Shure orporated UR3A Wireless Microphone Transmitter User Manual Exhibit D Users Manual per 2 1033 c3

Download:
Mirror Download [FCC.gov]
Document ID	1589806
Application ID	9lxaKk9cMJ6M4+qO5i+fVw==
Document Description	Exhibit D Users Manual per 2 1033 c3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	154.73kB (1934159 bits)
Date Submitted	2011-11-29 00:00:00
Date Available	2011-11-29 00:00:00
Creation Date	2011-11-10 09:20:07
Producing Software	Adobe PDF Library 9.9
Document Lastmod	2011-11-17 14:41:08
Document Title	Exhibit D Users Manual per 2 1033 c3
Document Creator	Adobe InDesign CS5.5 (7.5)

UR3 Plug-on Transmitter
©2011 Shure Incorporated
27A16156 (Rev. 1)
Printed in U.S.A.
UR3 Plug-on Transmitter
General Description
The UR3 is compatible with any wired XLR microphone and is an essential
component for professional field and media production applications. It is
comfortable to hold, features a back-lit display, and the audio level and power
indicator LEDs are discreetly hidden.
Features
•
•
•
•
•
•
•
•
•
•
① Joystick
Enter, exit and scroll using the
joystick
⑤ IR Window
For transmitting settings from
receiver to transmitter
② XLR Connection
Connects to any XLR wired
microphone or device output
⑥ Battery Compartment and
Battery Cap Retainer
Requires 2 AA batteries. Turn
cover counterclockwise to open
③ Power LED
Tri-color LED, green, amber and
red
UHF-R Audio Reference Companding
Wide-band tuning (region specific)
Smart, ergonomic industrial design
Selectable +12V/+48V phantom power
Sweepable high-pass filter
Programmable preset list with copy/paste to other UR3s
Selectable mic/line input
10/50 mW RF power
Discreetly located audio and battery life indicators
IR sync
④ Audio LED
Tri-color LED for audio settings,
red is peak
④
③
②
⑦ Power Switch
Press on, press and hold to
turn off
①
⑤
⑦
⑥
Setup
Joystick
Use the joystick for navigating and setting values.
Push Right (Enter)
Access a menu or apply the selected
value
1. Install batteries and turn power on.
Push Left (Exit)
2. Select the appropriate level, mic or line, to match the audio signal source:
AUDIO > SENS/GAIN > SENS
Exit without saving changes
Push Up/Down (Scroll)
3. Plug into an XLR microphone or the output of an audio device.
Scroll through menus or change a
value
4. Perform a sound check: Adjust the gain until the audio LED peaks red and
flickers amber:
Joystick Controls
AUDIO > SENS/GAIN > GAIN
Enter: Access a menu or
save the selected value
Scroll Up/Down:
Scroll through
menus or change
a value
SHURE
606.125MHz
MIC
Exit: Return to previous screen
Syncing with a UHF-R Receiver
Align IR windows with a UHF-R receiver and press sync on the receiver. The
transmitter displays SYNC SUCCESS.
radio
radio
audio
UTILITIES
utilities
®
RF
Audio
RF
ABJ
Audio
ABJ
779-810 MHz
Navigate
RF
Audio
ABJ
779-810 MHz
Navigate
Monitor
Control
OL
ENTER
UR4D+
OL
OL
push
Monitor Clip
Wireless Receiver
with Audio Reference
Companding
EXIT
sync
sync
®
®
RF
Audio
RF
ABJ
Audio
779-810 MHz
OL
ABJ
Navigate
RF
Audio
ABJ
779-810 MHz
Navigate
Monitor
Control
Power
ENTER
UR4D+
OL
OL
push
Wireless Receiver
with Audio Reference
Companding
Wireless Receiver
with Audio Reference
Companding
sync
Monitor Clip
EXIT
sync
sync
sens/gain
phantom
HPF
PRESET
SaVED
radio
audio
UTILITIES
radio
audio
UTILITIES
aud ITIES
UTIL
io
rad io
sens/gain
mic
exit enter sync scan
exit enter sync scan
Power
RF Settings
Audio Settings
AUDIO Menu
Use the RADIO menu to adjust the following RF settings:
RADIO Menu
SENS/GAIN > SENS
Adjusts input level to match audio signal source. MIC: For microphones or miclevel outputs
LINE: For line-level outputs.
SENS/GAIN > GAIN
Adjusts audio output to the receiver incrementally from −10 db to +20 db.
PHANTOM
Adds phantom power for condenser microphones. Select 12V or 48V as required
for the microphone.
HPF (ROLLOFF)
High-pass filter. Scroll up to turn on the filter and set the low-frequency rolloff in
Hz. (Scroll all the way down to turn off.)
SET FREQ
Adjusts group, channel or frequency.
RF PWR LVL
Selects 10 mW or 50 mW power level
DISABLE RF
Disables RF transmission. RF OFF appears on home screen.
ENABLE RF (if disabled)
Enables RF transmission
Utility Menu
Locking and Unlocking the Transmitter
UTILITIES Menu
To lock the transmitter, select UTILITIES > LOCK.
LOCK
1. From the home screen, hold the joystick to the right for 5 seconds or until UNLOCK? appears.
To unlock the transmitter:
Locks the transmitter to prevent changes to settings.
2. Push right again.
MIC PRESET
An on-screen key appears showing the joystick sequence to unlock the transmitter.
3. Follow the pattern to unlock the transmitter (up, down, left, right).
Acesses the preset list.
DISPLAY
Changes the home screen display format.
BATTERY
Sets battery type for more accurate battery life metering.
CONTRAST
Adjusts display contrast (press up/down).
SHURE
606.125MHz
MIC
RESTORE
Restores the factory default settings.
Microphone Preset
Accessing Presets
The transmitter holds up to 10 microphone presets.
Preset Submenu
To change or modify the presets, you must enter the microphone preset submenu:
UTILITIES > MIC PRESET. From the sub-menu you can select, modify, add or
delete and copy/paste settings.
Adding a preset:
UTILITIES > MIC PRESET>ADD
Use EXIT and ENTER to scroll between parameters. Use UP/DOWN to change
parameter values.
Note: ENTER through all parameter to save values.
SELECT
Use the preset submenu to add,
modify, or delete presets, or to clear
the preset list. The submenu is not
available until the first preset has been
entered.
Activates the selected preset.
Note: The UR3 is shipped with an
empty preset list.
Add a new preset after the selected
preset.
1. Access the preset list:
UTILITIES > MIC PRESET
DELETE
2. Scroll down to select a preset.
Deletes the selected preset.
DELETEALL
3. Push right to access the menu for
the selected preset.
MODIFY
Modify the selected preset.
ADD
Deletes all presets.
COPY/PASTE
Copy and paste the entire preset list to
another UR3.
Modify Microphone Presets
Power on with RF OFF (RF Safety Mode)
Choose a preset from the preset list, enter the submenu, and choose MODIFY.
Use this to turn on the transmitter without transmitting RF. This allows you to
change frequency settings on the transmitter without accidentally interfering with a
frequency being used by another transmitter.
Use the joystick to edit values:
Right: move to the next value.
Down: edit the selected value.
Left: exit the preset without saving changes.
1) Hold joystick to the left (exit) while turning on the transmitter power. RF OFF is
displayed on home screen.
2) Change and save your frequency settings as you normally would – the transmitter will not broadcast.
To exit and save: Continue to scroll right, through all fields, until PRESET SAVED
appears.
3) To transmit RF, power the transmitter off or turn the RF on thru the Main Menu,
MAIN MENU>RADIO> ENABLE RF.
To edit the eight-character name:
4) Change and save your frequency settings as you normally would – the transmitter will not broadcast.
1. Highlight the preset name and press the joystick down.
2. Scroll up/down to change the character.
3. Scroll right to move to the next character.
4. To exit, continue to scroll right past the last character.
Lock
Use this shortcut to power on the transmitter with the interface locked. This prevents accidental changes to transmitter settings. 			
Copy and Paste Preset List
1. On the destination UR3: select UTILITIES > MIC PRESET
1. While holding the joystick to the right, power on the transmitter.
Highlight MIC PRESET.
2. From the source UR3: select UTILITIES > MIC PRESET > COPY/PASTE.
The home screen displays the lock icon.
2. To unlock the transmitter, hold the joystick to the right for 5 seconds and follow
the on-screen instructions.
3. Align the IR windows and press enter on the source UR3.
SUCCESS appears on the LCD of the destination UR3.
Frequency Band
Frequency Range (MHz)
RF Power (mW)*
G1, G1E
470 - 530
10 / 50
H4, H4E
518 - 578
10 / 50
H4HK
518 - 565
10
J5
578-608, 614-638
10 / 50
10 / 50
J5E
578-638
J5HK
578 - 638
10
K4E
606 - 666
10 / 50
L3, L3E
638 - 698
10 / 50
M5E
694 - 758
10 / 50
P8
710 - 790
10 / 50
P9
710 - 787
10 / 50
Q5
740 - 814
10 / 50
R9
790 - 865
10 / 50
(10 mW only from 863-865)
MA24
779-788, 797-806
10
MJBX
806 - 810
10
R16
794 - 806
10 / 50
R18
794 - 806
10
X2
925 - 932
10
X1
944 - 952
10 / 50
Specifications
* conductive into 50 ohms
10
Modulation
FM (45kHz max. deviation)
Frequency Range
470 – 952 MHz (varies by region)
Working Range
Under typical conditions - 150 m (500 ft.)
Line-of-sight, outdoors for a single system 500 m, (1600 ft.)
Note: Actual range depends on RF signal
absorption,antenna efficiency, reflections, and
interference.
Tuning Bandwidth
Up to 80 MHz (varies by region)
Antenna
Dipole - Antenna is formed from the UR3 and attached
microphone
Carrier Frequencies
Up to 3200, tunable in steps of 25 kHz (varies by region)
RF Power Output
Selectable 10 mW or 50 mW max. (depending on region)
Power Requirements
(2) 1.5V AA alkaline
Battery Life
10 hours (alkaline) without phantom power @ 10mW,
typical (freq. band dependent)
3-4 hours (alkaline), with 48V phantom power @ 50mW,
typical (freq. band dependent)
Gain Adjustment
Range
-10 to +20 dB, MIC or LINE input setting
System Dynamic
Range
107 dB typical, Line Mode, A-weighted through a UR4
105 dB typical, Mic Mode, A-weighted through a UR4
102 dB typical, Line Mode, A-weighted through a UR5
100 dB typical, Mic Mode, A-weighted through a UR5
Pilot Tone
32 kHz
Frequency stability
± 0.0015%
Spurious Radiation
75 dB below carrier (typical)
Audio input jack
-127.0dBV, A-weighted (audio front end)
3-pin female XLR, Pin 1: Ground. Pin 2: Hot, Pin 3:
Cold
Equivalent input
noise
Phantom Power
Max. Audio Input
level
+24 dBV (Line Input, 0dB gain)
-21 dBV (Mic Input, 0dB gain)
+48V ± 4V, 7mA max.
+12V ± 1V, 7mA max.
Weight
196g (6.9 oz.) (with AA batteries)
Dimensions
Differential Input
impedance
6 kΩ LINE Input Setting
3 kΩ MIC Input Setting
99 x 66 x 23 mm
3.9 x 2.6 x 0.9 in.
H x W x D
System Frequency
response
35Hz – 17kHz, (+1.5dB, -3dB)
Note: Overall system frequency response depends on
the microphone element and receiver.
High Pass Filter
Two-pole (12dB per octave), selectable cut off frequency
from 40 Hz to 240Hz
System THD+N
<0.3%, 1kHz sine wave @ 6dB below clip (line and mic
input setting)
11
Certifications:
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de
l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en comprom - ettre le fonctionnement.
UR3: Type Accepted under FCC Parts 74 (FCC ID: DD4UR3A, DD4UR3B,
DD4UR3C, DD4UR3E, DD4UR3P).
Certified by IC in Canada under RSS-123 and RSS-102 (IC: 616A-UR3A, 616AUR3B, 616A-UR3C, 616A-UR3E).
LICENSING INFORMATION:
Meets essential requirements of the following European Directives:
Licensing: A ministerial license to operate this equipment may be required in certain areas.
Consult your national authority for possible requirements.
Changes or modifications not expressly approved by Shure Incorporated could void your
authority to operate the equipment. Licensing of Shure wireless microphone equipment is
the user’s responsibility, and licensability depends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate
telecommunications authority concerning proper licensing, and before choosing and ordering
frequencies.
R&TTE Directive 99/5/EC
• WEEE Directive 2002/96/EC, as ammended by 2008/34/EC
Please follow your regional recycling scheme for electronic waste
RoHS Directive 2002/95/EC, as ammended by 2008/35/EC Conforms to European
Regulation (EC) No. 1275/2008, as amended.
Meets requirements of the following standards: EN 300 422 Parts 1 and 2,
EN 301 489 Parts 1 and 9, EN60065.
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/
compliance
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference,and (2) this device must accept any interference, including interference that may causeundesired operation of the device.
12
RADIO
SET FREQ
radio
RF PWR LVL
audio
UTILITIES
radio
audio
UTILITIES
SENS/GAIN
AUDIO
PHANTOM
DISABLE RF
UTILITIES
HPF
LOCK
MIC PRESET
DISPLAY
BATTERY
CONTRAST
RESTORE
LIST
ADD
DELETE ALL
COPY/PASTE
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7262-9249-0 Fax: 49-7262-924911-4
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Create Date                     : 2011:11:10 09:20:07-06:00
Metadata Date                   : 2011:11:17 14:41:08-06:00
Modify Date                     : 2011:11:17 14:41:08-06:00
Creator Tool                    : Adobe InDesign CS5.5 (7.5)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 6482 bytes, use -b option to extract), (Binary data 2444 bytes, use -b option to extract)
Instance ID                     : uuid:d6b1105d-b916-42e0-a208-ae30648dda61
Document ID                     : xmp.did:5584C035EBDEE011BB8AA413B7758AD9
Original Document ID            : xmp.did:5584C035EBDEE011BB8AA413B7758AD9
Rendition Class                 : proof:pdf
History Action                  : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:5584C035EBDEE011BB8AA413B7758AD9, xmp.iid:5684C035EBDEE011BB8AA413B7758AD9, xmp.iid:5784C035EBDEE011BB8AA413B7758AD9, xmp.iid:5023CE24DAF4E011928F815901044418, xmp.iid:B7FAACE5B6F9E011BE89D1DA74376BC8, xmp.iid:A5E17EE64CFBE01180689247E852C91F, xmp.iid:A6E17EE64CFBE01180689247E852C91F, xmp.iid:1F88A9514DFBE01180689247E852C91F, xmp.iid:1619F19451FBE01180689247E852C91F, xmp.iid:7171A9F2D104E111AF7BC2123DA56E6F, xmp.iid:192377F75F06E11186809A6FBBDDF477, xmp.iid:721033518809E11186E6840B04819EFE
History When                    : 2011:09:14 11:06:18-05:00, 2011:09:14 11:07:06-05:00, 2011:09:14 11:07:06-05:00, 2011:10:12 15:44:37-05:00, 2011:10:18 13:27:55-05:00, 2011:10:20 13:54:51-05:00, 2011:10:20 13:54:51-05:00, 2011:10:20 13:58:14-05:00, 2011:10:20 14:27:57-05:00, 2011:11:01 16:39:16-05:00, 2011:11:03 16:08:24-05:00, 2011:11:07 15:34:48-06:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5
History Changed                 : /, /metadata, /, /, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata
Doc Change Count                : 41
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Count                      : 14
Creator                         : Adobe InDesign CS5.5 (7.5)

EXIF Metadata provided by EXIF.tools