Shin Chuan Computer SC800PDT-BWG Portable Data Terminal User Manual

Shin Chuan Computer Co., Ltd. Portable Data Terminal

User Manual

Shin Chuan Computer User’s Manual SC800/SC820 SC800/SC820 User’s Manual WinCE Rugged Portable Data Terminal July/10/2009 Ver: 1.0
Shin Chuan Computer User’s Manual SC800/SC820 Revision History: Date Description Remark2008/12/18 Modified the contents of ch.3 and Appendix A GPRS Function 2009/2/16 Modified the contents of 2.5.8 Installing the SD Card 2009/6/16 Added Appendix B Expansion Module Applicability(RFID, GPS) 2009/6/19 Added “ Note: Wireless LAN, 2.4GHz Low Power Hyper and GPRS/EDGE cannot be used at the same time.” on Page 1-9 2009/7/10 Added Appendix C 2D Barcode Scanner Setting 2009/07/15 Added SAR Statement for FCC Certificate
Shin Chuan Computer User’s Manual SC800/SC820 Table of Contents Chapter 1. Introduction ............................................................................1-1 1.1 About this Manual.................................................................1-1 1.2 User and Product Safety ......................................................1-2 1.3 Battery Safety.......................................................................1-3 1.4 CE Statement .......................................................................1-4 1.4.1 Europe – EU Declaration of Conformity.......................1-4 1.5 FCC Statement.....................................................................1-8 1.5.1 FCC Interference Statement ........................................1-8 1.5.2 Hand-Operated Device SAR Evaluation: .....................1-9 1.6 Recycling & disposal instructions. ......................................1-10 1.7 Regulatory information. ......................................................1-10 1.8 Product Labeling ................................................................1-11 1.9 System Specifications ........................................................1-15 1.10 Environment Standard......................................................1-17 1.11 Warranty and after service................................................1-17 Chapter 2. Getting Started........................................................................2-1 2.1 Check the package...............................................................2-1 2.2 General View of the PDT......................................................2-3 2.2.1 SC800 general view.....................................................2-3 2.2.2 SC820 general view.....................................................2-5 2.3 Charging the Battery Pack ...................................................2-7 2.3.1 Installing the battery pack ............................................2-7 2.3.2 Charging the battery pack with Power Adapter ............2-9 2.4. Handling the PDT..............................................................2-10 2.4.1 Starting the PDT.........................................................2-10 2.4.2 Power on / off.............................................................2-10 2.4.3 Calibration of the touch Screen..................................2-11 2.4.4 To mute the Sound for SC800....................................2-11 2.4.5 Adjusting the Sound for SC820..................................2-11 2.4.6 Using the Stylus .........................................................2-12 2.4.7 Using the SC800 Keypad...........................................2-12 2.4.8 Using the SC820 Keypad...........................................2-14 2.4.9 Using the Ear/Microphone .........................................2-17
Shin Chuan Computer User’s Manual SC800/SC820 2.5 Navigating the Display........................................................2-18 2.5.1 Setting Time and Date ...............................................2-18 2.5.2 Entering the Data.......................................................2-18 2.5.3 The Command Bar.....................................................2-19 2.5.4 The Task Bar..............................................................2-19 2.5.5 The Soft Keypad ........................................................2-20 2.5.6 Setting Up Wireless LAN ...........................................2-20 2.5.7 Reading barcodes, 1D laser version..........................2-26 2.5.8 Reading barcodes, 2D CMOS version.......................2-27 2.5.9 Installing the SD Card................................................2-29 2.5.10 Help .........................................................................2-30 2.6 Power management ...........................................................2-30 2.6.1 Suspend Mode...........................................................2-30 2.6.2 Resuming...................................................................2-31 2.7 Resetting the PDT..............................................................2-31 2.7.1 Software (Warm) Reset..............................................2-31 2.7.2 Cold Reset .................................................................2-32 Chapter 3. Setting .....................................................................................3-1 3.1 Introduction ..........................................................................3-1 3.2 Control Panel .......................................................................3-1 3.2.1 BarCode Setting...........................................................3-1 3.2.2 Symbologies List..........................................................3-7 3.2.3 Bluetooth Device Properties ......................................3-23 3.2.4 Certificates.................................................................3-27 3.2.5 Control Center............................................................3-29 3.2.6 Date/Time ..................................................................3-34 3.2.7 Dialing Properties.......................................................3-34 3.2.8 Display Properties......................................................3-36 3.2.9 Input Panel.................................................................3-38 3.2.10 Internet Options .......................................................3-39 3.2.11 Keyboard..................................................................3-41 3.2.12 Network and Dial-up Connections............................3-42 3.2.13 Owner ......................................................................3-46 3.2.14 Password .................................................................3-48 3.2.15 PC Connection.........................................................3-48 3.2.16 Power.......................................................................3-49 3.2.17 Regional Settings.....................................................3-52
Shin Chuan Computer User’s Manual SC800/SC820 3.2.18 Remove Programs...................................................3-52 3.2.19 Storage Manager .....................................................3-53 3.2.20 Stylus .......................................................................3-54 3.2.21 System.....................................................................3-56 3.2.22 Terminal Server Client Licenses..............................3-58 3.2.23 Volume & Sounds Properties ...................................3-58 3.3 Taskbar and Start Menu .....................................................3-59 Chapter 4. Communication ......................................................................4-1 4.1 Installing & Setting Up Microsoft ActiveSync ........................4-1 4.1.1 Installing Microsoft ActiveSync on the Host PC............4-1 4.1.2 Connecting PDT to Host PC ........................................4-1 4.2 Using ActiveSync .................................................................4-1 4.2.1 Setting up a Partnership ..............................................4-1 4.2.2 ActiveSync File Synchronization ..................................4-3 4.3 Networking ...........................................................................4-3 Chapter 5. Software Applications............................................................5-1 5.1 Introduction ..........................................................................5-1 5.2 Software Applications...........................................................5-1 5.2.1 Inbox............................................................................5-1 5.2.2 Internet Explorer ........................................................5-11 5.2.3 Messenger .................................................................5-14 5.2.4 Microsoft WordPad ....................................................5-14 5.2.5 Remote Connection ...................................................5-20 5.2.6 Windows Explorer......................................................5-21 5.3 DiskOnChip ........................................................................5-23 5.3.1 Saving to Flash ..........................................................5-23 5.3.2 DiskOnChip Location .................................................5-23 5.3.3 DiskOnChip Size........................................................5-24 Appendix A GPRS Function ..................................................................... A-1 A.1 Using the GPRS Features .................................................. A-1 A.1.1 SIM Card .................................................................... A-1 A.1.2 Inserting a SIM Card................................................... A-1 A.1.3 Before Start: ............................................................... A-2 A.2 Select settings .................................................................... A-4 A.3 Internet connection ............................................................. A-8
Shin Chuan Computer User’s Manual SC800/SC820 A.3.1 Connecting ................................................................. A-8 Appendix B Expansion Module Applicability.......................................... B-1 B.1 RFID Applicability................................................................ B-1 B.2 GPS Applicability ................................................................ B-3 Appendix C 2D Barcode Scanner Setting ............................................... C-1 C.1 Basic Tab ............................................................................ C-1 C.2 Code Configure Tab............................................................ C-1 C.3 Prefix and Suffix Tab...........................................................C-2 C.4 Quiet Zone Tab ................................................................... C-3 C.5 Read Mode Tab ..................................................................C-3 C.6 ASCII Conversion Tab......................................................... C-4 C.7 Advanced Tab ..................................................................... C-4 C.8 Firmware Upgrade Tab ....................................................... C-5
Shin Chuan Computer User’s Manual SC800/SC820 1-1 Chapter 1. Introduction Congratulations on purchasing the SC800/SC820 Portable Data Terminal (PDT), a Microsoft Windows®CE Rugged PDT. Its special combination of features makes it perfect for using in a wide range of applications. These features as: Intel® XScaleTM PXA270 520MHz 32 bits RISC Processor Windows® CE 5.0 Operating System 128MB SDRAM & 256MB/1GB Flash ROM Open Architecture: User Accessible SD Slot 240 x 320, 3.5” Color TFT Display with Touch Panel One Numeric-Alpha Keyboards with LED backlight 802.11b/g Radio Support 2.4GHz Low Power Hyper: V2.0+EDR, Class II Support IrDA Support Optionally Built-in GPRS/EDGE Module Integrated 1D Barcode Scanner Integrated 2D Barcode Scanner 1.1 About this Manual The following chapters contained in this manual are: Chapter 1: Introduction General information about the PDT. Chapter 2: Getting started Describe the basic use of the PDT. Chapter 3: Setting Provide basic instructions for customizing the PDT. Chapter 4: Communication Describe how to use all kinds of communication of the PDT. Chapter 5: Software Application Describe the installed applications on the PDT. Appendix A. Appendix B Appendix C GPRS Function Expansion Module Applicability 2D Barcode Scanner Setting Provide instructions for the GPRS Service Provide instructions for the Expansion Module Applicability Provide instructions for the 2D BarcodeScanner
Shin Chuan Computer User’s Manual SC800/SC820 1-2 1.2 User and Product Safety z Do not stare into the laser or LED beam directly or shine it into eyes. z Never use strong pressure onto the screen or subject it to severe impact, as the LCD panel could become cracked and possibility cause personal injury. If the LCD panel is broken, never touch the liquid inside because the liquid irritates the skin. z Although the PDT has passed the test of IP65 standard for water and dust resistance, avoid prolonged exposure to rain or other concentrated moisture. Such condition exceeds the IP65 standard, and could result in water or other contaminants entering into the PDT. z Use only the original approved AC Adapter with the PDT. Use of an unapproved AC Adapter could result in electrical problems, or even cause a fire or electrical shock to the user. z Do not disassemble the PDT. Servicing should be done by supplier only. If the PDT or accessories gets damaged due to wrong handling or unauthorized repair, warranty is void. In case the warranty seals are broken, warranty is void too. z Make regularly back-up of all important data. z Under no circumstance will supplier be liable for any direct, indirect, consequential or incidental damages baring out of the use or inability to use the hardware and software and/or any data loss, even if supplier has been informed about the possibility of such damages. z LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT
Shin Chuan Computer User’s Manual SC800/SC820 1-3 1.3 Battery Safety CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions. Lithium-ion battery packs might get hot, explode, ignite and/or cause serious injury if exploded by abusive using. Please follow the safety warnings listed as below: z Do not throw the battery pack in fire. Do not expose the battery to high temperatures. z Do not connect the positive battery pack with negative battery pack to each other with any metal object (like wire). z Do not carry or store battery pack together with metal objects. z Do not pierce the battery pack with nails or drills, strike the battery pack with a hammer, step on the battery pack or otherwise expose it to strong impacts, shocks or excessive force. z Do not solder onto the battery pack. z Do not expose battery pack to liquid or allow the battery contacts to get wet. z Do not disassemble or modify the battery pack. The battery pack contains safety and protection measures, which, if damaged, may cause the battery pack to generate heat, explode or ignite. z Do not discharge the battery pack using any device except for the specified device. When it is used in devices other than the specified devices, the battery pack can be damaged or its life expectancy reduced. If the device causes any abnormal current to flow, it may cause the battery pack to become hot, explode or ignite and cause serious injury. z In the event the battery pack leaks and the fluid gets into one’s eye, do not rub the eye. Rinse well with water and immediately seek medical care. If left untreated, the battery fluid could cause damage to the eye.
Shin Chuan Computer User’s Manual SC800/SC820 1-4 1.4 CE Statement 1.4.1 Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN 60950-1: 2006 Safety of Information Technology Equipment - EN50360 : (2001-07) Product standard to demonstrate the compliance of mobile phones with the basic restrictions related to human exposure to electromagnetic fields (300 MHz-3GHz) - EN50361 : (2001-07) Basic standard for the measurement of specific absorption rate related to human exposure to electromagnetic fields from mobile phones (300 MHz-3 GHz) - EN50371 : (2002-03) Generic standard to demonstrate the compliance of low power electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (10 MHz-300 GHz) -- General public - EN 300 328 V1.7.1: (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive - EN 301 511 V9.0.2: (2003-03) Global System for Mobile communications (GSM); Harmonized standard for mobile stations in the GSM 900 and DCS 1800 bands covering essential requirements under article 3.2 of the R&TTE directive (1999/5/EC)
Shin Chuan Computer User’s Manual SC800/SC820 1-5 - EN 301 489-1 V1.6.1: (2005-09) Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements - EN 301 489-17 V1.2.1 (2002-08) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment - EN 301 489-7 V1.2.1: (2002-08) ElectroMagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment ad services; Part 7: Specific conditions for mobile and portable radio and ancillary equipment of digital cellular radio telecommunications systems (GSM and DCS) This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. 0560 Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Shin Chuan Computer User’s Manual SC800/SC820 1-6 Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hierbij verklaart [naam van de fabrikant] dat het toestel [type
Shin Chuan Computer User’s Manual SC800/SC820 1-7 Nederlands [Dutch] van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese] [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Shin Chuan Computer User’s Manual SC800/SC820 1-8 1.5 FCC Statement 1.5.1 FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. IMPORTANT NOTE: For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with the (Shin Chuan Computer Co., Ltd.) accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating
Shin Chuan Computer User’s Manual SC800/SC820 1-9 instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter except built-in tested devices. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. Note: Wireless LAN, 2.4GHz Low Power Hyper and GPRS/EDGE cannot be used at the same time. Caution: SCC declares that SC800 ( FCC ID: TQ2-SC800PDT-BWG ) / SC820 ( FCC ID: TQ2-SC800PDT-BWG ) is limited in CH1~CH11 for 2.4GHz by specified firmware controlled in U.S.A. The FCC ID of SC800/SC820 is TQ2-SC800PDT-BWG 1.5.2 Hand-Operated Device SAR Evaluation:
Shin Chuan Computer User’s Manual SC800/SC820 1-10 LED AND LASER SAFETY INFORMATION z Class I LED/ Class II Laser Product z Do not stare at the LED/Laser or shine into eyes z Do not allow young children to use the product without adult supervision z Do not replace/repair the LED/Laser, these are not user replaceable z Do not shine the LED/Laser on a shiny reflective surface z LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT 1.6 Recycling & disposal instructions. Do not throw this product in the home waste bin. 1.7 Regulatory information. For CE, FCC, RoHS and other Document of Conformities, consult the Contact Window of Shin Chuan Computer.
Shin Chuan Computer User’s Manual SC800/SC820 1-11 1.8 Product Labeling The PDT has several labels as showed in Figure 1-1 to 1-4. A. SC800 Figure 1-1 Product Labeling (Front side view) Label nr. Description 1 LCD panel protection film 2 SC800 logo 3 Warranty seal PDT Table 1-1 Front labeling
Shin Chuan Computer User’s Manual SC800/SC820 1-12 Figure 1-2 Product Labeling (Back side view) Label nr. Description 4 Laser radiation warning label 5 Serial / Configuration number 6 PenPower label (only use on Simplified Chinese version) 7 CCC label (only use with China) 8 System and regulatory label 9 NCC label (only use on Traditional Chinese version) 10 RoHS Use Life Label for China 11 Windows CE .NET label Table 1-2 Rear labeling
Shin Chuan Computer User’s Manual SC800/SC820 1-13 B. SC820 Figure 1-3 Product Labeling (Front side view) Label nr. Description 1 LCD panel protection film 2 SC820 logo 3 Warranty seal PDT Table 1-3 Front labeling
Shin Chuan Computer User’s Manual SC800/SC820 1-14 Figure 1-4 Product Labeling (Back side view) Label nr. Description 4 LED/Laser radiation warning label 5 Serial / Configuration number 6 PenPower label (only use on Simplified Chinese version) 7 CCC label (only use with China) 8 System and regulatory label 9 NCC label (only use on Traditional Chinese version) 10 RoHS Use Life Label for China 11 Windows CE .NET label Table 1-4 Rear labeling
Shin Chuan Computer User’s Manual SC800/SC820 1-15 1.9 System Specifications The SC800 / SC820 detailed specifications as follows. Unless otherwise noted, all the specifications are subject to change without prior notification. Table 1-5 System Specification SC800 / SC820 Processor - Intel PXA270 520MHz 32 bits RISC CPU Memory - 256MB/1GB Flash ROM - 128MB SDRAM Display - 240 x 320 3.5” TFT 256K Color LCD with LED backlight Audio - One mono speaker for system voice (on lower case) - One 2.5 mm Ø stereo earphone jack with mono mike input - One internal MIC - One Receiver Expansion Slot - One SD/MMC slot (only support SD memory) - One SIM slot for WAN module LED - One Dual-Color LED for Charger Indicator - One Dual-Color LED for Scanner Indicator Radio Support - Wireless LAN: 802.11b/g - 2.4GHz Low Power Hyper: V2.0+EDR, Class II - IrDA: 1.2 Scan Engine - Opticon Laser (1D) Engine. (Symbol optional) Communication Ports - USB: Support USB v1.1 both host and client. (PDT and Cradle) - Serial: RS232 via optional cable or Cradle. Power System - Standard Li-Ion Battery Pack, 3.7VDC/2200mAh - Advanced Smart Battery with Gas-Gauge - Built-in Battery Charger - 3.7VDC/80mAh rechargeable backup battery - One Battery Cover Sensor Switch - Power Adapter: 100~240VAC, 50/60Hz Input ; 5VDC/2.6A Output
Shin Chuan Computer User’s Manual SC800/SC820 1-16 SC800 / SC820 SC800 - One Power Button - One Reset Button - Three Barcode Scanner Buttons - Two Navigation Buttons - Four Application Buttons - One 18-key Numeric Keypad - One Reserved Button Keypad / Buttons SC820 - One Power Button - One Reset Button - Three Barcode Scanner Buttons - Two Navigation Buttons - Four Application Buttons - One 33-key Alpha-Numeric Keypad - One Reserved Button Dimensions and Weight - Dimensions: L: 155mm, W: 82mm, H: 31~33mm - Weight: 375g with Standard Battery Pack (Approx.) Color - Black Peripherals and Accessories - Optional: RS232 Serial Cable for Terminal / USB Host Cable for Terminal / High-Capacity Li-Ion Battery Pack (3.7VDC/4000 mAh) / Single Dock / 4 Slot Battery Charger / Car Adapter / RS232 Cable / Pistol Grip Software - Microsoft Windows CE 5.0 Professional
Shin Chuan Computer User’s Manual SC800/SC820 1-17 1.10 Environment Standard Table 1-6 Environment Standards Operating Temperature 14oF ~ 122oF( -10oC ~ 50oC) Storage Temperature -4oF ~ 158oF (-20oC ~ 60oC) Humidity 5% ~ 95% (non-condensing) Drop 5ft (1.5m) Drop onto Concrete Water & Dust proof IP65 Certificated Vibration MIL STD 810F 1.11 Warranty and after service Should this PDT be malfunctioned, please contact your original retailer providing information about the product name, the serial number, and the details about the problem.
Shin Chuan Computer User’s Manual SC800/SC820 2-1 Chapter 2. Getting Started 2.1 Check the package Open the package and check all the parts are inside without shortage and damage: A. SC800 Figure 2-1 Inside the package 1. SC800 Terminal 2. Standard Battery Pack (3.7VDC/2200mAh) 3. USB Client Cable for Terminal 4. AC Power Cord 5. Standard AC Adapter 5VDC/2.6A 6. Earphone/ Microphone Set 7. Quick Guide (not shown in the picture)
Shin Chuan Computer User’s Manual SC800/SC820 2-2 B. SC820 Figure 2-2 Inside the package 1. SC820 Terminal 2. Standard Battery Pack (3.7VDC/2200mAh) 3. USB Client Cable for Terminal 4. AC Power Cord 5. Standard AC Adapter 5VDC/2.6A 6. Earphone/ Microphone Set 7. Quick Guide (not shown in the picture)
Shin Chuan Computer User’s Manual SC800/SC820 2-3 2.2 General View of the PDT 2.2.1 SC800 general view Figure 2-3 SC800 front side view Figure 2-4 SC800 back side view
Shin Chuan Computer User’s Manual SC800/SC820 2-4 Table 2-1 Description of SC800 General View “Red” color Reading barcode 1 Scanner LED Indicator “Green” color Successful reading “Red” color Charging battery 2 Charge LED Indicator “Green” color Battery charged full “Blue” color 2.4GHz Low Power Hyper or WLAN Enable 3 3 color LED Indicator “Green” color GPRS Enable 4 LCM / Touch Panel Do specific action through touch panel by stylus5 Left Scan key Right Scan key Scan key Start scanning the barcode by pressing any one of these three scan keys 6 Power key Puts the terminal into and wakes the terminal from suspend mode. 7 F1 ~ F4 key The four application keys, hot keys of application program defined by end user. 8 Navigation key Navigation keys for left, right, up and down directions 9 Alpha-Numeric keys Numeric keys, Change to Alpha keys after pressing Alpha key. 10 Alpha key Toggle Alpha-mode for Alpha-Numeric keys 11 Fn key This key is used in combination with other keys to type special characters and perform system functions. 12 Enter key This key confirms data entry 13 Earphone Jack Connector A connector to plug a earphone 14 USB / Serial / Synchronization port A connector to support USB Host/Client and serial functions 15 Scan window A window for scanning of barcode reader 16 Stylus Use the stylus for selecting items and entering information. 17 Battery Cover Protect Battery pack, keep the switch of battery cover to leave system from suspend mode 18 Battery cover Latch To keep Battery Cover locked 19 Hand Strap This strap can be sealed tighter or looser 20 Speaker 1W speaker for audio sound 21 DC Power Jack A connector to support AC power. 22 IrDA A module to support IrDA function
Shin Chuan Computer User’s Manual SC800/SC820 2-5 2.2.2 SC820 general view Figure 2-5 SC820 front side view Figure 2-6 SC820 back side view
Shin Chuan Computer User’s Manual SC800/SC820 2-6 Table 2-2 Description of SC820 General View “Red” color Reading barcode 1 Scanner LED Indicator “Green” color Successful reading “Red” color Charging battery 2 Charge LED Indicator “Green” color Battery charged full “Blue” color 2.4GHz Low Power Hyper or WLAN Enable 3 3 color LED Indicator “Green” color GPRS Enable 4 LCM / Touch Panel Do specific action through touch panel by stylus5 Left Scan key Right Scan key Scan key Start scanning the barcode by pressing any one of these three scan keys 6 Power key Puts the terminal into and wakes the terminal from suspend mode. 7 F1 ~ F4 key The four application keys, hot keys of application program defined by end user. 8 Navigation key Navigation keys for left, right, up and down directions 9 Alpha keys Alpha key. 10 Numeric keys Numeric keys. 11 Fn key This key is used in combination with other keys to type special characters and perform system functions. 12 Enter key This key confirms data entry 13 Earphone Jack Connector A connector to plug a earphone 14 USB / Serial / Synchronization port A connector to support USB Host/Client and serial functions 15 Scan window A window for scanning of barcode reader 16 Stylus Use the stylus for selecting items and entering information. 17 Battery Cover Protect Battery pack, keep the switch of battery cover to leave system from suspend mode 18 Battery cover Latch To keep Battery Cover locked 19 Hand Strap This strap can be sealed tighter or looser 20 Speaker 1W speaker for audio sound 21 DC Power Jack A connector to support AC power. 22 IrDA A module to support IrDA functions
Shin Chuan Computer User’s Manual SC800/SC820 2-7 2.3 Charging the Battery Pack Before using the PDT, perform the basic procedure of charging the battery pack through the following steps. 2.3.1 Installing the battery pack 1. On the PDT attached with a hand-strap, detach and loose the hand-strap. Figure 2-7 Release the Hand strap from PDT 2. Turn the locking latches (right and left) downwards and lift the battery cover away from the PDT. Figure 2-8 Detach the battery cover from PDT
Shin Chuan Computer User’s Manual SC800/SC820 2-8 3. Insert the battery pack into the battery compartment with the label facing out, and ensuring the battery snaps into place. Figure 2-9 Insert the battery pack 4. Replace the battery cover by inserting the top first, and then press the bottom in firmly. Turn the locking latches (right and left) upwards to secure the cover to the PDT. Figure 2-10 Replace the battery cover 5. Charge time. For the first time to charge the battery pack needs approximately 6 hours. Subsequent charging time needs approximately 4 hours.
Shin Chuan Computer User’s Manual SC800/SC820 2-9 ◆. When charging the battery pack, the charge LED indicator on the PDT turns on Red. After the battery pack is fully charged, the charge LED indicator turns to Green. 2.3.2 Charging the battery pack with Power Adapter 1. Connect the Power cord to the Power adapter. 2. Plug in the connector of the power adapter. 3. Connect the power cord to a power source. Figure 2-11 Charging with power adapter ◆ When charging the battery pack, the charge LED indicator on the PDT turns on Red. ◆ After the battery pack is fully charged, the charge LED indicator turns to Green. CAUTION: Please do not remove the Battery pack too long from PDT after you have already full-charged the Battery pack and backup battery pack and start to use the PDT. Otherwise non-saved data will be lost. Please also keep in mind power the PDT off if you want to change the main Battery pack. PDT Main Unit Charger LED Indicator Power Cord Power Adapter
Shin Chuan Computer User’s Manual SC800/SC820 2-10 2.4. Handling the PDT 2.4.1 Starting the PDT Press the Power key to turn on/off the PDT. If the PDT does not power on, perform a cold boot. See 2-7 Resetting the PDT. CAUTION: When a battery is fully inserted in PDT for the first time, upon the PDT’s first power up, the device boots and powers on automatically. Figure 2-12 Starting the PDT 2.4.2 Power on / off ¾ To turn on the PDT Press the Power key briefly ( ). If the PDT does not power on, perform the cold reset. See chapter 2.7.1. As the PDT initializes its file system, it splash screen displays for about 30 seconds followed by calibration screen. Every time you perform a cold reset, these screens will also appear. To turn off the PDT, just press the Power key again. This action does not actually turn off the PDT, it only turns the PDT into suspend mode. All running applications remain as you left them, until you press the Power key again to resume operation of the PDT When the PDT is powered on for the first time, it initializes its system. A splash screen (figure 2-12) appears for a short period of time followed by the WinCE 5.0 window. This section offers the basic procedures of PDT using.
Shin Chuan Computer User’s Manual SC800/SC820 2-11 2.4.3 Calibration of the touch Screen On the initial boot-up of the PDT, the stylus calibration screen (Labeled Align Screen) opens. Use the stylus to press and hold briefly on the center of each target as it moves around the screen. If necessary, adjust the backlight on the PDT to make the screen readable. (See below 2.4.4. Adjust the brightness). When you feel the touch screen function is poor or the operation does not match the exact location it should be, please recalibrate the screen by using the stylus to tap the Start > Settings > Figure 2-13 Calibration Control Panel > Stylus, to open the “Calibration” to recalibrate again. 2.4.4 To mute the Sound for SC800 To mute the sound, press the key first, and then press the key to turn off and turn on the sound. 2.4.5 Adjusting the Sound for SC820 The factory default for the sound is in Middle level. You can adjust the sound to meet your environment and comfort as: 1) Increase high voice: Press the key and then press the key to increase high voice. 2) Decrease low voice: Press the key and then press the key to decrease low voice.
Shin Chuan Computer User’s Manual SC800/SC820 2-12 2.4.6 Using the Stylus The stylus is located next to hand-strap on the left rear of the PDT. The stylus function is same as the mouse on a PC. Use the stylus to: 1) Navigate the display, select menu item and open optional applications. 2) Tap the characters on soft keyboard panel. 3) Hold the stylus on the screen and drag across the screen to select the list of multiple items. CAUTION: Never use a pen, pencil, or other sharp object on the display to avoid any unexpected damage of the touch screen. 2.4.7 Using the SC800 Keypad Figure 2-14 SC800 Keypad Table 2-3 Keypad List Key Main Function Fn + Main Function Alpha + Caps + Main Function Main BarCode Scan Key Power On/Off Internet Explorer Microsoft WordPad
Shin Chuan Computer User’s Manual SC800/SC820 2-13 Key Main Function Fn + Main Function Alpha + Caps + Main Function Inbox File Explorer Up Left Down Right TAB (Tabulation) ESC Caps Audio Mute Function change Change to letters Backspace 1 ＠ (at) ： ＼ 2 ’ (Quotation Marks) A B C 3 ＋ (Plus Sign) D E F 4 Paste G H I 5 Del (Delete) J K L 6 － (Minus Sign) M N O 7 Copy P Q R S 8 ＆ (AND) T U V 9 X (Multiplication) W X Y Z 0 Space ［ ］ ＊ (Asterisk) Start Menu . ， ； ＃ ／ (Division) ＝ ％ Enter Table 2-4 Special Assembler Key Assembler Key Functionality Definition Reset Key Warm Reset Press “Reset” button in the back. + Reset Key Cold Reset Press “Power” and “Reset” button simultaneously.
Shin Chuan Computer User’s Manual SC800/SC820 2-14 2.4.8 Using the SC820 Keypad Figure 2-15 SC820 Keypad Table 2-5 Keypad List Key Main Function Fn + Main Function Caps + Main Function Main Barcode Scan Key Power On/Off Internet Explorer Microsoft WordPad Inbox File Explorer Up Left Down Right Esc Tab Tab Backspace Del Backspace Caps Start Menu Enable/Disable Caps function
Shin Chuan Computer User’s Manual SC800/SC820 2-15 Key Main Function Fn + Main Function Caps + Main Function Enter Function change Space a ~ A b $ B c + C d 1 D e 2 E f 3 F g ! G h % H i － (Minus Sign) I j 4 J k 5 K l 6 L m Copy M n @ N
Shin Chuan Computer User’s Manual SC800/SC820 2-16 Key Main Function Fn + Main Function Caps + Main Function o \ O p ＊ P q 7 Q r 8 R s 9 S t Paste T u # U v & V w / W x . (Point) X y 0 Y z = Z Table 2-6 Special Assembler Key Assembler Key Functionality Definition Reset Key Warm Reset Press “Reset” button in the back. + Reset Key Cold Reset Press “Power” and “Reset” button simultaneously.
Shin Chuan Computer User’s Manual SC800/SC820 2-17 2.4.9 Using the Ear/Microphone Connect Ear/Microphone to PDT earphone jack connector. The PDT has built in microphone; but if you do want to record the voice, you have to use the packed Ear/Microphone. Figure 2-16 Ear/Microphone
Shin Chuan Computer User’s Manual SC800/SC820 2-18 2.5 Navigating the Display 2.5.1 Setting Time and Date In the Date/Time options, you can change the year, month, date, time, time zone, or select automatic adjust for Daylight Saving Time. To set or change the date and time: 1. Select Start > Settings > Control Panel > Date/Time 2. To change the year, select the year or open a numeric dial. Select the up arrow to increase the value; select the down arrow to decrease the value. or you can type a new value in the field. 3. Select the month to open a pull-down list of months or press the arrow buttons to either side of the month to increase or decrease the month. 4. To change the time, select the hour, minute, seconds, or AM/PM and select the up arrow to increase the value; select /tape the down arrow to decrease Figure 2-17 Date/Time properties the value. Or you can type a new value in the field. 5. Select your correct time zone from the pull-down list. 6. To automatically adjust the clock for Daylight Saving Time, enable the checkbox at the bottom of the screen. 7. Select Apply to make save your changes [and make additional modifications] or select OK to exit the Date/Time settings. 2.5.2 Entering the Data To select and open programs, select Start > Programs from the task bar to open a list of available programs. Or if the program has a icon on the desktop, double-tap to open it. There are several ways to enter data on the PDT once in an application: z Use the keypad to enter alpha-numeric characters, Refer to “2.4.7 Using the SC800 keypad”. z Use the stylus on the touch screen.
Shin Chuan Computer User’s Manual SC800/SC820 2-19 z Select text in the same way you select the text on a PC. Use the stylus to highlight the desired text by dragging the stylus across the desired text, double-tapping to select one word and triple-rapping to select an entire line/paragraph. Refer to “2.5 Navigating the Display” starting. z Use the soft input panel (digital keyboard) with the stylus. z Use the bar code scanning to enter data. Press the trigger or “Barcode Scan” key to initiate a scan. The scanned data will enter the current application’s open file. Refer to “2.5.7 Reading barcodes, 1D laser version” starting for more information on using a scanner. For more information on factory installed applications, Refer to Chapter 4 “ Software Programs”. 2.5.3 The Command Bar Use the Command bar at top of the screen to perform tasks in programs, such a opening a file, or editing a file. Figure 2-18 Task Bar & Command Bar 2.5.4 The Task Bar The Task bar at the bottom of the screen displays the icon, an icon for the active program, the current time, and system icons for utilities loaded in memory. The Task bar includes menu names, buttons, and the keyboard icon, which opens and closes the soft input panel (SIP). The Task bar allows you to select and close programs. Refer to Figure 2-18 to view the Task bar. Command Bar Task Bar
Shin Chuan Computer User’s Manual SC800/SC820 2-20 2.5.5 The Soft Keypad In applications that accept keypad input, the soft input panel (SIP) can be used to enter data using the stylus. The SIP is digital, QWERTY-style keyboard. To open the SIP, tap the keyboard icon to open the menu and select Hide Input Panel to close the keyboard. Use the stylus to select letters, numbers, or symbols from the Soft Input Panel for the current application. 2.5.6 Setting Up Wireless LAN The Summit Client Utility (SCU) is an application designed for end users and administrators of mobile devices that use a Summit radio module. Using SCU, an end user can: z Disable the radio (turn it off) and enable the radio (turn it on) z View the contents of configuration profiles, or profiles, each of which houses the RF, security, and other settings for the radio z Select the profile to be used to connect to a WLAN z View global settings, which apply to every profile z View status information on the radio, the access point (AP) or WLAN router to which it is connected, and the RF connection or link between the two devices z To troubleshoot a connection or performance issue, view in-depth diagnostic information on the connection and the radio, and perform various troubleshooting and diagnostic tests After completing an administrator login to the utility, a user can perform these additional tasks: z Create, rename, edit, and delete profiles z Alter global settings, which apply to every profile SCU provides a graphical user interface (GUI) for access to all of its functions. Access to these functions also is available through an application programming interface (API), which an application programmer can use to enable another utility to manage the radio. To initialize SCU: z From the Start menu, select Programs z Select the directory called Summit
Shin Chuan Computer User’s Manual SC800/SC820 2-21 z Inside the Summit directory are two items: a directory for the storage of security certificates and an SCU icon. To run SCU, double-click the SCU icon SCU has five tabs: Main, Profile, Status, and Diags, and Global. Each tab is described in more detail in this section. Main Tab Figure 2-19 Main Tab z Enable/Disable Radio: When the radio is enabled, selecting this button disables it; when the radio is disabled, selecting this button enables it. z Active Profile: You can view the name of the active profile and, using the selection list, select a different profile. If you select “ThirdPartyConfig” then, after the device goes through a power cycle, WZC is used for configuration of the radio. z Status: Indicates the radio’s status. z Radio Type: Indicates the type of radio in the device. “BG” means a Summit radio that supports 802.11b and 802.11g. z Regulatory Domain: Indicates the regulatory domain or domains for which the radio is configured. “Worldwide” means that the radio can be used in any domain. The domain cannot be configured by an administrator or user. z Driver: Indicates the version of the device driver that is running on the device.
Shin Chuan Computer User’s Manual SC800/SC820 2-22 z SCU: Indicates the version of SCU that is running on the device. z About SCU: When tapped, supplies information on SCU that on a Windows application normally would appear under Help\About. Profile Tab Profile settings are radio and security settings that are stored in the registry as part of a configuration profile. When a profile is selected as the active profile on the Main tab, the settings for that profile become active. An administrator can define up to 20 profiles, edit them, and delete them on the Profile tab in SCU. Profile changes made on the tab are saved to the profile only when the Commit button is pressed. Unless it is modified, the Default profile does not specify an SSID, EAP type, or method of encryption. If the Default profile is the active profile, then the radio will associate only to an access point that broadcasts its SSID and requires no EAP type and no encryption. Figure 2-20 Profile Tab z Edit Profile: This is used to select the profile to be viewed or, if you are an administrator, edited. z Actions: Four actions are available, with the first three available only to an administrator: -New: Create a new profile with default settings and give it a unique name (and then change settings using other selections on the tab).
Shin Chuan Computer User’s Manual SC800/SC820 2-23 -Rename: Give the profile a new name, one that is not assigned to another profile -Delete: Delete the profile, provided that it is not the active profile. -Scan: Open a window that lists access points that are broadcasting their SSIDs. Each time you tap the Refresh button, you view an updated list of APs, with each row showing an AP’s SSID, its received signal strength indication (RSSI), and whether or not data encryption is in use (true or false). You can sort the list by clicking on the column headers. If you are authorized as an administrator, select an SSID in the list, and tap Commit, you return to the Profile tab to create a profile for that SSID. z Radio: Radio attributes in the list box can be selected individually. When an attribute is selected, the current setting or an appropriate selection box with the current setting highlighted appears on the right. z Security: Values for the two primary security attributes, EAP type and encryption type, are displayed in separate dropdown lists, with the current values highlighted. When you as an administrator select an EAP type, the Credentials button appears; when you tap it, a dialog box appears that enables you to define authentication credentials for that EAP type. When you as an administrator select an encryption type that requires the definition of WEP keys or a pre-shared key, the PSKs/WEP Keys button appears; when you tap it, a dialog box appears that enables you to define WEP keys or a PSK. z Commit: To ensure that changes to profile settings made on the tab are saved in the profile, you must tap the Commit button. To cause a Summit radio to connect to a typical business WLAN, you must select a profile that specifies the SSID, EAP type, and encryption type supported by the WLAN: z SSID: This is the name or identification of the WLAN. z EAP type: This is the protocol used to authenticate the device and its user if the WLAN uses the Enterprise version of Wi-Fi Protected Access (WPA) and WPA2. SCU supports five EAP types: PEAP with EAP-MSCHAP (PEAP-MSCHAP), PEAP with EAP-GTC (PEAP-GTC), EAP-TLS, LEAP, and EAP-FAST z Encryption: This specifies the type of key used to encrypt and decrypt transmitted data and how that key is specified or derived. Encryption options include:
Shin Chuan Computer User’s Manual SC800/SC820 2-24 - WPA2 or WPA with dynamic keys (derived from the EAP authentication process) - WPA2 or WPA with pre-shared keys - Static WEP keys Consult the user’s guide for details on all profile settings, including security settings. Status Tab The Status tab provides status information on the radio. z Active profile z Radio’s status: Down (not recognized), Disabled, Not Associated, Associated, or [EAP type] Authenticated z Client info: Name, IP address, and MAC address z AP info: Name, IP address, MAC address, beacon period, and DTIM interval z Connection info: Channel, data rate, transmit power, signal strength, and signal quality Figure 2-21 Status Tab
Shin Chuan Computer User’s Manual SC800/SC820 2-25 Diags Tab Figure 2-22 Diags Tab z (Re)connect: Disable and enable the radio, apply or reapply the current profile, and attempt to associate and authenticate to the wireless LAN, logging all activity in the output area at the bottom. z Release/Renew: Obtain a new IP address through DHCP release/renew, and log all activity in the output area at the bottom. z Start Ping: Start a continuous ping to the address in the edit box next to it. Once the button is clicked, its name and function will change to Stop Ping. Moving to an SCU window other than Status or Diags also will stop the ping, as will Pings will continue until you tap the Stop Ping button, move to an SCU window other than Diags or Status, exit SCU, or remove the radio. z Diagnostics: Attempt to (re)connect to an AP, and provide a more thorough dump of data than is obtained with (Re)connect. The dump will include radio state, profile settings, global settings, and a BSSID list of APs in the area. z Save To...: Save the diagnostics output to a file. Global Tab Global settings include: z Radio and security settings that apply to all profiles z Settings that apply to SCU itself
Shin Chuan Computer User’s Manual SC800/SC820 2-26 An administrator can define and change most global settings on the Global Settings Tab in SCU. Figure 2-23 Global Tab The default setting for each global setting ensures reliable operation in most environments. Consult the user’s guide for details on all global settings. 2.5.7 Reading barcodes, 1D laser version. To use the scanning function, complete the following steps: 1. If you have not already done so, remove the protective plastic film before using devices equipped with a 1D laser bar code reader. 2. Select Start > Setting > Control Panel > Barcode Setting; complete all configurations following all description of 3.2.1 BarCode Setting. 3. Run the WordPad software program. 4. Press one of the three barcode reader trigger buttons. 5. Aim the scanning beam at the center of barcode.
Shin Chuan Computer User’s Manual SC800/SC820 2-27 6. Good scanning position. The reading range is from 40 to 300mm distance. 1) Decrease the scanning distance to the bar code when scanning small barcodes. 2) Increase the scanning distance from the bar code when scanning large barcodes 3) The scanning area is visible by a red laser beam. 7. Bad scanning position. 1) Make sure that the laser beam sweeps across whole bar code. 2) Scanning operations may fail if the laser beam is positioned as below. 8. upon reading a barcode, the red LED indicator turns on until the trigger is release or after five seconds. The green LED and the beep tone indicates a good read. Note: This product scans using laser light. Never look directly into the laser light or shine the laser light into the eyes. 2.5.8 Reading barcodes, 2D CMOS version. The 2D CMOS version can read both 1D and 2D bar codes. To use the scanning function, complete the following steps: 1. If you have not already done so, remove the protective plastic film before using devices equipped with a 2D CMOS bar code reader. 2. Select Start > Setting > Control Panel > Barcode Scanner Settings 3. Run the WordPad software program. 4. Press one of the three bar code reader trigger buttons. 5. Aim the scanning beam at the center of bar code. To assists in aiming, there are 4 green aiming light spots. The bar code should be between the outside 2 green spots. The scanner is in focus in case the center 2 green spots joins into 1 spot.
Shin Chuan Computer User’s Manual SC800/SC820 2-28 5. Good scanning position. The reading range is from 45 to 260mm distance. 1) Decrease the scanning distance to the bar code when scanning small barcodes. 2) Increase the scanning distance from the bar code when scanning large barcodes 3) The bar code should be located within the green light spots 4) The scanning area is visible by a red illumination area. 6. Bad scanning position. 1) Make sure that the laser beam sweeps across whole barcode. 2) Scanning operations may fail if the illumination beam is positioned as below. 7. Upon reading a bar code, the red LED indicator turns on until the trigger is release or after five seconds. The green LED and the beep tone indicates a good read.
Shin Chuan Computer User’s Manual SC800/SC820 2-29 2.5.9 Installing the SD Card 1. On the PDT attached with a hand-strap, detach and loose the hand-strap. Figure 2-24 Release the Hand strap from PDT 2. Turn the locking latches (right and left) downwards and lift the battery cover away from the PDT. Figure 2-25 Detach the battery cover from PDT
Shin Chuan Computer User’s Manual SC800/SC820 2-30 3. Detach SD Holder and Insert the SD Card into the SD Slot. Figure 2-26 Detach the SD Holder from PDT 2.5.10 Help To tap “?” can get help information for each program. 2.6 Power management 2.6.1 Suspend Mode The PDT will go into a suspend mode when it is idle for a period of time. The idle duration can be customized using the Power control panel (refer to Figure “Schemes Tab”) Suspend mode works and looks just like you have turned the unit off. Press the key to suspend the PDT, Press the key again for the PDT to resume its Previous state. Use the Battery power control panel to set the duration to switch state to Suspend mode when system using battery power. This will save battery power when PDT is not in use. Figure 2-27 Schemes Tab 1 23
Shin Chuan Computer User’s Manual SC800/SC820 2-31 Suspending: The following conditions will suspend: z Press <Power> key while the unit is on. z The duration timer of item “Switch state to Suspend” expires, which indicates that there has been no use for a specified of time. z The battery pack is completely discharged. z Tap Start > Suspend 2.6.2 Resuming Use one of following methods to resume (wake up the PDT): z Press <Power> key to suspend or resume (wake up). When a battery pack completely discharges while the unit is in suspend mode, the PDT remains suspended until discharged battery condition is corrected. 2.7 Resetting the PDT 2.7.1 Software (Warm) Reset A warm reset is a transition from the on, idle, or suspend power state that close all applications, clears the working RAM, but preserves the file system. Reason to Warm Reset: If an application “ hangs ”, initiate a warm reset to terminate the application only. Process to Warm Reset: To a warm reset, press “ Reset ” button. Tap here to let PDT into suspend mode
Shin Chuan Computer User’s Manual SC800/SC820 2-32 After Warm Reset: z The desktop appears with the application shortcuts on the screen. z The custom settings in the registry are persistent. 2.7.2 Cold Reset 1) You can use Cold Reset to initiate device if WINCE.NET OS lock up or Warm Reset still can’t work 2) To perform Cold Reset, press “ Power ” and “ Reset ” button simultaneously. 3) Device will initiate boot up after Cold Reset. CAUTION: Only use the Warm Reset. Try warm reset before you initiate Cold Reset. All applications will be Closed and working RAM and all files will be cleared if you initiate the Cold Reset. It’s better usually to back up your files to Flash ROM, Flash Card or PC.
Shin Chuan Computer User’s Manual SC800/SC820 3-1 Chapter 3. Setting 3.1 Introduction To view available options for PDT’s setting, tap Start > Settings. Then, there are three items inside “Control Panel”, “Network and Dial-up” and “Taskbar and Start”. 3.2 Control Panel To view the Control Panel and settings you can modify by tapping Start > Settings > Control Panel. Figure 3-1 Control Panel 3.2.1 BarCode Setting CAUTION：Please do not enter into any Barcode Application Program before settings completing this Barcode. There are three Tabs for scanner configuration setting: “Basic” Tab, “Bar Code List” Tab and “Code ID” Tab. In addition, there is “BarCode Setup” for the “Code Configure” Tab.
Shin Chuan Computer User’s Manual SC800/SC820 3-2 3.2.1.1 “Basic” Tab Figure 3-2 Basic Tab Table 3-1 Basic Description Field Name Description Select the numbers of beep tone after scan OK. None After scanning the barcode, do not give out beep sound. One Time After scanning the barcode, give out beep one time. Beep After Scan OK Two Times After scanning the barcode, give out beep two times. Scan Timeout (sec) Select the scanning timeout duration (in seconds) from this pull-down list. <2 ~ 20 sec, Default: 5> None After showing barcode, do not action. CRLF After showing the barcode, jump to next row. Space After showing the barcode, jump one unit. Termination Code Tab After showing the barcode, jump a section. Disable Disable this functionality. Continuous Scan 1 ~5 sec Alternate second number of Continuous Scan.
Shin Chuan Computer User’s Manual SC800/SC820 3-3 Field Name Description Select a method based upon the barcode scanning application you will use. Type Writing A unit continues a unit, fast showing barcode number. Copy & Paste Once show barcode number. Keyboard Message Disable Not show the barcode number. Prefix Type the desired label prefix in this text box Suffix Type the desired label suffix in this text box Default Press “Default” button to reset all configuration setting of “Basic” Tab into default values. F/W ver. Decoder firmware version. Set All To Default Press “Set All To Default” button to reset all configuration setting of “Basic” Tab, “Code Configure” Tab, “Code ID” Tab and all barcode of “BarCode Setup” into default values. 3.2.1.2 “Bar Code List” Tab: Select the barcode symbologies you plan to scan from the list. Tap to enable/disable the desired symbologies. Figure 3-3 Bar Code List Tab
Shin Chuan Computer User’s Manual SC800/SC820 3-4 Table 3-2 Bar Code List Description Barcode Symbology Description Type A. Numeric-only Barcodes UPC-E Compressed version of UPC code for use on small products. UPC-A Universal product code seen on almost all retail products in the USA and Canada. EAN-13 / ISBN EAN-13: European Article Numbering international retail product code. ISBN: Special use of the EAN-13 symbol to used internationally to mark books. EAN-8 / JAN-8 Compressed version of EAN code for use on small products. UPC-EAN Add-ON 2/5 UPC-A, UPC-E, EAN-13, and EAN-8 may all include an additional barcode to the right of the main barcode. This second barcode, which is usually not as tall as the primary barcode, is used to encode additional information for newspapers, books, and other periodicals. Industrial 2 of 5 / IATA Older code not in common use. Interleaved 2 of 5 Compact numeric code, widely used in industry, air cargo, other applications. Plessey / MSI Plessey: Older code commonly used for retail shelf marking. MSI: Variation of the Plessey code commonly used in USA. Code 11 Used primarily for labeling telecommunications equipment. Codabar / NW 7 Older code often used in library systems, sometimes in blood bank. Matrix 2 of 5 Used in miscellaneous industrial applications, and mechanical numbering systems. Type B. Alphanumeric Barcodes Code 39 / Code32 General-purpose code in very wide use world-wide. Code 93 Compact code similar to Code 39.
Shin Chuan Computer User’s Manual SC800/SC820 3-5 Code128 / UCC EAN128 Very capable code, excellent density, high reliability; in very wide use world-wide. Widely used data formatting model for Code 128 Type C. Others Barcodes China Post Used by China Postal Service for automated mail sorting. Code 4 --- GTIN Global Trade Identification Number Korea Code 3 of 5 --- RSS Reduced Space Symbology 3.2.1.3 “Code ID” Tab: Figure 3-4 Code ID Tab Table 3-3 Code ID Description Code ID is added into prefix of the barcode and let user identify which kind of barcode being scanned. Enable Code ID Enable this functionality. Set 1 ~ Set 5 Select one default value by Set 1 ~ Set 5. (See the “Table 3-4 Code ID Set1-Set5 Table”)
Shin Chuan Computer User’s Manual SC800/SC820 3-6 User Define Establish number by oneself. Barcode List Set 1 ~ Set 5: defaults setting. User Define: select barcode to define. Default Press “Default” button to reset all configuration setting of “Code ID” Tab into default values. Table 3-4 Code ID Set1-Set5 Table Set 1 Set 2 Set 3 Set 4 Set 5 UPC-E S E C E E UPC-A M A A A E EAN-13 / ISBN M A A F E EAN-8 / JAN-8 P B B F E Industrial 2 of 5 / IATA C H H H S Interleaved 2 of 5 D I Z I S Plessey / MSI V V D P M Code 11 J J J J J Codabar / NW 7 F N X N F Matrix 2 of 5 E G G G S Code 39 / Code 32 A C Y M A Code 93 I L L L G Code 128 H K K K C Code 4 U U U U U Korea Code 3 of 5 R R R R R RSS R R R R R UCC128 / EAN128 W W W W W 3.2.1.4 BarCode Setup A. Select barcode type then select barcode to setting. B. Press “Default” button to reset all configuration setting of this barcode into default values. C. Press “Apply” button to be decided setting of this barcode. Please see 3.2.2 Symbologies List for more detail information of each Barcode.
Shin Chuan Computer User’s Manual SC800/SC820 3-7 Figure 3-5 BarCode Setup 3.2.2 Symbologies List A Type -- Numeric-only Barcodes 3.2.2.1 UPC-E Figure 3-6 UPC-E
Shin Chuan Computer User’s Manual SC800/SC820 3-8 Table 3-5 UPC-E Description Item Description Ignore 1st digit Do not transmit 1st digit by barcode. Format Transmit 1st digit Transmit 1st digit by barcode. Send Check Digit Whether send check digit by barcode. 3.2.2.2 UPC-A UPC-A movements together with EAN-13, so only Enable EAN-13 then UPC-A will be Enable, too. Figure 3-7 UPC-A Table 3-6 UPC-A Description Item Description Ignore 1st & 2nd digits Do not transmit 1st digit by barcode.Transmit 1st digit Transmit 1st digit by barcode. Transmit 2nd digit Transmit 2nd digit by barcode. Format Transmit 1st & 2nd digits Transmit 1st & 2nd digits by barcode.Send Check Digit Whether send check digit by barcode.
Shin Chuan Computer User’s Manual SC800/SC820 3-9 3.2.2.3 EAN-13 / ISBN Figure 3-8 EAN-13 / ISBN Table 3-7 EAN-13 / ISBN Description Item Description Ignore 1st & 2nd digits Do not transmit 1st digit by barcode.Transmit 1st digit Transmit 1st digit by barcode. Transmit 2nd digit Transmit 2nd digit by barcode. Format Transmit 1st & 2nd digits Transmit 1st & 2nd digits by barcode.Send Check Digit Whether send check digit by barcode. Enable ISBN Code Whether use this ISBN Code.
Shin Chuan Computer User’s Manual SC800/SC820 3-10 3.2.2.4 EAN-8/JAN-8 Figure 3-9 EAN-8/JAN-8 Table 3-8 EAN-8/JAN-8 Description Item Description Ignore 1st digit Do not transmit 1st digit by barcode.Format Transmit 1st digit Transmit 1st digit by barcode. Send Check Digit Whether send check digit by barcode. Convert to EAN-13 When this option is selected the scanner will convert EAN-8 to EAN-13 by transmitting five zeroes … Ahead of code Add five zeroes at prefix of the barcode. Add five 0 After 3 digits Add five zeroes after 3rd digits.
Shin Chuan Computer User’s Manual SC800/SC820 3-11 3.2.2.5 UPC-EAN Add on 2/5 A. UPC-E, UPC-A, EAN-13 / ISBN and EAN-8 / JAN-8 may all include an additional barcode to the right of the main barcode. B. This barcode will show primary & additional code together. C. So the UPC-EAN Add-ON 2/5 code is unable to use alone, must operate in UPC-E or UPC-A or EAN-13 / ISBN or EAN-8 / JAN-8. Figure 3-10 UPC-EAN Add on 2/5 Table 3-9 UPC-EAN Add-On 2/5 Description Item Description Only read the code with Addon 2/5 Only reads the codes that have addenda.
Shin Chuan Computer User’s Manual SC800/SC820 3-12 3.2.2.6 Industrial 2 of 5 / IATA Figure 3-11 Industrial 2 of 5 / IATA Table 3-10 Industrial 2 of 5 / IATA Description Item Description Send Check Digit Whether send check digit by barcode. Enable IATA Code Whether use this IATA Code. Checksum Verify Whether verify checksum by barcode. Min Length can be set from 2 to 48 Min-Max (Default: 2 / 48)Max Length can be set from 2 to 48Length 1 can be set from 2 to 48 Length 2 can be set from 2 to 48 Length Fixed Length 3 can be set from 2 to 48
Shin Chuan Computer User’s Manual SC800/SC820 3-13 3.2.2.7 Interleaved 2 of 5 Figure 3-12 Interleaved 2 of 5 Table 3-11 Interleaved 2 of 5 Description Item Description Send Check Digit Whether send check digit by barcode. Checksum Verify Whether verify checksum by barcode. Min Length can be set from 4 to 48 Min / Max (Default: 4 / 48)Max Length can be set from 4 to 48 Length 1 can be set from 4 to 48 Length 2 can be set from 4 to 48 Length Fixed Length 3 can be set from 4 to 48
Shin Chuan Computer User’s Manual SC800/SC820 3-14 3.2.2.8 Plessey / MSI Figure 3-13 Plessey / MSI Table 3-12 Plessey / MSI Description Item Description Mode 10 Mode 10-10 Format Mode 11-10 Checksum mode for this barcode. Send Check Digit Whether send check digit by barcode. 1 Digit Check 1 digit & send by checksum. 2 Digits Check 2 digits & send by checksum.
Shin Chuan Computer User’s Manual SC800/SC820 3-15 3.2.2.9 Code11 Figure 3-14 Code 11 Table 3-13 Code 11 Description Item Description Send Check Digit Whether send check digit by barcode. 1 Digit Check 1 digit & send by checksum. 2 Digits Check 2 digits & send by checksum.
Shin Chuan Computer User’s Manual SC800/SC820 3-16 3.2.2.10 Codabar / NW7 Figure 3-15 Codabar / NW7 Table 3-14 Codabar / NW7 Description Item Description Start / Stop Digit Whether transmit Start & Stop Digit. ABCD abcd TN*E tn*e Start / Stop transmit type Checksum Verify Whether verify checksum by barcode.
Shin Chuan Computer User’s Manual SC800/SC820 3-17 3.2.2.11 Matrix 2 of 5 Figure 3-16 Matrix 2 of 5 Table 3-15 Matrix 2 of 5 Description Item Description Send Check Digit Whether send check digit by barcode. Checksum Verify Whether verify checksum by barcode. Min Length can be set from 4 to 48 Min-Max (Default: 4 / 48)Max Length can be set from 4 to 48 Length 1 can be set from 4 to 48 Length 2 can be set from 4 to 48 Length Fixed Length 3 can be set from 4 to 48
Shin Chuan Computer User’s Manual SC800/SC820 3-18 B Type -- Alphanumeric Barcodes 3.2.2.12 Code39 / Code32 Figure 3-17 Code39 / Code32 Table 3-16 Code39 / Code32 Description Item Description Code39 Standard Enable Code 39 Standard charactersCode39 Full ASCII Enable Code 39 Full ASCII characterFormat Code32 Enable Code 32 Start / Stop Digit Whether transmit Start & Stop Digit.Verify Whether verify checksum by barcode. Checksum Transmit Whether transmit checksum by barcode.
Shin Chuan Computer User’s Manual SC800/SC820 3-19 3.2.2.13 Code93 The barcode does not have setting. Figure 3-18 Code93 3.2.2.14 Code128 / UCC EAN128 Figure 3-19 Code 128 / UCC EAN128 Table 3-17 Code128 / UCC EAN128 Description Item Description Enable UCC128/EAN128 Enable UCC128/EAN128.
Shin Chuan Computer User’s Manual SC800/SC820 3-20 C Type -- Others Barcodes 3.2.2.15 China Post Figure 3-20 China Post Table 3-18 China Post Description Item Description Checksum Verify Whether verify checksum by barcode. Send Check Digit Whether send check digit by barcode. Min Length can be set from 4 to 48 Min-Max (Default: 4 / 48) Max Length can be set from 4 to 48 Length 1 can be set from 4 to 48 Length 2 can be set from 4 to 48 Length Fixed Length 3 can be set from 4 to 48
Shin Chuan Computer User’s Manual SC800/SC820 3-21 3.2.2.16 Code4 The barcode does not have setting. Figure 3-21 Code4 3.2.2.17 GTIN The barcode does not have setting. Figure 3-22 GTIN
Shin Chuan Computer User’s Manual SC800/SC820 3-22 3.2.2.18 Korea Code 3 of 5 The barcode does not have setting. Figure 3-23 Korea Code 3 of 5 3.2.2.19 RSS Figure 3-24 RSS Table 3-19 RSS Description Item Description Convert to UCC128 The scanner will convert RSS to UCC128. Checksum Verify Whether verify checksum by barcode.
Shin Chuan Computer User’s Manual SC800/SC820 3-23 3.2.3 Bluetooth Device Properties Table 3-20 Bluetooth Device Properties ICON ITEM & FUNCTION z “BT Service” Tab: (Figure 3-25) 9 Tap the “Enable Bluetooth Device” to enable Bluetooth device(Figure 3-26). 9 Wait for 20 seconds in order to initialize the Bluetooth hardware correctly. 9 Click “Scan Device Service” to pop “Bluetooth Manager” window. Then tap the Scan Device button to initiate a scan for Bluetooth hardware. The Bluetooth manager lists the Bluetooth devices that it finds, see Figure 3-28. If Bluetooth hardware is not found the Bluetooth Hardware Error window appears, see Figure 3-29. Table 3-21 described the Bluetooth Icons. 9 Double tap the device to connect to on the device list. The Bluetooth Manager Authentication window appears. Tap No to connect to the device without authentication, or tap Yes to authenticate the device before connecting. (Figure 3-30) 9 If the Yes button was selected in the Bluetooth Manager Authentication window, the enter PIN windows appears. Enter a PIN (between 1 and 16 characters) in the Enter PIN: text box, and tap OK. The mobile computer sends the PIN request to the device for bonding. (Figure 3-31) 9 When prompted, the same PIN must be entered on the other device. When the PIN is entered correctly on the other device, the bonded icon appears on the device list. (Figure 3-32) z “Serial Port” Tab: (Figure 3-33) 9 Tap the “Enable Bluetooth Device” to enable Bluetooth device. 9 Wait for 20 seconds in order to initialize the Bluetooth hardware correctly. 9 If want to use Virtual com, only SPP base profiles are supported.(i.e. Printer, Modem, and LAP).Switch to “Serial
Shin Chuan Computer User’s Manual SC800/SC820 3-24 Port” tab, and will see the devices you had trusted or active. Select the device that you want to map a virtual com and which virtual com you want to use. 9 Now COM1 has mapped for BT device. Figure 3-25 Bluetooth Device Properties Figure 3-26 Bluetooth Device Properties 3-27 Bluetooth Manager Windows 3-28 Bluetooth Manager Windows
Shin Chuan Computer User’s Manual SC800/SC820 3-25 Figure 3-29 Bluetooth Error Windows Figure 3-30 Bluetooth Manager Windows Figure 3-31 Bluetooth Enter PIN Windows Figure 3-32 Bluetooth Manager Windows
Shin Chuan Computer User’s Manual SC800/SC820 3-26 Figure 3-33 Bluetooth Manager Windows Figure 3-34 Bluetooth Manager Windows Figure 3-35 Bluetooth Manager Windows Figure 3-36 Bluetooth Manager Windows Note: If the device to which the mobile computer is bonding does not appear in the list, ensure it is turned on, in discoverable mode, and within range (30 feet / 10 meters) of the mobile computer.
Shin Chuan Computer User’s Manual SC800/SC820 3-27 Table 3-21 Bluetooth Icon Icon Description Unknown device icon Device is not defined Locked icon Device is locked and cannot be bonded to. Not locked icon Device is not locked and can be bonded to. Bluetooth device icon Bluetooth device Bonded device icon Bonded Bluetooth device Mobile device icon Device is a mobile device Phone icon Device is a phone. Printer icon Device is a printer Network icon Device is a network. Linked icon Device is linked. 3.2.4 Certificates Certificates are used by some applications for establishing trust and for secure communications. Certificates are signed and issued by certificate authorities and are valid for a prescribed period of time. Windows CE manages multiple certificate stores. Table 3-22 Certificates ICON ITEM & FUNCTION z “Store” Tab: (Figure 3-37) 9 In the Stores tab, select the certificate store you wish to view or modify from the drop-down list (Figure 3-37). 9 The “Trusted Authorities “store lists the top-level certificates for authorities you trust.( Figure 3-38 , Figure 3-39) 9 The “My Certificates “store contains your personal certificates, which you use to identify yourself. 9 Intermediate certificate authorities that help establish a chain of trust are stored in the “Other Authorities” store.
Shin Chuan Computer User’s Manual SC800/SC820 3-28 z “Store” Tab: (Figure 3-39) 9 To add a certificate or associated private key to the selected store, select “Import” (Figure 3-39). 9 To view more details of the selected certificate, such as the expanded name or expiration date, choose “View”. 9 To delete the selected certificate from the store, choose “Remove”. Figure 3-37 Certificates Figure 3-38 Certificates Figure 3-39 Certificates Figure 3-40 Certificates
Shin Chuan Computer User’s Manual SC800/SC820 3-29 Figure 3-41 Certificates 3.2.5 Control Center The Control Center includes four AP, listed the following.. Figure 3-42 Control Center
Shin Chuan Computer User’s Manual SC800/SC820 3-30 3.2.5.1 Information Table 3-23 Information ICON ITEM & FUNCTION z “Information” Tab: 9 Provide Software version, MAC address, Bluetooth ID, Serial No. and Configuration No. 3.2.5.2 Brightness Table 3-24 Brightness ICON ITEM & FUNCTION LCD Brightness: (Figure 3-43) Set the LCD brightness by adjusting the slider from low to highAmounts 5 steps: Every step have corresponding picture of self. 0. 1. 2. 3. 4. 5. The table must disable when its item is not marked. Battery Power, and device is idle for more than The table has 10 seconds, 30 seconds, 1 minute, 2 minutes, 3 minutes, 4 minutes and 5 minutes. The table must disable when its item is not marked. External Power, and device is idle for more than The table has 1 minute, 2 minutes, 3 minutes, 4 minutes, 5 minutes, 6 minutes, 7 minutes, 8 minutes, 9 minutes and 10 minutes. Enable Keypad Brightness Enable keypad brightness or not.
Shin Chuan Computer User’s Manual SC800/SC820 3-31 Figure 3-43 Brightness 3.2.5.3 Fn-key Settings Table 3-25 Fn-Key ICON ITEM & FUNCTION z Fn-Key Setting: (Figure 3-44) Fn Key The Application Program of default setting F1 Internet Explorer F2 Microsoft WordPad F3 Inbox F4 Windows Explorer 9 To assign your favorite application program to Hot Keys. 9 Choose one of Hot Keys from pull-down list.(Figure 3-44) 9 To tap “Browse…” inside “Assign program” applet. 9 Select one application program you want from program list, then, choose “OK”. (Figure 3-45) 9 To tap “Default” to return back to default setting. (Figure 3-44)
Shin Chuan Computer User’s Manual SC800/SC820 3-32 Figure 3-44 Fn-Key Settings Figure 3-45 Fn-Key Settings 3.2.5.4 Backup Restore Table 3-26 Backup Restore ICON ITEM & FUNCTION 1. You can backup/restore system to/from flash disk or inserted memory card. (Disk on Chip, or SD Card) (Figure 3-46) 2. When you launch this AP, it must check backup file in DOC first. And if you select other storage, it will check again. 3. Then if it has the file, appeared its date behind “Last backup date:”; if not, disable “Restore Now” Button. 4. When you press the Backup/Restore Button will be a warning dialog pop up. (Figure 3-47) 5. When system backup/restoring finished will be a message dialog will pop up. (Backup: Figure 3-48 Restore: Figure 3-49
Shin Chuan Computer User’s Manual SC800/SC820 3-33 Figure 3-46 Backup Restore Figure 3-47 Backup & Restore Start Figure 3-48 Backup OK Figure 3-49 Restore OK
Shin Chuan Computer User’s Manual SC800/SC820 3-34 3.2.6 Date/Time Table 3-27 Date/Time ICON ITEM & FUNCTION z “Date/Time” Tab: (Figure 2-14) 9 Please see the detail information of 2.5.1 Setting Time and Date on P.2-21 3.2.7 Dialing Properties Table 3-28 Dialing properties ICON ITEM & FUNCTION z “Dialing Properties” Tab: (Figure 3-50) 9 In the When dialing from list, select the “Location” where you want to change settings.(Figure 3-50) 9 To create a new location, select “New”. Enter the name of the location, and then select “OK”.(Figure 3-51) 9 Enter or edit the area code and local country code as needed. 9 In Dial using, select “Tone dialing” or “Pulse dialing”. Most phone lines are tone. 9 To automatically disable call waiting, select “□ Disable call waiting by dialing”, select the appropriate number sequence in the list, or enter a new sequence. z Editing dialing patterns: (Figure 3-53) 9 Using the codes listed in the topic; revise the dialing patterns as needed. Notes:  If you need to use character other than the ones listed here, use manual dialing.  Hyphens and spaces in dialing strings are ignored.  Some modems may not respond to the following characters, even though your device lets you add them to the dial string.
Shin Chuan Computer User’s Manual SC800/SC820 3-35 Figure 3-50 Dialing Properties Figure 3-51 Dialing Properties Figure 3-52 Dialing Properties Figure 3-53 Dialing Properties
Shin Chuan Computer User’s Manual SC800/SC820 3-36 3.2.8 Display Properties Table 3-29 Display properties ICON ITEM & FUNCTION z “Background” Tab: (Figure 3-54) 9 From the “Image” list, select an image you want as the background of the desktop.(Figure 3-55) 9 To locate an image in another folder, select “Browse”.(Figure 3-56) 9 To have the image cover the entire background, select “ □ Tile image on background ” z “Appearance” Tab: (Figure 3-57) 9 Change the color scheme:( Figure 3-58) ¾ From the” Scheme” list, select a scheme. ¾ View your choice in the preview box. If you like the scheme, select “Apply”. 9 Create a custom color scheme: ¾ From the “Item” list, select a display item. ¾ From the “Basic colors” list, select a color, and select “OK”. ¾ View your color selection(s) in the Preview box. ¾ To save the scheme, select “Save”. ¾ In the “Save this color scheme as” box, enter a name for the scheme, and select “OK”. ¾ Select “Apply”.
Shin Chuan Computer User’s Manual SC800/SC820 3-37 Figure 3-54 Display properties Figure 3-55 Display properties Figure 3-56 Display properties Figure 3-57 Display properties
Shin Chuan Computer User’s Manual SC800/SC820 3-38 Figure 3-58 Display properties 3.2.9 Input Panel Table 3-30 Display properties ICON ITEM & FUNCTION z “Input panel” Tab: (Figure 3-59) 9 Select the input method you want to change. 9 To change the Soft Keyboard Options , tap “Option” (Figure 3-60) z “Options” Tab: (Figure 3-60) 9 Change the soft keyboard options as desired, selecting from: ¾ Large or small keys ¾ Using gestures for space, black-space shift, and enter. 9 To exit the soft keyboard Options, press “OK” on the control bar, or press the <Enter> key on the keypad. 9 To exit the Input Panel, press “OK” on the control bar, or press the <Enter> key on the keypad.
Shin Chuan Computer User’s Manual SC800/SC820 3-39 Figure 3-59 Input Panel Properties Figure 3-60 Input Panel Properties 3.2.10 Internet Options Table 3-31 Internet Options ICON ITEM & FUNCTION z “General” Tab: (Figure 3-61) 9 Type in the URL of desired start page and the desired search engine. You also change the Cache Size, clear the Cache and Clear the History.. z “Connection” Tab: (Figure 3-62) 9 Modify the network access setting as desired. z “Security” Tab: (Figure 3-63) 9 Modify the security settings as desired. You can enable any of the following by tapping the checkbox: z “Advanced” Tab: (Figure 3-64) 9 Modify the security settings as desired. You can enable any of the following by tapping the checkbox: ¾ Display Image in pages ¾ Play sounds in pages ¾ Enable scripting ¾ Display a notification about every script error ¾ Underline links-
Shin Chuan Computer User’s Manual SC800/SC820 3-40 ○ Never ○ Always ○ Hover Figure 3-61 Internet Settings Figure 3-62 Internet Settings Figure 3-63 Internet Settings Figure 3-64 Internet Settings
Shin Chuan Computer User’s Manual SC800/SC820 3-41 3.2.11 Keyboard Table 3-32 Keyboard ICON ITEM & FUNCTION z “Repeat” Tab: (Figure 3-65) 9 To change the amount of time between depressions before repetition starts, adjust the Repeat delay slider 9 To change the repeat rate, adjust the Repeat rate slider. 9 Test your new setting. 9 Tap “ OK” to exit the “Keyboard” Tab. Figure 3-65 Keyboard Properties
Shin Chuan Computer User’s Manual SC800/SC820 3-42 3.2.12 Network and Dial-up Connections Table 3-33 Network and Dial-up Connections ICON ITEM & FUNCTION z “Connection” Tab: (Figure 3-66) 9 To create a “Dial-up Connection”: ¾ Double-tap the “Make New connection”. ¾ In the “Make New Connection” dialog box, enter a name for the connection.(Figure 3-67) ¾ Select “Dial-Up Connection”. ¾ Select the “Next” button. ¾ Select the modem you want use. ¾ Select “Configure” (Figure 3-68) ¾ Under “Connection Reference”, use the default settings provided. If you can’t connect using these settings, see your ISP or network administrator for specific information. If you want to always enter a phone number before connecting, Select “Manual Dial”. Select “OK”. ¾ Select “TCP/IP Settings”.(Figure 3-72) in the “General” tab. ensure “Use Server-assigned IP address” is selected. In the “Name Servers” tab, ensure “Use Server-assigned addresses” is selected, and select “OK”. If you are unable to connect with these default settings, see your ISP or network administrator for specific TCP/IP information. ¾ Select the “Next” button and type the telephone number.¾ Select the “Finish” button. The connection you just created appears as an icon in the “Network and Dial-up Connections” folder. 9 Set up a point-to-Point Protocol(PPP) account with an ISP and obtain the following information: ¾ Access telephone number ¾ User name ¾ Password Once you have established an account, create a new connection on your device. When creating this connection, you should be able to use all of the default TCP/IP settings provided
Shin Chuan Computer User’s Manual SC800/SC820 3-43 in the Make New Connection Wizard. If you can’t connect using the default settings, contact your ISP or access your ISP’s Web site for specific TCP/IP information as well as primary and secondary DNS address. 9 Modify connection setting ¾ Select Start > Settings > Network and Dialup Connections ¾ Select the icon for connection settings you want to modify. ¾ Select File > Properties, or double- tap the appropriate icon. ¾ Select desired options. There may be additional settings that depend on the connection. To modify, select the icon and select the icon and select Advanced Settings… from the menu. Figure 3-66 Network and Dial-up Connections Figure 3-67 Network and Dial-up Connections
Shin Chuan Computer User’s Manual SC800/SC820 3-44 Figure 3-68 Network and Dial-up Connections Figure 3-69 Network and Dial-up Connections Figure 3-70 Network and Dial-up Connections Figure 3-71 Network and Dial-up Connections
Shin Chuan Computer User’s Manual SC800/SC820 3-45 Figure 3-72 Network and Dial-up Connections Figure 3-73 Network and Dial-up Connections Figure 3-74 Network and Dial-up Connections Figure 3-75 Network and Dial-up Connections
Shin Chuan Computer User’s Manual SC800/SC820 3-46 Figure 3-76 Network and Dial-up Connections Figure 3-77 Network and Dial-up Connections 3.2.13 Owner Table 3-34 Owner ICON ITEM & FUNCTION z “Identification” Tab: (Figure 3-78) 9 Fill in or edit the data as desired. 9 To have this information displayed when you start your device, select “Display Owner Identification” at Power On. 9 To set up identification for remote networks, see Setting up identification for remote networks. z “Notes” Tab: (Figure 3-79) 9 Enter the Notes you use to the Display Owner notes z “Network ID” Tab: (Figure 3-80) 9 Enter the user name, password, and domain name you use to log on to remote network.
Shin Chuan Computer User’s Manual SC800/SC820 3-47 Figure 3-78 Owner Properties Figure 3-79 Owner Properties Figure 3-80 Owner Properties
Shin Chuan Computer User’s Manual SC800/SC820 3-48 3.2.14 Password Table 3-35 Password ICON ITEM & FUNCTION z “Password Setting” Tab: (Figure 3-81) 9 Enter the password 9 In the “Confirm password “box, enter the password again.9 To require the password on startup, select “Enable password protection at power- on“. and/or select “Enable password protection for screen saver” 9 To exit the Password control panel, press “OK” from the control bar, or press the <Enter> key on the keypad. Figure 3-81 Password Properties 3.2.15 PC Connection Table 3-36 PC Connection ICON ITEM & FUNCTION z “PC Connection” Tab: (Figure 3-82) 9 Select the first checkbox to enable direct connections to the desktop computer. (Figure 3-81)
Shin Chuan Computer User’s Manual SC800/SC820 3-49 9 Tap the “Change Connection…” button to modify the connection method from USB or Serial. (Figure 3-83) 9 To exit the “Change Connection” dialog, press “OK” from the control bar, or press the <Enter> key on the keypad. 9 To exit the “PC Connection” properties control panel, press “OK” from the control bar, or press the <Enter> key on the keypad. Figure 3-82 PC Connection Figure 3-83 PC Connection 3.2.16 Power Table 3-37 Power ICON ITEM & FUNCTION z “Battery” Tab: (Figure 3-84) 9 Provide change level indicators for Main battery and Backup battery. 9 Provide remaining power capacity of main battery. 9 If a “Main Batteries very Low” warning message shows, the remaining battery life is around 30 minutes to SC800 shuts down. ( Figure 3-88) 9 The PDT will shutdown during the main batteries capacity
Shin Chuan Computer User’s Manual SC800/SC820 3-50 is around 0% 9 To exit Battery control panel, press “OK” from the command bar, or press <Enter> key on keypad. z “Schemes” Tab: (Figure 3-85) 9 The Scheme Tab allows you to determine the time to switch state to Suspend mode when using either Battery Power or AC Power. 9 Select Battery Power or AC Power as the power scheme from the pull-down list.( Figure 3-86) 9 Select the time to suspend mode from the pull-down list. ( Figure 3-79) z “Device Status” Tab: ( Figure 3-87) Provide power level of device – The power level ranges from “ High(D0)” which means the device is at the highest power level to “Off(D4)” which means the device is at the lowest power level. Note: This ICON inside the Task Bar shows that AC adapter provides power to the PDT The ICON inside the Task Bar shows that Main Batteries provides the power to the PDT. The ICON inside the Task Bar shows that AC adapter provides the power to the PDT and is charging the main batteries.. Figure 3-84 Power Figure 3-85 Power
Shin Chuan Computer User’s Manual SC800/SC820 3-51 Figure 3-86 Power Figure 3-87 Power Figure 3-88 Power
Shin Chuan Computer User’s Manual SC800/SC820 3-52 3.2.17 Regional Settings Table 3-38 Regional Settings ICON ITEM & FUNCTION z “Region” Tab: (Figure 3-89) 9 Select the desired location/language. 9 Review the Appearance samples in the bottom half of the screen. 9 Select the Tab at the top for any settings you wish to change, Options to modify include Number, Currency, Time, and Date. Figure 3-89 Regional Settings 3.2.18 Remove Programs Table 3-39 Remove Programs ICON ITEM & FUNCTION z “Remove Programs” Tab: (Figure 3-90) 9 Only user installed programs can be removed. ¾ Select the program you wish to remove from the list and press “remove” button.
Shin Chuan Computer User’s Manual SC800/SC820 3-53 Figure 3-90 Regional Settings 3.2.19 Storage Manager Table 3-40 Storage Manager ICON ITEM & FUNCTION z “Storage Manager” Tab: (Figure 3-91) 9 To change Storage properties control panel default settings: Insert. Compact Flash(CF) or Secure digital (SD) storage card into the unit. ¾ Select Start > Settings > Control Panel > Storage Properties ¾ From the “Storage Info” pull-down list, select the desired storage device. ¾ You can also format, dismount, and create partitions on storage devices using this control panel. ¾ To save and exit the Storage Properties control panel, press “OK” from the control bar, or press the <Enter> key on the keypad. Caution: Dismounting or formatting the DiskOnChip will erase all files and program stored in Flash Memory
Shin Chuan Computer User’s Manual SC800/SC820 3-54 Figure 3-91 Storage Manager 3.2.20 Stylus Table 3-41 Stylus ICON ITEM & FUNCTION z “Double-Tap” Tab: (Figure 3-92, Figure 3-93) 9 Double-tap the checkerboard grip at a comfortable speed. 9 Double-tap clapboard to test your settings 9 The function is OK if the figures are changed from Figure 3-84 to Figure 3-85. 9 To tap “OK” to exit the Stylus Properties. z “Calibration”: (Figure 3-94, Figure 3-95) 9 In the Welcome Wizard, you tapped a target with the stylus to set the amount of pressure needed for the screen to respond to your stylus taps. 9 Please also see 2.4.3 Calibration of the touch Screen
Shin Chuan Computer User’s Manual SC800/SC820 3-55 Figure 3-92 Stylus Properties Figure 3-93 Stylus Properties Figure 3-94 Stylus Properties Figure 3-95 Stylus Properties
Shin Chuan Computer User’s Manual SC800/SC820 3-56 3.2.21 System Table 3-42 System ICON ITEM & FUNCTION z “General” Tab: (Figure 3-96) 9 To show: ¾ Firmware information ¾ Information about Processor type, Memory size, Expansion card z “Memory”: (Figure 3-97) 9 Move the slider to adjust memory allocation. Default storage memory is normally is normally set to about 8MB with the reminder assigned to Program memory. 9 Press the “OK” key on the Keypad. Note: the difference is occupied by OS between the RAM size in Information properties and total memory size of storage memory and program memory z “Device Name” Tab: (Figure 3-98) 9 Your device uses this information to identify itself to other computers. 9 The input panel will open to facilitate data entry. 9 To close the Device Name, press the “OK” button, or press the <Enter> key on keypad. z “Copyrights” Tab: (Figure3-99) 9 Refer to this tab for specific copyright data. As a user, you are responsible to read this statement.
Shin Chuan Computer User’s Manual SC800/SC820 3-57 Figure 3-96 System Properties Figure 3-97 System Properties Figure 3-98 System Properties Figure 3-99 System Properties
Shin Chuan Computer User’s Manual SC800/SC820 3-58 3.2.22 Terminal Server Client Licenses Table 3-43 Terminal Server Client Licenses ICON ITEM & FUNCTION z “Terminal Server Client Licenses” Tab: (Figure 3-100) 9 The section allow users can connect to Terminal Server, If the user has License. Figure 3-100 Terminal Server Client Licenses 3.2.23 Volume & Sounds Properties Table 3-44 Volume & Sound ICON ITEM & FUNCTION z “Volume” Tab: (Figure 3-101) 9 The factory default for Volume is the forth level. You can adjust the volume to your environment and comfort. ¾ Set the volume by adjusting the slider from Soft to Loud, or press Right or Left edge of Navigation keysz “Sounds ” Tab: (Figure3-102) 9 Enable the desired sounds for key clicks, screen taps, notifications, and applications.
Shin Chuan Computer User’s Manual SC800/SC820 3-59 Figure 3-101 Volume & Sound Figure 3-102 Volume & Sound 3.3 Taskbar and Start Menu Table 3-45 Taskbar and Start menu ICON ITEM & FUNCTION z “General” Tab: (Figure 3-104) 9 In this tab, You can change the position of the Taskbar and Start menu ¾ Is always on top or not ¾ Auto hide or not ¾ Show Clock or not z “Advanced ” Tab: (Figure 3-105) Taskbar and Start Menu 9 Tap the “Clear” button to remove the contents of the Documents Menu. 9 Enable “□ Expand Control Panel” to list all icons of Control Panel from top to bottom.
Shin Chuan Computer User’s Manual SC800/SC820 3-60 Figure 3-103 Taskbar and Start Menu Figure 3-104 Taskbar and Start Menu- General Figure 3-105 Taskbar and Start Menu- Advanced
Shin Chuan Computer User’s Manual SC800/SC820 4-1 Chapter 4. Communication 4.1 Installing & Setting Up Microsoft ActiveSync 4.1.1 Installing Microsoft ActiveSync on the Host PC Microsoft ActiveSync is a file transfer tool to synchronize the files on a PC with the files on your PDT. To install Microsoft ActiveSync, complete the following steps on the PC: 1. Go to the Microsoft Windows CE.NET website and download the latest current version of ActiveSync: http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-synch.mspx 2. Install the latest version of Microsoft ActiveSync on the host PC. 3. Open ActiveSync. 4. Select File > Communication Settings from ActiveSync’s menu bar. 5. Go to “Using ActiveSync” on page 4-1 to continue using ActiveSync. 4.1.2 Connecting PDT to Host PC 1. You can use either the USB/Serial (RS232) port of Single Dock or a USB/Serial (RS232) cable to connect the PDT to the Host PC. ․To use the dock, you must first insert the PDT into the slot, making sure that the unit is firmly seated the dock. ․To use the cable, connect the USB/Serial cable to the PDT. 2. Connect the USB/Serial dock or cable to the Host PC’s serial port or USB port. 3. Connect the dock or PDT to the power adapter and power source. 4.2 Using ActiveSync Use ActiveSync to transfer and synchronize files between the PDT and the Host PC. 4.2.1 Setting up a Partnership During the Microsoft ActiveSync installation, you were prompted to create a partnership with your mobile device. When you set up a partnership, you select synchronization and file conversation settings, which are contained in a file on
Shin Chuan Computer User’s Manual SC800/SC820 4-2 your desktop computer. This file enables your desktop computer to recognize your device. Only devices that have a partnership with a desktop computer can synchronize information between the two computers. For more information on partnerships, please refer to your Microsoft ActiveSync documentation or help file. Transferring Files: To transfer files, complete the following steps on the host PC: 9 Select Start> Programs >Communication > (Serial, or USB) Activesync. 9 Double-click on the selected ActiveSync icon 9 After you have established a connection with PDT, tap the “Explore” button at the top of the ActiveSync window (or select Explore from the File menu). 9 Navigate to the target directory on your PDT and copy the desired file by using the Copy/paste method or dragging and dropping the desired file(s) into the folder. Figure 4-1 Communication
Shin Chuan Computer User’s Manual SC800/SC820 4-3 4.2.2 ActiveSync File Synchronization ActiveSync files synchronization requires an ActiveSync partnership between the PDT and the Host PC. Refer to “Setting up a Partnership”, above: 9 Select the files in the synchronization configuration for the PDT partnership. 9 Select Tools > Options from the ActiveSync command bar to configure the synchronization options. 9 Place the file to be synchronized in the Synchronization folder created you’re My Documents directory. Defaults to the desktop. During the ActiveSync connection, all files in the Synchronization folder will be synchronized to the \My Documents directory on the PDT. Figure 4-2 Connected 4.3 Networking Please see the 3.2.13 Owner, Table 3-34 Owner on page 3-45 for setting up the network ID. And see the 2.5.6 Setting Up Wireless LAN RF to setup the 802.11b/g Wireless LAN for RF connecting.
Shin Chuan Computer User’s Manual SC800/SC820 5-1 Chapter 5. Software Applications 5.1 Introduction The PDT includes Inbox, MediaPlayer,….. You can switch to any software program by tapping the Start Menu. 5.2 Software Applications 5.2.1 Inbox Use Inbox to send and receive e-mail messages in the following ways: 9 Synchronize e-mail messages with Microsoft Exchange or Outlook on the Host Computer. 9 Send and receive e-mail messages by connecting directly to an e-mail server through an Internet server provider (ISP) or a network. To setup “Inbox”: 9 Select Start> Programs> Inbox to open it. 9 Select Service> Options from the command bar. Drag the dialog to show the right edge to configure e-mail. 9 Select “Add…” (Note 1) 9 In the “Service Type” list, select POP3 Mail or IMAP4 Mail. (POP3 is the most common mail protocol for ISPs).Enter a unique name for e-mail service in the “Service name” field. This name cannot be changed later. 9 Select “OK”. 9 The Mail Service Setup wizard appears after you add a service. If you are adjusting the setting of an existing service, select Service> Options, select the service you are using, and then Properties. In the Service Definition dialog box, complete the following entries as needed: ¾ Connection: Select the name of the connection you created to connect to the mail server. If you are receiving e-mail through a network(Ethernet) connection, select Network Connection. If you want Inbox to use your current connection, select (none). If you have not created a connection, select Create new connection. Double-tap the “Make new Connection” icon, and follow the
Shin Chuan Computer User’s Manual SC800/SC820 5-2 instructions in wizard. When finished, select Inbox in the Taskbar and continue setting up Inbox. ¾ POP3 Host(POP3 only): Enter the name of the mail server you use to receive and send messages. ¾ Server(IMPA4 only): Enter the name of he mail server you use to receive and send messages. ¾ User ID: Enter the user name or mailbox ID assigned to you. ¾ Password: Enter the password you use to access this mail account. If you do not want to be prompted to enter the password each time you connect, select “Save password”. ¾ Domain(Windows NT): Enter your Windows NT domain name. This name is required only when connecting to networks, such as a corporate network, that use Windows NT domain security. This is not required for most ISP accounts. If you have trouble connecting, try clearing this box. ¾ SMTP Host: If your mail service uses a separate server for SMTP, enter the name in the box. If you’re setting up a POP3 Mail service with an ISP, the ISP must use an SMTP mail gateway. ¾ Return Address: By default, the return address is set to username@POP3host or username@Servername. Depending on the service you are using. If this is not your e-mail address, enter the correct address in the box. 9 Set general preferences: If you are adjusting the setting of an existing service, select Service> Options, select the service you are using, select Properties, and then select Next. In the General Preferences dialog box, choose any of the following setting settings, all of which are optional: ¾ Disconnect service after actions are performed: Select to automatically disconnect from the server upon completion of all pending actions. This option minimizes connect time and cost. ¾ Check for new messages every: select the time interval(in minutes) at which you want the device to check for new mail. If this option is turned off, you must check for new mail manually by selecting Services> Send/Receive Mail. ¾ Display a message box when new mail arrives (POP3 only): Select to be informed that new mail has arrived.
Shin Chuan Computer User’s Manual SC800/SC820 5-3 ¾ Display a message box when new mail arrives (IMAP4 only): Select to be informed that new mail has arrived. ¾ Send using MIME format (POP3 only): Select to send messages with extended characters. ¾ Only display messages from last 3 days: Select how many day’s messages you want downloaded. 9 Set inbox preferences If you are adjusting the settings of an existing service, select Services> Options, select the service you are using, select Properties, and then select New twice. In the Inbox Preferences dialog box, choose any of the following options: ¾ Get message headers only: Select to save storage space and time by downloading only headers. You can download a full copy of the message later by selecting the message and then Services> Get Full Copy. ¾ Include <number> lines: Select to set the message length (approximate number of lines) that you want to download. ¾ Get Full Copy of messages: Select to receive a full copy of all messages. In addition to the message body, any options you select in When getting full copy will be downloaded. Selecting this option increases the amount of time needed to download messages. ¾ Only synchronize folder hierarchy under Inbox (IMAP4 only): Select to speed download time by preventing the complete downloaded of the folder list every time you connect. ¾ Get meeting requests (POP3 only): Select to download and store copies of meeting requests when getting full copies of messages. This setting applies whether you have chosen to download full copies of messages by default, or you selectively download full copies of messages by opening the message and selecting Services> Get Full Copy Limitations apply. ¾ Get file attachments (POP3 only): Select to download and save message attachments when getting full copies of messages. This option may use significant RAM and slow download time. This setting applies whether you have chosen to download full copies of messages by default, or if you selectively download full copies of
Shin Chuan Computer User’s Manual SC800/SC820 5-4 messages and selecting Services> Get Full Copy. ¾ Get file attachments and meeting requests (IMAP4 only): Select to download and store meeting requests and message attachments when getting full copies of messages. This setting applies you have chosen to download full copies of messages by default, or if you selectively download full copies of messages by opening the message and selecting Services> Get Full Copy Limitations apply. ¾ Only if small than (IMAP4 only): Select to restrict the size of the attachments you download. Set to 10K if you want to receive meeting requests only. 9 Include the original message in a reply: ¾ Select Services> Options> Compose tab. ¾ Under Reply, select Include Body. This setting will place a copy of the original message beneath your response text. ¾ To indent the original message, select Indent. ¾ To add leading characters (such as>) to the original message lines, select Add leading character, and enter the character you want. 9 Save copies of sent messages: By default, sent messages are not saved on your device. ¾ Select Services> Options> Compose tab. ¾ Select Keep copy of sent mail in Sent folder. 9 Set the action to follow deleting, moving, or responding to a message: ¾ Select Services> Options > Read tab. ¾ Select desired options. 9 Delete a message: Select the message and select File> Delete. Messages are moved to Deleted (local) folder and deleted according to the option you have selected in Services> Options> Delete tab: ¾ On connect/disconnect: Deletes messages when you connect or disconnect from your mail service or exit Inbox. ¾ Immediately: Deletes messages as soon as you select File> Delete. ¾ Manual: Deletes messages when you select File> Empty Deleted (local)
Shin Chuan Computer User’s Manual SC800/SC820 5-5 Note: If you are working offline, messages that have been deleted from the device the next time you connect. 9 Empty the Deleted (local) folder: ¾ Select File> Empty Deleted (local). This permanently deletes messages in the Deleted (local) folder. ¾ To check or adjust the current settings for deleting messages, select Services> Options> Delete tab. 9 Move or copy a message: Caution: When you move a message that you have received through POP3 or synchronization to a folder you created on your device, the copy of the message on the server is deleted. This prevents duplicate copies of messages. Although the complete message is moved, message attachments will be deleted if you have not selected the option to download attachments. Once the message is moved, you will be able to access the message only from your device. ¾ Select the message ¾ Select File> Move To or File> Copy To. ¾ Select the destination folder. If you are working offline, the message will be moved or copied from the server the next time you connect. 9 Folder-  Create a folder: ¾ Select File> Folder> New Folder ¾ Type a name for the folder.  Delete a folder: ¾ Select the folder you want to delete ¾ Select File> Delete  Designate a folder as offline: Only IMAP4 folders can be designated as offline. All IMAP4 default folders, such as Inbox, are automatically designated as offline. Messages in offline folders can be viewed when you are disconnected from your mail server. If a folder is not designated as offline, you will be
Shin Chuan Computer User’s Manual SC800/SC820 5-6 able to read and respond to messages in that folder only when connected to the server. ¾ To designate a folder as offline, select the folder and then select Service > Offline Folder.  Rename a folder: ¾ Select the folder you want to rename. ¾ Select File> Folder> Rename Folder. ¾ Type the new name for the folder. Notes: z Default folders, such as Inbox, can’t be renamed. z Folders you create for IMAP4 mail servers can’t be renamed.  Synchronize folders while connected: When you synchronize folders, the contents of your device folders and mail server folders are compared and updated. New mail messages are downloaded, and messages in your device Outbox folder are sent. The synchronization behavior depends on how you connect to your mail server. ¾ When you connect to a POP3 server, the Inbox and Outbox folders on your device are synchronized with the corresponding folders on the mail server. To synchronize after the initial connection, select Services> Send/Receive Mail. ¾ When you connect to an IMAP4 server, Inbox, Outbox, and all folders marked as offline are synchronized. To synchronize all folders after the initial connection, select Services> Synchronize Folders. To synchronize just the selected folder and the Outbox folder, select Services> Send/Receive Mail. 9 Compose and send a message: ¾ In list view, select Compose> New Message ¾ Enter the address of one or more recipients, separating them with a semicolon. If the recipient is listed in the Address Book, enter a few letters of the recipient’s name and select Compose> Check Name. If there is only one match, the e-mail address is inserted. If there is more than one match, select the correct address from the Choose E-mail Recipients dialog box. If there is no match then add a new
Shin Chuan Computer User’s Manual SC800/SC820 5-7 e-mail address through Choose E-mail Recipients. ¾ To attach a file, select File> attachments> Add Attachment. ¾ Select File> Send. If you are working offline, the message is moved to the Outbox folder and will be sent the next time you connect. Tip: to see more header information, select the triangle in the lower-right corner of the header area. Select the triangle again to collapse the header area. 9 Save a message: ¾ Select File> Save to save the message you are composing or editing. The message is not sent and is saved in the inbox folder of the active service. 9 Reply to or forward a message: ¾ Open the message, and then select Compose> Reply to Sender, Reply to All, or Forward. ¾ Enter your response. ¾ Select File> Send. Tips: z Selections in the Options dialog box determine whether the original text is included. z To see more header information, select the inverted triangle in the lower-right corner of the header area. Select the triangle again to collapse the header area. 9 Check Inbox status: ¾ In list view, select Compose> Status. You can view details such as the number of messages to be sent, deleted, and copied, and the number of attachments to be downloaded. 9 Download message from the server: When you download messages, you need to create two connections: a remote connection and a mail server connection. The remote connection connects you and your ISP or network. The mail server connection downloads messages from your mail server to Inbox on your device. When you select Services> Connect in Inbox, Inbox starts a remote connection using the connection you specified when setting up the current
Shin Chuan Computer User’s Manual SC800/SC820 5-8 mail service. If you are already connected through a remote connection other than the one you specified in the service, you will be asked if you want to use the current connection. If you choose not to, you will need to disconnect from the current connection before you can check for new messages. ¾ Select the Services menu and make sure that the service you want to use is selected (the selected service has a bullet next to it.) ¾ Select Services> Connect. The messages on your device and mail server are synchronized: new messages are downloaded to the device Inbox folder, messages in the device Outbox folder are sent, and messages that have been deleted on the server are removed from the device Inbox. Double-tap a message list to open it. ¾ If you read a message and decide that you need the full copy, select File> Get Full Copy while in the message window or Services> Get Full Copy while in list view. This will also download message attachments and meeting requests if you have those options selected in the Inbox Preferences dialog box. You can also choose to download full copies of messages by default. ¾ When finished, select Services> Connect to disconnect. You also need to disconnect your dial-up connection by double-tapping the icon in the status bar and selecting Disconnect. Notes: z Receiving entire messages consumes storage memory. z The size column in the Inbox list view displays the local size and server size of a message. Even when a message has been downloaded fully, these numbers may differ because the size of a message can very between the server and the device. z When using IMAP4 to get Outlook + data, you will see the contents of your Journal folder. File editing transactions and documents (such as Task items, e-mail message, and Word documents) attached using drag and drop will appear as shortcuts on the device. A copy of the document will not be moved to your device, and the shortcut on the device cannot be used to access the documents associated with a journal entry to the device, attach the document to the entry rather than dragging and
Shin Chuan Computer User’s Manual SC800/SC820 5-9 dropping it. Also, be sure to set your IMAP4 service to receive full copies of messages, attachments, and meeting requests. For more information on using Journal, see the Help for the desktop version of Outlook. 9 Working with Message Attachments: ¾ If you receive messages through a remote mail server, in Inbox on the device, select the Get file attachments and meeting requests (IMAP4) or Get meeting requests (POP3) setting in the Inbox Preferences dialog box. For more information, see Set Inbox preferences. Notes: z Embedded images and OLE objects cannot be received as attachments z Embedded messages can be viewed as an attachment when using IMAP4 to receive e-mail. However, this features does not work if TNEF is enabled so that you can receive meeting requests. 9 Check attachments status: ¾ An attachment sent with an e-mail message, whether it has been downloaded or not, will appear as an icon at the bottom of the message in its own window pane. If you don’t see this pane, select File> Attachments> Show Attachments. If TNEF is turned on so you can receive meeting requests, you will not see attachments until they are fully downloaded. ¾ To mark an attachment for downloading in a POP3 or IMAP4 service, double-click it. The attachment will be downloaded the next time you connect. You can also set Inbox to download attachments automatically when you get a full copy of a message. For more information, see Receive attachments. 9 Open an attachment: ¾ With the message open, double-tap the attachment’s icon at the bottom of the message. If you don’t see this pane, select File> Attachments> Show Attachments. 9 Store an attachment: ¾ Select Service> Options> Storage tab. ¾ Select to store attachments on internal RAM or a storage card.
Shin Chuan Computer User’s Manual SC800/SC820 5-10 ¾ If you use more than one storage card, select it from the list. Note: Once you make the above selection, all attachments will be moved to the selected card. 9 Delete an attachment: ¾ To delete an attachment from a message you are sending, select the attachment, and then select Edit> Clear or press the DEL key on the keypad. ¾ To delete an attachment you have received, delete the message. 9 Attach a file to a message: ¾ With the message open, select File> Attachments> Add Attachment. ¾ Select the file you want to attach. Note: OLE objects cannot be attached to Inbox messages. Note 1: To add a mail service, select “Add”, To remove a mail service, select the service from the Installed service box and select “Remove”. To view a mail service’s properties, select the service from the Installed service box and then select Properties. Figure 5-1 Inbox
Shin Chuan Computer User’s Manual SC800/SC820 5-11 5.2.2 Internet Explorer With Internet Explorer, you can view Web or intranet Web pages on your device. You will need to use a modem or WLAN to connect to an Internet server provider (ISP) or network. 5.2.2.1 Connect to the Internet Before you can view Web pages, you must set up a remote connection to your ISP or network. 5.2.2.2 Start Internet Explorer 9 Open Internet Explorer by selecting Start > Programs > Internet Explorer. 9 To get default home page, navigate to the desired default web page. 9 Select View > Internet Options from the command bar. 9 Enter the desired URL in the Start page field. 9 Press the OK button. Figure 5-2 Internet Explorer 5.2.2.3 Navigation Control Internet Explorer uses sliding menus for application and navigation control. Tap
Shin Chuan Computer User’s Manual SC800/SC820 5-12 and drag the sliding menus to the left or right to see the hidden menu items and toolbars. To achieve more screen real estate in Internet Explorer, you can hide the Status bar and View menu. From the top menu bar, go to View > Hide Toolbars. Once it is hidden, you must cold reset to access these features again. Refer to 2.7.2 “Cold Reset “for more information. 5.2.2.4 Set up a proxy server Proxy servers are often used when connecting to the Internet through a local network, such as a corporate network, for added security. 9 Select View > Internet Options > Connection Tab. 9 Select Access the Internet using a proxy server. 9 Enter the proxy server address and port. For more information, see your administrator. 9 To bypass the proxy server for local address, such as corporate intranet pages, select Bypass proxy for local address. 5.2.2.5 Enable Cookies A cookie file contains information about your identity and preferences so that a Web site can tailor information to your needs. The Web site sends the file and it is stored on your mobile device. 9 Select View > Internet Options > Security Tab. 9 Select Allow cookies. 5.2.2.6 Search for an Internet Site 9 Select View > Go > Search to search the web. 5.2.2.7 Go to an Internet address 9 Select Address Bar, if necessary to display the Address bar 9 Enter the address 9 Press “ENTER” key. 5.2.2.8 View previously visited sites 9 Tap the Arrow button at the right site of Address Bar 9 Select the Web Address you want to view.
Shin Chuan Computer User’s Manual SC800/SC820 5-13 5.2.2.9 Add and view Favorites 9 Go to the page you want add 9 Select Favorites > Add To Favorites. 9 If necessary, locate the folder you want. 9 Confirm or change the name. 9 To view your favorite Web sites, select Favorites and the Web site you want to view. Note:To organize your Favorites list, select Favorites > Organize Favorites. 5.2.2.10 Browse Web pages 9 To move to a page you have previously view, select View > Back 9 To move to the next page (provided you have viewed it previously), Select View > Forward. 9 To return to your Home page, select View > Go > Home. 5.2.2.11 Refresh current page 9 Select View > Refresh. 5.2.2.12 Stop loading a page 9 Select View > Stop. 5.2.2.13 View current page 9 Select View > Internet Options 9 To view the protocol, page type, size, and address, selects the General tab. 9 To view security information about the page, select the Security tab. 5.2.2.14 View HTML source code 9 While viewing the page, select File > Save As and save the file as .txt file. 9 Open the file in a word processing program, such as WordPad. 5.2.2.15 Change home and search page settings 9 Open the page you want to use as your home or search page. 9 Select View > Go > Home or Search. 5.2.2.16 Save a copy of current page You can save Web pages and view them later when you’re disconnected
Shin Chuan Computer User’s Manual SC800/SC820 5-14 from the Internet or Intranet without using cached memory. 9 Select File > Save As 9 Specify a folder location and give the file name. 5.2.2.17 Copy a Web page to a document 9 Select all or part of the Web page you want to copy. 9 Select Edit > Copy. 9 Go to the document where you want to place the information and select the location. 9 Select Edit > Paste. 5.2.2.18 Select security Options 9 Select View > Internet Options > Security tab 9 Select the security protocols you want. 5.2.2.19 Change the font size 9 Select View > Text Size and select the desired size. 5.2.3 Messenger The Windows CE Messenger client application in Windows CE.NET allows you to communicate real-time using text-based messaging, VOIP, and more. 9 See who’s online. See when your colleagues are online. You can also post your presence information to a list of watchers that you define. 9 Talk instead of type Stop typing Talk with a colleague anywhere in the world using the microphone and speakers on your device. Windows Messenger supports high-quality voice calling r Windows CE device. 9 Communicate using Session Initiation Protocol (SIP) or Hotmail contacts Windows Messenger supports. Communication with your colleagues in the enterprise with a SIP based communications service. You can also talk to your Hotmail contacts using the .NET Messenger. 5.2.4 Microsoft WordPad You can create and edit documents and templates in WordPad, using
Shin Chuan Computer User’s Manual SC800/SC820 5-15 buttons and menu commands that are similar to those used in the desktop version of Microsoft Word. You can work with files Normal or Outline view. WordPad documents are usually saved as .pwd files, but you can also save documents in other file formats, such as .rtf or .doc. 5.2.4.1 Selecting and Editing Text 9 Select text To select Do this Any amount of text Drag the stylus over the text. A word Double-tap the word. A single paragraph Triple-tap within the paragraph. An entire document Select Edit > Select All An picture Tap the picture 9 Find text ¾ To search for text in one part of a document, select that part. Otherwise, the whole document is searched. ¾ Select Edit > Find ¾ Enter the text you want to find. For a paragraph, enter ^p. For a tab stop, enter ^t. ¾ Select the search options you want. ¾ To continue searching, select Edit > Find > Next. 9 Replace text ¾ To replace text in one part of document, select that part. Otherwise, the whole document is searched. ¾ Select Edit > Replace. ¾ Enter the text you want to find and the text you want to replace it with. For a paragraph, enter ^p. For a tab stop, enter ^t. ¾ Select the replacement options you want. ¾ Select Find Next. ¾ On the Find/Replace toolbar, select the appropriate button. 9 Move, copy, or delete text ¾ Select the text you want to move, copy, or delete. ¾ To move or delete text, select the Cut button. To copy the text, select
Shin Chuan Computer User’s Manual SC800/SC820 5-16 the Copy button. ¾ To paste the information, move the insertion point to the desired location, and select the Paste button. Notes: z To undo an action, select Edit > Undo. z To restore the action, select Edit > Redo. 5.2.4.2 Formatting Text 9 Create bulleted and numbered lists ¾ Select the Bullets or Numbering button. ¾ Type the first item. ¾ Press ENTER, type the next item, and repeat as needed. ¾ Select the button again to end list formatting. Note: To change the number style for the selected list, select Format > Paragraph, In the Format list, select the style you want. 9 Set the default font ¾ Select Format > Font. ¾ Select the font you want. ¾ Select Set As Default ¾ To confirm that your changes will be applied to subsequent documents you create, select Yes. Note: To apply the default font and stylus to selected text, select Apply Default. 9 Select a different font ¾ Select the text you want to change. To select all text, select Edit > Select All. ¾ From the Font list, select the font you want. ¾ From the Font Size list, select a size. Note: To see more formatting options, select Format > Font. 9 Change font formatting ¾ Select desired text. ¾ Select the Bold, Italic, or Underline button. ¾ To change the color, select Format > Font and select the color you want from the Color list.
Shin Chuan Computer User’s Manual SC800/SC820 5-17 9 Adjust the paragraph alignment ¾ Select the paragraph you want to align. ¾ Select the Align Left, Center, or Align Right button. Note: To see more formatting options, select Format > Paragraph. 9 Indent a paragraph ¾ Select the paragraph you want to indent. ¾ Select Format > paragraph. ¾ Adjust the indentation settings as needed. 9 Set tabs ¾ Select Format > Tabs. ¾ Change the tab settings as needed. 5.2.4.3 Adjusting the Display 9 Wrap text in the window ¾ Select View > Wrap to Window. 9 Display the document using the full screen ¾ Select View > Full Screen. ¾ To exit Full Screen view, select Restore. ¾ To move the Restore button, drag the bar on the left side. 9 Display or hide scroll bars ¾ Select View > Horizontal Scroll Bar or Vertical Scroll Bar. 9 Zoom in or out ¾ Select View > Zoom, and select the desired percentage. Note: For Custom, enter the exact percentage and select OK. 5.2.4.4 Working in Outline View 9 Switch between Normal and Outline views ¾ Select View > Normal or Outline. 9 Assign and change outline levels ¾ Select View > Outline. ¾ Select the appropriate buttons on the toolbar.
Shin Chuan Computer User’s Manual SC800/SC820 5-18 5.2.4.5 Inserting Symbols 9 Place the insertion point where you want to insert the symbol. 9 Select Tools > Insert Symbols. 9 Select the symbol you want, and then select Insert. Tips: If you select a different font ( or subset of a font), a different set of Symbols will be displayed. 5.2.4.6 Printing a Document 9 Select File > Print. 9 Select the printing options you want. Tips: z Port list the available printer ports z If Network is selected from the Port list, enter the path to the network printer to the Net Path box. 5.2.4.7 Setting a password for a Document 9 Select File > password. 9 Type and verify the password. 9 You must save the document (File > Save) to return the password. 5.2.4.8 Converting Documents 9 About document conversion If an e-mail program is installed on your device and you receive an attached Word document or template created in Word version 6.0 or later, WordPad will convert the file on your device. To view the document, simply open the attachment in your e-mail program or open the file in the WordPad. During conversion, some formatting attributes may be changed or lost. To avoid losing these attributes permanently, close the file after viewing it rather saving the file on your device. If you save the file, save with a different file name. For more information about conversion performed on your device, see the following topics.
Shin Chuan Computer User’s Manual SC800/SC820 5-19 9 Changes caused by Word document conversion ¾ Formatting z Borders and Shading Borders and shading are not displayed in WordPad, but are restored when converted back to a Word document. Shading is not restored when used in a table, but simple borders are restored. z Character formatting Bold, italic, strikethrough, superscript, subscript, and hidden text are retained and displayed. Other effects are changed or removed. z Colors Colors are retained and mapped to colors available on your device. z Fonts and font sizes Fonts not supported by your mobile device are mapped to the closest font available in WordPad. z Page Formatting Headers, footers, footnotes, columns, pages setup information, and style sheets are removed during conversion to WordPad. WordPad supports built-in headings. z Paragraph formatting Tabs, alignment, bullets, indentation, simple numbered lists, and paragraph spacing are retailed and displayed in WordPad. ¾ Pictures Pictures are removed during conversion. ¾ Table of Contents Table of Contents text and some formatting are preserved. However, any text set at right-aligned tab stops may wrap to the next line. ¾ Index Index text and some formatting are preserved. ¾ Tables Tables appear as tab-delimited text. Cells containing wrapped text, tabs, or paragraph markers may be difficult to read. Simple tables are displayed accurately and restored when you convert the WordPad file back to a WordPad document.
Shin Chuan Computer User’s Manual SC800/SC820 5-20 ¾ OLE Objects OLE Objects are removed during conversion. ¾ Revisions marks, annotations, and comments Revision marks are visible but cannot be changed. Annotations and documents are removed during conversion. 5.2.5 Remote Connection Using Remote Desktop Connection, you can log on to Windows Terminal Server and use all programs installed on this server. For example, instead of running Microsoft Pocket Word, you can run the desktop version of Microsoft Word. 5.2.5.1 Connecting to Terminal Server 9 Select Start > Programs > Remote Connection, or run ‘CETSC’ from the command prompt. 9 In the Server box, type or select a Terminal Server name or TCP/IP address, or select a server in the drop-down list. 9 Select Connect. 9 In the Remote Connection window, type your user name, password, and domain(if required), and then select OK. Figure 5-3 Remote Connected
Shin Chuan Computer User’s Manual SC800/SC820 5-21 5.2.5.2 Disconnecting Without Ending a Session 9 In the Remote Connection window, select Start > Shutdown. 9 Select Disconnect > OK. Note: If you previously disconnected from a Terminal Server without ending the session, the Terminal Server will continue to execute any running processes and Remote Connection can later reconnect to this same session(if your administrator has configured Remote Connection to reconnect to disconnected sessions). 5.2.5.3 Disconnecting and Ending a Session 9 In the Remote Connection window, select Start > Shutdown. 9 Select Log Off > OK. 5.2.6 Windows Explorer Windows Explorer works almost the same on your PDT as it does on your PC. See the topics below for information about the difference in Windows Explorer on your device. 5.2.6.1 Navigating in File View 9 Go forwards and Back ¾ To go to the previous folder, select Go > Back. ¾ To go to the next folder (which you have just viewed), select Go > Forward. Figure 5-4 Windows Explorer
Shin Chuan Computer User’s Manual SC800/SC820 5-22 9 Use the Go menu ¾ To quickly access the My Documents folder, select Go > My Documents ¾ To see all of the folders you have accessed, select Go > History. Double-tap a folder to return to it. 5.2.6.2 Viewing Files as Icons Lists 9 To view icons, select View > Large Icons or Small Icons. 9 To view a list, select View > Details. 5.2.6.3 Working with Files and Folders 9 Create a new folder ¾ If necessary, open the folder where you want the new folder to reside. ¾ Select File > New Folder. 9 Add a folder to your Favorites list ¾ Open the folder ¾ Select Favorites > Add to Favorites. ¾ In the Name box, type the shortcut name. Tips: z To open a favorite file or folder, select Favorites and then select the folder. z To organize your favorites, select Favorites > Organize Favorites. 9 Transfer a file using infrared ¾ To send a file, select it, line up the infrared ports, and select File > Send To > Infrared Recipient. ¾ To receive a file, line up the infrared ports, and select File > Receive. 5.2.6.4. Creating Desktop Shortcuts 9 Display the file or Web page for which you want to create a Shortcut. 9 Select File > Send to. 9 Select Desktop as Shortcut. 5.2.6.5 Switch to Internet 9 Type a URL in the Address bar.
Shin Chuan Computer User’s Manual SC800/SC820 5-23 5.3 DiskOnChip The DiskOnChip let the application or a data file can be stored into the Flash Memory. Note: The DiskOnChip storage memory persists all reset (warm/cold reboot) conditions and software/firmware updates. We strongly recommends installing all applications, applets, programs, and important data files to the DiskOnChip Flash location. Caution: If an application or a data file is only installed or saved in RAM, a hard reset will result in the loss of that application or data file. 5.3.1 Saving to Flash To save an application or data to the Flash Memory, from your current application, select File > Save As > navigate to the DiskOnChip location and save it. 5.3.2 DiskOnChip Location To access the contents of DiskOnChip storage: 9 Double-tap the My Computer icon on the desltop. 9 Double-tap the DiskOnChip icon to view DiskOnChip. Figure 5-5 DiskOnChip
Shin Chuan Computer User’s Manual SC800/SC820 5-24 5.3.3 DiskOnChip Size The size of the DiskOnChip will vary, depending on the size of system firmware. 9 Inside the DiskOnChip directory, tap File > Properties. 9 The DiskOnChip Properties dialog: The number following Free is the amount of memory currently available on your device. Figure 5-6 DiskOnChip Size
Shin Chuan Computer User’s Manual SC800/SC820 A-1 Appendix A GPRS Function A.1 Using the GPRS Features Use the PDT to make and receive data and send. Your service provider may provide other useful services such as GPRS. The PDT can also be used to connect to an Internet Service Provider (ISP) or work network so you can browse the Web and read e-mail. You can connect to the Internet or work network via GPRS (General Packet Radio Service). A.1.1 SIM Card A SIM (Subscriber Identity Module) card is required to operate the GPRS features on your PDT. The SIM card is a plastic card embedded with a computer chip that stores and transacts data. After the SIM card is activated by your Telecom service provider, the computer chip will contain information about your phone number, service, registration information, and contacts, as well as memory to store text. A.1.2 Inserting a SIM Card Note: If the battery is already installed, you must remove it before inserting the SIM card. To insert the SIM card into the PDT: Figure A-1 Insert SIM Card into PDT 1) Remove the battery cover and battery 2) Pushes the iron stock to front unlocks the slot and lifts the slot 3 Insert a correctly oriented SIM card. 4 Put down the slot and push the iron stock to back lock the slot). 5) Back to move the battery and battery cover.
Shin Chuan Computer User’s Manual SC800/SC820 A-2 Figure A-2 Remove SIM Card from SIM Tray Note: Repeat the same steps to remove the SIM card from the SIM tray. A.1.3 Before Start: Warning! 1. Before start to using GPRS, you must wait the GPRS icon in the task bar to appear. 2. If you using GPRS before power off or suspend device, you must launch the AP again on next power-on the device. Procedures: 1. Double Tap icon to Launch GPRS program. 2. If you have setting the PIN code, you might input the PIN code. 3. If you don’t want use GPRS Function, You might disable GPRS to saving battery power Figure A-3 GPRS Launch Figure A-4 Enable GPRS Module
Shin Chuan Computer User’s Manual SC800/SC820 A-3 Figure A-5 Enable GPRS Module Process Figure A-6 Dial-up to GPRS? Figure A-7 GPRS Connecting-Please Figure A-8 GPRS Connected wait
Shin Chuan Computer User’s Manual SC800/SC820 A-4 Figure A-9 Launch PIN CODE Figure A-10 PIN Code Input GPRS Module Active Symbol: GPRS Module is Disable (Power off) GPRS Module is Enable (Power on) A.2 Select settings Click the button to selecting the setting for your want: Set GPRS Connection: The default COM Port of GPRS Module is COM 8. (Figure A-14). to create or to modify the internet connections. The AP preserves one standard setting; other establishment, please consult your mobile phone service provider define and not by oneself manual to set up.
Shin Chuan Computer User’s Manual SC800/SC820 A-5 Figure A-11 Set GPRS Connection Figure A-12 Set GPRS Connection Figure A-13 GPRS Properties Figure A-14 GPRS Connection Properties
Shin Chuan Computer User’s Manual SC800/SC820 A-6 Figure A-15 Configure-Port Settings Figure A-16 Configure-Call Options Figure A-17 TCP/IP Settings-General Figure A-18 TCP/IP Settings-Name Servers
Shin Chuan Computer User’s Manual SC800/SC820 A-7 Figure A-19 Set GPRS Connection- Figure A-20 Set GPRS Connection- Security Settings Bluetooth Figure A-21 Set GPRS Connection-Phone Number
Shin Chuan Computer User’s Manual SC800/SC820 A-8 A.3 Internet connection Warning! On the equipment, the fact of connecting to the Internet Explorer. Configuring the network operator The AP preserves one standard setting; other establishment, please consult your mobile phone service provider define and not by oneself manual to set up. This setting will produced an ‘GPRS Connection’ in the “Network and Dial-up Connections” Figure A-22 GPRS Connection Icon A.3.1 Connecting ●Connecting with the GPRS Application Double tap the “ GPRS Connection “ icon to enable GPRS connection. or Tap “ GPRS Connection “ icon and tap “ Connect “.
Shin Chuan Computer User’s Manual SC800/SC820 A-9 Figure A-23 GPRS Connection Figure A-24 GPRS Connection Properties Figure A-25 GPRS Connecting Figure A-26 GPRS Connecting
Shin Chuan Computer User’s Manual SC800/SC820 A-10 Figure A-27 GPRS Connecting Figure A-28 GPRS Connecting Figure A-29 GPRS Connected
Shin Chuan Computer User’s Manual SC800/SC820 A-11 Suspend / Resume The GPRS module can not connection automatically, while the device entry Suspended and Resumed. You shall re-connect manually. Figure A-30 GPRS Module Enable Figure A-31 GPRS Enable Process Figure A-32 GPRS Disabled
Shin Chuan Computer User’s Manual SC800/SC820 B-1 Appendix B Expansion Module Applicability B.1 RFID Applicability B.1.1 Read Mode Sub Item Description Remark OPEN Enable the RFID device. Please Tap it before use the RFID CLOSE Disable the RFID device ReadUID Read UID (Unique Identifier) code e of tag card Read 14443 Read UID (Unique Identifier) code of tag card Only for ISO 14443A tag card TagData Read all data of tag card storage memory ReadBlock Read someone block data of tag card storage memory Read Mode Choose the block before reading Start Enable the function for continuous reading the tags card UID Continue Mode Stop Disable the function for continuous reading the tags card UID Clear Clear the data of viewing area. Save Store the data of viewing area into a file Viewing Area Show the read data of tag card
Shin Chuan Computer User’s Manual SC800/SC820 B-2 Figure B-1 RFID Power On Figure B-2 Continue Mode-Start Figure B-3 RFID Power On Figure B-4 WriteMode B.1.2 Write Mode Sub Item Explaining Remarks Tag Type (TI, AMIC, Philips) Choose the tag card type before writing.
Shin Chuan Computer User’s Manual SC800/SC820 B-3 WriteAFI Write 2 bits AFI (Application Family Identifier) code to tag card. WriteDSFID Write 2 bits DSFID (Data Storage Format Identifier) code to tag card. Only input number, Num = 0 ~ 255 or 0 ~ FF.LockAFI Lock AFI code of tag card, the AFI code of tag card will be not writing after lock. LockDSFID Lock DSFID code of tag card, the DSFID code of tag card will be not writing after lock. ReadBlock Write 8 bits data to someone block of tag card storage memory. Only input hex number, Num = 0 ~ FFFFFFFF. LockBlock Lock someone block data of tag card storage memory, the block data of tag card will be not writing after lock. Block Write / Lock Choose the block before write / lock. Writing Area Input wanted to write into data of tag card. B.2 GPS Applicability B.2.1 Setup Tab: Sub Item Explaining Remarks COM Port Select Default Æ COM7 Baud Rate Select Default Æ 4800 Scan Scan the COM port. Start / Close GPS Start / Close GPS function. Cold Start Refresh GPS function to default. OPEN Enable the GPS Module. Please Tap it before use the GPS. CLOSE Disable the GPS device.
Shin Chuan Computer User’s Manual SC800/SC820 B-4 Log File Save log file “gpslog.txt” to “My Computer” folder. Viewing Area Show the state data of GPS. Figure B-5 GPS Info Figure B-6 GPS Power On Figure B-7 GPS Scan
Shin Chuan Computer User’s Manual SC800/SC820 B-5 B.2.2 GPS Info Tab: Figure B-8 Did not fix direction Figure B-9 Fixed direction
Shin Chuan Computer User’s Manual SC800/SC820 C-1 Appendix C 2D Barcode Scanner Setting C.1 Basic Tab Tab □ Icon to Enable or Disable bar code reader C.2 Code Configure Tab Tab □ Icon to Enable or Disable bar code type
Shin Chuan Computer User’s Manual SC800/SC820 C-2 C.3 Prefix and Suffix Tab
Shin Chuan Computer User’s Manual SC800/SC820 C-3 C.4 Quiet Zone Tab C.5 Read Mode Tab
Shin Chuan Computer User’s Manual SC800/SC820 C-4 C.6 ASCII Conversion Tab C.7 Advanced Tab
Shin Chuan Computer User’s Manual SC800/SC820 C-5 C.8 Firmware Upgrade Tab

Navigation menu