Sheenway Asia ZW5303 Remote controller User Manual INTRODUCTION
Sheenway Asia Ltd. Remote controller INTRODUCTION
User manual
45633 Instructions rev 1-a.doc Page 1 of 14 1/13/2010
INTRODUCTION
Thank you for purchasing the GE 45633 Advanced Remote. This remote allows you to control Z-Wave
certified door locks and thermostats as well as up to 18 individual Z-Wave lighting devices. You can also
set up and control up to 18 groups of lights as well as 18 scenes for task or mood lighting. Groups can
include up to 232 Z-Wave devices and each scene can include up to 32 Z-Wave devices. Lights can be
included in multiple groups. Scenes can include lights from different groups. Your Z-Wave home control
network can include up to 232 Z-Wave enabled devices.
Additional features include:
Easy to use LCD menu system
Backlit keypad and LCD
Event programming which allows you to set timed events such as turning on all of your lights at a
certain time every day.
Backlit display with easy to use
menu
Mode Buttons:
Thermostat – Use to check and adjust
system and temperature settings on a Z-
Wave enabled thermostat
LIGHT – Use to program and/or control
individual lights
GROUP - Use to program and/or turn
multiple lights ON or OFF with one button
SCENE – Use to program and/or control
multiple lights at preset brightness levels.
The same light may be included in multiple
scenes.
Menu Selection Buttons:
Use arrow buttons to scroll
between menu items
Press OK to select the displayed
menu item
Setup / Shift Button
Press and hold to enter setup
mode. You can then add lights
to, or delete them from your
control network. You can also
create or modify groups and
scenes, etc.
Press and release to SHIFT
number buttons from 1 - 9 to 10 -
18.
Number Buttons
Use to control up to 18 individual lights, 18
groups and 18 scenes. Press & release to
turn lights on/off. Press & hold to adjust
brightness.
Press the button for numbers 1 – 9; Press
SHIFT, then the button for numbers 10-18
Cancel Button
Press and release to cancel the
current programming operation
All Button
Use to turn ON or OFF all Z-Wave lighting
at the same time. Press ALL and then any
number button
Door Lock Button:
Check lock status and activate
locking mechanism
45633 Instructions rev 1-a.doc Page 2 of 14 1/13/2010
If this remote is used as the primary controller, you must use it to create your control network. You can
use multiple remote controls with your Z-Wave lighting control network, however, only one remote will act
as the primary controller. The primary controller must be used to add or delete devices (lights / nodes)
from your network. All other controllers are considered secondary and can be used to create groups
and/or scenes and control your lighting however secondary controllers cannot add or delete devices from
your network.
NOTE: This product can be operated in one Z-Wave network with Z-Wave certified devices from other
manufacturers and/or other applications. The different listening nodes within the network can act as
repeaters regardless of vendor.
For best results, please read and perform all the remaining instructions before using the remote. Keep
this guide for future reference.
Z-WAVE TERMINOLOGY
Primary Controller: This is the main device used to set up and control your Z-Wave network. There can
only be one primary controller and it must be used to add or delete devices. A primary controller can be a
portable device like a hand-held remote, a static controller (permanently installed & never moved), a Z-
Wave enabled PC or a Z-Wave enabled Ethernet router/bridge.
Secondary Controller: The Z-Wave network supports multiple controllers so the residents can use
additional Z-Wave remotes throughout the home. If the secondary controller is the same brand and
model as the primary, it will have all of the same capabilities as the primary with one exception; the
secondary controller can not be used to add or delete devices.
Slave: Devices within the Z-Wave network are either controllers or slaves. Most AC powered slaves also
function as repeaters in the network, and when required, relay the command signals to the destination
device. Battery powered devices like motion detectors are typically asleep and do not function as
repeaters
Home Control Network: Your controllers and every Z-Wave device you have added with the primary
controller are linked together into a wireless network. Each device in your network has a unique address
assigned to it and cannot be activated by your neighbor’s Z-Wave controller.
Light/Node/Device: Node is the technical term used to describe a Z-Wave device in your home control
network. Please note that the terms “Node”, “Device” and “Light” all refer to an individual Z-Wave
enabled device and are interchangeable within the context of these instructions.
Group: Multiple Z-Wave devices can be turned ON or OFF with a single command when they are placed
into a Group. One example would be grouping your porch light, exterior garage lights and patio lights
together so that they could all be turned ON if you hear a strange sound in the middle of the night.
Scene: A scene lets you establish preset brightness levels for multiple Z-Wave controlled lights and then
control them with one command. This is ideal for mood or task lighting. Scene 1 could be the family
room lights set to dim for watching TV. Scene 2 could have the same lights set to a different brightness
level for other activities like reading or entertaining.
Event: An event is something you want to happen at a specific time and day. This could be everyday, a
specific day of the week, Monday through Friday, Saturday & Sunday only, or a one time occurrence.
Events can be set up to control an individual device, a group or a scene.
Replication: This is the Z-Wave term for copying your lighting control network information to a new
controller.
45633 Instructions rev 1-a.doc Page 3 of 14 1/13/2010
INSTALLING BATTERIES
Three “AAA” Alkaline batteries (not included) are required.
Battery Use and Safety
Use only fresh batteries of the required size and recommended type.
Do not mix old and new batteries or different types of batteries.
If you do not plan to use the remote for an extended period, remove the batteries. They can leak
chemicals that can destroy electronic parts.
Dispose of old batteries promptly and properly. Do not burn or bury them.
To Install Batteries:
1. Open the battery compartment cover (located on the back of the remote).
2. Note the + and - polarity symbols inside the battery compartment.
3. Insert the batteries, making sure their polarity matches the symbols in the compartment.
4. Replace the cover.
! WARNING
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
Controlling Appliances:
Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave
device may be in a different room than the controlled appliance, also an unintentional activation may
occur if the wrong button on the remote is pressed. Z-Wave devices may automatically be powered on
due to timed event programming. Depending upon the appliance, these unattended or unintentional
operations could possibly result in a hazardous condition. For these reasons, we recommend the
following:
1. Assign Z-Wave controlled appliances to device numbers 10 – 18 on the GE remote. The likelihood of
unintentionally turning on the appliance will be reduced significantly because the “Shift” button will
need to be pressed before pressing device numbers 10-18.
2. Z-Wave devices controlling appliances should be removed from “All” control setting. Instructions on
how to do this are included in the manual for your GE remote.
3. Do Not include Z-Wave devices in Groups or Scenes if they control appliances.
4. Do Not use Z-Wave devices to control electric heaters or any other appliances which may present a
hazardous condition due to unattended or unintentional or automatic power on control.
NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT
Z-Wave enabled devices should never be used to supply power to, or control the On/Off status of
medical and/or life support equipment
WIRELESS RANGE
This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 20
meters or approximately 66 feet. Actual performance in a home depends on the number of walls between
the remote controller and the destination device, the type of construction and the number of Z-Wave
enabled devices installed in the control network. Every Z-Wave enabled device acts as a signal repeater
and multiple devices result in more possible transmission routes which helps eliminate “RF dead-spots”.
Things to consider regarding RF range:
Each wall or obstacle (i.e.: refrigerator, big screen TV, etc.) between the remote and the
destination device will reduce the maximum range of 100 feet by approximately 25-30%.
Brick, tile or concrete walls block more of the RF signal than walls made of wooden studs and
plasterboard (drywall).
45633 Instructions rev 1-a.doc Page 4 of 14 1/13/2010
Wall mounted Z-Wave devices installed in metal junction boxes will suffer a significant loss of
range (approximately 20%) since the metal box blocks a large part of the RF signal.
Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices
Note: The distances shown in the table below are typical examples. Actual performance in your home will
vary.
From the Remote (or repeating Z-Wave module) to destination device:
Type of Construction
Wood Frame w/Drywall
Brick, Tile or Concrete
Plastic J-
Boxes*
Metal J-
Boxes
Plastic J-
Boxes*
Metal J-
Boxes
Number of Walls
or Obstacles
0**
100'
80'
100'
80'
1
70'
56'
60'
48'
2
49'
39'
36'
29'
3
34'
27'
21'
17'
* For Plug-in Modules or In-Wall Devices Installed in Plastic Junction Boxes
** Line of Sight / no obstructions
Please Note: Z-Wave home control networks are designed to work properly alongside 802.11 wireless
computer networks, Bluetooth and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video
devices and older cordless phones using the 900MHz frequency range may cause interference and limit
Z-Wave functionality. Many 900MHz products have a switch to select channel “A” or “B”. You may find
that one of these channels will cause less interference than the other.
NOTES ON NETWORK MANAGEMENT
1. Add a node, group or scene can also be referred to as include a node, group or scene.
Remove a node, group or scene can also be referred to as Exclude a node, group or scene.
2. If the screen displays FAILURE during the setup or programming process, you have
pressed an invalid key or the desired action has not been successfully completed Please
try again. Some Z-Wave devices may have to be within two feet of the remote during the
setup process.
ADDING A DEVICE (NODE / LIGHT) TO THE NETWORK
In order to control the lights, they must be Z-Wave enabled and you must first add them to your home
network. There are two ways to do this.
1. Add lights to your remote so that they can be controlled individually using the number keys
(maximum of 18). Adding a device to your remote also adds it to your network. If the device
number you are trying to add is already associated with another device, the previous information
is lost.
2. Add devices to your home network without assigning them to a specific number key. These
devices can only be controlled through the GROUP, SCENE or ALL commands.
To add a device to your home network WITHOUT assigning it to a specific number key:
1. Press and hold SETUP until the screen shows LGHT SETUP
2. Press and Release OK and the screen will display ADD
3. Press OK once; the screen will now display TO NETWORK
4. Press OK and the screen will display SETUP WAITING
5. Press the button on the device so that it communicates with the remote.
45633 Instructions rev 1-a.doc Page 5 of 14 1/13/2010
6. The screen will display SUCCESS to indicate that the Node/Light has been successfully added.
7. The device can now be added to Groups and/or Scenes.
To add a device to your home network and assign it to a specific number key:
1. Press and hold SETUP until screen displays LGHT SETUP
2. Press OK and the screen will display ADD
3. Press OK and the screen will display TO NETWORK
4. Use either Arrow key to scroll until the display reads TO A KEY and then press OK
5. Press a digit (1-9) for the device location you wish to add. Press SETUP (SHIFT) and the digit (1-
9) if you are adding devices 10 through 18.
6. Press OK and the screen will display SETUP WAITING
7. Press the button on the device so that it communicates with the remote.
8. When the screen displays SUCCESS, you have successfully added the device to the number key
and your network.
CONTROLLING INDIVIDUAL LIGHTS (DEVICES / NODES)
You can control a light to turn on or off, or change its brightness level. The operation of a specific device
varies by product. Refer to the manual for that device to learn its specific operation.
1. Press and release the LIGHT key to put the remote into “Individual Light Control” mode. The
remote will stay in this mode until the GROUP, SCENE or ALL mode is activated.
2. Select the light you want to control. (Press and release SHIFT to control lights 10 through 18.)
Turning a Light On or Off:
To turn a light on, press and release the ON key for less than one second. The screen will
display the selected LIGHT/NODE and ON.
To turn a light off, press and release the OFF key for less than one second. The screen will
display the selected LIGHT/NODE and OFF
Setting a Light’s Brightness Level:
To make a light brighter, press and hold the ON key for more than one second. The screen
will display selected LIGHT/NODE and BRT. The light will continue to grow brighter until the
key is released.
To make a light dim, press and hold the OFF key for more than one second. The screen will
display selected LIGHT/NODE and DIM. The light will continue to grow dimmer until the key
is released.
REMOVING AN INDIVIDUAL DEVICE (LIGHT / NODE) FROM YOUR REMOTE
This only removes individual number key control. The device is still part of your home control network
and can be controlled through the GROUP, SCENE and ALL commands.
1. Press and hold SETUP until screen displays LGHT SETUP
2. Press OK followed by either arrow key to scroll until the display reads REMOVE
3. Press OK and the screen will display SEL DIGIT
4. Press a digit (1-9) for the device location you wish to remove. Press SHIFT and the digit (1-9) if
you are removing devices 10 through 18.
5. Press OK and the screen will display SUCCESS
DELETING A DEVICE (LIGHT / NODE) FROM YOUR NETWORK
This completely removes the device from your home control network and resets the device to its factory
default settings.
1. Press and hold SETUP until screen displays LGHT SETUP
2. Press OK followed by pressing the cursor right key 2 times the screen will display DELETE
3. Press OK
4. Press the button on the device so that it communicates with the remote.
5. When the screen displays SUCCESS, you have successfully deleted the node/light from your
network
45633 Instructions rev 1-a.doc Page 6 of 14 1/13/2010
GROUPS
You can create a collection of devices (lights / nodes) that you can control as a group. You can set up a
maximum of 18 groups. A group can contain up to 232 devices.
To create or add a device to a group:
1. Press and hold SETUP until screen displays LGHT SETUP
2. Use either Arrow key to scroll until the display reads GRP SETUP
3. Press the OK key and the screen will display ADD
4. Press OK and the screen will display SEL DIGIT
5. Press a digit (1-9) for the group you wish to add the device to. Press SHIFT and the digit (1-9) if
you are adding a device to groups 10 through 18.
6. Press the OK key and the screen will display SETUP WAITING
7. Press the button on the device so that it communicates with the remote.
8. When the screen displays SUCCESS, you have successfully added the device to your group.
To control a Group:
1. Press GROUP once to put the remote into “GROUP Control” mode. The screen will display
GROUP. The remote will stay in this mode until the Light, Scene or All mode is activated.
2. Press the digit key for the group you wish to control (1-9). Press SHIFT and the digit (1-9) if you
are controlling groups 10 through 18. The screen will display the selected Group.
To turn a GROUP on, press and release the ON key for less than one second. The screen
will display the selected GROUP and ON.
To turn a GROUP OFF, press and release the OFF key for less than one second. The screen
will display the selected GROUP and OFF
Removing a Device (Light / Node) from a Group:
This only removes the device from a specific group. The device is still part of your home control
network and the group still exists (if there were more than one device in it to start).
1. Press and hold SETUP until the screen displays LGHT SETUP
2. Use either Arrow key to scroll until the display reads GRP SETUP
3. Press the OK key followed by the cursor right key once and the screen will display REMOVE
4. Press the OK key and the screen will display SEL DIGIT
5. Press a digit (1-9) for the group you wish to remove the device from. Press SHIFT and the digit
(1-9) if you are removing a device from groups 10 through 18.
6. Press the OK key and the screen will display SETUP WAITING
7. Press the button on the device you wish to remove.
8. When the screen displays SUCCESS, you have successfully removed the device.
Deleting a Group:
This only deletes the specific group. All of the devices are still part of your home control network.
1. Press and hold SETUP until the screen displays LGHT SETUP.
2. Use either Arrow key to scroll until the display reads GRP SETUP
3. Press the OK key, followed by the cursor right key 2 times and the screen will display DELETE
4. The screen will display SEL DIGIT
5. Press a digit (1-9) for the group you wish to delete. Press Shift and the digit (1-9) if you are
deleting groups 10 through 18.
6. Press the OK and the screen will display SUCCESS.
SCENES
A scene is a single device or group of devices that can be preset to turn to a previously specified setting
(for example, brightness level). Scenes are ideal for task or mood lighting. You can set up a maximum of
18 scenes, containing up to 32 devices per scene. Scenes can include lights from different groups.
Adding a Light (Device / Node) to a Scene:
1. Press and hold SETUP until the screen displays LGHT SETUP.
2. Use either Arrow key to scroll until the display reads SCN SETUP
45633 Instructions rev 1-a.doc Page 7 of 14 1/13/2010
3. Press OK and the screen will display ADD
4. Press OK and the screen will display SEL DIGIT
5. Press a digit (1-9) for the scene you wish to add the device to. Press SHIFT and the digit (1-9) if
you are adding devices to scenes 10 through 18.
6. Press OK and the screen will display SETUP WAITING
7. Press the button on the device that you are adding. Adjust the brightness level on the device
within 30 seconds (refer to the manual for the device).
8. When the screen displays SUCCESS, you have successfully added the device to a scene.
To control a scene:
1. Press SCENE once to put the remote in SCENE Mode. The remote will stay in this mode until the
Light, Group or All mode is activated.
2. Press the digit key for the scene you wish to control (1-9). Press SHIFT and the digit (1-9) if you
are controlling scenes 10 through 18. The screen will display scene and the digit selected.
Removing a Light (Device / Node) from a Scene:
This only removes the device from a specific scene. The device is still part of your home control
network and the scene still exists (if there were more than one device in it to start).
1. Press and hold SETUP until screen displays LGHT SETUP
2. Use either Arrow key to scroll until the display reads SCN SETUP
3. Press OK followed by either Arrow key until the display reads REMOVE
4. Press OK and the screen will display SEL DIGIT
5. Press a digit (1-9) for the scene you wish to remove the device from. Press SHIFT and the digit
(1-9) if you are removing devices from scenes 10 through 18.
6. Press the OK key and the screen will display SETUP WAITING
7. Press the button on the device that you wish to remove.
8. When the screen displays SUCCESS, you have successfully removed the device from the scene.
Deleting a Scene:
This only deletes the specific scene. All of the devices are still part of your home control network.
1. Press and hold SETUP until screen displays LGHT SETUP
2. Use either Arrow key to scroll until the display reads SCN SETUP
3. Press OK followed by either Arrow key until the display reads DELETE
4. Press OK and the screen will display SEL DIGIT
5. Press a digit (1-9) for the scene you wish to delete. Press SHIFT and the digit (1-9) if you are
deleting scenes 10 through 18.
6. The screen will display the selected Scene, press the OK key and the screen will display
SUCCESS.
LABELS
Individual LIGHTS, GROUPS and SCENES can all be labeled to help identify their function or location in
your home. The process is the same for all three.
1. Press and hold SETUP until the screen displays LGHT SETUP. Scroll to GROUP or SCENE if
changing those labels.
2. Press OK and the screen will read ADD
3. Use either Arrow key to scroll until the display reads LABEL
4. Press OK and screen will display SEL DIGIT
5. Press a digit (1-9) for the LIGHT, GROUP or SCENE you wish to rename. Press SHIFT and the
digit (1-9) if you are re-naming 10 through 18.
6. The screen will display the selected LIGHT, GROUP or SCENE
7. Use the #1 On/Off key to scroll through the alphabet/numbers until you reach the appropriate
letter or number
8. Use the right Arrow key to move to the next letter and repeat step 7
9. Continue this process until your new label is complete
10. Press the OK key and the screen will display SUCCESS.
ALL-ON and ALL-OFF Control
45633 Instructions rev 1-a.doc Page 8 of 14 1/13/2010
The factory default setting for GE Z-Wave lighting control devices is to be included in All-On and All-Off
control. Other brands of Z-Wave enabled lighting control devices may have to be manually added to All
control. If desired, specific devices can also be setup to ignore the All-On and All-Off commands.
To turn all devices on or off, perform the following steps:
1. Press ALL once. The screen will display ALL
2. Press either ON or OFF. Any ON or OFF button can be pressed. (The screen will display ALL ON
or ALL OFF depending on what key was pressed)
Adding Devices (Lights / Nodes) to All Control:
1. Press and hold SETUP the screen displays LGHT SETUP.
2. Use either Arrow key to scroll until the display reads ALL SETUP
3. Press OK and screen will display EX ON/OFF
4. Use either Arrow key to scroll until the display reads INC ON/OFF
5. Press OK and the screen will display SETUP WAITING
6. Press the button on the device that you wish to add to All Control.
7. The screen will display SUCCESS
Deleting Devices (Lights / Nodes) from All Control:
1. Press and hold SETUP until the screen displays LGHT SETUP.
2. Use either Arrow key to scroll until the display reads ALL SETUP
3. Press OK and screen will display EX ON/OFF
4. Press OK and the screen will display SETUP WAITING
5. Press the button on the device that you wish to remove from All Control.
6. The screen will display SUCCESS
TIME AND DATE SETUP
Setting the Time:
1. Press and hold SETUP until the screen displays LGHT SETUP
2. Use either Arrow key to scroll until the display reads DATE/TIME
3. Press OK and the screen will display TIME
4. Press OK and the screen will display TIME 12hr
5. Pressing ON or OFF with the 1 key will adjust the hour.
7. Pressing ON or OFF with the 2 key will adjust the minutes
8. Pressing ON or OFF with the 3 key will toggle between AM and PM
9. Once you have setup the correct Time, press the OK key and screen will read SUCCESS.
Setting the Date:
1. Press and hold SETUP until the screen displays LGHT SETUP
2. Use either Arrow key to scroll until the display reads DATE/TIME
3. Press OK and the screen will display TIME
4. Use either Arrow key to scroll until the display reads DATE
5. Press OK and the screen will display default date of 01/01/2007
6. Pressing ON or OFF with the 1 key will adjust the Month.
1. Pressing ON or OFF with the 2 key will adjust the Day
2. Pressing ON or OFF with the 3 key will toggle between Year
3. Once you have setup the correct Time, press the OK key and screen will read SUCCESS.
NOTE: You will need to reprogram the Time, Date and Day if the batteries are removed for more
than three minutes.
EVENTS
The GE 45633 Advanced Remote allows you to program up to 9 automated events such as turning on or
off your lights at a preset time and day. You must set the time, date and day before programming an
Event.
Adding an EVENT:
45633 Instructions rev 1-a.doc Page 9 of 14 1/13/2010
1. Press and hold SETUP until the screen displays LGHT SETUP
2. Use either Arrow key to scroll until the display reads EVENTS
3. Press OK and the Screen will display ADD
4. Press OK and the Screen will display EVERY DAY. Use Either Arrow key to change this option
to MON-FRI, SAT-SUN, ONE TIME or a specific Day of the WEEK,
5. Once you have chosen the Event profile, press the OK key
6. The Screen will now display SEL DIGIT
7. Press any digit and the screen will display the EVENT number
8. Press and release OK and the screen will display ENABLED
9. PRESS OK and the Screen will display EVENT TYPE
10. Use either arrow key to scroll between the LIGHT, SCENE and GROUP options (Pressing
DIGITS 1-9 will adjust the LIGHT number accordingly).
11. After you select the EVENT type, press the OK key and the screen will display ON TIME
12. Pressing ON or OFF with the 1 key will adjust the hour.
10. Pressing ON or OFF with the 2 key will adjust the minutes
11. Pressing ON or OFF with the 3 key will toggle between AM and PM
13. Press the OK key once you have programmed the ON TIME and the screen will display OFF
TIME
14. Pressing ON or OFF with the 1 key will adjust the hour.
12. Pressing ON or OFF with the 2 key will adjust the minutes
13. Pressing ON or OFF with the 3 key will toggle between AM and PM
15. Once you have programmed the OFF time press OK and the screen will display SUCCESS.
Random EVENTS:
The GE 45633 Advanced Remote allows you to program automated events such as turning on or off your
lights at a predetermined time and day. By choosing the RANDOM option, the EVENT will start at +/-15
minutes of the Scheduled Time.
To activate this function, after step 8 above, use either arrow key to scroll until the display reads
RANDOM. Press OK and the Screen will display EVENT TYPE. Continue the programming as shown in
step 10 above.
Disabling an EVENT:
Once an event has been programmed, it can be disabled by following steps 1-8 above and then scrolling
to DISABLED and pressing OK.
Deleting an EVENT:
1. Press and hold SETUP until the screen displays LGHT SETUP
2. Use either Arrow key to scroll until the display reads EVENT
3. Press OK and the Screen will display ADD
4. Use either arrow key to scroll until the screen displays DELETE
5. Press OK and the Screen will display SEL DIGIT
6. Press the DIGIT for the EVENT you want to DELETE
7. Press OK and the screen will display SUCCESS.
DOOR LOCKS:
The GE 45633 Advanced Remote allows you to program and control up to 6 Z-Wave certified door locks.
These can be assigned to number keys 1 – 6.
Adding a Door Lock:
1. Press and hold SETUP until screen displays LGHT SETUP
2. Use either arrow key to scroll until the screen displays LOCK
3. Press OK and the screen will display ADD
4. Press OK and the screen will display SEL NUMBER
5. Press a number key (1 – 6) and the screen will display SETUP WAITING
6. Enter the proper code on the lock’s Z-Wave interface*
45633 Instructions rev 1-a.doc Page 10 of 14 1/13/2010
7. When the screen displays SUCCESS, you have successfully added the Door Lock to your control
network.
* The setup process for door locks varies by lock manufacturer. Please refer to your lock’s
documentation for detailed instructions.
Controlling a Door Lock:
1. Press the LOCK button on the remote to enter that mode.
2. Press the number key associated with the lock you want to control
3. The screen will change to display “Lock X” and a small icon will appear in the lower right corner.
a. The icon indicates the lock’s current status; locked or unlocked
4. Press the top of the number button to lock the door lock or the bottom of the button to unlock the
door lock. Please note that actual operation of the door lock varies by manufacturer. Some
brands activate the mechanism to allow manual operation of the deadbolt while others extend or
retract the deadbolt.
Deleting a Door Lock:
1. Press and hold SETUP until screen displays LGHT SETUP
2. Use either arrow key to scroll until the screen displays LOCK
3. Press OK and the screen will display ADD
4. Scroll to DELETE and press OK
5. The screen will display SEL NUMBER
6. Press a number key (1 – 6) and the screen will display SETUP WAITING
7. Enter the proper code on the lock’s Z-Wave interface*
8. When the screen displays SUCCESS, you have successfully deleted the Door Lock from your
control network.
* The setup process for door locks varies by lock manufacturer. Please refer to your lock’s
documentation for detailed instructions.
THERMOSTATS
The GE 45633 Advanced Remote allows you to program and control a Z-WAVE enabled Thermostat.
Adding a Thermostat:
1. Press and hold SETUP until screen displays LGHT SETUP
2. Use either arrow key to scroll until the screen displays THERMOSTAT
3. Press OK and the screen will display ADD
4. Press OK and the screen will display SETUP WAITING
5. Press the button on the thermostat’s Z-Wave interface
6. When the screen displays SUCCESS, you have successfully added the THERMOSTAT to your
remote control.
Controlling a Thermostat:
The features and functions that can be controlled vary by manufacturer and you will need to review the
user manual that was provided to determine capabilities of your thermostat. If supported by the
thermostat, the 45633 Advanced Remote allows you to check room temperature, adjust HVAC system
modes (Heat, Cool, Auto, Fan, etc.) and adjust temperature settings (setpoints). Please note that your
HVAC system may have to be set to “HEAT or “COOL’” mode in order to remotely check and/or adjust the
room temperature.
Deleting a Thermostat:
1. Press and hold SETUP until screen displays LGHT SETUP
2. Use either arrow key to scroll until the screen displays THERMOSTAT
3. Press OK and the screen will display ADD
4. Use either arrow key to scroll until the screen displays DELETE
5. Press OK and the screen will display SETUP WAITING
6. Press the button on the thermostat’s Z-Wave interface*
45633 Instructions rev 1-a.doc Page 11 of 14 1/13/2010
7. When the screen displays SUCCESS, you have successfully deleted the thermostat.
* Refer to the thermostat’s instructions for detailed instructions.
ADVANCED CONFIGURATION
Some Z-Wave devices provide advanced capabilities available only through the use of a remote control
like the GE 45633 Advanced Remote. One example is the GE 45606 in-wall dimmer which allows the
end user to create 3 different dim rates depending upon how the dimmer is activated (manually, via a
normal Z-Wave “Dim” command or via an All-On or All-Off Z-Wave command). Each of the three can be
set anywhere between 10 milliseconds and 4.2 minutes for the time it takes to go from full intensity to
minimum intensity.
Please refer to the instructions of your Z-Wave device for available options and specific instructions on
changing its advanced configuration.
To Change Advanced Configuration Settings:
1. Press and hold SETUP the screen displays LGHT SETUP.
2. Use either Arrow key to scroll until the display reads ADV CONFIG
3. Press OK and screen will display PARAM 0
4. Use either Arrow key to scroll until the display reads the proper parameter number (1 - 255) as
indicated in the Z-Wave device’s instructions
5. Press OK and the screen will read NUM BYTES
6. Use either Arrow key to scroll until the display reads the proper number of bytes (1, 2 or 4) as
indicated in the Z-Wave device’s instructions
7. Press OK and the screen will display read CONFIG VAL
8. Use either Arrow key to scroll until the display reads the proper value (0 - 255) as indicated in the
Z-Wave device’s instructions
9. Press OK
10. Press the button on the device.
11. The screen will display SUCCESS
CREATE SECONDARY CONTROLLER
SENDING DEVICE AND NETWORK INFORMATION TO A SECONDARY REMOTE
You can add a secondary remote to your network, and copy your primary remote’s device and network
information to it.
To send device and network information to a secondary remote:
1. Place the two remotes near each other.
2. Press and hold SETUP on the primary GE 45633 ADVANCED remote until the display reads
LGHT SETUP.
3. Use either Arrow key to scroll until the display reads TRANSFER
4. Press OK and the screen will display PRIMARY
5. Use either arrow key to scroll until the display reads SECONDARY
6. Press and OK and the Screen will display ALL
7. Refer to the user manual for the secondary remote for programming information. See the
following section on “Copying Network/Device Information” if the target remote is a GE 45633
remote. Put the target (secondary) remote into programming mode so that communicates with
the primary remote. The primary remote then copies the network and device information to the
new secondary remote.
8. Press the OK key and the screen will display SENDING.
9. When screen displays SUCCESS you have successfully transferred the information.
10. Add devices, groups, and scenes to the new secondary remote as needed.
SENDING INFORMATION TO A SECONDARY REMOTE
You can add a secondary remote to your network, and copy your primary remote’s network and device
information to it.
To send information to a secondary remote:
45633 Instructions rev 1-a.doc Page 12 of 14 1/13/2010
1. Place the two remotes near each other.
2. Press and hold SETUP on the primary 45633 ADVANCED remote until the display reads LGHT
SETUP.
3. Use either Arrow key to scroll until the display reads TRANSFER
4. Press OK and the screen will display PRIMARY
5. Use either arrow key to scroll until the display reads SECONDARY
6. Press OK and the Screen will display ALL
a. To send network and device information to the new remote, proceed to Step 7.
b. To send only network information to the new remote, use either arrow key to scroll to
NTWK ONLY and proceed to Step 7.
7. Refer to the user manual for the secondary remote for programming information. Put the target
(secondary) remote into programming mode so that it receives information from the primary
remote. See the following section on “Copying Information to this Remote” if the target remote is
a 45633 remote.
8. Press the OK key and the screen will display SENDING.
9. When screen displays SUCCESS you have successfully transferred the information.
Copying Information to this Remote
1. Place the two remotes near each other.
2. Refer to the user manual for the primary remote for programming information. Put the primary
remote into programming mode so that it sends information to the secondary remote. If the
primary remote is a 45633 Advanced Remote, refer to the section above on Sending Network
Information.
3. On the target 45633, use either Arrow key to scroll until the display reads TRANSFER
4. Press OK and the screen will display PRIMARY
5. Use either arrow key to scroll until the display reads RECEIVE
6. Press OK and the Screen will display RECEIVING
7. When screen displays SUCCESS you have successfully transferred the information.
PRIMARY CONTROLLER SHIFT (TRANSFER)
You can transfer all of the 45633’s information to another remote, so it becomes the new primary
controller. The 45633 will retain all of its programming; however, it will now be a secondary controller.
Transferring Primary Controller Information:
1. Place the two remotes near each other.
2. On the 45633, press and hold SETUP until the screen displays LGHT SETUP.
3. Use either Arrow key to scroll until the display reads TRANSFER
4. Press OK and the display will read PRIMARY
5. Press OK and the display will read ALL
a. To send network and device information to the new remote, proceed to Step 6.
b. To send only network information to the new remote, use either arrow key to scroll to
NTWK ONLY and proceed to Step 6.
6. Put the target (new primary) remote into programming mode so that it receives information from
the 45633.
7. On the 45633, press the OK key and the display will read SENDING
8. When the screen displays SUCCESS, you have successfully transmitted the information to the
new primary controller.
RESETTING YOUR NETWORK
You can reset your network to clear all device and Z-Wave network information from the remote. This
does not reset the Z-Wave devices to their factory default. Each device still needs to be deleted in order
to reset them. Please refer to the section on “Deleting a Device from Your Network” for details
45633 Instructions rev 1-a.doc Page 13 of 14 1/13/2010
To reset your network:
1. Press and hold SETUP until the screen displays LGHT SETUP
2. Use either Arrow key to scroll until the display reads NETWORK
3. Press OK and the screen will display RESET
4. Press OK and the screen will display RESETTING
5. When the screen displays SUCCESS, you have successfully reset network information.
6. Reset all individual devices as instructed in the section on deleting devices from the network
RECOVERING NETWORK INFORMATION
This is typically used to rebuild the routing tables when a lighting device has been moved from its original
location. The controller must be primary to initiate a network recovery.
To have your remote recover network information:
1. Press and hold SETUP until the screen displays LGHT SETUP
2. Use either Arrow key to scroll until the display reads NETWORK
3. Press OK and the screen will display RESET
4. Use either Arrow key to scroll until the display reads RECOVERY
5. Press OK and the screen will display SEL NODE
6. Press the ALL Key and the screen will display SETUP WAITING
7. When the screen displays SUCCESS. You have successfully recovered network information.
Functional Overview
This device is based on the Z-Wave Controller Library and the Remote Controller Generic Device Class.
It controls devices that support the following Z-Wave Command Classes:
• Basic Command Class
• Binary Switch Command Class
• Configuration Command Class
• Controller Replication Command Class
• Encryption Command Class
• Lock Command Class
• Manufacturer Specific Command Class
• Multi-level Switch Version 1 Command Class
• Thermostat Command Class
• Version Command Class
When using the Basic Command Class to control devices the controller will either transmit a value of 0 or
255, depending on the button pressed.
Keeping the controller awake:
Under normal circumstances, the controller goes into stand-by mode (sleep) after approximately10
seconds of inactivity (no button presses) in order to extend battery life.
It may be desirable to keep the controller awake for longer time periods so that another controller can
request Version or Manufacturer Specific information. Press and hold any button that is associated with a
device to keep the controller awake for the desired time period.
Interoperability with Z-Wave™ Devices
A Z-Wave™ network can integrate devices of various classes, and these devices can be made by
different manufacturers. Although every Z-Wave certified product is designed to work with all other Z-
Wave certified products, your controller must include the appropriate device classifications in order to
control non-lighting Z-wave devices. As an example, the GE 45600 basic remote is designed only for
controlling Z-Wave devices using the lighting control classification. The GE 45633 deluxe remote with
LCD readout can control other Z-Wave certified devices like thermostats as well as lighting.
45633 Instructions rev 1-a.doc Page 14 of 14 1/13/2010
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off or on, the user should:
• Relocate or reorient the TV or radio antenna
• Increase the separation between the device and the receiver.
Any changes or modifications to the equipment without JASCO’s express consent will void the user’s right
to operate this equipment.
FCC ID: xxxxxxxxxx
Compliance with IC Rules and Regulations
IC: xxxxxxxxxxxx
Jasco Products Company
Model: 45633 / ZW5303
Object is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation
of the device."
WARRANTY
JASCO Products warrants this product to be free from manufacturing defects for a period of two years
from the original date of consumer purchase. This warranty is limited to the repair or replacement of this
product only and does not extend to consequential or incidental damage to other products that may be
used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states
do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of
incidental or consequential damage, so the above limitations may not apply to you. This warranty gives
you specific rights, and you may also have other rights which vary from state to state. Please contact
Customer Service at 800-654-8483 (option 4) between 7:30AM – 5:00PM CST or via our website
(www.jascoproducts.com) if the unit should prove defective within the warranty period,
JASCO Products Company
Building B
10 E Memorial Rd.
Oklahoma City, OK 73114
The GE logo is a trademark of the General Electric Company and is used under license to
Jasco Products Company LLC.
Made in China
© JASCO Products, 2010
Z-Wave is a registered US trademark of Sigma Designs