Sheenway Asia ZW3009 In-Wall Capacitive Dimmer User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3463536
Application ID	1C661S7p/IiAP9xFZh3ugg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	411.55kB (5144412 bits)
Date Submitted	2017-07-13 00:00:00
Date Available	2017-07-13 00:00:00
Creation Date	2017-06-30 13:38:47
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2017-06-30 13:55:25
Document Title	User manual
Document Creator	Adobe Illustrator CS6 (Macintosh)

FCC / IC
En
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help
Important note: To comply with the FCC RF exposure compliance requirements, no change to
the antenna or the device is permitted. Any change to the antenna or the device could result in
the device exceeding the RF exposure requirements and void user’s authority to operate the device.
MANUAL • MANUEL • MANUAL
STOP
FCC — U2ZZW3009 | IC: 6924A-ZW3009
Jasco Products Company | Model: ZW3009 / 14316
CAN ICES-3(B) / NMB-3(B)
All brand names shown are trademarks of their
respective owners.
Tous les noms de marque illustrés sont des marques
de commerce de leurs propriétaires respectifs.
Todas las marcas que aparecen aquí
son marcas registradas de sus respectivos dueños.
WARNING
RIESGO DE INCENDIO
RIESGO DE DESCARGA ELÉCTRICA
RIESGO DE QUEMADURAS
CONTROLLING APPLIANCES:
CONTROL DE EQUIPOS
ELECTRODOMÉSTICOS:
AVERTISSEMENT
ATTENTION: POUR RÉDUIRE LE RISQUE DE
SURCHAUFFE ET DE DOMMAGES POSSIBLES À
D’AUTRES APPAREILS, NE PAS INSTALLER POUR
COMMANDER UN APPAREIL ACTIONNÉ PAR MOTEUR,
UN APPAREIL D’ÉCLAIRAGE FLUORESCENT OU UN
APPAREIL ALIMENTÉ PAR UN TRANSFORMATEUR.
• UTILISER SEULEMENT POUR COMMANDER
LES AMPOULES À DEL ET FLUOCOMPACTES À
INCANDESCENCE OU À INTENSITÉ RÉGLABLE
• NE PAS DÉPASSER LES CARACTÉRISTIQUES
NOMINALES
• NE PAS UTILISER POUR COMMANDER DES
APPAREILS POUR LESQUELS UN FONCTIONNEMENT
IMPRÉVU POURRAIT ENTRAÎNER DES CONDITIONS
DANGEREUSES (LAMPE À RAYONS INFRAROUGES,
LAMPE SOLAIRE, ETC.)
• POUR UTILISATION INTÉRIEURE UNIQUEMENT
intelligent
Gradateur
Interruptor de pared
reductor de
luz inteligente
PRECAUCIÓN: A FIN DE DISMINUIR EL RIESGO DE
RECALENTAMIENTO Y DE POSIBLES DAÑOS EN LOS
DEMÁS EQUIPOS, NO INSTALAR PARA CONTROLAR
APARATOS QUE FUNCIONAN A MOTOR, ARTEFACTOS
DE ILUMINACIÓN DE LUZ FLUORESCENTE O
APARATOS ALIMENTADOS CON TRANSFORMADORES.
• USAR EXCLUSIVAMENTE PARA CONTROLAR
BOMBILLAS CFL/LED INCANDESCENTES O
ATENUABLES
• NO SUPERE LOS VALORES NOMINALES ELÉCTRICOS
• NO USAR PARA CONTROLAR DISPOSITIVOS
• USE SOLAMENTE EN INTERIORES
SPECIFICATIONS
ZW3009
Power: 120 VAC, 60 Hz.
Signal (Frequency): 908.4 / 916 MHz
Maximum Loads: 600W, 2-gang 500W or 3-gang 400W incandescent, 150W CFL/LED
Range: Up to 150 feet line of sight between the Wireless Controller and the closest Z-Wave
receiver module.
Operating Temperature Range: 32-104° F (0-40° C)
For indoor use only.
Specifications subject to change without notice due to continuing product improvement
Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED
TO SUPPLY POWER TO, OR CONTROL THE
ON/OFF STATUS OF MEDICAL AND/OR LIFE
SUPPORT EQUIPMENT.
COMMANDE DES APPAREILS:
Montage mural
JASCO Products Company LLC, Building B
10 E. Memorial Rd. Oklahoma City, OK 73114.
NOT FOR USE WITH MEDICAL OR LIFE
SUPPORT EQUIPMENT
RISQUE D’INCENDIE
RISQUE DE CHOC ÉLECTRIQUE
RISQUE DE BRÛLURES
Smart Dimmer
GARANTÍA
JASCO Products garantiza que este producto está libre de defectos de fabricación durante un periodo
de dos años a partir de la fecha original de compra por parte del consumidor. Esta garantía se
limita a la reparación o sustitución de este producto solamente y no se extiende a daños derivados
o accidentales causados a otros productos que se usen con esta unidad. Esa garantía remplaza
a todas las demás garantías expresas o implícitas. Algunos estados no autorizan limitaciones en
cuanto a la duración de una garantía implícita ni permiten la exclusión o limitación por daños
accidentales o derivados; por lo tanto, puede que las anteriores limitaciones no apliquen en su caso.
Esta garantía le da a usted derechos específicos, y otros que usted puede tener y que varían según
el estado en el que usted reside. Si la unidad resultare defectuosa dentro del periodo de garantía,
comuníquese por favor con Atención al Cliente en el 800-654-8483 (opción 1) entre 7 y 20 h, Hora del
Centro, o a través de nuestro sitio de internet (www.byjasco.com).
ADVERTENCIA
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CAUTION: TO REDUCE THE RISK OF OVERHEATING
AND POSSIBLE DAMAGE TO OTHER EQUIPMENT, DO
NOT INSTALL TO CONTROL A RECEPTACLE, A MOTOROPERATED APPLIANCE, A FLUORESCENT LIGHTING
FIXTURE, OR A TRANSFORMER SUPPLIED APPLIANCE.
• ONLY USE TO CONTROL INCANDESCENT OR
DIMMABLE CFL/LED BULBS
• DO NOT EXCEED RATINGS
• DO NOT USE TO CONTROL ANY DEVICE WHERE
UNINTENDED OPERATION COULD CAUSE UNSAFE
CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)
• FOR INDOOR USE ONLY
In-Wall Capacitive Touch
GARANTIE
JASCO Products garantit que ce produit est exempt de tout défaut de fabrication pour une période de
deux ans à compter de la date de l’achat original par l’acheteur. Cette garantie se limite exclusivement
à la réparation ou au remplacement de ce produit et n’est pas applicable aux dommages indirects
ou accessoires survenus sur d’autres produits utilisés avec ce produit. Cette garantie se substitue à
toute autre garantie expresse ou implicite. Certains États ne permettent pas de restrictions quant à
la durée d’une garantie implicite ou permettent l’exclusion ou la limitation des dommages indirects
et accessoires; il se peut, par conséquent, que cette garantie ne s’applique pas dans votre cas. Cette
garantie vous confère des droits juridiques précis; vous pouvez jouir d’autres droits qui peuvent varier
d’un État à l’autre. Veuillez communiquer avec le service à la clientèle au 1-800-654-8483 (option 1)
entre 7 h et 20 h (heure normale du Centre) ou par l’intermédiaire de notre site web (www.byjasco.
com) si l’appareil s’avère défaillant au cours de la période de garantie.
SPÉCIFICATIONS
ZW3009
Tension : 120 VCA, 60 Hz.
Signal (fréquence) : 908.4 / 916 MHz
Charges maximales : 600 watts, 2 compartiments 500 W,
3 compartiments 400 W lampes à incandescent 150W CFL/LED
Portée : Distance à vue entre la télécommande et le module de réception Z-Wave le plus proche
allant jusqu’à 150 pi (45,72m).
Plage de températures de fonctionnement : de 32 à 104 °F (de 0 à 40 °C).
Utilisation intérieure uniquement.
En raison d’améliorations continues du produit, les spécifications peuvent faire l’objet de
changements sans préavis.
NE PAS UTILISER AVEC UN ÉQUIPEMENT
MÉDICAL OU DE SURVIE
LES DISPOSITIFS COMPATIBLES AVEC LA
TECHNOLOGIE Z-WAVE NE DEVRAIENT JAMAIS ÊTRE
UTILISÉS POUR ALIMENTER OU COMMANDER LA MISE
EN MARCHE OU L’ARRÊT DE L’ÉQUIPEMENT MÉDICAL
OU DE SURVIE.
SE PROHÍBE SU EMPLEO EN EQUIPO
MÉDICO O EQUIPO PARA EL
MANTENIMIENTO DE LAS FUNCIONES
VITALES
ESPECIFICACIONES:
ZW3009
Alimentación: 120 VAC, 60 Hz.
Señal (frecuencia): 908.4 / 916 MHz
Cargas máximas: 600 W, Caja para 2 conexiones 500 W,
Caja para 3 conexiones 400 W sólo las lámparas incandescente 150 W CFL/LED
Alcance: Hasta 150 pies (45,72m) en línea de visión directa entre el control remoto inalámbrico y
el módulo receptor Z-Wave más cercano.
Rango de temperatura de funcionamiento: 32-104 °F (0-40 °C).
Para uso en espacios interiores solamente.
Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto.
LOS DISPOSITIVOS Z-WAVE NUNCA SE DEBEN USAR
PARA SUMINISTRAR ENERGÍA ELÉCTRICA AL EQUIPO
MÉDICO O AL EQUIPO PARA EL MANTENIMIENTO DE
FUNCIONES VITALES, NI PARA CONTROLAR EL ESTADO
DE ENCENDIDO O APAGADO DE DICHOS EQUIPOS.
Scan to view
installation guide
Balayez ce code pour
consulter le guide
d’installation.
MADE IN CHINA/FABRIQUÉ EN CHINE/HECHO EN CHINA
GE IS A TRADEMARK OF GENERAL ELECTRIC
COMPANY AND IS UNDER LICENSE BY
JASCO PRODUCTS COMPANY LLC,
10 E. MEMORIAL RD.,
OKLAHOMA CITY, OK 73114.
©JASCO 2016 | 14316 | ZW3009
1.
WARRANTY
JASCO Products warrants this product to be free from manufacturing defects for a period of
two years from the original date of consumer purchase. This warranty is limited to the repair or
replacement of this product only and does not extend to consequential or incidental damage to other
products that may be used with this product. This warranty is in lieu of all other warranties, expressed
or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the
exclusion or limitation of incidental or consequential damage, so the above limitations may not apply
to you. This warranty gives you specific rights, and you may also have other rights which vary from
state to state. Please contact Customer Service at 800-654-8483 (option 1) between 7AM – 8PM CST
or via our website (www.byjasco.com) if the unit should prove defective within the warranty period.
If you have any problems or questions, contact our tech support team at
1-800-654-8483, (option 1) Monday–Friday, 7AM–8PM CST.
For the most up-to-date product support, accessories, electronic (PDF) format
manuals and more, visit www.byjasco.com/support.
• No user serviceable parts in this unit.
Si vous avez des problèmes ou des questions, communiquez avec notre
équipe de soutien technique au 1-800-654-8483, option 1, du lundi au vendredi,
de 7 h à 20 h (HNC).
Pour le soutien relatif aux produits le plus à jour, les accessoires, les manuels en
format électronique (PDF) et plus encore, visitez le site www.byjasco.com/support.
• Aucune des pièces de ce dispositif ne peut être réparée par l’utilisateur.
Si tiene problemas o dudas, comuníquese con nuestro equipo técnico al número:
1-800-654-8483, opción 1 de lunes a viernes, de 7 a.m. a 8 p.m., hora estándar del
centro (CST).
Para recibir el soporte técnico más actualizado sobre productos, accesorios,
manuales en formato digital (PDF), entre otros, visite www.byjasco.com/support.
• Esta unidad no contiene piezas que el usuario pueda reparar.
Fr
Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils
exempts de licence d’Industrie Canada. Son utilisation est sujette aux deux conditions suivantes :
1) cet appareil ne doit pas occasionner de brouillage préjudiciable et 2) cet appareil doit accepter
toutes les interférences reçues, notamment les interférences qui peuvent provoquer un
fonctionnement non désiré.
NOTE DE LA FCC : Le fabricant n’est pas responsable des interférences sur les fréquences
radioélectriques ou télévisuelles pouvant être causées par des modifications non autorisées de ce
matériel. De telles modifications peuvent annuler le droit de l’utilisateur à utiliser cet appareil.
REMARQUE : Cet appareil a été testé et certifié conforme aux limites relatives aux appareils
numériques de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites ont été
définies afin de fournir une protection raisonnable contre le brouillage préjudiciable en milieu
résidentiel. Cet appareil produit, utilise et peut émettre des ondes de fréquence radio et, s’il n’est
pas installé et utilisé conformément aux instructions, il peut provoquer un brouillage préjudiciable
aux communications radio. Il n’existe toutefois aucune garantie que des interférences ne se
produiront pas au sein d’une installation donnée. Si cet appareil occasionne un brouillage
préjudiciable à la réception radiophonique ou télévisuelle, il suffit d’allumer et d’éteindre l’appareil
pour déterminer sa responsabilité. Nous encourageons l’utilisateur à essayer de corriger ces
interférences en appliquant une ou plusieurs des mesures suivantes :
— Réorienter ou déplacer l’antenne de réception.
— Augmenter la distance entre l’appareil et le récepteur.
— Brancher l’appareil à une prise secteur différente de celle du récepteur.
— Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs.
Remarque importante : Pour se conformer aux exigences de conformité de la FCC concernant
l’exposition aux RF, aucune modification apportée à l’antenne ou au dispositif n’est autorisée. Toute
modification apportée à l’antenne ou au dispositif pourrait faire en sorte que le dispositif dépasse
les exigences d’exposition aux RF et pourrait annuler le droit de l’utilisateur à utiliser ce dispositif.
Es
Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC y con
las especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria de Canadá
aplicables a aparatos exentos de licencia. El funcionamiento está sujeto a las siguientes dos
condiciones: (1) este dispositivo no debe provocar interferencia perjudicial, y (2) este dispositivo
debe aceptar toda interferencia que reciba, incluso la que pudiera causar un funcionamiento no
deseado.
NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio o TV
ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas modificaciones
podrían anular la autoridad del usuario para utilizar el equipo.
NOTA: Este equipo ha sido probado y cumple con los límites para aparatos digitales de Clase B,
de conformidad con el apartado 15 de las normas de la FCC. Estos límites están diseñados para
proveer protección razonable contra interferencias perjudiciales en una instalación residencial.
Este equipo genera, usa y puede irradiar energía de radiofrecuencias y, si no se instala y usa según
las instrucciones, puede provocar interferencia perjudicial a las radiocomunicaciones. No obstante,
no hay garantías de que no ocurrirá interferencia en una instalación en particular. Si este equipo
provoca interferencia perjudicial a la recepción de radio o televisión, lo que puede determinarse
encendiendo y apagando el equipo, se recomienda que el usuario intente corregir la
interferencia por medio de la implementación de una o más de las siguientes medidas:
— Reorientar o reubicar la antena receptora.
— Incrementar la separación entre el equipo y el receptor.
— Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que está
conectado el receptor.
— Consultar al distribuidor o a un técnico con experiencia en radio/televisión para
solicitar asistencia.
Nota importante: Para cumplir con los requisitos de cumplimiento de exposición de
radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier cambio a
la antena o dispositivo podría hacer que el dispositivo supere los requerimientos de exposición de
radiofrecuencia y anular la autoridad del usuario para operar el dispositivo.
DO NOT RETURN THIS
PRODUCT TO THE STORE
NE RETOURNEZ PAS
CE PRODUIT AU MAGASIN
NO DEVUELVA ESTE
PRODUCTO A LA TIENDA
Escanear para ver
la guía de instalación
ezzwave.com
Z-Wave® Certified Wireless Lighting Control
Certifié Z-Wave Commande d’éclairage sans fil
Control inalámbrico para iluminación certificado por Z-Wave®
14316
ZW3009
3.
Tools you will need
Out to Light (Load)
Out to
toLight
Light(Load)
(Load)
Out
OR
OR
From Breaker Box
IMPORTANT!
The fixture controlled by the Z-Wave In-Wall Smart Dimmer must not exceed 600
watts (Incandescent); 150W dimmable CFL/LED. The Dimmer is designed only for
use with permanently installed fixtures.
Getting to know your new Z-Wave device
• Turn ON/OFF and adjust dim levels manually or remotely via the Z-Wave controller
• Can be Included in multiple groups and scenes
• May be used in single pole installation or with up to two GE Add-on switches in 3-way
or 4-way wiring configurations
• Compatible with all incandescent and most dimmable CFL/LED bulbs
• Interchangeable paddle switch — white & light almond paddle in package
• Uses a standard, decorative-size wallplate for single gang installations
(wallplate not included)
• Blue LED indicates switch location in a dark room
• Z-Wave Certified for simple pairing and integrated home automation
• Screw Terminal Installation — requires wiring connections for Line (Hot), Load, Neutral,
and Ground. Traveler wire required for 3-way or 4-way installation
• This Z-Wave device has advanced features that allow you to customize your
experience. These features can only be adjusted by a Z-Wave enabled controller that
support the Z-Wave Configuration command class. For a complete list of adjustable
configurations, visit: www.ezzwave.com/config
2.
A. Top Rocker — (Press & release
to turn Dimmer on/off/dim
C.
D.
E.
F.
G.
Ground (Green/Bare)
Load (Black)
Line (Black)
Traveler (Red/Other)
Neutral (White)
From Breaker
Breaker Box
From
Box
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture at the service panel.
All wiring connections must be made with the POWER OFF to avoid personal injury and/or
damage to the switch.
This device is intended for installation in accordance with the National Electric Code and
local regulations in the United States, or the Canadian Electrical Code and local regulations
in Canada. If you are unsure or uncomfortable about performing this installation consult a
qualified electrician.
Multi-switch wiring
For 3-way installations, please refer to Add-on Switch manual
Single switch wiring
Before you start; you may wish to change the paddle color to match your wallplate or
decor. Please proceed to Section 5.
1. Shut off power to the circuit at circuit breaker or fuse box.
IMPORTANT! Verify power is OFF to switch box before continuing.
2. Remove wallplate.
3. Remove the switch mounting screws.
4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.
5. There are up to five screw terminals on the Switch; these are marked
A. LINE (Hot) — Black (connected to power)
5. Insert dimmer into the switch box being careful not to pinch or crush wires.
6. Secure the dimmer to the box using the supplied screws.
7. Mount the wallplate.
8. Reapply power to the circuit at fuse box or circuit breaker and test the system.
Basic Operation
The connected light can be turned ON/OFF and adjust dim levels in two ways:
1. Manually from the front touch panel of the In-Wall Dimmer.
2. Remotely with a Z-Wave Controller.
Manual Control
The Front Touch Panel Dimmer allows the user to:
Turn ON/OFF the connected fixture.
To turn the connected fixture ON: Press and release the top portion of the touch area.
To turn the connected fixture OFF: Press and release the bottom portion of the touch area.
Adjust Dim Levels
To increase brightness: press and release top portion of the touch area.
To decrease brightness: press and release lower portion of the touch area.
B. NEUTRAL — White
C. LOAD — Black (connected to lighting)
D. GROUND — Green/Bare
E. TRAVELER — Red/Other (only in 3-way installations)
Match these screw terminals to the wires connected to the existing switch.
6. Disconnect the wires from the existing switch. Be careful to label wires according to
the previous terminal connection.
Observe Important Wiring Information
IMPORTANT! This switch is rated for and intended to only be used with copper wire.
Wire Gauge Requirements
Use 14 AWG or larger wires suitable for at least 80° C for supplying Line (HOT), Load,
Neutral, Ground and Traveler connections.
Wire strip length:
For attachment to screw terminals: strip insulation 1” (25mm)
For attachment using the enclosure’s holes: strip insulation 5/8” (16mm)
UL specifies that the tightening torque for the screws is 14 Kgf-cm (12 lbf-in).
1. Connect the green or bare copper ground wire to the GROUND terminal.
2. Connect the black wire that goes to the light to the terminal marked LOAD.
3. Connect the black wire that comes from the electrical service panel (Hot) to the
terminal marked LINE.
4. Connect the white wire to the neutral terminal (use a jumper wire if needed).
Note: The Traveler terminal is only used for 3-way or 4-way wiring and should remain
insulated if the switch is being installed in a 2-way system (one switch & one load).
4.
5.
Single, dual and triple gang boxes
When installing the In-wall Smart Dimmer in multiple gang boxes it may be
necessary to break off one or both sides of the scored tabs on the front yoke.
This will affect the electrical rating of the switch (see specifications for details).
To change color of the paddle
2.
1.
Adding your device to a Z-Wave network
1. Follow the instructions for your Z-Wave certified controller to
add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press and
release anywhere on the touch panel.
Now you have complete control to turn your fixture ON/OFF
according to groups, scenes, schedules and interactive
automations programmed by your controller.
If your Z-Wave certified controller features remote access, you
can now control your fixture from your mobile devices.
To remove and reset the device
1. Follow the instructions for your Z-Wave certified controller to
remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press
and hold the side button. Next press and relase anywhere
on the touch panel. Next release side button to remove
device from the network.
To return your switch to factory defaults
1. Press and hold side button. Next press and release
anywhere on touch panel ten (10) times quickly.
Next release side button to reset device.
Note: This should only be used in the event your network’s
primary controller is missing or otherwise inoperable.
This step is optional. Before you start you may
want to change the color of the paddle to
match your wallplate or decor.
1. Lift the air gap tab at the base of the
paddle.
2. Push side tabs in on one side and then
the other to release paddle. Lift the cover
up and off.
3. Simply put the new paddle onto the
switch by inserting the air gap and side
tabs and snapping securely into place.
The GE Add-on switch is required for
Multi-Switch 3-way
or 4-way installations.
Connecting the traveler terminal of this
switch to a standard, non-GE switch
will cause damage or result in improper
function. If this switch is a part of a 3-way
or 4-way multi-switch installation, do not
connect the traveler wire or apply power
until GE Add-on switches are correctly
installed. For more information on 3-Way
or 4-Way installations, view the manual or
quick-start guide that comes with the GE
Add-on switch.
Once this step has been completed please
return to Section 3.
Z-WAVE
INTEROPERABILITY
This product can be included and
operated in any Z-Wave network with
other Z-Wave certified devices from
other manufacturers and/or other
applications. All non-battery operated
nodes within the network will act as
repeaters regardless of vendor to
increase reliability of the network.
This device supports Association Command Class (3 Groups)
• Association Group 1 supports Lifeline, Switch Multi-level report
• Association Group 2 supports Basic Set and is controlled with the local load
• Association Group 3 supports Basic Set and is controlled by pressing the On or Off button
• Each Association Group supports 5 total nodes
NOTE: Actual performance of any CFL or LED will vary from bulb type to bulb type and among
different manufacturers. It is important to note that only bulbs that have been designed as
dimmable should be used on a dimmer. To find out if your bulb is dimmable, please check the
package, the bulb itself, or call the bulb manufacturer directly.
For a complete list of recommended CFL/LED bulbs for this and other Z-Wave products from
Jasco, please vist www.ezzwave.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2017:06:30 13:38:47-05:00
Metadata Date                   : 2017:06:30 13:55:25-05:00
Modify Date                     : 2017:06:30 13:55:25-05:00
Creator Tool                    : Adobe Illustrator CS6 (Macintosh)
Thumbnail Width                 : 184
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 25226 bytes, use -b option to extract)
Instance ID                     : uuid:b67cadb6-8e77-a842-8172-1f4c7ba4fb6c
Original Document ID            : xmp.did:0480117407206811871FC28820FBDC2D
Document ID                     : xmp.did:068011740720681183D18DEDF34D1B6A
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:8a4ab118-8cc0-434e-9c73-324b8bad68c8
Derived From Document ID        : xmp.id:83855f6d-3f31-4ed2-bba9-7d9063bcafed
Derived From Original Document ID: xmp.did:0480117407206811871FC28820FBDC2D
Derived From Rendition Class    : proof:pdf
History Action                  : converted, saved
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Macintosh), Adobe Illustrator CS6 (Macintosh)
History Changed                 : /, /
History When                    : 2016:12:15 15:06:10-06:00, 2017:06:30 13:38:49-05:00
History Instance ID             : xmp.iid:068011740720681183D18DEDF34D1B6A
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
N Pages                         : 1
Has Visible Transparency        : True
Has Visible Overprint           : True
Max Page Size W                 : 15.250000
Max Page Size H                 : 21.250000
Max Page Size Unit              : Inches
Font Name                       : GEInspira, Helvetica-Bold, HelveticaNeue-BoldCond, MyriadPro-Regular, GEInspira-Medium, GEInspira-Bold, GEInspira-ExtraBold, GEInspira-Italic, GEInspira-BoldItalic
Font Family                     : GE Inspira, Helvetica, Helvetica Neue, Myriad Pro, GEInspira Medium, GEInspira Bold, GEInspira ExtraBold, GEInspira Italic, GEInspira BoldItalic
Font Face                       : Regular, Bold, 77 Bold Condensed, Regular, Medium, Bold, ExtraBold, Italic, BoldItalic
Font Type                       : Type 1, TrueType, Type 1, Open Type, Unknown, Unknown, Unknown, Unknown, Unknown
Font Version                    : 002.000, 12.0d1e3, 001.000, Version 2.102;PS 2.000;hotconv 1.0.67;makeotf.lib2.5.33168, Version 2.102;PS 2.000;hotconv 1.0.67;makeotf.lib2.5.33168, Version 2.102;PS 2.000;hotconv 1.0.67;makeotf.lib2.5.33168, Version 2.102;PS 2.000;hotconv 1.0.67;makeotf.lib2.5.33168, Version 2.102;PS 2.000;hotconv 1.0.67;makeotf.lib2.5.33168, Version 2.102;PS 2.000;hotconv 1.0.67;makeotf.lib2.5.33168
Font Composite                  : False, False, False, False, False, False, False, False, False
Font File Name                  : GEIns; GE Inspira, Helvetica.dfont, HelveNeuBolCon; HelveticaNeue HeavyExt, MyriadPro-Regular.otf, MyriadPro-Regular.otf, MyriadPro-Regular.otf, MyriadPro-Regular.otf, MyriadPro-Regular.otf, MyriadPro-Regular.otf
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Groups Group Name        : Default Swatch Group
Swatch Groups Group Type        : 0
Page Count                      : 1
Creator                         : Adobe Illustrator(R) 16.0
For                             : MD,
Title                           : Capacitive Touch Dimmer Draft Manual v2.pdf
Bounding Box                    : 0 0 1098 1530
Container Version               : 11
Creator Version                 : 16
Image Height                    : 1530
Image Width                     : 1098
Image Size                      : 1098x1530
Megapixels                      : 1.7

EXIF Metadata provided by EXIF.tools