Sherwood Rd 6513 Users Manual 6513(A)

RD-6513 to the manual 75ab421f-1826-415b-9dee-287aaaa5bfc1

2015-02-02

: Sherwood Sherwood-Rd-6513-Users-Manual-445973 sherwood-rd-6513-users-manual-445973 sherwood pdf

Open the PDF directly: View PDF .
Page Count: 44

AUDIO/VIDEO RECEIVER

OPERATING INSTRUCTIONS

RD-6513

cover 2008.8.21 12:21 PM 페이지 2

ENGLISH

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other.

A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit

into your outlet, consult an electrician for replacement of

the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the

apparatus.

When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus have been

exposed to rain or moisture, does not operate normally,

or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

PORTABLE CART WARNING

RD-6513(A) 2008.8.21 12:19 PM 페이지 3

ENGLISH

Introduction

: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This symbol is intended to alert the user to the presence

of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence

of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

Caution regarding installation

Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure.

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION :

WARNING

Do not block ventilation openings or stack other equipment on the top.

READ THIS BEFORE OPERATING YOUR UNIT

FOR YOUR SAFETY

Units shipped to the U.S.A and CANADA are designed for operation

on 120 V AC only.

Safety precaution with use of a polarized AC plug.

However, some products may be supplied with a nonpolarized plug.

U.S.A

CANADA

120 V

• Leave a space around the unit for sufficient ventilation.

• Avoid installation in extremely hot or cold locations, or in an area

that is exposed to direct sunlight or heating equipment.

• Keep the unit free from moisture, water, and dust.

• Do not let foreign objects in the unit.

• The ventilation should not be impeded by covering the ventilation

openings with items, such as newspapers, table-cloths, curtains, etc.

• No naked flame sources, such as lighted candles, should be placed

on the unit.

• Please be care the environmental aspects of battery disposal.

• The unit shall not be exposed to dripping or splashing for use.

• No objects filled with liquids, such as vases, shall be placed on the

unit.

• Do not let insecticides, benzene, and thinner come in contact with

the set.

• Never disassemble or modify the unit in any way.

■Notes on the AC power cord and the wall outlet.

• The unit is not disconnected from the AC power source(mains) as

long as it is connected to the wall outlet, even if the unit has been

turned off.

• To completely disconnect this product from the mains, disconnect

the plug from the wall socket outlet.

• When setting up this product, make sure that the AC outlet you are

using is easily acceptable.

• Disconnect the plug from the wall outlet when not using the unit for

long periods of time.

CAUTION

: To prevent electric shock, match wide blade of

plug to wide slot, fully insert.

: Pour éviter chocs électriques, introduire la lame

la plus large de la fiche dans la borne

correspondante de la prise et pousser jusqu’ au

fond.

ENERGY STARⓇis a U.S. registered mark. As an

ENERGY STARⓇPartner, Sherwood has

determined that this product meets the ENERGY

STARⓇguidelines for energy efficiency.

CAUTION

ATTENTION

Note to CATV System Installer :

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper

grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point

of cable entry as practical.

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

RD-6513(A) 2008.8.21 12:19 PM 페이지 4

ENGLISH

CONTENTS

• IMPORTANT SAFETY INSTRUCTIONS .............................................................................................................................. 3

Introduction

• READ THIS BEFORE OPERATING YOUR UNIT ................................................................................................................. 4

System Connections ......................................................................................................................................................... 6

Front Panel Controls ....................................................................................................................................................... 11

Remote Controls ............................................................................................................................................................... 13

• REMOTE CONTROL OPERATION RANGE ....................................................................................................................... 14

• LOADING BATTERIES ....................................................................................................................................................... 14

Operations

• LISTENING TO A PROGRAM SOURCE ............................................................................................................................ 15

• SURROUND SOUND .......................................................................................................................................................... 18

• ENJOYING SURROUND SOUND ...................................................................................................................................... 19

• LISTENING TO RADIO BROADCASTS ............................................................................................................................. 24

• RECORDING ....................................................................................................................................................................... 26

• OTHER FUNCTIONS .......................................................................................................................................................... 28

System Setup ..................................................................................................................................................................... 29

• SETTING THE SYSTEM .................................................................................................................................................... 31

• SETTING THE INPUT ......................................................................................................................................................... 33

• SETTING THE SPEAKER SETUP ...................................................................................................................................... 34

• SETTING THE CH LEVEL .................................................................................................................................................. 39

• SETTING THE PARAMETER ............................................................................................................................................. 41

Troubleshooting Guide ................................................................................................................................................... 43

Specifications .................................................................................................................................................................... 44

RD-6513(A) 2008.8.21 12:19 PM 페이지 5

ENGLISH

System Connections

• Do not plug the AC input cord into the wall AC outlet until all connections are completed.

• Be sure to observe the color coding when connecting audio, video and speaker cords.

• Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver.

1. CONNECTING ANTENNAS

• Change the position of the FM indoor antenna until you

get the best reception of your favorite FM stations.

• Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC

input cord and set it to a direction for the best reception.

• If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of

the AM loop antenna.

• A 75Ωoutdoor FM antenna may be used to further

improve the reception. Disconnect the indoor

antenna before replacing it with the outdoor one.

RD-6513(A) 2008.8.21 12:19 PM 페이지 6

ENGLISH

2. CONNECTING VIDEO COMPONENTS

• The jacks of VIDEO 1 may also be connected to a DVD recorder or other digital video recording component. For details, refer

to the operating instructions of the component to be connected.

• The jacks of VIDEO 2 can also be connected to an additional video component such as a cable TV tuner, an LD player or

satellite system.

• There are three types of video jacks (COMPONENT, S-VIDEO, (composite) VIDEO) for analog video connections and the HDMI

connectors for digital video and audio connections. Connect them to the corresponding video jacks according to their capability.

• For your reference, the excellence in picture quality is as follows : "HDMI” > "COMPONENT" > "S-VIDEO" > "(composite) VIDEO".

• When making COMPONENT VIDEO connections, connect "Y" to "Y", "PB/CB" to "CB"(or "B-Y", "PB") and "PR/CR" to "CR"(or

"R-Y", "PR").

Note :

• When recording video program sources through VIDEO 1 OUT jacks or viewing video program sources through MONITOR

OUT jack, you must use the same type of video jacks that you did connect to video playback components such as DVD

player, LD player, etc.

HDMI (High Definition Multimedia Interface) connection : (*)

• You can connect the source component (DVD player, etc.) to the display component (TV, projector, etc.) through this receiver

with using a commercially available HDMI cord.

• The HDMI connection can carry uncompressed digital video signals and digital audio signals.

• This receiver can output digital video and digital audio signals from the HDMI MONITOR OUT of this receiver without passing

through any circuits as they were input into the HDMI IN(, meaning the audio signals which are input into the HDMI IN cannot

be reproduced on this receiver).

• This receiver is HDMI Ver. 1.3 compatible.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.

Notes :

• Depending on the connected component, unreliable signal transfer may happen.

(For details, refer to the operating instruction of your component.)

• For stable signal transfer, we recommend using HDMI cords that are a maximum of 5 meters in length.

RD-6513(A) 2008.8.21 12:19 PM 페이지 7

ENGLISH

4. CONNECTING EXTERNAL INs

• Use these jacks to connect the corresponding analog

outputs of 6 CH decoder or DVD player with 6 CH output

for Dolby Digital or DTS, etc.

(For details, see the operator's manual of the component

to be connected.)

3. CONNECTING AUDIO COMPONENTS

• The TAPE IN/OUT jacks can be connected to audio recording equipment such as a tape deck, an MD recorder, etc.

RD-6513(A) 2008.8.21 12:19 PM 페이지 8

ENGLISH

6. CONNECTING SUBWOOFER PRE OUT

• To emphasize the deep bass sounds, connect a powered

subwoofer.

7. CONNECTING SPEAKERS

• Be sure to connect speakers firmly and correctly according to

the channel(left and right) and the polarity(+ and -). If the

connections are faulty, no sound will be heard from the

speakers, and if the polarity of the speaker connection is

incorrect, the sound will be unnatural and lack bass.

• For installing the speakers, refer to "Speaker placement" on

page 10.

• After installing the speakers, first adjust the speaker settings

according to your environment and speaker layout.

(For details, refer to "SETTING THE SPEAKER SETUP" on

page 34.)

Caution :

• Be sure to use the speakers with the impedance of 6 ohms or

above.

• Do not let the bare speaker wires touch each other or any

metal part of this unit. This could damage this unit and/or the

speakers.

5. CONNECTING DIGITAL INs

• The OPTICAL and the COAXIAL DIGITAL OUTs of the

components that are connected to CD and VIDEO 1 ~

VIDEO 2 of this unit can be connected to these DIGITAL

INs.

• A digital input should be connected to the components

such as a CD player, LD player, DVD player, etc. capable

of outputting DTS Digital Surround, Dolby Digital or PCM

format digital signals, etc.

• For details, refer to the operating instructions of the

component connected.

• When making the COAXIAL DIGITAL connection, be sure

to use a 75 ΩCOAXIAL cord, not a conventional AUDIO

cord.

• All of the commercially available optical fiber cords cannot

be used for the equipment. If there is an optical fiber cord

which cannot be connected to your equipment, consult

your dealer or nearest service organization.

Note :

• Be sure to make either a OPTICAL or a COAXIAL DIGITAL connection on each component. (You don’t need to do both.)

RD-6513(A) 2008.8.21 12:19 PM 페이지 9

ENGLISH

Ideal speaker placement varies depending on the size of your

room and the wall coverings, etc. The typical example of

speaker placement and recommendations are as follows :

Front left and right speakers and center speaker

• Place the front speakers with their front surfaces as flush with

TV or monitor screen as possible.

• Place the center speaker between the front left and right

speakers and no further from the listening position than the

front speakers.

• Place each speaker so that sound is aimed at the location of

the listener’s ears when at the main listening position.

Surround left and right speakers

• Place the surround speakers approximately 1 meter (40

inches) above the ear level of a seated listener on the direct

left and right of them or slightly behind.

Subwoofer

• The subwoofer reproduces powerful deep bass sounds.

Place a subwoofer anywhere in the front as

desired.

Notes :

• When using a conventional TV, to avoid interference with the

TV picture, use only magnetically shielded front left and right

and center speakers.

• To obtain the best surround effects, the speakers except the

subwoofer should be full range speakers.

Speaker placement

1. TV or screen

2. Front left speaker

3. Front right speaker

4. Center speaker

5. Subwoofer

6. Surround left speaker

7. Surround right speaker

8. AC INPUT CORD

• Plug the cord into a wall AC outlet.

RD-6513(A) 2008.8.21 12:19 PM 페이지 10

ENGLISH

Front Panel Controls

FLUORESCENT DISPLAY

1. Input, frequency, volume level, operating information, etc.

2. Surround mode indicators

3. AUTO indicator

4. DIGITAL INPUT indicator

5. DIRECT indicator

6. Preset number, sleep time display

7. MEMORY indicator

8. PRESET indicator

9. SLEEP indicator

10. TUNED indicator

11. STEREO indicator

1. POWER switch

2. POWER ON/STANDBY button

3. STANDBY indicator

4. FLUORESCENT DISPLAY

For details, see below.

5. VIDEO INPUT SELECTOR button

6. AUDIO INPUT SELECTOR button

7. EXT.IN SELECTOR button

8. FM/AM button

9. MASTER VOLUME CONTROL knob

10. MULTI CONTROL knob ()

11. HEADPHONE jack

12. SPEAKER button/indicator

13. REMOTE SENSOR

14. SURROUND MODE button

15. STEREO button

16. DISPLAY button

17. DIGITAL/ANALOG MODE button

18. SETUP button

19. CHANNEL LEVEL button

20. CONTROL UP/DOWN ()

buttons

21. MEMORY/ENTER button

22. TUNING UP/DOWN (+/-) buttons

23. PRESET UP/DOWN (+/-) buttons

24. SETUP MIC JACK

For details, see next page.

25. FRONT AUX IN JACK

For details, see next page.

26. Bluetooth IN connector

For details, see next page.

RD-6513(A) 2008.8.21 12:19 PM 페이지 11

ENGLISH

• The FRONT AUX IN jack can be connected to additional audio components such as an MP3 player, etc.

Note :

• When connecting this jack to an MP3 player, etc., you should use the stereo mini cord, not a mono mini cord.

FRONT AUX IN JACK

Microphone

• To use Auto Setup function, connect the supplied microphone to the SETUP MIC jack.(For details, refer to "When

selecting the AUTO SETUP" on page 35.)

Notes:

• Because the microphone for Auto Setup is designed for use with this receiver, do not use a microphone other than

the one supplied with this receiver.

• After you have completed the auto setup procedure, disconnect the microphone.

SETUP MIC JACK

Bluetooth IN CONNECTOR

• If the Bluetooth IN connector is connected to Sherwood Audio Receiver

BT-R7(sold separately) with Bluetooth wireless technology, you can enjoy

music wirelessly with a music player featuring Bluetooth wireless

technology such as MP3 player, mobile phone, etc..

(For information on Sherwood Audio Receiver BT-R7, contact your dealer.)

• The Bluetooth word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc. and any use of such marks by Sherwood Corporation is

under license. Other trademarks and trade names are those of their

respective owners.

Notes:

• For safe operation, turn the power off before connecting or disconnecting

the Audio Receiver BT-R7.

• When not using the Bluetooth IN connector, cover it with the supplied cap.

RD-6513(A) 2008.8.21 12:19 PM 페이지 12

ENGLISH

Remote Controls

Note :

• Some buttons (USB, VIDEO 3, AUX and USB transport buttons) are not available for this receiver.

RD-6513(A) 2008.8.21 12:19 PM 페이지 13

ENGLISH

LOADING BATTERIES

REMOTE CONTROL OPERATION RANGE

• Use the remote control unit within a range of about 7 meters (23

feet) and angles of up to 30 degrees aiming at the remote sensor.

• Remove the batteries when they are not used for a

long time.

• Do not use the rechargeable batteries (Ni-Cd type).

1. Remove the cover. 2. Load two batteries ("AAA" size, 1.5 V) matching the

polarity.

RD-6513(A) 2008.8.21 12:19 PM 페이지 14

ENGLISH

Operations

LISTENING TO A PROGRAM SOURCE

Before operation

• Enter the standby mode.

• The STANDBY indicator lights up.

This means that the receiver is not

disconnected from the AC mains and a

small amount of current is retained to

support the operation readiness.

• To switch the power off, push the POWER

switch again.

• Then the power is cut off and the STANDBY

indicator goes off.

• Each time the POWER ON/STANDBY button on the front

panel is pressed, the receiver is turned on to enter the

operating mode or off to enter the standby mode.

• On the remote control, press the POWER ON button to

enter the operating mode or press the STANDBY button

to enter the standby mode.

• In the standby mode, if the INPUT SELECTOR button is

pressed, the receiver is turned on automatically and the

desired input is selected.

• Each time the "VIDEO" button on the front panel is

pressed, the input source changes as follows:

VIDEO 1 VIDEO 2

• Each time the "AUDIO" button on the front panel is

pressed, the input source changes as follows:

CD F AUX TAPE BT IN

• Each time the "FM/AM" button is pressed, the band

changes as follows:

FM ST FM MONO AM

When selecting the EXTERNAL IN as desired

• "EXT IN" is displayed and 6 seperate analog signals

from the component connected to this input pass

through the tone and volume circuits only and can be

heard from your speakers.

• Selecting the desired input source to cancel the external

in function.

• These analog signals can be heard only, not recorded.

POWER

1. In the standby mode, turn the power on.

• Then the SPEAKER indicator lights up and the sound

can be heard from the speakers connected to the

speaker terminals.

• When using the headphone for private listening, press

the SPEAKER button again to switch the speakers off.

2. Switch the speakers on.

3. Select the desired input source.

Note : Before operating this receiver, first set this unit as desired for optimum performance, doing the system setup

procedures. (For details, refer to "System Setup" on page 29.)

RD-6513(A) 2008.8.21 12:19 PM 페이지 15

ENGLISH

When CD, VIDEO 1~ 2 is selected as an input source

• When playing back the program sources with surround

sound, refer to “ENJOYING SURROUND SOUND” on

page 19.

• Each time this button is pressed, the corresponding input

is selected as follows:

o(ptical) c(oaxial)1c(oaxial) 2 A(nalog)

Notes :

• When F AUX, TAPE, BT IN, EXT IN or tuner is selected as

an input source, the digital input cannot be selected.

• When the selected digital input is not connected, the

"DIGITAL" indicator flickers and the analog input is

automatically selected.

• The selected digital or analog input is automatically

assigned to the corresponding input source on the INPUT

setup menu. (For details, refer to "SETTING THE INPUT "

on page 33.)

• The sound from the component connected to the selected

digital input can be heard regardless of the selected input

source.

• “MUTE” will flicker.

• To resume the previous sound level, press it again.

DOWN UP

4. Select the digital or the analog input connected

as desired.

7. To mute the sound.

5. Operate the selected component for playback.

6. Adjust the (overall) volume.

• Be sure to switch the speakers off.

• When listening to a DTS or Dolby Digital program source,

if the headphones are plugged in and the SPEAKER

button is set to off, it enters the 2CH downmix mode

automatically. (For details, refer to "2CH downmix mode"

on page 19.)

Note :

• Be careful not to set the volume too high when using

headphones.

8. To listen with the headphones.

RD-6513(A) 2008.8.21 12:19 PM 페이지 16

ENGLISH

• Each time these buttons are pressed, the tone mode is

selected as follows :

OFF : To listen to a program source without the tone

effect. ("DIR" indicator lights up.)

ON : To adjust the tone for your taste.

("DIR" indicator goes off.)

Note :

• When the EXTERNAL IN is selected as an input source,

the TONE cannot be set to ON.

• Each time these buttons are pressed, the tone is

selected as follows :

BASS TRBL (treble) TONE : ON 

When the TONE is set to ON to adjust the tone

(bass and treble).

• The tone level can be adjusted within the range of -10 ~

+10 dB.

• In general, we recommend the bass and treble to be

adjusted to 0 dB (flat level).

• Extreme settings at high volume may damage your

speakers.

• To complete tone adjustment, repeat the above steps 11

and 12.

• If the tone display disappears, start from the step 9 again.

11. Press the CURSOR UP()/DOWN()

buttons to select the desired tone.

12. Press the CURSOR LEFT()/RIGHT()

buttons to adjust the selected tone as desired.

10. Press the CURSOR LEFT()/RIGHT()

buttons to select the desired tone mode.

Adjusting the tone (bass and treble)

9. Enter the tone mode.

• The tone mode is displayed for several seconds.



RD-6513(A) 2008.8.21 12:19 PM 페이지 17

ENGLISH

SURROUND SOUND

• This receiver incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound

atmosphere in your personal Home Theater.

DTS Digital Surround

DTS Digital Surround(also called simply DTS) is a multi-

channel digital signal format which can handle higher data

rates. Discs bearing the DTS logo include the recording of

up to 5.1 channels of digital signals, which can be generally

thought to provide better sound quality due to the lower

audio compression required.

It also provides wide dynamic range and separation,

resulting in magnificent sound.

DTS 96/24

This is high resolution DTS with a 96 kHz sampling rate

and 24 bit resolution, providing superior fidelity. Use it with

DVDs bearing the DTS 96/24 logo.

Manufactured under license under U.S. Patent #'s: 5,451,942;

5,956,674; 5,974,380; 5,978,762; 6,226, 616; 6,487,535 & other U.S.

and worldwide patents issued & pending. DTS and DTS Digital

Surround are registered trademarks and the DTS logos , Symbol and

DTS 96/24 are trademarks of DTS, Inc. 1996-2007 DTS, Inc. All

Rights Reserved.

Dolby Digital

Dolby Digital is the multi-channel digital signal format

developed by Dolby Laboratories. Discs bearing the Dolby

Digital logo includes the recording of up to 5.1 channels of

digital signals, which can reproduce much better sound

quality, spatial expansion and dynamic range

characteristics than the previous Dolby Surround effect.

Dolby Pro Logic II surround

This mode applies conventional 2-channel signals such as

digital PCM or analog stereo signals as well as Dolby

Surround signals, etc. to surround processing to offer

improvements over conventional Dolby Pro Logic circuits.

Dolby Pro Logic ll surround includes 3 modes as follows:

• Dolby Pro Logic ll Movie

When enjoying movies, this mode allows you to further

enhance the cinematic quality by adding processing that

emphasizes the sounds of the action special effects.

• Dolby Pro Logic ll Music

When listening to music, this mode allows you to further

enhance the sound quality by adding processing that

emphasizes the musical effects.

• Dolby Pro Logic ll Emulation

This mode expands any 2-channel sources(, including

Dolby Surround sources) for 4 channel(front left, center,

front right and surround) playback.

The surround channel is monaural, but is played through

two surround speakers.

Dolby, Pro Logic, and the double-D symbol are registered

trademarks of Dolby Laboratories.

• The following modes apply conventional 2-channel

signals such as digital PCM or analog stereo signals to

high performance Digital Signal Processor to recreate

sound fields artificially.

Theater

This mode provides the effect of being in a theater-in-the

round when watching a play.

Movie

This mode provides the effect of being in a movie theater

when watching a movie.

Hall 1/2

This mode provides the ambience of a chamber hall for

chamber music or an instrumental solo(Hall 1) or concert

hall for orchestral music or an opera (Hall 2).

Stadium

This mode provides the expansive sound field to achieve

the true stadium effect when watching baseball or soccer

games.

Church

This mode provides the ambience of a church for baroque,

string orchestral or choral group music.

Club 1/2

This mode creates the sound field of a jazz club with a low

ceiling and hard walls (Club 1) or a live house with a

relatively spacious floor (Club 2).

Arena 1/2

This mode provides a feeling of a live concert in a medium

sized (Arena 1) or large (Arena 2) arena.

Game

Use this mode to enjoy video game sources.

Matrix

This mode reproduces a delayed signals from the surround

channels to emphasize the sense of expansion for music

sources.

Surround modes

• When the EXTERNAL INs is connected to the 6CH decoder for a surround such as Dolby Digital, etc., you can enjoy the

corresponding surround sound, too. (For details, see th operator's manual of the component to be connected.)

RD-6513(A) 2008.8.21 12:19 PM 페이지 18

ENGLISH

ENJOYING SURROUND SOUND

Notes:

• Before surround playback, first perform the speaker setup procedure, etc. on the SETUP menu for optimum performance. (For

details, refer to "SETTING THE SPEAKER SETUP" on page 34.)

• When the EXTERNAL IN is selected as an input source, the surround modes cannot be selected.

When CD or VIDEO 1 ~ 2 is selected as an input source

• Depending on the signal format which is being input,

either the stereo mode or the 2CH downmix mode is

selected.

• To cancel either the stereo mode or the 2CH downmix

mode, select the surround mode with using the MULTI

CONTROL knob on the front panel or the SURROUND

MODE UP/DOWN (>/<)buttons on the remote control.

Signal format being input

Dolby Digital 5.1 channel sources

Dolby Digital 2 channel sources

DTS sources, DTS 96/24 sources

96 kHz PCM(2 channel) sources

PCM (2channel) sources,

Analog stereo sources

Selectable surround mode

DOLBY DIGITAL

DOLBY PLII MOVIE, DOLBY PLII MUSIC, DOLBY PLII EMULATION

DTS or DTS 96/24

DOLBY PLII MOVIE, DOLBY PLII MUSIC, DOLBY PLII EMULATION

DOLBY PLII MOVIE, DOLBY PLII MUSIC, DOLBY PLII EMULATION, THEATER, MOVIE, HALL1,

HALL2, STADIUM, CHURCH, CLUB1, CLUB2, ARENA1, ARENA2, GAME, MATRIX

To cancel the surround mode for stereo playback

2CH downmix mode

• This mode allows the multi-channel signals encoded in DTS or Dolby Digital format to be mixed down into 2 front channels

and to be reproduced through only two front speakers or through headphones.

• When the SPEAKER button is set to off to listen with headphones while playing the multi-channel digital signals from DTS or

Dolby Digital sources, it will enter the 2CH downmix mode automatically.

Select the auto surround mode or the manual surround mode depending on how to select a surround mode.

• Each time this button is pressed, the mode changes as follows :

Auto surround mode : The optimum surround mode will be automatically

selected depending on the signal format being input.

Manual surround mode : You can select the desired of different surround

modes selectable for the signal being input with

using the MULTI CONTROL knob or the

SURROUND MODE UP/DOWN () buttons.

("AUTO" indicator

lights up.)

("AUTO" indicator

goes off.)

Notes :

• When the input source other than CD and VIDEO 1 ~ 2 is selected, you cannot select the auto surround mode and can select

the surround mode as desired (the manual surround mode).

• When the auto surround mode is selected, the surround modes other than the optimum surround mode cannot be selected.

Select the desired surround mode (when selecting the manual surround mode in case of CD, VIDEO 1 ~ 2)

• Each time the MULTI CONTROL knob is rotated or the

SURROUND UP / DOWN () buttons are pressed,

the surround mode changes depending on the input

signal format as follows :

RD-6513(A) 2008.8.21 12:19 PM 페이지 19

ENGLISH

• While playing digital signals from Dolby Digital or DTS program source or listening in Dolby Pro Logic II Music mode, you

can adjust their parameters for optimum surround effect.

• Then "DRC : ~ " (or "PANO : ~ ") is displayed for several seconds.

• If the parameter mode disappears, press this button again.

When adjusting the sound parameters

1. Press the SOUND PARAMETER button.

2. Press the CURSOR UP()/DOWN() buttons to select the desired parameter.

When selecting the "DRC(Dynamic Range Compression:

Night mode)"

This function compresses the dynamic range of previously specified

parts of Dolby Digital or DTS sound track (with extremely high volume)

to minimize the difference in volume between the specified and non-

specified parts. This makes it easy to hear all of the sound track when

watching movies at night at low levels. The night mode can be set to

OFF or ON (default value : OFF).

Note : In some Dolby Digital or DTS softwares, the night mode may

not be valid.

When selecting the "PANO (Panorama)" mode

This mode extends the front stereo image to include the surround

speakers for an exciting "wraparound" effect with side wall imaging.

Select "OFF" or "ON"(default value: OFF).

When selecting the "C. WIDTH (Center width)" control

This adjusts the center image so it may be heard only from the center

speaker, only from the left/right speakers as a phantom image, or from

all three front speakers to varying degrees.

The control can be set in 8 steps from 0 to 7(default value : 3).

When selecting the "DIMEN (Dimension)" control

This gradually adjusts the soundfield either towards the front or

towards the rear. The control can be set in 7 steps from -3 to +3

(default value : 0).

3. Press the CURSOR LEFT()/ RIGHT() buttons to adjust the selected parameter as desired.

4. Repeat the above steps 2 and 3 to adjust other parameters.

• Each time these buttons are pressed, the parameter mode

changes as follows:

"DRC" "PANO" "C.WIDTH" "DIMEN" 

(Dynamic Range Compression) (Panorama mode) (Center width control) (Dimension control)

• "DRC" can be selected only while playing digital signals from

Dolby Digital or DTS source.

• "PANO", "C.WIDTH" and "DIMEN" can be selected only while

listening in Dolby Pro Logic II Music mode.

RD-6513(A) 2008.8.21 12:19 PM 페이지 20

ENGLISH

• The volume level of each channel can be adjusted easily with the test tone function.

Note : When the SPEAKER button is set to off, the test tone function does not work.

Adjusting each channel level with test tone

• The test tone mode is displayed and will be heard from

the speaker of each channel for 2 seconds as follows:

FL C FR SR SL SW

Front Left Center Front Right Surround Right Surround Left Subwoofer

• When the speaker setting is "N (None or No)", the test

tone of the corresponding channel is not available.

1. Enter the test tone mode.

2. At each channel, adjust the level as desired until the sound level of each speaker is heard to be equally loud.

3. Cancel the test tone function.

• You can select the desired channel with the CONTROL

UP()/DOWN() buttons or the CURSOR UP()/

DOWN() buttons.

RD-6513(A) 2008.8.21 12:19 PM 페이지 21

ENGLISH

Adjusting the current channel level

• Each time these buttons are pressed, the corresponding

channel is selected as follows:

REF 1, 2 (or CAL) FL C FR 

<DTS or DD> SW SL SR 

< >: Only when the digital signals from Dolby Digital or DTS

program sources that include LFE signal are input, LFE level

can be displayed.

• Depending on the speaker settings ("N (None or No)") and

surround mode, etc., some channels cannot be selected.

• When the SPEAKER button is set to off, only the Front

Left and Front Right channels can be selected.

• After adjusting each channel level with test tone, adjust the channel levels either according to the program sources or to suit

your tastes.

• You can adjust the current channel levels as desired. These adjusted levels are just memorized into user’s memory ("CAL"),

not into preset memory("REF 1", "REF 2").

• The LFE level can be adjusted within the range of -10~0

dB and other channel levels within the range of -15 ~ +15

dB.

• In general, we recommend the LFE level to be adjusted

to 0 dB. (However, the recommended LFE level for some

early DTS software is -10 dB.) If the recommended levels

seem too high, lower the setting as necessary.

• Then the memory mode ("REF 1", etc.) is displayed for

several seconds.

• When the memory mode or channel level disappears,

press this button again.

1. Press the CHANNEL LEVEL button.

2. Select the desired channel.

3. Adjust the level of the selected channel as desired.

4. Repeat the above steps 2 and 3 to adjust each channel level.

RD-6513(A) 2008.8.21 12:19 PM 페이지 22

ENGLISH

Memorizing the adjusted channel levels

• Then "1" of "REF 1" indication flickers for several

seconds.

• You can memorize the adjusted channel levels into preset memory("REF 1", "REF 2") and recall the memorized whenever you

want.

• "CAL " (or "REF 1", etc.) is displayed for several

seconds.

• If the channel level mode display disappears, press this

button again.

• The adjusted channel levels have now been memorized

into the selected memory.

• If the preset memory disappears, perform the above

step 1 again.

1. After performing the steps 1 ~ 4 in "Adjusting the current channel level" procedure on page 22, press the

(MEMORY/)ENTER button.

Recalling the memorized channel levels

• Then the channel levels memorized into the selected

preset memory are recalled.

2. Select the desired one of REF 1 and REF 2.

3. Confirm your selection.

1. Press the CHANNEL LEVEL button.

2. Select the desired one of REF 1 and REF 2.

RD-6513(A) 2008.8.21 12:19 PM 페이지 23

ENGLISH

LISTENING TO RADIO BROADCASTS

Auto tuning

• Each time this button is pressed, the band changes as

follows ;

FM ST FM MONO AM

("ST" lights up) ("ST" goes off)

• When FM stereo broadcasts are poor because of weak

broadcast signals, select the FM mono mode to reduce

the noise, then FM broadcasts are reproduced in

monaural sound.

• Manual tuning is useful when you already know the

frequency of the desired station.

• After selecting the desired band, press the TUNING

UP(+) / DOWN(-) buttons repeatedly until the right

frequency has been reached.

Manual tuning

• The tuner will now search until a station of sufficient

strength has been found. The display shows the tuned

frequency and "TUNE".

• If the station found is not the desired one, simply repeat

this operation.

• Weak stations are skipped during auto tuning.

1. Select the desired band.

2. Press the TUNING UP(+)/DOWN(-) buttons for

more than 0.5 second.

Auto presetting

• Auto presetting function automatically searches for FM

stations only and store them in the memory.

• While listening to FM radio broadcasts, press and hold

down the (MEMORY/) ENTER button for more than 2

seconds.

• Then "AUTO MEM" flickers and this receiver starts auto

presetting.

• To stop auto presetting, press this button again.

• Up to 30 FM stations can be stored.

Notes:

• FM stations of weak strength cannot be memorized.

• To memorize AM stations or weak stations, preform

"Manual presetting" procedure with using "Manual

tuning" operation.

RD-6513(A) 2008.8.21 12:19 PM 페이지 24

ENGLISH

• When using the NUMERIC buttons on the remote control.

Examples) For “3” :

For “15” :

For “30” :

Tuning to preset stations

3. Select the desired preset number (1~30) and

press the (MEMORY/)ENTER button.

4. Repeat the above steps1 to 3 to memorize other

stations.

MEMORY BACKUP FUNCTION

The following items, set before the receiver is turned off,

are memorized.

• INPUT SELECTOR settings

• Surround mode settings

• Preset stations,etc.

• When using the NUMERIC buttons on the remote

control.

Examples) For “3” :

For “15” :

For “30” :

• The station has now been stored in the memory.

• When using the NUMERIC buttons, the station is stored

automatically without pressing the (MEMORY/)ENTER

button.

• A stored frequency is erased from the memory by

storing another frequency in its place.

• If “MEM” goes off, start again from the above step 2.

• After selecting the tuner as an input source, select the

desired preset number.

Manual presetting

• You can store up to 30 preferred stations in the memory.

• "MEM" is flickering for several seconds.

1. Tune in the desired station with auto or manual

tuning.

2. Press the (MEMORY/)ENTER button.

MEM

RD-6513(A) 2008.8.21 12:19 PM 페이지 25

ENGLISH

RECORDING

Recording with TAPE

Dubbing from video components onto VIDEO 1

• The analog signals from the EXTERNAL INs as well as the digital signals from the coaxial or optical digital input can be

heard but cannot be recorded.

• When recording the analog signals from CD, VIDEO 1 ~ 2, be sure to select th analog input.

(For details, refer to "When CD, VIDEO 1 ~ 2 is selected as an input source" on page 16.)

• The volume and tone (bass, treble) settings have no effect on the recording signals.

• The audio and video signals from the VIDEO 2 will be dubbed onto the VIDEO 1 and you can enjoy them on the TV set and

from the speakers.

1. Select the desired input as a recording source except for TAPE.

1. Select VIDEO 2 as a recording source.

2. Start recording on the TAPE.

2. Start recording on the VIDEO 1.

3. Start play on the VIDEO 2.

3. Start play on the desired input.

RD-6513(A) 2008.8.21 12:19 PM 페이지 26

ENGLISH

Dubbing the audio and video signals separately onto VIDEO 1

Example) When dubbing the VIDEO 2 video signal and the CD audio signal separately onto VIDEO 1.

1. Select VIDEO 2 as a video recording source.

2. Select CD as an audio recording source.

3. Start recording on the VIDEO 1.

• The audio signal from the CD and the video signal from the VIDEO 2 will be dubbed and you can enjoy them on the TV set

and from the speakers.

Note :

• Be sure to observe the order of the above steps 1 and 2.

4. Start play on the VIDEO 2 and the CD respectively.

RD-6513(A) 2008.8.21 12:19 PM 페이지 27

ENGLISH

Operating the sleep timer

• The sleep timer allows the system to continue to operate for a specified period of time before automatically shutting off.

• To set the receiver to automatically turn off after the specified period of time.

Adjusting the brightness of the fluorescent display

OTHER FUNCTIONS

• Each time this button is pressed, the display mode

changes as follows:

• When the EXTERNAL IN is selected as an input source,

the surround mode is not displayed.

Displaying the operation status

Surround

mode Volume Input

source



• Each time this button is pressed, the sleep time changes

as follows:

10 20 30 --- 90 OFF

Unit : minutes

• While operating the sleep timer, " " lights up.

• When the sleep time is selected, the fluorescent display

is dimly lit.

• Each time this button is pressed, the brightness of

the fluorescent display changes as follows:

ON dimmer OFF

• In the display OFF mode, pressing any button will

restore the display ON mode.

During playback,

RD-6513(A) 2008.8.21 12:19 PM 페이지 28

ENGLISH

System Setup

• The setup menu is displayed on the fluorescent display and allows you to perform the setup procedures easily. In most situations,

you will only need to set this once during the installation and layout of your home theater, and it rarely needs to be changed later.

The setup menu consists of 5 main menus ; system, input, speaker setup, CH level and parameter. These menus are then divided

up into various sub-menus.

Navigating through the setup menu

• The explanations here assume you are using the buttons on the remote control when performing the setup menu operation.

However, you can use the buttons on the front panel as well.

The buttons on the front panel correspond to those on the remote control as shown below.

• The setup menu will be shown.

• To turn the menu off, press this button again.

• When selecting "SYSTEM", see "SETTING THE

SYSTEM" on page 31.

• When selecting "INPUT", see "SETTING THE

INPUT" on page 33.

• When selecting "SPK SET", see "SETTING THE

SPEAKER SETUP" on page 34.

• When selecting "CH LEVEL", see "SETTING

THE CH LEVEL" on page 39.

• When selecting "PARAMTR", see "SETTING

THE PARAMETER" on page 41.

• When selecting "EXIT", the setup menu will be

turned off.

1. Turn the setup menu on.

3. Confirm your selection.

2. Select the desired menu using the CURSOR UP()/DOWN() buttons.

RD-6513(A) 2008.8.21 12:19 PM 페이지 29

ENGLISH

Setup menu flow

• The setup menu flow is as follows :

• When "RETURN" is selected on a sub-menu, it will return to the previous menu.

Note :

• During setup menu operation, only the (POWER ON/) STANDBY button and the buttons required for system setup will

function.

RD-6513(A) 2008.8.21 12:19 PM 페이지 30

ENGLISH

SETTING THE SYSTEM

When selecting the SUBWOOFER mode

1. Press CURSOR UP()/DOWN() buttons to select the desired item.

2. Press the CURSOR LEFT()/RIGHT() buttons to set the selected item as desired.

• "SW "mode is effective only when "FRONT", "CENTER" or "SURR" is set to "L" and "SUB- W" is set to "Y" on the SPK

SET menu. (For details, refer to "SETTING THE SPEAKER SETUP" on page 34.)

NORM : When the low frequency signals of channels set to "L" are reproduced from those channels only.

In this mode, the low frequency signals that are reproduced from the subwoofer channel is only the low frequency

signals of LFE (from the multi-channel sources that contains LFE (Low Frequency Effects) channel, also called the

".1" channel) and the channels set to "S".

SW : When the low frequency signals of channels set to "L" are reproduced simultaneously from those channels and the

subwoofer channel.

In this mode, the low frequency range expands more uniformly through the room, but depending on the size and

shape of the room, interference may result in a decrease of the actual volume of the low frequency range.

• SW (SUBWOOFER) : To select the desired subwoofer mode.

• TONE : To adjust the tone (bass and treble) as desired.

• RMEQ (ROOM EQ) : To select the desired room EQ mode.

• RETURN : To return to the previous menu.

RD-6513(A) 2008.8.21 12:20 PM 페이지 31

ENGLISH

OFF : To listen to a program source without the tone effect. ("DIR" indicator lights up.)



ON : To adjust the tone for your taste. ("DIR" indicator goes off.)

Note :

• When the EXTERNAL IN is selected as an input source, the TONE cannot be set to ON.

When the TONE is set to ON to adjust the tone (bass and treble)



Press the ENTER button to enter the tone adjustment.



Press the CURSOR UP()/DOWN() buttons to select the desired tone.

• The tone level can be adjusted within the range of -10 ~ +10 dB.

• In general, we recommend the bass and treble to be adjusted to 0

dB (flat level).

• Extreme settings at high volume may damage your speakers.

• To complete tone adjustment, repeat the above steps



and



Press the CURSOR LEFT()/RIGHT() buttons to adjust the selected tone as desired.

When selecting the TONE

When selecting the ROOM EQ mode

• The room EQ is a kind of room equalizer for your speakers. According to the acoustic characteristics of your room

measured by the auto setup, the room EQ automatically adjusts the frequency response of your speakers.

• If you use different brands or sizes of speakers for some channels or have a room with unique acoustic characteristics,

such as walls, furniture, and the dimensions or the shape of the room, we recommend using the room EQ.

Note :

• When playing the 96 kHz PCM (2 channel) digital signals, the room EQ is invalid.

OFF : When turning off the room EQ.



ON (AUTO SET) : To adjust the frequency response of all speakers to the flattest response.

• If you have never performed the auto setup, it will automatically enter the auto setup mode to measure

the acoustic characteristics of your room. In this case, you should perform the auto setup to set the

ROOM EQ to ON. (For details, refer to "When selecting the AUTO SETUP" on page 35.)

RD-6513(A) 2008.8.21 12:20 PM 페이지 32

ENGLISH

3. Press the CURSOR LEFT()/RIGHT() buttons to set the selected item as desired.

2. Press the CURSOR UP()/DOWN() buttons to select the desired item.

1. Press the CURSOR UP()/DOWN() buttons to select the desired input source, then press the ENTER

button.

Example) When selecting the VIDEO 2

SETTING THE INPUT

• D.IN (DIGITAL IN) : To assign the connected DIGITAL INs to the desired input.

• AUTO (AUTO SURROUND) : To select the auto surround mode or the manual surround mode.

• RETURN : To return to the previous menu.

RD-6513(A) 2008.8.21 12:20 PM 페이지 33

ENGLISH

SETTING THE SPEAKER SETUP

• After you have installed this receiver and connected all the components, you should adjust the speaker settings for the

optimum sound acoustics according to your environment and speaker layout.

• Even when you change speakers, speaker positions, or the layout of your listening environment, you should adjust the

speaker settings, too.

• When performing the AUTO SETUP precedure, you need not perform the CONFIGURATION, DISTANCE and CH LEVEL

setup procedures.

• AUTO SET (AUTO SETUP) : To set the speaker setup and channel level setup automatically.

• CONFIG (CONFIGURATION) : To select the sizes of the speakers that are connected.

• DISTANCE: To enter the distance between the listening position and each speaker to set the delay time automatically for

optimum surround playback.

• X-OVER (CROSSOVER) : To select the desired crossover frequency.

• RETURN : To return to the previous menu.

• You should assign the connected DIGITAL INs to the desired of CD and VIDEO 1 ~ VIDEO 2.

(For details, refer to "CONNECTING DIGITAL INs" on page 9.)

• You can select the desired of OPT (optical), COX 1(coaxial 1), COX 2(coaxial 2) and ANL (analog).

Note :

• In such a case that a DIGITAL IN is assigned to two input sources or more, when these input sources are selected, the digital

audio signals can be heard from the same DIGITAL IN.

When selecting the DIGITAL IN

• Depending on how to select a surround mode, you can select the auto surround mode or the manual surround mode.

OFF : You can select the desired of different surround modes selectable for the signal being input with

(Manual surround mode) using the MULTI CONTROL knob or the SURROUND MODE UP/DOWN (>/<) buttons.

(For details, refer to "ENJOYING SURROUND SOUND" on page 19.)

ON : The optimum surround mode will be automatically selected depending on the signal format being

(Auto surround mode) input.

Notes :

• When the input source other than CD and VIDEO 1 ~ 2 is selected, you cannot select the auto surround mode and can

select the surround mode as desired(the manual surround mode).

• When the auto surround mode is selected, the surround modes other than the optimum surround mode cannot be selected.

When selecting the AUTO SURROUND

RD-6513(A) 2008.8.21 12:20 PM 페이지 34

ENGLISH

When selecting the AUTO SETUP

• Auto Setup lets you avoid troublesome listening-based speaker setup and achieve good surround sound.

You should connect the supplied microphone to the SETUP MIC jack so that this receiver can analyze the information from a

series of test tones emitted from speakers and can adjust the configuration, distance, sound level and frequency response of

each speaker automatically.

• If you want to personalize your speaker setup and channel level setup by making the settings manually, perform "When

selecting the CONFIGURATION" on page 36, "When selecting the DISTANCE" on page 37, "When selecting the

CROSSOVER" on page 38, "Adjusting each channel level with test tone" on page 21 and "Adjusting the current channel level"

on page 22.

• After the auto setup has been completed, the ROOM EQ is automatically set to ON. (For details, refer to "When selecting the

ROOM EQ mode" on page 32.)

Preparations

. Check that the speakers are securely connected to this receiver.

• If your subwoofer has adjustable volume and crossover frequency, set the volume halfway and set the crossover frequency

to the maximum or the low pass filter off.

. Connect the supplied microphone to the SETUP MIC jack on the front panel.(For details, refer to "SETUP MIC JACK" on

page 12 .)

Notes :

• Because the microphone for Auto Setup is designed for use with this receiver, to use the auto setup function, do not use a

microphone other than the one supplied with this receiver.

• After you have completed the auto setup procedure, disconnect the microphone.

• If possible, use a tripod, etc. to attach the microphone at the same height as your ears would be when you are seated in your

listening position.

• Ensure there are no obstacles between the speakers and the microphone.

1. Place the microphone on a flat level surface at the listening position.

• Loud test tones are output from each speaker and then if the auto speaker setup procedure has been completed and the

results are memorized, the "AUTO SET" will be displayed.

• Check the results on each setup menu(CONFIGURATION menu on page 36, DISTANCE menu on page 37, and CH

LEVEL menu for "REF 1" mode on page 39.)

• If the results are not satisfactory, you can retry the auto setup precedure or personalize your speaker setup and channel

level setup by making the settings manually.

• To stop the auto setup procedure while outputting the test tones, press the ENTER button.

• If there may be a problem with speaker or microphone connection, "ERROR" will be displayed. In this case, turn off the power,

check the connection and then retry the auto setup procedure.

Notes :

• Because the test tones are loud, ensure there no infants or small children in the room.

• For best results, ensure the room is as quiet as possible during the auto setup procedure.

If there is too much ambient noise, the results may not be satisfactory.

2. Press the CURSOR UP()/DOWN() buttons to select the "AUTO SET", then press the ENTER button.

RD-6513(A) 2008.8.21 12:20 PM 페이지 35

ENGLISH

• Depending on your speaker type, you can select one of these

following speaker types.

L(Large): Select this when connecting speakers that can fully

reproduce sounds below crossover frequency.

S(Small) : Select this when connecting speakers that can not fully

reproduce sounds below crossover frequency. When

this is selected, sounds below crossover frequency are

sent to the subwoofer or speakers which are set to "L

(Large)" (when not using a subwoofer)

N(None): Select this when no speakers are connected. When this

is selected, sounds are sent to the speakers which are

not set to "N (None)".

Y(Yes)/N(No): Select the desired depending on whether a

subwoofer is connected or not.

3. Press the CURSOR LEFT()/ RIGHT() buttons to set the selected speaker as desired.

4. Repeat the above steps 2 and 3 until the speakers are all set to the desired mode.

2. Press the CURSOR UP()/DOWN() buttons to select the desired speaker.

When selecting the CONFIGURATION

1. Press the CURSOR UP()/DOWN() buttons to select the "CONFIG", then press the ENTER button.

Notes :

• When speakers are set to "S (Small)", you should set their crossover frequency correctly according to their frequency

characteristics. (For details, refer to "When selecting the CROSSOVER" on page 38.)

• When "SUB-W" is set to "N (No)", "FRONT" is automatically set to "L (Large)".

• When the "FRONT" is set to "S (Small)", "CENTER" and "SURR" cannot be set to "L (Large)".

About the speaker size

• Select "L (Large)" or "S (Small)" not according to the actual size of the speaker but according to the speaker's capacity for

playing low frequency (bass sound below frequency set on the "X-OVER" menu) signals.

• If you do not know, try comparing the sound at both settings (setting the volume to a level low enough so as not to damage

the speakers) to determine the proper setting.

RD-6513(A) 2008.8.21 12:20 PM 페이지 36

ENGLISH

• You can set the distance within the range of 1 ~ 30 feet

in 1 feet intervals.

When selecting the DISTANCE

Note :

• You cannot select the speakers set to "N (None)" and

the subwoofer.

1. Press the CURSOR UP()/DOWN() buttons to select the DISTANCE, then press the ENTER button.

2. Press the CURSOR UP()/DOWN() buttons to select the desired speaker.

3. Press the CURSOR LEFT()/RIGHT() buttons to set the selected speker as desired.

4. Repeat the above steps 2 and 3 until the distances are all set as desired.

About the speaker distance

When enjoying multi-channel surround playback with Dolby Digital and DTS sources, etc., it is ideal that the center and surround

speakers should be the same distance from the main listening position as the front speakers. By entering the distance between

the listening position and each speaker, the delay times of center and surround speakers are automatically adjusted to create an

ideal listening environment virtually as if the center and surround speakers were at their ideal locations respectively.

RD-6513(A) 2008.8.21 12:20 PM 페이지 37

ENGLISH

About the crossover frequency

• When speakers are set to "S (Small)", low frequencies in those channels that are below the crossover frequency are to

output from subwoofer or front speakers which are set to "L (Large)" (when not using a subwoofer).

• Refer to the operating instructions of the speakers to be connected. If the frequency range of your speaker is 100 Hz~20

kHz, the crossover frequency should be set to 100 Hz(or slightly higher).

When selecting the CROSSOVER

• When speakers are set to "S (Small)", be sure to set their crossover frequency correctly according to their frequency

characteristics.

1. Press the CURSOR UP()/DOWN() buttons to select the "X-OVER", then press the ENTER button.

2. Press the CURSOR LEFT()/RIGHT() buttons to set the crossover frequency as desired.

• You can adjust the crossover frequency within the

range of 40 ~ 130 Hz in 10 Hz intervals.

RD-6513(A) 2008.8.21 12:20 PM 페이지 38

ENGLISH

SETTING THE CH LEVEL

Note : Depending on the speaker settings ("N (None or No)"), some channels cannot be selected.

• The LFE level can be adjusted within the range of -10 ~ 0

dB and other channel levels within the range of -15 ~ +15 dB

• In general, we recommend the LFE level to be adjusted to

0 dB. (However, the rcommended LFE level for some

early DTS software is -10 dB.) If the recommended levels

seem too high, lower setting as necessary.

1. Press the CURSOR UP()/DOWN() buttons to select the desired channel.

2. Press the CURSOR LEFT()/RIGHT() buttons to adjust the level of the selected channel or program

source's LFE as desired.

3. Repeat the above steps 1 and 2 to adjust each channel level.

• You can adjust the current channel levels as desired. These adjusted levels are just memorized into user’s memory("CAL"),

not into preset memory ("REF 1", "REF 2")

• After adjusting each channel level with test tone, adjust the channel levels either according to the program sources or to suit

your tastes. (For details, refer to "Adjusting each channel level with test tone" on page 21.)

Adjusting the current channel level

Example) When selecting Dolby Digital source's LFE

RD-6513(A) 2008.8.21 12:20 PM 페이지 39

ENGLISH

Memorizing the adjusted channel levels

• You can memorize the adjusted channel levels into preset memory("REF 1", "REF 2") and recall the memorized whenever

you want.

• Then "1" of "REF 1" indication flickers.

• Each time the CURSOR LEFT() or RIGHT() button

is pressed, "REF 1" or "REF 2" is selected.

• The adjusted channel levels have now been memorized

into the selected memory.

• "CAL" may be displayed instead of "REF 1" or "REF 2".

• Then the channel levels memorized into the selected

preset memory are recalled.

Recalling the memorized channel levels

1. After performing the steps 1 ~ 3 in "Adjusting the current channel level" procedure on page 39, press the

ENTER button.

2. Press the CURSOR LEFT()/RIGHT() buttons to select the desired preset memory, then press the

ENTER button.

1. Press the CURSOR UP()/DOWN() buttons to select the "MODE ~ ".

2. Press the CURSOR LEFT()/RIGHT() buttons to select the desired one of REF 1 and REF 2.

RD-6513(A) 2008.8.21 12:20 PM 페이지 40

ENGLISH

SETTING THE PARAMETER

When selecting the NIGHT MODE

• This function compresses the dynamic range of previously specified parts of Dolby Digital or DTS sound track (with

extremely high volume) to minimize the difference in volume between the specified and non-specified parts.

This makes it easy to hear all of the sound track when watching movies at night at low levels.

Notes:

• The night mode setting is valid only when the digital signals from Dolby Digital or DTS program source are being input.

• In some Dolby Digital or DTS softwares, the night mode setting may not be valid.

• NIGHT M (NIGHT MODE) : To adjust the dynamic range compression that makes faint sound easier to hear at low volume

levels.

• PLII MSC (DOLBY PLII MUSIC) : To adjust the various surround parameters for optimum surround effect.

• RETURN : To return to the previous menu.

1. Press the CURSOR UP()/DOWN() buttons to select the "NIGHT M", then press the ENTER button.

2. Press the CURSOR LEFT()/ RIGHT() buttons to set the night mode as desired.

OFF : To turn off the night mode function.

↕

ON : To turn it on.

RD-6513(A) 2008.8.21 12:20 PM 페이지 41

ENGLISH

When selecting the DOLBY PLII MUSIC

• You can adjust the various surround parameters for optimum surround effect.

Note: The parameter settings are valid only when listening in Dolby Pro Logic II Music mode.

When selecting the "PANO (Panorama)" mode

This mode extends the front stereo image to include the surround

speakers for an exciting "wraparound" effect with side wall imaging.

Select "OFF" or "ON"(default value:OFF).

When selecting the "C. WIDTH (Center width)" control

This adjusts the center image so it may be heard only from the

center speaker, only from the left/right speakers as a phantom

image, or from all three front speakers to varying degrees. The

control can be set in 8 steps from 0 to 7 (default value : 3).

When selecting the "DIMEN (Dimension)" control

This gradually adjusts the soundfield either towards the front or

towards the rear. The control can be set in 7 steps from -3 to +3

(default value : 0).

1. Press the CURSOR UP()/DOWN() buttons to select the "PLII MSC", then press the ENTER button.

2. Press the CURSOR UP()/DOWN() buttons to select the desired parameter.

3. Press the CURSOR LEFT()/ RIGHT() buttons to adjust the selected parameter as desired.

4. Repeat the above steps 2 and 3 to adjust other parameters.

RD-6513(A) 2008.8.21 12:20 PM 페이지 42

ENGLISH

Troubleshooting Guide

PROBLEM POSSIBLE CAUSE REMEDY

No power

No sound

No sound from the surround

speakers

No sound from the center

speaker

Stations cannot be received

Preset stations cannot be

received

Poor FM reception

Continuous hissing noise

during FM reception,

especially when a stereo

broadcast is received.

Continuous or intermittent

hissing noise during AM

reception, especially at night.

Remote control unit does not

operate.

• The AC input cord is disconnected.

• Poor connection at AC wall outlet or the

outlet is inactive.

• The speaker cords are disconnected.

• The master volume is adjusted too low.

• The MUTE button on the remote control is

pressed to ON.

• Speakers are not switched on.

• Incorrect selection of the input source.

• Incorrect connections between the

components.

• Surround mode is switched off(stereo

mode).

• Master volume and surround level are too

low.

• A monaural source is used.

• Surround speaker setting is “N”.

• Surround mode is switched off(stereo

mode).

• Center speaker setting is “N”.

• Master volume and center level are too low.

• No antenna is connected.

• The desired station frequency is not tuned

in.

• The antenna is in wrong position.

• An incorrect station frequency has been

memorized.

• The memorized stations are cleared.

• No antenna is connected.

• The antenna is not positioned for the best

reception.

• Weak signals.

• Noise is caused by motors, fluorescent

lamps or lightning, etc.

• Batteries are not loaded or exhausted.

• The remote sensor is obstructed.

• Connect the cord securely.

• Check the outlet using a lamp or another

appliance.

• Check the speaker connections.

• Adjust the master volume.

• Press the MUTE button to cancel the

muting effect.

• Press the SPEAKER button to ON.

• Select the desired input source correctly.

• Make connections correctly.

• Select a surround mode.

• Adjust master volume and surround level.

• Select a stereo or surround source.

• Select the desired surround speaker

setting.

• Select the desired surround.

• Select the desired center speaker setting.

• Adjust master volume and center level.

• Connect an antenna.

• Tune in the desired station frequency.

• Move the antenna and retry tuning.

• Memorize the correct station frequency.

• Memorize the stations again.

• Connect an antenna.

• Change the position of the antenna.

• Install an outdoor FM antenna.

• Keep the receiver away from noise

sources.

• Install an outdoor AM antenna.

• Replace the batteries.

• Remove the obstacle.

If a fault occurs, run through the table below before taking your receiver for repair.

If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation,

consult your dealer. Under no circumstances should you attempt to repair the receiver yourself. This could void the

warranty.

RD-6513(A) 2008.8.21 12:20 PM 페이지 43

ENGLISH

Specifications

AMPLIFIER SECTION

• Power output, stereo mode, 6 Ω, THD 0.7%, 40 Hz~20 kHz ..................................................................................... 2100 W

• Total harmonic distortion, 6 Ω, 100 W, 1 kHz ................................................................................................................. 0.09 %

• Intermodulation distortion

60 Hz : 7 kHz= 4 : 1 SMPTE, 6 Ω, 100 W .................................................................................................................. 0.1 %

• Input sensitivity, 47 kΩ

Line (CD, TAPE, VIDEO) ........................................................................................................................................ 280 mV

• Signal to noise ratio, IHF “A” weighted

Line (CD, TAPE, VIDEO) .......................................................................................................................................... 92 dB

• Frequency response

Line (CD, TAPE, VIDEO), 20 Hz~50 kHz ...................................................................................................... +0 dB, -3 dB

• Output level

TAPE REC, 2.2 kΩ.................................................................................................................................................. 280 mV

PRE OUT (Subwoofer), 1 kΩ........................................................................................................................................ 1.0 V

• Bass/Treble control, 100 Hz/10 kHz ............................................................................................................................... ±10 dB

• Surround mode, only channel driven

Front power output, 6 Ω, 1 kHz, THD 0.7 % ................................................................................................ 110 W / 110 W

Center power output, 6 Ω, 1 kHz, THD 0.7 % .......................................................................................................... 110 W

Surround power output, 6 Ω, 1 kHz, THD 0.7 % .......................................................................................... 110 W / 110 W

DIGITAL AUDIO SECTION

• Sampling frequency .................................................................................................................................. 32, 44.1, 48, 96 kHz

• Digital input level

Coaxial, 75 Ω.......................................................................................................................................................... 0.5 Vp-p

Optical, 660 nm .......................................................................................................................................... -15 ~ -21 dBm

VIDEO SECTION

• Video format .................................................................................................................................................................... NTSC

• Input sensitivity (=Output level) , 75 Ω

Video (Composite (normal)) ........................................................................................................................................ 1 Vp-p

S-Video (luminance signal) ......................................................................................................................................... 1 Vp-p

(chrominance signal) .............................................................................................................................. 0.286 Vp-p

Component video (R-Y signal) ................................................................................................................................. 0.5 Vp-p

(B-Y signal) ................................................................................................................................ 0.5 Vp-p

(Y signal) .................................................................................................................................... 1.0 Vp-p

• HDMI connector ............................................................................................................................................................ 19 pin

FM TUNER SECTION

• Tuning frequency range .................................................................................................................................. 87.5 ~ 108 MHz

• Usable sensitivity, THD 3%, S/N 30 dB ...................................................................................................................... 12.8 dBf

• 50 dB quieting sensitivity, mono/stereo ........................................................................................................... 20.2 / 45.3 dBf

• Signal to noise ratio, 65 dBf, mono/stereo ............................................................................................................... 55 / 50 dB

• Total harmonic distortion, 65 dBf,1 kHz, mono/stereo .............................................................................................. 0.5 / 1.0 %

• Frequency response, 30 Hz~12 kHz ............................................................................................................................ ±3.0 dB

• Stereo separation, 1 kHz ................................................................................................................................................ 30 dB

• Capture ratio ...................................................................................................................................................................... 4 dB

• IF rejection ratio ............................................................................................................................................................... 80 dB

AM TUNER SECTION

• Tuning frequency range ................................................................................................................................... 520 ~ 1710 kHz

• Usable sensitivity ....................................................................................................................................................... 500 µV/m

• Signal to noise ratio ......................................................................................................................................................... 40 dB

• Selectivity .......................................................................................................................................................................... 25 dB

GENERAL

• Power supply ...................................................................................................................................................... 120 V ~ 60 Hz

• Power consumption ......................................................................................................................................................... 3.8 A

• Dimensions (W×H×D, including protruding parts) .............................. 440141370 mm (17-3/85-1/214-1/2 inches)

• Weight (Net) .................................................................................................................................................... 9.2 kg (20.3 lbs)

Note: Design and specifications are subject to change without notice for improvements.

RD-6513(A) 2008.8.21 12:20 PM 페이지 44

AUDIO/VIDEO RECEIVER

RD-6513

5707-00000-118-0S

cover 2008.8.21 12:21 PM 페이지 1

Sherwood Rd 6513 Users Manual 6513(A)

RD-6513 to the manual 75ab421f-1826-415b-9dee-287aaaa5bfc1

Navigation menu

Versions of this User Manual:

Views

Navigation