Shure orporated UR1HF Bodypack Transmitter User Manual Revised 111808
Shure Incorporated Bodypack Transmitter Users Manual Revised 111808
Users Manual Revised 111808
UR1H Bodypack Transmitter Addendum Specifications: Features The following specifications apply • High RF power (250 mW) to the UR1H bodypack only. • Same audio performance as UR1 • Operates with alkaline or lithium batteries • Rapid, two-way infrared (IR) data transmission • External DC power connection • Optional remote mount antenna • Belt clip UR1H Warning: The UR1H belt clip must be installed as shown to ensure compliance with FCC RF exposure guidelines for safe use. Safety Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment is in direct contact with the body of the user under normal operating conditions. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For body-worn operation, the UR1H has been tested and meets the guidelines for safe use when used properly with the belt clip supplied or designated by Shure for use with this product. For safe use, do not remove or alter the position at the belt clip other than as instructed. Frequency Range Band Range H4, H4E 518-578 MHz J5 578-608, 614-638 MHz J5E 578-638 MHz L3E, L3 638-698 MHz Q5 740-814 MHz R9 790-862 MHz X1 944-952 MHz UR1H Transmitter Audio Input Connector: 4-Pin male mini connector (TA4M) Input Configuration: Unbalanced, active Actual Impedance: >1 MΩ Maximum Input Level: +10 dBu (sensitivity 0 dB) +20 dBu (sensitivity –10 dB) (1 kHz, 1% THD) TA4M Connector Pin Assignments: RF Carrier Frequency Range 518-862 MHz, depending on region RF Output Power 250 mW (24 dBm) across all tunable frequencies, maximum variation of -1.5 dB Power Requirements Two 1.5V AA batteries or 9 - 20 VDC, Shure PS22 adaptor recommended Plug size: 1.7 mm x 4.0 mm (.067 in. x .159 in) NOTE: This equipment has been tested and found to comply with the limits of a Class B digital device when used with PS22, pursuant to Part 15 of the FCC Rules. Current Drain: 350 mA maximum at the battery terminals with 3 VDC applied Battery Life (Typical): 3 hours, with 1.5V AA alkaline batteries 7 to 9 hours, with AA lithium primary batteries Overall Dimensions UR1H: 98 mm L x 60 mm W x 17 mm D (3.84 x 2.38 x 0.66 in.) Pin 1: Ground Pin 2: +5 VDC bias Pin 3: Audio Pin 4: Tied through active load (on main board) to Ground (On instrument adapter cable, Pin 4 floats) REPLACEMENT PARTS AND ACCESSORIES Furnished Accessories Antenna, 518-578 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Antenna, 578-698 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Antenna, 740-865 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Threaded Locking Adaptor TA4F. . . . . . . . . . . . . . . . . . . . . . . UA710 UA720 UA730 WA340 Optional Accessories Bodypack Pouch (Black). . . . . . . . . . . . . . . . . . . . . . . . . . . . . WA580B Bodypack Pouch (White). . . . . . . . . . . . . . . . . . . . . . . . . . . . . WA580W AC to DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PS22 Antenna Accessories Note: SMA to adaptor (UA910) is required to connect the following antenna accessories: Antenna, 944-952 MHz UA740 Passive Directional Wideband Antenna UA860SWB (470-1100 MHz) Net Weight 97 g (3.4 oz.) without batteries 2 ft. Coaxial Antenna Cable, BNC-BNC (RG58C/U) UA802 6 ft. Coaxial Antenna Cable, BNC-BNC (RG58C/U) UA806 UR1H Transmitter RF Output 25 ft. Coaxial Antenna Cable, BNC-BNC (RG8X/U) UA825 UA850 Connector: SMA 50 ft. Coaxial Antenna Cable, BNC-BNC (RG8X/U) Actual Impedance: 50 Ω 100 ft. Coaxial Antenna Cable, BNC-BNC (RG213/U) UA8100 Shell = Ground Center = Signal SMA to BNC Adaptor UA910 Pin Assignments: 27A11915 (Rev. 2) ©2008 Shure Incorporated Printed in U.S.A. Certification UR1H meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN 300 422 Parts 1 & 2. Note: 250 mW RF output power, EN 300 454 Parts 1 & 2, EN 301 489 Parts 1 & 9) and is eligible to carry the CE marking. Certified under FCC Parts 74 (FCC ID: DD4UR1HA, DD4UR1HB, DD4UR1HC, DD4UR1HF). Certified by IC in Canada under RSS-123 and RSS-102 (IC: 616A-UR1HA, 616A-UR1HB, 616A-UR1HC). The “EU Declaration of Conformity” can be obtained from Shure Inc. or any of its European representatives. For contact information please visit www.shure.com LICENSING INFORMATION: Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability depends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies. Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance FCC and IC Radiation Exposure Statement for Mobile Devices (when used with the UA860SWB) This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Modify Date : 2008:11:18 13:07:21-06:00 Create Date : 2008:11:18 13:06:45-06:00 Metadata Date : 2008:11:18 13:07:21-06:00 Creator Tool : Adobe InDesign CS3 (5.0) Format : application/pdf Document ID : uuid:989a28e2-507c-45e5-b12e-52cc298e5623 Instance ID : uuid:16c27a9e-d582-4f14-8f63-9b53ce51a67a Producer : Adobe PDF Library 8.0 Page Count : 2 Creator : Adobe InDesign CS3 (5.0)EXIF Metadata provided by EXIF.tools