Sheenway Asia ZW3007 wireless relay User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2062211
Application ID	KG2QLTEN0699iXzXlyUvCw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	47.76kB (596982 bits)
Date Submitted	2013-09-04 00:00:00
Date Available	2013-09-04 00:00:00
Creation Date	2013-07-23 16:26:24
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2013-07-23 16:26:27
Document Title	User manual
Document Creator	Adobe InDesign CS6 (Macintosh)

Z-Wave® Certified
Wireless Lighting Control
On/Off/Dim
Dimmer Switch
45716_45717
ZW3007
Made in China
Introduction:
Thank you for your purchase of a Jasco Z-Wave® control
device. Z-Wave technology is designed to automate
lighting/home control and provide easy remote operation
of all your Z-Wave enabled devices.The Jasco Z-Wave
product family includes a variety of devices to control
lighting in your home. It is up to you whether you want to
control one room or your entire house and whether you
want to do it all now or start with one room and add more
over time.
This dimmer is one component of
a Z-Wave® control system and is
designed to work with all other
Z-Wave enabled devices in a home
control network. It will also act as
a wireless repeater to insure that
commands intended for another
device in the network are
received, thereby extending the
range of the wireless controller.
Z-Wave devices of other types
and brands can be added
to the system and will also
act as range extenders if
they support this function
of repeating the signal
received to other nodes
in the system.
Air gap switch
Dimmer switch
CAUTION
This device is intended for installation in accordance
with the National Electric Code and local regulations
in the United States, or the Canadian Electrical Code
and local regulations in Canada. If you are unsure or
uncomfortable about performing this installation
consult a qualified electrician.
This switch is designed for use only with permanently
installed incandescent fixtures. Do not use it to control
fluorescent lighting, transformer supplied lighting/appliances
or receptacles. The incandescent lighting controlled by this
dimmer switch must not exceed 600 watts.
NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT
Z-Wave enabled devices should never be used
to supply power to or control the On/Off status
of medical and/or life support equipment!
WARNING
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
Controlling Appliances:
Exercise extreme caution when using Z-Wave devices to
control appliances. Operation of the Z-Wave device may
be in a different room than the controlled appliance, also an
unintentional activation may occur if the wrong button on the
remote is pressed. Z-Wave devices may automatically be
powered on due to timed event programming. Depending upon
the appliance, these unattended or unintentional operations
could possibly result in a hazardous condition. For these
reasons, we recommend the following:
1.
Assign Z-Wave controlled appliances to device
numbers 10 – 18 on the Jasco remote. The likelihood of
unintentionally turning on the appliance will be reduced
significantly because the “Shift” button will need to be
pressed before pressing device numbers 10-18.
2. Z-Wave devices controlling appliances should be
removed from “All” control setting. Instructions on how
to do this are included in the manual for your Jasco
remote.
3. Do Not include Z-Wave devices in Groups or Scenes if
they control appliances.
4. Do Not use Z-Wave devices to control electric heaters
or any other appliances which may present a hazardous
condition due to unattended or unintentional or
automatic power on control.
5. Double check programs for accuracy before using them.
Wireless Range
This device complies with the Z-Wave standard of openair, line of sight transmission distances of 65 feet. Actual
performance in a home depends on the number of
walls between the remote controller and the destination
device, the type of construction and the number of
Z-Wave enabled devices installed in the control network.
Every Z-Wave enabled device acts as a signal repeater
and multiple devices result in more possible transmission
routes which helps eliminate “RF dead-spots”.
Things to consider regarding RF range:
• Each wall or obstacle (i.e.: refrigerator, big screen TV,
etc.) between the remote or Z-Wave device and the
destination device will reduce the maximum range by
approximately 25-30%.
• Brick, tile or concrete walls block more of the RF signal
than walls made of wooden studs and plasterboard (drywall).
• Wall mounted Z-Wave devices installed in metal
junction boxes may suffer a significant loss of range
(approximately 20%) since the metal box blocks a large
part of the RF signal.
WIRING CONFIGURATION CONSIDERATIONS: Prior
to beginning wiring your Jasco Z-Wave dimmer, please
note that this dimmer requires a neutral wire connection
in order to function properly. If the location that you wish
to install this dimmer switch does not have a neutral wire
present, you may need to contact a licensed electrician
to have a neutral wire brought to the switch location.
Effects of Home Construction on Wireless Range
Between Z-Wave Enabled Devices.
Note: The distances shown in the table below are typical
examples. Actual performance in your home will vary.
From the Remote (or repeating Z-Wave module) to
destination device:
Type of Construction
Wood Frame Brick, Tile or
w/Drywall
Concrete
Plastic
Metal
Plastic
Metal
J-Boxes* J-Boxes J-Boxes* J-Boxes
Number
of Walls or
Obstacles
0** 100’
80’
100’
80’
70’
56’
60’
48’
34’
27’
21’
17’
49’
39’
36’
29’
* For Plug-in Modules or In-Wall Devices Installed, Plastic
Junction Boxes
** Line of Sight / no obstructions
Please Note: Z-Wave home control networks are designed to
work properly alongside 802.11 wireless computer networks,
Bluetooth and 2.4GHz, 5.8GHz or DECT devices. Some baby
cams, wireless video devices and older cordless phones using
the 900MHz frequency range may cause interference and limit
Z-Wave functionality. Many 900MHz products have a switch to
select channel “A” or “B”. You may find that one of these channels
will cause less interference than the other.
IMPORTANT NOTE ABOUT 3-WAY CIRCUITS
The term “3-way circuit” refers to a circuit with two switches
and one load (light) like you find at the top and bottom of a
stairway. There are many ways to physically wire a 3-way
circuit and it is important to understand how the circuit you
wish to upgrade to Z-Wave control is wired. Below is a
description of a typical 3-way circuit.
One of the ways to wire a two-switch/one-load circuit is
to route the incoming power through the first switch, then
to the second switch and then to the load. Although very
common and by no means a standard, it is the easiest to
convert to Z-Wave control. With this type of circuit, Switch
1 is replaced by the Z-Wave auxiliary switch and Switch 2
is replaced with the primary Z-Wave switch. The auxiliary
switch does not actually control the power; instead, it sends
a momentary voltage signal through the traveler wire to the
primary switch which in turn, controls the power to the load.
Typical 3-way circuit:
Black
Black
Black
Colored (NOT GREEN)
White
Switch 1
Switch 2
Wrong Z-Wave switch position for typical
3-way circuit;
Black
(Load)
Black
(Line / Hot)
Black (Line / Hot)
Z-Wave
Primary
White
Z-Wave
Auxiliary
White
White (Neutral)
Correct Z-Wave switch position for typical
3-way circuit:
Black
Z-Wave
Auxiliary
White
Other
color
Z-Wave
Primary
Please consult an electrician if you have trouble identifying the
type of wiring circuit you wish to convert or if you do not feel
confident in your ability to convert the circuit to Z-Wave control.
INSTALLATION
This dimmer switch may be used in new installations or to
replace an existing wall switch. It may be used by itself for
2-way control (one switch & one load), with one Auxiliary
Switch* for 3-way control (two switches & one load) or with
two Auxiliary switches for 4-way control (three switches &
one load). When used by itself for 2-way control, please
make sure that the screw terminal for the traveler wire is
insulated (Do Not Remove the tape over the terminal if you
are not using the traveler connection).
Single Switch Wiring Schematic
White (Neutral)
Black
(Load)
ZWave
Primary
Green (Ground)
Black (Line / Hot)
3-Way Wiring Schematic using one Z-Wave primary
and one Z-Wave auxiliary
White (Neutral)
Traveler - Colored (Not Green)
ZWave
Auxiliary
Black
(Load)
ZWave
Primary
Green (Ground)
Black (Line / Hot)
4-Way Wiring Schematic using one Z-Wave primary
and one Z-Wave auxiliary
ZZ-Wave
Wave
Auxiliary
45610
Traveler - Colored
(Not Green)
Green (Ground)
White (Neutral)
Traveler - Colored (Not Green)
Z-Wave
Auxiliary
Green (Ground)
Black (Line / Hot)
Black
(Load)
Z-Wave
Primary
Single, Dual and Triple Gang Boxes
The metal plate surrounding the switch assembly is a
heat sink. The maximum load rating (600W) is provided
when installed in a single gang box with the full heat sink.
Multiple dimmer switches may be installed in dual or triple
gang boxes and, if necessary, one or both sides of the
heat sink may be removed by bending it at the score lines.
There is a corresponding reduction in the switch’s load
rating when ganged. DO NOT exceed the following loads:
Dimmer Rating Number of Dimmers
Heat Sink
600W
One switch in a Single Gang Box
500W
Two switches in a Double Gang Box
400W
Three switches in a Triple Gang Box
Full
One side
removed
Both sides
Traveler
Ground
Black
(Load)
Black
(HOT)
removed
WARNING
SHOCK HAZARD!
Turn OFF the power to the branch circuit at the circuit
breaker in your electrical service panel. Ensure power
is OFF before you install this device. All wiring connections
must be made with the POWER OFF to avoid personal
injury and/or damage to the switch.
1. Shut off power to the circuit at fuse box or 15A circuit breaker.
2. Remove wall plate. ! Warning: Verify power is OFF to
switch box before continuing.
3. Remove the switch mounting screws.
4. Carefully remove the switch from the switch box. DO NOT
disconnect the wires.
5. There are four screw terminals on the dimmer switch;
these are marked LINE (Hot), LOAD, GROUND and
TRAVELER. The Traveler terminal is only used for 3-way or
4-way wiring and should remain insulated if the dimmer is
being installed in a 2-way system (one switch & one load).
Match these screw terminals to the wires connected to the
existing switch (Do Not remove the tape over the terminal if
you are not using the traveler connection).
6. Disconnect the wires from the existing switch.
7. Connect the green or bare copper ground wire to the
GROUND terminal.
8. Connect the black wire that goes to the light to the terminal
marked LOAD.
9. Connect the black wire that comes from the electrical
service panel (Hot) to the terminal marked LINE. Note: UL
specifies that the tightening torque for the screws is
14 Kgf-cm (12 lbf-in).
10. OPTIONAL for 3 or 4-way control: Connect the Traveler
wire (usually Red) to the screw terminal marked TRAVELER.
The other end of this Traveler wire connects to the
TRAVELER screw terminal on the Auxiliary Switch. See
the following section for information about wiring the
Auxiliary Switch.
11. Insert Z-Wave Switch into the switch box being careful
not to pinch or crush wires.
12. Secure the switch to the box using the supplied screws.
13. Mount the wall plate.
14. Reapply power to the circuit at fuse box or circuit breaker
and test the system.
Optional for 3 or 4-Way Control:
1. The auxiliary switch requires the following 3 wiring connections:
a. The Traveler wire. This is used to send voltage signals to
the primary Z-Wave switch. The signals tell the Z-wave switch
what action to perform.
b. Ground.
c. Neutral.
2. DO NOT connect the auxiliary switch to the home’s black
Hot (Line) wire.
Observe Important Wiring Information
Important: This switch is rated for and intended to only be used
with copper wire.
The home’s electrical wires may be attached to the screw
terminals or inserted into the holes in the back of the switch
enclosure and clamped in place by tightening the screw
terminals. Always follow the recommended wire strip lengths
when making wiring connections.
Wire strip length:
• For attachment to screw terminals: Strip insulation 5/8” (max
14 AWG wire).
• For attachment using the enclosure’s holes: Strip insulation
5/8” (max 14 AWG wire).
You should now be able to use the rocker to manually turn
On/Off or adjust the brightness of the connected load.
Use your primary controller to include the switch in the home
control network after the switch is wired as shown in the above
diagram. It can then be added to groups and/or lighting scenes
and managed remotely to control the On/Off/Dim status of the
connected lighting.
Air Gap Switch
During normal operation, there is a small amount of power
passing through the switch to the load even when the
switch is turned off. The dimmer has an air gap switch
above the toggle (see diagram for location) to completely
disconnect power to the load. Slide the air gap switch LEFT
to disconnect the power while replacing light bulbs and slide
it to the RIGHT for normal operation. The air gap switch must
be all the way in for the switch to function and control
the lighting.
Key Features
• Remote On/Off/Brightness control via the
Z-Wave controller/network
• Manual On/Off/Brightness control with the front panel toggle
• Compatible with 2, 3, or 4 way wiring configurations
BASIC OPERATION
Remote Control
Jasco Z-Wave remotes provide control of an Individual
device, Groups of devices and Scenes. Other brands of
Z-Wave Certified remotes may not offer as much flexibility
in how you can set up your lighting control network. Please
refer to your remote control’s instructions for details on its
capabilities and instructions for adding and controlling devices.
Manual Control
The dimmer switch allows the user to: Turn ON/OFF and
control the brightness level of the connected lighting.
• To turn the connected lighting ON: Tap the toggle upwards.
• To turn the connected lighting OFF: Tap the toggle downwards.
• To brighten the connected lighting: Press and hold the
toggle upwards;
release when desired level is achieved.
• To dim the connected lighting; Press and hold the toggle
down; release when desired level is achieved. Please
note: holding the toggle until the light intensity is at the
minimum setting does not turn the power OFF; you
must still tap (press & release) the toggle downwards to turn
the power OFF.
• When OFF, holding the toggle downwards will cause the
lighting to go to the minimum dim level.
Program your Light Switch (Include or exclude the switch
to/from the Z-Wave home control network.)
• Refer to the instructions for your primary controller to access
the network setup function and include or exclude devices.
• When prompted by your primary controller, tap the toggle up
or down.
• The primary controller should indicate that the action
was successful. If the controller indicates the action was
unsuccessful, please repeat the procedure.
• Once the switch is part of the network, the same basic
procedure is used to add the switch to groups & scenes
or change advanced functions. Refer to the primary
controller’s instructions for details.
Note: After a power failure, the dimmer switch will
default to OFF.
• To turn the connected lighting ON: Tap the top of the rocker.
• To turn the connected lighting OFF: Tap the bottom of
the rocker.
• To brighten the connected lighting: Press and hold the top
of the rocker; release when desired level is achieved.
• To dim the connected lighting; Press and hold the bottom
of the rocker release when desired level is achieved. Please
note: pressing and holding the rocker until the light intensity
is at the minimum setting does not turn the power OFF; you
must still tap (press & release) the bottom of the rocker to turn
the power OFF.
• When OFF, pressing and holding the bottom of the rocker
will cause the lighting to go to the minimum dim level.
Program your Light Switch (Include or exclude the switch
to/from the Z-Wave home control network.)
• Refer to the instructions for your primary controller to
access the network setup function and include or
exclude devices.
• When prompted by your primary controller, tap the top or
bottom of the rocker.
• The primary controller should indicate that the action
was successful. If the controller indicates the action was
unsuccessful, please repeat the procedure.
• Once the switch is part of the network, the same basic
procedure is used to add the switch to groups & scenes
or change advanced functions. Refer to the primary
controller’s instructions for details.
Note: When the dimmer switch is registered with remote,
the dimmer switch will retain previous ON/OFF status after
a power failure, if the dimmer switch is not registered with
remote, the dimmer switch will default to OFF.
ADVANCED OPERATION
The following Advanced Operation parameters require that
you have an advanced controller like the Jasco model 45601
LCD remote. Advanced remotes from other manufacturers
may also be able to change these settings; however, basic
remotes do not have this capability.
All On/All Off
Depending upon your primary controller, the dimmer switch
can be set to respond to ALL ON and ALL OFF commands in
up to four different ways. Some controllers may not be able to
change the response from its default setting. Please refer to
your controller’s instructions for information on whether or not
it supports the configuration function and if so, how to change
this setting.
1. The four possible responses are:
2. It will respond to ALL ON and the ALL OFF command
(default).
3. It will not respond to ALL ON or ALL OFF commands.
4. It will respond to the ALL OFF command but will not
respond to the ALL ON command.
5. It will respond to the ALL ON command but will not
respond to the ALL OFF command.
Invert Switch
If the switch is accidentally installed upside down with “On”
at the bottom and “Off” at the top, the default On/Off rocker
settings can be reversed by changing parameter 4’s value to
“1”.
• Parameter No: 4
• Length: 1 Byte
• Valid Values = 0 or 1 (default 0)
Dim Rate Adjustments
Both the number of steps (or levels) that the dimmer will
change and the timing of the steps can be modified to suit
personal preferences. The timing of the steps can be adjusted
in 10 millisecond intervals.
1. When Receiving a Z-Wave Dim Command
• Parameter 7 (number of steps or levels)
• Parameter 8 (timing of the steps)
• Length: 1 Byte
• Valid Values:
Parameter 7 (default = 1) Valid Values: 1-99
Parameter 8 (default = 3) Valid Values: 1-255
2. Manual Control Dimming (pressing the Dimmer’s rocker)
• Parameter 9 (number of steps or levels)
• Parameter 10 (timing of the steps)
• Length: 1 Byte
• Valid Values:
Parameter 9 (default = 1) Valid Values: 1-99
Parameter 10 (default = 3) Valid Values: 1-255
3. When Receiving an All-On or All-Off Command
• Parameter 11 (number of steps or levels)
• Parameter 12 (timing of the steps)
• Length: 1 Byte
• Valid Values:
Parameter 11 (default = 1) Valid Values: 1-99
Parameter 12 (default = 3) Valid Values: 1-255
Restoring Factory Defaults
All Configuration Parameters can all be restored to their factory
default settings by using your master controller to delete/reset
the device.
WARRANTY
JASCO Products warrants this product to be free from
manufacturing defects for a period of two years from the original
date of consumer purchase. This warranty is limited to the
repair or replacement of this product only and does not extend to
consequential or incidental damage to other products that may
be used with this product. This warranty is in lieu of all other
warranties, expressed or implied. Some states do not allow
limitations on how long an implied warranty lasts or permit the
exclusion or limitation of incidental or consequential damage, so the
above limitations may not apply to you. This warranty gives you
specific rights, and you may also have other rights which vary from
state to state. Please contact Customer Service at
800-654-8483 (option 4) between 7:30AM – 5:00PM CST or via our
website (www.jascoproducts.com) if the unit should prove defective
within the warranty period,
JASCO Products Company
Building B
10 E Memorial Rd. Oklahoma City, OK 73114
FCC
U2ZZW3007
The Federal Communication Commission Radio Frequency
Interference Statement includes the following paragraph:
The equipment has been tested and found to comply with
the limits for a Class B Digital Device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment uses, generates and
can radiate radio frequency energy and, if not installed and
used in accordance with the instruction, may cause harmful
interference to radio communication. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment
and receiver
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
Operation is subject to the following two conditions:
- This device may not cause interference
- This device must accept any interference, including
interference that may cause undesired operation of the device.
Important Note: To comply with the FCC RF exposure
compliance requirements, no change to the antenna or
the device is permitted. Any change to the antenna or the
device could result in the device exceeding the RF exposure
requirements and void user’s authority to operate the device.
Compliance with IC Rules and Regulations
IC: 6924A-ZW3007
Jasco Products Company
Model: 45716/45717
ZW3007
CAN ICES-3(B) / NMB-3(B)
This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference
that may cause undesired operation of the device.
SPECIFICATIONS
Power: 120 VAC, 60 Hz.
Signal (Frequency): 908.42 MHz.
Maximum Loads: 600W, incandescent
Range: Up to 100 feet line of sight between the Wireless
Controller and the closest Z-Wave receiver module.
Operating Temperature Range: 32-104° F (0-40° C)
For indoor use only.
Specifications subject to change without notice due to
continuing product improvement
Z-Wave is a registered US trademark of Sigma Designs
© 2013 JASCO Products Company
Distributed by Jasco Products Company LLC,
10 E Memorial Rd., Oklahoma City, Oklahoma 73114.
Made in China
Hecho en China
All brand names shown are trademarks of their
respective owners.
Todas las marcas que aparecen aquí son marcas
registradas de sus respectivos dueños.
© 2013 JascoProducts
45716_45717
ZW3007
rev. 07/23/13

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Instance ID                     : uuid:d0421cbe-85bf-6343-a15a-31af464df081
Original Document ID            : adobe:docid:indd:0ace5421-5611-11dc-9b02-aebe626e77a0
Document ID                     : xmp.id:0A80117407206811822A99AE09336DFB
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:0980117407206811822A99AE09336DFB
Derived From Document ID        : xmp.did:0A80117407206811808396F877F802EF
Derived From Original Document ID: adobe:docid:indd:0ace5421-5611-11dc-9b02-aebe626e77a0
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Macintosh)
History Changed                 : /
History When                    : 2013:07:23 16:26:24-05:00
Create Date                     : 2013:07:23 16:26:24-05:00
Modify Date                     : 2013:07:23 16:26:27-05:00
Metadata Date                   : 2013:07:23 16:26:27-05:00
Creator Tool                    : Adobe InDesign CS6 (Macintosh)
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 24
Creator                         : Adobe InDesign CS6 (Macintosh)

EXIF Metadata provided by EXIF.tools