Shen Zhen RDM Tag Master M28 AFC READER User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1294814
Application ID	9lU+K6xsHCpX4ls4TjIbqw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	27.19kB (339931 bits)
Date Submitted	2010-06-11 00:00:00
Date Available	2010-06-11 00:00:00
Creation Date	2007-04-13 17:16:33
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2010-05-24 13:11:31
Document Title	untitled

RDM TAG MASTER CO.,LTD
M28 SERIAL MODULE:
OEM & ODM ISO14443A/B, ISO15693, ISO11784/11785 MODULE
DEVELOPMENT KIT
RS232 or SPI OPERATIONS
The OEM & ODM ISO14443-A-B, ISO15693, ISO11784 /11785 MODULE can operate with a
terminal such as computer or other controller, which can supply RS232 or SPI interface.
1.1
Electrical Interface
Basically, this communication protocol does not need to be bound with any electrical interface
characteristic. Typically the following types of physical link could be used:
1.2
•
RS232 (Point to point only)
•
CMOS-Logic Level (Point to point only)
•
SPI (Slave only)
Data Format
The data format (Start Bit, Data Bits, parity, Stop Bit) is software configurable, and can be set to
match the special requirement of data transmission between two communication devices. The
general data format is defined as:
Parameter
Description
Baud Rate
Selective: 9600, 19200, 38400, 57600, 1152000
(It can be changed by command Send from the Host)
Data Bits
Fixed: 8 bits
Start Bit
Fixed: 1 Bits
Stop Bit
Selective: 1 bit.
Parity
None
The following is the default setting (RS232):
Baud Rate
Data Bits
Start Bit
Stop Bit
Parity
9600
None
中国 ·深圳市南山区高新区科技南十二路方大大厦 201 室
TEL： +86-755- 61313350
th
Fangda Building201,Keji 12 Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China
Http://www.datarfid.com
E-mail：support@datarfid.com
FAX：+86-755- 61313357
RDM TAG MASTER CO.,LTD
Link Layer
The communication protocol is a packet-oriented protocol - all the data exchanged between two
communication devices will be based on packet format. The protocol is designed for multi-drop
mode and where point-to-point mode could be treated as a special case of multi-drop mode.
The data packet starts with the control character ‘STX’ and ends with ‘ETX’, which follows the 8-bit
BCC checksum. Besides the checksum is used for error checking, character (byte) time-out and
packet (command) time-out are used to re-synchronous the communication.
2.1
Packet Format
There are two types of data packets. Command Message is the packet Send from the Host to the
reader device. The Reply Message is the packet Send from the reader to the Host.
Packet format for Command Message (Host to Reader)
STX
STATION ID
DATA LENGTH
CMD
DATA[0..N]
BCC
ETX
Packet format for Reply Message (Reader to Host)
STX
STATION ID
DATA LENGTH
STATUS
中国 ·深圳市南山区高新区科技南十二路方大大厦 201 室
DATA[0..N]
BCC
TEL： +86-755- 61313350
th
Fangda Building201,Keji 12 Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China
Http://www.datarfid.com
E-mail：support@datarfid.com
FAX：+86-755- 61313357
ETX
RDM TAG MASTER CO.,LTD
Available Commands
Name
Description
SYSTEM COMMANDS
SetAddress
Program the Device Address to the reader
SetBaudrate
Set the reader’s communication baud rate
SetSerlNum
Set the reader’s Serial Number
GetSerNum
Get the reader’s Serial Number
SetUserInfo
Set the Usr Information
GetUserInfo
Get the User Information
GetVerNum
Get the reader’s firmware version number.
SetPort
Control status of the I/O ports.
SetLED
Turn On/Off the LEDs
SetBuzzer
Turn On/Off the Buzzer
Control-workmode
Control the reader to stay in active state or idle state
ISO14443-A-B COMMANDS
REQA
ISO14443A REQUEST
Anticoll
ISO14443A Anti-collision
Select
ISO14443A Select
Halt
ISO14443A Halt
Request_B
ISO14443B REQB command
Attrib_B
ISO14443B ATTRIB command
RDM_Rst_ Typeb
Integrate the request and attrib command
RDM__Typeb_Trans
fer_Command
ISO14443-4 transparent command Type B Card
MF_Read
The Read command integrates the low level commands (request, anticollision, select, authentication, read) to achieve the reading operation
with a one-step single command.
MF_Write
The Write command integrates the low level commands (request, anticollision, select, authentication, write) to achieve the writing operation
中国 ·深圳市南山区高新区科技南十二路方大大厦 201 室
TEL： +86-755- 61313350
th
Fangda Building201,Keji 12 Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China
Http://www.datarfid.com
E-mail：support@datarfid.com
FAX：+86-755- 61313357
RDM TAG MASTER CO.,LTD
with a one-step single command.
MF_InitVal
The Initialization command integrates the low level commands (request,
anti-collision, select, authentication) to achieve the value block
initialization with a one-step single command.
MF_Decrement
The Decrement command integrates the low level commands (request,
anti-collision, select, authentication) to achieve the Decrement with a
one-step single command.
MF_HLIncrement
The Increment command integrates the low level commands (request,
anti-collision, select, authentication) to achieve the Increment with a
one-step single command.
MF_GetSnr
The GetSnr command integrates the low level commands
(request,anticoll,select) to achieve the select card with a one-step single
command,and output the card’s Snr
ISO15693 COMMANDS
RDM_Inventory
ISO15693 Inventory Command
RDM_Read
ISO15693 Read Command
RDM_Write
ISO15693 Write Command
RDM_Lockblock
ISO15693 Lock_Block Command
RDM_StayQuiet
ISO15693 Stay_Quiet Command
RDM_Select
ISO15693_Select Command
RDM_Resetready
ISO15693_Reset_To_Ready Command
RDM_Write_Afi
ISO15693_Write_AFI Command
RDM_Lock_Afi
ISO15693_Lock_AFI Command
RDM_Write_Dsfid
ISO15693_Write_DSFID Command
RDM_Lock_Dsfid
ISO15693_Lock_DSFID Command
RDM_Get_Information
ISO15693_Get_System_Information Command
RDM_Get_Multiple_Block_Security ISO15693_Get_Multiple_Block_Security Command
中国 ·深圳市南山区高新区科技南十二路方大大厦 201 室
TEL： +86-755- 61313350
th
Fangda Building201,Keji 12 Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China
Http://www.datarfid.com
E-mail：support@datarfid.com
FAX：+86-755- 61313357
RDM TAG MASTER CO.,LTD
RDM_15693_Transfer_Command
Using this command may transparent ISO15693
command to The Card that it meet the ISO15693 protocol
CAUTION: Changes or Modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
3.1
3.1.1
Sequence Example
SetBaudrate ( 0x81 )
Data Field
DATA[0]
Communication speed
0x00 – 9600 bps
0x01 – 19200 bps
0x02 – 38400 bps
0x03 – 57600 bps
0x04 – 115200 bps
Response:
STATUS:
0x00 - OK
Data Field
DATA[0]
Return the new communication speed Code.
0x00 – 9600 bps
0x01 – 19200 bps
0x02 – 38400 bps
0x03 – 57600 bps
0x04 – 115200 bps
Description
Set the reader’s baud rate for host communication. The baud rate will be stored in the reader’s
EEPROM and used as the new default baud rate.The new baud rate will not take effect until the
reader is reset.
EXAMPLE:
Send Data： AA 02 02 81 01 80 BB
Response Data：： AA 02 02 00 01 01 BB (19200,N,8,1)
3.1.2
CMD_MF_Request (0x25)
Data Field
DATA[0]:
Request mode
0x00 – Request Idle
0x01 – Request All
DATA[1]:
00 don’t need to execute the halt command
中国 ·深圳市南山区高新区科技南十二路方大大厦 201 室
TEL： +86-755- 61313350
th
Fangda Building201,Keji 12 Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China
Http://www.datarfid.com
E-mail：support@datarfid.com
FAX：+86-755- 61313357
RDM TAG MASTER CO.,LTD
01 need to execute the halt command
Response:
Data Field
STATUS:
0x00 – OK
DATA[0-3]:
Card Serial Number
Description:
The High Level Value Increment Command integrates the low level commands (Request, AntiColl1,
Select) and get the SNR of selected card.
EXAMPLE:
Send Data：
aa 02 03 25 26 00 02 bb
Response Data：AA 02 06 00 00 16 0F F4 7F 96 BB
3.2
3.2.1
ISO15693 Commands Example
RDM_Inventory (0x10)
Data Field
DATA[0]:
Flags
Bit0: Sub_carrier_flag
Bit1: Date_rate_flag
Bit2: Inventory_flag
Bit3: Protocol Extension_flag
Bit4: Afi_flag
Bit5: nb_slots_flag
Bit6: Option_flag
Bit7: RFU
DATA[1]:
Afi
DATA[2]:
Masklengh
DATA[3..10]:
Maskvalue
Response:
STATUS:
0x00 - OK
Data[0] :
The card’s number that exist in the reading area
Data[1..n] :
UID
Description:
Run the anticollison loop. through this command you can get the UID of all the VICC in the readable
zone.(usually it may get 3 to 6 card’s snr,it base on the strength of the RF power)
Example:
Send Data：
aa 00 04 10 06 00 00 12 bb
中国 ·深圳市南山区高新区科技南十二路方大大厦 201 室
TEL： +86-755- 61313350
th
Fangda Building201,Keji 12 Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China
Http://www.datarfid.com
E-mail：support@datarfid.com
FAX：+86-755- 61313357
RDM TAG MASTER CO.,LTD
When only one card in the reading area：
Two card in the reading area：
AA 00 0B 00 01 00 01 4A 80 E9 11 00 00 07 3E BB
AA 00 15 00 02 00 01 4A 80 E9 11 00 00 07 E0 00 00
3B 80 E9 11 00 00 07 87 BB
Three card in the reading area：
AA 00 1F 00 03 00 01 4A 80 E9 11 00 00 07 E0 00 00
3B 80 E9 11 00 00 07 E0 00 00 3F 80 E9 11 00 00 07 2C BB
Four card：
AA 00 29 00 04 00 01 4A 80 E9 11 00 00 07 E0 00 00
3B 80 E9 11 00 00 07 E0 00 00 3E 80 E9 11 00 00 07 E0 00 00 3F 80 E9 11 00 00 07 BC BB
Have no card in the reading area：
AA 00 02 01 83 80 BB
中国 ·深圳市南山区高新区科技南十二路方大大厦 201 室
TEL： +86-755- 61313350
th
Fangda Building201,Keji 12 Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China
Http://www.datarfid.com
E-mail：support@datarfid.com
FAX：+86-755- 61313357
RDM TAG MASTER CO.,LTD
note:
the FCC ID will placed on a label on the outside of the host enclosure after integration.
“Contains FCC ID: U7NM28.”
Antenna information:
Antenna Manufacturer: Wuxi Sunsky Technology co.，LTD
Antenna Model Number: WX-09-7026B
Antenna Connector Type: SMA plug reverse connector
Antenna Connector Model Number: 7026C
Antenna coax cable loss:0.1dB
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
there are very strict operational and timing requirements that must be met
before a transmitter is authorized for operation under Section 15.225. For instance, data
transmission is prohibited, except for operation under Section 15.225, in which case
there are separate field strength level and timing requirements. Compliance with these
requirements must be assured.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Information in this document is subject to change without notice. No part of this document may be
reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without
the express written permission of RDM Tag Master Co.,Ltd.
中国 ·深圳市南山区高新区科技南十二路方大大厦 201 室
TEL： +86-755- 61313350
th
Fangda Building201,Keji 12 Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China
Http://www.datarfid.com
E-mail：support@datarfid.com
FAX：+86-755- 61313357

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : 3.1-702
About                           : uuid:57d9181e-de5d-4f43-9b46-2a3cb05828f5
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2007:04:13 17:16:33+08:00
Modify Date                     : 2010:05:24 13:11:31-04:00
Metadata Date                   : 2010:05:24 13:11:31-04:00
Document ID                     : uuid:a90abb14-8c34-467c-a22e-ef77c94abc6f
Instance ID                     : uuid:93faa404-7bf9-4217-b0ff-4a04cdbd2b73
Format                          : application/pdf
Title                           : untitled
Has XFA                         : No
Page Count                      : 8

EXIF Metadata provided by EXIF.tools