Shindaiwa Powerbroom Pb270 Owners Manual

PB270 to the manual f5a7dd97-7fa4-4166-b34e-d792d7ce5ece

: Shindaiwa Shindaiwa-Powerbroom-Pb270-Owners-Manual-204078 shindaiwa-powerbroom-pb270-owners-manual-204078 shindaiwa pdf

Open the PDF directly: View PDF .
Page Count: 28

PB270 POWERBROOM

Minimize the risk of injury to yourself and others! Read this

manual and familiarize yourself with the contents. Always wear

eye and hearing protection when operating this unit.

WARNING!

SHINDAIWA OWNER’S/OPERATOR’S MANUAL

X7502235300

05/10

2

The Shindaiwa PB270 PowerBroom is

designed and built to deliver superior

performance and reliability without

compromise to quality, comfort, safety

or durability.

Shindaiwa engines represent the leading

edge of high-performance engine

technology, delivering exceptionally

high power with remarkably low

displacement and weight. As an owner/

operator, you’ll soon discover for

yourself why Shindaiwa is simply in a

class by itself!

Warning and operational labels

Read and follow this manual,

make sure anyone using the

pruner does likewise. Failure

to do so could result in serious

personal injury or machine fail-

ure. Keep this manual for future

reference.

Always wear a hard hat to re-

duce the risk of head injuries

during operation of this ma-

chine. In addition, always wear

eye and hearing protection.

Shindaiwa recommends wear-

ing a face shield as additional

face and eye protection.

Beware of thrown objects. Keep

bystanders at least 15 M (50

feet) away during operation.

Introduction

Throughout this manual are special

“attention statements”.

Attention Statements

WARNING!

A statement preceded

by the triangular attention symbol

and the word “WARNING” con-

tains information that should be

acted upon to prevent serious bod-

ily injury.

CAUTION!

A statement preceded by the

word “CAUTION” contains infor-

mation that should be acted upon

to prevent mechanical damage.

IMPORTANT!

A statement preceded by the word

“IMPORTANT” is one that possesses

special significance.

NOTE:

A statement preceded by the word

“NOTE” contains information that is

handy to know and may make your job

easier.

DANGER!

A statement preceded by

the triangular attention symbol and

the word “DANGER” contains infor-

mation that should be acted upon to

prevent serious injury or death.

Echo,Inc. reserves the right to make

changes to products without prior

notice, and without obligation to

make alterations to units previously

manufactured.

IMPORTANT!

The information contained in these

instructions describes units available at

the time of publication.

Contents PAGE PAGE

PAGE

Do not use on unguarded el-

evated surfaces.

Maintain a shallow working

angle and avoid moving toward

the vertical.

IMPORTANT!

The operational procedures described in this manual are intended to help you get the most from this unit as well as to protect

you and others from harm. These procedures are guidelines for safe operation under most conditions, and are not intended

to replace any safety rules and/or laws that may be in force in your area. If you have questions regarding your PowerBroom,

or if you do not understand something in this manual, contact your local authorized Shindaiwa dealer. You may also contact

Shindaiwa Inc. at the address printed on the back of this Manual.

WARNING!

The engine exhaust from

this product contains chemicals

known to the State of California

to cause cancer, birth defects or

other reproductive harm.

Safety .................................................... 3

Product Description ............................ 5

Specifications ....................................... 5

Assembly .............................................. 6

Mixing fuel ........................................... 8

Filling the fuel tank ............................. 8

Starting the Engine ............................ 9

Stopping the Engine ......................... 10

Adjusting Engine Idle ....................... 10

Checking Unit Condition.................. 10

Operating ........................................... 11

Maintenance ...................................... 12

Long Term Storage ........................... 15

Troubleshooting Guide .................... 16

Warranty Statement .......................... 19

3

A PowerBroom operates at very high

speeds and has the potential to do serious

damage if misused, abused or mishandled.

To reduce the risk of injury, you must main-

tain control at all times, and observe all

safety precautions during operation. Never

permit a person without training or instruc-

tion to operate this machine!

Stay Alert

You must be physically and mentally fit to

operate this unit safely.

Safety

WARNING!

Never make unauthorized

attachment installations.

WARNING!

Never oper-

ate power equipment of any kind

if you are tired or if you are under

the inuence of alcohol, drugs,

medication or any other substance

that could affect your ability or

judgement.

Work Safely

WARNING!

Use Good Judgement

Sweeper belts may move when ■

starting engine. Place sweeper

belts on a smooth level surface

when starting.

Always make sure the Power-

■

Broom attachment is properly

installed and rmly tightened

before operation.

Always wear eye protection to

■

shield against thrown objects.

Never modify or disable any of the

■

unit’s safety devices.

Do not make unauthorized modi-

■

cations to this unit.

Make sure there are no missing or

■

loose fasteners, and that the igni-

tion switch and throttle controls are

working properly.

Do not operate the unit with the

■

mufer removed.

NEVER operate this unit indoors.

■

Operate this unit only in a well ven-

tilated area. Be aware of carbon

monoxide poisoning. Exhaust gases

and lubrication oil mist can cause

serious injury or death.

Always hold the machine rmly with

■

both hands when sweeping, and

maintain control at all times.

Always stop the engine immediately

■

and check for damage if you strike a

foreign object or if the unit becomes

tangled. Do not operate with broken

or damaged equipment.

Always clear your work area of trash

■

or hidden debris to help ensure

good footing.

Always use genuine Shindaiwa

■

parts and accessories when

repairing or maintaining this unit.

Stop the unit immediately if it

■

suddenly begins to vibrate or

shake. Inspect for broken, miss-

ing or improperly installed parts or

attachments.

Never transport the unit nor set

■

it down with the engine running.

An engine that’s running could be

accidentally accelerated causing

the drum assemblies to rotate.

Always disconnect the spark plug

■

wire before performing any main-

tenance work.

Always maintain this unit accord-

■

ing to this owner’s manual and

follow the recommended sched-

uled maintenance.

IMPORTANT!

Safety and Operation Information Labels: Make

sure all information labels are undamaged and read-

able. Immediately replace damaged or missing

information labels. New labels are available from

your local authorized Shindaiwa dealer.

Safety Labels

REA D THE

OPE RA T O R’S M ANUAL .

WEAR HEARI NG AND ANSI Z87.1

APP ROVED EYE PROTE CTION .

BEWA RE OF THROW N

DIR T AND DEBRI S.

MAI NTAIN A

SHA LLO W

WORKI NG

ANG LE…

DO NOT U SE ON UNGU ARDED

ELE V A TED SURFA CES.

…AVOI D MOV ING T O WARD

VER TIC AL.

8026 7Shin daiw a I nc.

This label indicates the minimum distance between

front handle and rear grip per ANSI B175.3.

4

The Properly Equipped Operator

Always operate with both hands

rmly gripping the unit.

Always protect yourself from hazards

such as thorny brush and ying debris

by wearing gloves and close tting

clothing that covers arms and legs.

Never wear shorts. Don’t wear loose

clothing or items such as jewelry that

could get caught in machinery or

underbrush. Secure long hair so it is

above shoulder level.

Always wear eye and hearing protection.

Shindaiwa recommends wearing a face shield as

additional face and eye protection.

Wear sturdy footwear with nonslip

soles to provide good footing. Steel-

toed safety boots are recommended.

Never operate unit bare-footed!

Keep a proper footing and do not

overreach—maintain your balance

at all times during operation.

Be Aware of the Working Environment

15 M

Be careful when operating on a slope or on slippery

terrain, especially during rainy weather or when pulling

debris toward you.

If the drum assemblies jam, switch the

engine OFF and inspect the drums,

axles and gearcase for damage.

Never operate the PowerBroom around

objects that could tangle in the drums

and cause loss of control.

Maintain a low working angle and

avoid steep angles of operation.

A steep working angle risks loss

of control of the machine.

Transport the

machine with the

engine OFF.

ALWAYS clear your work area of trash or

hidden debris that could be thrown back at you

or toward a bystander. When operating in rocky

terrain or near electric wires or fences, use

extreme caution to avoid contacting such items

with the sweeper belts.

Keep bystanders

at least 15 meters

away from the unit

while operating

to reduce the risk

of being struck by

thrown debris.

Be constantly alert for objects and debris that could be

thrown either from the sweeper belts or bounced from a

hard surface.

Keep away from rotating

sweeper belts or bristles at

all times, and NEVER lift a

moving attachment above

waist-height.

Never allow the engine to run at

high RPM without a load. Doing

so could damage the engine.

When transporting the unit in a

vehicle, tie it down securely to

prevent damage and fuel spillage.

Always keep the

handles clean.

Keep the unit as clean as

possible. Keep it free of loose

vegetation, mud, etc.

Safety (continued)

Do not use this unit on

rooftops or elevated surfaces

5

Product Description

Outer Tube

Grip

Gearcase

Throttle

Trigger

Tank protector

Ignition Switch

Spark Plug

Fuel Tank

Sweeper Belt

Sweeper Drum

Handle

PB270

Sweeper ns

Using the illustration as a guide, famil-

iarize yourself with your machine and

its various components. Understand-

ing your machine helps ensure top per-

formance, long service life and safer

operation.

WARNING!

Do not make unauthorized

modications or alterations to any

of these units or their components.

IMPORTANT!

The terms “left”, “left-hand”, and

“LH”; “right”, “right-hand”, and “RH”;

“front” and “rear” refer to directions as

viewed by the operator during normal

operation.

Specications

Engine Model S270

Engine Type 2-cycle, vertical-cylinder, air-cooled

Dry Weight (less sweepers) 5.2 kg/11.5 lb.

Dry Weight (Including sweepers) 9.8 kg/21.5 lb.

Bore x Stroke 34 x 30 mm/1.34 x 1.18 in.

Displacement 27.2 cc/1.7 cu. in.

Maximum Power Output 1.5 HP (1.1 kW) @ 7500 min-1

Fuel/Oil Ratio 50:1 with Shindaiwa Premium 2-cycle mixing oil

Fuel Tank Capacity 660 ml/22.3 oz..

Carburetor Type TK, diaphragm-type

Ignition One-piece electronic, transistor controlled

Spark Plug Champion CJ8Y / NGK BPMR7A

Air Cleaner Type Foam element

Starting Method Recoil

Stopping Method Slide switch

Transmission Type Automatic, centrifugal clutch w/worm gear

EPA Emission Compliance Period* Category A

*Specifications are subject to change without notice. *The EPA emission compliance period referred to on the emission compliance label located

on the engine, indicates the number of operating hours for which the engine has been shown

to meet Federal emission requirements. Category C = 50 hours (Moderate), B = 125 hours

(Intermediate) and A = 300 hours (Extended)

6

WARNING!

Do not make unauthorized

modications or alterations to your

pruner or its components.

Before assembling, make sure you have all

the components required for a complete

unit:

Engine assembly ■

Outer tube assembly ■

Drum kit with gearcase ■

Assembly

Prior to assembly

Kit containing operator’s handle, ■

hardware, owner/operator's manual,

tool kit for routine maintenance. Tool

kits vary by model and may inclue a

hex wrench, spanner, and a combina-

tion spark plug wrench/screwdriver.

Carefully inspect all components for

■

damage before assembling.

Main

Shaft

Tube

Clamp

Outer

Tube

Place the powerhead on a clean, flat 1.

surface, spark plug facing up.

Use the 4mm hex wrench to loosen 2.

the index screw and tube clamp

screw. Verify that the D-shaped shim

washer is positioned as shown

Add some moly-type EP grease 3.

to the splines on the end of the

mainshaft.

Slide the outer tube into the tube 4.

clamp until the tube bottoms. If instal-

lation is difficult, rotate the outer tube

or mainshaft slightly until you feel

the mainshaft splines engage with the

powerhead.

Connect the Outer Tube to the Powerhead

CAUTION!

Do not force the shaft tube into

the powerhead! Excessive force

can damage the shaft tube and

Clamp

Screw

Shim Washer

Hex

Wrench

Index

Screw

Shim

Washer

Installation

Decal

CAUTION!

Do not remove the D-shaped shim

washer! The shim washer prevents

damage from overtightening the

tube clamp screw.

Position the outer tube so that the 5.

ignition switch is facing up and the

throttle trigger is down.

Slide the outer tube into the power-6.

head until the throttle grip just con-

tacts the tube clamp.

Tighten the clamp screw firmly.7.

Loosen the index screw and

tube clamp screw

Tube Clamp

Screw

Throttle Cable and Ignition Leads

Unscrew the two throttle lever cover 1.

screws, and then separate the throt-

tle control halves as shown.

Working from the powerhead, push 2.

the throttle cable through the pas-

sageway in the base of the shaft tube

grip.

Insert the throttle cable end into the 3.

molded receptacle in the throttle

lever, and then lay the cable wire in

the molded slot in the throttle body.

In the reverse order of removal, reas-4.

semble the throttle body and cover

on the shaft tube.

Plug the red ignition lead from the 5.

shaft tube into the red lead from

the powerhead, and then connect

the black grounding wire to the

powerhead.

CAUTION!

Overtightening the throttle assembly

screws can permanently damage

the plastic throttle components!

Throttle

cable

Nut

Cover

screw

Cover

Ground lead

(black wire)

Ignition lead (red

wire)

Nylon tube

Molded

receptacle

Throttle cable

Unscrew and

separate the

throttle control

halves Throttle

assembly

Insert the throttle cable end into the

molded receptacle

Connect ignition leads

Insert outer tube into

powerhead

7

Adjustable Handle Installation

Follow these instructions if you wish to

use the PowerBroom’s adjustable handle

instead of the loop handle on youlr power-

head assembly. Remove the powerhead

assembly’s loop handle.

Remove both screws from the 1.

PowerBroom’s adjustable handle

assembly.

While spreading the handle at the 2.

mounting hole, position the handle

on the outer tube as shown.

Reinstall the two mounting screws in 3.

the handle, but do not tighten them

at this time.

Locate the handle at the best posi-4.

tion for operator comfort (usually

about 10 inches ahead of the throttle

lever), and secure it by tightening

the adjustment knob at the handle

base.

Handle

Hex Nut

Washer

Outer Tube

Adjustment Knob

Mounting Screw

Throttle Assembly

Washer

IMPORTANT!

One side of the handle is recessed to

receive the two hex nuts.

Assembly (continued)

Install the adjustable handle

3/16-1/4 inch (4-6 mm)

Throttle Free Play

Test the throttle lever for smooth 1.

operation. If any stiffness or binding

are noted, repeat Steps 1 through 4

(on the previous page).

Test the throttle lever for proper 2.

“free play” of approximately 7mm

in the idle position. If necessary,

adjustments can be made at the car-

buretor by loosening the cable lock-

nut and then raising or lowering the

cable adjuster as required.

Cable

Adjuster

Locknut

Throttle lever free play

Adjust throttle lever free play Raise or lower cable

adjuster as required

and then tighten

locknut

8

Assembly (continued)

The PowerBroom tool should

now be completely assembled.

Push one of the drum axles onto 1.

either of the two gearcase output

shafts. If necessary, rotate the drum

axle until the clevis pin hole in the

axle aligns with the matching hole in

the gearcase output shaft.

CAUTION!

The two drum assemblies are

identical, but each drum must be

installed with its recessed end

facing toward the gearcase.

Sweeper Assembly

Use a clevis pin and hitch pin to 2.

secure the drum axle to the shaft.

Slide the recessed end of a sweeper 3.

drum assembly over the installed

axle, and then push the drum down

the axle until the cotter pin hole in

the axle extends above the drum

surface.

Use a cotter pin to secure the drum 4.

assembly on the axle (see inset).

The cotter pin is designed to fit

tightly against the outboard end of

the drum, so you may need to com-

press the drum face slightly during

installation. spead the ends of the

cotter pin to secure.

Repeat Steps 1-4 to install the remain-5.

ing axle and drum assembly.

Secure the drum

axle to the shaft

Install drum

axle onto

output shaft

Drum

Axle

Cotter

Pin

Hitch

Pin

Clevis

Pin

Install the sweeper drum

assembly

Drum

Assembly

3

Secure with a

cotter pin

1

2

4

9

Handling Fuel

DANGER

Fuel is VERY ammable. Use extreme care when mixing, storing or handling or serious personal injury

may result.

• Use an approved fuel container.

• DO NOT smoke near fuel.

• DO NOT allow ames or sparks near fuel.

• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT or RUNNING!

• DO NOT ll fuel tanks indoors. ALWAYS ll fuel tanks outdoors over bare ground.

• DO NOT overll fuel tank. Wipe up spills immediately.

• Securely tighten fuel tank cap and close fuel container after refueling.

• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.

• Move at least 3m (10 ft.) from refueling location before starting the engine.

WARNING!

Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa

requirements are NOT approved for use in Shindaiwa gasoline engines. Use of alternative fuels may cause

performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including,

but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel

lines, gaskets, carburetors and other engine components.

Fuel Requirements

Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain

up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood

alcohol) is NOT approved.

Hybrid 4TM Mixture Oil - Engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD standards must be

used. Shindaiwa highly recommends using Shindaiwa Red ArmorTM engine oil in all Shindaiwa Hybrid 4TM engines to

protect the engine from harmful carbon build up, maintain engine performance, and increase engine life. Shindaiwa

Red ArmorTM engine oil exceeds ISO-L-EGD and J.A.S.O. M345/FD performance requirements. Engine problems

due to inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD certied

oil will void the engine warranty.

Mixing Fuel

Examples of 50:1 mixing quantities

IMPORTANT!

Shindaiwa Red ArmorTM engine oil may be mixed at 50:1 ratio for application

in all Shindaiwa engines sold in the past, regardless of ratio specied in those

manuals.

IMPORTANT!

Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30)

days, ninety (90) days when a fuel stabilizer is added. Use of unmixed, improp-

erly mixed, or stale fuel, may cause hard starting, poor performance, or severe

engine damage and void the product warranty. Read and follow instructions in

the Long Term Storage section of this manual.

10

Filling the fuel tank

WARNING!

Minimize the Risk of Fire

Place the unit on a flat, level surface.1.

Clear any dirt or other debris from around the fuel filler cap.2.

Remove the fuel cap, and fill the tank with clean, fresh fuel.3.

Reinstall the fuel filler cap and tighten firmly.4.

Wipe away any spilled fuel before starting engine.5.

CAUTION!

Slowly remove the fuel cap only after stopping the engine

NEVER ■ smoke or light res near the engine.

ALWAYS

■ stop the engine and allow it to cool before

refueling.

ALWAYS

■ Wipe all spilled fuel and move at least 3

meters (10 feet) from the fueling point and source before

starting.

NEVER

■ place ammable material close to the engine

mufer.

NEVER ■ operate the engine without the mufer and spark

arrester screen in place and in good working condition.

FUEL IS HIGHLY FLAMMABLE. ■

ALWAYS ■store gasoline in a container approved for

ammable liquids.

ALWAYS

■ inspect the unit for fuel leaks before each

use. During each rell, check that no fuel leaks from

around the fuel cap and/or fuel tank.

If fuel leaks are evident, stop using the unit immedi-

ately. Fuel leaks must be repaired before using the unit.

ALWAYS ■ move the unit at least 3 meters (10 feet)

away from a fuel storage area or other readily am-

mable materials before starting

the engine.

Storage - Fuel storage laws vary by locality. Contact

your local government for the laws affecting your area.

As a precaution, store fuel in an approved, airtight con-

tainer. Store in a well-ventilated, unoccupied building,

away from sparks and ames.

IMPORTANT!

Stored fuel may separate. ALWAYS shake fuel container

thoroughly before each use.

Mixing Instructions

1. Fill an approved fuel container with half of the required

amount of gasoline.

2. Add the proper amount of engine oil to gasoline.

3. Close container and shake to mix oil with gasoline.

4. Add remaining gasoline, close fuel container, and

remix.

IMPORTANT!

Spilled fuel is a leading cause of hydrocarbon emissions.

Some states may require the use of automatic fuel shut-

off containers to reduce fuel spillage.

After use

• DONOTstoreaunitwithfuelinitstank.Leakscanoccur.

Returnunusedfueltoanapprovedfuelstoragecontainer.

11

Starting the Engine

While holding the outer tube firmly 5.

with left hand. Use your other hand

to slowly pull the recoil starter han-

dle until resistance is felt, then pull

quickly to start the engine.

IMPORTANT!!

Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or

STOP.

IMPORTANT!

The primer system only pushes fuel

through the carburetor. Repeatedly

pressing the primer bulb will not flood

the engine with fuel.

CAUTION!

Do not pull the recoil starter to

the end of the rope travel. Pulling

the recoil starter to the end of

the rope travel can damage the

starter.

Slide the ignition switch to the “ON” 1.

position.

Set the throttle lever to the “fast 2.

idle”:

Squeeze the throttle lever toward a.

the handgrip on the shaft tube.

Depress and hold the throttle lock b.

button.

While depressing the throttle c.

lock button, release the throttle

lever.

Press the primer bulb until fuel can 3.

be seen flowing in the transparent

return tube.

Set the choke lever to the CLOSED 4.

position if engine is cold.

Return Tube

Closed

Make sure the

attachment is clear

of obstructions!

...and pull recoil

starter handle

upward

Hold

the unit

rmly...

WARNING!

Never start the engine

from the operating position.

WARNING!

The PowerBroom attach-

ment may rotate when the engine

is started!

IMPORTANT!

If the engine fails to start after several

attempts with the choke in the closed

position, the engine may be flooded

with fuel. If flooding is suspected, move

the choke lever to the open position

and repeatedly pull the recoil starter to

remove excess fuel and start the engine.

If the engine still fails to start, refer

to the troubleshooting section of this

manual.

When the engine starts, slowly 6.

move the choke lever to the

“OPEN” position. (If the engine

stops after the initial start, close

the choke and restart.)

Operating the throttle will auto-7.

matically disengage the fast idle

setting.

Throttle Lock

Button

IGNITION

SWITCH ON Primer Bulb

After the engine starts, open the ■

choke (if it is not already open) by

moving the choke lever down. Allow

the engine to warm up at idle 2 or 3

minutes before operating the unit.

Advancing the throttle makes the

■

cutting attachment turn faster;

releasing the throttle permits the

attachment to stop turning.

When the Engine Starts...

If the cutting attachment continues ■

to rotate when the engine returns

to idle, carburetor idle speed should

be adjusted (see “Adjusting Engine

Idle” below).

Open

After engine starts, move

choke to OPEN position

Close choke

Press primer bulb...

Slide ignition to ON

12

Idle the engine briefly before stopping

(about 2 minutes), then slide the igni-

tion switch to the “O” (Engine OFF)

position.

Stopping the Engine

Adjusting Engine Idle

Idle

Adjusting

Screw

The engine must return to idle speed

whenever the throttle lever is released.

Idle speed is adjustable, and must be set

low enough to permit the engine clutch

to disengage the cutting attachment.

Idle Speed Adjustment

Place the trimmer on the ground, 1.

then start the engine, and then allow

it to idle 2-3 minutes until warm.

If the attachment rotates when the 2.

engine is at idle, reduce the idle

speed by turning the idle adjustment

screw counter-clockwise.

If a tachometer is available, the engine 3.

idle speed should be final adjusted to

3,000 (±300) rpm (min-1).

Carburetor fuel mixture adjustments 4.

are preset at factory and cannot be

serviced in the field.

WARNING!

The cutting attachment

must NEVER rotate at engine idle!

If the idle speed cannot be adjusted

by the procedure described

here, return the trimmer to your

Shindaiwa dealer for inspection.

NEVER operate the unit with the pro-

tective devices (ignition switch, etc.)

removed!

ALWAYS make sure the PowerBroom

tool is properly installed and firmly

tightened before operation.

Use only authorized Shindaiwa parts

and accessories with your Shindaiwa

Multipurpose Tool. Do not make modi-

fications to your machine without the

written approval of Shindaiwa.

Checking Unit Condition

NEVER use a cracked or warped Pow-

erBroom drum or axle: replace it with a

serviceable one.

ALWAYS stop the engine immediately

and check for damage if you strike a for-

eign object or if the machine becomes

tangled. Do not operate with broken or

damaged equipment.

NEVER allow the engine to run at high

RPM without a load. Doing so could

damage the engine.

NEVER operate a machine with worn

or damaged fasteners or attachment

holders.

IGNITION SWITCH

OFF

13

Operating

The PowerBroom works best when its

rubber fins can quickly slide or “skim”

over the surface being swept. New or

replacement sweeper belts tend to grip

or drag on hard surfaces, and should

be thoroughly broken in or “scuffed”

before the broom is actually put to work.

Break-in is easily accomplished by oper-

ating the PowerBroom at full throttle for

3 to 5 minutes in loose gravel or similar

abrasive material.

Break-in and Operation

WARNING!

KEEP CLEAR of drum

assemblies during starting opera-

tions! The drums may rotate during

startup.

WARNING!

BURN DANGER! The

gearcase will become very hot dur-

ing normal operation.

When sweeping narrow areas such as

sidewalks, the PowerBroom can be

used to throw material directly ahead of

the operator. Clearing wider areas may

require sweeping at an angle to create

windrows to one side of the path being

cleared.

Windrows of lighter materials often

can be combined into one main row or

pile for eventual pickup, while heavy or

bulky material may need to be collected

row-by-row.

To pull debris from corners, reverse

sweeper drum rotation by turning the

powerhead over (throttle facing “up”).

DIRECTION OF

ROTATION

Sweeping

corners with the

PowerBroom upside

down

Sweeping Windrows

Adjustment Knob

…loosen the adjustment

knob to reverse the

handle.

For long-term inverted

operation…

Once broken in, a PowerBroom will

effortlessly move an amazing variety of

materials, ranging from snow or stand-

ing water to heavier objects such as

gravel or wood chips.

Experience will help you understand

the operating principles of the PowerB-

room, but safe operation must be prac-

ticed from the start.

Operating Techniques

Operate the PowerBroom at or near full

throttle with its sweeper fins resting on

the work surface.

IMPORTANT!

It is both tiring and unnecessary to lift

or hold the fins from the work surface

during sweeping.

WARNING!

Reversing the PowerB-

room will cause debris to be thrown

back toward the operator. When

reversing the PowerBroom, use

lower throttle settings and be aware

that thrown debris may also affect

your footing!

Debris shield p/n 99909-33021

A plastic debris shield is available from

your Shindaiwa dealer as a useful option

to your PowerBroom. The shield helps

prevent broadcasting debris when large

volumes of material are forced over the

top of the drum during operation.

Optional accessories

14

Maintenance

WARNING!

Before performing any

maintenance, repair, or cleaning

work on the unit, make sure the

engine and cutting attachment are

completely stopped. Disconnect the

spark plug wire before performing

service or maintenance.

WARNING!

Non-standard accessories,

cutting attachment, or replacement

parts may not operate properly with

your unit and may cause damage

and lead to personal injury.

Prior to each work day, perform the

following:

Remove all dirt and debris from the

■

engine, check the cooling fins and

air cleaner for clogging, and clean as

necessary.

Check the entire unit for leaking fuel

■

or grease.

Daily Maintenance

Carefully remove any accumula- ■

tions of dirt or debris from the muf-

fler and fuel tank. Check cooling

air intake area at base of crankcase.

Remove all debris. Dirt build-up in

these areas can lead to engine over-

heating, fire, or premature wear.

Clean any debris or dirt from the ■

sweeper attachment.

Check for loose or missing screws or

■

components. Make sure the cutter

attachment is securely fastened.

Make sure nuts, bolts, and screws

■

(except carburetor idle speed adjust-

ing screws) are tight.

IMPORTANT!

MAINTENANCE, REPLACEMENT

OR REPAIR OF EMISSION CONTROL

DEVICES AND SYSTEMS MAY BE PER-

FORMED BY ANY REPAIR ESTABLISH-

MENT OR INDIVIDUAL; HOWEVER,

WARRANTY REPAIRS MUST BE PER-

FORMED BY A DEALER OR SERVICE

CENTER AUTHORIZED BY ECHO, INC.

THE USE OF PARTS THAT ARE NOT

EQUIVALENT IN PERFORMANCE AND

DURABILITY TO AUTHORIZED PARTS

MAY IMPAIR THE EFFECTIVENESS OF

THE EMISSION CONTROL SYSTEM

AND MAY HAVE A BEARING ON THE

OUTCOME OF A WARRANTY CLAIM.

10-Hour Maintenance

Every 10 hours of operation (more

frequently in dusty or dirty conditions):

Remove the air cleaner element from

the carburetor and clean it thoroughly

with soap and water or compressed air,

let dry before reinstalling the element.

IMPORTANT!

Direct the air stream at the inside face

of the filter only!

CAUTION!

Never operate the unit if the air

cleaner assembly is damaged or

missing!

Loosen

Knob

Remove and clean or

replace the element

Mufer

This unit must never be operated with

a faulty or missing spark arrester or

muffler. Make sure the muffler is well

secured and in good condition. A worn

or damaged muffler is a fire hazard and

may also cause hearing loss.

Spark Plug

Keep the spark plug and wire connec-

tions tight and clean.

Fasteners

Make sure nuts, bolts, and screws

(except carburetor adjusting screws)

are tight.

15

spark plug gap--all models

Remove and clean or replace the

spark plug.

Adjust the spark plug electrode gap

■

to 0.024 0.028 inch (0.6-0.7 mm). If

the spark plug must be replaced, use

only an Champion CJ8Y or NGK

BPMR7A, or equivalent resistor type

spark plug of the correct heat range.

CAUTION!

Before removing the spark plug,

clean the area around the plug to

prevent dirt and debris from getting

into the engine’s internal parts.

Clean the spark plug

and check the gap at

the electrode.

10/15-Hour Maintenance

0.024–0.028 inch

(0.6–0.7 mm)

Maintenance (continued)

(more frequently in dusty or dirty

conditions)

Remove and clean the cylinder cover ■

and clean grass and dirt from the cyl-

inder fins.

Remove and replace the fuel filter

element.

Use a hooked wire to remove the ■

fuel filter element.

Before reinstalling the new filter

element, inspect the condition of all

the fuel system components (fuel

pick-up line, fuel return line, tank

vent line, tank vent, fuel cap and fuel

tank).

If damage, splitting or deterioration

is noted, the unit should be

removed from service until it

can be inspected or repaired

by a Shindaiwa-trained service

technician.

Filter

Element

Hooked Wire

50 hour maintenance

CAUTION!

Make sure you do not pierce the

fuel line with the end of the hooked

wire, the line is delicate and can be

damaged easily.

16

Gearcase Lubrication

The gearcase should be filled with 60 cc

(2.0 fl.oz.) of Mobil SHC634 Synthetic

Gear Oil. A maximum of 75-80 cc can be

used, but never to exceed 80 cc. Opera-

tion with excessive oil level will result

in high operating temperatures. Do not

overfill!

Turn the gearcase to the LH side 4.

and and allow all used gearcase oil to

drain into a small container.

Place the gearcase on the RH side 5.

and supported so the outer tube

is parallel to the ground. Refill the

gearcase with 60 cc (2.0 fl.oz) of

Mobil SHC634 Synthetic Gear Oil

to the bottom of the chamfer on

the output gear. The correct oil

depth is 5/8" (15.5 mm). DO NOT

OVERFILL!

NOTE:

It may be necessary to use a heat gun

to soften the sealer material.

WARNING!

BURN DANGER! The

gearcase will be extremely hot after

use!

Replacing the gearcase oil

Disconnect spark plug wire at 1.

engine.

Remove the LH Drum and axle 2.

assembly (as viewed from the operat-

ing position). Wipe the sideplate clean

and remove four screws (it is not nec-

essary to remove the gearcase from

the outer tube).

Turn gearcase side plate to break 3.

the seal and lift the plate from the

gearcase.

Inspect the sideplate for damage and 6.

clean off all remaining liquid gasket

material with brake cleaner or acetone.

Coat the outer sealing flange of the

sideplate with Loctite Ultragrey Silicon

Sealant or Threebond No. 1104 Liq-

uid Gasket.

Replace the cover and install the four 7.

sideplate screws. Tighten securely.

Reinstall the drum and axle assem-8.

bly. Refer to the section “Assembly:

Sweeper Assembly” for instructions.

300-hour maintenance

Turn gearcase side plate to break the seal

and lift the plate from the gearcase

Fill the gearcase to the bottom of the

chamfer on the output gear.

DO NOT OVERFILL!

Maintenance (continued)

17

Maintenance (continued)

Mufer

Spark

Arrester

Mufer Maintenance

WARNING!

Never operate the unit with

a damage or missing mufer or spark

arrester! Operating with a missing or

damaged spark arrester is a re hazard

and could also damage your hearing.

Hard starting or a gradual loss of perfor-

mance can be caused by carbon deposits

lodged in the muffler’s spark arrester

screen.

In such cases, performance can usually be

restored by removing the spark arrester

screen and giving it a thorough cleaning

with a stiff bristle brush.

If carbon deposits are severe or if no per-

formance improvement is noted, your unit

should be returned to your Shindaiwa

dealer for inspection.

Long Term Storage

Whenever the unit will not be used for 30

days or longer, use the following proce-

dures to prepare it for storage:

Clean external parts thoroughly and

■

apply a light coating of oil to all metal

surfaces.

Drain all the fuel from the carburetor

■

and the fuel tank.

To do so:

Prime the primer bulb until no more 1.

fuel is passing through.

Start and run the engine until it stops 2.

running.

Repeat steps 1 and 2 until the engine 3.

will no longer start.

Remove the spark plug and pour

■

about 1/4 oz. of engine oil into the

cylinder through the spark plug hole.

Slowly pull the recoil starter 2 or 3

times so oil will evenly coat the inte-

rior of the engine. Reinstall the spark

plug.

Before storing the unit, repair or

■

replace any worn or damaged parts.

Remove the air cleaner element from

■

the carburetor and clean it thor-

oughly with soap and water. Let dry

and reassemble the element.

Store the unit in a clean, dust-free

■

area.

CAUTION!

Gasoline stored in the carbure-

tor for extended periods can cause

hard starting, and could also lead to

increased service and maintenance

costs.

IMPORTANT!

All stored fuels should be stabilized with

a fuel stabilizer such as STA-BIL™.

NOTE

Damage resulting from stale or con-

taminated fuel is not covered by the

Shindaiwa warranty policy.

18

Troubleshooting Guide

Vaporlock.

Engine hot/heat soaked.

Low fuel quality.

Let cool completely and restart.

Refi ll with fresh, clean unleaded gasoline with a pump octane

of 89 or higher mixed with an air cooled engine oil that

meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils

at 50:1 gasoline/oil ratio.

What To Check Possible Cause Remedy

ENGINE DOES NOT START OR HARD TO START

NO

NO

NO

NO

Does the engine crank?

Good compression?

Does the tank contain fresh

fuel of the proper grade?

Is fuel visible and moving

in the return line when

priming?

Is there spark at the spark

plug wire terminal?

Check the spark plug.

Faulty recoil starter.

Fluid in the crankcase.

Internal damage.

Loose spark plug.

Excess wear on cylinder,

piston, rings.

Fuel incorrect, stale, or

contaminated; mixture incorrect.

Check for clogged fuel fi lter

and/or vent.

Priming pump not functioning properly.

The ignition switch is in

“O” (OFF) position.

Shorted ignition ground.

Faulty ignition unit.

If the plug is wet, excess

fuel may be in the cylinder.

The plug is fouled or improperly

gapped.

The plug is damaged internally

or of the wrong size.

Consult with an authorized Shindaiwa servicing dealer.

Tighten and re-test.

Consult with an authorized Shindaiwa

servicing dealer.

Refi ll with fresh, clean unleaded gasoline with a pump octane

of 89 or higher mixed with an air cooled engine oil that

meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils

at 50:1 gasoline/oil ratio.

Replace fuel fi lter or vent as required.

Re-start.

Consult with an authorized Shindaiwa

servicing dealer.

Move switch to “I” (ON) position

and re-start.

Consult with an authorized Shindaiwa

servicing dealer.

See "Starting a Flooded Engine"

Clean and gap the spark plug. Check the Specifi cations

section for the correct plug and gap for your unit. Restart.

Replace the spark plug. Check the Specifi cations section for

the correct plug and gap for your unit. Restart.

NO

YES

What To Check Possible Cause Remedy

ENGINE DOES NOT START

YES

YES

YES

YES

Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher

mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/

or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.

19

ADDITIONAL PROBLEMS

Poor acceleration.

Clogged air fi lter.

Clogged fuel fi lter.

Lean fuel/air mixture.

Idle speed set too low.

Ignition switch turned off.

Fuel tank empty.

Water in the fuel.

Clogged fuel fi lter.

Shorted spark plug or loose terminal.

Ignition failure.

Piston seizure.

Ground (stop) wire is disconnected,

or switch is defective.

Overheating due to incorrect spark plug.

Overheated engine.

Clean the air fi lter.

Replace the fuel fi lter.

Consult with an authorized Shindaiwa

servicing dealer.

Adjust idle. Check Specifi cations page for correct idle speed.

Reset the switch and re-start.

Refi ll with fresh, clean unleaded gasoline with a pump octane

of 89 or higher mixed with an air cooled engine oil that

meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils

at 50:1 gasoline/oil ratio.

Replace fuel fi lter.

Clean or replace spark plug. Check the Specifi cations section

for the correct plug and gap for your unit. Tighten

the terminal.

Replace the ignition unit.

Consult with an authorized Shindaiwa

servicing dealer.

Test and replace as required.

Replace the spark plug. Check the Specifi cations section for

the correct plug and gap for your unit. Restart.

Idle engine until cool.

Symptom Possible Cause Remedy

Engine stops abruptly.

Engine diffi cult to shut off.

Troubleshooting Guide (continued)

Is the engine overheating?

Engine is rough at all

speeds. May also have

black smoke and/or

unburned fuel at the

exhaust.

Operator is overworking the unit.

Carburetor mixture is too lean.

Improper fuel ratio.

Fan, fan cover, cylinder fi ns dirty

or damaged.

Carbon deposits on the piston or

in the muffl er.

Clogged air cleaner element.

Loose or damaged spark plug.

Air leakage or clogged fuel line.

Water in the fuel.

Piston seizure.

Faulty carburetor and/or diaphragm.

Overheating condition.

Improper fuel.

Carbon deposits in the

combustion chamber.

Use a lower throttle setting.

Consult with an authorized Shindaiwa

servicing dealer.

Refi ll with fresh, clean unleaded gasoline with a pump octane

of 89 or higher mixed with an air cooled engine oil that meets

or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1

gasoline/oil ratio.

Clean, repair or replace as necessary.

Consult with an authorized Shindaiwa

servicing dealer.

Service the air cleaner element.

Tighten or replace the spark plug.

Check the Specifi cations section for the correct plug and gap

for your unit.

Repair or replace fuel fi lter and/or

fuel line.

Refi ll with fresh, clean unleaded gasoline with a pump octane

of 89 or higher mixed with an air cooled engine oil that meets

or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1

gasoline/oil ratio.

Consult with an authorized Shindaiwa servicing dealer.

Consult with an authorized Shindaiwa

servicing dealer.

Refi ll with fresh, clean unleaded gasoline with a pump octane

of 89 or higher mixed with an air cooled engine oil that meets

or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1

gasoline/oil ratio.

Consult with an authorized Shindaiwa

servicing dealer.

What To Check Possible Cause Remedy

LOW POWER OUTPUT

Engine is knocking.

Troubleshooting Guide (continued)

Engine idle too high.

Broken clutch spring or worn clutch

spring boss.

Loose attachment holder.

Warped or damaged attachment.

Loose gearcase.

Cutting attachment

moves at engine idle.

Excessive vibration.

Cutting attachment will not

move.

Adjust idle. Check Specifi cations page for correct idle

speed.

Replace spring/shoes as required, check idle speed.

Inspect and re-tighten holders securely.

Inspect and replace attachment as

required.

Tighten gearcase securely.

Bent main shaft/worn or damaged bushings.

Shaft not installed in powerhead or gearcase.

Broken shaft.

Damaged gearcase.

Inspect and replace as necessary.

Inspect and reinstall as required.

Idle set too high. Adjust idle. Check Specifi cations page for correct

idle speed.

Engine will not idle

down. Engine has an air leak.

Consult with an authorized Shindaiwa servicing

dealer.

Consult with an authorized Shindaiwa servicing

dealer.

20

ADDITIONAL PROBLEMS

Poor acceleration.

Clogged air fi lter.

Clogged fuel fi lter.

Lean fuel/air mixture.

Idle speed set too low.

Ignition switch turned off.

Fuel tank empty.

Water in the fuel.

Clogged fuel fi lter.

Shorted spark plug or loose terminal.

Ignition failure.

Piston seizure.

Ground (stop) wire is disconnected,

or switch is defective.

Overheating due to incorrect spark plug.

Overheated engine.

Clean the air fi lter.

Replace the fuel fi lter.

Consult with an authorized Shindaiwa

servicing dealer.

Adjust idle. Check Specifi cations page for correct idle speed.

Reset the switch and re-start.

Refi ll with fresh, clean unleaded gasoline with a pump octane

of 89 or higher mixed with an air cooled engine oil that

meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils

at 50:1 gasoline/oil ratio.

Replace fuel fi lter.

Clean or replace spark plug. Check the Specifi cations section

for the correct plug and gap for your unit. Tighten

the terminal.

Replace the ignition unit.

Consult with an authorized Shindaiwa

servicing dealer.

Test and replace as required.

Replace the spark plug. Check the Specifi cations section for

the correct plug and gap for your unit. Restart.

Idle engine until cool.

Symptom Possible Cause Remedy

Engine stops abruptly.

Engine diffi cult to shut off.

Troubleshooting Guide (continued)

Is the engine overheating?

Engine is rough at all

speeds. May also have

black smoke and/or

unburned fuel at the

exhaust.

Operator is overworking the unit.

Carburetor mixture is too lean.

Improper fuel ratio.

Fan, fan cover, cylinder fi ns dirty

or damaged.

Carbon deposits on the piston or

in the muffl er.

Clogged air cleaner element.

Loose or damaged spark plug.

Air leakage or clogged fuel line.

Water in the fuel.

Piston seizure.

Faulty carburetor and/or diaphragm.

Overheating condition.

Improper fuel.

Carbon deposits in the

combustion chamber.

Use a lower throttle setting.

Consult with an authorized Shindaiwa

servicing dealer.

Refi ll with fresh, clean unleaded gasoline with a pump octane

of 89 or higher mixed with an air cooled engine oil that meets

or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1

gasoline/oil ratio.

Clean, repair or replace as necessary.

Consult with an authorized Shindaiwa

servicing dealer.

Service the air cleaner element.

Tighten or replace the spark plug.

Check the Specifi cations section for the correct plug and gap

for your unit.

Repair or replace fuel fi lter and/or

fuel line.

Refi ll with fresh, clean unleaded gasoline with a pump octane

of 89 or higher mixed with an air cooled engine oil that meets

or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1

gasoline/oil ratio.

Consult with an authorized Shindaiwa servicing dealer.

Consult with an authorized Shindaiwa

servicing dealer.

Refi ll with fresh, clean unleaded gasoline with a pump octane

of 89 or higher mixed with an air cooled engine oil that meets

or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1

gasoline/oil ratio.

Consult with an authorized Shindaiwa

servicing dealer.

What To Check Possible Cause Remedy

LOW POWER OUTPUT

Engine is knocking.

Troubleshooting Guide (continued)

Engine idle too high.

Broken clutch spring or worn clutch

spring boss.

Loose attachment holder.

Warped or damaged attachment.

Loose gearcase.

Cutting attachment

moves at engine idle.

Excessive vibration.

Cutting attachment will not

move.

Adjust idle. Check Specifi cations page for correct idle

speed.

Replace spring/shoes as required, check idle speed.

Inspect and re-tighten holders securely.

Inspect and replace attachment as

required.

Tighten gearcase securely.

Bent main shaft/worn or damaged bushings.

Shaft not installed in powerhead or gearcase.

Broken shaft.

Damaged gearcase.

Inspect and replace as necessary.

Inspect and reinstall as required.

Idle set too high. Adjust idle. Check Specifi cations page for correct

idle speed.

Engine will not idle

down. Engine has an air leak.

Consult with an authorized Shindaiwa servicing

dealer.

Consult with an authorized Shindaiwa servicing

dealer.

21

SHINDAIWA LIMITED WARRANTY STATEMENT FOR

PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010

ECHO, INC'S RESPONSIBILITY

ECHO Incorporated’s (ECHO, INC.) Limited Warranty, provides to the original purchaser that this Shindaiwa product is free from defects

in material and workmanship. Under normal use and maintenance from date of purchase, ECHO, INC. agrees to repair or replace at it’s

discretion, any defective product free of charge at any authorized Shindaiwa servicing dealer within listed below application time periods,

limitations and exclusions. THIS LIMITED WARRANTY IS ONLY APPLICABLE TO SHINDAIWA PRODUCTS SOLD BY AUTHORIZED

SHINDAIWA DEALERS. IT IS EXTENDED TO THE ORIGINAL PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT

OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair parts and accessories replaced under this warranty are warranted only

for the balance of the original unit or accessory warranty period. Any damage caused by improper installation or improper maintenance

is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO, INC. This warranty is

separate from the Emission control warranty statement supplied with your new product. Please consult the Emission Control Warranty

Statement for details regarding emission related parts. For a list of Authorized Shindaiwa Dealers refer to WWW.SHINDAIWA.COM or

call 1-877-986-7783.

OWNER’S RESPONSIBILITY

To ensure trouble free warranty coverage it is important that you register your Shindaiwa equipment on-line at WWW.SHINDAIWA.

COM or by lling out the warranty registration card supplied with your unit. Registering your product conrms your warranty coverage

and provides a direct link if we nd it necessary to contact you.

The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in

the operator’s manual. Should a product difculty occur, you must, at your expense, deliver or ship your Shindaiwa unit to an authorized

Shindaiwa servicing dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit

after the repairs have been made. For your nearest authorized Shindaiwa servicing dealer, call Shindaiwa’s Dealer Referral Center, at

1-877-986-7783 or you can locate a Shindaiwa servicing dealer at WWW.SHINDAIWA.COM. Should you require assistance or have

questions concerning Shindaiwa’s Warranty Statement, you can contact our Consumer Product Support Department at 1-800-673-1558

or contact us through the web at WWW.SHINDAIWA.COM.

PRODUCT WARRANTY PERIOD

RESIDENTIAL APPLICATION

• 2 YEAR WARRANTY - Units for residential, or non-income producing use will be covered by this limited warranty for two (2) years

from date of purchase.

EXCEPTIONS:

• For engine powered products, the electronic ignition module, exible drive cable, and solid drive shaft are warranted for the

life* of the product on parts only.

• Cutting attachments such as, but not limited to, bars, chains, sprockets, tines, blades, Power BroomTM, belts, and nylon trimmer

heads for residential or non-income producing use will be covered for failures due to defects in material or workmanship for a

period of 60 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not

covered by this warranty.

• Multipurpose Tool Attachments carry the same warranty duration as the units they are designed to t.

COMMERCIAL APPLICATION

• 90 DAY WARRANTY - All Chain Saws and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income producing use will be

covered by this limited warranty for 90 Days from the date of purchase.

• 2 YEAR WARRANTY - Units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this

limited warranty for two (2) years from the date of purchase.

EXCEPTIONS:

• For engine powered products, the electronic ignition module, exible drive cables, and solid drive shafts are warranted for the

life* of the product on parts only.

• Cutting attachments such as, but not limited to, bars, chains, sprockets, tines, blades, Power BroomTM, belts, and nylon trimmer

heads for commercial, institutional, agricultural, industrial, rental, or income producing will be covered for failures due to defects

in material or workmanship for a period of 30 days from original product purchase date. Any misuse from contact with concrete,

rocks, or other structures is not covered by this warranty.

• Multipurpose Tool Attachments carry the same warranty duration as the units they are designed to t.

RENTAL APPLICATION - 90 DAYS WARRANTY

• Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of

purchase.

* ECHO INC’s liability under the “Lifetime” coverage is limited to furnishing parts specied under the PRODUCT WARRANTY PERIOD

section of this warranty statement for “Life” free of charge for a period of ten (10) years after the date of the complete unit’s nal

production.

22

PURCHASED REPAIR PARTS AND ACCESSORIES

• 90-day all applications

ATTENTION ENGINE POWERED PRODUCT OWNERS

This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior

performance. To help ensure the performance of the unit, it is required to use engine oil which meets the ISO-L-EGD Standard per

ISO/CD 13738 and JASO M345/FD Standards. Shindaiwa Red ArmorTM

and Shindaiwa OneTM are a premium engine oil specically

formulated to meet ISO-L-EGD (ISO/CD 13738) and JASO M345/FD Standards. The use of engine oils designed for other applications,

such as for outboard motors or lawnmowers can result in severe engine damage, and will void your engine limited warranty.

THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:

• Lack of lubrication or engine failure, due to the use of engine oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO

M345/FD Standards. Shindaiwa ONETM Engine Oil meets the ISO-L-EGD and JASO M345/FD Standard. Emission related parts

are covered for 2 years regardless of engine oil used, per the statement listed in the EPA or California Emission Control Warranty

Explanation.

• Damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use

gasoline which contains 89 octane or higher. Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE (methyl/

tertiary/butyl/ether) is also approved. The prescribed mixing ratio of gasoline to oil is listed on the Shindaiwa oil label and covered

in your operator’s manual.

• Engine damage caused by use of ether or any starting uids.

• Damage caused by tampering with engine speed governor or emission components, or running engines above specied and

recommended engine speeds as listed in your operator’s manual.

• Operation of the unit with improperly maintained/removed cutting shield or removed/damaged air lter.

• Damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture.

• Defects, malfunctions or failures resulting from abuse, misuse, neglect, modications, alterations, normal wear, improper servicing,

or use of unauthorized attachments.

• Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the

operator's manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.

• Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized Shindaiwa servicing dealer

during the warranty period.

• Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.

• Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator's

Manuals.

• Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark

arrester screen.

• Adjustments after the rst (30) thirty days and beyond, such as carburetor adjustment and throttle cable adjustment.

• Damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure

to comply with recommended grease or oil change intervals.

• Damage caused by pump or sprayer running dry, pumping or spraying caustic or ammable materials, or lack of or broken

strainers.

• Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational

problem or failure occur, the product should not be used, but delivered as is to an authorized Shindaiwa servicing dealer.

It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your Shindaiwa

product or by visiting WWW.SHINDAIWA.COM. Your receipt of purchase including date, model and serial number must be maintained

and presented to an authorized Shindaiwa servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some

states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Some states do not

allow the exclusion or limitation of incidental or consequential damages, so you may also have other specic legal rights which vary from

state to state. This limited warranty is given by ECHO Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.

DISCLAIMER OF IMPLIED WARRANTIES

This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICULAR

PURPOSE OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product. ECHO, INC. and its afliated

companies shall not be liable for any special incidental or consequential damage, including lost prots. There are no warranties extended

other than as provided herein. This limited warranty may be modied only by ECHO, INC.

99922201031

02/05/2010

23

ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT

FOR ECHO AND SHINDAIWA BRANDS

The Environmental Protection Agency (EPA) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased

to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equipment/SORE must be

designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. ECHO Inc. must warrant the emission control system on

your equipment/SORE for the periods of time listed below, provided there has been no abuse, neglect or improper maintenance of your equipment/

SORE. Your emission control system may include parts such as: carburetor, fuel-injection system, ignition system, catalytic converter/mufer, fuel

tank, fuel feed lines, fuel cap assembly, spark plug, air lters, and other associated components. Where a warrantable condition exists, ECHO

Inc will repair your equipment/SORE at no cost to you including diagnosis, parts and labor. The Emission Control System warranty is extended

to the original owner including all subsequent owners.

MANUFACTURER'S WARRANTY COVERAGE:

The emission control system is warranted for 2 years or the length of the ECHO Inc. warranty, whichever is longer. If any emission-related part

on your equipment is defective, the part will be repaired or replaced by ECHO Inc. or its Authorized Service Representative.

OWNER'S WARRANTY RESPONSIBILITIES:

As the equipment/SORE owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. ECHO

Inc. recommends that you retain all receipts covering maintenance on your equipment/SORE however, ECHO Inc. cannot deny warranty solely

for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the equipment/SORE owner, you should be

aware that ECHO Inc. may deny you warranty coverage if your equipment/SORE or a part has failed due to abuse, neglect, improper maintenance

or unapproved modications.

You are responsible for presenting your equipment/SORE to an ECHO Inc. authorized service representative as soon as a problem exists. The

warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If a warrantable condition exists and there is no

Authorized Dealer within 100 miles, ECHO Inc. will pay to ship the unit to the nearest authorized dealer. If you have questions regarding your

warranty coverage, you should contact ECHO Inc. at 1-800-673-1558, web site WWW.ECHO-USA.COM or contact Shindaiwa at 1-877-986-

7783, web site WWW.SHINDAIWA.COM.

WHAT DOES THIS WARRANTY COVER?

ECHO Inc. warrants that your equipment/SORE was designed, built and equipped to conform with applicable EPA and C.A.R.B. emissions

standards and that your equipment/SORE is free from defects in material and workmanship that would cause it to fail to conform with applicable

requirements for 2 years or the length of the ECHO Inc. warranty, whichever is longer. The warranty period begins on the date the product is

purchased by an end user.

HOW WILL A COVERED PART BE CORRECTED?

If there is a defect in a part covered by this warranty, any ECHO Inc. Authorized Service Dealer will correct the defect. You will not have to pay

anything to have the part adjusted, repaired or replaced. This includes any labor and diagnosis for warranted repairs performed by the dealer. In

addition, engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted.

WHAT PARTS ARE COVERED?

Any applicable emission related part not scheduled for "required maintenance" will be repaired or replaced within the warranty period. The repaired

or replaced part will be warranted for the remaining ECHO Inc. warranty period.

Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated

above. Any such part repaired or replaced under warranty will be warranted for the remaining ECHO Inc. warranty period.

Any emission related part scheduled for replacement during "required maintenance" is warranted for the period of time prior to the rst scheduled

replacement point for that part. Any such part repaired or replaced under warranty shall be warranted for the remainder of the period prior to the

rst scheduled replacement point for that part.

Any manufacturer-approved replacement part may be used in the performance of any warranty maintenance or repairs on emission related parts,

and must be provided without charge if the part is still under warranty.

Any replacement part that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce

the warranty obligations of the manufacturer.

Throughout the equipment/SORE warranty period, ECHO Inc. will maintain a supply of warranted parts sufcient to meet the expected demand

for such parts.

SPECIFIC EMISSION RELATED WARRANTED PARTS:

• Electronic Ignition System • Spark Plug

• Catalytic Converter / Mufer Assembly • Carburetor (complete assembly or replaceable components)

• Choke • Fuel-Injection Assembly (or replaceable components)

• Fuel Tank • Fuel Cap Assembly

• Air Filter • Fuel Feed Line (and associated clamps/connectors as applicable)

WHAT IS NOT COVERED?

Any failure caused by abuse, neglect, improper maintenance, unapproved modications, use of unapproved add-on parts/modied parts or

unapproved accessories.

This Emission Control Warranty is valid only for the U.S.A., it's Territories, and Canada. 99922201033

01/2010

24

NOTES

25

NOTES

26

NOTES

27

NOTES

ECHO Incorporated.

400 Oakwood Road

Lake Zurich, IL 60047-1564 U.S.A.

Telephone: 1-877-986-7783

Fax: 1-847-540-8416

www.shindaiwa.com

Yamabiko Corporation

7-2 Suehirocho 1-Chome, Ohme,

Tokyo, 198-8760, Japan

Phone: 81-428-32-6118

Fax: 81-428-32-6145

Servicing Information

Parts/Serial Number

Genuine Shindaiwa Parts and Assemblies for your Shindaiwa products are available only from an Authorized

Shindaiwa Dealer. When you do need to buy parts always have the Model Number, Type and Serial Number of the

unit with you. You can nd these numbers on the engine. For future reference, write them in the space provided

below.

Service

Service of this product during the warranty period must be performed by an Authorized Shindaiwa Service Dealer.

For the name and address of the Authorized Shindaiwa Service Dealer nearest you, ask your retailer or call: 1-877-

986-7783. Dealer information is also available on WWW.SHINDAIWA.COM. When presenting your unit for Warranty

service/repairs, proof of purchase is required.

Consumer Product Support

If you require assistance or have questions concerning the application, operation or maintenance of this product you

may call the Shindaiwa Consumer Product Support Department at 1-877-986-7783 from 8:30 am to 4:30 pm (Central

Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit.

Warranty Registration

To ensure trouble free warranty coverage it is important that you register your Shindaiwa equipment by lling out the

warranty registration card supplied with your unit. Registering your product conrms your warranty coverage and pro-

vides a direct link if we nd it necessary to contact you.

Additional or Replacement Manuals

Replacement Operator and Parts Catalogs are available from your Shindaiwa dealer or at WWW.SHINDAIWA.

COM or by contacting the Consumer Product Support Department (1-877-986-7783). Always check WWW.SHINDAI-

WA.COM for updated information.

Copyright©2010ByEcho,Incorporated

AllRightsReserved.