Shen Zhen WFLY Technology Development WFT09II RADIO CONTROL SYSTEM User Manual
Shen Zhen WFLY Technology Development Co., Ltd. RADIO CONTROL SYSTEM Users Manual
Contents
- 1. USERS MANUAL 1
- 2. USERS MANUAL 2
- 3. USERS MANUAL 3
- 4. USERS MANUAL 4
USERS MANUAL 1
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1536775 |
| Application ID | pG0ZVWljXHvDeBgOZxWi6g== |
| Document Description | USERS MANUAL 1 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 335.5kB (4193735 bits) |
| Date Submitted | 2011-09-06 00:00:00 |
| Date Available | 2011-09-06 00:00:00 |
| Creation Date | 2011-09-06 15:44:58 |
| Producing Software | Acrobat Distiller 7.0.5 (Windows) |
| Document Lastmod | 2011-09-06 15:45:03 |
| Document Title | Users Manual |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | Administrator |
RADIO CONTROL SYSTEM PCMS 4096 PCMS Receiver, Dual MCU, Dual Antenner.Dual circuits INSTRUCTION MANUALV2 NOTICE Read the instruction before operation! INSTRUCTION Thank you for purchacing product! SERVICE 1.Retailers to provide free maintenance for six months (apart from artificial damage) 2. WFLY retailers will always provide life- long maintance INSTRUCTION CATALOGUE Contents-------------------------------------------------------------------Transmitter front----------------------------------------------------------Transmitter back----------------------------------------------------------Receiver--------------------------------------------------------------------Trainer function-----------------------------------------------------------Flying safety warnings---------------------------------------------------Features--------------------------------------------------------------------Buttons---------------------------------------------------------------------2.4G Code matching-----------------------------------------------------Adjust the stick head----------------------------------------------------C hange the throttle direction of mode1 or 2 ---------------------------- 08 09 10 11 12 13 14 15 16 17 18 HELICOPTER SYS SETTING 1. Model selecting--------------------------------------------------------- 23 2. Model name------------------------------------------------------------ 24 3. Model setting----------------------------------------------------------- 25 4. ATL----------------------------------------------------------------------- 26 5. Modulation setting----------------------------------------------------- 27 6. RF setting------------------------------------- -------------- ------------ 27 7. Swash select------------------------------------------------------------ 28 8. Stick setting------------------------------------------------------------- 29 9. Adjustment--------------------------------------------------------------- 30 10 .Res e t setting--------------------------------------------------------------31 11. Send data-------------------------------------------------------------- 32 12. Receive data---------------------------------------------------------- 33 13. Sound------------------------------------------------------------------- 34 14. Contrast setting------------------------------------------------------- 35 About----------------------------------------------------------------------- 35 Language--------------------------------------------------------------- 36 NORMAL SETTING 1. Monitor------------------------------------------------------------------2. Dual rate & Exponential----------------------------------------------3. Servo reverse----------------------------------------------------------4. End point---------------------------------------------------------------3 37 38 39 40 INSTRUCTION 5. Sub trim---------------------------------------------------------------6. Swash param setting-----------------------------------------------7. Auxiliary channels setting-----------------------------------------8. Throttle curve setting-----------------------------------------------9. Pitch curve setting--------------------------------------------------10. Revolution mixing--------------------------------------------------11. Trim step setting----------------------------------------------------12. Throttle cut setting-------------------------------------------------13. Fly model switch----------------------------------------------------14. Throttle holding setting--------------------------------------------15. Fail safe--------------------------------------------------------------16. TIMER----------------------------------------------------------------- 41 42 43 44 46 48 49 50 51 52 53 54 ADVANCED (1). GYRO sens setting--------------------------------------------(2). Throttle hovering setting-------------------------------------(3). Pitch hovering setting-----------------------------------------(4). HI/LO PIT Setting----------------------------------------------(5). Trim offset setting---------------------------------------------(6). DELAY-----------------------------------------------------------(7). Governor mixing-----------------------------------------------(8). Swash and THR mixing---------------------------------------(9). Cuve setting----------------------------------------------------(10). PROG.NOR.MIX1-7-----------------------------------------(17). PROG.CUR.MIX1-4-----------------------------------------(21). Throttle needle mixing--------------------------------------(22) Code matching ---------------------------------------------- 56 57 58 59 60 61 62 63 64 67 68 69 69 INSTRUCTION AIRPLANE SYS SETTING 1.Model selecting---------------------------------------------------------- 73 2.Model name-------------------------------------------------------------- 74 3.Model setting------------------------------------------------------------ 75 4.ATL------------------------------------------------------------------------ 76 5.AIL-2---------------------------------------------------------------------- 77 6.Modulation setting------------------------------------------------------ 78 7.RF setting-------------------------------------- ----------------- --------- 79 8.Stick setting------------------------------------------------------------- 80 9.Adjustment- ------------------------------------------------------------ 81 10.Reset setting----------------------------------------------------------- 82 11.Send data-------------------------------------------------------------- 83 12.Receive data---------------------------------------------------------- 84 13.Sound------------------------------------------------------------------ 85 14.Contrast setting-------------------------------------------------------- 85 About----------------------------------------------------------------------- 85 Language------------------------------------------------------------------ NORMAL SETTING 1.Monitor------------------------------------------------------------------- 86 2.Dual Rate & Exponential Setting------------------------------------- 87 3.Servo Reverse---------------------------------------------------------- 88 4.End Point---------------------------------------------------------------- 89 5.Sub Trim----------------------------------------------------------------- 90 6.Auxiliary Channels Setting------------------------------------------- 91 7.Throttle Curve Setting------------------------------------------------ 92 8.Trim Step Setting------------------------------------------------------- 94 9.Flaperon----------------------------------------------------------------- 95 10.Flap Trim--------------------------------------------------------------- 96 11.Ail-diff------------------------------------------------------------------- 97 12.Elev-flap--------------------------------------------------------------- 98 INSTRUCTION 13.Throttle Cut Setting-------------------------------------------------- 99 14.Idle Down-------------------------------------------------------------- 100 15.Fail Safe--------------------------------------------------------------- 101 16.Timer------------------------------------------------------------------- 102 17.Advanced-------------------------------------------------------------- 103 ADVANCED (1). curve Setting---------------------------------------------------------- 105 (2)-(8). PROG.NOR.MIX1-7---------------------------------------------- 106 (9)-(12). PROG.CUR.MIX1-4-------------------------------------------- 107 (13). Air Brake-------------------------------------------------------------- 108 (14). Elevon----------------------------------------------------------------- 109 (15). Ailvator---------------------------------------------------------------- 110 (16). V-tail------------------------------------------------------------------- 111 (17). Snap-roll-------------------------------------------------------------- 112 (18). Delay------------------------------------------------------------------ 113 (19). Throttle Needle Mixing--------------------------------------------- 114 (20). Gyro Sens Setting--------------------------------------------------- 115 (21). Code matching --------------------------------------------------- 115 GLIDER SYS SETTING 1.Model Selecting----------------------------------------------------------2.Model Name---------------------------------------------------------------3.Model Setting-------------------------------------------------------------4.Atl---------------------------------------------------------------------------5.Ail-2-------------------------------------------------------------------------6.Modulation Setting---------------------------------------------------- - 119 120 121 122 123 124 INSTRUCTION 7.RF Setting---------- -------------------- --------------------------------- 8.Stick Setting-------------------------------------------------------------9.Adjustment-------------------------------------------------------------10.Reset Setting----------------------------------------------------------11.Send Data--------------------------------------------------------------12.Receive Data----------------------------------------------------------13.Sound-------------------------------------------------------------------14.Contrast Setting-------------------------------------------------------About---------------------------------------------------------------------Language--------------------------------------------------------------------- 124 125 126 127 128 129 130 131 131 131 NORMAL SETTING 1.Monitor--------------------------------------------------------------------2.Dual Rate & Exponential Setting—-----------------------------------3.Abk. Curve Setting------------------------------------------------------4.Servo Reverse-----------------------------------------------------------5.End Point-----------------------------------------------------------------6.Sub Trim------------------------------------------------------------------7.Auxiliary Channels Setting--------------------------------------------8.Trim Step Setting--------------------------------------------------------9.Flaperon------------------------------------------------------------------10.Flap Trim-----------------------------------------------------------------11.Ail-diff--------------------------------------------------------------------12.Elev-flap----------------------------------------------------------------13.Fail Safe-----------------------------------------------------------------14.Timer--------------------------------------------------------------------15.Advanced----------------------------------------------------------------- 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 ADVANCED (1).Curve setting--------------------------------------------------------(2)-(8).PROG.NOR.MIX1-7--------------------------------------------(9)-(12).PROG.CUR.MIX1-4-------------------------------------------(13).butterfly---------------------------------------------------------------(14).elevon----------------------------------------------------------------(15).ailvator---------------------------------------------------------------(16).V-TAIL----------------------------------------------------------------(17).Start OFS------------------------------------------------------------(18).Speed OFS----------------------------------------------------------(19). Code matching ----------------------------------------------------7 148 149 150 151 152 153 154 155 156 156 INSTRUCTION Contents Thank you for your attention and support to WFLY radio! WFLY promises every WFT09S radio control system include the following contents: 1. 4096 transmitter 2. Battery holder for transmitter 3. Neckstrap 4. Trainer cable/Data transfer cable 5. Simulator cable 6. WFR09S 2. 4GHz 9 channel receiver PCMS 7.Li-po Voltage Regulation 8. English instruction manual. INSTRUCTION Contents 1. Transmitter 2. Transmitter battery holder 3. Neckstrap 4. Trainer cable/Data 5. Simulator cable transfer cable 7.Li-po Voltage Regulation 8. CD manual 6. WFR09S 2 . 4GHz 9ch receiver INSTRUCTION TRANSMITTER MODEL NO.: MODULATION: PPM, PCMS 1024, PCMS 4096 OUTPUT POWER: ≤100mW POWER SUPPLY: 9.6-12V CURRENT DRAIN: 250mA Band: 2.4GHz TRANSMITTER FRONT Alarm light Antenna Power light Buzzer RF light VB VA VC Switch C Switch D Switch E Switch B Trainer switch Switch A Switch F VL VR Elevator trim Neckstrap attachment Rudder/elevator stick Power switch Aileron/throttle stick Throttle trim Aileron trim Rudder trim LCD Menu Exit Increase Decrease OK Charge hole Up / Right Left / Down 10 INSTRUCTION TRANSMITTER BACK DSC Battery cover 11 INSTRUCTION RECEIVER Resolution 4096 (with PCMS 4096 modulation) 2.4GHz 9 Channels receiver Dual MCU, Dual antenna, Dual circuits , Resolution 4096 receiver MODEL NO.: WFR09S TYPE: 9 CH PPM /PCMS 1024/PCMS 4096 BAND: 2.400-2.483GHz POWER SUPPLY: 4.8-6V RECEIVER SENSITIVITY: - 97dBm WEIGHT: 14.8 g DIMENSION: 44.8mm x27.9mm x16.39mm WFR09S 9 Channels Receiver (PCMS) 1．AIL：Aileron (Channel 1)-----------------------2．ELE：Elevator (Channel 2)---------------------3．THR：Throttle (Channel 3)----------------------4．RUD：Rudder (Channel 4)----------------------5．GYR：Landing Gear/Gyro (Channel 5)--------6．PIT：Pitch (Channel 6)------------------------------ 7．AUX1：Auxiliary channel 1 (Channel 7)--------8．AUX2：Auxiliary channel 2 (Channel 8--------- 9．Power：Input + 4.8-6V----------------------------- (There are 9 rows needles, 3 needles in each row, from the top needle to the bottom, the 3 needles are PCMS/PPM pulse, +5V and Ground.) This receiver has Fail safe function. Characteristic Can effectively select the best signal Enhance the reliability Improve the response speed Enhance the anti-interference Increased use of range 12 INSTRUCTION Trainer function Two WFT09SII transmitters can transfer data and realize trainer function. Setting Method: 1).Data transfer function: use Trainer cable/Data transfer cable to connect two WFT09SII transmitter. Select “Send data/receive data” in SYS setting to transfer the data. 2).Trainer function: use Trainer cable/Data transfer cable to connect two WFT09SII transmitters. Insert RF module to the trainer transmitter, student transmitter doesn’t insert the RF module. Pull Trainer switch for student transmitter operating. If any wrong operation occurs, trainer pushes trainer switch and student transmitter stops sending signal, trainer transmitter controls the aircraft. 13 INSTRUCTION FLYING SAFETY WARNINGS Special Symbol Instruction To use the product safely, please pay attention to the instruction as follows. Please pay special attention to the symbol as follows: Dangers：If you use it without proper operation, it is possible to hurt you seriously or may even cause death. Warnings：If you use it without proper operation, it may make you or others to hurt badly or may even cause death, and it may cause slight hurt or damage to things. Notices：If you use it without proper operation, it may cause you to hurt slightly or damage things , but it won't hurt you seriously normally. Notices：Children under 14 must be accompanied and instructed by adults! Notices: Turn on the transmitter first, then the receiver. When turning off the system, turn off the receiver first, then the transmitter. Notices: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Flying Notice(warning) Forbiddance! Obligation! Warning! Do not fly at night , in rain day ,or in strong wind, which will damage the device or plane. This device is not water-proof. Please check every servo works properly and eliminate any disturbing signals before you play it. 14 INSTRUCTION FEATURES Computerized transmitter High Speed, High Resolution, optimized 2.4GHz PCMS 4096 Convenient stick adjustment, make you free usage Tree-like Multilayer Menu, human oriented design Excellent white LED backlight, less visual tiredness 132 X 64 FSTN LCD, easy operating buttons 85 model memory 10 point curve(in any X and Y direction edition) Easy complex curve adjustment Different Sub trim adjustment sound, easy identify the center Data transfer function, easy teaching and learning Multi-function, intuitive data setting, easy checking Tightness and length of the control stick can be adjusted freely Excellent touch of the stick movement 3 independence timer, all can be set to count down or increment 15 INSTRUCTION Buttons MENU Menu button brings you to the function list of the transmitter. EXIT Exit button is to back the previous menu or exit edit. This button is to increase the value. If you press it for a while, the increasing speed will be faster. This button is to decrease the value. If you press it for a while, the decreasing speed will be faster. Cursor buttons Move the cursor. OK The button in the middle of the direction buttons is the OK button. The function is as follows: To enter the function list. To enter the edit function. To back the default for long time press. 16 INSTRUCTION WFLY 2 . 4 G H z O p e r a t i o n i n s t r u c t i o n s 2.4G system can automatical l y r e c o g n i z e W F L Y P C Ms a n d P P M . 1 .Code matching Description This function is useful under the situation when the transmitter need to be match and bind with receiver. setting Enter "normal settings" and choose "advanced", use up and down key to choose coding, press ok to select. The screen will display "OK: Cancel". Set your receiver to coding mode, and use up or down button to choose Ok and then press OK button. The screen will display "Coding wait.." Code matching will be succeeding after the receiver back to normal mode. 2 . Fail S a f e S e t t i n g A.Power on receiver. B.Press Set of the module then start transmitter and hold SET for 2 seconds. The green LED flashes, indicating the transmitter enters the code matching status. C. The Green LED of receiver flashes, the output data of transmitter is the data of Fail Safe Setting of the receiver. D. Due to the heavy interference or out of normal range, the receiver enters FailSafe. The Red LED of the receiver lights when it is in Fail Safe status. 17 INSTRUCTION Adjust the stick head: Top thread Allen key Stick head Put the stick head cover the control rod on the left and right sides,don't twist down the stick head to the bottom, and then put top thread with allen key to adjust the height Stick you need. Twist the top thread down from here, the height of the stick head depends on the depth of the top thread. Adjust the height higher: frist make the top thread loose with the allen key, then twist the stick head up, then, make the top thread tighten with allen key, Ok, the stick head was turned up. Adjust the height lower: frist make the top thread loose with the allen key, then twist the stick head down, then, make the top thread tighten with allen key, Ok, the stick head was turned down. Steps : Put the stick head on the stick. 2 Put the top thread in the stick head with allen key. 3. Addjust top thread in the stick head with allen key to fix the height of the stick head. 18 INSTRUCTION change the throttle direction of mode1 or 2: Bolt 4 Bolt 1 Bolt 2 Bolt 3 Take the metal chip and the screw down, and put it on the similar position of the right side . Set up release link and springer, according your habit to addjust the the tightness of screw 2 to adjust the control feeling. Take repositor and spring down, and put it on the left side of the location of corresponding.then twist bolt 1 down until withstand the adjust nail in case adjust nail will move away. 19 Put on the metal chip, according your habit to adjust the elasticity of screw 3 and screw 4 to adjust the damp of throttle control feeling. HELICOPTER INSTRUCTION HELICOPTER Press Menu and turn on the transmitter to enter SYS SETTING. Select MODEL SETTING, press OK button to select the model type. Restart the transmitter after setting. 20 HELICOPTER INSTRUCTION Editing mode and function introduction 1. Opening Screen Turn on the power switch, the LCD displays as follows. Voltage Timer A Start time Model type Timer B Throttle trim display Timer C Elevator trim display Rudder trim display Aileron trim display The opening screen displays the voltage, timer, model, aileron, throttle, elevator and rudder state. Note: Press EXIT you can see the model name. Model name 2. Menu Screen There are “Normal setting”, “SYS setting”, “Advanced”. A. Normal setting Turn on the transmitter, press the menu button, the LCD displays as follows. 1. MONITOR 2. DUAL RATE & EXPONENTIAL SETTING 3. SERVO REVERSE 4. END POINT 5. SUB TRIM 6. SWASH PARAM SETTING 7. AUXILIARY CHANNELS 8. THROTTLE CURVE SETTING 9. PITCH CURVE SETTING 10. REVOLUTION MIXING 11. TRIM STEP SETTING 12. THROTTLE CUT SETTING 13. FLY MODEL SWITCH 14. THROTTLE HOLDING SETTING 15. FAIL SAFE 16. TIMER 17. ADVANCED 18. LANGUAGE Setting method: 1. Use direction button to select the editing part, use up/down buttons to select function item. Left/right direction button to turn page. 2. Press OK button to enter submenu. The submenu function is in the next chapter. 3. Press EXIT button to back previous menu and the data is set automatically. 21 HELICOPTER INSTRUCTION B. SYS SETTING Press Menu and turn on the power switch, the LCD displays as follows. Setting method: 1. Use direction button to select the editing part,use up/down buttons to select function item. Left/right direction button to turn page. 1. MODEL SELECTING 2. MODEL NAME 3. MODEL SETTING 4. ATL 5. MODULATION SETTING 6. SWASH SELECT 7. STICK SETTING 8. ADJUSTMENT 9.REST SETTING 10.SEND DATA 11. RECEIVE DATA 12. SOUND 13.CONTRAST SETTING 14. ENGINEER MODEL 15. ABOUT 16. LANGUAGE 2. Press OK button to enter submenu. The submenu function is in the next chapter. 3. Press EXIT button to back previous menu and the data is set automatically. C. ADVANCED 1. Enter “NORMAL SETTING”, use right direction button to turn page, select “ADVANCED”. Press OK button to enter. Setting method: 1. Use direction button to select the editing part,use up/down buttons to select function item. Left/right direction button to turn page. 2. Press OK button to enter submenu. The submenu function is in the next chapter. 3. Press EXIT button to back previous menu and the data is set automatically. 22 HELICOPTER INSTRUCTION SYS SETTING 1.Model selectting There are 85 helicopter models. You can select any one to set. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Model selecting”, OK button is to enter editing. Steps: 1. Use up/down direction button to select the model. 2. Press OK button to select. 3. Press EXIT after setting. 23 HELICOPTER INSTRUCTION 2. Model name This function is to make new names by users. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Model name”, OK button is to enter editing. Steps: 1. You can edit the underlined letter. 2. Press OK button to choose the word you like. 3. Press EXIT after setting. 24 HELICOPTER INSTRUCTION 3. Model setting You can select the model type. There are three type: HELI, ACRO, GLID. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Model setting”, OK button is to enter editing. Steps: 1. Use up/down direction button to select the model type. 2. Press OK button to confirm. 3. Press EXIT after setting. 25 HELICOPTER INSTRUCTION 4. ATL Adjustable travel limit (ATL) makes throttle trim effective only at low throttle, disabling the trim at high throttle. This prevents pushrod jamming due to idling trim changes. This function defaults to ON. If you are not using channel 3 for throttle, you may want trim operation the same as on all other channels. To do so, set ATL to OFF. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “ATL”, OK button is to enter editing. Steps: 1. Use direction buttons to select the editing part. 2. Press +/- button to set ATL function. 3. Press EXIT after setting. 26 HELICOPTER INSTRUCTION 5.Modulation setting Because of the different receiver modulation PPM/PCMS1024 /2.4G PCMS4096, the transmitter should be accordance with the receiver modulation. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Modulation setting”, OK button is to enter editing. Steps: 1. Use direction buttons to select the editing part. 2. Press OK button to confirm. Restart the transmitter and it works. 6.RF setting Description The user can turn off the RF module during emulation to minimize power consumption. Setting method Press menu button during power on to enter system setting menu, use up/down button to select "RF setting". press OK button to enter setting interface. as shown on the picture, choose ON or OFF and press OK. Reboot the transmitter to active. 27 HELICOPTER INSTRUCTION 7.Swash select There are 6 kinds of swash. You can select the swash you preferred. If you use 120 degree CCPM helicopter, the servos will realize mix function automatically. Please select the swash according to your helicopter swash type. 1 servo (not CCPM, normal helicopter) 2 servos (180 degree) 3 servos (90, 120, 140 degree) 4 servos (90 degree) Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Swash select”, OK button is to enter editing. Steps: 1. Use direction button to select the editing part. 2. Press +/- button to choose the swash type. 3. Press EXIT after setting. 28 HELICOPTER INSTRUCTION 8.Stick setting There are 4 kinds of model, you can use up/down direction button to select the model you preferred. 1-aileron 2-elevator 3-throttle 4-rudder Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Stick setting”, OK button is to enter editing. Steps: 1. Use direction button to select the editing part. 2. Press up/down button to choose Stick mode. 3. Press EXIT after setting. 29 HELICOPTER INSTRUCTION 9.Adjustment This function is to set the central, high and low point of four sticks when users changed the mode I or II by themselves. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “ADJUSTMENT”, OK button is to enter editing. Steps: 1. Use direction button to select the editing part. Take the aileron adjustment for example . 2. Make the stick in the mid-point location. Press OK button to select any stick you want to adjust. 3. Select into the Figure 2, when the "center" highlights, press the "ok" button directly (the mid-point has been adjusted), then enter the high adjust. 4. The "high” highlights, take the stick gently in the right side (throttle /elevator in the top, aileron / rudder in the right),press "ok" button ( the max adjust is OK), enter the low adjustment. 5.The "low" highlights, take the stick gently in the left side (throttle /elevator in the bottom, aileron / rudder in the left),press "ok" button (the min adjust is OK). 6. Press OK or RESET to confirm the record or reset. 7. If the record is wrong, press OK will back to step 3. 30 HELICOPTER INSTRUCTION 10.Reset setting This function is to back default. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Reset setting”, OK button is to enter editing. Steps: 1. Use direction button to select the editing part. 2. Press +/- button to back default. 3. Press EXIT after setting. 31 HELICOPTER INSTRUCTION 11. Send data Two transmitters (WFT09S) can copy data by a trainer cable/data transfer cable. This function together with the next function “Receive data” can realize the data copy. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Send data”, OK button is to enter editing. Steps: 1. Select the model data you want to send out. 2. Press OK to send. 32 HELICOPTER INSTRUCTION 12.Receive data Two transmitters (WFT09S) can copy data by a trainer cable/data transfer cable. This function together with the previous function “Send data” can realize the data copy. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Receive data”, OK button is to enter editing. Steps: 1. Press OK to receive data. 2. Restart the transmitter after receiving the data and it works. 33 HELICOPTER INSTRUCTION 13.Sound This function is to select the sound ON and OFF. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “SOUND”, OK button is to enter editing. Steps: 1. Use +/- button to select ON and OFF. 2. Press OK button to confirm. 3. Press EXIT after setting. 34 HELICOPTER INSTRUCTION 14.Contrast setting This function is to adjust the LCD brightness by increasing or decreasing the contrast value. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Contrast setting”, OK button is to enter editing. Steps: 1. Use +/- button to increase or decrease the value. 2. Press OK button for a while is to back default. 3. Press EXIT after setting. 15.About This item shows the Version of WFLY radio. 35
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 Modify Date : 2011:09:06 15:45:03+08:00 Create Date : 2011:09:06 15:44:58+08:00 Metadata Date : 2011:09:06 15:45:03+08:00 Creator Tool : PScript5.dll Version 5.2 Format : application/pdf Title : WFT09S鑻辨枃20110120 Creator : Administrator Document ID : uuid:63afa38e-35e8-4da4-ba80-7b4402da2873 Instance ID : uuid:544fab40-8848-4bb5-ba7f-31149b1be5e7 Producer : Acrobat Distiller 7.0.5 (Windows) Page Count : 35 Author : AdministratorEXIF Metadata provided by EXIF.tools