Shin Chuan Computer SC700PDT-BWG Portable Data Terminal User Manual rev2

Shin Chuan Computer Co., Ltd. Portable Data Terminal rev2

Contents

Manual 1

SC700 / SC720 User’s Manual WinCE. NET Rugged Portable Data Terminal Sep/20/2007 Ver: 0.5
Table of Contents Chapter 1. Introduction........................................................................ 1-1 1.1 About this Manual............................................................................1-1 1.2 User and Product Safety...................................................................1-2 1.3 Battery Safety...................................................................................1-3 1.4 FCC Statement.................................................................................1-4 1.5 Recycling & disposal instructions. ..................................................1-5 1.6 Regulatory information....................................................................1-5 1.7 Product Labeling..............................................................................1-6 1.8 System Specifications ....................................................................1-10 1.9 Environment Standard....................................................................1-12 1.10 Warranty and after service ...........................................................1-12 Chapter 2. Getting Started.................................................................... 2-1 2.1 Check the package ...........................................................................2-1 2.2 General View of the PDT.................................................................2-3 2.2.1 SC700 general view ................................................................2-3 2.2.2 SC720 general view ................................................................2-5 2.3 Charging the Battery Pack ...............................................................2-7 2.3.1 Installing the battery pack.......................................................2-7 2.3.2 Charging the battery pack with Power Adapter ......................2-9 2.3.3 Charging the battery pack with Single Dock ........................2-10 2.4. Handling the PDT .........................................................................2-12 2.4.1 Starting the PDT....................................................................2-12 2.4.2 Power on / off........................................................................2-12 2.4.3 Calibration of the touch Screen.............................................2-13 2.4.4 Adjusting the brightness........................................................2-13 2.4.5 To mute the Sound ................................................................2-14 2.4.6 Using the Stylus ....................................................................2-14 2.4.7 Using the SC700 Keypad......................................................2-14 2.4.8 Using the SC720 Keypad......................................................2-23 2.4.9 Using the Ear/Microphone....................................................2-33 2.5 Navigating the Display ..................................................................2-34 2.5.1 Setting Time and Date...........................................................2-34 2.5.2 Entering the Data ..................................................................2-34 2.5.3 The Command Bar................................................................2-35 2.5.4 The Task Bar .........................................................................2-35
2.5.5 The Soft Keypad ...................................................................2-36 2.5.6 Setting Up Wireless LAN RF ...............................................2-36 2.5.7 Reading barcodes, 1D laser version......................................2-37 2.5.8 Reading barcodes, 2D CMOS version..................................2-38 2.5.8 Help.......................................................................................2-40 2.6 Power management........................................................................2-41 2.6.1 Suspend Mode.......................................................................2-41 2.6.2 Resuming ..............................................................................2-42 2.7 Resetting the PDT..........................................................................2-42 2.7.1 Software (Warm) Reset.........................................................2-42 2.7.2 Cold Reset.............................................................................2-42 Chapter 3. Setting................................................................................. 3-1 3.1 Introduction......................................................................................3-1 3.2 Control Panel ...................................................................................3-1 3.2.1 BarCode Setting......................................................................3-2 3.2.2 Symbologies List ....................................................................3-8 3.2.3 Bluetooth Device Properties .................................................3-24 3.2.4 Certificates ............................................................................3-28 3.2.5 Control Center.......................................................................3-30 3.2.6 Date/Time..............................................................................3-34 3.2.7 Dialing Properties .................................................................3-35 3.2.8 Display Properties.................................................................3-37 3.2.9 Input Panel ............................................................................3-38 3.2.10 Internet Options ..................................................................3-39 3.2.11 Keyboard.............................................................................3-41 3.2.12 Network and Dial-up Connections......................................3-42 3.2.13 Owner..................................................................................3-46 3.2.14 Password .............................................................................3-47 3.2.15 PC Connection ....................................................................3-48 3.2.16 Power ..................................................................................3-49 3.2.17 Regional Settings ................................................................3-51 3.2.18 Remove Programs...............................................................3-52 3.2.19 Storage Manager .................................................................3-53 3.2.20 Stylus...................................................................................3-54 3.2.21 System.................................................................................3-55 3.2.22 Volume & Sounds Properties ..............................................3-57 3.3 Taskbar and Start Menu .................................................................3-58 Chapter 4. Communication.................................................................. 4-1
4.1 Installing & Setting Up Microsoft ActiveSync................................4-1 4.1.1 Installing Microsoft ActiveSync on the Host PC....................4-1 4.1.2 Connecting PDT to Host PC ...................................................4-1 4.2 Using ActiveSync.............................................................................4-1 4.2.1 Setting up a Partnership ..........................................................4-1 4.2.2 ActiveSync File Synchronization............................................4-3 4.3 Networking ......................................................................................4-3 Chapter 5. Software Applications ........................................................ 5-1 5.1 Introduction......................................................................................5-1 5.2 Software Applications......................................................................5-1 5.2.1 Inbox .......................................................................................5-1 5.2.2 Internet Explorer ...................................................................5-10 5.2.3 Media Player .........................................................................5-13 5.2.4 Messenger .............................................................................5-13 5.2.5 Microsoft WordPad...............................................................5-13 5.2.6 Remote Connection...............................................................5-19 5.2.7 Windows Explorer ................................................................5-20 5.3 DiskOnChip ...................................................................................5-22 5.3.1 Saving to Flash......................................................................5-22 5.3.2 DiskOnChip Location ...........................................................5-22 5.3.3 DiskOnChip Size ..................................................................5-23 Appendix A 2D Barcode Setting......................................................... A-1 A.1 Setup Tab........................................................................................A-1 A.1.1 Symbology Setup ..................................................................A-2 A.1.2 Decoder Setup.......................................................................A-3 A.1.3 Options..................................................................................A-4 A.2. Update Tab ....................................................................................A-5 A.3. Symbologies List...........................................................................A-6 A.3.1 Aztec......................................................................................A-6 A.3.2 Codabar .................................................................................A-7 A.3.3 Code 11 .................................................................................A-8 A.3.4 Code 128 ...............................................................................A-9 A.3.5 Code 39 ...............................................................................A-10 A.3.6 Code 49 ...............................................................................A-12 A.3.7 Code 93 ...............................................................................A-13 A.3.8 Composite Codes ................................................................A-14 A.3.9 Data Matrix .........................................................................A-15 A.3.10 EAN-8 ...............................................................................A-16
A.3.11 EAN-13 .............................................................................A-17 A.3.12 Interleaved 2 of 5 ..............................................................A-18 A.3.13 MaxiCode..........................................................................A-19 A.3.14 MicroPDF417....................................................................A-20 A.3.15 OCR-A, OCR-B, US Currency.........................................A-21 A.3.16 PDF417 .............................................................................A-31 A.3.17 Postnet...............................................................................A-32 A.3.18 QR Code............................................................................A-33 A.3.19 Reduced Space Symbology...............................................A-34 A.3.20 UPC-A...............................................................................A-35 A.3.21 UPC-E ...............................................................................A-36 A.3.22 UPC-E1 .............................................................................A-37 A.3.23 ISBT..................................................................................A-38 A.3.24 British Post........................................................................A-38 A.3.25 Canadian Post....................................................................A-39 A.3.26 Australian Post ..................................................................A-40 A.3.27 IATA 2 of 5........................................................................A-41 A.3.28 Codablock F ......................................................................A-42 A.3.29 Japanese Post.....................................................................A-43 A.3.30 Planet Code .......................................................................A-44 A.3.31 KIX (Netherlands) Post.....................................................A-45 A.3.32 MSI....................................................................................A-46 A.3.33 TCIF Linked Code 39 .......................................................A-47 A.3.34 Mayrix 2 of 5.....................................................................A-48 A.3.35 Korean Post.......................................................................A-49 Appendix B EasyPhone (GSM/GPRS)................................................B-1 B.1 Using the Phone Features...............................................................B-1 B.1.1 SIM Card...............................................................................B-1 B.1.2 Inserting a SIM Card.............................................................B-1 B.1.3 Start Before: ..........................................................................B-3 B.2 Accessing the dialer........................................................................B-4 B.2.1 Making a voice call ...............................................................B-5 B.2.2 Receiving a call .....................................................................B-5 B.3 Selecting settings............................................................................B-6 B.4 Internet connection.........................................................................B-7 B.4.1 Connecting ............................................................................B-8 Appendix C Expansion Module Applicability.....................................C-1 C.1 RFID Applicability.........................................................................C-1
C.2 GPS Applicability...........................................................................C-3
1-1 Chapter 1. Introduction Congratulations on purchasing the SC700/SC720 Portable Data Terminal (PDT), a Microsoft Windows®CE .Net rugged PDT. Its special combination of features makes it perfect for using in a wide range of applications. These features as: Intel® XScaleTM PXA270 520MHz 32 bits RISC Processor Windows® CE .NET 5.0 Operating System 128/256 MB SDRAM & 128/256 MB Flash ROM Open Architecture: User Accessible SD/CF/PCMCIA Slot 240 x 320, 3.5” Color TFT Display with Touch Panel One Numeric-Alpha Keyboards with LED backlight 802.11b/g Radio Support (Bluetooth Optional) Optionally Built-in GSM/GPRS Module Integrated 1D or 2D Barcode Scanner Changeable Scan Housing and Keypad Digital Camera 2.0M Pixel DSC Function (optional) GPS or RFID Function (Expansion module) 1.1 About this Manual The following chapters contained in this manual are: Chapter 1: Introduction General information about the PDT. Chapter 2: Getting started Describe the basic use of the PDT. Chapter 3: Setting Provide basic instructions for customizing the PDT. Chapter 4: Communication Describe how to use all kinds of communication of the PDT. Chapter 5: Software Application Describe the installed applications on the PDT. Appendix A. 2D Barcode Setting Provide instructions for customizing the 2D Engine. Appendix B Phone Tools (GSM/GPRS) Provide instructions for the Phone Tools Utility Appendix C Expansion Module Applicability RFID& GPS Function Explaining
1-2 1.2 User and Product Safety  Do not stare into the laser or LED beam directly or shine it into eyes.  Never use strong pressure onto the screen or subject it to severe impact, as the LCD panel could become cracked and possibility cause personal injury. If the LCD panel is broken, never touch the liquid inside because the liquid irritates the skin.  Although the PDT has passed the test of IP54 standard for water and dust resistance, avoid prolonged exposure to rain or other concentrated moisture. Such condition exceeds the IP54 standard, and could result in water or other contaminants entering into the PDT.  Use only the original approved AC Adapter with the PDT. Use of an unapproved AC Adapter could result in electrical problems, or even cause a fire or electrical shock to the user.  Do not disassemble the PDT. Servicing should be done by supplier only. If the PDT or accessories gets damaged due to wrong handling or unauthorized repair, warranty is void. In case the warranty seals are broken, warranty is void too.  Make regularly back-ups of all important data.  Under no circumstance will supplier be liable for any direct, indirect, consequential or incidental damages baring out of the use or inability to use the hardware and software and/or any data loss, even if supplier has been informed about the possibility of such damages.
1-3 1.3 Battery Safety Lithium-ion battery packs might get hot, explode, ignite and/or cause serious injury if exploded by abusive using. Please follow the safety warnings listed as below:  Do not throw the battery pack in fire. Do not expose the battery to high temperatures.  Do not connect the positive battery pack with negative battery pack to each other with any metal object (like wire).  Do not carry or store battery pack together with metal objects.  Do not pierce the battery pack with nails or drills, strike the battery pack with a hammer, step on the battery pack or otherwise expose it to strong impacts, shocks or excessive force.  Do not solder onto the battery pack.  Do not expose battery pack to liquid or allow the battery contacts to get wet.  Do not disassemble or modify the battery pack. The battery pack contains safety and protection measures, which, if damaged, may cause the battery pack to generate heat, explode or ignite.  Do not discharge the battery pack using any device except for the specified device. When it is used in devices other than the specified devices, the battery pack can be damaged or its life expectancy reduced. If the device causes any abnormal current to flow, it may cause the battery pack to become hot, explode or ignite and cause serious injury.  In the event the battery pack leaks and the fluid gets into one’s eye, do not rub the eye. Rinse well with water and immediately seek medical care. If left untreated, the battery fluid could cause damage to the eye.
1-4 1.4 FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. Body-worn Operation For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with the Shin Chuan Computer Co., Ltd. accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other
1-5 antenna or transmitter except built-in tested devices. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. Caution: SCC declares that SC700 ( FCC ID: TQ2-SC700PDT-BWG ) / SC720 ( FCC ID: TQ2-SC720PDT-BWG ) is limited in CH1~CH11 for 2.4GHz by specified firmware controlled in U.S.A. The FCC ID of SC700/SC720 is TQ2-SC700PDT-BWG LED AND LASER SAFETY INFORMATION  Class II LED/Laser Product  Do not stare at the LED/Laser or shine into eyes  Do not allow young children to use the product without adult supervision  Do not replace/repair the LED/Laser, these are not user replaceable  Do not shine the LED/Laser on a shiny reflective surface 1.5 Recycling & disposal instructions. Do not throw this product in the home waste bin. For proper end-of-life treatment consult the Environmental care section of www.sccltd.com.tw 1.6 Regulatory information. For CE, FCC, RoHS and other Document of Conformities, consult the Regulatory section of www.sccltd.com.tw
1-6 1.7 Product Labeling The PDT has several labels as showed in Figure 1-1 to 1-4. A. SC700 Figure 1-1 Product Labeling (Front side view) Label nr. Description 1 LCD panel protection film 2 SC700 logo 5 Warranty seal PDT 10 SIM label (only use on GSM/GPRS) Table 1-1 Front labeling
1-7 Figure 1-2 Product Labeling (Back side view) Label nr. Description 3 System and regulatory label 4 LED/Laser radiation warning label 5 Warranty label bar code reader 6 Serial number 7 Configuration number 8 Windows CE .NET label 9 NCC label (only use on Traditional Chinese version) 11 PenPower label (only use on Simplified Chinese version) 12 CCC label (only use with China) Table 1-2 Rear labeling
1-8 B. SC720 Figure 1-3 Product Labeling (Front side view) Label nr. Description 1 LCD panel protection film 2 SC720 logo 5 Warranty seal PDT 9 SIM label (only use on GSM/GPRS) Table 1-3 Front labeling
1-9 Figure 1-4 Product Labeling (Back side view) Label nr. Description 3 System and regulatory label 4 LED/Laser radiation warning label 5 Warranty label bar code reader 6 Serial number 7 Configuration number 8 Windows CE .NET label 10 PenPower label (only use with China) Table 1-4 Rear labeling
1-10 1.8 System Specifications The SC700 / SC720 detailed specifications as follows. Unless otherwise noted, all the specifications are subject to change without prior notification. Table 1-5 System Specification SC700 / SC720 Processor - 520MHz Intel PXA270 32 bits RISC CPU Memory - 128/256MB Flash ROM - 128/256MB SDRAM Display - 240 x 320 3.5” TFT 256K Color LCD with LED backlight Audio - One mono speaker - 2.5mm DIA Stereo Earphone Jack with Microphone input Radio Support - Wireless LAN: 802.11b/g - Bluetooth: Class II (optional) - GSM/GPRS: (optional) Communication Ports - USB: Support USB v1.1 both host and client. (PDT and Cradle) - Serial: RS232 via optional cable or Cradle. Scan Engine - Symbol, Opticon Laser (1D) Engine. (optional) - HHP 1D/2D Image. (optional) - Opticon Long range engine. (optional) - Opticon 2D Image. (optional) Expansion Slot - One SD Card Slot (SD memory only, no SDIO support) - One Compact Flash type-II Slot (Availability depends of PDT model) LED - One Triple-Color LED for Charger Indicator and Alarm Notification - One Dual-Color LED for Scanner Indicator
1-11 SC700 / SC720 Power System - Standard Li-Ion Battery Pack, 3.7V, 3000mAh - Advanced Smart Battery with Gas-Gauge - Built-in Battery Charger - 2.4V/15mAh rechargeable backup battery - One Battery Cover Sensor Switch - Power Adapter: 100~240V AC, 50/60Hz Input ; 5VDC/2.6A Output SC700 - One Power Button - Three Barcode Scanner Buttons - Four Navigation Buttons - Four Application Buttons - Sixteen Alpha-Numeric Keypad - One Pistol Trigger Button - One Application Hot Key Keypad / Buttons SC720 - One Power Button - Four Barcode Scanner Buttons - Four Navigation Buttons - Four Application Buttons - Forty-four Alpha-Numeric Keypad - One Pistol Trigger Button - One Application Hot Key SC700 - Dimensions: L : 192.5mm W: 91.3mm / 78mm H: 60.6mm / 42.2mm - Weight: 560g with Standard Battery Pack 500g without Battery Pack Dimensions and Weight SC720 - Dimensions: L : 220mm W: 91.3mm / 78mm H: 60.6mm / 42.2mm - Weight: 660g with Standard Battery Pack 600g without Battery Pack Color - Black
1-12 SC700 / SC720 Peripherals and Accessories - Optional: RS232 Serial Cable for Terminal / USB Host Cable for Terminal / High-Capacity Li-Ion Battery Pack (3.7V, 4000 mAh) / RFID Card Cover / Single Dock / Pistol Grip/ 4 Slot Battery Charger / Car Adapter / Holster / LCD Protective Film / Finger Printer & RS232 Cable / RFID Module / GPS Module Software - Microsoft Windows CE.NET 5.0 Professional 1.9 Environment Standard Table 1-6 Environment Standards Operating Temperature 14oF ~ 122oF( -10oC ~ 50oC) Storage Temperature -4oF ~ 158oF (-20oC ~ 70oC) Humidity 5% ~ 95% (non-condensing) Drop 5ft (1.5m) Drop onto Concrete Water & Dust proof IP54 Certificated & IP64 Compliant Vibration MIL STD 810F 1.10 Warranty and after service Should this PDT be malfunctioned, please contact your original retailer providing information about the product name, the serial number, and the details about the problem.
2-1 Chapter 2. Getting Started 2.1 Check the package Open the package and check all the parts are inside without shortage and damage: A. SC700 Figure 2-1 Inside the package 1. SC700 Terminal 2. Standard Battery Pack (3.7V, 3000 mAh) 3. USB Client Cable for Terminal 4. Stylus 5. AC Power Cord 6. Earphone/ Microphone Set 7. Standard AC Adapter 5VDC/2.6A 8. CF Support Guide (availability depends of PDT model) 9. Quick Guide (not shown in the picture)
2-2 B. SC720 Figure 2-2 Inside the package 1. SC720 Terminal 2. Standard Battery Pack (3.7V, 3000 mAh) 3. USB Client Cable for Terminal 4. Stylus 5. AC Power Cord 6. Earphone/ Microphone Set 7. Standard AC Adapter 5VDC/2.6A 8. CF Support Guide (availability depends of PDT model) 9. Quick Guide (not shown in the picture)
2-3 2.2 General View of the PDT 2.2.1 SC700 general view Figure 2-3 SC700 front side view Figure 2-4 SC700 back side view
2-4 Table 2-1 Description of SC700 General View “Red” color Reading barcode 1 Scanner LED Indicator “Green” color Successful reading “Red” color Charging battery 2 Charge LED Indicator “Green” color Battery charged full 3 LCM / Touch Panel Do specific action through touch panel by stylus 4 Left Scan key Right Scan key Scan key Start scanning the barcode by pressing any one of these three scan keys 5 Power key Puts the terminal into and wakes the terminal from suspend mode. 6 F1 ~ F4 key The four application keys, hot keys of application program defined by end user. 7 Navigation key Navigation keys for left, right, up and down directions 8 Alpha-Numeric keys Numeric keys, Change to Alpha keys after pressing Alpha key. 9 Alpha key Toggle Alpha-mode for Alpha-Numeric keys 10 Fn key This key is used in combination with other keys to type special characters and perform system functions. 11 Enter key This key confirms data entry 12 Earphone Jack Connector A connector to plug a earphone 13 USB / Serial / Synchronization port A connector to support USB Host/Client and serial functions 14 Scan window A window for scanning of barcode reader 15 Stylus Use the stylus for selecting items and entering information. 16 Battery Cover Protect Battery pack, keep the switch of battery cover to leave system from suspend mode 17 Battery cover Latch To keep Battery Cover locked 18 Hand Strap This strap can be sealed tighter or looser 19 Speaker 1W speaker for audio sound 20 DC Power Jack A connector to support AC power. 21 End Cap Protect CF slot and SD slot from dust and water
2-5 2.2.2 SC720 general view Figure 2-5 SC7200 front side view Figure 2-6 SC720 back side view
2-6 Table 2-2 Description of SC720 General View “Red” color Reading barcode 1 Scanner LED Indicator “Green” color Successful reading “Red” color Charging battery 2 Charge LED Indicator “Green” color Battery charged full 3 LCM / Touch Panel Do specific action through touch panel by stylus 4 Left Scan key Right Scan key Scan key Start scanning the barcode by pressing any one of these three scan keys 5 Power key Puts the terminal into and wakes the terminal from suspend mode. 6 F1 ~ F4 key The four application keys, hot keys of application program defined by end user. 7 Navigation key Navigation keys for left, right, up and down directions 8 Alpha keys Alpha key. 9 Numeric keys Numeric keys. 10 Fn key This key is used in combination with other keys to type special characters and perform system functions. 11 Enter key This key confirms data entry 12 Earphone Jack Connector A connector to plug a earphone 13 USB / Serial / Synchronization port A connector to support USB Host/Client and serial functions 14 Scan window A window for scanning of barcode reader 15 Stylus Use the stylus for selecting items and entering information. 16 Battery Cover Protect Battery pack, keep the switch of battery cover to leave system from suspend mode 17 Battery cover Latch To keep Battery Cover locked 18 Hand Strap This strap can be sealed tighter or looser 19 Speaker 1W speaker for audio sound 20 DC Power Jack A connector to support AC power. 21 End Cap Protect CF slot and SD slot from dust and water
2-7 2.3 Charging the Battery Pack Before using the PDT, perform the basic procedure of charging the battery pack through the following steps. 2.3.1 Installing the battery pack 1. On the PDT attached with a hand-strap, detach and loose the hand-strap. Figure 2-7 Release the Hand strap from PDT 2. Turn the locking screws (right and left) downwards and lift the battery cover away from the PDT. Figure 2-8 Detach the battery cover from PDT
2-8 3. Insert the battery pack into the battery compartment with the label facing out, and ensuring the battery snaps into place. Figure 2-9 Insert the battery pack 4. Replace the battery cover by inserting the top first, and then press the bottom in firmly. Turn the locking screws (right and left) upwards to secure the cover to the PDT. Figure 2-10 Replace the battery cover
2-9 5. Charge time. For the first time to charge the battery pack needs approximately 6 hours. Subsequent charging time needs approximately 4 hours. ◆. When charging the battery pack, the charge LED indicator on the PDT turns on Red. After the battery pack is fully charged, the charge LED indicator turns to Green. 2.3.2 Charging the battery pack with Power Adapter 1. Connect the Power cord to the Power adapter. 2. Plug in the connector of the power adapter. 3. Connect the power cord to a power source. Figure 2-11 Charging with power adapter ◆ When charging the battery pack, the charge LED indicator on the PDT turns on Red. ◆ After the battery pack is fully charged, the charge LED indicator turns to Green.
2-10 2.3.3 Charging the battery pack with Single Dock a) Leave the battery pack inside of the PDT 1. Connect the Power cord to the Power adapter 2. Connect the power cord to a power source 3. Plug in the connector of the power adapter with Single Dock 4. Insert the PDT into the Single Dock Figure 2-12 Charging with Single Dock ◆ When charging the battery pack, the charge LED indicator on the PDT turns on Red. After the battery pack is fully charged, the charge LED indicator turns to Green. CAUTION: Single Cradle Adapter is 5Vdc/6.5A, which is different from PDT Adapter (5Vdc/2.6A). Please use the Single Cradle Adapter only. b) Place the spare battery pack into the Single Cradle’s spare Battery charging slot 1. Connect the power cord to the power adapter 2. Connect the power cord to a power source 3. Plug in the connector of the power adapter with Single Cradle 4. Insert the Battery pack into the Single Cradle’s spare Battery slot.
2-11 ◆ When charging the Battery pack in the Single Cradle’s spare Battery slot, the Single Cradle charging LED will turn on Red. After the Battery pack is fully charged, this LED will turn to Green. CAUTION: Please do not remove the Battery pack too long from PDT after you have already full-charged the Battery pack and backup battery pack and start to use the PDT. Otherwise the data stored inside SDRAM memory will be lost. Please also keep in mind power the PDT off if you want to change the main Battery pack.
2-12 2.4. Handling the PDT 2.4.1 Starting the PDT Press the Power key to turn on/off the PDT. If the PDT does not power on, perform a cold boot. See 2-7 Resetting the PDT. CAUTION: When a battery is fully inserted in PDT for the first time, upon the PDT’s first power up, the device boots and powers on automatically. Figure 2-13 Starting the PDT 2.4.2 Power on / off  To turn on the PDT Press the Power key briefly ( ). If the PDT does not power on, perform the cold reset. See chapter 2.7.1. As the PDT initializes its file system, it splash screen displays for about 30 seconds followed by calibration screen. Every time you perform a cold reset, these screens will also appear. To turn off the PDT, just press the Power key again. This action does not actually turn off the PDT, it only turns the PDT into suspend mode. All running applications remain as you left them, until you press the Power key again to resume operation of the PDT When the PDT is powered on for the first time, it initializes its system. A splash screen (figure 2-13) appears for a short period of time followed by the Wince.NET 5.0 window. This section offers the basic procedures of PDT using.
2-13 2.4.3 Calibration of the touch Screen On the initial boot-up of the PDT, the stylus calibration screen (Labeled Align Screen) opens. Use the stylus to press and hold briefly on the center of each target as it moves around the screen. If necessary, adjust the backlight on the PDT to make the screen readable. (See below 2.4.4. Adjust the brightness). When you feel the touch screen function is poor or the operation does not match the exact location it should be, please recalibrate the screen by using the stylus to tap the Start > Settings > Control Panel > Stylus, to open the “Calibration” to recalibrate again. Figure 2-14 Calibration 2.4.4 Adjusting the brightness The factory default for the brightness is in Middle level. You can adjust the brightness to meet your environment and comfort as: 1) Become brighter: Press the key and then press on the right key of Navigation key . 2) Become darker: Press the key and then press on the left key of Navigation key . 3) The display will become dimmer automatically, if you do not perform any operation for a specific period of time. This will help to save the battery power. You can set up the specific period of time to see chapter 2.6 as reference.
2-14 2.4.5 To mute the Sound To mute the sound, press the key first, and then press the key to turn off and on of the sound. 2.4.6 Using the Stylus The stylus is located next to hand-strap on the left rear of the PDT. The stylus function is same as the mouse on a PC. Use the stylus to: 1) Navigate the display, select menu item and open optional applications. 2) Tap the characters on soft keyboard panel. 3) Hold the stylus on the screen and drag across the screen to select the list of multiple items. CAUTION: Never use a pen, pencil, or other sharp object on the display to avoid any unexpected damage of the touch screen. 2.4.7 Using the SC700 Keypad Figure 2-15 SC700 Keypad
2-15 Table 2-3 Keypad List Key Main Function Fn + Main Function Alpha + Main Function None. (Reserved for Customer) Main Barcode Scan Key Power On/Off Internet Explorer Microsoft WordPad Inbox File Explorer Right Backlight Increase Left Backlight Decrease Down Page Down Up Page Up ESC Audio Mute ＄＄＄＄ € Backspace TAB Caps Change to letters Function change 1 ＠＠＠＠ ：：：： ＼＼＼＼ 2 ’ ＡＡＡＡ ＢＢＢＢ ＣＣＣＣ 3 ＋＋＋＋ ＤＤＤＤ ＥＥＥＥ ＦＦＦＦ 4 Paste ＧＧＧＧ ＨＨＨＨ ＩＩＩＩ 5 Del ＪＪＪＪ ＫＫＫＫ ＬＬＬＬ 6 －－－－ (Minus Sign) ＭＭＭＭ ＮＮＮＮ ＯＯＯＯ 7 Copy ＰＰＰＰ ＱＱＱＱ ＲＲＲＲ ＳＳＳＳ 8 ＆＆＆＆ ＴＴＴＴ ＵＵＵＵ ＶＶＶＶ 9 ＊＊＊＊ ＷＷＷＷ ＸＸＸＸ ＹＹＹＹ ＺＺＺＺ
2-16 Key Main Function Fn + Main Function Alpha + Main Function 0 Space 〔〔〔〔 〕〕〕〕 . (Point) Start Menu ，，，， ；；；； Enter ／／／／ ＝＝＝＝ ％％％％ Table 2-4 Special Assembler Key Assembler Key Functionality Definition Warm Reset Press “F1” and “F4” button simultaneously. Cold Reset Press “Power”, “F1” and “F4” button simultaneously. Table 2-5 Definition of main Function Key Main Function Definition None. Keep its function or by customer demand. Main Barcode Scan Key The key activates the scan function of SC700. Power On/Off The key puts the terminal into and wakes the terminal from suspend mode if this key button is not pressed more than two seconds. Internet Explorer Application key 1, User can define F1 function from setting. Microsoft WordPad Application key 2, User can define F2 function from setting. Inbox Application key 3, User can define F3 function from setting. File Explorer Application key 4, User can define F4 function from setting. Right Move the cursor one character to the right. The cursor will move continuously if button is pressed continuously. Left Move the cursor one character to the left. The cursor will move continuously if button
2-17 Key Main Function Definition is pressed continuously. Down Move the cursor down one row or line The cursor will move continuously if button is pressed continuously. Up Move the cursor up one row or line The cursor will move continuously if button is pressed continuously. ESC This key performs a cancel action Backspace “Backspace” key, it moves the cursor back one space each time the key is pressed. It deletes the previous character each time it is pressed if you are typing text. The cursor will move continuously if button is pressed continuously. Change to letters 1. The key enables you to toggle between the numeric and alpha modes. Numeric mode is when you type numbers with number keys. Alpha mode is when you type letters with the number keys. 2. When you press key, it appears “Alpha” icon at the Task bar to indicate Alpha mode is enabled. The keypad stays in the alpha mode until you press key again. Function change The key is used in combination with other keys to type special characters and perform system functions. 1 Number key “1” 2 Number key “2” 3 Number key “3” 4 Number key “4” 5 Number key “5”
2-18 Key Main Function Definition 6 Number key “6” 7 Number key “7” 8 Number key “8” 9 Number key “9” 0 Number key “0” . Point key Enter This key confirms data entry 2.4.7.1 Special Function by “Fn” + main Function The “Fn” key is used in combination with other keys to type special characters and perform system functions. Table 2-6 Special Function key define Key Sequence Fn + Main Function Definition Increase of Brightness Increase the LED backlight brightness of display screen(Lighter) You must press key, then press key to increase backlight brightness each time. Decrease of Brightness 1. Decrease the LED backlight brightness of display screen (darker) 2. You must press key, then press key to decrease backlight brightness each time. Page Down 1. Move the cursor down one page. The cursor will move continuously if button is pressed continuously. 2. You must press key, then press key to cursor down one page
2-19 Key Sequence Fn + Main Function Definition each time. Page Up 1. Move the cursor up one page. The cursor will move continuously if button is pressed continuously. 2. You must press key, then press key to cursor up one page each time. Audio Mute 1. Toggle the audio mute/on 2. You must press key, then press key to enable audio mute or turn on audio function each time. TAB 1. The “TAB” function is to move the cursor to the next tab stop or the next control (on a form) 2. To do this function by pressing key first, and then pressing key each time. @ Enter an @ by pressing key, then pressing key. ’ Enter a {’} by pressing key, then pressing key. ＋＋＋＋ Enter a plus sign by pressing key, then pressing key
2-20 Key Sequence Fn + Main Function Definition Paste 1. It is to do “Paste” function. 2. To do this function by pressing key first, and then pressing key each time. Del 1. The “Delete” function delete the next character forward each time. 2. To do “Delete” function by pressing key first, and then pressing key each time. －－－－ (Minus Sign) Enter a minus sign by pressing key, then pressing key. Copy 1. Copy action. 2. You must press key, then press key to do “Copy” action each time. ＆＆＆＆ Enter an AND sign by pressing key, then pressing key. ＊＊＊＊ Enter an asterisk sign by pressing key first, and then pressing key. Space 1. The “Space” function is to move the cursor one space. 2. To do this function by pressing
2-21 Key Sequence Fn + Main Function Definition key first, and then pressing key each time. Start Menu 1. It displays the Start menu. 2. To do this function by pressing key first, and then pressing key each time. ／／／／ Enter a slash by pressing key first, and then pressing key. 2.4.7.2 Alpha plane keys by “Alpha” + main Function 1. The key enables you to toggle between the numeric and alpha modes. Numeric mode is when you type numbers with number keys. Alpha mode is when you type letters with the number keys. 2. When you press key, it appears “Alpha” icon at the Task bar to indicate Alpha mode is enabled. It means Alpha mode is disabled if there isn’t “Alpha” icon at Task bar. The keypad stays in the alpha mode until you press key again. For an example to type “cap1” word, press < wait 0.5 seconds > . 3. If you want to type a lowercase “c”, press (The key three times, the key is needed if it’s the first alpha character keying in.). If a letter that is on the same key as the last letter entered, wait two seconds after you pressed the last key, then you can enter the correct series of keystrokes to create the next letter.
2-22 4. While you are in the Alpha mode and you press key to initial the Caps mode, you will render a Caps Lock until you press key again. Once you are in Caps mode, you stay in Caps until it is pressed again. 5. It appears “A” icon at Task Bar during Caps mode. Table 2-7 Alpha + Numeric keys define To enter Press the Keys To enter Press the Keys ＄ € Caps ：：：： ＼＼＼＼ ａ Ａ ｂ Ｂ ｃ Ｃ ｄ Ｄ ｅ Ｅ ｆ Ｆ ｇ Ｇ ｈ Ｈ ｉ Ｉ ｊ Ｊ ｋ Ｋ ｌ Ｌ ｍ Ｍ ｎ Ｎ ｏ Ｏ ｐ Ｐ ｑ Ｑ ｒ Ｒ ｓ Ｓ ｔ Ｔ ｕ Ｕ ｖ Ｖ ｗ Ｗ ｘ Ｘ
2-23 To enter Press the Keys To enter Press the Keys ｙ Ｙ ｚ Ｚ 〔 〕 ， ； ＝ ％ Note: 1. The key is not needed to key in if the character isn’t the first alpha character being keyed in. 2. The keys are not needed to key in if it is not the first capital alpha character being keyed in. 2.4.8 Using the SC720 Keypad Figure 2-16 SC720 Keypad
2-24 Table 2-8 Keypad List Key Main Function Fn + Main Function None Main Barcode Scan Key Power On/Off Internet Explorer Microsoft WordPad Inbox File Explorer Right Increase of Brightness Left Decrease of Brightness Down Page Down Up Page Up Esc Caps Tab Backspace A F5 B F6 C F7 D F8 E ( F ) G [ H ] I { J }
2-25 Key Main Function Fn + Main Function K € L $ M # N % O ^ P ~ Q , R 、、、、 S ! T ? U \ V = W X Y ; Z / 1 @ 2 ’ 3 ＋＋＋＋ 4 Copy 5 Del 6 －－－－ (Minus Sign) 7 Paste 8 & 9 ＊＊＊＊ 0 Start Menu . (Point) Space SHIFT Function change Enter
2-26 Table 2-9 Special Assembler Key Assembler Key Functionality Definition Warm Reset Press “F1” and “F4” button simultaneously. Cold Reset Press “Power”, “F1” and “F4” button simultaneously. Table 2-10 Definition of main Function Key Main Function Definition None Keep its function by customer demand. Main Barcode Scan Key The key activates the scan function of SC720. Power On/Off The key puts the terminal into and wakes the terminal from suspend mode if this key button is not pressed more than two seconds. Internet Explorer Application key 1, User can define F1 function from setting. Microsoft WordPad Application key 2, User can define F2 function from setting. Inbox Application key 3, User can define F3 function from setting. File Explorer Application key 4, User can define F4 function from setting. Right Move the cursor one character to the right. The cursor will move continuously if button is pressed continuously. Left Move the cursor one character to the left. The cursor will move continuously if button is pressed continuously. Down Move the cursor down one row or line The cursor will move continuously if button is pressed continuously.
2-27 Key Main Function Definition Up Move the cursor up one row or line The cursor will move continuously if button is pressed continuously. Esc This key performs a cancel action Caps Conversion of the capital & lower case of the alpha key. Tab The “TAB” function is to move the cursor to the next tab stop or the next control (on a form) Backspace “Backspace” key, it moves the cursor back one space each time the key is pressed. It deletes the previous character each time it is pressed if you are typing text. The cursor will move continuously if button is pressed continuously. ~ A ~ Z Use the alpha keys for alphabetic characters. ~ 1 ~ 0 Numeric value keys. . Point key SHIFT While under lower-case character environment, remain "Shift" key pressed then press alpha key(s) to have "upper-case character(s)", and vice versa. Function change The key is used in combination with other keys to type special characters and perform system functions. Enter This key confirms data entry 2.4.8.1 Special Function by “Fn” + main Function The “Fn” key is used in combination with other keys to type special characters and perform system functions. Table 2-11 Special Function key define
2-28 Key Sequence Fn + Main Function Definition Increase of Brightness Increase the LED backlight brightness of display screen(Lighter) You must press key, then press key to increase backlight brightness each time. Decrease of Brightness 3. Decrease the LED backlight brightness of display screen (darker) 4. You must press key, then press key to decrease backlight brightness each time. Page Down 3. Move the cursor down one page. The cursor will move continuously if button is pressed continuously. 4. You must press key, then press key to cursor down one page each time. Page Up 3. Move the cursor up one page. The cursor will move continuously if button is pressed continuously. 4. You must press key, then press key to cursor up one page each time. F5 (Barcode Settings) Application key 5, User can define F5 function from setting. F6 (Media Player) Application key 6, User can define F6 function from setting. F7 (Calculator) Application key 7, User can define F7 function from setting. F8 (Information) Application key 8, User can define F8
2-29 Key Sequence Fn + Main Function Definition function from setting. ( Enter a ( by pressing key, then pressing key. ) Enter a ) by pressing key, then pressing key. [ Enter a [ by pressing key, then pressing key. ] Enter a ] by pressing key, then pressing key. { Enter a { by pressing key, then pressing key. } Enter a } by pressing key, then pressing key. € Enter a € by pressing key, then pressing key. $ Enter a $ by pressing key, then pressing key. # Enter a # by pressing key, then
2-30 Key Sequence Fn + Main Function Definition pressing key. % Enter a % by pressing key, then press key. ^ Enter a ^ by pressing key, then press key. ~ Enter a ~ by pressing key, then pressing key. , Enter a , by pressing key, then pressing key. 、、、、 Enter a 、、、、 by pressing key, then pressing key. ! Enter a ! by pressing key, then pressing key. ? Enter a ? by pressing key, then pressing key. \ Enter a \ by pressing key, then pressing key. = Enter a = by pressing key, then
2-31 Key Sequence Fn + Main Function Definition press key. Increases device volume, press key and then press key. Decreases device volume, press key and then press key. ; Enter a ; by pressing key, then pressing key. / Enter a / by pressing key, then pressing key. @ Enter a @ by pressing key, then pressing key. ’ Enter a {’} by pressing key, then pressing key. ＋＋＋＋ Enter a plus sign by pressing key, then pressing key Copy 3. It is to do “Paste” function. 4. To do this function by pressing key first, and then pressing key each time. Del 3. The “Delete” function delete the next character forward each time. 4. To do “Delete” function by pressing
2-32 Key Sequence Fn + Main Function Definition key first, and then pressing key each time. －－－－ (Minus Sign) Enter a minus sign by pressing key, then pressing key. Paste 3. Copy action. 4. You must press key, then press key to do “Copy” action each time. ＆＆＆＆ Enter an AND sign by pressing key, then pressing key. ＊＊＊＊ Enter an asterisk sign by pressing key first, and then pressing key. Start Menu 3. It displays the Start menu. 4. To do this function by pressing key first, and then pressing key each time. Space 3. The “Space” function is to move the cursor one space. 4. To do this function by pressing key first, and then pressing key each time.
2-33 2.4.9 Using the Ear/Microphone Connect Ear/Microphone to PDT earphone jack connector. The PDT is not built in microphone; if you like to record the voice, you have to use Ear/Microphone. Figure 2-17 Ear/Microphone
2-34 2.5 Navigating the Display 2.5.1 Setting Time and Date In the Date/Time options, you can change the year, month, date, time, time zone, or select automatic adjust for Daylight Saving Time. To set or change the date and time: 1. Select Start > Settings > Control Panel > Date/Time 2. To change the year, select the year or open a numeric dial. Select the up arrow to increase the value; select the down arrow to decrease the value. Or you can type a new value in the field. 3. Select the month to open a pull-down list of months or press the arrow buttons to either side of the month to increase or decrease the month. Figure 2-18 Date/Time properties 4. To change the time, select the hour, minute, seconds, or AM/PM and select the up arrow to increase the value; select /tape the down arrow to decrease the value. Or you can type a new value in the field. 5. Select your correct time zone from the pull-down list. 6. To automatically adjust the clock for Daylight Saving Time, enable the checkbox at the bottom of the screen. 7. Select Apply to make save your changes [and make additional modifications] or select OK to exit the Date/Time settings. 2.5.2 Entering the Data To select and open programs, select Start > Programs from the task bar to open a list of available programs. Or if the program has a icon on the desktop, double-tap to open it. There are several ways to enter data on the PDT once in an application:  Use the keypad to enter alpha-numeric characters, Refer to “2.4.7 Using the
2-35 SC700 keypad”.  Use the stylus on the touch screen.  Select text in the same way you select the text on a PC. Use the stylus to highlight the desired text by dragging the stylus across the desired text, double-tapping to select one word and triple-rapping to select an entire line/paragraph. Refer to “2.5 Navigating the Display” starting.  Use the soft input panel (digital keyboard) with the stylus.  Use the bar code scanning to enter data. Press the trigger or “Barcode Scan” key to initiate a scan. The scanned data will enter the current application’s open file. Refer to “2.5.7 Reading barcodes, 1D laser version” starting for more information on using a scanner. For more information on factory installed applications, Refer to Chapter 4 “ Software Programs”. 2.5.3 The Command Bar Use the Command bar at top of the screen to perform tasks in programs, such a opening a file, or editing a file. 2.5.4 The Task Bar The Task bar at the bottom of the screen displays the icon, an icon for the active program, the current time, and system icons for utilities loaded in memory. The Task bar includes menu names, buttons, and the keyboard icon, which opens and closes the soft input panel (SIP). The Task bar allows you to select and close programs. Refer to Figure 2-19 to view the Task bar. Figure 2-19 Task Bar & Command Bar Command Bar Task Bar
2-36 2.5.5 The Soft Keypad In applications that accept keypad input, the soft input panel (SIP) can be used to enter data using the stylus. The SIP is digital, QWERTY-style keyboard. To open the SIP, tap the keyboard icon to open the menu and select Hide Input Panel to close the keyboard. Use the stylus to select letters, numbers, or symbols from the Soft Input Panel for the current application. 2.5.6 Setting Up Wireless LAN RF 1) Press “Start”---“Setting”---“Control Panel” --- “WLAN Manager”. 2) Launch the WLAN Manager to Enable WLAN device. 3) Into AP Browser tab, tap Scan button to renew the network. 4) Select a network, tap the Join button or double tap it for more options. 5) Press OK to save all your Wireless LAN settings. 6) Tap the “Exit” button to Disable WLAN device. Figure 2-20 WLAN Manager Figure 2-21 WLAN Manager Note: WLAN is not connecting to network. WLAN is no signal.
2-37 WLAN signal is Low. WLAN signal is In General. WLAN signal is Good. Figure 2-22 WLAN Manager Figure 2-23 WLAN Manager 2.5.7 Reading barcodes, 1D laser version. To use the scanning function, complete the following steps: 1. If you have not already done so, remove the protective plastic film before using devices equipped with a 1D laser bar code reader. 2. Select Start > Setting > Control Panel > Barcode Setting; complete all configurations following all description of 3.2.1 BarCode Setting. 3. Run the WordPad software program. 4. Press one of the three barcode reader trigger buttons. 5. Aim the scanning beam at the center of barcode.
2-38 6. Good scanning position. The reading range is from 40 to 300mm distance. 1) Decrease the scanning distance to the bar code when scanning small barcodes. 2) Increase the scanning distance from the bar code when scanning large barcodes 3) The scanning area is visible by a red laser beam. 7. Bad scanning position. 1) Make sure that the laser beam sweeps across whole bar code. 2) Scanning operations may fail if the laser beam is positioned as below. 8. upon reading a barcode, the red LED indicator turns on until the trigger is release or after five seconds. The green LED and the beep tone indicates a good read. Note: This product scans using laser light. Never look directly into the laser light or shine the laser light into the eyes. 2.5.8 Reading barcodes, 2D CMOS version. The 2D CMOS version can read both 1D and 2D bar codes. To use the scanning function, complete the following steps: 1. If you have not already done so, remove the protective plastic film before using devices equipped with a 2D CMOS bar code reader. 2. Select Start > Setting > Control Panel > 2DBarcode; complete all configurations
2-39 following all description of Appendix A. 2D Barcode Setting. 3. Run the WordPad software program. 4. Press one of the three bar code reader trigger buttons. 5. Aim the scanning beam at the center of bar code. To assists in aiming, there are 4 green aiming light spots. The bar code should be between the outside 2 green spots. The scanner is in focus in case the center 2 green spots joins into 1 spot. 5. Good scanning position. The reading range is from 45 to 260mm distance. 1) Decrease the scanning distance to the bar code when scanning small barcodes. 2) Increase the scanning distance from the bar code when scanning large barcodes 3) The bar code should be located within the green light spots 4) The scanning area is visible by a red illumination area. 6. Bad scanning position. 1) Make sure that the laser beam sweeps across whole barcode. 2) Scanning operations may fail if the illumination beam is positioned as below.
2-40 7. Upon reading a bar code, the red LED indicator turns on until the trigger is release or after five seconds. The green LED and the beep tone indicates a good read. 2.5.8 Help To tap “?” can get help information for each program.
2-41 2.6 Power management 2.6.1 Suspend Mode The PDT will go into a suspend mode when it is idle for a period of time. The idle duration can be customized using the Power control panel (refer to Figure “Schemes Tab”) Suspend mode works and looks just like you have turned the unit off. Press the key to suspend the PDT, Press the key again for the PDT to resume its Previous state. Use the Battery power control panel to set the duration to switch state to Suspend mode when system using battery power. This will save battery power when PDT is not in use. Figure 2-24 Schemes Tab Suspending: The following conditions will suspend:  Press <Power> key while the unit is on.  The duration timer of item “Switch state to Suspend” expires, which indicates that there has been no use for a specified of time.  The battery pack is completely discharged.  Tap Start > Suspend Tap here to let PDT enter into suspend mode
2-42 2.6.2 Resuming Use one of following methods to resume (wake up the PDT):  Press <Power> key to suspend or resume (wake up).  Put the PDT into a dock. When a battery pack completely discharges while the unit is in suspend mode, the PDT remains suspended until discharged battery condition is corrected. 2.7 Resetting the PDT 2.7.1 Software (Warm) Reset A warm reset is a transition from the on, idle, or suspend power state that close all applications, clears the working RAM, but preserves the file system. Reason to Warm Reset: If an application “hangs”, initiate a warm reset to terminate the application only. Process to Warm Reset: To a warm reset, press “F1” and “F4” button simultaneously. After Warm Reset:  The desktop appears with the application shortcuts on the screen.  The custom settings in the registry are persistent. 2.7.2 Cold Reset 1) You can use Cold Reset to initiate device if WINCE.NET OS lock up or Warm Reset still can’t work 2) To perform Cold Reset, press “Power”, “F1” and “F4” button simultaneously. 3) Device will initiate boot up after Cold Reset. CAUTION: Only use the Warm Reset. Try warm reset before you initiate Cold Reset. All applications will be Closed and working RAM and all files will be cleared if you initiate the Cold Reset. It’s better usually to back up your files to Flash ROM, Flash Card or PC.
3-1 Chapter 3. Setting 3.1 Introduction To view available options for PDT’s setting, tap Start > Settings. Then, there are three items inside Settings: “Control Panel”, “Network and Dial-up” and “Taskbar and Start”. 3.2 Control Panel To view the Control Panel and settings you can modify by tapping Start > Settings > Control Panel. Figure 3-1 Control Panel
3-2 3.2.1 BarCode Setting CAUTION：：：：Please do not enter into any Barcode Application Program before settings completing this Barcode. There are three Tabs for scanner configuration setting: “Basic” Tab, “Code Configure” Tab and “Code ID” Tab. In addition, there is “BarCode Setup” for the “Code Configure” Tab. 3.2.1.1 “Basic” Tab Figure 3-2 Basic Tab Table 3-1 Basic Explaining Field Name Function Explaining Select the numbers of beep tone after scan OK. None After scanning the barcode, do not give out beep sound. Beep After Scan OK One Time After scanning the barcode, give out beep one time.
3-3 Field Name Function Explaining Two Times After scanning the barcode, give out beep two times. Scan Timeout (sec) Select the scanning timeout duration (in seconds) from this pull-down list. <2 ~ 20 sec, Default: 5> None After showing barcode, do not action. CRLF After showing the barcode, jump to next row. Space After showing the barcode, jump one unit. Termination Code Tab After showing the barcode, jump a section. Disable Disable this functionality. Continuous Scan 1 ~5 sec Alternate second number of Continuous Scan. Select a method based upon the barcode scanning application you will use. Type Writing A unit continues a unit, fast showing barcode number. Copy & Paste Once show barcode number. Keybd Message Disable Not show the barcode number. Prefix Type the desired label prefix in this text box Suffix Type the desired label suffix in this text box Default Press “Default” button to reset all configuration setting of “Basic” Tab into default values. F/W ver. Decoder firmware version. Set All To Default Press “Set All To Default” button to reset all configuration setting of “Basic” Tab, “Code Configure” Tab, “Code ID” Tab and all barcode of “BarCode Setup” into default values.
3-4 3.2.1.2 “Code Configure” Tab: Select the barcode symbologies you plan to scan from the list. Tap to enable/disable the desired symbologies. Figure 3-3 Code Configure Tab Table 3-2 Code Configure Explaining Barcode Symbology Explaining Type A. Numeric-only Barcodes UPC-E Compressed version of UPC code for use on small products. UPC-A Universal product code seen on almost all retail products in the USA and Canada. EAN-13 / ISBN EAN-13: European Article Numbering international retail product code. ISBN: Special use of the EAN-13 symbol to used internationally to mark books. EAN-8 / JAN-8 Compressed version of EAN code for use on small products. UPC-EAN Add-ON 2/5 UPC-A, UPC-E, EAN-13, and EAN-8 may all include an additional barcode to the right of the main barcode. This second barcode, which is usually not as tall as the primary barcode, is used to encode additional information for newspapers,
3-5 books, and other periodicals. Industrial 2 of 5 / IATA Older code not in common use. Interleaved 2 of 5 Compact numeric code, widely used in industry, air cargo, other applications. Plessey / MSI Plessey: Older code commonly used for retail shelf marking. MSI: Variation of the Plessey code commonly used in USA. Code 11 Used primarily for labeling telecommunications equipment. Codabar / NW 7 Older code often used in library systems, sometimes in blood bank. Matrix 2 of 5 Used in miscellaneous industrial applications, and mechanical numbering systems. Type B. Alphanumeric Barcodes Code 39 / Code32 General-purpose code in very wide use world-wide. Code 93 Compact code similar to Code 39. Code128 / UCC EAN128 Very capable code, excellent density, high reliability; in very wide use world-wide. Widely used data formatting model for Code 128 Type C. Others Barcodes China Post Used by China Postal Service for automated mail sorting. Code 4 --- GTIN Global Trade Identification Number Korea Code 3 of 5 --- RSS Reduced Space Symbology
3-6 3.2.1.3 “Code ID” Tab: Figure 3-4 Code ID Tab Table 3-3 Code ID Explaining Code ID is added into prefix of the barcode and let user identify which kind of barcode being scanned. Enable Code ID Enable this functionality. Set 1 ~ Set 5 Select one default value by Set 1 ~ Set 5. (See the “Table 3-4 Code ID Set1-Set5 Table”) User Define Establish number by oneself. Barcode List Set 1 ~ Set 5: defaults setting. User Define: select barcode to define. Default Press “Default” button to reset all configuration setting of “Code ID” Tab into default values. Table 3-4 Code ID Set1-Set5 Table Set 1 Set 2 Set 3 Set 4 Set 5 UPC-E S E C E E UPC-A M A A A E EAN-13 / ISBN M A A F E EAN-8 / JAN-8 P B B F E Industrial 2 of 5 / IATA C H H H S Interleaved 2 of 5 D I Z I S
3-7 Set 1 Set 2 Set 3 Set 4 Set 5 Plessey / MSI V V D P M Code 11 J J J J J Codabar / NW 7 F N X N F Matrix 2 of 5 E G G G S Code 39 / Code 32 A C Y M A Code 93 I L L L G Code 128 H K K K C Code 4 U U U U U Korea Code 3 of 5 R R R R R RSS R R R R R UCC128 / EAN128 W W W W W 3.2.1.4 BarCode Setup A. First select barcode type then select barcode to setting. B. Press “Default” button to reset all configuration setting of this barcode into default values. C. Press “Apply” button to be decided setting of this barcode. Please see 3.2.2 Symbologies List for more detail information of each Barcode. Figure 3-5 BarCode Setup
3-8 3.2.2 Symbologies List A Type -- Numeric-only Barcodes 3.2.2.1 UPC-E Figure 3-6 UPC-E Table 3-5 UPC-E Explaining Item Explaining Ignore 1st digit Do not transmit 1st digit by barcode. Format Transmit 1st digit Transmit 1st digit by barcode. Send Check Digit Whether send check digit by barcode.
3-9 3.2.2.2 UPC-A UPC-A movements together with EAN-13, so only Enable EAN-13 then UPC-A will be Enable, too. Figure 3-7 UPC-A Table 3-6 UPC-A Explaining Item Explaining Ignore 1st & 2nd digits Do not transmit 1st digit by barcode. Transmit 1st digit Transmit 1st digit by barcode. Transmit 2nd digit Transmit 2nd digit by barcode. Format Transmit 1st & 2nd digits Transmit 1st & 2nd digits by barcode. Send Check Digit Whether send check digit by barcode.
3-10 3.2.2.3 EAN-13 / ISBN Figure 3-8 EAN-13 / ISBN Table 3-7 EAN-13 / ISBN Explaining Item Explaining Ignore 1st & 2nd digits Do not transmit 1st digit by barcode. Transmit 1st digit Transmit 1st digit by barcode. Transmit 2nd digit Transmit 2nd digit by barcode. Format Transmit 1st & 2nd digits Transmit 1st & 2nd digits by barcode. Send Check Digit Whether send check digit by barcode. Enable ISBN Code Whether use this ISBN Code.
3-11 3.2.2.4 EAN-8/JAN-8 Figure 3-9 EAN-8/JAN-8 Table 3-8 EAN-8/JAN-8 Explaining Item Explaining Ignore 1st digit Do not transmit 1st digit by barcode. Format Transmit 1st digit Transmit 1st digit by barcode. Send Check Digit Whether send check digit by barcode. Convert to EAN-13 When this option is selected the scanner will convert EAN-8 to EAN-13 by transmitting five zeroes … Ahead of code Add five zeroes at prefix of the barcode. Add five 0 After 3 digits Add five zeroes after 3rd digits.
3-12 3.2.2.5 UPC-EAN Add on 2/5 A. UPC-E, UPC-A, EAN-13 / ISBN and EAN-8 / JAN-8 may all include an additional barcode to the right of the main barcode. B. This barcode will show primary & additional code together. C. So the UPC-EAN Add-ON 2/5 code is unable to use alone, must operate in UPC-E or UPC-A or EAN-13 / ISBN or EAN-8 / JAN-8. Figure 3-10 UPC-EAN Add on 2/5 Table 3-9 UPC-EAN Add-On 2/5 Explaining Item Explaining Only read the code with Addon 2/5 Only reads the codes that have addenda.
3-13 3.2.2.6 Industrial 2 of 5 / IATA Figure 3-11 Industrial 2 of 5 / IATA Table 3-10 Industrial 2 of 5 / IATA Explaining Item Explaining Send Check Digit Whether send check digit by barcode. Enable IATA Code Whether use this IATA Code. Checksum Verify Whether verify checksum by barcode. Min Length can be set from 2 to 48 Min-Max (Default: 2 / 48) Max Length can be set from 2 to 48 Length 1 can be set from 2 to 48 Length 2 can be set from 2 to 48 Length Fixed Length 3 can be set from 2 to 48
3-14 3.2.2.7 Interleaved 2 of 5 Figure 3-12 Interleaved 2 of 5 Table 3-11 Interleaved 2 of 5 Explaining Item Explaining Send Check Digit Whether send check digit by barcode. Checksum Verify Whether verify checksum by barcode. Min Length can be set from 4 to 48 Min / Max (Default: 4 / 48) Max Length can be set from 4 to 48 Length 1 can be set from 4 to 48 Length 2 can be set from 4 to 48 Length Fixed Length 3 can be set from 4 to 48
3-15 3.2.2.8 Plessey / MSI Figure 3-13 Plessey / MSI Table 3-12 Plessey / MSI Explaining Item Explaining Mode 10 Mode 10-10 Format Mode 11-10 Checksum mode for this barcode. Send Check Digit Whether send check digit by barcode. 1 Digit Check 1 digit & send by checksum. 2 Digits Check 2 digits & send by checksum.
3-16 3.2.2.9 Code11 Figure 3-14 Code 11 Table 3-13 Code 11 Explaining Item Explaining Send Check Digit Whether send check digit by barcode. 1 Digit Check 1 digit & send by checksum. 2 Digits Check 2 digits & send by checksum.
3-17 3.2.2.10 Codabar / NW7 Figure 3-15 Codabar / NW7 Table 3-14 Codabar / NW7 Explaining Item Explaining Start / Stop Digit Whether transmit Start & Stop Digit. ABCD abcd TN*E tn*e Start / Stop transmit type Checksum Verify Whether verify checksum by barcode.
3-18 3.2.2.11 Matrix 2 of 5 Figure 3-16 Matrix 2 of 5 Table 3-15 Matrix 2 of 5 Explaining Item Explaining Send Check Digit Whether send check digit by barcode. Checksum Verify Whether verify checksum by barcode. Min Length can be set from 4 to 48 Min-Max (Default: 4 / 48) Max Length can be set from 4 to 48 Length 1 can be set from 4 to 48 Length 2 can be set from 4 to 48 Length Fixed Length 3 can be set from 4 to 48
3-19 B Type -- Alphanumeric Barcodes 3.2.2.12 Code39 / Code32 Figure 3-17 Code39 / Code32 Table 3-16 Code39 / Code32 Explaining Item Explaining Code39 Standard Enable Code 39 Standard characters Code39 Full ASCII Enable Code 39 Full ASCII character Format Code32 Enable Code 32 Start / Stop Digit Whether transmit Start & Stop Digit. Verify Whether verify checksum by barcode. Checksum Transmit Whether transmit checksum by barcode.
3-20 3.2.2.13 Code93 The barcode do not have setting. Figure 3-18 Code93 3.2.2.14 Code128 / UCC EAN128 Figure 3-19 Code 128 / UCC EAN128 Table 3-17 Code128 / UCC EAN128 Explaining Item Explaining Enable UCC128/EAN128 Enable UCC128/EAN128.

Navigation menu