 (Auto)
Eco+Quiet
Advanced
Gamma
C.M.S.1
C.M.S.2
Bright Boost
Film Mode
Detail Enhance
DNR
MNR
Reset

0
On
Off
Off
Auto
0
Off
Off

SEL./ADJ.
RETURN
SEL./ADJ.
RETURN

ENTER
END

1 Selecting the Picture Mode
This function allows you to select the picture mode that best suits the room brightness and the type of image being
projected.
Selectable
items
Standard
Natural
Dynamic
Movie1

Description
For standard image
A balanced color image is obtained.
A vivid image is obtained.
For viewing images with the brightness
slightly toned down in a darkened
room
For viewing images with the brightness
slightly boosted in a darkened room
Use this when the audio and image
are not synched or when you want to
create a sharper image.

Movie2
Game

The main default settings of each item when selecting Picture Mode
IRIS1
CLR Temp Bright Boost
IRIS2 (Auto) Eco+Quiet
(Manual)
0
Off
High Brightness
On
Off
0
Off
High Brightness
Off
Off
0
On
High Brightness
Off
Off
-1
Off
High Contrast
Off
On

-1

Off

High Contrast

High Brightness

Off

• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are retained in memory.

Note
• You can also press PICTURE MODE on the remote control to select the picture mode. (See page 27.)
• The default settings are subject to change without notice.

2 Adjusting the Image
Adjustment items
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp

\ button
| button
For less contrast.
For more contrast.
For less brightness.
For more brightness.
For less color intensity.
For more color intensity.
For making skin tones purplish.
For making skin tones greenish.
For less sharpness.
For more sharpness.
For making images less reddish.
For making images more reddish.
For making images less bluish.
For making images more bluish.
For making images slightly more reddish For making images slightly more bluish
(slightly warmer colors).
(slightly cooler colors).

-36

XV-Z15000̲E̲US.indb 36

2008/12/25 14:25:35

Menu operation ⇒ Page 34

3 Switching the Iris Setting
This function controls the quantity of the projected light
and the contrast of the image.

■ IRIS1 (Manual)
Selectable items
High Brightness
High Contrast

Description
This mode gives priority to brightness
over contrast.
This mode gives priority to contrast
over brightness.

■ IRIS2 (Auto)
This automatically selects the optimal contrast to match
the image.
Selectable items
On
Off

Description
This mode gives priority to contrast
with the use of auto adjustment.
This mode gives priority to brightness
without the use of auto adjustment.

6 Correcting Gradation of Video (Gamma Correction)
When the darker areas of the image become difficult to
see because of the image or the projection environment,
you can correct the gamma setting to make the image
brighter and easier to see.
Selectable items
+2
+1
0
–1
–2

Provides a brighter gradation.
Standard setting
Provides a darker gradation.

7 Adjusting the Colors
You can select the color of the projected image to correct
and then adjust it to the desired color by setting “Hue”,
“Saturation”, “Value”, and “Effect”.

Note

• You can also use IRIS 1, 2 on the remote control to change the Iris. (See page 28.)

4 Eco+Quiet
Selectable items
On
Off

Description

Brightness and Power consumption
Approx. 75%
100%

Note

Select “C.M.S.1” or “C.M.S.2”
(C.M.S.: Color Management System) in the “Advanced” menu, and
press ENTER.
• If there is no data for the stored corrected
color, the color selection screen and the
picker is displayed. (Go to step 2.)

Useful Features

• When “Eco+Quiet” is set to “On”, the power
consumption will decrease and the lamp life
will extend. (Projection brightness decreases
approximately 25%.)

• Before performing this adjustment, prepare the
image to be adjusted.
• You can perform this adjustment easier in the
still image than in the moving image.

Picker

5 Using the Advanced
“Advanced” allows you to make even finer adjustments
to the image so that it appears just the way you want
it to.
To display the Advanced menu, select “Advanced” and
press ENTER.

Note
• When the “Advanced” settings are displayed,
select “Advanced” again and press ENTER to
return to the “Picture” menu.
-37

XV-Z15000̲E̲US.indb 37

2008/12/25 14:25:35

Picture Adjustment (“Picture” Menu) (Continued)
Menu operation ⇒ Page 34

• If there is data for the stored corrected
color, the C.M.S. color adjustment screen
is displayed. (Go to step 3.)
C.M.S.1
Select Color
Hue
Saturation
Value
Effect
C.M.S.1
Reset
Return

Set or adjust each item in the C.M.S.
color adjustment screen.
C.M.S.1
Select Color
Hue
Saturation
Value
Effect
C.M.S.1
Reset
Return

0
0
0
0

SEL./ADJ.
RETURN
SEL./ADJ.
RETURN

0
0
0
0

ENTER
END

C.M.S. color adjustment screen:
Selectable items

Use the picker and select the color
of the projected image to correct.
The picker can be operated by adjustment buttons (P/R/O/Q) on the
remote control.
• By enlarging the projected image using
or
MAGNIFY, more fine adjustment can
be performed.

Description

Select Color

Starts over the selection of the
color to be corrected.

Hue

Sets the hue of the main colors.

Saturation

Sets the saturation of the main
colors.

Value

Sets the value of the main colors.

Effect*1

Specifies the range of color correction.

C.M.S.1*2
(or C.M.S.2)

Checks the appearance of the
projected image after above
correction.

Reset

Sets “Hue”, “Saturation”, “Value”,
and “Effect” to their default values.

Return

Completes the correction and closes
the C.M.S. color adjustment screen.

Picker

*1 To specify the range of color correction, select
“Effect” and press O or Q button.
O button

Specifies smaller range.

Q button

Specifies larger range.

*2 To check the appearance of the projected image,
select “C.M.S.1” (or “C.M.S.2”) and set to “On”
or “Off”.

• By continuing to press the adjustment
buttons (P/R/O/Q), the picker moves
rapidly.
After selecting the color of the projected
image to correct, press ENTER. The
C.M.S. color adjustment screen is
displayed. (Go to step 3.)

The appearance of the projected
image after above color adjustment
reflected can be checked.

Off

The appearance of the projected
image in former color adjustment
can be checked.

To complete the C.M.S. color
adjustment, select “Return” and
press ENTER.

Note
• The C.M.S. color adjustment can be made to
one color each in “C.M.S.1” and “C.M.S.2”.
-38

XV-Z15000̲E̲US.indb 38

2008/12/25 14:25:37

Menu operation ⇒ Page 34

8 Adjusting the Bright Boost
Bright Boost uses Texas Instruments’ Bright Boost
technology. The image becomes brighter while the color
reproduction is kept at a high level.
Selectable items
On

Description
The Bright Boost function is activated.

Off

The Bright Boost function is not activated.

w Mosquito Noise Reduction (MNR)
The so-called Mosquito Noise (flickering) can be
reduced.
Selectable items
Off
Level 1
Level 2
Level 3

Description
MNR does not function.
Sets the MNR level for viewing a clearer picture.

9 Selecting the Film Mode
This function provides high-quality playback of
images originally projected at 24 fps, such as movies
on DVDs.
Selectable items
Auto
Off

Description
Films are detected automatically.
Films are not detected.

0 Setting Detail Enhancement
This function enhances the details in images and,
thereby, creates a greater sense of depth.
\ button

Provides less detail enhancement.

| button

Provides more detail enhancement.

Note
Set “MNR” to “Off” in the following cases:
• When the image is blurry.
• When the contours and colors of moving images
drag.
• When TV broadcasts with weak signals are projected.
• This function can be set when the input signal
is 480I/480P, 576I/576P, S-VIDEO or VIDEO.

e Resetting All Adjustment Items
To reset all adjustment items to the default settings,
select “Reset” and press ENTER.

ｑ Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides high quality
images with minimal dot crawl and cross color noise.
Selectable items
Off
Level 1
Level 2
Level 3

Description
The DNR function is not activated.
Sets the DNR level for viewing a clearer picture.

Useful Features

Note
Set “DNR” to “Off” in the following cases:
• When the image is blurry.
• When the contours and colors of moving images
drag.
• When TV broadcasts with weak signals are projected.
• This function can be set when the input signal
is 480I/480P, 576I/576P, S-VIDEO or VIDEO.

-39

XV-Z15000̲E̲US.indb 39

2008/12/25 14:25:37

Computer Image Adjustment (“SIG-ADJ” Menu)
Menu operation ⇒ Page 34

The illustration shown here is for explanation and may
be different from the actual on-screen display.

Picture
SIG-ADJ
Clock
Phase
H-Pos
V-Pos
Reset
Resolution
Auto Sync
Signal Type
Video System
Video Setup
Dynamic Range

SCR-ADJ
0
0
0
0

Signal Info : 1080P
H : XX.X
kHz/
SEL./ADJ.
RETURN

PRJ-ADJ

On
Auto
Auto
0 IRE
Auto

V : XX.X

1 Adjusting the Computer Image

V-Pos

Selectable items
On

ENTER
END

Use the SIG-ADJ function in case of irregularities such as
vertical stripes or flickering in portions of the screen.

H-Pos

• Avoid displaying computer patterns which repeat
every other line (horizontal stripes). (Flickering
may occur, making the image hard to see.)
• Information on the currently selected input
signal can be confirmed in item 8 on page 41.

3 Auto Sync (Auto Sync Adjustment)

*1 If the input mode is S-VIDEO or VIDEO input, the display
changes to the “Video System” screen.
*2 Displayed when the input mode is HDMI input.

Selectable items
Clock
Phase

Note

Description
Adjusts vertical noise.
Adjusts horizontal noise (similar to
tracking on your VCR).
Centers the on-screen image by
moving it to the left or right.
Centers the on-screen image by
moving it up or down.

Note
• You can automatically adjust the computer
image by setting “Auto Sync” in the “SIG-ADJ”
menu to “On”, or pressing AUTO SYNC on the
remote control.
• Depending on the type of input signal, the
adjustment range for each setting may vary or
the adjustment may not be available at all.
• To reset all adjustment items, select “Reset”
and press ENTER.

2 Setting the Resolution
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in
“Resolution” in the “SIG-ADJ” menu may need to be
selected to match the computer display mode.

Off

Description
Auto Sync adjustment will occur when
the projector is turned on or when
the input signals are switched, when
connected to a computer.
Auto Sync adjustment is not
automatically performed.

Note
• Auto Sync adjustment is also performed by
pressing AUTO SYNC on the remote control.
• When setting “Auto Sync” to “Off”, and if
AUTO SYNC is pressed, Auto Sync will be executed in “On” mode. If the button is pressed
again within one minute, Auto Sync will be
executed in “On” mode.
• The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
• When the optimum image cannot be achieved with
Auto Sync adjustment, use manual adjustments.

4 Signal Type Setting
When using an input mode of HDMI1, HDMI2, or COMPUTER, set the signal type to the corresponding input
signal type (RGB or Component).
Selectable items
Auto

RGB
Component

Description
Automatically selects the appropriate
input signal between RGB and Component.
Set when RGB signals are received.
Set when component signals are received.

-40

XV-Z15000̲E̲US.indb 40

2008/12/25 14:25:38

Menu operation ⇒ Page 34

5 Setting the Video System
The video input system mode is factory preset to “Auto”;
however, a clear picture from the connected audio-visual
equipment may not be received, depending on the video
signal difference. In that case, switch the video signal.
Selectable items
Auto
PAL
SECAM
*NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60

* When reproducing NTSC signals in PAL video equipment.

7 Adjusting the Dynamic Range
An optimum picture may not be displayed if an HDMIcapable device’s output signal type and the projector’s
input signal type do not match. If this should occur,
switch “Dynamic Range”.
Selectable items
Auto

Description
In most circumstances, “Auto” should
be selected.

Standard
Enhanced

When the black levels of the image
show banding or appear faded, select
the item that results in the best picture
quality.

8 Signal Info
Input signal information is displayed.

Note
• The video signal can only be set in VIDEO or
S-VIDEO mode.
• When “Video System” is set to “Auto”, you
may not receive a clear picture due to signal
differences. Should this occur, switch to the
video system of the source signal.

6 Setting the Video Setup
Selectable items
0 IRE
7.5 IRE

Description
Sets the black level to 0 IRE.
Sets the black level to 7.5 IRE.

Note

Useful Features

• This can be used for a 480I signal connected to
the COMPONENT terminal or the COMPUTER/
COMPONENT terminal.
• This can be used for an NTSC3.58 signal connected to the VIDEO or S-VIDEO terminal.

-41

XV-Z15000̲E̲US.indb 41

2008/12/25 14:25:38

Adjusting the Projected Image (“SCR-ADJ” Menu)
Menu operation ⇒ Page 34

The illustration shown here is for explanation and may
be different from the actual on-screen display.
Picture
SIG-ADJ
Resize
H-Image Shift
V-Image Shift
Overscan
Auto V-Keystone
Keystone Mode
H-Keystone
V-Keystone
Sphere
Rotation
OSD Display
OSD Brightness
Background
Menu Position
PRJ Mode
Language

SCR-ADJ
PRJ-ADJ
Normal
0
0
On

■ V-Image Shift
Selectable items
V-Image Shift

\ button

ENTER
END

Note

Note
• For details of the Resize mode, see page 29.
• You can also press RESIZE on the remote
control to set the resize mode. (See page 29.)

• Depending on the Resize mode, Picture mode
or the input signal resolution, the range of the
image shift may be limited.

3 Adjusting the Overscan
This function allows you to adjust the Overscan area
(display area).
Selectable items

2 Adjusting the Image Position
You can move the projected image horizontally or vertically.

■ H-Image Shift

\ button

| button

On
Standard
Logo
Upper Left
Front
English

1 Setting the Resize Mode

H-Image Shift

| button
Upward

Keystone
0
0
0
0

SEL./ADJ.
RETURN

Selectable items

\ button
Downward

On
Off

Description
The input area is displayed without screen
edges.
The whole input area is displayed.

Note
\ button
Leftward

| button
Rightward

| button

• You can adjust the Overscan area for the following input signals and the RESIZE function.
- Input signal: 480I/480P, 540P, 576I/576P,
720P, 1035I or 1080I/1080P
- RESIZE function:“NORMAL”, “STRETCH”,
“CINEMA ZOOM” or “ZOOM 14:9”
• If the display area ratio is set too large, noise
may appear at the screen edges. If this happens, set the display area ratio to a smaller
value.
• Also read “About Copyrights” on page 30.

-42

XVZ15000̲E̲US̲07.indd 42

2009/01/16 17:38:15

Menu operation ⇒ Page 34

4 Auto V-Keystone Correction
Select “Auto V-Keystone” in the “SCR-ADJ” menu and
press ENTER. Vertical keystone correction is performed
automatically.

Select “Keystone Mode” in the “SCR-ADJ” menu
and press ENTER. Then select a desired item among
“Keystone”, “Sphere”, or “Rotation” and press ENTER.
“Keystone” has been set as a default setting in which
you can adjust “H-Keystone” and “V-Keystone”.

■ Keystone
Note
• Pressing ENTER when the on-screen display
of the Auto V-Keystone “On” appears changes
the setting of the Auto V-Keystone to “Off”.
• For details of Keystone mode, see page 24.
• Pressing AUTO V-KEYSTONE while adjusting
the image using Sphere/Rotation Correction
changes Sphere/Rotation Correction mode to
keystone mode.
Auto V-Keystone Correction

H-Keystone:

O or Q

Makes the upper and lower
sides parallel.

Horizontal Keystone Correction

V-Keystone:

O or Q

Makes the left and right sides
parallel.

Vertical Keystone Correction

5 Keystone Mode Correction
This function can correct distortion of an image projected
toward a spherical or cylindrical screen as well as trapezoidal distortion of an image on a flat screen and rotate
the image at your arbitrary angle.

Note
• For details of Keystone mode, see page 24.

■ Sphere
This function corrects screen distortion created during
spherical or cylindrical screen projection.

O button

Narrower at the center

Q button

Wider at the center

Sphere Correction

Correction of Convex Distortion:

Useful Features

Info
• While adjusting the image using Keystone/
Sphere/Rotation Correction, straight lines
and the edges of the image may appear
jagged.

Correction of Concave Distortion:

-43

XV-Z15000̲E̲US.indb 43

2008/12/25 14:25:39

Adjusting the Projected Image (“SCR-ADJ” Menu) (Continued)
Menu operation ⇒ Page 34

■ Rotation
This function can rotate the image at an arbitrary
angle.

O button

Rotates the image
counterclockwise.

Q button

Rotate the image clockwise.

Rotation Correction

0 Reversing/Inverting
Projected Images
This function allows the projector to be used in a wider
range of projection styles by allowing the image to be
inverted to suit the projection environment (location).
Selectable items
Front
Ceiling + Front

Rear

6 Setting On-screen Display
Selectable items
On
Off

Description
All on-screen displays are displayed.
INPUT/FREEZE/AUTO SYNC/RESIZE/
PICTURE MODE/ECO+QUIET/
MAGNIFY/ “An invalid button has been
pressed.” are not displayed.

7 Setting the Brightness of the
Menu Screen
Sets the brightness of the menu screen.
Selectable items
Standard
Level 1
Level 2

Description
Standard brightness
Darker than the “Standard”
brightness
Darker than the “Level 1” brightness

8 Selecting the Background Image
Selectable items
Logo
Blue
None

Description
SHARP logo screen
Blue screen
— (Black screen)

Ceiling + Rear

Description
Normal image (Projected from the
front of the screen)
Inverted image (Projected from the
front of the screen with an inverted
projector)
Reversed image (Projected from the
rear of the screen or with a mirror)
Reversed and inverted image (Projected with a mirror)

See page 16 for details of Projection (PRJ) Mode.

q Selecting the On-screen Display
Language
The projector can switch the on-screen display language
among 17 languages.

English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
polski
Magyar
Türkçe

9 Selecting the Menu Screen
Position
Select “Menu Position” in the “SCR-ADJ” menu and the
desired position for the menu screen.
Selectable items
Center
Upper Right
Lower Right
Upper Left
Lower Left

Description
Displayed on the center of the image.
Displayed on the upper right of the image.
Displayed on the lower right of the image.
Displayed on the upper left of the image.
Displayed on the lower left of the image.

-44

XV-Z15000̲E̲US.indb 44

2008/12/25 14:25:40

Adjusting the Projector Function (“PRJ-ADJ” Menu)
Menu operation ⇒ Page 34

The illustration shown here is for explanation and may
be different from the actual on-screen display.
Picture
SIG-ADJ
Auto Power Off
Economy Mode
One Touch Play
System Standby
Input Name
Demo Mode
RS-232C
Fan Mode
All Reset

SCR-ADJ
On
Off
Off
Off

3 Setting One Touch Play, System
Standby and Input Name

PRJ-ADJ

Off
9600bps
Normal

When a Sharp product equipped with Consumer Electronics Control (HDMI CEC) is connected to the projector
with an HDMI cable, you can use the linked function with
HDMI CEC (“One Touch Play” and “System Standby”).

Note
The CEC function may not work with some CEC
devices. (When the projector is connected to a nonSharp product, the CEC function may not work.)

Lamp Timer (Life)
SEL./ADJ.
RETURN

X h

XX min ( XX% )
ENTER
END

1 Setting Auto Power Off Mode
This function automatically switches the projector to
Standby mode if no signals are received for a set period.
Selectable items
On

Off

Description
When no input signal is detected for
more than 15 minutes, the projector
will automatically enter standby mode.
The Auto Power Off function will be
disabled.

Note
• When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.

■ Economy Mode
Selectable items
On
Off

Description
This enables the Economy mode.
You can use the linked functions. RS232C can be used to control the projector in standby mode.

Note
• Set this function to “Off” when you want to use
RS-232C to control the projector from a computer.
• One Touch Play is set to “Off” when the
Economy mode is set to “On”.

One Touch Play turns on the projector and selects the
input automatically when you turn on or begin playback
on connected HDMI-compliant Sharp Video Products.
Selectable items
On
Off

Description
This enables One Touch Play.
This disables One Touch Play.

Note
• When enabling One Touch Play, be sure to enable
the CEC setting on the HDMI-compliant Sharp
Video Products connected to the projector.
• The Economy mode is set to “Off” when One
Touch Play is set to “On”.
• In the following cases, One Touch Play is not
enabled.
- When playback is paused
- When the screen is turned off (black) after the
lens shutter is closed
- When the cooling fan is running (See page
48.)
- When the lamp is warming up (See page 48.)

■ Setting the System Standby Function
(System Standby)
When you turn off the projector, the HDMI-compliant
video equipment connected to the projector enters
standby mode.
Selectable items
On
Off

Description
This enables System Standby.
This disables System Standby.

Useful Features

2 Setting the Power Save Mode
(Economy Mode)

■ Setting the One-Touch Playback Function
(One Touch Play)

Note
• When enabling System Standby, be sure to
enable the CEC setting on the HDMI-compliant
Sharp Video Products connected to the
projector.
-45

XVZ15000̲E̲US̲07.indd 45

2009/01/14 15:42:43

Adjusting the Projector Function (“PRJ-ADJ” Menu) (Continued)
Menu operation ⇒ Page 34

■ Setting the Input Terminal Names (Input
Name)
Set the name of the input terminal (up to 14 alphanumerical characters).

Press P/R to select “Input Name”
and then press ENTER.
Picture
Input name

SIG-ADJ
HDMI1

SCR-ADJ

PRJ-ADJ

HDMI1

5 Selecting the Transmission
Speed (RS-232C)
Make sure that both the projector and computer are set
for the same baud rate.
Selectable items
9600bps

Description
Transmission speed is slow.

38400bps
115200bps

Transmission speed is rapid.

Reset
Return

6 Fan Mode Setting
This function changes the fan rotation speed.

\ or | button

Selects a character column.

▼ or 、 button

Selects a character.

ENTER button

Sets the input terminal name.

Press P/R to select “Return” and
then press ENTER to return to the
previous screen.
• To return to the previous setting, select
“Reset” and then press ENTER.

Selectable items
Normal
High

Description
Suitable for normal environments.
Select this when using the projector at
altitudes of approximately 4,900 feet
(1,500 meters) or more.

• When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.

7 Returning to the Default Settings
Use “All Reset” to initialize all the adjustments you have
made to the default settings.

Note
• When connecting the projector to a Sharp Video
Product with an HDMI cable using an input
mode of HDMI1 or HDMI2 and the linked function with HDMI CEC (“One Touch Play” or “System Standby”) works normally, the name of the
connected Sharp Video Product is automatically
captured.
• When the input terminal name has been changed
by a user, the changed name is displayed.
• To return to the default name, select “Reset”
and press ENTER.

4 Setting the Demo Mode
Set the Demo Mode to “On” or “Off”.
Selectable items
On
Off

Description
This enables Demo Mode.
This disables Demo Mode.

Note
The following items cannot be initialized.
• “SIG-ADJ” menu — Resolution
• “SCR-ADJ” menu — Language
• “PRJ-ADJ” menu — Lamp Timer (Life)

8 Lamp Timer (Life)
You can confirm the cumulative lamp usage time and the
remaining lamp life (percentage).
Lamp usage condition
“Life”

Remaining lamp life
100%

Operated exclusively with
“Eco+Quiet” set to “On”

Approx. 3,000
hours

Approx. 150
hours

Operated exclusively with
“Eco+Quiet” set to “Off”

Approx. 2,000
hours

Approx. 100
hours

Note
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
• The lamp life may vary depending on the usage condition.

-46

XVZ15000̲E̲US̲07.indd 46

2009/01/14 15:42:44

Maintenance
Cleaning the projector

Cleaning the lens

■ Ensure that you have unplugged the power cord
before cleaning the projector.
■ The cabinet as well as the operation panel is made
of plastic. Avoid using benzene or thinner, as these
can damage the finish on the cabinet.
■ Do not use volatile agents such as insecticides on
the projector.
■ Do not attach rubber or plastic items to the projector for long periods.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the
projector.
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in a
mild detergent diluted with water, wring the cloth
well and then wipe the projector.
Strong cleaning detergents may discolor, warp or
damage the coating on the projector. Make sure to
test on a small, inconspicuous area on the projector before use.

■ Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the coating
film on the surface of the lens.
■ As the surface of the lens can easily get damaged,
be careful not to scrape or hit the lens.

Cleaning the exhaust and intake vents

■ Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
nt
ge
ter

Mild detergent diluted
with water

Info
Wax

Thinner

• If you want to clean the air vents during projector
operation, ensure you press STANDBY/ON on
the projector or STANDBY on the remote control
and put the projector into standby mode. After
the cooling fan has stopped, clean the vents.

Appendix
-47

XV-Z15000̲E̲US.indb 47

2008/12/25 14:25:42

Maintenance Indicators
■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector
indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and
the projector will enter standby mode. After the projector has entered standby mode, follow the procedures
given below.
Top View

Power indicator
Lamp indicator
Temperature warning
indicator

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting
location, the temperature warning indicator will blink. And if the temperature keeps on rising,
“
” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking.
If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter
standby mode. When you find the temperature warning indicator blinking, be sure to perform the measures
described on page 49.

About the lamp indicator

■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on
the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off
and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate
in red.
■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will not
turn on.
Indicators on the Projector
Power indicator

Lamp indicator

Temperature warning
indicator

Red on
Green on
Red blinks
Green blinks
Green and orange blink
alternately
Green on
Green blinks
Red on
Off
Red on/Red blinks

Normal (Standby)
Normal (Power on)
Abnormal (See page 49.)
Normal (Cooling)
The lens shutter is closed. (See page 22.)
Normal
The lamp is warming up.
The lamp is shut down abnormally or requires to be changed. (See
page 49.)
Normal
The internal temperature is abnormally high. (See page 49.)

-48

XV-Z15000̲E̲US.indb 48

2008/12/25 14:25:43

Maintenance indicator
Normal
Abnormal
Temperature
Off
Red blinks
warning
(On)/
indicator
Red on
(Standby)

Lamp
indicator

Green on
(Green
blinks when
the lamp is
warming up.)

Red on

Red on
(Standby)

Power
indicator

Green on/
Red on
Green blinks
(Cooling)

Red blinks

Problem

Cause

The internal
temperature is
abnormally
high.

• Temperatures
around the
projector are
high.
• Blocked air
intake
• Cooling fan
breakdown
• Internal circuit
failure
• Clogged air
intake
The lamp does • The lamp is shut
not illuminate.
down
abnormally.
Time to change • Remaining lamp
the lamp.
life becomes 5%
or less.
The lamp does • Burnt-out lamp
not illuminate.
• Lamp circuit
failure

The power
• The lamp unit
indicator blinks
cover is open.
in red when the
projector is on.

Possible Solution
• Use the projector in an area with a
temperature of lower than 95°F (+35ºC).
• Relocate the projector to an area with
proper ventilation. (See page 6.)

• Take the projector to your nearest Sharp
Authorized Projector Dealer or Service
Center (see page 60) for repair.

• Disconnect the power cord from the AC
outlet, and then connect it again.
• Carefully replace the lamp. (See page
50.)
• Take the projector to your nearest Sharp
Authorized Projector Dealer or Service
Center (see page 60) for repair.
• Please exercise care when replacing the
lamp.
• Securely install the cover.
• If the power indicator blinks in red even
when the lamp unit cover are securely
installed, contact your nearest Sharp
Authorized Projector Dealer or Service
Center (see page 60) for advice.

Info
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plugging in the
power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red
and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power
cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is controlled
automatically. The sound of the cooling fan may change during operation because the fan speed may
change and this is not a malfunction.

Appendix
-49

XV-Z15000̲E̲US.indb 49

2008/12/25 14:25:44

Regarding the Lamp
Lamp

■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp
life (percentage) can be checked with the on-screen display. (See page 46.)
■ Purchase a replacement lamp of type AN-K15LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service
of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer
or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
www.lamprecycle.org or 1-800-BE-SHARP

U.S.A. ONLY

Caution Concerning the Lamp

■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
■ The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer
or Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of
exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns
or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section. * If you wish, you
may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector
Dealer or Service Center for repair.

-50

XV-Z15000̲E̲US.indb 50

2008/12/25 14:25:44

Removing and Installing the Lamp Unit
Warning!

• Do not remove the lamp unit from the projector right after use. The lamp and parts
around the lamp will be very hot and may cause burns or injury.

Info
• Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to
the lamp, make sure you carefully follow
the steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.

Press STANDBY/ON on the
projector or STANDBY on the
remote control to put the projector into standby mode.

Disconnect the power cord.

Remove the lamp unit cover.

Lamp unit
AN-K15LP

Optional
accessory

STANDBY/ON button

AC socket

• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).

• Close the lens shutter. Loosen the user
service screw (1) that secures the lamp
unit cover. Remove the lamp unit cover
(2).

Appendix

User service screw
(for lamp unit cover)

-51

XV-Z15000̲E̲US.indb 51

2008/12/25 14:25:45

Regarding the Lamp (Continued)
4

Remove the lamp unit.

Insert the new lamp unit.

Replace the lamp unit cover.

Securing screws

• Loosen the securing screws from the
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.

• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.

• Align the tab on the lamp unit cover
(1) and place it while pressing the cover
(2) to close it. Then tighten the user
service screw (3) to secure the lamp
unit cover.

Info
• If the lamp unit and lamp unit cover are
not correctly installed, the power will
not turn on, even if the power cord is
connected to the projector.

2
3

Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.

Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this
may cause the lamp to become damaged
or explode.

Connect the power cord and
open the lens shutter fully.

• Plug the power cord into the AC socket
of the projector.

Reset the lamp timer.

AC socket

Lamp indicator
STANDBY/
ON button
ENTER
button
R button
MENU button

• While simultaneously holding down
MENU, ENTER and R on the projector,
press STANDBY/ON on the projector and
keep all four buttons pressed down until
the lamp indicator starts blinking green.
• “LAMP 0000 H” is displayed, indicating
that the lamp timer is reset.

-52

XV-Z15000̲E̲US.indb 52

2008/12/25 14:25:46

Connecting Pin Assignments
COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals :
mini D-sub 15 pin female connector
11

1
6

5
10

COMPUTER Input/Output

COMPONENT Input/Output

Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

Signal
Video input (red)
Video input (green/sync on green)
Video input (blue)
Not connected
Not connected
Earth (red)
Earth (green/sync on green)
Earth (blue)
Not connected
GND
Not connected
Bi-directional data
Horizontal sync signal: TTL level
Vertical sync signal: TTL level
Data clock

Signal
PR (CR)
Y
PB (CB)
Not connected
Not connected
Earth (PR)
Earth (Y)
Earth (PB)
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected

RS-232C Terminal: 9-pin D-sub male connector
Pin No.
1
2
3
4
5
6
7
8
9

9876

54321

Signal
RD
SD
SG

Name
Receive Data
Send Data
Reserved
Signal Ground
Reserved
Reserved
Reserved

I/O
Input
Output

Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected

HDMI Terminal
18

Pin No.
1
2
3
4
5
6
7

Name
Pin No.
T.M.D.S data 2+
8
T.M.D.S data 2 shield
9
T.M.D.S data 2–
10
T.M.D.S data 1+
11
T.M.D.S data 1 shield
12
T.M.D.S data 1–
13
T.M.D.S data 0+

Name
Pin No.
T.M.D.S data 0 shield
14
T.M.D.S data 0–
15
T.M.D.S clock+
16
T.M.D.S clock shield
17
T.M.D.S clock–
18
CEC
19

Name
Reserved
SCL
SDA
DDC/CEC ground
+5V power
Hot plug detection

Appendix
-53

XV-Z15000̲E̲US.indb 53

2008/12/25 14:25:48

RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 21 for connection.)

Communication conditions
Set the serial port settings of the computer as follows.
Signal format: Conforms to RS-232C standard.
Baud rate*: 9,600 bps / 38,400bps / 115,200bps
Data length: 8 bits
*Use the same settings for the projector and computer.

Parity bit: None
Stop bit: 1 bit
Flow control: None

Basic format
Send commands from the computer in the following order: command, parameter, and return code. After
processing the command from the computer, the projector sends a response code to the computer.
Command format

C3 C4

Command 4-digit
Response code format
Normal response

Return code (0DH)

Parameter 4-digit
Problem response (communication error or incorrect command)

Return code (0DH)

Info
• If you are controlling the projector from a computer using RS-232C commands, wait at least 30 seconds
after turning the projector on before sending any commands.
• When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified.
• When using the computer control function of the projector, the projector’s operating status cannot be read
by the computer. Therefore, confirm the status by transmitting the display commands for each adjustment
menu and checking the status with the on-screen display. If the projector receives a command other than a
menu display command, it will execute the command without displaying the on-screen display.

Commands
Example: To turn on the projector
Computer

Projector

→
←

K
Return

Control Contents
Power

Name

Parameter

Standby mode
(or 30-second startup time)

Power ON

Off

OK or ERR

Status

0:Normal
1:Temp High
8:Lamp Life 5% or less
16:Lamp Burnt-out
32:Lamp Ignition Failure

0:Normal
1:Temp High
2:Fan Error
4:Lamp Cover Open
8:Lamp Life 5% or less
16:Lamp Burnt-out
32:Lamp Ignition Failure
64:Temp Abnormally High

Projector Condition

Lamp

Command

OK or ERR

Status

0:Off, 1:On, 2:Retry
3:Waiting, 4:Lamp Error

0:Off, 4:Lamp Error

Power Status

1:On, 2:Cooling

0:Standby

Quantity

Usage Time (Hour)

0-9999 (Integer)

Usage Time (Minuite)

0, 15, 30, 45

Life (Percentage)

0%-100% (Integer)

Model Name Check

XVZ15000

Model Name Check

XV-Z15000

Projector Name Setting1 (First 4 characters) *1

OK or ERR

Projector Name Setting2 (Middle 4 characters) *1

Projector Name Setting3 (Last 4 characters) *1

OK or ERR

Projector Name Check

Projector Name

OK or ERR

-54

XV-Z15000̲E̲US.indb 54

2008/12/25 14:25:49

Return
Control Contents
Input Change

Command

Parameter

Standby mode
(or 30-second startup time)

Power ON

Computer

OK or ERR

ERR

Component

OK or ERR

ERR

HDMI1

OK or ERR

ERR

HDMI2

OK or ERR

ERR

S-Video

OK or ERR

Video

OK or ERR

ERR

Input RGB Check

1: Computer, 2: Component,

ERR

Input Video Check

1: S-Video, 2: Video, ERR

Input Mode Check

1: RGB, 2: Video

ERR

Input Check

1: Computer
2: Component
3: HDMI1
4: HDMI2
5: S-Video
6: Video

ERR

3: HDMI1, 4: HDMI2, ERR

Resize

Computer

Component

Normal

OK or ERR

ERR

Stretch

OK or ERR

ERR

Dot By Dot

OK or ERR

ERR

Cinema Zoom

OK or ERR

ERR

Zoom14:9

OK or ERR

ERR

Smart Zoom

OK or ERR

ERR

Normal

OK or ERR

ERR

Stretch

OK or ERR

ERR

Dot By Dot

HDMI1

Video

Picture Mode

OK or ERR

ERR

OK or ERR

ERR

OK or ERR

ERR

Smart Zoom

OK or ERR

ERR

Normal

OK or ERR

ERR

Stretch

OK or ERR

ERR

OK or ERR

ERR

Cinema Zoom

OK or ERR

ERR

Zoom14:9

OK or ERR

ERR

Smart Zoom

OK or ERR

ERR

Normal

OK or ERR

ERR

Stretch

OK or ERR

ERR

OK or ERR

ERR

Cinema Zoom

OK or ERR

ERR

Zoom14:9

OK or ERR

ERR

Smart Zoom

OK or ERR

ERR

Normal

OK or ERR

ERR

Stretch

OK or ERR

ERR

Cinema Zoom

OK or ERR

ERR

Zoom14:9

OK or ERR

ERR

Smart Zoom

OK or ERR

ERR

Normal

OK or ERR

ERR

Stretch

OK or ERR

ERR

Cinema Zoom

OK or ERR

ERR

Zoom14:9

OK or ERR

ERR

Smart Zoom

OK or ERR

ERR

OK or ERR

Standard

OK or ERR

ERR

Natural

OK or ERR

ERR

Dynamic

OK or ERR

ERR

Movie1

OK or ERR

ERR

Movie2

OK or ERR

ERR
ERR

ERR

Game

OK or ERR

Contrast

-30 - +30

OK or ERR

ERR

Bright

-30 - +30

OK or ERR

ERR

Color

-30 - +30

OK or ERR

ERR

Tint

-30 - +30

OK or ERR

ERR

Sharp

-30 - +30

OK or ERR

ERR

Red

-30 - +30

OK or ERR

ERR

Blue

-30 - +30

OK or ERR

ERR

CLR Temp

-2-+2

OK or ERR

ERR

OK or ERR

ERR

Standard

OK or ERR

ERR

Natural

OK or ERR

ERR

Dynamic

OK or ERR

ERR

Movie1

OK or ERR

Movie2

OK or ERR

ERR

Game

OK or ERR

ERR

Picture Reset
Component INPUT

ALL Reset
Computer INPUT

Zoom14:9

Dot By Dot

S-Video

Cinema Zoom

Dot By Dot

HDMI2

ERR

Picture Mode

ERR

-30 - +30

OK or ERR

ERR

-30 - +30

OK or ERR

ERR

Color

-30 - +30

OK or ERR

ERR

Tint

-30 - +30

OK or ERR

ERR

Sharp

-30 - +30

OK or ERR

ERR

Red

-30 - +30

OK or ERR

ERR

Blue

-30 - +30

OK or ERR

ERR

CLR Temp

-2-+2

OK or ERR

ERR

OK or ERR

ERR

Picture Reset

Appendix

Contrast
Bright

-55

XV-Z15000̲E̲US.indb 55

2008/12/25 14:25:50

RS-232C Specifications and Commands (Continued)
Return
Control Contents
HDMI1

Picture Mode

Command
R

OK or ERR

ERR

Natural

OK or ERR

ERR

Dynamic

OK or ERR

ERR

Movie1

OK or ERR

ERR

Movie2

OK or ERR

ERR
ERR

Game

OK or ERR

Contrast

-30 - +30

OK or ERR

ERR

Bright

-30 - +30

OK or ERR

ERR

Color

-30 - +30

OK or ERR

ERR

Tint

-30 - +30

OK or ERR

ERR

Sharp

-30 - +30

OK or ERR

ERR

Red

-30 - +30

OK or ERR

ERR

Blue

-30 - +30

OK or ERR

ERR

CLR Temp

-2-+2

OK or ERR

ERR

OK or ERR

ERR

Standard

OK or ERR

ERR

Natural

OK or ERR

ERR

Dynamic

OK or ERR

ERR
ERR

Picture Mode

Movie1

OK or ERR

Movie2

OK or ERR

ERR

Game

OK or ERR

ERR

Contrast

-30 - +30

OK or ERR

ERR

Bright

-30 - +30

OK or ERR

ERR

Color

-30 - +30

OK or ERR

ERR

Tint

-30 - +30

OK or ERR

ERR

Sharp

-30 - +30

OK or ERR

ERR

Red

-30 - +30

OK or ERR

ERR

Blue

-30 - +30

OK or ERR

ERR

CLR Temp

-2-+2

OK or ERR

ERR

OK or ERR

ERR

Picture Reset
S-Video INPUT

Picture Mode

Contrast

Standard

OK or ERR

ERR

Natural

OK or ERR

ERR

Dynamic

OK or ERR

ERR

Movie1

OK or ERR

ERR

Movie2

OK or ERR

ERR

Game

OK or ERR

ERR

-30 - +30

OK or ERR

ERR
ERR

Bright

-30 - +30

OK or ERR

Color

-30 - +30

OK or ERR

ERR

Tint

-30 - +30

OK or ERR

ERR

Sharp

-30 - +30

OK or ERR

ERR

Red

-30 - +30

OK or ERR

ERR

Blue

-30 - +30

OK or ERR

ERR

CLR Temp

-2-+2

OK or ERR

ERR

OK or ERR

ERR

Standard

OK or ERR

ERR

Natural

OK or ERR

ERR

Dynamic

OK or ERR

ERR

Movie1

OK or ERR

ERR

Movie2

OK or ERR

ERR
ERR

Picture Reset
Video INPUT

Picture Mode

RGB Frequency Check

Standby mode
(or 30-second startup time)

Power ON

Standard

Picture Reset
HDMI2

Parameter

Game

OK or ERR

Contrast

-30 - +30

OK or ERR

ERR

Bright

-30 - +30

OK or ERR

ERR

Color

-30 - +30

OK or ERR

ERR

Tint

-30 - +30

OK or ERR

ERR

Sharp

-30 - +30

OK or ERR

ERR

Red

-30 - +30

OK or ERR

ERR

Blue

-30 - +30

OK or ERR

ERR

CLR Temp

-2-+2

OK or ERR

ERR

Picture Reset

OK or ERR

ERR

Horizontal

kHz (***.* or ERR)

ERR

Vertical

Hz (***.* or ERR)

ERR

OK, ERR

Lamp Timer Reset *2

Note
• If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value
in the range indicated in brackets under CONTROL CONTENTS.
*1
*2

For setting the projector name, send the commands in order of PJN1, PJN2 and PJN3.
The Lamp Timer Reset command can only be sent in standby mode.

-56

XV-Z15000̲E̲US.indb 56

2008/12/25 14:25:51

Computer Compatibility Chart
Computer
• Multiple signal support
Horizontal Frequency: 15–110 kHz, Vertical Frequency: 43–85 Hz, Pixel Clock: 12–170 MHz
• Compatible with sync on green and composite sync signals (TTL level)
PC/MAC

Mode

Resolution

Horizontal frequency
[kHz]

Vertical
frequency[Hz]

Analog
Support

60
70
85
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
60
60
60
60
60
60
70
75
60
60
60
60
60
60
60

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

SXGA+

1400 × 1050

WSXGA+

1600 × 900
1680 × 1050
1920 × 1080*1

27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.3
35.2
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.8
49.7
47.7
47.8
55.9
55.0
66.2
67.5
60.0
64.0
64.0
65.3
55.9
65.3
66.8

1920 × 1080*2

67.5

✔

640 × 480
832 × 624
1024 × 768
1152 × 870

34.9
49.7
60.2
68.7

67
75
75
75

✔
✔
✔
✔

640 × 400

720 × 400
VGA

640 × 480

SVGA

800 × 600

XGA

1024 × 768

1280 × 720
1280 × 768
1280 × 800
1360 × 768
1366 × 768
1440 × 900

WXGA

WXGA+

1152 × 864
SXGA
1280 × 960
1280 × 1024

MAC
MAC
MAC
MAC

13"
16"
19"
21"

VGA
SVGA
XGA
SXGA

Digital
Support

Display

✔

✔
✔
✔

✔
✔
✔
✔
Upscale
✔
✔
✔
✔

✔
✔
✔
✔
✔
✔
✔
Down sampled
Intelligent
Compression

✔

Upscale

*1 When a 1920 × 1080 analog signal is input, the image is compressed before it is displayed on the screen.
*2 Full image display when “Resolution” is set to “1920 × 1080”

Note
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data
in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s
operation manual.
• When “Screen resolution” of the computer is different from the resolution displayed on the projected image, follow the procedures shown below.
– Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in “Screen
resolution” of the computer.
– Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution” adjustment. Check the settings of the computer's signal output. If the settings cannot be
changed, it is recommended that the resolution be set to “1920 × 1080” or “1280 × 720”.
DTV
Vertical
Frequency (Hz)
60

Analog
Support
✔

Digital
Support

Signal

31.5

✔

540P

33.8

✔

1080I
1080P

576I
576P

15.6

✔

1080P

31.3

✔

1080P

720P

37.5

✔

1080P

56.3

✔

720P

45.0

✔

1080P

67.5

✔

480I
480P

1080I

Horizontal
Frequency (kHz)
28.1

Vertical
Frequency (Hz)
50

Analog
Support
✔

Digital
Support
✔

33.8

✔

27.0

✔

28.1

✔

33.8

Appendix

Horizontal
Frequency (kHz)
15.7

Signal

✔

-57

XV-Z15000̲E̲US.indb 57

2008/12/25 14:25:52

Troubleshooting
Problem

Check
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The lens shutter is closed.
• The selected input mode is wrong.
• Cables are incorrectly connected to the projector.
• Remote control battery has run out.
• External output has not been set when connecting notebook computer.

No picture or projector does
not start

• The lamp unit cover is not installed correctly.

Page
22
–
22, 27
26, 40, 41
18-22
12
–
51, 52

• The selected “Signal Type” is wrong.

• The video signal format of the video equipment is not set correctly.

• “Bright” is set to minimum position.

• Image adjustments are incorrectly set.

(S-VIDEO or VIDEO input)
• Video input system is incorrectly set.
(COMPONENT, COMPUTER/COMPONENT or HDMI1, 2 input)
• Input signal type is incorrectly set.

41
40

Color is faded or poor.

Picture is blurred;
noise appears.

An unusual sound is
occasionally heard
from the cabinet.
Maintenance
indicator on the
projector illuminates.
Picture is green when receiving
component signals and the video
equipment is connected to the
COMPONENT or COMPUTER/
COMPONENT terminal on the
projector.
Picture is pink when receiving RGB signals and the video
equipment is connected to the
COMPONENT or COMPUTER/
COMPONENT terminal on the
projector.
The black levels of the
image show banding or
appear faded when HDMI1
or 2 is selected.
Picture is too bright and
whitish.

• Adjust the focus.

• The projection distance exceeds the focus range.

(Computer input)
• Perform “SIG-ADJ” Adjustments (“Clock” Adjustment)
• Perform “SIG-ADJ” Adjustments (“Phase” Adjustment)
• Noise may appear depending on the computer.
• The “DNR” (Digital Noise Reduction) or “MNR” (Mosquito Noise Reduction) setting is not correct.
• There is fog on the lens. If the projector is carried from a cold room into a
warm room, or if it is suddenly heated, condensation may form on the surface
of the lens and the image will become blurred. Please set up the projector at
least one hour before it is to be used. If condensation should form, remove the
power cord from the wall outlet and wait for it to clear.
• If the picture is normal, the sound is due to cabinet shrinkage caused
by a room temperature changes. This will not affect operation or performance.
• See “Maintenance Indicators”.

40
40
–
39
–

–

• Change the input signal type setting.

• Make adjustments that result in the best picture quality in the “Dynamic
Range” setting.

• Image adjustments are incorrectly set.

-58

XV-Z15000̲E̲US.indb 58

2008/12/25 14:25:53

Problem
The cooling fan
becomes noisy.
The lamp does not light up
even after the
projector turns on.

Check
• When temperature inside the projector increases, the cooling fan runs
faster.
• The lamp indicator is illuminating in red.
Replace the lamp.
• The lens shutter is opened fully.

Page
–
22, 48, 51

The lamp suddenly turns off
during projection.
The image sometimes
flickers.

The lamp needs much time
to turn on.

• Cables are incorrectly connected to the projector or the connected equipment works improperly.
• If this happens frequently, replace the lamp.

18-21
51

• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.

• Non-Sharp Video Products are connected.
One Touch Play function may not work when the projector is connected
to non-Sharp Video Products.

• An HDMI cable is not used for connection between the projector and the
Sharp Video Products.
One Touch Play function is enabled when the projector is connected to
the Sharp Video Products with an HDMI cable.

• One Touch Play function of the projector is not set to “On”.

Picture is dark.
One Touch Play is not
enabled.

System Standby is not
enabled.

• CEC settings of connected Sharp Video Products or other CEC devices
are incorrect.

–

• One Touch Play is set to “Off” and disabled when the Economy mode is
set to “On”.

• Non-Sharp Video Products are connected.
System Standby function may not work when the projector is connected
to non-Sharp Video Products.

• An HDMI cable is not used for connection between the projector and the
Sharp Video Products.
System Standby function is enabled when the projector is connected to
the Sharp Video Products with an HDMI cable.

• System Standby function of the projector is not set to “On”.

• CEC settings of connected Sharp Video Products or other CEC devices
are incorrect.

–

A response code cannot be
received when the
projector was attempted
to be controlled using
RS-232C commands from
a computer during standby.

• In the case of transmitting RS-232C commands from a computer during
standby, it takes a maximum of 30 seconds for the computer to receive
the response code. Set the response code waiting time of the computer
to 30 seconds or more.

The remote control
cannot be used.

• Operate the remote control while pointing it at the projector’s remote
control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent light is shining on the projector’s
remote control sensor, place the projector where it will not be affected by
strong light.

• The batteries may be depleted or inserted incorrectly. Make sure the batteries are inserted correctly or insert new ones.

12
12

Appendix

This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect
operation or interference. If this should happen, unplug the unit and plug it in again after more than
5 minutes.

-59

XVZ15000̲E̲US̲09.indd 59

2009/01/14 15:43:05

For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting”
section on pages 58 and 59. If this operation manual does not answer your question, please contact the
SHARP Service departments listed below.
U.S.A.

Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
lcdsupport@sharpsec.com
http://www.sharpusa.com

Canada

Sharp Electronics of Canada Ltd.
(905) 568-7140
http://www.sharp.ca

Mexico

Sharp Electronics Corporation
Mexico Branch
(525) 716-9000
http://www.sharp.com.mx

Latin America Sharp Electronics Corp. Latin
American Group
(305) 264-2277
www.servicio@sharpsec.com
http://www.siempresharp.com

Benelux

SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
http://www.sharp.nl
http://www.sharp.be
http://www.sharp.lu

Australia

Sharp Corporation of Australia Pty.
Ltd.
1300-135-022
http://www.sharp.net.au

New Zealand Sharp Corporation of New Zealand
Phone: (09) 573-0111
Fax: (09) 573-0112
http://www.sharp.net.nz
Singapore

Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
ckng@srs.global.sharp.co.jp
http://www.sharp.com.sg

Hong Kong

Sharp-Roxy (HK) Ltd.
(852) 2410-2623
dcmktg@srh.global.sharp.co.jp
http://www.sharp.com.hk

Germany

Sharp Electronics (Europe) GMBH
01805-234675
http://www.sharp.de

U.K.

Sharp Electronics (U.K.) Ltd.
08705 274277
http://www.sharp.co.uk/customersupport

Italy

Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
http://www.sharp.it

Taiwan

Sharp Corporation (Taiwan)
0800-025111
http://www.sharp-scot.com.tw

France

Sharp Electronics France
01 49 90 35 40
hotlineced@sef.sharp-eu.com
http://www.sharp.fr

Malaysia

Sharp-Roxy Sales & Service Co.
(60) 3-5125678

U.A.E.

Sharp Middle East Fze
971-4-81-5311
helpdesk@smef.global.sharp.co.jp

Thailand

Sharp Thebnakorn Co. Ltd.
02-236-0170
svc@stcl.global.sharp.co.jp
http://www.sharp-th.com

Korea

Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
lcd@sharp-korea.co.kr
http://www.sharpkorea.co.kr

India

Sharp Business Systems (India)
Limited
(91) 11- 6431313
service@sharp-oa.com

Spain

Switzerland

Sweden

Austria

Sharp Electronica Espana, S.A.
93 5819700
sharplcd@sees.sharp-eu.com
http://www.sharp.es
Sharp Electronics (Schweiz) AG
0041 1 846 63 11
cattaneo@sez.sharp-eu.com
http://www.sharp.ch
Sharp Electronics ( Nordic ) AB
(46) 8 6343600
vision.support@sen.sharp-eu.com
http://www.sharp.se
Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123
pogats@sea.sharp-eu.com
http://www.sharp.at

-60

XV-Z15000̲E̲US.indb 60

2008/12/25 14:25:53

Specifications
Model

XV-Z15000

Display devices

0.65" DLP® Chip × 1

Resolution

1080P (1920 × 1080)

Lens

Input terminals

Control and
communication
terminals

F number

F 2.5 – 2.7

Zoom

Manual, ×1.15 (f = 21.0 – 24.2 mm)

Focus

Manual

HDMI

×2

Computer/Component
(mini D-sub 15 pin)

×1

Component (3RCA)

×1

S-Video (mini DIN 4 pin)

×1

Video (RCA)

×1

RS-232C (mini D-sub 9 pin)

×1

Projection lamp

250 W

Rated voltage

AC 100 – 240V

Rated frequency

50/60 Hz

Input current

3.7 A

Power consumption (Standby)

353 W (7.6 W) with AC 100 V
339 W (8.3 W) with AC 240 V

Operation temperature

41°F to 95°F (+5°C to +35°C)

Cabinet

Plastic

Dimensions (main body only) [W × H × D]

15 3/4" × 3 15/16" × 13 13/64"
(400 × 100 × 335 mm)

Weight (appprox.)

12.8 lbs. (5.8 kg)

As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

Appendix
-61

XV-Z15000̲E̲US.indb 61

2008/12/25 14:25:54

Dimensions

4 17/32 (115)

3 15/16 (100)

1 43/64
(42.2)

13 13/64 (335)

1/4

(6)

Units: inches (mm)

4 17/32
(115)
15 3/4 (400)

1 13/16
(45.75)

/64 (5.75)

7 5/64
(179.75)

6 49/64 (171.5)

3 33/64
(89)

1 1/2
(38)

1/8 (3)

3 23/64
(85)

2 61/64
(75)

4 5/8
(116.25)

-62

XV-Z15000̲E̲US.indb 62

2008/12/25 14:25:54

Index
Accessories ............................................................ 8
AC socket ............................................................. 22
Adjustment buttons ............................................. 34
Adjustment feet .................................................... 23
Advanced ............................................................. 37
All Reset ............................................................... 46
Auto Power Off ..................................................... 45
Auto Sync ............................................................. 40
AUTO SYNC button ............................................. 27
AUTO V-KEYSTONE button ................................. 25
Background .......................................................... 44
Batteries ............................................................... 12
Bright .................................................................... 36
Bright Boost ......................................................... 39
Carrying handle .................................................... 10
Ceiling-mount setup ............................................. 16
CINEMA ZOOM .................................................... 29
Clock .................................................................... 40
CLR Temp (Color Temperature) ............................ 36
C.M.S. .................................................................. 37
Color ..................................................................... 36
COMPONENT button ........................................... 26
COMPONENT terminal ......................................... 18
COMPUTER button .............................................. 26
COMPUTER/COMPONENT terminal ............. 18, 20
Contrast ................................................................ 36
Detail Enhance ..................................................... 39
DNR ...................................................................... 39
DOT BY DOT ........................................................ 30
Dynamic ............................................................... 36
Dynamic Range .................................................... 41
Economy Mode .................................................... 45
ECO+QUIET button .............................................. 28
Effect .................................................................... 38
ENTER button....................................................... 34
Fan Mode ............................................................. 46
Film Mode............................................................. 39
Focus ring............................................................. 23
FREEZE button ..................................................... 27
Game .................................................................... 36
Gamma ................................................................. 37
HDMI1, 2 buttons ................................................. 26
HDMI1, 2 terminals ......................................... 18, 19
HEIGHT ADJUST lever ......................................... 23
H-Image Shift ................................................. 26, 42
H-Pos ................................................................... 40
Hue ....................................................................... 38

Kensington Security Standard connector ............ 10
KEYSTONE button ............................................... 24
Lamp indicator ..................................................... 48
Lamp Timer (Life) .................................................. 46
Language (on-screen display language) .............. 44
Lens shutter.............................................. 22, 27, 51

Natural .................................................................. 36
ON button ............................................................. 22
One Touch Play .................................................... 45
On-screen Display ................................................ 44
Optional accessories .............................................. 8
OSD Brightness .................................................... 44
Overscan .............................................................. 42
Phase.................................................................... 40
Picture .................................................................. 36
Picture Mode ........................................................ 36
PICTURE MODE button ....................................... 27
Power cord ....................................................... 8, 22
Power indicator .............................................. 22, 48
PRJ-ADJ ............................................................... 45
PRJ mode ....................................................... 16, 44
Remote control ..................................................... 11
Remote control sensors ....................................... 12
Replacing the lamp .............................................. 50
RESIZE button ...................................................... 29
RETURN button .................................................... 34
Rotation .......................................................... 25, 44
RS-232C ............................................................... 46
RS-232C terminal ................................................. 21
Saturation ............................................................. 38
SCR-ADJ .............................................................. 42
Screen Size and Projection Distance ................... 17
Security bar .......................................................... 10
Select Color .......................................................... 38
Sharp .................................................................... 36
SIG-ADJ ............................................................... 40
Signal Info............................................................. 41
Signal Type ........................................................... 40
SMART ZOOM ..................................................... 30
Sphere ............................................................ 25, 43
Standard ............................................................... 36
STANDBY button .................................................. 22
STANDBY/ON button ........................................... 22
STRETCH ............................................................. 29
S-VIDEO button .................................................... 26
S-VIDEO terminal ........................................... 18, 19
System Standby ................................................... 45
Temperature warning indicator ............................. 48
Tint........................................................................ 36
Value ..................................................................... 38
VIDEO button ....................................................... 26
Video Setup .......................................................... 41
Video System ....................................................... 41
VIDEO terminal ..................................................... 18
V-Image Shift .................................................. 26, 42
V-Pos .................................................................... 40
ZOOM 14:9 ........................................................... 30
Zoom ring ............................................................. 23

Appendix

IMAGE SHIFT button ............................................ 26
INPUT button........................................................ 26
Input Name ........................................................... 46
IRIS1, 2 ................................................................. 37
IRIS1, 2 buttons.................................................... 28

MAGNIFY buttons ................................................ 28
MENU HIDE button .............................................. 28
MENU button........................................................ 34
MNR ..................................................................... 39
Movie1, 2 .............................................................. 36

-63

XV-Z15000̲E̲US.indb 63

2008/12/25 14:25:54

OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO

FRANÇAIS

XV-Z15000

PROJECTOR
PROJECTEUR
PROYECTOR
PROJETOR

ENGLISH

XV-Z15000

ESPAÑOL
PORTUGUÊS

SHARP CORPORATION

Printed in China
Imprimé en Chine
Impreso en China
Impresso na China
TINS-E012WJZZ
09P01-CH-NM

XVZ15000̲E̲US̲Hyo1-4.indd 1

2008/12/25 15:07:12

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2009:02:09 14:25:23+01:00
Create Date                     : 2009:01:22 10:17:16+09:00
Metadata Date                   : 2009:02:09 14:25:23+01:00
Creator Tool                    : Adobe InDesign CS2_J (4.0.5)
Format                          : application/pdf
Title                           : XV-Z15000 Operation-Manual GB
Description                     : Operation Manual, extract of language English
Creator                         : SCEE-Smolka
Subject                         : XV-Z15000 XVZ15000 projector
Document ID                     : uuid:dd155bc8-6e48-440e-816e-e46c79b8ed5f
Instance ID                     : uuid:07d06f27-e788-4432-8b90-14ca6ad8bc6d
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Trapped                         : True
GTS PDFX Conformance            : PDF/X-1a:2001
GTS PDFX Version                : PDF/X-1:2001
Page Count                      : 66
Page Layout                     : SinglePage
Author                          : SCEE-Smolka
Keywords                        : XV-Z15000, XVZ15000, projector

EXIF Metadata provided by EXIF.tools

Sharp XV Z15000 Operation Manual GB User To The 7d80eb15 401d 481d 8058 56501956d7b4

Navigation menu

Versions of this User Manual:

Views

Navigation