ShenZhen Aoni Electronic Industry A8B036 Bluetooth Headset User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3770335
Application ID	2x/W264w22EkQJNl8ULeMA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	31.1kB (388710 bits)
Date Submitted	2018-03-06 00:00:00
Date Available	2018-03-06 00:00:00
Creation Date	2018-02-08 17:27:34
Producing Software	Microsoft? Office Word 2007
Document Lastmod	2018-02-08 17:27:34
Document Title	User Manual
Document Creator	Microsoft? Office Word 2007
Document Author:	zhengl

User’s Manual
Model No: B036
Important safety instruction
If used in the correct method, this design and production of this product can ensure your personal safety
completely. However, any inappropriate use may lead to potential risk and danger of electric shock or fire
hazard. Please read all the safety instructions before installing and using the product. In particular, attention
shall be given to the following information:
1. It needs to be stored or used in the ambient temperature.
2. It shall not be placed in water or wet locations.
3. It can’t be disposed randomly for it may cause environmental pollution.
4. Without approval, It shall not be disassembled or repaired.
5. The built-in lithium battery can’t be disposed in the fire or other places to prevent causing fire hazards.
6. It shall be cleaned with dry cloth.
7. Whenever there is damage, it needs to be repaired by professional personnel.
Charging the battery
Fully charge the battery for about 3.5 hours before using the battery for the first time.
1. Plug the smaller end of USB charging cable into the Micro-USB interface of the connector.
2. Next, plug the other end of USB charging cable into other power charging devices or a computer with the
power on.
Status
LED indicator
Low battery
Charging
When power is less than 10%, the battery voltage will lower 3.3V,
then there will be a voice prompt “dududu”, while the RED LED
flashes twice per second---this alarm occurs every two minutes.
when the voltage is lower 3.1V,the earphone will shut down
automatically
The red light solid on.
Fully charged
The red indicator will go out .
Package content
1. Wireless headphone
2. Micro USB charging cable
3. 3.5mm audio cable
4. Quick user guide
5. PU bag
Earphone indicator
1.LED Charging indicator
2.Charging Port
3.Volume-/Previous Track
4. Volume+/Next Track
5. LED Indicator
6.Power Button
7．AUX Port
8.MicroPhone
Product feature
Pairing name
Li-battery capability
Talking time
Playing time
Charging time
Charger mode
Straight-line distance
Operation instructions
Operation instructions
function
Key operation
power on
Power off
Pairing
B036
400 mAh
20hours
20 hours
3.5 hours
Micro USB 5V/1A
≥10m
description
At Power off state, press power button for 3s,
there is voice prompt “Dudududu". Loose the
button, it will go into pairing state automatically
Long
press
if it’s first device pairing; if the Bluetooth
power button
devices information existed before, it will go
for 3s
into standby state directly (headset re-pairs
automatically in 3 minutes). it will power off if
10minutes no connection at standby state.
Long Press
At Power on state, press power button for 3s,
power button
there is voice prompt “dudududu"
for 4s
At Power off state, long press power button for
Press power
5s, and it will go into pairing state while there is
button for
a voice prompt "dududu". At the same time the
5s
headphone will be detected by other device,
but if it’s not connected within 3 minutes, the
LED status
Blue LED light
on for 2s, then
it flash in an
alternating
pattern
(200mS)
Red LED light
on 2s and then
go off
Red and blue
LED flash
alternately
headphone will go into standby status.
connection
N/A
status
Re-pairing
Click power
Automaticall
button
Disconnect(
automaticall
y)
Disconnect
Play
Pause
Volume up
Volume
down
Next Track
Previous
Track
Answer
call
On call
Reject call
Blue LED flash
There have voice prompt “Di”when Bluetooth
twice every 5s
pairing successfully
Blue
LED
Click power button at standby station, the
flashes in an
headphone will enter into the repairing list
200ms interval
If the phone disconnects automatically, there is Blue
LED
no prompt, the headphone to into standby flashes in an
status .
200ms interval
When the distance is out of range, the
headphone will go into re-pair status in
Blue
LED
3minutes; it will go into standby status in 10
flashes in an
minutes no connection ; also it will closed
200ms interval
automatically if no connection after 10
minutes.
Blue
LED
Short press
Short press power button can replay the media
Flashes twice
power button while the headphone is in pause status
every 5sec
Blue LED Flesh
Short press Short press power button can pause the
twice
every
power button media while the headphone is in play status
5sec
Short press Volume+ can increase the volume
Blue LED Flesh
Short press level while on music playing mode or talk
twice
every
Volume+(15
mode, there will hear "beep" while the volume
5sec
Level )
is to Max
Short press Volume- can decrease the volume
short press
Blue LED Flesh
level while on music playing mode or talk
Volume-"(15
twice
every
mode, there will hear "Di" at min volume while
Level )
5sec
the volume is to Min
Blue LED Flesh
Long Press
Long press Volume+ to go to next song
twice
every
Volume+
5sec
Blue LED Flesh
Long Press
Long press Volume- to go to next song
twice
every
Volume5sec
RED LED flash
Short press power button can answer a call
fast
in
an
Short press
while there is a call incoming; again a short
alternating
power button
press of power key can end a call
pattern
(200mS)
Blue LED light
N/A
N/A
will be always
on
Long press
Press and hold power button for approximately
power button
2s can reject a call while there is a call
for 2s
incoming
Short Press
Volume+/Short press
power button
Short Press both Volume+/- at the same time
when the device is connected
Short Press the power button can end a call
while the call in progress
Redial last
number
Double click
power button
RED LED flash
in
an
Double click power button can do redial last fast
alternating
number
pattern
(200mS)
Clear
pairing list
Long Press
Volume+/- 5s
At the power on status, Long Press button RED
and
Volume+/- for 5s, the headphone will clear up BLUE LED light
the pairing list and enter into pairing mode
on 2s
Siri
End call
Press button
Press both Volume+ & power button at the
Volume+ &
same time, the hardware will reset
power button
Mic Mute on Long press
Long press Volume-for 3s at call status, the
call
Volumeheadphone will go into/out mute
When in charging, the red LED will be always on; once the energy is full,it will go
Charging
off
When the Audio cable is plug in, the headphone will play music in line-in
Line in
mode(suggestion: pls disconnect bluetooth manually, or the music quality will be
affected)
When power is less than 10%, the battery voltage will lower 3.3V, then there will
be a voice prompt “dududu”, while the RED LED flashes twice per second--this
low battery
alarm occurs every 1minutes. when the voltage is lower 3.1V,the earphone will
shut down automatically
Hardware
Restoration
Pairing the headphones with a computer
1.Before pairing the headphone with your computer, please
make sure your computer or laptop can
support bluetooth function. If not, you must purchase a bluetooth adapter
(preferably version 2.1 or above).
2. Insert the bluetooth adapter to the computer, and make sure the bluetooth function of the computer is
already activated.
3. Press the power button about 5s when the headphone is at power off status. It will go into paring mode
when the blue and red LED light flash alternately, while you can also hear a prompt
4. Open the bluetooth software and choose to search the bluetooth device, and after few seconds, the
names of bluetooth device will list out.
6. Click the pairing name “B036”to pair, when there is a prompt “beep”, this means your headphone is
paired successfully .
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1)
Reorient or relocate the receiving antenna.
2) Reorient or relocate the receiving antenna.
3) Reorient or relocate the receiving antenna.
4) Consult the dealer or an experienced radio/TV technician for help important announcement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition
without restriction.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 6
Language                        : zh-CN
Author                          : zhengl
Creator                         : Microsoft? Office Word 2007
Create Date                     : 2018:02:08 17:27:34+08:00
Modify Date                     : 2018:02:08 17:27:34+08:00
Producer                        : Microsoft? Office Word 2007

EXIF Metadata provided by EXIF.tools