Sharper Image INSTRUCTION MANUAL OF IW001 WF JJY 204059
User Manual: Sharper Image Color Weather Station @ Sharper Image
Open the PDF directly: View PDF .
Page Count: 9
Download | |
Open PDF In Browser | View PDF |
INSTRUCTION MANUAL COLOR WEATHER FORECAST STATION P. 1 FEATURE LIST 4.7” / 120mm (diagonal) display with 1.1” time digits Alarm 1 and Alarm 2 Programmable Snooze 5-60 minutes Dimmer for nighttime viewing Color forecast : Sunny, Partly Cloudy, Cloudy, Rainy, Stormy 12-hour forecast based on changing air pressure Tendency indicator of weather forecast Indoor-outdoor temperature and humidity (RH%) Max-Min records of temperature and humidity Month-Date Calendar interchangeable with Air pressure readout (inHg) Degree C/F readout 12/24 hour time format 433Mhz wireless outdoor transmitter (one transmitter is included) Up to 50-meter transmission of outdoor temperature and humidity Auto scrolling of outdoor temperatures and humidity of up to three transmitters Low battery indicator of outdoor transmitter Can expand to use with two additional outdoor transmitters (purchase separately) Main unit powered by external AC/DC adaptor Batteries : 3 “AAA” alkaline for backup of the main weather station (not included) : 2 “AAA” alkaline for outdoor transmitter (not included) QUICK SETUP Step 1: Power up your weather station Insert the AC/DC adaptor to any 120V AC household outlet. Then insert the DC jack to the back case of your unit. Take out the stand at the back case and insert it horizontally to the back case, then rotate it by 90 degree to secure it to the back case. Step 2: install batteries to your outdoor transmitter Keep your weather station and wireless outdoor transmitter next to each other. Slide open the battery cover at the back of your wireless outdoor transmitter, then insert 2 x AAA alkaline batteries to the battery compartment. Make sure the Channel selector is at 1 position. Replace the battery cover. Remark : Make sure (Channel 1) is displayed under the outdoor temperature and humidity. You could press / CHANNEL to select Channel 1. Your weather station will receive data signal from the outdoor transmitter in few seconds. Then place your outdoor transmitter in a dry and shaded area. P. 2 Installing backup batteries to your weather station Your weather station requires 3 “AAA” alkaline batteries to provide backup power to it in the event of a temporary power interruption. 1. 2. 3. 4. Place your unit face down on a flat surface. Slide and remove the battery cover at the bottom of your unit. Insert 3 “AAA” alkaline batteries into the battery compartment by observing the “+” and “-“ polarity as indicated. Replace the battery cover. If the AC main power is interrupted, the backlight will go off. The backup batteries will keep the time and all settings of your unit. Press once to turn on the backlight for 5 seconds. Remarks: Keep in mind that your outdoor transmitter has a 180-ft open air transmission with no obstructions. Actual transmission range will vary depending on what is in the path of the signal. Each obstruction (roof, walls, floors, ceilings, thick trees, etc.) will effectively cut signal range in half. Insert the holder to the bottom of the outdoor transmitter for desktop or insert it to the back of the transmitter for wall mount purpose. TO SET YOUR UNIT MANUALLY The setting of your unit comes into the sequence of 12/24 hour, hours, minutes, year, month, date, monthdate/date-month display and snooze duration. 1. Press and hold for 2 seconds, time digits change to “12Hr“ and flash. Press or to select “24 Hr” time format if need. When 12Hr time format is selected, PM indicator will be displayed. 2. Then press once again, “12” the hour digits flash. Press or button to set the hours. Press and hold / will accelerate your setting faster. 3. Then press once again, “00”” the minute digits flash. Press or button to set the minutes. Press and hold / will accelerate your setting faster. 4. Then press set the year. once again, “Yr” and “2013” digits flash. Press or button to P. 3 5. Then press once again, month digits flash. Press or button to set the month. 6. Then press once again, date digits flash. Press or button to set the date. 7. Then press once again, “m”, “d”, month-date digits flash. Press or to select month-date “m” “d” or date-month “d” “m” calendar display. 8. Then press once again, “SN” and “05”. Press or button to set the snooze duration from 5 minutes to 60 minutes. 9. Press to return to normal mode, or it will return to normal mode in around 10 seconds if no further press of any other buttons. TO SET ALARM TIME 1. Press and hold alarm time. once, time digits change to alarm time digits “6:00” and “A1”. Then press for 2 seconds, the alarm hour digits flash. Press or to set the hours of your desired 2. Then press once again, the alarm minute digits flash. Press or button to set the minutes of your desired alarm time. 3. Press once, time digits change to alarm time digits “6:00” and “A2” is displayed. Then repeat the above in Alarm 1 setting. P. 4 3. Your weather station will return to normal mode, or it will return to normal mode in around 10 seconds if no further press of any other buttons. TO TURN ON OR OFF YOUR DAILY ALARM Simply press to turn on or off the Alarm 1, Alarm 2, or Alarm 1 & 2. When Alarm 1 is turned on, the appears. When Alarm 2 is turned on, the appears. TO USE SNOOZE ALARM When time reaches your set alarm time, your weather station will give a beep sound to wake you up. The corresponding or will flash. 1) Press once to stop the alarm temporarily, the corresponding The alarm will beep again according to your set snooze duration. or 2) When the alarm is sounding, press once, the alarm beep will stop, become static, alarm will beep again at the same time next day. keeps flashing. or Alarm Duration: 2 minutes TO USE THE DIMMER Press button once to adjust the display brightness for nighttime viewing. TO DISPLAY TEMPERATURE IN DEGREE °C OR °F Simply press (°C/°F) to display temperature in degree °C or degree °F. WEATHER FORECAST AND PRESSURE TREND INDICATOR Your weather station has a built-in barometric sensor which measures the change of the air pressure over time. Your weather station takes around 12 hours to gather and average air-pressure readings to provide a weather forecast for next 12 hours. WEATHER ICONS There are five possible types of weather icons that will be displayed: SUNNY SUNNY AND CLOUDY (PARTLY SUNNY) CLOUDY P. 5 RAINY STORMY FROST ALERT Frost Alert Icon appears when outdoor temperature is below +3°C AIR PRESSURE TENDENCY INDICAOTRS When the arrow appears, the air pressure is increasing, the weather is expected to improve. When the arrow appears, the air pressure is decreasing, the weather is expected to become worse. When the arrow appears, the air pressure change is stable. Remarks: Moving your weather station from one floor of a building to another floor will affect the accuracy of your weather station, which should operate at the same altitude all the time. If you move it to a new location, it will take 12 hours to get stable and accurate again. Our weather station provides next 12-hour weather forecast. It may not match with the current weather condition outside. TO DISPLAY AIR PRESSURE READOUT Press and hold until the calendar display shows the air pressure readout in inHg. Press and hold again to revert back to calendar display. TO READ MAXIMUM-MINUMUM IN-OUT TEMPERATURES AND HUMIDITIES Simply press the to view the maximum indoor-outdoor temperatures and humidities records with “MAX” icons appearing on the display. Press again to view the minimum indoor-outdoor temperatures and humidities and the air pressure with “MIN” icons appearing on the display. When the maximums or minimums are displayed, press and hold the start to record the maximums and minimums again. to reset both records and it will IF YOU LOSE THE OUTDOOR TEMPERATURE AND HUMIDITY When the outdoor temperature and humidity digits show '---", the wireless transmission is either interrupted or lost. Press and hold the / CHANNEL button to start searching for the signal from the outdoor transmitter with the flashing. If you continue to lose the outdoor temperature and humidity display, which could happen in extreme cold weather, try placing the transmitter in a different location until you have smooth transmission of temperature / humidity data. P. 6 HOW TO SYNCHRONIZE YOUR WEATHER STATION WITH ANOTHER OUTDOOR TRANSMITTER 1. Press / CHANNEL at the back of your weather station, and humidity. icon appears under your outdoor temperature 2. Press and hold / CHANNEL until the icon blinks, your weather station is searching for the signal of another outdoor transmitter at Channel 2. 3. Slide open the battery door of your second transmitter, slide the switch to the middle position marked with 2, then insert two AAA batteries into the battery compartment by observing the correct +/- polarity. Replace the battery cover. 4. The outdoor temperature and humidity of your second transmitter will appear on the LCD together with icon within few seconds. If the data still does not appear, press RESET at the front of your second transmitter once. 5. To synchronize your weather station with a third outdoor sensor, repeat the same step by choosing on your weather station and select 3 on your third transmitter. AUTO SCROLLING THE OUTDOOR TEMPERATURE AND HUMIDITY OF DIFFERENT TRANSMITTER Press / CHANNEL one at a time until the icon flashes. Then the outdoor temperature and humidity of different outdoor transmitter will be displayed for few seconds alternately with , , flashing. To stop the auto scrolling, press / CHANNEL once to go back to constant display of the temperature and humidity of the transmitter, the icon remains static on the display. LOW BATTERY INDICATION OF YOUR OUTDOOR TRANSMITTER The icon will appear to indicate the battery level of your outdoor transmitter is getting low. You may need to replace the batteries of your outdoor transmitter with new ones. Extreme cold weather (e.g. below 14 °F) will also cause low battery voltage. TROUBLESHOOTING In case your weather station clock shows irrelevant information or digits, it maybe affected by electrostatic discharge or interferences from other devices. Use a sharp object to press RESET. Your unit will be reset to default settings and you need to set the time, calendar and alarm time again. P. 7 Problem LCD is blank No Outdoor Temperature and Humidity is displayed Temperature, humidity, or air pressure is incorrect Solution 1. Press RESET on the main unit. 2. Replace fresh batteries in your weather station. 1. Press and hold ▲/ CHANNEL on the weather station. 2. Press and hold▲/ CHANNEL then press RESET on the outdoor transmitter. 3. Make sure the correct channel is selected on your weather station (default setting is – Channel 1) 4. Observe if the Low Battery icon appears on the left of the outdoor temperature. If yes, replace batteries in outdoor sensor with fresh alkaline batteries. 5. No other interfering sources are being used (such as computer monitors, TV sets, headphones, or speakers) in the path of signal from the outdoor sensor. The signal travels in a straight line, an electrical source near that “line” may cause interference. 1. Press RESET on the main unit. 2. Make sure your main unit and the outdoor transmitter is away from sources of heat / cold / direct sunshine. CARE OF YOUR WEATHER SATATION CLOCK 1. 2. 3. 4. 5. Do not expose the unit to extreme temperature, water or direct sunlight. Avoid contact with any corrosive materials. Do not subject the unit to excessive force, dust or humidity. Do not open the inner back case or tamper with any components of this unit. Do not plug in any other AC/DC adaptor with incorrect specifications or voltage. SPECIFICATIONS: Temperature Range Indoor +32°F to +122°F (0°C to +50°C) (display shows HH.H / LL.L if out of this range) Outdoor -58°F to +158°F (-50°C to +70°C) (display shows HH.H / LL.L if out of this range) Humidity Range Indoor Outdoor 20% - 95% 20% - 95% Temperature Resolution RH% Resolution Temperature & Humidity RF Transmission distance Alarm Duration Snooze Duration 0.2°F / 0.1°C 1% measure every 30 seconds up to 180 feet line-of-sight distance 2 minutes 5 minutes FCC Disclaimer This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. P. 8 Words in the figure: Figure 1: ENGLISH Outdoor humidity Outdoor sensor channel 1/2/3 Max / Min temperature & Humidity data Outdoor temperature Outdoor sensor low battery icon Barometric Pressure Weather forecast Storm warning icon Indoor humidity Frost alarm icon Indoor temperature Alarm 1 Alarm 2 Month/Day/Date Figure 2: SNOOZE / BACKLIGHT / CHANNEL SET / ALARM SET ALARM ON/OFF MEMORY (°C/°F) RESET BATTERY / BATTERY COVER HANGING HOLE STAND DESK STAND SLOT Figure 3: OUTDOOR TRANSMITTER LED INDICATOR RESET BATTERY COVER CHANNEL 1,2,3 SELECTOR FOOT / HANGER P. 9 Other Language
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : * Create Date : 2015:10:06 14:40:28-04:00 Modify Date : 2015:10:06 14:40:47-04:00 Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : * Title : INSTRUCTION MANUAL OF IW001-WF-JJY Creator Tool : Microsoft® Word 2010 Metadata Date : 2015:10:06 14:40:47-04:00 Producer : Microsoft® Word 2010 Document ID : uuid:72d36363-b3aa-448a-aab7-348d2e58ce0a Instance ID : uuid:86effb75-554b-4c4f-a023-aa58eaece56a Page Count : 9EXIF Metadata provided by EXIF.tools