Shen Zhen WFLY Technology Development WFT09 Radio Control Transmitter User Manual manual

Download:
Mirror Download [FCC.gov]
Document ID	796364
Application ID	JDUhCe6qheP80YkwL/bSsA==
Document Description	Users Manual II
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	205.25kB (2565570 bits)
Date Submitted	2007-05-24 00:00:00
Date Available	2007-05-24 00:00:00
Creation Date	2007-05-24 11:43:24
Producing Software	Corel PDF Engine Version 1.0.0.525
Document Lastmod	2007-05-24 11:43:41
Document Title	备份manual
Document Creator	CorelDRAW 12.0 版

WFT09
INSTRUCTION
15. TIMER
This function is to control two electronic clocks used to keep
track of time remaining in a competition time allowed, flying time
on a tank of fuel, amount of time on a battery, etc.
Setting Method
Use up or down button to select TIMER , OK button is to enter
editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button for proper adjustment,
3. Press EXIT after setting.
16. More setting
(1). GYRO sens setting
A good gyro will totally eliminate the need for revo.mixing.
The gyro wil sense and correct the unwanted motion for you,
so you don’t have to spend time to get a complex curve operating
properly. It simplifies adjusting/selecting the gyro sensitivity,
and can provide more than 2 gyro gain settings. (The higher the
gain, the more correction the gyro provides and the “softer” or
less responsive the helicopter feels) This function makes the
best possible use of the infight adjustable gain of most gyros.
18
WFT09
INSTRUCTION
Setting Method
Use up or down button to select GYRO sens
editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button for proper adjustment,
3. Press EXIT after setting
setting , OK button is to enter
(2). Throttle hovering setting
(3). Pitch hovering setting
This function is to set the throttle curve trim at the hovering
point.
Hovering throttle and hovering pitch are fine-tuning adjustments for the throttle and collective
pitch curves individually, affecting performance only around the center point and only in the normal
condition. They allow in-flight tweaking of the curves for ideal setup.
Setting Method
Use up or down button to select Throttle hovering
ing setting , OK button is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button for proper adjustment.
3. Press EXIT after setting.
19
setting/ Pitch hover-
WFT09
INSTRUCTION
(4). HI/LO PIT setting
This function is to set the high and low pitch position at different flying modes.
(5). Trim offset setting
This function is to adjust the servo trim at hovering state.
Optional separate trims in addition to those for the normal condition.
This function is used to automatically change the trim of a helicopter,
for example, when transitioned from hover to flying at high speed. A
clockwise-rotation rotor helicopter tends to drift to the right at high
speed, so an aileron offset may be applied to offset the helicopter to
the left. The necessary elevator offset varies with model geometry, so
it must be determined by noting collective pitch changes at high speed.
The rudder offset is affected by both revo. Mixing and trim lever movement
while in the offset function.
Set up separate trims for each of the three idle-up conditions.
Adjust the idle-up 2 rudder trim to correct for torque at high speeds.
Steps:
1. Open the OFFSET function.
2.Change switch setting to COND.
3. Select IDL2
4. Adjust trim settings as needed.(Ex: rudder to +8%)
5. Close menus and confirm difference in trims between nornal and idle-up 2.
20
WFT09
INSTRUCTION
(6). DELAY
This function is to delay the aerobatics or throttle cut when the
helicopter is in the air so that to avoid the big trim change.
The Delay function provides a smooth transition between the trim
positions whenever OFFSET, REVO. MIXING, or THROTTLE HOLD
functions are turned on and off.
Set up a delay on all 3 channels to ease the transition from one flight condition to another so there are
“hard jumps”.
Steps:
1. Open the DELAY function.
2. Adjust AIL response as needed. (Ex: aileron to +8%)
3. Repeat for other channels.
4. Close menus and confirm slowed transitions.
(7). Governor mixing
This function is to set the governor.
The Governor mixing function is used to adjust the GV-1(Governor)
speed settings(rS1,rS2,rS3) from the transmitter.
Set up a Gv1 governor to use both channels into the reeiver and switch between the governor settings automatically when changing conditions.
Consider setting the battery FailSafe settings and other helpful functions on the GV-1 itself.
Steps:
1. Open and activate the GOVERNOR function.
2. Optional: change cut-off channel to channel 8 and assign switch and direction for on/off(channel 8).
3. Optional: change switch assignment to select governor settings. Ex: select switch that selects the conditions.
4. Adjust governor speed settings per switch position or condition as needed.(Ex: defaults are fine.) Allows head
speed adjustment from transmitter.
5. Close the function.
21
WFT09
INSTRUCTION
(8). Swash and THR mixing
This function is to adjust throttle and pitch mix function.
(9). Cur ve Setting
There are 2 kinds of setting, Normal and Advanced.
22
WFT09
INSTRUCTION
(10)-(16). PROG. NOR. MIX1-7
The mix program is to adjust the flying pose. There are 7series
programs with the same set method.
(17)-(20). PROG. CUR. MIX1-4
There are 4 serious curve mix program, the curve is made up by
2 to 11 point.
23
WFT09
INSTRUCTION
(21). Throttle needle mixing
Throttle needle is a pre-programmed mix that automatically
moves an in-flight mixture servo in response to the Throttle
Stick imputs for perfect engine tuning at all throttle settings.
This function is particularly popular with contest pilots who fly
in a large variety of locations, needing regular engine tuning
adjustments, and requiring perfect engine response at all times
and in all maneuvers. Also popular to minimize flooding at idle
of inverted engine installations or installations with a high tank
position. Not need for fuel injection engine, which do this
automatically.
Setting Method
Use up or down button to select Throttle needle mixing , OK button is to enter
editing.
Steps:
1. Use direction buttons to select editing part.
2. Ajust the travels as needed to match your engine by slowly moving the stick
to each of the points, then adjusting the percentage at that point until the
engine is properly tuned.
3.Set curves for other conditions.
4. Press EXIT after setting.
17. Language
This function is to select the language, Simplified Chinese and
English can be selected.
24
WFT09
INSTRUCTION
SYS SETTING
1.Model selectting
There are 10 helicopter models.
Setting Method
Use up or down button to select Model selecting, OK button is
to enter editing.
Steps:
1. Use direction buttons to select the model.
2. Press OK button.
3. Press EXIT after setting.
2. Model name
This function is to make new names by users.
Setting Method
Use up or down button to select Model selecting, OK button is
to enter editing.
Steps:
1. You can edit the underlined letter
2. Press OK button to choose the word you like.
3. Press EXIT after setting.
25
WFT09
INSTRUCTION
3.ATL
Adjustable travel limit (ATL) makes the channel 3 TRIM LEVER
(THROTTLE TRIM) effective only at low throttle, disabling the trim
at high throttle. This prevents pushrod jamming due to idling trim
changes. This function defaults to ON. If you are not using channel
3 for throttle, youmay want trim operation the same as on all other
channels. To do so, set ATL to OFF.
Setting Method
Use up or down button to select Model selecting, OK button is to enter
editing.
Steps:
1. Use direction buttons to select the model.
2. Press OK button.
3. Press EXIT after setting.
4.Modulation setting
Because of the different receiver modulation PPM/PCM,
the transmitter should be accordance with the receiver
modulation.
Setting Method
Use up or down button to select Modulation setting, OK button is to
enter editing.
PPM and PCM is selectable.
26
WFT09
INSTRUCTION
5.Swash select
There are 6 kinds of swash. You can select the swash
you preferred.
Setting Method
Use up or down button to select Model selecting, OK button is
to enter editing.
Steps:
1. Use +/- buttons to select the model.
2. Press OK button to choose.
3. Press EXIT after setting.
27
WFT09
INSTRUCTION
6.Stick setting
There are 4 kinds of model, you can use up and down direction
button to select the model you preferred.
Setting Method
Use up or down button to select Stick setting , OK button is
to enter editing.
Steps:
1. Use up and down direction buttons to select the model.
2. Press OK button to choose.
3. Press EXIT after setting.
28
WFT09
INSTRUCTION
7.Fail safe
This function is to set responses in case of loss of signal or low RX
battery.
Setting Method
Use up or down button to select Fail safe, OK button is to enter
editing.
Steps:
1. Use direction buttons to select editing part.
2. Choose Channel to change.
3.Set and confirm fail safe conmmand.
4. Press EXIT after setting.
8.Rest setting
This function is to back default.
Setting Method
Use up or down button to select Reset setting, OK button is to enter
editing.
You can select cancel or OK.
29
WFT09
INSTRUCTION
9. Send data
This function is to send the model parameter to another
transmitter. By using a trainer cord, one transmitter can
send the data to another transmitter.
Setting Method
Use up or down button to select Send data, OK button is to
enter editing.
Steps:
1. Select the model data you need to send out.
2. Press OK to send.
30
WFT09
INSTRUCTION
10.Receive data
This function is to receive the model parameter to another
transmitter. By using a trainer cord, one transmitter can
receive the data from another transmitter.
Setting Method
Use up or down button to select Receive data, OK button is to enter
editing.
Steps:
1. Press OK to receive data.
2. Restart the transmitter after receiving the data.
31
WFT09
INSTRUCTION
11.Contrast setting
This function is to adjust the LCD brightness by increasing
or decreasing the contrast value.
Setting Method
Use up or down button to select Contrast setting, OK button is to
enter editing.
Steps:
1. Use +/- button to increase or decrease the value.
2. Press OK button for a while is to back default.
3. Press EXIT after setting.
12.Engineer model
13.About
14.Language
This function is to select the language, Simplified Chinese and
English can be selected.
32
WFT09
INSTRUCTION
TO THE PILOT
WFT09 is the first version. Thank you for using the
radio. We welcome your valuable advice and we will
make progress of the radio.
Welcome to contact us!
www.wflysz.com
sales@wflysz.com
Tel: 0086 755 26581817
Fax: 0086 755 26581821
33

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 16
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:a6fa6ae0-b060-4522-946a-8d2386d39a97
Modify Date                     : 2007:05:24 11:43:41+02:00
Create Date                     : 2007:05:24 11:43:24+02:00
Metadata Date                   : 2007:05:24 11:43:41+02:00
Document ID                     : uuid:5a504b6e-7bf9-4111-8e77-27185419f88d
Format                          : application/pdf
Title                           : 备份manual
Creator                         : CorelDRAW 12.0 版
Producer                        : Corel PDF Engine Version 1.0.0.525

EXIF Metadata provided by EXIF.tools